2014 Toyota Sienna Owners Manual

585

SIENNA_OM_OM45483U_(U)

3-6. Using the interior lights

Personal lights and rear ceiling lights

Personal lights (vehicles without overhead console)

On/off

On/off

On/off

Front

Rear

Rear ceiling lights (if equipped)

586

SIENNA_OM_OM45483U_(U)

3-6. Using the interior lights

■Adjusting the rear personal/interior lights angle

Push the edge of the light lens.

■Illuminated entry system (if equipped) Vehicles without a smart key system The lights automatically turn on/off according to the engine switch position, whether the doors are locked/ unlocked, and whether the doors are open/ closed. Vehicles with a smart key system The lights automatically turn on/off according to “ENGINE START STOP” switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and whether the doors are open/closed.

■To prevent battery discharge

If the lights remain on when a door is not fully closed and the personal/inte- rior light main switch is in door position, the lights will go off automatically after 30 seconds.

■Customization that can be configured at Toyota dealer

Settings (e.g. the time elapsed before lights turn off) can be changed. (Customizable features: P. 828)

NOTICE

■Rear ceiling lights (if equipped)

Do not hang anything on the gap between the ceiling light cover and the ceil- ing or pull the ceiling light cover strongly. Doing so may cause damage.

587

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features List of storage features

Auxiliary boxes Cup holders Door pockets Bottle holders Overhead console (if equipped) Glove boxes Console box (if equipped)

588

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Glove boxes

CAUTION

■Items that should not be left in the storage spaces

Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

●Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.

Glove boxes

Upper glove box

Push the button.

589

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Glove boxes

Lower glove box The lower glove box can be opened by pulling the lever and can be locked and unlocked by using the master key (vehicles without a smart key) or the mechanical key (vehicles with a smart key system).

Unlock Lock Open

■Removing the separate tray (upper glove box)

Pull out the separate tray.

CAUTION

■Caution while driving

Keep the glove box closed when not in use. In the event of sudden braking or sudden swerving, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.

590

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Console box

Console box (if equipped)

■ Using the console box Type A

Press the tab.

Type B

Press the tab.

591

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Console box

■Sliding the console box (type B)

From front

Press the tab and slide the console box.

From rear

Pull up the lever and slide the console box.

■Console box light

The console box light turns on when the headlight switch is on.

592

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Console box

CAUTION

■Caution while driving

Keep the console box closed when not in use. In the event of sudden brak- ing or sudden swerving, an accident may occur due to an occupant being struck by the open console box or the items stored inside.

■Console box adjustment precaution (type B)

●Do not adjust the position of the console box while the vehicle is moving. This may cause the driver to mishandle the vehicle and may lead to an accident that results in death or serious injury.

●Be careful not to get hands or feet pinched between the console box and

the rear sliding console or rear seat.

●Be careful not to allow the console box to hit any passenger while adjust-

ing its position.

●After adjusting the console box, make sure it is securely locked in position.

593

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Overhead console (if equipped)

Overhead console

Push the lid.

The overhead console is useful for temporarily storing small items.

CAUTION

■While driving

Do not leave the overhead console open. Items may fall out and cause injury.

■Maximum storage weight

Do not place any object heavier than 0.4 lb. (200 g) in it. The console may be opened and cause injury.

594

SIENNA_OM_OM45483U_(U)

Cup holders

Front

3-7. Using the storage features

Cup holders

Press in and release the front cup holder.

Console box (if equipped)

Console box type A (if equipped)

Pull the lid down.

595

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Console box type B (if equipped)

Cup holders

Second center seat (if equipped)

Removing seat. (P. 107)

the second center

Rear

596

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Cup holders

■Removing the separator (front)

Pull the separator up. The separator may be removed for clean- ing.

■Cup holder light (console box type A and B)

The cup holder light turns on when the headlight switch is on.

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.

■When not in use (front and console box type A)

Keep the cup holders closed. In the event of sudden braking or sudden swerving, an accident may occur due to an occupant being struck by the open cup holders or the items stored inside.

597

SIENNA_OM_OM45483U_(U)

Bottle holders

3-7. Using the storage features

Bottle holders

Type A

Type B

598

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Bottle holders

CAUTION

■Items unsuitable for the bottle holder

Do not place anything other than a bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.

NOTICE

■When stowing a bottle

Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders. The contents may spill. Type B: Make sure items in the sliding door bottle holder will not interfere with the motion of the door before operating the door. Items that protrude from the bottle holder may prevent door opening or damage the vehicle.

599

SIENNA_OM_OM45483U_(U)

Door pockets

Make sure magazines are not bent or protruding from the sliding door pockets. Do not insert anything too big so that the shape of the sliding door pockets is dis- torted. Such objects may obstruct the opening/closing of the sliding doors, dam- age the sliding door pockets or the vehi- cle body, and may result in a malfunction.

3-7. Using the storage features

Door pockets

Type A

Type B

NOTICE

■Door pockets (type B)

600

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Auxiliary boxes

Auxiliary boxes

Type A

Push down the knob.

Type B (if equipped)

Type C

SIENNA_OM_OM45483U_(U)

601

3-7. Using the storage features

Type D (if equipped)

Auxiliary boxes

Type E (if equipped)

Type F

Lift the lid.

602

SIENNA_OM_OM45483U_(U)

Type G (if equipped)

3-7. Using the storage features

Auxiliary boxes

Removing seat. (P. 107)

the second center

Type H (if equipped)

ITN37N026

Type I (if equipped)

ITN37N027

SIENNA_OM_OM45483U_(U)

603

3-7. Using the storage features

Type J (if equipped)

Auxiliary boxes

Type K (if equipped)

604

SIENNA_OM_OM45483U_(U)

3-7. Using the storage features

Auxiliary boxes

■Coin holder (type A)

Nickels, quarters and dimes can be stored separately.

CAUTION

■Caution while driving (type A and F)

Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking.

605

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Sun visors

To set the visor in the for- ward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it back- ward.

606

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Vanity mirrors

Flip down. Open the cover. The light turns on when the cover is opened.

NOTICE

■To prevent battery discharge

Do not leave the vanity lights on for extended periods while the engine is off.

607

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Clock

Vehicles with multi-information display P. 256
Vehicles without multi-information display

Adjusts the hours. Adjusts the minutes.

■The clock is displayed when

Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

■When disconnecting and reconnecting battery terminals

The time display will automatically be set to 1:00.

608

: If equipped

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Conversation mirror

The conversation mirror can provide the driver and the front passen- ger with a view of the rear seat area without the need to turn around.

STEP 1

STEP 2

Push the lid and allow the lid to open.

Push the lid. To first locked position.

: If equipped 609

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Power outlets

The power outlet can be used for the following components:

12 V: Accessories that run on less than 10 A 120 V AC: Accessories that use less than 100 W

■ 12 V Center panel type A

Center panel type B

610

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Luggage compartment

■ 120 V AC (if equipped) Power outlet socket console box type A

Power outlet socket console box type B

SIENNA_OM_OM45483U_(U)

611

3-8. Other interior features

Power outlet socket luggage compartment

■The power outlet can be used when Vehicles without a smart key system 12 V: The engine switch is in the “ACC” or “ON” position. 120 V AC: The engine switch is in the “ON” position. Vehicles with a smart key system 12 V: The “ENGINE START STOP” switch is in ACCESSORY or IGNITION

ON mode.

120 V AC: The “ENGINE START STOP” switch is in IGNITION ON mode.

612

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent blown fuse

12 V Do not use an accessory that uses more than 12 V 10 A. 120 V AC Do not use a 120 V AC appliance that requires more than 100 W. If a 120 V AC appliance that consumes more than 100 W is used, the protec- tion circuit may cut the power supply.

■To prevent battery discharge

Do not use the power outlet longer than necessary when the engine is not running.

■Appliances that may not operate properly (120 V AC)

The following 120 V AC appliances may not operate properly even if their power consumption is under 100 W: ●Appliances with high initial peak wattage ●Measuring devices that process precise data ●Other appliances that require an extremely stable power supply

613

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Seat heaters

For driver’s seat For front passenger’s seat On The indicator light comes on. Adjusts the seat tempera- ture The further you move the dial upward, the warmer the seat becomes.

■The seat heaters can be used when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

■When not in use

Move the dial fully downward. The indicator light turns off.

614

: If equipped

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

CAUTION

■Burns

●Use caution when seating the following persons in a seat with the seat

heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal-

lenged

• Persons with sensitive skin • Persons who are fatigued • Persons who have taken alcohol or drugs that induce sleep (sleeping

drugs, cold remedies, etc.)

●Do not cover the seat with anything when using the seat heater.

Using the seat heater with a blanket or cushion increases the temperature of the seat and may lead to overheating.

●Do not use the seat heater more than necessary. Doing so may cause

minor burns or overheating.

NOTICE

■To prevent seat heater damage

Do not put heavy objects that have an uneven surface on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.

■To prevent battery discharge

Turn the seat heaters off when the engine is not running.

615

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Armrests

Front seat

Pull the armrest down for use.

Second seat (if equipped)

Pull the armrest down for use.

616

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■Adjusting the armrests (if equipped)

Push the armrest down while pressing the button.

NOTICE

■To prevent damage to the armrest

Do not place too much strain on the armrest.

SIENNA_OM_OM45483U_(U)

617

3-8. Other interior features Assist grips

An assist grip (Type A) installed on the ceiling can be used to sup- port your body while sitting on the seat. An assist grip (Type B) installed on the pillar can be used when get- ting in or out of the vehicle and others.

Assist grip (Type A) Assist grip (Type B)

CAUTION

■Assist grip (Type A)

Do not use the assist grip (Type A) when getting in or out of the vehicle or rising from your seat.

NOTICE

■To prevent damage of the assist grip

Do not hang any heavy object or put a heavy load on the assist grip.

618

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Rear side sunshades

Rear door window

Rear quarter window

Pull the tab up. Secure the sunshade using the hooks. To retract the sunshade, pull the tab up slightly to unhook the sunshade, and lower the sunshade slowly.

Pull the tab up. Secure the sunshade using the hooks. To retract the sunshade, pull the tab up slightly to unhook the sunshade, and lower the sunshade slowly.

NOTICE

■To ensure normal operation of the sunshade

Observe the following precautions. ●Do not place anything where it may hinder the opening/closing of the sun-

shade.

●Do not place anything on the sunshade.

: If equipped 619

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Grocery bag hooks

The hooks are designed to hang things like a grocery bag. Type A (front seatback) (if equipped)

Type B (third seatback)

Type C (luggage compartment)

Pull the hook up.

620

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Type D (luggage compartment)

ITN38N036

CAUTION

■When not in use (type C)

Keep the grocery bag hook stowed. Injuries may result in the event of sudden braking, sudden swerving or an accident.

NOTICE

■Grocery bag hook weight capacity (type A and B)

Do not hang any object heavier than 8.8 lb. (4 kg) on the grocery bag hook.

621

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

STEP 1

the

Insert retaining hooks (clips) into the floor mat eye- lets.

STEP 2

Turn the upper knob of each retaining hook (clip) to secure the floor mats in place. *: Always align the

marks.

The shape of the retaining hooks (clips) may differ from that shown in the illustration.

622

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

CAUTION

Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver’s floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver’s seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P, fully depress each pedal to the floor to make sure it does not inter- fere with the floor mat.

623

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Luggage compartment features

■ Cargo hooks

Cargo hooks are provided for securing loose items.

■ Cargo net hooks Pattern 1

Pattern 2

624

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Storage box (if equipped)

Engage the latch buckle.

CAUTION

■When the cargo hooks are not in use

To avoid injury, always return the cargo hooks to their positions when they are not in use.

NOTICE

■To prevent damage to the cargo net hooks

Avoid hanging things other than a cargo net on them.

625

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Garage door opener

The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices.

The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.

Programming the HomeLink® (for U.S.A. owners)

The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.

Indicator light Buttons

626

: If equipped

SIENNA_OM_OM45483U_(U)

■ Programming the HomeLink® STEP 1

STEP 2

3-8. Other interior features

Point the remote control for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® control but- tons.

Keep the indicator light on the HomeLink® in view while pro- gramming.

the Press and hold one of HomeLink® buttons and the the transmitter button. When HomeLink® light changes from a slow to a rapid flash, you can release both but- tons.

indicator

If the HomeLink® indicator light comes on but does not flash, or flashes rapidly for 2 seconds and remains lit, the HomeLink® button is already programmed. Use the other buttons or the “Reprogramming a HomeLink® button” instructions. (P. 631)

follow

627

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

STEP 3

Test the operation of HomeLink® by pressing newly programmed button.

the the

the

hold

If programming a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type. Press and programmed HomeLink® button. The garage door has the rolling code feature if the HomeLink®) flashes rapidly for 2
seconds and then remains lit. If your transmitter is the Rolling Code type, proceed to the head- ing “Programming a rolling code system”.

light (on

indicator

the

STEP 4

Repeat the steps above to program another device for each of the remaining HomeLink® buttons.

628

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Programming a Rolling Code system (for U.S.A. owners)

If your device is Rolling Code equipped, follow the steps under the heading “Programming the HomeLink®” before proceeding with the steps listed below.

STEP 1

STEP 2

STEP 3

STEP 4

Locate the training button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the training button. Press the training button. Following this step, you have 30 seconds in which to initiate step 3
below. Press and hold the vehicle’s programmed HomeLink® button for 2 seconds and release it. Repeat this step once again. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® transceiver and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.

629

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Programming an entry gate (for U.S.A. owners)/Programming

all devices in the Canadian market

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

Place your transmitter 1 to 3 in. (25 to 75 mm) away from the surface of the HomeLink®. Keep the indicator light on the HomeLink® in view while programming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the device’s remote control button for two seconds each until step 4 is complete. When the indicator light on the HomeLink® compatible trans- ceiver starts to flashing rapidly, release the buttons. Test the operation of the HomeLink® by pressing the newly programmed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for each of the remaining HomeLink® buttons.

■ Programming other devices

To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.

■ Reprogramming a button

The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the programming instructions.

630

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Operating the HomeLink®

Press the appropriate HomeLink® button. The HomeLink® indicator light on the HomeLink® transceiver should turn on.

The HomeLink® continues to send a signal for up to 20 seconds as long as the button is pressed.

Reprogramming a HomeLink® button

Press and hold the desired HomeLink® button. After 20 seconds, the HomeLink® indicator light will start flashing slowly. Keep pressing the HomeLink® button and press and hold the transmitter button until the HomeLink® indicator light changes from a slow to a rapid flash. Release the buttons.

Erasing the entire HomeLink® memory (all three programs)

Press and hold down the 2 out- side buttons for 10 seconds until the indicator light flashes.

If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.

631

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■Before programming

●Install a new battery in the transmitter. ●The battery side of the transmitter must be pointed away from the

HomeLink® button.

■Certification for the garage door opener

For vehicles sold in the U.S.A. FCC ID: NZLWZLHL4
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For vehicles sold in Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

■For additional programming assistance with your HomeLink® Univer-

sal Transceiver Visit on the web at www.homelink.com or call 1-800-355-3515.

632

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

CAUTION

■When programming a garage door or other remote control device

The garage door may operate, so ensure people and objects are out of dan- ger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink® Compatible Transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an obstruction object. A door or device without these features increases the risk of death or serious injury.

633

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Compass

The compass on the trip information display indicates the direction in which the vehicle is heading. ■ Operation

To turn the compass on or off, press the switch.

■ Displays and directions

Display

NE SE SW NW

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

634

: If equipped

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Calibrating the compass

Samoa: 5 Guam: 8 Saipan: 8
The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle.

If you cross over a map boundary shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.

635

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Deviation calibration STEP 1

Stop the vehicle where it is safe to drive in a circle.

STEP 2

Press and hold the switch. A number (1 to 15) appears on the compass display.

STEP 3

Referring to the map above, press the switch to select the number of the zone you are in.

If the direction is displayed several seconds after adjustment, the calibration is complete.

■ Circling calibration

When “C” appears on the dis- play, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.

If there is not enough space to drive in a circle, drive around the block until the direction is dis- played.

636

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions: ●The vehicle is stopped immediately after turning. ●The vehicle is on an inclined surface. ●The vehicle is in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

●The vehicle has become magnetized.

(There is a magnet or metal object near the trip information display.)

●The battery has been disconnected. ●A door is open.

CAUTION

■While driving the vehicle

Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

637

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

NOTICE

■To avoid a compass malfunctions

Do not place magnets or any metal objects near the roof of the vehicle. Doing this may cause a malfunction of the compass sensor.

■To ensure normal operation of the compass

●Do not perform circling calibration of the compass in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields. ●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

638

SIENNA_OM_OM45483U_(U)

3-8. Other interior features Safety Connect

Safety Connect is a subscription-based telematics service that uses Global Positioning System (GPS) data and embedded cellular tech- nology to provide safety and security features to subscribers. Safety Connect is supported by Toyota’s designated response center, which operates 24 hours per day, 7 days per week. Safety Connect service is available by subscription on select, telematics hardware-equipped vehicles. By using the Safety Connect service, you are agreeing to be bound by the Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Con- nect service is subject to such then-applicable Terms and Condi- tions. ■ System components

Microphone LED light indicators “SOS” button

: If equipped 639

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Services

Subscribers have the following Safety Connect services avail- able: ● Automatic Collision Notification*

Helps drivers receive necessary response from emergency service providers. (P. 642) *: U.S. Patent No. 7,508,298 B2

● Stolen Vehicle Location

Helps drivers in the event of vehicle theft. (P. 643)

● Emergency Assistance Button (SOS)

Connects drivers to response-center support. (P. 643)

● Roadside Assistance

Provides drivers various on-road assistance. (P. 643)

■ Subscription

After you have signed the Telematics Subscription Service Agreement and are enrolled, you can begin receiving services. A variety of subscription terms is available for purchase. Contact your Toyota dealer, call 1-800-331-4331, or push the “SOS” but- ton in your vehicle for further subscription details.

640

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■Safety Connect Services Information

●Phone calls using the vehicles Bluetooth® technology will not be possible

during Safety Connect.

●Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection avail- ability, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support. Enroll- ment and Telematics Subscription Service Agreement required. A variety of subscription terms is available; charges vary by subscription term selected.

●Automatic Collision Notification, Emergency Assistance, Stolen Vehicle Location, and Enhanced Roadside Assistance will function in the United States, including Hawaii and Alaska, and in Canada. No Safety Connect services will function outside of the United States in countries other than Canada.

●Safety Connect services are not subject to section 255 of the Telecom-

munications Act and the device is not TTY compatible.

■Languages

The Safety Connect response center will offer support in multiple languages. The Safety Connect system will offer voice prompts in English and Spanish. Please indicate your language of choice when enrolling.

■When contacting the response center

You may be unable to contact the response center if the network is busy.

641

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Safety Connect LED light Indicators

When the engine switch is turned to the “ON” position (vehicles with- out a smart key system) or the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system), the red indicator light comes on for 2 seconds then turns off. Afterward, the green indicator light comes on, indicating that the service is active. The following indicator light patterns indicate specific system usage conditions: ● Green indicator light on = Active service ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunc-

tion (contact your Toyota dealer)

● No indicator light (off) = Safety Connect service not active

Safety Connect services

■ Automatic Collision Notification

In case of either airbag deployment or severe rear-end collision, the system is designed to automatically call the response center. The responding agent receives the vehicle’s location and attempts to speak with the vehicle occupants to assess the level of emer- gency. If the occupants are unable to communicate, the agent automatically treats the call as an emergency, contacts the nearest emergency services provider to describe the situation, and requests that assistance be sent to the location.

642

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■ Stolen Vehicle Location

If your vehicle is stolen, Safety Connect can work with local author- ities to assist them in locating and recovering the vehicle. After fil- ing a police report, call the Safety Connect response center at 1- 800-331-4331 and follow the prompts for Safety Connect to initiate this service. In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com.

■ Emergency Assistance Button (“SOS”)

In the event of an emergency on the road, push the “SOS” button to reach the Safety Connect response center. The answering agent will determine your vehicle’s location, assess the emer- gency, and dispatch the necessary assistance required. If you accidentally press the “SOS” button, tell the response-center agent that you are not experiencing an emergency.

■ Roadside Assistance

Subscribers can press the “SOS” button to reach a Safety Connect response-center agent, who can help with a wide range of needs, such as: towing, flat tire, fuel delivery, etc. For a description of the Roadside Assistance services and their limitations, please see the Safety Connect Terms and Conditions, which are available at Toyota.com.

643

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

Safety information for Safety Connect

Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals

The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile wire- less phones. Those guidelines are consistent with the safety stan- dards previously set by the following U.S. and international standards bodies. ● ANSI (American National Standards Institute) C95.1 [1992] ● NCRP (National Council on Radiation Protection and Measure-

ment) Report 86 [1986]

● ICNIRP (International Commission on Non-Ionizing Radiation

Protection) [1996]

Those standards were based on comprehensive and periodic eval- uations of the relevant scientific literature. Over 120 scientists, engineers, and physicians from universities, and government health agencies and industries reviewed the available body of research to develop the ANSI Standard (C95.1). The design of Safety Connect complies with the FCC guidelines in addition to those standards.

644

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

■Certification for Safety Connect

FCC ID: O9EGTM1 FCC ID: O6Y-CDMRF101
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

645

SIENNA_OM_OM45483U_(U)

3-8. Other interior features

646

SIENNA_OM_OM45483U_(U)

Maintenance and care

4-1. Maintenance and care Cleaning and protecting the vehicle exterior......... 648
Cleaning and protecting the vehicle interior.......... 653

4-2. Maintenance Maintenance requirements.................. 657
General maintenance....... 660
Emission inspection and maintenance (I/M) programs........................ 664

4-3. Do-it-yourself maintenance

Do-it-yourself service precautions .................... 665
Hood ................................ 669
Positioning a floor jack ..... 671
Engine compartment........ 673
Tires ................................. 688
Tire inflation pressure ...... 699
Wheels ............................. 703
Air conditioning filter......... 706
Wireless remote control/ electronic key battery..... 708
Checking and replacing fuses .............................. 711
Light bulbs........................ 724

647

SIENNA_OM_OM45483U_(U)

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition: