2012 Toyota Sienna Owners Manual

The audio system can be turned off by holding the switch down until you hear a beep.

Changing the audio source

Press when the audio system is turned on. The audio source changes as follows each time the button is pressed. If a mode cannot be used, it will be skipped. Type A: FM (1, 2) → CD player → AUX → AM → SAT (1, 2, 3) Type B and C: FM → SAT → CD player (type B) or CD changer (type C) → RSE* → Bluetooth® audio → AUX → iPod or USB memory → AM *: If equipped

Adjusting the volume

Press “+” on volume.

to increase the volume and “-” to decrease the

Hold down the button to continue increasing or decreasing the volume.

464

SIENNA_U (OM45477U)

3-2. Using the audio system

Selecting a radio station

STEP 1

Press

to select the radio mode.

STEP 2

Press “∧” or “∨” on

to select a radio station.

To scan for receivable stations, press and hold the switch until you hear a beep.

Selecting a track/file or song

STEP 1

Press USB memory mode.

to select CD, RSE, Bluetooth® audio, iPod or

STEP 2

Press “∧” or “∨” on song.

Selecting an album

to select the desired track/file or

STEP 1

Press

to select Bluetooth® audio mode.

STEP 2

Press and hold “∧” or “∨” on

until you hear a beep.

Selecting a folder

STEP 1

Press

to select USB memory mode.

STEP 2

Press and hold “∧” or “∨” on

until you hear a beep.

465

SIENNA_U (OM45477U)

3-2. Using the audio system

Selecting a disc in the CD changer (type C only)

STEP 1

Press

to select the CD mode.

STEP 2

Press and hold “∧” or “∨” on

until you hear a beep.

Selecting a track/file or chapter (vehicles with rear seat entertainment system)

STEP 1

Press

to select the RSE mode.

STEP 2

Press “∧” or “∨” on chapter.

to select the desired track/file or

■Canceling automatic selection of a radio station

Press

again.

CAUTION

■To reduce the risk of an accident

Exercise care when operating the audio switches on the steering wheel.

466

SIENNA_U (OM45477U)

3-2. Using the audio system Detachable pole antenna∗

The antenna can be removed. ■ Removing the antenna STEP 1

the

Place around the antenna.

included wrench

When not in use, the wrench is stored in glove box.

STEP 2

Loosen the antenna with the wrench and remove it.

∗: If equipped 467

SIENNA_U (OM45477U)

3-2. Using the audio system

■ Installing the antenna STEP 1

STEP 2

Tighten the antenna by one hand until it will not turn any more.

Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place.

After tightening the antenna, remove the wrench.

■About the wrench

After using the included wrench, store it in the glove box for safekeeping.

468

SIENNA_U (OM45477U)

3-2. Using the audio system

NOTICE

■To avoid damaging the antenna

Remove the antenna in the following situations. ●When using an automatic carwash. ●When the antenna will touch the ceiling of a garage, etc. ●When covering the vehicle with a car cover.

■Removing the antenna

●For normal driving, make sure the antenna is installed. ●When removing the antenna to use an automatic carwash, etc., be careful not to lose the antenna. Also, make sure to reinstall the antenna before driving the vehicle.

■Using the wrench

●When installing or removing the antenna, use the included wrench. ●Be careful not to scratch or damage the vehicle body with the wrench. ●Do not over-tighten the antenna.

Over-tightening may damage the antenna.

●Do not use any tools other than the included wrench to install or remove

the antenna. Otherwise damage may result on the antenna’s finish.

469

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system Bluetooth® audio system∗

The Bluetooth® audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. This audio system supports Bluetooth®, a wireless data system capable of playing portable audio music without cables. If your por- table player does not support Bluetooth®, the Bluetooth® audio sys- tem will not function. Vehicles with a navigation system

Owners of models equipped with a navigation system should refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.

Vehicles without a navigation system

Title

Using the Bluetooth® audio system Operating a Bluetooth® enabled portable player Setting up a Bluetooth® enabled portable player Bluetooth® audio system setup

Page P. 474
P. 480
P. 482
P. 487

∗: If equipped

470

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

■Conditions under which the system will not operate

●If using a portable player that does not support Bluetooth® ●If the portable player is switched off ●If the portable player is not connected ●If the portable player’s battery is low ●If the portable player is behind the seat or in the glove box or console box ●If metal is covering or touching the portable player

■When transferring ownership of the vehicle

Be sure to initialize the system to prevent personal data from being improp- erly accessed. (→P. 557)

■About Bluetooth®

Bluetooth is a registered trademark of Bluetooth SIG. Inc.

471

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

■Compatible models

●Bluetooth® specifications:

Ver. 1.2, or higher (Recommended: Ver. 2.0+EDR or higher)

●Following Profiles:

• A2DP (Advanced Audio Distribution Profile) Ver. 1.0 or higher • AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher (Ver. 1.3 or higher recommended)

Portable players must correspond to the above specifications in order to be connected to the Bluetooth® audio system. However, please note that some functions may be limited depending on the type of portable player.

■Certification for the Bluetooth® audio system

FCC ID: AJDK025 IC ID: 775E-K025
MADE IN THAILAND This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired oper- ation.

472

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

CAUTION

■FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply with- out maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 7.9 in. (20 cm) and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

■While driving

Do not connect portable players or operate the controls.

NOTICE

■To prevent damage to portable players

Do not leave portable players in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the player.

473

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system Using the Bluetooth® audio system

■ Audio unit

Display A message, name, number, etc. is displayed. Lower-case characters and special characters cannot be displayed.

Selects items such as menu and number Turn: Selects an item Press: Inputs the selected item Bluetooth® connection con- dition

If “BT” is not displayed, the Bluetooth® audio sys- tem cannot be used.

■ Microphone

474

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Operating the system using voice commands

By following voice guidance instructions output from the speaker, voice commands enable to the operation of the Bluetooth® audio sys-

tem without the need to check the display or operate

■ Operation procedure when using voice commands

Press the talk switch and follow voice guidance instructions.

■ Auxiliary commands when using voice commands

The following auxiliary commands can be used when operating the system using a voice command: Cancel: Exits the Bluetooth® audio system Repeat: Repeats the previous voice guidance instruction Go back: Returns to the previous procedure Help: Reads aloud the function summary if a help comment is registered for the selected function

475

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Using the Bluetooth® audio system for the first time

Before using the Bluetooth® audio system, it is necessary to register a Bluetooth® enabled portable player in the system. Follow the proce- dure below to register (pair) a portable player:

STEP 1

Press

until “BT AUDIO” is displayed.

STEP 2

Press

that corresponds to “SETUP”.

The introductory guidance and portable player name registration instructions are heard.

STEP 3

Select “Pair Audio Player (Pair Audio)” using a voice com-

mand or

STEP 4

Register a portable player name by either of the following methods:

a. Select “Record Name” using

, and say the name to

be registered.

b. Press the talk switch and say the name to be registered.

A voice guidance instruction to confirm the input is heard.

476

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

STEP 5

Select “Confirm” using a voice command or

A passkey is displayed and heard, and a voice guidance instruction for inputting the passkey into the portable player is heard. STEP 6

Input the passkey into the portable player. Refer to the manual that comes with the portable player for the oper- ation of the portable player.

Guidance for registration completion is heard. If the portable player has a Bluetooth® phone, the phone can be reg- istered at the same time. (→P. 537)

477

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Menu list of the Bluetooth® audio system

■ Normal operation

First menu

Second menu

“BT•A Setup”

“Setup”

“System Setup”*

Third menu

Operation detail

“Pair Audio Player” “Select Audio Player”

“Change Name”

“List Audio Play- ers” “Set Passkey”

“Delete Audio”

“Guidance Vol- ume”

“Device Name”

“Initialize”

Registering a portable player

Selecting a portable player to be used Changing the registered name of a portable player Listing the registered porta- ble players Changing the passkey Deleting a registered porta- ble player Setting voice guidance vol- ume Displaying the Bluetooth® device address and name Initializing the system

“BT•A Setup” can be canceled by pressing the on-hook switch or saying the voice command, “Cancel”. *: Selection of system set-up is possible only by the operation of

the steering wheel switch.

478

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

■When using a voice command

For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly.

■Situations in which the system may not recognize your voice

●When driving on rough roads ●When driving at high speeds ●When air is blowing out of the vents onto the microphone ●When the air conditioning fan emits a loud noise

■Operations that cannot be performed while driving

●Operating the system with

●Registering a portable player to the system

■Changing the passkey

→P. 485

479

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system Operating a Bluetooth® enabled portable player

Power

Volume

Selecting a track/ fast-forwarding and reversing

Selecting an album

Selector buttons

Playback/pause

Displaying text messages

Playback

Selecting an album

Press “∧” or “∨” on

Selecting tracks

Press “∧” or “∨” on

to select the desired track.

480

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Playing and pausing tracks

Press

Fast-forwarding and rewinding tracks

Press and hold “∧” or “∨” on

Switching the display

Press

Each time the button is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time

Using the steering wheel audio switches

→P. 463

■Bluetooth® audio system functions

Depending on the portable player that is connected to the system, certain functions may not be available.

481

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system Setting up a Bluetooth® enabled portable player

Registering a portable player in the Bluetooth® audio system allows the system to function. The following functions can be used for reg- istered portable players: ■ Functions and operation procedures

STEP 1

Press

until “BT AUDIO” is displayed.

STEP 2

STEP 3

that corresponds to “SETUP”

Press Select one of the following functions using a voice com-

mand or

● Registering a portable player

“Pair Audio Player”

● Selecting a portable player to be used

“Select Audio Player”

● Changing the registered name

“Change Name”

● Listing the registered portable players

“List Audio Players”

● Changing the passkey

“Set Passkey”

● Deleting a registered portable player

“Delete Audio Player”

482

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Registering a portable player

Select “Pair Audio Player” using a voice command or perform the procedure for registering a portable player. (→P. 476)

, and

Selecting a portable player to be used

STEP 1

Select “Select Audio Player” using a voice command or

STEP 2

Select the portable player to be used by either of the following methods, and select “Confirm” by using a voice command or

a. Press the talk switch and say the name of the desired por-

table player.

b. Press the talk switch and say “List Audio Players”. When the name of the desired portable player is read aloud, press the talk switch.

STEP 3

Press the talk switch and say “From Car” or “From Audio”, and

select “Confirm” by using a voice command or

483

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Vehicles without a smart key system When the portable player is on standby for the connection, it will be automatically connected whenever the engine switch is in either “ACC” or “ON” position. If a portable player that has already been paired is selected, it is nec- essary to select “From Car” or “From audio” setting. Vehicles with a smart key system When the portable player is on standby for the connection, it will be automatically connected whenever the “ENGINE START STOP” switch is in either ACCESSORY or IGNITION ON position. If a portable player that has already been paired is selected, it is nec- essary to select “From Car” or “From audio” setting.

Changing the registered name of a portable player

STEP 1

Select “Change Name” using a voice command or

STEP 2

Select the name of the portable player to be changed by either of the following methods, and select “Confirm” using a

voice command or

a. Press the talk switch and say the name of the desired por-

table player.

b. Press the talk switch and say “List Audio Players”. When the name of the desired portable player is read aloud, press the talk switch.

STEP 3

Press the talk switch or select “Record Name” using and say the new name.

STEP 4

Select “Confirm” using a voice command or

484

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Listing the registered portable players

. The list

Select “List Audio Players” using a voice command or of registered portable players will be read aloud. When listing is complete, the system returns to “BT•A Setup”. Pressing the talk switch while the name of a portable player is being read aloud selects the portable player, and the following functions will become available: ● Selecting a portable player: “Select Audio Player” ● Changing a registered name: “Change Name” ● Deleting a portable player: “Delete Audio Player”

Changing the passkey

STEP 1

Select “Set Passkey” using a voice command or

STEP 2

Press the talk switch, say a 4 to 8-digit number, and select

“Confirm” using a voice command or

STEP 3

When the entire number to be registered as a passkey has

been input, press

again.

If the number to be registered has 8 digits, pressing of the knob is not necessary.

485

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system

Deleting a registered portable player

STEP 1

Select “Delete Audio Player” using a voice command or

STEP 2

Select the portable player to be deleted by either of the follow- ing methods and select “Confirm” using a voice command or

a. Press the talk switch and say the name of the desired por-

table player.

b. Press the talk switch and say “List Audio Players”. When the name of the desired portable player is read aloud, press the talk switch.

If the portable player to be deleted is paired as a Bluetooth® phone, the registration of the mobile phone can be deleted at the same time. A voice guidance instruction to delete a mobile phone is heard.

STEP 3

Select “Confirm” by using a voice command or

■The number of portable players that can be registered Up to 2 portable players can be registered in the system.

486

SIENNA_U (OM45477U)

3-3. Using the Bluetooth® audio system Bluetooth® audio system setup

■ System setup items and operation procedures

→P. 553

487

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone) Hands-free phone system (for cellular phone) features∗

The hands-free system is a function that allows you to use your cel- lular phone without touching it. This system supports Bluetooth®, which allows you to make or receive calls without using cables to connect a cellular phone to the system, and without operating the cellular phone. With navigation system Owners of models equipped with a navigation system should refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”. Without navigation system ■ Hands-free system quick guide STEP 1

Setting a cellular phone. (→P. 534) Adding an entry to the phonebook (Up to 20 names can be stored). (→P. 558) Dialing by inputting a name. (→P. 544)

STEP 2

STEP 3

∗: If equipped 529

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Title

Using the hands-free phone system ■ Operating the system using a voice

■ Using the hands-free phone system for

■ Menu list of the hands-free phone sys-

command

the first time

tem

Making a phone call ■ Dialing by inputting a number ■ Dialing by inputting a name ■ Speed dialing ■ When receiving a phone call ■ Transferring a call ■ Using the call history memory Setting a cellular phone ■ Registering a cellular phone ■ Selecting the cellular phone to be used ■ Changing a registered name ■ Listing the registered cellular phone ■ Deleting a cellular phone ■ Changing the passkey ■ Turning the hands-free phone auto-

matic connection on/off Security and system setup ■ Setting or changing the PIN ■ Locking or unlocking the phone book ■ Setting voice guidance volume ■ Initialization Using the phone book ■ Adding a new phone number ■ Setting speed dials ■ Changing a registered name ■ Deleting registered data ■ Deleting speed dials ■ Listing the registered data

530

SIENNA_U (OM45477U)

Page

P. 534

P. 543

P. 548

P. 553

P. 558

3-5. Using the hands-free phone system (for cellular phone)

■Conditions under which the system will not operate

●If using a mobile phone that does not support Bluetooth® ●If the mobile phone is switched off ●If you are outside service range ●If the mobile phone is not connected ●If the mobile phone’s battery is low ●If the mobile phone is behind the seat or in the glove box or console box ●If metal is covering or touching the phone

■When using the hands-free system

●The audio system and voice guidance are muted when making a call. ●If both parties speak at the same time, it may be difficult to hear. ●If the incoming call volume is overly loud, an echo may be heard. ●Try to face toward the microphone as much as possible when speaking. ●In the following circumstances, it may be difficult to hear the other party:

• When driving on unpaved roads • When driving at high speeds • When a window is open • When the air conditioning is blowing directly on the microphone • When the air conditioning is set to high

■When transferring ownership of the vehicle

Be sure to initialize the system to prevent personal data from being improp- erly accessed.

531

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

■About Bluetooth®

Bluetooth is a registered trademark of Bluetooth SIG. Inc.

■Compatible models

Compatible with HFP (Hands Free Profile) Ver. 1.5 and OPP (Object Push Profile) Ver. 1.1. If your cellular phone does not support HFP, you cannot enter the Bluetooth® phone. If your cellular phone supports OPP alone, you cannot use the Bluetooth® phone.

■Certification for the hands-free phone system

FCC ID: AJDK025 IC ID: 775E-K025
MADE IN THAILAND This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired oper- ation.

532

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

CAUTION

■FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply with- out maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 7.9 in. (20 cm) and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

■Caution while driving

Do not use a cellular phone, or connect the Bluetooth® phone.

NOTICE

■To prevent damage to a cellular phone

Do not leave a cellular phone in the vehicle. The temperature inside may become high resulting in damage to the phone.

533

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone) Using the hands-free phone system (for cellular phone)∗

■ Audio unit

Displays such messages, phone number

items as and

name,

Lower-case characters and special characters, such as an umlaut, cannot be dis- played.

Selects items such as menu or number Turn: Selects an item Press: Inputs the selected item Selects speed dials Bluetooth® connection con- dition and reception level

If “BT” is not displayed, the hands-free phone system cannot be used.

∗: If equipped

534

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

■ Steering wheel telephone switches

Volume

The voice guidance volume cannot be adjusted using this button.

Hands-free phone system off/ends a call/refuses a call Hands-free phone system on/starts a call Press: Voice command sys- tem on Press and hold: Voice com- mand system off

■ Microphone

535

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Operating the system using a voice command

By following voice guidance instructions output from the speaker, voice commands can be given to allow for operation of the hands-

free phone system without checking the display or operating

■ Operation procedure when using a voice command

Press the talk switch and follow voice guidance instructions.

■ Auxiliary commands when using a voice command

The following auxiliary commands can be used when operating the system using a voice command: Cancel: Exits the hands-free phone system Repeat: Repeats the previous voice guidance instruction Go back: Returns to the previous procedure Help: Reads aloud the function summary if a help comment is registered for the selected function

536

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Using the hands-free phone system for the first time

Before using the hands-free phone system, it is necessary to register a cellular phone in the system. The phone registration mode will be entered automatically when starting the system with no cellular phone registered. Follow the procedure below to register a cellular phone: STEP 1
The introductory guidance and phone name registration instructions are heard.

Press off-hook switch or talk switch.

STEP 2

Select “Pair Phone” using a voice command or

STEP 3

Register a phone name by either of the following methods.

a. Select “Record Name” using

, and say a name to be

registered.

b. Press the talk switch and say a name to be registered.

A voice guidance instruction to confirm the input is heard.

STEP 4

Select “Confirm” using a voice command or

537

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Registration to the hands-free phone system only

STEP 5

Select “Phone Only” using a voice command or

Registration to the hands-free phone system and Bluetooth® audio system at the same time STEP 5

Select “Internal Audio (Int, Audio)” using a voice command or

Select “Confirm” by using a voice command or

STEP 6
A passkey is displayed and heard, and a voice guidance instruction for inputting the passkey into the cellular phone is heard. STEP 7

Input the passkey into the cellular phone. Refer to the manual that comes with the cellular phone for the oper- ation of the phone.

Guidance for registration completion is heard.

538

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Menu list of the hands-free phone system

■ Normal operation

First menu

Second menu

Third menu

Operation detail

“Callback”

“Redial”

“Dial by number” “Dial by name”

“Phone- book”

“Add Entry” “Change Name” “Delete Entry” “Delete Speed Dial (Del Spd Dial)” “List Names” “Set Speed Dial (Speed Dial)”

Dialing a number stored in the incoming call history memory Dialing a number stored in the outgoing call history memory

Dialing by inputting a number

Dialing by inputting a name registered in the phone book

Adding a new number

Changing a name in the phone book

Deleting the phone book data

Deleting a registered speed dial

Listing the phone book data

Registering a speed dial

539

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

First menu

Second menu

Third menu

Operation detail

“Security”

“Setup”

“Phone Setup”

“System Setup”

“Set PIN” “Phonebook Lock” “Phonebook Unlock”

“Pair Phone”

“Change Name”

“Delete Phone”

“List Phones”

“Select Phone”

“Set Passkey” “Hands-free power” “Guidance Vol- ume” “Device Name” “Initialize”

Setting a PIN code

Locking the phone book

Unlocking the phone book

Registering the cellular phone to be used Changing a registered name of a cellular phone Deleting a registered cellular phone Listing the registered cellular phones Selecting a cellular phone to be used Changing the passkey Setting the hands-free power on/off Setting voice guidance vol- ume Displaying device information Initialization

540

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

■ Using a short cut key

First menu

Second menu

Operation detail

“Dial XXX (name)”

“Dial XXX (number)” “Phone book add entry”

“Phone book change name”

“Phone book delete entry” “Phone book set speed dial” “Phone book delete speed dial”

“Phonebook”

“Phone book list names”

Dialing a number registered in the phone book Dialing the input numbers

Adding a new number

Changing the name of a phone number in the phone book

Deleting phone book data

Registering a speed dial

Deleting a speed dial

“Phonebook Unlock” Unlocking the phone book “Phonebook Lock”

Locking the phone book

Listing the phone book data

541

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

■Automatic adjustment of volume

When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less.

■When using a voice command

●For numbers, say a combination of single digits from zero to nine, #

(pound), ∗ (star), and + (plus).

●Say a command correctly and clearly.

■The system may not recognize your voice in the following situations:

●When driving on a rough road ●When driving at high speeds ●When air is blowing out of the vents onto the microphone ●When the air conditioning fan emits a loud noise

■The following cannot be performed while driving:

●Operating the system with

●Registering a cellular phone to the system

■Changing the passkey

→P. 552

542

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone) Making a phone call

■ Making a phone call

● Dialing by inputting a number

“Dial by number”

● Dialing by inputting a name

“Dial by name” ● Speed dialing ● Dialing a number stored in the outgoing history memory

“Redial”

● Dialing a number stored in the incoming history memory

“Call back”

■ Receiving a phone call ● Answering the phone ● Refusing the call ■ Transferring a call ■ Using the call history memory

● Dialing ● Storing data in the phone book ● Deleting

SIENNA_U (OM45477U)

543

3-5. Using the hands-free phone system (for cellular phone)

Dialing by inputting a number

STEP 1

STEP 2

STEP 3

Press the talk switch and say “Dial by number”. Press the talk switch and say the phone number. Dial by one of the following methods: a. Press the off- hook switch. b. Press the talk switch and say “Dial”.

c. Select “Dial” using

Dialing by inputting a name

STEP 1

STEP 2

Press the talk switch and say “Dial by name”. Select a registered name to be input by either of the following methods: a. Press the talk switch and say a registered name. b. Press the talk switch and say “List names”. Press the talk

switch while the desired name is being read aloud.

STEP 3

Dial by one of the following methods: a. Press the off-hook switch. b. Press the talk switch and say “Dial”.

c. Select “Dial” using

544

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Speed dialing

STEP 1

STEP 2

STEP 3

Press the off-hook switch. Press the preset button in which the desired number is regis- tered. Press the off-hook switch.

When receiving a phone call

■ Answering the phone

Press the off-hook switch.

■ Refusing the call

Press the on-hook switch.

Transferring a call

A call can be transferred between the cellular phone and system while dialing or receiving a call, or during a call. Use one of the follow- ing methods:

a. Operate the cellular phone.

Refer to the manual that comes with the cellular phone for the oper- ation of the phone.

b. Press the off-hook switch*1. c. Press the talk switch and say “Call Transfer”*2. *1: This operation can be performed only when transferring a call

from the cellular phone to the system during a call.

*2: While the vehicle is in motion, a call cannot be transferred

from the system to the cellular phone.

545

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Using the call history memory

Follow the procedure below to use a number stored in the call history memory:

STEP 1

STEP 2

Press the talk switch and say “Redial” (when using a number stored in the outgoing call history memory) or “Call back” (when using a number stored in the incoming call history memory). Select the number by either of the following methods: a. Say “Previous” or “Go back” until the desired number is dis-

played.

b. Select the desired number using

The following operations can be performed:

Dialing: Press the off-hook switch or select “Dial” using a voice

command or

Storing the number in the phone book: Select “Store” using a voice

command or

Deleting: Select “Delete” using a voice command or

546

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

■Call history

Up to 5 phone numbers can be stored in each of the outgoing and incoming call history memories.

■When talking on the phone

●Do not talk simultaneously with the other party. ●Keep the volume of the received voice down. Otherwise, voice echo will

increase.

547

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone) Setting a cellular phone

Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below using a

voice command or

● Registering a cellular phone

1. “Setup” → 2. “Phone Setup” → 3. “Pair Phone”

● Selecting the cellular phone to be used

1. “Setup” → 2. “Phone Setup” → 3. “Select Phone”

● Changing a registered name

1. “Setup” → 2. “Phone Setup” → 3. “Change Name”

● Listing the registered cellular phones

1. “Setup” → 2. “Phone Setup” → 3. “List Phones”

● Deleting a cellular phone

1. “Setup” → 2. “Phone Setup” → 3. “Delete Phone”

● Changing the passkey

1. “Setup” → 2. “Phone Setup” → 3. “Set Passkey”

● Turning the hands-free phone automatic connection on/off

1. “Setup” → 2. “Phone Setup” → 3. “Hands-free power”

548

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Registering a cellular phone

Select “Pair Phone” using a voice command or procedure for registering a cellular phone. (→P. 537)

, and do the

Selecting the cellular phone to be used

STEP 1

Select “Select Phone” using a voice command or

Pattern A STEP 2

Select the cellular phone to be used by either of the following methods, and select “Confirm” using a voice command or

a. Press the talk switch and say the desired phone name. b. Press the talk switch and say “List phones”. While the name of the desired cellular phone is being read aloud, press the talk switch.

Pattern B STEP 2

Select the cellular phone to be used using

549

SIENNA_U (OM45477U)

3-5. Using the hands-free phone system (for cellular phone)

Changing a registered name

STEP 1

Select “Change Name” using a voice command or

STEP 2

Select the name of the cellular phone to be changed by one of the following methods: a. Press the talk switch and say the desired phone name, and

select “Confirm” using a voice command or

b. Press the talk switch and say “List phones”. While the desired phone name is being read aloud, press the talk switch.

c. Select the desired phone name using

STEP 3

Press the talk switch or select “Record Name” using and say a new name.

STEP 4

Select “Confirm” using a voice command or