2012 Toyota Sienna Owners Manual

●Interference from other radio waves may cause the AUTO ACCESS SEAT to stop moving temporarily even when pressing the wireless remote control switches. In this event, do the following: • Stand in a different place and press the switch.

Press the switch once again after moving. The AUTO ACCESS SEAT will not operate if you hold the switch down while changing position.

• Operate the seat raise/lower switch (→P. 35)

■Battery

●The lifespan of the battery is about 6 months, but this may change in

accordance with usage.

●If the battery is discharged, the AUTO ACCESS SEAT may not operate even if the wireless remote control is operated or the indicator light will stop flashing. In these events, replace the battery with a new one. (→P. 40)

■When riding in an aircraft

When bringing a wireless remote control onto an aircraft, make sure you do not press any buttons on the wireless remote control while inside the aircraft cabin. If you are carrying the wireless remote control in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the wireless remote control to emit radio waves that could inter- fere with the operation of the aircraft.

17

SIENNA AAS_U (OM45471U)

1-1. AUTO ACCESS SEAT

■Conditions affecting operation

If you use the wireless remote control to operate the AUTO ACCESS SEAT at the same time as doing any of the following, the AUTO ACCESS SEAT may not operate properly: ●Operating the AUTO ACCESS SEAT using another wireless remote con-

trol

●Operating the AUTO ACCESS SEAT using the seat raise/lower switch ●Using the smart key system ●Unlocking and locking the doors using the wireless remote control

■When replacing either the transmitter or the receiver of the wireless

remote control It is necessary to replace both the transmitter and the receiver. Contact your Toyota dealer.

■Certification for the wireless remote control

U.S.A. FCC ID: HYQ12BDF FCC ID: HYQ13BDH NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

18

SIENNA AAS_U (OM45471U)

1-1. AUTO ACCESS SEAT

CAUTION

■Wireless remote control precautions

Observe the following precautions to reduce the risk of injury. ●Operate the AUTO ACCESS SEAT from a position from which you can

see the occupant of the seat.

●Make sure that the occupant’s head, arms and legs will not get caught

between the seat and the body of the vehicle.

●Steady the AUTO ACCESS SEAT and the occupant with your hand while

operating.

NOTICE

■To prevent wireless remote control damage

●Observe the following:

• Do not expose the wireless remote control to high temperatures by

placing it in direct sunlight.

• Do not disassemble the wireless remote control. • Do not drop the wireless remote control, subject it to strong shocks or

bend it.

• Do not get the wireless remote control wet.

●Do not wipe the wireless remote control with thinner, gasoline or benzene.

The surface of it may be damaged. When cleaning the wireless remote control, wipe it using a wrung cloth soaked in water or lukewarm water.

●Do not attach metallic or magnetic materials to the wireless remote control

or place the wireless remote control close to such materials.

●Do not attach metallic window tinting or other metallic objects such as non-

genuine antenna to the windows.

●Do not attach accessories to the wireless remote control. These could get

caught in the AUTO ACCESS SEAT during operation.

19

SIENNA AAS_U (OM45471U)

1

1-1. Key information

Using the mechanical key (vehicles with a smart key system)

To take out the mechanical key, push the release button and take the key out.

The mechanical key can only be inserted in one direction, as the key only has grooves on one side. If the key cannot be inserted in a lock cylinder, turn it over and re-attempt to insert it. After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery is depleted or the entry function does not operate properly, you will need the mechanical key. (→P. 767)

33

SIENNA_U (OM45477U)

1-1. Key information

■When required to leave the vehicle’s key with a parking attendant

Lock the glove box as circumstances demand. (→P. 573) On vehicles without the smart key system, provide the attendant with the valet key. On vehicles with the smart key system, remove the mechanical key for your own use and provide the attendant with the electronic key only.

■Key number plate

Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key (without a smart key system) or mechanical key (with a smart key system) is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 766)

■When riding in an aircraft

When bringing a key with wireless remote control function onto an aircraft, make sure you do not press any buttons on the key while inside the aircraft cabin. If you are carrying the key in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.

34

SIENNA_U (OM45477U)

1

1-1. Key information

NOTICE

■To prevent key damage

Observe the following: ●Do not drop the keys, subject them to strong shocks or bend them. ●Do not expose the keys to high temperatures for a long periods of time. ●Do not get the keys wet or wash them in an ultrasonic washer etc. ●Do not attach metallic or magnetic materials to the keys or place the keys

close to such materials.

●Do not disassemble the keys. ●Do not attach a sticker or anything else to the surface of the electronic key. ●Do not place the keys near objects that produce magnetic fields, such as TVs, audio systems, glass top ranges, or medical electrical equipment, such as low-frequency therapy equipment.

■Carrying the electronic key on your person (vehicles with a smart key

system) Carry the electronic key 3.9 in. (10 cm) or more away from electric appli- ances that are turned on.

■In case of a smart key system malfunction or other key-related prob-

lems (vehicles with a smart key system) Take your vehicle with all the electronic keys provided with your vehicle to your Toyota dealer.

■When a vehicle key is lost (vehicles with a smart key system)

If the key remains lost, the risk of vehicle theft increases significantly. Visit your Toyota dealer immediately with all remaining electronic keys that were provided with your vehicle.

35

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors Smart key system∗

The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)

Locks and unlocks the doors (→P. 37) Locks and unlocks the doors (→P. 38)

Starts and stops the engine (→P. 229)

∗: If equipped

36

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Unlocking and locking the doors

Front door handles

Grip the handle to unlock all the doors.

Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 seconds after the doors are locked.

the

lock sensor

Touch (the indentation on the upper part of the door handle) to lock all the doors.

Sliding door handles (vehicles with power sliding door)

Pull the handle to unlock all the doors.

There is no touch type sensor in slide door handle. You must pull the handle to activate the opera- tion.

37

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Back door

the unlock button

Press unlock all the doors.

to

the door

The door cannot be unlocked for 3 seconds after is locked. Lock the back door again when you leave the vehicle. The back door will not lock automatically after it has been opened and then closed.

Press the lock button to lock all the doors.

38

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Antenna location and effective range

■ Antenna location

Antennas outside cabin Antennas inside cabin Antenna outside luggage com- partment

39

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■ Effective range (areas within which the electronic key is

detected)

When locking or unlock- ing the doors The system can be oper- ated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front outside door handles. (Only the doors detecting the key can be operated.) When starting the engine or changing “ENGINE START STOP” switch modes The system can be oper- ated when the electronic key is inside the vehicle.

■Operation signals

A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

■When the door cannot be locked by the lock sensor on the upper part

of the front door handle

Touch both lock sensors on the upper and lower part of the front door handle simul- taneously.

40

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■Alarms and warning indicators

A combination of exterior and interior alarms as well as warnings shown on the multi-information display are used to prevent theft of the vehicle and unforeseeable accidents resulting from erroneous operation. Perform the appropriate correction procedure described in the following table.

Alarm

Situation

Correction procedure

An attempt was made to lock the doors using the entry function while the electronic key was still inside the passenger com- partment An attempt was made to exit the vehicle and lock the doors without first turn- ing the “ENGINE START STOP” switch off An attempt was made to lock the vehicle while a door is open

Retrieve the elec- tronic key from the passenger compart- ment and lock the doors again

Turn the “ENGINE START STOP” switch off and lock the doors again

Close all of the doors and lock the doors again

Interior alarm pings once and exterior alarm sounds once for 10 seconds

Exterior alarm sounds once for 10 seconds

41

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Alarm

Situation

Correction procedure

Interior alarm pings continu- ously*1

Interior alarm sounds continu- ously*1

Interior and exte- rior alarms sound continuously*1

The “ENGINE START STOP” switch was turned to ACCESSORY mode while the driver’s door was open (or the driver’s door was opened while the “ENGINE START STOP” switch was in ACCES- SORY mode) When the “ENGINE START STOP” switch is in IGNITION ON or ACCES- SORY mode, an attempt was made to open the door and exit the vehicle, and the shift lever was not in “P” When the “ENGINE START STOP” switch is in IGNITION ON or ACCES- SORY mode, the driver’s door was closed after the key was carried outside the vehicle, and the shift lever was not in “P”

Turn the “ENGINE START STOP” switch OFF and close the driver’s door

Shift the shift lever to “P” and turn the “ENGINE START STOP” switch OFF

Shift the shift lever to “P”, turn the “ENGINE START STOP” switch OFF and close the driver’s door again

42

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Alarm

Situation

Interior alarm pings once*1

Interior alarm pings once and exterior alarm sounds 3 times*1

The electronic key has a low battery An attempt was made to start the engine without the electronic key being present, or the electronic key was not functioning normally The driver’s door was closed after the key was carried outside the vehicle, and the “ENGINE START STOP” switch was not turned off An occupant carried the electronic key outside the vehicle and closed the door while the “ENGINE START STOP” switch was not off

Correction procedure Replace the electronic key battery

Start the engine with the electronic key present*2

Turn the “ENGINE START STOP” switch OFF and close the driver’s door again

Bring the electronic key back into the vehi- cle

*1: A message will be shown on the multi-information display in the instru-

ment cluster.

*2: If the engine does not start when the electronic key is inside the vehicle, the electronic key battery may be depleted or there may be difficulties receiving signal from the key. (→P. 693)

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.

43

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Switching the door unlock function

It is possible to set which doors the entry function unlocks using the wireless remote control. STEP 1

Turn the “ENGINE START STOP” switch off.

STEP 2

When the indicator on the key surface is not on, press and hold (if

(if equipped) or equipped) for about 5 seconds while pressing and holding

(if equipped),

The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat

STEP 2

.)

Multi-information

display

Unlocking function

Beep

Holding the driver’s door handle unlocks only the driver’s door and driver side power sliding door. Holding the front passen- ger’s door handle or pull- ing either power sliding door handle unlocks all doors. Holding either front door handle or pulling either power sliding door handle unlocks all doors.

Exterior: Beeps three times Interior: Pings once

Exterior: Beeps twice Interior: Pings once

For vehicles equipped with an alarm, to prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (→P. 162)

44

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■Battery-saving function

In the following circumstances, the entry function is disabled in order to pre- vent the vehicle battery from discharging and the electronic key battery from discharging. ●When the entry function has not been used for 5 days or more ●When the electronic key has been left within approximately 6 ft. (2 m) of

the vehicle for 10 minutes or more

●If the entry function has not been used for 14 days or more, the vehicle cannot be unlocked by a door other than the driver’s door. To unlock the vehicle, grip the driver’s door handle or use the wireless remote control or the mechanical key.

The system will resume operation when... ●The vehicle is locked using the lock sensor when carrying the electronic

key on your person.

●The vehicle is locked/unlocked using the wireless remote control.

(→P. 53)

●The vehicle is locked/unlocked using the mechanical key. (→P. 767)

45

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Conditions affecting operation

The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system and wireless remote control from operating properly. (Way of coping →P. 767) ●When the electronic key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise

●When carrying a portable radio, cellular phone, cordless phone or other

wireless communication devices

●When the electronic key is in contact with, or is covered by the following

objects • Cards to which aluminum foil is attached • Cigarette boxes that have aluminum foil inside • Metallic wallets or bags • Coins • Hand warmers made of metal • Media such as CDs and DVDs

●When multiple electronic keys are in the vicinity ●When another wireless key (that emits radio waves) is being used nearby ●When carrying or using the electronic key together with the following

devices that emit radio waves • Another vehicle’s electronic key • A wireless key that emits radio waves • Personal computers or personal digital assistants (PDAs) • Digital audio players • Portable game systems

46

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

●If window tint with a metallic content or metallic objects are attached to

the rear window

●Vehicles with AUTO ACCESS SEAT: If the wireless remote control of the AUTO ACCESS SEAT is operated simultaneously, the AUTO ACCESS SEAT may not operate properly. For details, refer to “AUTO ACCESS SEAT OWNER’S MANUAL”.

■Notes for the entry function

●Even when the electronic key is within the effective range (detection

areas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.

• The electronic key is on the instrument panel, floor or in the glove box when the engine is started or “ENGINE START STOP” switch modes are changed.

●Do not leave the electronic key on top of the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave reception conditions, it may be detected by the antenna outside the cabin and the door will become lockable from the outside, possibly trapping the electronic key inside the vehicle.

●As long as the electronic key is within the effective range, the doors may be locked or unlocked by anyone. However, only the doors detecting the electronic key can be used to unlock the vehicle.

●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car wash when the electronic key is within the effective range. (The doors will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)

●If the wireless remote control is used to lock the doors when the elec- tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the smart key system. (Use the wireless remote control to unlock the doors.)

●If power slide door is unable to operate due to prohibition by the power sliding door main switch, the door unlock and open operation will not be performed. (→P. 70)

47

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Note for locking the doors

●Touching the door lock sensor while wearing gloves may delay or prevent

lock operation. Remove the gloves and touch the lock sensor again.

●When the lock operation is performed using the lock sensor, recognition signals will be shown up to two consecutive times. After this, no recogni- tion signals will be given.

●If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. Place the key in a position 6 ft. (2 m) or more separate from the vehicle while the vehi- cle is being washed. (Take care to ensure that the key is not stolen.)

●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on the multi-information display and a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.

●The lock sensor may not work properly if it comes into contact with ice, snow, mud, etc. Clean the lock sensor and attempt to operate it again, or use the lock sensor on the lower part of the door handle.

●Fingernails may scrape against the door during operation of the door handle. Be careful not to injure fingernails or damage the surface of the door.

48

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■Notes for the unlocking function

●Gripping the front door handle when wearing a glove may not unlock or

lock the door.

●A sudden approach to the effective range or door handle operation may prevent the doors from being unlocked. In this case, return the door han- dle to the original position and check that the doors have unlocked before pulling the door handle.

●If there is another electronic key in the detection area, it may take slightly longer to unlock the doors after one of the front door handles is gripped or one of sliding door handles is pulled.

■When the vehicle is not driven for extended periods

●To prevent theft of the vehicle, do not leave the electronic key within 6 ft.

(2 m) of the vehicle.

●The smart key system can be deactivated in advance. (→P. 815)

■To operate the system properly

Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention may not operate.)

■If the smart key system does not operate properly

●Locking and unlocking the doors: Use the mechanical key. (→P. 767) ●Starting the engine (→P. 768)

49

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Electronic key battery depletion

●The standard battery life is 1 to 2 years. ●If the battery becomes low, an alarm will sound in the cabin when the

engine stops. (→P. 41)

●As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (→P. 693) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller. • The LED indicator on the key surface does not turn on.

●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field. • TVs • Personal computers • Recharging cellular phones or cordless phones • Cellular phones, cordless phones and battery chargers • Glass top ranges • Table lamps

■When the electronic key battery is fully depleted

→P. 693

■Customization that can be configured at Toyota dealer

Settings (e.g. smart key system) can be changed. (Customizable features →P. 815)

50

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■Certification for the smart key system

FCC ID: HYQ14AEH FCC ID: HYQ13CZN

U.S.A. FCC ID: HYQ14ADR FCC ID: HYQ13CZM FCC ID: NI4TMLF8-20
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

51

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

CAUTION

■Caution regarding interference with electronic devices

●People with implanted pacemakers or cardiac defibrillators should keep

away from the smart key system antennas. (→P. 40) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.

●Users of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

Ask your Toyota dealer for details for disabling the entry function.

52

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors Wireless remote control

The wireless remote control can be used to lock and unlock the vehi- cle. Vehicles without a smart key system (type A)

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s side doors. Press- ing the button again within 3 seconds unlocks the other doors. Sounds the alarm (press and hold)* *: If equipped

53

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Vehicles without a smart key system (type B)

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s side doors. Press- ing the button again within 3 seconds unlocks the other doors. Opens and closes the left side power sliding door (press and hold) Opens and closes the right side power sliding door (press and hold) Opens and closes the power back door (press and hold)* Sounds alarm (press and hold)*

*: If equipped

54

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Vehicles with a smart key system

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s side doors. Press- ing the button again within 3 seconds unlocks the other doors. Opens and closes the left side power sliding door (press and hold) Opens and closes the right side power sliding door (press and hold) Opens and closes the power back door (press and hold) Sounds alarm (press and hold)

55

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Operation signals

Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

Back door: A buzzer sounds and the emergency flashers flash twice to

indicate that the back door has been opened/closed.

■Door lock buzzer

If an attempt to lock the doors (except for power sliding doors or power back door) is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.

■Panic mode

Vehicles without a smart key system

When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.

Vehicles with a smart key system

When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the electronic key.

56

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again. ■Power sliding door operation (vehicles with power sliding door)

Even if the door is locked, pressing and holding the sliding door buttons will unlock all doors and start open operation.

■Alarm (if equipped)

Using the wireless remote control to lock the doors will set the alarm system. (→P. 162)

■Reversing the operation of the power sliding door and power back

door (if equipped) Pressing the wireless remote control switch again while the door is operating will cause the operation to reverse. However, the reverse operation cannot be performed for the first second after automatic operation starts, even if the wireless remote control switch is pressed again.

57

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Conditions affecting operation

Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: ●Near a TV tower, radio station, electric power plant, airport or other facil-

ity that generates strong radio waves

●When carrying a portable radio, cellular phone or other wireless commu-

nication devices

●When multiple wireless keys are in the vicinity ●When the wireless key is in contact with, or is covered by, a metallic

object

●When a wireless key (that emits radio waves) is being used nearby ●When the wireless key has been left near an electrical appliance such as

a personal computer

●If window tint with a metallic content or metallic objects is attached to the

rear window

●Vehicles with AUTO ACCESS SEAT: If the wireless remote control of the AUTO ACCESS SEAT is operated simultaneously, the AUTO ACCESS SEAT may not operate properly. For details, refer to “AUTO ACCESS SEAT OWNER’S MANUAL”.

Vehicles with a smart key system →P. 46

■If the wireless remote control does not operate properly (vehicles with

a smart key system) Locking and unlocking the doors: Use the mechanical key. (→P. 767)

■Key battery depletion

Vehicles without a smart key system If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (→P. 693) Vehicles with a smart key system →P. 50

58

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

■When the electronic key battery is fully depleted

→P. 693

■Customization that can be configured at Toyota dealer

Settings (e.g. operation signal) can be changed. (Customizable features →P. 815)

■Certification for wireless remote control (vehicles without a smart key

system) This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

■Certification for wireless remote control (vehicles with a smart key sys-

FCC ID: HYQ14AEH FCC ID: HYQ13CZN

tem) U.S.A. FCC ID: HYQ14ADR FCC ID: HYQ13CZM FCC ID: NI4TMLF8-20
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

59

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors Front doors

The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (if equipped)

→P. 37

■ Wireless remote control

→P. 53

■ Key

Turning the key operates the doors as follows: Vehicles without a smart key system

Locks all the doors Unlocks all the doors Turning the key unlocks the driver’s side doors. Turning the key again within 3 seconds unlocks the other doors.

Vehicles with a smart key system The doors can also be locked and unlocked with the mechanical key. (→P. 767)

60

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Locks all the doors Unlocks all the doors

■ Door lock switch

■ Inside lock button

Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.

61

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Locking the front doors from the outside without a key

STEP 1

STEP 2

Move the inside lock button to the lock position. Close the door.

Vehicles without a smart key system The doors cannot be locked if either of the front doors is open and the key is in the engine switch. Vehicles with a smart key system The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle.

The key may not be detected correctly and the door may be locked.

62

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Automatic door locking and unlocking systems

The following functions can be set or cancelled:

Function

Shift position linked door locking function Shift position linked door unlocking function

Speed linked door lock- ing function

Driver’s door linked door unlocking function (vehicles without a smart key system) Driver’s door linked door unlocking function (vehicles with a smart key system)

Operation

Shifting the shift lever out of P locks all the doors. Shifting the shift lever to P unlocks all the doors. All the doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.

All the doors are unlocked when the driver’s door is opened within 10 seconds after turn- ing the engine switch to “ACC” or “LOCK”.

All the doors are unlocked when the driver’s door is opened within 10 seconds after turn- ing the “ENGINE START STOP” switch off.

63

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■ Setting and canceling the functions

To switch between set and canceled, follow the procedure below:

STEP 1

Vehicles without a smart key system Close all the doors and turn the engine switch to the “ON” position. (Perform step 2 within 10 seconds.) Vehicles with a smart key system Close all the doors and turn the “ENGINE START STOP” switch to IGNITION ON mode. (Perform step 2 within 10 sec- onds.)

64

SIENNA_U (OM45477U)

1

STEP 2

1-2. Opening, closing and locking the doors

Shift the shift lever to P or N, and press and hold the door lock switch ( ) for approxi- mately 5 seconds and then release.

or

to

corresponding

The shift lever and switch posi- tions the desired function to be set are shown in the following table. Use the same procedure to can- cel the function.

Function

Shift lever position

Door lock switch

position

Shift position linked door lock- ing function Shift position linked door unlocking function Speed linked door locking func- tion Driver’s door linked door unlock- ing function When the setting or canceling operation is complete, all doors are locked and then unlocked.

65

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■When all the doors are locked with the wireless remote control or key

The doors cannot be unlocked with the door lock switch. The door lock switch can be reset by unlocking all the doors with the wire- less remote control or key.

■Using the mechanical key (vehicles with a smart key system)

The doors can also be locked and unlocked with the mechanical key. (→P. 767)

■Customization that can be configured at Toyota dealer

Settings (e.g. unlocking function using a key) can be changed. (Customizable features: →P. 815)

CAUTION

■To prevent an accident

Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.

The doors may be opened and the passengers could be thrown out of the vehicle which may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in the locked position.

66

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors Sliding doors

Vehicles without power sliding doors The sliding doors can be opened and closed using the sliding door handle. The sliding door can be locked and unlocked using the wire- less remote control, door lock switch or inside lock knob. Vehicles with power sliding doors The power sliding doors can be opened and closed using the sliding door handle, power sliding door switches or wireless remote control. The power sliding doors can be locked and unlocked using the wire- less remote control, door lock switch or inside lock knob. ■ Wireless remote control

→P. 53

■ Door lock switch

→P. 61

■ Sliding door handle

Open/close

Vehicles with power sliding doors: The sliding door will be automatically and completely opened and closed by the fol- lowing. • Pulling the outside handle. • Sliding the inside handle for- ward to close or backward to open.

67

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■ Inside lock knobs

Unlocks Locks

■ Power sliding door switches (vehicles with power sliding

doors)

From front seats

Press the switch to open and close the following door.

The right side sliding door The left side sliding door Pressing the switch again while the door is operating will cause the operation to reverse. However, the reverse opera- tion cannot be performed for the first second after automatic operation starts, even if the switch is pressed again.

68

SIENNA_U (OM45477U)

1

From second seats

1-2. Opening, closing and locking the doors

Press the switch to open and close each sliding door.

Pressing the switch again while the door is operating will cause the operation to reverse. However, the reverse opera- tion cannot be performed for the first second after automatic operation starts, even if the switch is pressed again.

69

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

Canceling the power sliding door system (vehicles with power sliding doors)

Turn the main switch off to dis- able the power sliding door sys- tem. Off The sliding doors can only be opened and closed manually. On* The power sliding door can be opened and closed with the power sliding door switches for the front occupants or wireless remote control even if the sliding door child-protectors are locked. the switch should be visible when the switch is on.

*: Orange mark on

Locking the sliding doors from the outside without the wireless remote control

STEP 1

STEP 2

Move the inside lock knob to the lock position. Close the sliding door.

70

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

Sliding door child-protector locks

The sliding door cannot be opened by the inside door han- dle and the second seat sliding door switch when the lock is set. These locks can be set to prevent children from opening the sliding doors. Push down on each sliding door switch to lock that sliding door.

■The power sliding door can be operated when (vehicles with power

sliding doors) ●Open operation: The shift lever is in P. Close operation: The vehicle is stopped.

●The power sliding door system main switch is on. ●The power sliding door is unlocked. (Except for the wireless remote con-

trol operation or smart key system operation.)

●The sliding door child-protector lock is not set. (However, the switch for the front occupants and the outside handle still operate the power sliding door.)

71

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■Power sliding doors

●If the power sliding door outside handle is pulled while the power sliding

door is opening or closing, the door will reverse the operation direction.

●During opening operation:

Stroking the power sliding door handle forward will reverse the direction and start closing. Stroking the handle backward will continue opening. During closing operation: Stroking the power sliding door handle backward will reverse the direc- tion and start opening. Stroking the handle forward will continue closing.

●The power sliding doors can be opened/closed manually when the power

sliding door function is canceled with the main switch.

●Vehicles without a smart key system: A buzzer sounds if you put the shift lever out of P with the engine switch in the “ON” position and the sliding door not completely closed. Vehicles with a smart key system: A buzzer sounds if you put the shift lever out of P with the “ENGINE START STOP” switch in IGNITION ON mode and the sliding door not completely closed.

●Vehicles with AUTO ACCESS SEAT: If the AUTO ACCESS SEAT has not been locked in place after being stowed, the right-hand sliding door will not close and a beep will sound twice. For details, refer to “AUTO ACCESS SEAT OWNER’S MANUAL”.

72

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■The situations in which the sliding door does not open completely

The left side sliding door does not open completely when the fuel filler door is opened.

■Jam protection function (vehicles with power sliding doors)

●If anything obstructs the power sliding door while it is closing or opening, the power sliding door will automatically operate in the opposite direction. ●If the jam protection function operates during two consecutive opening and closing operations, the power sliding door will be stopped at that position and the power sliding door system will be canceled.

■Power sliding door brake function (vehicles with power sliding doors) When the power sliding door detects an abnormality and stops operating, power sliding door brake function may be activated. When brake function is activated, door movement is restricted by the brake and motion may appear to be not smooth. This is not malfunction. Move the door to fully closed posi- tion to reset the system and normal power sliding door function will resume.

■Sliding door closer (vehicles with power sliding doors)

In the event that the sliding door is left slightly open, the sliding door closer will automatically close it to the fully closed position.

73

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

■If the power sliding door is inoperative (vehicles with power sliding

doors) When the power sliding door detects an abnormality and stops opening and can not be completely closed manually, cancel the function as follows and close the door manually. After that, have the vehicle inspected and repaired by your Toyota dealer.

STEP 1

STEP 2

Remove the plug from the rear edge of the sliding door.

Insert a key in the hole and push the mechanical cancel lever.

■When the battery is disconnected (vehicles with power sliding doors)

The power sliding door system must be initialized in order to ensure proper operation. To initialize it, close the sliding doors completely by hand.

■Customization that can be configured at Toyota dealer

Settings (e.g. opening and closing operation) can be changed. (Customizable features: →P. 815)

74

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

CAUTION

■While driving

Observe the following precautions while driving. Failure to do so may cause a door to open unexpectedly and an occupant to fall out of the vehicle, resulting in death or serious injury. ●Ensure that all doors are properly closed. ●Always lock the doors. ●Set the sliding door child-protector locks when children are seated in the

vehicle.

●Always use a seat belt. ●Do not operate the inside handle of the doors while driving.

■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not leave children alone in the vehicle.

If a child is accidentally locked in the vehicle, they could have heat exhaustion.

●Do not allow a child to open or close the sliding door.

Doing so may cause the sliding door to move unexpectedly, or cause the child’s hands, head, or neck to be caught by the moving sliding door.

75

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

CAUTION

■Operating the sliding doors

Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●When opening or closing a sliding door, thoroughly check to make sure the

surrounding area is safe.

●When opening or closing the sliding doors with windows open, keep all

body parts clear of the windows.

●If anyone is in the vicinity, make sure they are clear of the door path and let

them know that the sliding door is about to open or close.

●Do not leave the sliding door at half-opened position because the sliding door is not latched at this position. The sliding door may move unexpect- edly on an incline.

76

SIENNA_U (OM45477U)

1

CAUTION

1-2. Opening, closing and locking the doors

●When the vehicle is stopped on a slope, the door will slide faster when opening or closing, so be especially careful that the passengers do not get hit or pinched by the door.

●Open the sliding door fully while pas- sengers are getting on or off on a down- ward slope. Do not operate the outside handle or inside handle while the door is open as the door could suddenly close by itself causing injury.

●When closing the sliding door, take extra care to prevent your fingers etc. from being caught.

77

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

CAUTION

■Sliding door closer (if equipped)

It

●In the event that the sliding door is left slightly open, the sliding door closer will automatically close it to the fully closed position. takes several seconds before the sliding door closer begins to operate. Be careful not to catch fingers or anything else in the sliding door, as this may cause bone fractures or other serious injuries.

●Use caution when using the sliding door closer. The sliding door closer

operates even when the power sliding door system is canceled.

■Power sliding doors

Observe the following precautions when the power sliding door system is on. Failure to do so may cause death or serious injury. ●When using the door handle to open or close the power sliding door, remove your hand from the door handle immediately after starting power sliding door operation. If you leave your hand on the door handle during operation, your hand, fingers, wrist etc. may be subjected to an excessive amount of force.

●Check the safety of the surrounding area to make sure there are no obsta-

cles or anything that could cause any of your belongings to get caught.

●If anyone is in the vicinity, make sure they are clear of the door path and let

them know that the sliding door is about to open or close.

78

SIENNA_U (OM45477U)

1

1-2. Opening, closing and locking the doors

CAUTION

●If the power sliding door system is turned off with the main switch while the sliding door is operating automatically, the automatic operation is stopped. The sliding door then has to be operated manually. Take extra care when on an incline, as the sliding door may open or close unexpectedly.

●On an incline, a sliding door may close by itself after it opens automati-

cally. Make sure the sliding door is fully open and secure.

●If the operating conditions of the power sliding door are no longer met, a buzzer may sound and the sliding door may stop opening or closing. The sliding door then has to be operated manually. Take extra care when on an incline, as the sliding door may open or close abruptly.

●In the following situations, the power sliding door may detect an abnormal- ity and automatic operation may be stopped. In this case, the sliding door has to be operated manually. Take extra care when on an incline, as the sliding door may open or close abruptly. • When the sliding door contacts an obstacle • Vehicles without a smart key system:

When the battery voltage suddenly drops, such as when the engine switch is turned to the “ON” position or the engine is started during automatic operation Vehicles with a smart key system: When the battery voltage suddenly drops, such as when the “ENGINE START STOP” switch is turned to IGNITION ON mode or the engine is started during automatic operation

79

SIENNA_U (OM45477U)

1-2. Opening, closing and locking the doors

CAUTION

●Do not attach any accessories other than genuine Toyota parts to the power sliding door. The power sliding door may not operate, causing itself to malfunction, or the power sliding door may close again after it is opened.

●When the child-protector locks are set, make sure to turn off the power sliding door system with the main switch in order to totally disable the sys- tem.

■Jam protection function (vehicles with power sliding doors)

Observe the following precautions. Failure to do so may cause death or serious injury. ●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just before the power sliding door fully closes. Be careful not to catch fingers or anything else.

●The jam protection function may not work depending on the shape of the

object that is caught. Be careful not to catch fingers or anything else.

80

SIENNA_U (OM45477U)

NOTICE

■Sliding door

1-2. Opening, closing and locking the doors

Make sure magazines are not bent or protruding from the sliding door pockets. Do not insert anything too big so that the shape of the sliding door pockets is dis- torted. Such objects may obstruct the opening/closing of the sliding doors, dam- age the sliding door pockets or the vehi- cle body, and may result in a malfunction.

■To prevent damage to your vehicle

●Vehicles with the power sliding door:

• Do not apply excessive force when the sliding door is operating. • Do not place your hand or foot near door hinges or rollers when the

sliding door is operating.

• Avoid forcibly opening the left side sliding door fully when the fuel filler

door is opened. Otherwise, the fuel filler door may be damaged.

• Take care not to damage the sensors (installed on the front edge of the

power sliding door) with a knife or other sharp object.

●Make sure there is nothing in the doorway before closing. ●Do not close the sliding door by applying the brakes. Doing so could cause

the sliding door to be damaged.

81

SIENNA_U (OM45477U)