Back

 1991 Holden Rodeo  

Upload Entry
21azi
  • 21azi
  • Budding User
  • Member No.: 169,957
  • Joined: 20-May 09
  • Posts: 543
Post #1 post 3rd August 2011 - 12:44 AM
Engine:

V6 VR Commodore Fuel Injected 3.8 S/2 Enginered
Chip Talk Chip in the ECU
K&N Air filter
Cam

Exhaust:
2 ½ inch Sports Exhaust
Extractors

Suspension:
Lowered at the back on 3 inch blocks with reset leaf springs
Gt gas shocks monro all round and urethane bushes
Lowered re-set rear leaf springs and got lowering blocks

Wheels:
18inch wheels (Lenso Sepiners)

Modifications:
Custom diff from a VL commodore Turbo (Brog Warner). Centre is LSD 28 spine axles and the diff gears are 3.45
V6 Engine
T5 gearbox conversion
Custom made hydraulic clutch
Custom and shaved tail gate
Cut off rollbar
Custom rollpan
Shaved fuel fuller and relocated to inside the tray
Shaved tray
Custom hard led on the tray

Stereo Audio / Visual:
Clarion T.V Touch screen pop-out DVD player Ipod, USB, SD card, mp3 Head Unit
Kenwood 1000w amp 2 Ch
2 x 12 inch Kenwood Sub's
Custom sub box
Sony 600w amp 4 Ch
Kenwood 6 ½ inch 3-ways 280w rear
Clarion 6 ½ inch 2 way spit 250w front door
Custom pod in the front doors for the Clarion


Estimated Power:

Not a Lot
But good for a tow car

This truck has been my project for the last 11years and I am only just finishing it off now.
\



This post has been edited by 21azi: Aug 3 2011, 01:00 AM
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo
1991 Holden Rodeo

TOP

Comments

  • Boost Network 27
  • 2FAS74U
    Post #2

    are the badges REALLY necessary? what part of this is a chev? besides that its good

    Burntsmoke
    Post #3

    Nice ute... aside from the rims and the badges and chrome it's not bad..

    re1600
    Post #4

    its not a chev, nor is any commodore

    stealth vk
    Post #5

    nice ute, did you do most of the work yourself?
    DC KUSTOMS
    Post #6

    The rims are spinning, they spinning man.... bwahahaha

    The chev badge, tail lights and spinner rims absolutely kill what is otherwise a very nice Rodeo..

    TwinCam16
    Post #7

    You were doin so well until the badges showed up.

    Ps will the L67 clear the firewall with the throttle body given that the motor is sitting that far back?

    21azi
    Post #8

    QUOTE (stealth vk @ Aug 3 2011, 07:56 AM) *
    nice ute, did you do most of the work yourself?


    Yes mate Engine,Diff, 1st Gearbox (auto) ,Paint, trim and body work.


    all apart from the T5 gearbox conversion Nizz Pro Gold Coast did that.

    LOL chev badge. I only put the chev badge was to cover the spot in the grill where the old Holden badge was that I lost.



    It will not be there for long as i am making a Billet grill soon

    21azi
    Post #9

    QUOTE (TwinCam16 @ Aug 3 2011, 08:35 AM) *
    You were doin so well until the badges showed up.

    Ps will the L67 clear the firewall with the throttle body given that the motor is sitting that far back?


    No it will not clear the firewall at all. That is why its not in yet as I do not wont to cut the shit out of the firewall and I am saling the Rodeo to get same fund to put it to my Skyline HR31 its off tap just need cash to finish it.
    4slips
    Post #10

    this the same one for sale for 21,ooo$$?

    RatDat
    Post #11

    Did you buy the wheels and the tail lights when you started the build haha.
    Pretty neat interior, engine conversion and paint but Remove spinners for black wheels tail lights for stock/smoked and get It permanently low.

    21azi
    Post #12

    QUOTE (4slips @ Aug 3 2011, 10:36 AM) *
    this the same one for sale for 21,ooo$$?


    Yes

    Gagginforit
    Post #13

    Jesus 21k? Anything with spinners cant be sold for over $1000.00 its the law!

    Looks like you spent some time and effort on the thing, hopefully you got the end product you hoped for.
    jebby88
    Post #14

    Looks good just don't like the tail lights and the chev badge. The motor is a Buick not a chev

    RatDat
    Post #15

    Also whats the go with the s/c engine and diff wheels half way down?

    21azi
    Post #16

    QUOTE (jebby88 @ Aug 3 2011, 01:46 PM) *
    Looks good just don't like the tail lights and the chev badge. The motor is a Buick not a chev



    So Funny

    V6 3800
    For all you know my engine could of came out of a:

    Buick, Holden, chev, GM, AMC, Pontiac, Oldsmobile, Jeepster and toyota all used the V6 3800.

    V6 3800 It was introduction in 1962 By GM. It has been in the Ward's 10 Best list multiple times.By then GM sold V6 3800 design rights to Kaiser-Jeep.Latter on GM bought back the rights off American Motors (AMC)how had bought the rights from Kaiser-Jeep.

    I am in a harry atm but I can point out more points.

    I should put a Toyota badge on it !.

    LOL

    21azi
    Post #17

    QUOTE (RatDat @ Aug 3 2011, 02:31 PM) *
    Also whats the go with the s/c engine and diff wheels half way down?



    I own the new s/c engine and if i keep the rodeo i will put it in. the wheels where off 1 of my cars and i just wanted to see how the 20s looked. Sham they are 5stud they would have looked good on the rodeo and the diff is out of a VL commodore Turbo (Brog Warner lsd) That me and my mate put in.

    krayziebenno
    Post #18

    i know i shouldn't like the rims, but for some reason the look pretty good on this. like the paint and interior too.

    photos aren't too shabby either
    2FAS74U
    Post #19

    post up your 31

    urluzn
    Post #20

    $23,000k on ebay seems a little steep for something like this, Can appreciate the time and money gone into this but still good luck finding a buyer who pays the much for this..
    Anyway Good luck with the sale..
    ayden m
    Post #21

    QUOTE (urluzn @ Aug 3 2011, 04:37 PM) *
    $23,000k on ebay seems a little steep for something like this, Can appreciate the time and money gone into this but still good luck finding a buyer who pays the much for this..
    Anyway Good luck with the sale..



    This but good luck on your sale !

    Distinctive.Detail
    Post #22

    wheels kill it.



    love the effort you've injected into this project tho.
    smile.gif

    21azi
    Post #23

    QUOTE (2FAS74U @ Aug 3 2011, 04:07 PM) *
    post up your 31


    LOL no one like my wheels on my skyline aswill lol

    This was the 1st paint and engine and the rest


    And Yes i have sold the wheels now.

    I have sold the old r34 neo engine and got a new one for it now. it is also AWD now and run a r33 gtr rear diff, cradle and Suspension and it is the same in the front r33 GTR cradle and shit.


    For same reason it will not let me post up more photo's ???????

    21azi
    Post #24

    QUOTE (Distinctive.Detail @ Aug 3 2011, 04:51 PM) *
    wheels kill it.



    love the effort you've injected into this project tho.
    smile.gif


    next project I wont to get a e type Jaguar or a old gt2000 Mustang
    21azi
    Post #25

    QUOTE (2FAS74U @ Aug 3 2011, 04:07 PM) *
    post up your 31



    Here the link for some reson i could not post pic up in this topic?


    https://www.boostcruising.com/forums/index....howtopic=753705

    Mustangchico24
    Post #26

    wow... thats actually pretty damm good mate.. good job.. im not a fan of spinners tho sad.gif

    Gagginforit
    Post #27

    Nice car, looks like a lot of work gone into this one as well! Top job, chop bowl is empty also!

    21azi
    Post #28

    QUOTE (Gagginforit @ Aug 4 2011, 11:07 AM) *
    Nice car, looks like a lot of work gone into this one as well! Top job, chop bowl is empty also!


    cheers

    LOL No mate

    If I did I would never get any thing done.

    • Member Login

      If you have a BoostCruising account enter your user name and password into the yellow box.

      Alternatively, you can quickly login with Facebook.

      If you don't have an account create one below.

      Create Account
    • Forgotten your password?
    • Login with Facebook

      Login using your Facebook account!

14 User(s) are reading this topic (14 Guests and 0 Anonymous Users)
0 Members:
Loading...
x