2014 Toyota Sienna Owners Manual

●8-passenger models: Be sure to raise the stowed second center seat above the outer trim, when removing from the storage box of the luggage room.

119

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

NOTICE

■Stowing the seat belt

The seat belts and the buckles must be stowed before you fold down the rear seatbacks.

■To prevent an ottoman malfunction (vehicles with Ottoman seats)

●Do not place any objects in the second passenger footwell that could pre-

vent the operation of the ottoman.

●Do not place heavy luggage on the ottoman. ●Do not place anything under the ottoman when in use. There is a possibil- ity that something may get caught and cause damage when stowing the ottoman.

120

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory

Your preferred driving position (the position of the driver’s seat and outside rear view mirrors) can be memorized and recalled with the touch of a button. It is also possible to set this function to activate automatically when the doors are unlocked. Two different driving positions can be entered into memory. ■ Entering a position to memory STEP 1

Vehicles without a smart key system Turn the engine switch to the “ON” position. Vehicles with a smart key system Turn the “ENGINE START STOP” switch to IGNITION ON mode. Adjust the driver’s seat and outside rear view mirrors to the desired positions.

STEP 2

STEP 3

Press the “SET” button, then within 3 seconds press button “1” or “2” until the signal beeps.

If the selected button has already been preset, the previ- ously recorded position will be overwritten.

: If equipped 121

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Recalling the memorized position

Check that the shift lever is in P.

STEP 1

STEP 2

Vehicles without a smart key system Turn the engine switch to the “ON” position. Vehicles with a smart key system Turn the “ENGINE START STOP” switch to IGNITION ON mode.

Press button “1” or “2” to recall the desired position.

122

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

Linking driving position memory with door unlock operation

Record your driving position to button “1” or “2” before performing the following: Vehicles without a smart key system Carry only the wireless remote control to which you want to link the driving position. STEP 1

Unlock the vehicle with the wireless remote control to which you want to link the driving position. Shift the shift lever to P and close the driver’s door. Turn the engine switch to the “ON” position.

STEP 2

STEP 3

Press the desired button (“1” or “2”) to recall the position. Then, while keep pressing the button, press lock switches (either lock or unlock) until the signal beeps.

the driver’s door

the driver’s door

The driving position is recalled when is unlocked using the wireless remote control and the driver’s door is opened.

123

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

Vehicles with a smart key system Carry only the electronic key to which you want to link the driving position. If 2 or more keys are in the vehicle, the driving position can- not be linked properly. STEP 1

Shift the shift lever to P and close the driver’s door. Turn the “ENGINE START STOP” switch to IGNITION ON mode.

STEP 2

Press the desired button (“1” or “2”) to recall the position. Then, while keep pressing the button, press lock switches (either lock or unlock) until the signal beeps.

the driver’s door

the driver’s door

The driving position is recalled when is unlocked using the wireless remote control and the driver’s door is opened.

124

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

■Operating the driving position memory after turning the engine off

Vehicles without a smart key system Memorized positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again, even after turning the engine switch to the “LOCK” position. Vehicles with a smart key system Memorized positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again, even after turning the “ENGINE START STOP” switch off.

■Stopping seat position operation part-way through

Perform any of the following operations. ●Press the “SET” button. ●Press button “1” or “2”. ●Adjust the seat using the switches (only cancels seat position recall).

CAUTION

■Seat adjustment caution

Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel.

125

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints

Head restraints are provided for all seats. Front and second outside seats

Up Pull the head restraints up. Down Push the head restraint down while pressing the lock release button.

Lock release button Second center* and third center seats Up Pull the head restraints up. Down Push the head restraint down while pressing the lock release button.

Lock release button

Third outside seats

*: 8-passenger models only

To use Pull the head restraints up. To fold Push the head restraint down while pressing the lever down- ward.

126

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

■Adjusting the height of the head restraints

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

■Adjusting the center seat head restraints

Always raise the head restraint one level from the stowed position when using.

■Removing the head restraints

Pull the head restraint up while pressing the lock release button. The head restraint of third outside seat can not be removed.

127

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

■Installing the head restraints (front, second and third center seats)

Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.

CAUTION

■Head restraint precautions

Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure

they are locked in position.

●Do not drive with the head restraints removed.

128

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts

Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts

Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der. Position the lap belt as low as possible over the hips. Adjust the position of the seatback. Sit up straight and well back in the seat. Do not twist the seat belt.

■ Fastening and releasing the seat belt

To fasten the seat belt, push the plate into the buckle until a click sound is heard. To release the seat belt, press the release button.

Release button

129

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Adjusting the seat belt shoulder anchor height (front and

second outside Tip-up seats)

Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.

Third center seat belt

The third center seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation.

Make sure that the buckle is securely latched for ready use of the center seat belt.

the

tab

“B” with

Matches hooked end. Matches tab “A” with the con- cave end.

130

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Release method

The belt can be completely released when not required, such as when folding down the third seat.

STEP 1

STEP 2

Insert the key or tab “A” into the hole on the center seat belt buckle to release the hooked tab “B” and allow the belt to retract. Retract the belt slowly when releasing and stowing the seat belt.

Stow the seat belt tabs in the cover set in the roof as shown.

■ Extracting the belt

Pull tab “B” out and pull the belt out a little. Pull tab “A” out.

131

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

Seat belt pretensioners (front seats)

The pretensioners help the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.

The pretensioners do not activate in the event of a minor frontal impact, a side impact, a rear impact or a vehicle rollover.

Pre-collision seat belts (front seats of vehicles with pre-collision system)

If the pre-collision sensor detects that a collision is unavoidable, the pre-collision system will retract the seat belt, thus enhancing the effectiveness of the seat belt pretensioner in a crash.

The same will happen if the driver makes an emergency braking or loses control of the vehicle. (P. 340)

■Emergency locking retractor (ELR)

The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.

■Automatic locking retractor (ALR)

When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (P. 196)

132

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

■Pregnant women

Obtain medical advice and wear the seat belt in the proper way. (P. 129) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.

■People suffering illness

Obtain medical advice and wear the seat belt in the proper way. (P. 129)

■Child seat belt usage

The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (P. 191) ●When the child becomes large enough to properly wear the vehicle’s

seat belt, follow the instructions on P. 129 regarding seat belt usage.

■Replacing the belt after the pretensioner has been activated

If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.

133

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

■Seat belt extender

If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.

they are not

CAUTION

Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or severe injury. ■Wearing a seat belt

●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt

for more than one person at once, including children.

●Toyota recommends that children be seated in the rear seat and always

use a seat belt and/or an appropriate child restraint system.

●To achieve a proper seating position, do not recline the seat more than necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.

●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips. ●Always wear the belt with the shoulder portion over the outside armrest

and the lap portion under the outside armrest.

134

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When children are in the vehicle

Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

■Seat belt pretensioners

●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.

●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.

■Adjustable shoulder anchor

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (P. 130)

135

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Seat belt damage and wear

●Do not damage the seat belts by allowing the belt, plate, or buckle to be

jammed in the door.

●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.

●Ensure that the belt and tab are locked and the belt is not twisted.

If the seat belt does not function correctly, immediately contact your Toyota dealer.

●Replace the seat assembly, including the belts, if your vehicle has been

involved in a serious accident, even if there is no obvious damage.

●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.

136

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When using the third center seat belt

Do not use the third center seat belt with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking or a collision.

■Using a seat belt extender

●Do not wear the seat belt extender if you can fasten the seat belt without

the extender.

●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.

●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.

NOTICE

■When using a seat belt extender

When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.

137

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel

The steering wheel can be adjusted to a comfortable position.

STEP 1

STEP 2

Hold the steering wheel and press the lever down.

Adjust to the ideal position by moving the steering wheel horizontally and vertically.

After adjustment, pull the lever up the steering wheel.

to secure

CAUTION

■Caution while driving

Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident and resulting in death or serious injury.

138

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror

Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror

Normal position Anti-glare position

Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.

Turns automatic mode on/off

The indicator comes on when automatic mode is turned on. Vehicles without a smart key system The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position. Vehicles with a smart key system The mirror will revert to the automatic mode each time the “ENGINE STOP” switch is turned to IGNITION ON mode.

START

139

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

Adjusting the height of rear view mirror

Adjust the height of the rear view mirror by moving it up and down.

■To prevent sensor error (vehicles with auto anti-glare inside rear view

mirror)

To ensure that the sensors operate prop- erly, do not touch or cover them.

CAUTION

■Caution while driving

Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.

140

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors

Mirror angle can be adjusted using the switch.

STEP 1

STEP 2

To select a mirror to adjust, press the switch.

Left Right

To adjust the mirror, press the switch.

Up Right Down Left

141

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

Folding back the mirrors

Manual type

Push the mirror back in the direc- tion of the vehicle’s rear.

Power type

Press the switch to fold the mir- rors.

Press it again to extend them to the original position.

142

SIENNA_OM_OM45483U_(U)

1

1-3. Adjustable components (seats, mirrors, steering wheel)

■Mirror angle can be adjusted when

Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.

■When the mirrors are fogged up (vehicles with outside rear view mirror

defoggers) Turn on the mirror defoggers to defog the mirrors. (P. 421)

■Automatic adjustment of the mirror angle (vehicles with driving posi-

tion memory) A desired mirror face angle can be entered to memory and recalled automat- ically by the driving position memory. (P. 121)

■Auto anti-glare function (vehicles with auto anti-glare inside rear view

mirror) When the anti-glare inside rear view mirror is set to automatic mode, the out- side rear view mirrors will activate in conjunction with the anti-glare inside rear view mirror to reduce reflected light. (P. 139)

■Linked mirror function when reversing (if equipped)

The outside rear view mirrors will automatically angle downwards when the vehicle is reversing in order to give a better view of the ground. However, this function will not operate when the mirror select switch is in the neutral position (between “L” and “R”).

143

SIENNA_OM_OM45483U_(U)

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When driving the vehicle

Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly

adjusted before driving. ■When a mirror is moving

To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.

■When the mirror defoggers are operating (vehicles with outside rear

view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

144

SIENNA_OM_OM45483U_(U)

1

1-4. Opening and closing the windows and moon roof Power windows

The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:

Window lock switch

Closing One-touch closing* Opening One-touch opening*

*: To stop the window partway, operate the switch in the oppo- site direction.

Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.

145

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

■The power windows can be operated when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■Operating the power windows after turning the engine off

Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened. Vehicles with a smart key system The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.

■Jam protection function

If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.

146

SIENNA_OM_OM45483U_(U)

1

1-4. Opening and closing the windows and moon roof

■When the power window does not close normally

If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the relevant door. ●After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position (vehicles without a smart key sys- tem) or the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system).

●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure. STEP 1

Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed.

STEP 2

STEP 3

Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely.

Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.

If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

147

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

CAUTION

■Closing the windows

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●Do not allow children to operate the power windows.

Closing a power window on someone can cause serious injury, and in some instances, even death.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the window fully closes.

●The jam protection function is disabled if the switch is pulled and held dur-

ing one-touch closing operation.

148

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof Quarter windows

The quarter windows can be opened to bring in fresh outside air for additional ventilation. Manual type

Pull the handle and swing the window fully out to open.

Power type

Opening Closing Both the left and right quarter windows move.

149

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

■The windows can be operated when (power type)

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

■Operating the windows after turning the engine off (power type)

Vehicles without a smart key system The power type windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, however, be operated once either front door is opened. Vehicles with a smart key system The power type windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.

CAUTION

■Closing the windows

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●Do not allow children to operate the power windows.

Closing a power window on someone can cause serious injury, and in some instances, even death.

150

SIENNA_OM_OM45483U_(U)

1

1-4. Opening and closing the windows and moon roof Moon roof

Use the overhead switches to open and close the moon roof. ■ Front moon roof

Opens the moon roof* The moon roof will stop at the tilt up position once. To tilt down, press the opposite side of the switch. Press open. Closes the moon roof* *: Lightly press either of the roof switches to stop the moon roof partway.

the switch again

to

: If equipped 151

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

■ Rear moon roof (if equipped)

Opens the moon roof* The moon just roof stops before it is opened fully. Press the switch again to open fully. Closes the moon roof* *: Lightly press either of the roof switches to stop the moon roof partway.

Canceling the rear moon roof operation (vehicles with the rear moon roof)

Press the switch to disable the rear moon roof operation from the rear seat.

Pressing the switch again will enable the operation again.

152

SIENNA_OM_OM45483U_(U)

1

1-4. Opening and closing the windows and moon roof

■The moon roof can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

■Operating the moon roof after turning the engine off

Vehicles without a smart key system The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened. Vehicles with a smart key system The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.

■Jam protection function

If an object is detected between the moon roof and the frame while the moon roof is closing, travel is stopped and the moon roof opens slightly.

153

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

■Sunshade

The sunshade can be opened and closed manually. However, both front and rear sunshades open automatically when the moon roof is opened.

■When the moon roof does not close normally

STEP 1

STEP 2

STEP 3

Stop the vehicle. Press and hold the close switch.* The moon roof will start moving after pausing for about 10 seconds. Continue to hold the switch. Release the button when the moon roof stops moving. Within 4 seconds, press and hold the close switch again. Continue to hold the switch as the moon roof opens and closes. Release the close switch when the moon roof completely stops.

STEP 4
*: If the switch is released at the incorrect time, the procedure will have to be

performed again from the beginning.

154

SIENNA_OM_OM45483U_(U)

1-4. Opening and closing the windows and moon roof

CAUTION

■Opening the moon roof

Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-

cle while it is moving.

●Do not sit on top of the moon roof.

■Closing the moon roof

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where it could be caught when the moon roof is being operated.

●Do not allow children to operate the moon roof.

Closing the moon roof on someone can cause death or serious injury.

■Jam protection function

●Never use any part of your body intentionally to activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the moon roof fully closes.

155

SIENNA_OM_OM45483U_(U)

1-5. Refueling Opening the fuel tank cap

Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle

Vehicles without a smart key system Turn the engine switch off and ensure that all the doors and win- dows are closed. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed.

■ Opening the fuel tank cap STEP 1

Pull up the opener to open the fuel filler door.

STEP 2

Turn the fuel tank cap slowly to open.

156

SIENNA_OM_OM45483U_(U)

1-5. Refueling

STEP 3

Hang the fuel tank cap on the back of the fuel filler door.

Closing the fuel tank cap

After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.

■Fuel type

Use unleaded gasoline (Octane rating 87 [Research Octane Number 91] or higher)

■Fuel tank capacity (reference)

20.9 gal. (79 L, 17.4 Imp.gal.)

157

SIENNA_OM_OM45483U_(U)

1-5. Refueling

CAUTION

■When refueling the vehicle

Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.

●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury.

●Do not allow anyone that has not discharged static electricity from their

body to come close to an open fuel tank.

●Do not inhale vaporized fuel.

Fuel contains substances that are harmful if inhaled.

●Do not smoke while refueling the vehicle.

Doing so may cause the fuel to ignite and cause a fire.

●Do not return to the vehicle or touch any person or object that is statically

charged. This may cause static electricity to build up, resulting in a possible ignition hazard.

158

SIENNA_OM_OM45483U_(U)

1

1-5. Refueling

CAUTION

■When refueling

Securely insert the fuel nozzle into the fuel filler neck. If fuel is added with the nozzle slightly lifted away from the fuel filler neck, the automatic shut off function may not operate, resulting in fuel overflowing from the tank.

■When replacing the fuel cap

Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.

NOTICE

■Refueling

Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface.

159

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system Engine immobilizer system

The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.

Vehicles without a smart key system The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed. Vehicles with a smart key system The indicator light flashes after the “ENGINE START STOP” switch has been turned off to indicate that the system is operating. The indicator light stops flash- ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled.

: If equipped

160

SIENNA_OM_OM45483U_(U)

1

1-6. Theft deterrent system

■System maintenance

The vehicle has a maintenance-free type engine immobilizer system.

■Conditions that may cause the system to malfunction

●If the grip portion of the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system

(key with a built-in transponder chip) of another vehicle

■Certifications for the engine immobilizer system

U.S.A. Vehicles without a smart key system FCC ID: WRKRI-34BTY Vehicles with a smart key system FCC ID: NI4TMIMB-1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada This device complies with Industry Canada licence-exempt RSS stan- dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.

161

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system

CAUTION

■Certifications for the immobilizer system

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE

■To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.

162

SIENNA_OM_OM45483U_(U)

1

1-6. Theft deterrent system Alarm

The system sounds the alarm and flashes the lights when forced entry is detected. ■ Triggering of the alarm

The alarm is triggered in the following situations when the alarm is set: ● A locked door is unlocked or opened in any way other than using the entry function (vehicles with a smart key system) or wireless remote control. (The doors will lock again automati- cally.)

● The hood is opened.

■ Setting the alarm system

Close the doors and hood, and lock all the doors using the entry function or wireless remote control. The system will be set automatically after 30 seconds.

indicator

light changes The from being on to flashing when the system is set.

: If equipped 163

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system

■ Deactivating or stopping the alarm

Do one of the following to deactivate or stop the alarm: ● Unlock the doors using the entry function or wireless remote

control.

● Vehicles without a smart key system: Turn the engine switch

to the “ACC” or “ON” position, or start the engine. Vehicles with a smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY or IGNITION ON mode, or start the engine. (The alarm will be deactivated or stopped after a few sec- onds.)

■System maintenance

The vehicle has a maintenance-free type alarm system.

■Items to check before locking the vehicle

To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ●Nobody is in the vehicle. ●The windows and moon roof (if equipped) are closed before the alarm is

set.

●No valuables or other personal items are left in the vehicle.

164

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system

■Triggering of the alarm

The alarm may be triggered in the following situations. (Stopping the alarm deactivates the alarm system.)

●The doors are unlocked using the key.

●A person inside the vehicle opens a

door or hood.

●The battery is recharged or replaced

when the vehicle is locked.

■Alarm-operated door lock

●When the alarm is operating, the doors are locked automatically to pre-

vent intruders.

●Do not leave the key inside the vehicle when the alarm is operating, and make sure the key is not inside the vehicle when recharging or replacing the battery.

165

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system

NOTICE

■To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.

166

SIENNA_OM_OM45483U_(U)

1-6. Theft deterrent system Theft prevention labels (for U.S.A.)

These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.

167

SIENNA_OM_OM45483U_(U)

1-7. Safety information Correct driving posture

Drive with a good posture as follows:

and to

Sit upright and well back in the seat. (P. 95) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed the extent required. (P.95) Adjust the seatback so that the controls are easily oper- able. (P.95) Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (P.138) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (P.126) Wear the seat belt correctly. (P.129)

168

SIENNA_OM_OM45483U_(U)

1

1-7. Safety information

CAUTION

■While driving

●Do not adjust the position of the driver’s seat.

Doing so could cause the driver to lose control of the vehicle.

●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.

●Do not place anything under the front seats except for putting them in the

auxiliary box. Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent, resulting in death or serious injury. The adjustment mechanism may also be damaged.

■Adjusting the seat position

●Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

●Do not put your hands under the seat or near the moving parts to avoid

injury. Fingers or hands may become jammed in the seat mechanism.

169

SIENNA_OM_OM45483U_(U)

1-7. Safety information SRS airbags

The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.

170

SIENNA_OM_OM45483U_(U)

1

1-7. Safety information

SRS front airbags

SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components. SRS driver knee airbag Can help provide driver protection. SRS side and curtain shield airbags

SRS side airbags Can help protect the torsos of the front seat occupants. SRS curtain shield airbags Can help protect primarily the heads of occupants in the outer seats.

171

SIENNA_OM_OM45483U_(U)

1-7. Safety information

Airbag system components

Front passenger airbag Curtain shield airbags Side airbags Front passenger occupant classification system (ECU and sensors) Side impact sensors (rear) Front passenger’s seat belt buckle switch SRS warning light Driver airbag

Side impact sensors (front door) Driver’s seat belt buckle switch Driver’s seat position sen- sor Driver’s knee airbag Front impact sensors Airbag sensor assembly “AIR BAG ON” and “AIR BAG OFF” indicator lights Seat belt pretensioners

172

SIENNA_OM_OM45483U_(U)

1

1-7. Safety information

Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with nontoxic gas to help restrain the motion of the occupants.

173

SIENNA_OM_OM45483U_(U)

1-7. Safety information

■If the SRS airbags deploy (inflate)

●Bruising and slight abrasions may result from contact with a deploying

(inflating) SRS airbag.

●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rail, may be hot for several minutes. The airbag itself may also be hot.

●The windshield may crack. ●For Safety Connect subscribers, if the SRS airbags deploy or in the event of a severe rear-end collision, the system is designed to send an emer- gency call to the response center, notifying them of the vehicle’s location (without needing to push the “SOS” button) and an agent will attempt to speak with the occupants to ascertain the level of emergency and assis- tance required. If the occupants are unable to communicate, the agent automatically treats the call as an emergency and helps to dispatch the necessary emergency services. (P.639)

174

SIENNA_OM_OM45483U_(U)

1-7. Safety information

■SRS airbag deployment conditions (SRS front airbags)

●The SRS front airbag will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher in the following situations: • If the vehicle strikes an object, such as a parked vehicle or sign pole,

which can move or deform on impact

• If the vehicle is involved in an underride collision, such as a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck

●Depending on the type of collision, it is possible that only the seat belt

pretensioners will activate.

●The SRS front airbags for the front passenger will not activate if there is no passenger sitting in the front passenger seat. However, the SRS front airbags for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied.

■SRS airbag deployment conditions (SRS side and curtain shield air-

bags) ●The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corre- sponding to the impact force produced by an approximately 3300 lb. [1500 kg] vehicle colliding with the vehicle cabin from a direction perpen- dicular to the vehicle orientation at an approximate speed of 12 - 18 mph [20 - 30 km/h]).

●The SRS curtain shield airbags may also deploy in the event of a severe

frontal collision.

175

SIENNA_OM_OM45483U_(U)

1-7. Safety information

■Conditions under which the SRS airbags may deploy (inflate), other

than a collision The SRS front airbags and curtain shield airbags may also deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

●Hitting a curb, edge of pavement or

hard surface

●Falling into or jumping over a deep hole ●Landing hard or falling

■Types of collisions that may not deploy the SRS front airbag (SRS front

airbags) The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, deployment of the SRS front airbags may occur.

●Collision from the side ●Collision from the rear ●Vehicle rollover

176

SIENNA_OM_OM45483U_(U)

1

1-7. Safety information

■Types of collisions that may not deploy the SRS airbags (SRS side and

curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.

●Collision from the side to the vehicle body other than the passenger com- partment

●Collision from the side at an angle

The SRS side airbags do not generally inflate if the vehicle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low-speed side collision.

●Collision from the front ●Collision from the rear ●Vehicle rollover

The SRS curtain shield airbags do not generally inflate if the vehicle is involved in a rear collision, if it rolls over, or if it is involved in a low-speed side collision.

●Collision from the rear ●Vehicle rollover

177

SIENNA_OM_OM45483U_(U)

1-7. Safety information

■When to contact your Toyota dealer

In the following cases, contact your Toyota dealer as soon as possible. ●Any of the SRS airbags have been inflated.

●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS front airbags to inflate.

●A portion of a door or it’s surrounding area is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield air- bags to inflate.

●The pad section of the steering wheel, dashboard near the front passenger air- bag or lower portion of the instrument panel is scratched, cracked, or other- wise damaged.

●The surface of the seats with the side