2005 Toyota Sienna Owners Manual

If fuel consumption is poor, the driving range will be shorter.

indicates

the vehicle

is heading.

the direction The compass that the above case, it shows that the vehicle is heading south. The direction display is updated every 2
seconds.

In

Displays

NE SE SW NW

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct direction in the following conditions: D The vehicle is stopped immediately af-

ter turning. The compass does not adjust while the vehicle is stopped.

D The ignition switch is turned off imme-

diately after turning.

D The vehicle is on an inclined surface. D The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

D The vehicle is magnetized. (There is a magnet or a metal object on or near the roof.)

D The battery has been disconnected. The compass works to calibrate the direc- tion automatically while the vehicle is in motion, if deviation is small. For additional precision or see calibrating, COMPASS” below.

for complete THE

“CALIBRATING

333

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

the direction

If the system does not operate properly, contact your Toyota dealer.

indicated or

is not

The compass sensor is on the roof of the vehicle.

NOTICE

Do not put magnets or a metal object on or near the roof of the vehicle. Doing this may cause malfunction of the compass sensor.

the

from

CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on deviates true direction deter- mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust for this deviation; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature and cruise in- formation display” on page 331.)

2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 5 sec- onds until the “VAR” indication appears on the compass display.

3. Push

the “E/M” button several

times until the desired zone number appears on the compass display.

If the button is not pushed for 10 sec- onds, the display returns to the compass/ outside temperature mode and the number that is last set is memorized. To select the zone where the vehicle is currently following map.

located, refer

the

to

334

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Samoa: Guam: Saipan:

After calibration, leaving the system for several seconds returns to the compass mode.

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Zone number

335

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 10
seconds until the “CAL” indication ap- pears on the compass display. (At this time, the compass display is locked in “N”.)

3. Drive the vehicle in a circle at 8 km/h (5 mph) or less. If there is not enough space to drive in a circle, drive around the block.

When the “CAL” indication goes off and the compass returns to the normal mode, calibration is complete. If you want to restart the calibration be- fore the “MODE” and “E/M” buttons simultaneously for 10 seconds again.

is complete, push both of

it

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

the direction display on

CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. In this case, the compass needs to be cali- brated. To calibrate the compass manually, do the following; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature and cruise in- formation display” on page 331.)

336

05 SIENNA_U (L/O 0409)

Clock

Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. D Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

in a place where

D During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.

CAUTION

D When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

D Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

With manual air conditioning system

With automatic air conditioning system

337

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The key must be in the “ACC” or “ON” position. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00. When lights are turned on, the brightness of the time in- dication will be reduced.

instrument panel

the

05 SIENNA_U (L/O 0409)

Conversation mirror The conversation mirror is designed for the driver and front passenger to be able to look at the rear passengers without turning around.

CAUTION

Do not adjust the mirror while the vehicle is moving. Be sure to adjust the mirror only when the vehicle is stopped.

To use the mirror, push it down.

338

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

The mirror angle can be adjusted by push- ing its edge.

05 SIENNA_U (L/O 0409)

Toyota park assist system (type A)

The Toyota park assist system is de- signed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer while driving at approximate 10 km/h (6
mph) or less when parking the vehicle. This system uses sensors to detect ob- structions. This system works when the ignition key is at the “ON” position and the transmis- sion is not in the “P” position. D Rear and

rear corner sensors work only when the transmission is in the “R” position.

D When

the vehicle

is

forwarding,

the

front corner sensors work.

1: Rear sensors 2: Rear corner sensors 3: Front corner sensors

339

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

If the indicator is continuously on, have your Toyota dealer check the system. If the you do not hear clean the sensors with soft cloth.

indicator remains blinking but the buzzer sound,

Rear sensors

Rear corner sensors

Front corner sensors

To turn on: Push the switch. The indicator comes on and the buzzer will sound. To turn off: Push the switch again. In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. D When the temperature is extremely low. D When any of the sensors are malfunc-

tion.

340

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Front corner sensors

Distance shown as C in mm (in.)

Indicator and

buzzer

Approximately 600—400 (23.6—15.7)

Approximately 400—250 (15.7—9.8)

Approximately 250 (9.8) or less

Intermittent

Fast intermittent

Continuous

This system is designed to inform you of the approximate distance between your vehicle and an obstacle by indicator and buzzer. Rear sensors

Distance shown as A in mm (in.) Approximately 1800—900
(70.9—35.4) Approximately 900—550 (35.4—21.7) Approximately 550 (21.7) or less

Rear corner sensors

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

Distance shown as B in mm (in.)

Indicator and

buzzer

Approximately 850—520 (33.5—20.5)

Approximately 520—250 (20.5—9.8)

Approximately 250 (9.8) or less

Intermittent

Fast intermittent

Continuous

1: Front sensors 2: Rear corner sensors 3: Rear sensors

341

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

For vehicles sold in Canada

This ISM device compiles with Cana- dian ICES−001.

Perceptible area 1800 mm (70.9 in.) A: Approximately 850 mm (33.5 in.) B: Approximately C: Approximately 600 mm (23.6 in.) Perceptible area is limited as shown in the previous illustration. Check the area around the vehicle before driving and start driving slowly.

CAUTION

D The Toyota park assist system

is intended as an aid to assist you to park and is not a substitute for your personal judgment. Make your driving decisions based on your ob- servations.

D Do not attach accessories or other objects to the vehicle within the sensor perceptible area. Doing so may cause the system to malfunc- tion, which might result in an acci- dent.

D In certain situations,

the system will not function properly and when the vehicle approaches certain ob- jects, the system will not detect those objects. Therefore, always ob- serve the area around the vehicle and do not rely solely on the sys- tem.

342

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Toyota park assist system (type B)

In the following cases, the system may not work properly. D When ice, snow, mud or other objects

build up on the sensor.

D When the vehicle is parked in extreme- ly high or extremely low temperature for a long period.

The system may not detect the follow- ing. D Thin objects such as a wire or rope D Objects with a surface area too small reflect ultrasonic waves such as

to wire gauze

D Sound wave absorbing objects or mate-

D When driving on bumpy or graveled

rial such as cotton or snow

roads or on grass

D When a device such as a horn from another vehicle, motorcycle engine, or an air brake sound from a heavy−duty vehicle, issues ultrasonic waves, near your vehicle

D When attaching a two−way radio anten-

na

D When rain or water splashes on the

sensor.

D When operating the vehicle on an in-

clined surface

D When a radio antenna or fender pole

is mounted on your vehicle.

D When a

towing hitch is mounted on

your vehicle.

D A person near the vehicle (depending

on the type of clothes worn)

D Objects with a sharp edge D Small or short objects D Tall objects with an upper part project-

ing toward the vehicle

the

D Objects just under the bumper D Objects very close to your vehicle In Toyota dealer check the system. D When the bumper is damaged. D When the indicator is continuously on.

following cases, have your

1: Rear sensors 2: Rear corner sensors

The Toyota park assist system is de- signed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer while driving at approximate 10 km/h (6
mph) or less when parking the vehicle. This system uses sensors to detect ob- structions. This system works when the ignition key is at the “ON” position and the transmis- sion is in the “R” position. The sensors work only when the transmis- sion is in the “R” position.

343

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

If the indicator is continuously on, have your Toyota dealer check the system. If the you do not hear clean the sensors with soft cloth.

indicator remains blinking but the buzzer sound,

Rear sensors

Rear corner sensors

To turn on: Push the switch. The indicator comes on and the buzzer will sound. To turn off: Push the switch again. In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. D When the temperature is extremely low. D When any of the sensors are malfunc-

tion.

344

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

This system is designed to inform you of the approximate distance between your vehicle and an obstacle by indicator and buzzer. Rear sensors

Distance shown as A in mm (in.) Approximately 1800—900
(70.9—35.4) Approximately 900—550 (35.4—21.7) Approximately 550 (21.7) or less

Rear corner sensors

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

Distance shown as B in mm (in.)

Indicator and

buzzer

Approximately 850—520 (33.5—20.5)

Approximately 520—250 (20.5—9.8)

Approximately 250 (9.8) or less

Intermittent

Fast intermittent

Continuous

05 SIENNA_U (L/O 0409)

Perceptible area 1800 mm (70.9 in.) A: Approximately 850 mm (33.5 in.) B: Approximately Perceptible area is limited as shown in the previous illustration. Check the area around the vehicle before driving and start driving slowly.

1: Rear corner sensors 2: Rear sensors

345

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

For vehicles sold in Canada

This ISM device compiles with Cana- dian ICES−001.

CAUTION

D The Toyota park assist system

is intended as an aid to assist you to park and is not a substitute for your personal judgment. Make your driving decisions based on your ob- servations.

D Do not attach accessories or other objects to the vehicle within the sensor perceptible area. Doing so may cause the system to malfunc- tion, which might result in an acci- dent.

D In certain situations,

the system will not function properly and when the vehicle approaches certain ob- jects, the system will not detect those objects. Therefore, always ob- serve the area around the vehicle and do not rely solely on the sys- tem.

346

In the following cases, the system may not work properly. D When ice, snow, mud or other objects

build up on the sensor.

D When the vehicle is parked in extreme- ly high or extremely low temperature for a long period.

D When driving on bumpy or graveled

roads or on grass

D When a device such as a horn from another vehicle, motorcycle engine, or an air brake sound from a heavy−duty vehicle, issues ultrasonic waves, near your vehicle

D When attaching a two−way radio anten-

na

D When rain or water splashes on the

sensor.

D When operating the vehicle on an in-

clined surface

D When a radio antenna or fender pole

is mounted on your vehicle.

D When a

towing hitch is mounted on

your vehicle.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

The system may not detect the follow- ing. D Thin objects such as a wire or rope D Objects with a surface area too small reflect ultrasonic waves such as

to wire gauze

D Sound wave absorbing objects or mate-

rial such as cotton or snow

D A person near the vehicle (depending

on the type of clothes worn)

D Objects with a sharp edge D Small or short objects D Tall objects with an upper part project-

ing toward the vehicle

the

D Objects just under the bumper D Objects very close to your vehicle In Toyota dealer check the system. D When the bumper is damaged. D When the indicator is continuously on.

following cases, have your

Rear view monitor system The rear view monitor system assists the driver by displaying an image of the rear of the vehicle while backing up. The displayed image on the screen is a horizontally reversed mirror image of the inside rear view mirror. To display the rear view image on the screen, place the selector lever in the “R” position when the ignition switch in the “ON” position. If you move the selector lever out of the “R” position, the previous screen. Operating another func- tion of the navigation system will display another screen. The rear view monitor system is a supple- ment device intended to assist back up. When backing up, be sure to check be- hind and all around the vehicle visually.

the screen returns

to

CAUTION

the

D Never depend on

rear view monitor system entirely when back- ing up. Always make sure your in- tended oath is clear. Use caution just as you would when backing up any vehicle.

image on

D Never back up while looking only at the screen. The the screen is different from actual con- ditions. Depicted distances between objects and flat surfaces will differ from actual distances. If you back up while looking only at the screen, you may hit a vehicle, a person or an object. When backing up, be sure to check behind and all around the vehicle visually and with mir- rors before proceeding.

D Do not use the system when the back door is not completely closed.

347

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

D If the back of the vehicle is hit, the position and mounting angle of the camera may change. Be sure to have the camera’s position and mounting angle checked at your To- yota dealer.

D If the temperature changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally.

D If the camera lens becomes dirty, it If cannot transmit a clear water droplets, snow, or mud ad- here to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse.

image.

D The displayed image may become darker and moving images may be slightly distorted when the system is cold. When backing up, be sure to check behind and all around the vehicle visually and with mirror be- fore proceeding.

348

05 SIENNA_U (L/O 0409)

AREA DISPLAYED ON SCREEN Image is displayed approximately level on screen.

On screen

Corners of bumper

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

D The area detected by the camera is limited. The camera does not detect objects which are close to either corner of the bumper or under the bumper.

D The area displayed on the screen may vary according to vehicle orien- tation or road conditions.

05 SIENNA_U (L/O 0409)

D When water droplets are adhering to the camera, or when humidity is high (for example, when it rains)

D When

foreign matter

(for example, snow or mud) is adhering to the cam- era

D When the sun or the beam of head- lights is shining directly into the cam- era lens

THE REAR VIEW MONITOR SYSTEM CAMERA The rear view monitor system camera is located on the back door as shown in the illustration. The camera uses a special lens. The distance of the image that ap- pears on the screen differs from the actu- al distance. In it may become difficult to see the images on the screen, even when the system is functioning. D In the dark (for example, at night) D When the temperature near the lens is

following cases,

the

high or low

349

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Power outlets (12 VDC)

The power outlets (12 VDC) are de- signed for power supply for car acces- sories. The key must be in the “ACC” or “ON” position for the power outlets to be used.

NOTICE

the

z To prevent

fuse

from being blown, do not use the electricity over the total vehicle capacity of 12
VDC/120W (front and rear outlets together).

If a bright light (for example, sunlight re- flected off the vehicle body) is picked up by the camera, the smear effect∗ peculiar to the camera may occur. ∗: Smear effect—A phenomenon that oc- curs when a bright light (for example, sun- light reflected off is picked up by trans- mitted by light source appears to have a vertical streak above and below it.

the camera; when

the vehicle body)

the camera,

the

350

Front

Rear

z To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.

z Close the power outlet

lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

Power outlets (115 VAC)

Beside second seat

Beside third seat

05 SIENNA_U (L/O 0409)

The power outlets (115 VAC) are de- signed for use as a power supply for electric appliances in the vehicle. The key must be in the “ON” position for the power outlet to be used. The maximum capacity for this power out- let is 115 VAC/100W. If you attempt to use an appliance that requires more than 115 VAC or 100W, the protection circuit will activate and cut the power supply. The power supply will restart automatically when you use an appliance that operates within the 115 VAC/100W limits.

To use the power outlet, push the main switch on the instrument panel. An indicator light will illuminate to indicate that the power outlet is ready for use. Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off.

351

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

NOTICE

Certain electrical appliances may cause radio noise.

Glove box

z To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.

z Close the power outlet

lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

The power outlet is not designed for the following electric appliances even though their power consumption is un- der 115 VAC/100W. These appliances may not operate properly. D Appliances with high initial peak watt- age: cathode−ray tube type televisions, compressor−driven refrigerators, electric pumps, electric tools, etc.

D Measuring devices which process pre- cise data: medical equipment, measur- ing instruments, etc.

D Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc.

352

To use the glove box, do this. To open: Pull the lever. To lock: Insert the master key and turn it clockwise.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Garage door opener box

The box is designed to store a garage door opener transmitter. Open the cover and remove the Velcro loop.

Remove the paper strip covering the adhe- sive on back side of loop and adhere loop to back side of the transmitter near cen- ter.

Please note if transmitter has wire clip for sun visor, this clip must be removed prior to adhesion of the Velcro.

353

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Remove spacers from the center panel. Place one spacer on the pin that would be below transmitter button when the cover is closed. Close the cover.

When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the center panel of the cover.

Place the transmitter with Velcro loop fac- ing inside of box into the box. Make sure the located above button pins.

transmitter button

is

354

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

CAUTION

D To reduce the chance of injury in case of an accident or a sudden stop, always keep the garage door opener box closed while driving.

D Keep the remaining spacers away

from children.

If the center panel does not contact your garage door opener transmitter: D Check to see if spacer is on the cor-

rect pin.

D Attach another spacer

top of original spacer. Check operation. If re- quired, continue to add spacers until contact is achieved.

to the

If the transmitter is clattering during driv- ing, fill in a piece of felt or pad to prevent the transmitter from clattering.

Auxiliary boxes To use the auxiliary box, open the lid as shown in the following illustrations. Type C—The plate in the center of the auxiliary box can be adjusted or removed as shown in the illustration. Type I—For details, see “Front seat side table” on page 367 in this Section.

CAUTION

D To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

D Type A and L—As these holders are designed for holding a light object such as an eyeglass, do not place any heavy objects in them. Heavy objects may cause the holder to open and contents to fly out result- ing in injuries.

355

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

NOTICE

z Type A and L—During hot weather, the interior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.

z Type L—To prevent damage to the auxiliary box, do not place any ob- ject heavier than 250 g (0.55 lb.) in it.

Type A (driver’s side roof)

Position 1

Position 2

356

Type B (instrument panel)

Type C (instrument panel without seat heater switches)

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Type D (instrument panel with seat heater switches)

Type F (front door)

Type H (spare tire cover)

Type E (upper side of the glove box)

Type G (quarter trim)

Type I (front seat side table)

357

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Coin holder

Type J (rear side of console box)

Type L (center roof with rear seat audio system)

Type K (front passenger’s seat)

358

To use the coin holder, push the but- ton.

CAUTION

To reduce the chance of in case of an accident or a sudden stop while driving, keep the coin holder closed when it is not in use.

injury

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

Cup holders The cup holder is designed for holding cups or drink−cans. To use them, ob- serve the following illustrations. Type C and D—For details, see “Front seat side table” on page 367 in this Sec- tion. Type G—For details, see “Removable con- sole box” on page 362 in this Section.

CAUTION

D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

reduce

D Type A and F—To

the chance of injury in case of an acci- dent or a sudden stop while driv- ing, keep the cup holder closed when it is not in use.

05 SIENNA_U (L/O 0409)

Type A (instrument panel)

Type C (front side of the front seat side table)

Type B (quarter trim)

Type D (rear side of the front seat side table)

359

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Type E (front side of console box)

Type G (console box tray)

360

Type F (rear side of console box)

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Bottle holders

Storage box

Front door

Sliding door

The bottle holders are designed to hold bottles securely.

CAUTION

Do not attempt to use the holder for any other purpose for which it was intended. Inappropriately sized or shaped objects may be thrown about in the compartment and possibly in- jure people in the vehicle during a sudden braking or an accident.

NOTICE

Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes.

This box is designed to place things like bottles.

361

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Removable console box

UPPER TRAY To access the upper tray, raise the con- sole box lid.

CONSOLE BOX To access the console box, pull up the lock release lever and raise the console box lid.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

362

05 SIENNA_U (L/O 0409)

THE

INSTALLING

REMOVING AND CONSOLE BOX The console box can be removed and installed between the front seats and between the second seats as shown in the illustrations. When the console box is installed in the second seat position, the right side sec- ond seat must be in the outside position.

Between the front seats

Between the second seats

To remove the console box: Open the auxiliary box of the rear side and pull up the lock release lever to disengage the rear lock. Then lift the console box and release the front hook.

363

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

To install the console box between the front seats: 1. Install the front hook in the front striker of the console box under− tray.

2. Rotate down straight and push down

to engage the rear lock.

CAUTION

D Be careful not to get your hands or

feet pinched in the console box.

D Make sure the console box is se- curely locked by pushing forward, rearward, upward and sideways. Failure to do so may cause an un- expected accident or severe injury in the event of emergency braking or a collision.

364

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

To install the console box between the second seats: 1. Install the front hook

in the rear

striker of the double striker set.

The striker is used as both the console box lock striker and the right second seat lock striker when the right second seat is in the inside position. 2. Rotate down straight and push down

to engage the rear lock.

CAUTION

D Do not install the console box by any means other than the center striker between the second seats. Otherwise, the console box cannot be installed properly.

D Be careful not to get your hands or

feet pinched in the console box.

D Make sure the console box is se- curely locked by pushing forward and rearward. Failure to do so may cause an unexpected accident or severe injury in the event of emer- gency braking or a collision.

CONSOLE BOX TRAY When the console box is not installed between the front seats, the cup holder and small tray can be installed in the console box under−tray between the front seats. The cup holder and small tray are in the console box.

installing

Before the cup holder, push down the bottom of the cup and turn it counterclockwise to lock.

365

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Note pad holder

CAUTION

D Make sure the the cup holder and small tray are securely locked by pushing forward and rearward when they are installed. Failure to do so may cause an unexpected accident or severe in the event of emergency braking or a collision.

injury

D Do not place anything other than cups or drink cans in the cup hold- er, and do not place anything in the console box items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

tray, as such

D To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the cup holder and small tray stored when they are not in use.

the

front of

To install the cup holder and small tray: Cup holder—Hook the cup holder to the console box under−tray, then push down the back of the cup holder to secure it. Small tray—Hook the back of the small tray to the console box under−tray, then push down the front of the small tray to secure it. Make sure the cup holder and small tray are locked securely.

366

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Front seat side table

The note pad holder hold small paper such as note pads. To use the holder, raise the console box upper lid.

is designed to

CAUTION

D Do not write on the note pad holder

while the vehicle is moving.

D Do not place anything else on the note pad holder. Such items may be in the compartment thrown about and possibly cause injury during sudden braking or an accident.

D To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the console box upper lid closed when it is not in use.

The front seat side table can be used as a cup holder or auxiliary box. It can be also used as a temporary table only when the vehicle is stopped.

The auxiliary box of the table can also be used as a cup holder. To use as a cup holder, open the lid and pull down the tab as shown in the illustration.

367

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Coat hooks

CAUTION

D Do not put heavy things on the front seat side table. The table may fall down and cause personal injury. D To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

D Do not place anything else other than cups or drink−cans in the cup holder, as such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

D To reduce the chance of injury in case of an accident or a sudden stop while driving, make sure the table is folded down and locked se- curely when it is not in use.

To fold down the table, pull up the lock release lever and push against the driver’s seat side. Make sure the table is locked securely.

368

To use the coat hook, pull it down.

CAUTION

Vehicles with side airbags and curtain shield airbags—Do not hook a hanger, heavy or sharp pointed object on the coat hook. If the curtain shield airbag inflates, those items will be hurled away with great force or the curtain shield airbag may not activate cor- rectly. When you hang clothes, hang them on the coat hook directly.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Grocery bag hooks These hooks are designed things like grocery bags. Type A—To use the hook, pull it down. Type D—To use the hook, pull it up.

to hang

CAUTION

Type A and D—To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the hook stored when it is not in use.

NOTICE

Type A (instrument panel)

Type C (third seats)

z Type A, B, and C—To prevent dam- age to the hook, do not hang any object heavier than 4 kg (8.8 lb.) in it.

z Type D—To prevent damage to the hook, avoid hanging heavy loads on it.

Type B (front seats)

Type D (under the back door)

369

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

Cargo net hooks

Pattern 1

Pattern 3

Pattern 2

370

Pattern 4

05 SIENNA_U (L/O 0409)

These hooks are designed to be used for the cargo net. The cargo net can be used in a variety of ways as shown in the illustrations. The cargo net itself is not included as an original equipment.

NOTICE

To prevent damage avoid using them than the cargo net.

to

the hooks, things other

for

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Tie−down hooks

Roof luggage carrier

CAUTION

When you load cargo on the roof lug- gage carrier, observe the following: D Place the cargo so that its weight is distributed evenly between the front and rear axles.

To secure your luggage, use the tie− down hooks as shown above. See “—Stowage precautions” on page 399
in Section 2 for precautions when loading luggage.

CAUTION

To avoid personal injury, keep the tie− down hooks folded when not in use.

The roof luggage carrier consists of roof rails (1) attached to the roof and sliding cross rails (2). To adjust the positions of cross rails, do this. 1. Turn

the knobs counterclockwise

to

loosen the cross rails. the cross rails

2. Slide

position various sizes.

for

loading

to the

the desired luggages of

3. After adjusting, be sure to tighten the cross rails by turning knobs clockwise. Follow the manufacturer’s instructions and precautions when the attach- ments or their equivalent.

installing

D If loading long or wide cargo, never exceed the vehicle overall length or width. and weights” on page 496 in Section 8
for information on your vehicle overall length and width.)

“Dimensions

(See

D Before driving, make sure the cargo the roof

fastened on

is securely luggage carrier.

D Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu- vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor- rectly.

371

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Sun shade

Rear window

To use the sun shade, pull the tab of the shade and hook it on the anchors. To store the shade, pull the tab slightly to unhook the shade, and lower it slow- ly.

NOTICE

z Do not place anything where

it might hinder the opening/closing of the shade.

z Do not place anything on

the

shade.

D If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place.

D Do not exceed 68 kg (150 lb.) cargo weight on the roof luggage carrier.

NOTICE

When loading the luggages, be careful not the moon roof.

the surface of

to scratch

372

Quarter window

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Floor mat

Use a floor mat of the correct size. If the floor carpet and floor mat have two holes, then it is designed for use with two locking clips. Fix the floor mat with lock- ing clips into the holes in the floor carpet.

CAUTION

Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.

interferes with

373

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

374

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

SECTION 2

INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Break−in period Fuel Fuel pump shut off system Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Brake pad wear limit indicators Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

376
376
378
378
379
380
380
381
382
386
386
387
387
388
398
399
402

375

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: D Avoid full

throttle acceleration when

starting and driving.

D Avoid racing the engine. D Try to avoid hard stops during the first

300 km (200 miles).

D Do not drive for a long time at any

single speed, either fast or slow.

D Do not tow a trailer during the first 800

km (500 miles).

Fuel FUEL TYPE Your new vehicle must use only un- leaded gasoline. To help prevent gas station mix−ups, your Toyota has a smaller fuel tank opening. The special nozzle on pumps with un- leaded fuel will fit it, but the larger stan- dard nozzle on pumps with leaded gas will not. At a minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.

NOTICE

Do not use leaded gasoline. Use of leaded gasoline will cause the three− way catalytic converter to lose its ef- fectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

OCTANE RATING Select Octane Rating 87 (Research Octane Number 91) or higher. For improved vehicle performance, the use of premium unleaded gasoline with an Octane Rating of 91 (Research Octane Number 96) or higher is recommended. Use of unleaded gasoline with an octane rating or research octane number lower than stated above will cause persistent heavy knocking. If it is severe, this will lead to engine damage. If your engine knocks... If you detect heavy knocking even when using if you hear steady knocking while holding a steady speed on level roads, consult your Toyota dealer. However, occasionally, you may notice light knocking for a short time while accel- erating or driving up hills. This is normal and there is no need for concern.

the recommended

fuel, or

376

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

in

GASOLINE CONTAINING DETERGENT ADDITIVES Toyota recommends the use of gasoline that contains detergent additives to avoid build−up of engine deposits. However, all gasoline sold the U.S. contains detergent additives to keep clean and/or clean intake systems. QUALITY GASOLINE Automotive manufacturers in the U.S., Europe and Japan have developed a specification fuel named World−Wide Fuel Charter (WWFC) that is expected to be applied world wide. The WWFC consists of four categories that depend on required emission lev- els. In the U.S., category 4 has been adopted. The WWFC improves air quali- ty by providing for better emissions in vehicle fleets, and customer satisfaction through better vehicle performance.

for quality

05 SIENNA_U (L/O 0409)

GASOLINE CONTAINING MMT Some gasoline contain an octane en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel con- taining MMT is used, your emission con- trol system may be adversely affected. The Malfunction Indicator Lamp on the in- strument cluster may come on. If this hap- pens, contact your Toyota dealer for ser- vice.

CLEANER BURNING GASOLINE Cleaner burning gasoline, including re- formulated gasoline that contains oxy- genates such as ethanol or MTBE is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gas- oline provide excellent vehicle perfor- mance, reduce vehicle emissions, and im- prove air quality. OXYGENATES IN GASOLINE Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.

If you use gasohol

377

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

GASOLINE QUALITY In a very few cases, you may experience driveability problems caused by the partic- ular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer.

Fuel pump shut off system The fuel pump shut off system stops sup- plying fuel to the engine to minimize the risk of fuel leakage when the engine stalls or an airbag inflates upon collision. To restart the engine after the fuel pump shut off system activates, ignition switch to “ACC” or “LOCK” once and start it.

turn

the

NOTICE

CAUTION

Inspect the ground under the vehicle before restarting the engine. If you find that liquid has leaked onto the ground, fuel system has been damaged and it is in need of repair. In this case, do not restart the engine.

the

is

it

z Do not use gasohol other

than stated above. It will cause fuel sys- tem damage or vehicle performance problems.

z If driveability problems occur (poor engine

hot knock, etc.), discontinue the use.

vaporizing,

starting,

z Take care not to spill gasohol dur- ing refueling. Gasohol may cause paint damage.

FUEL TANK CAPACITY

79 L (21 gal., 17.5 Imp. gal.)

378

Operation in foreign countries If you plan to drive your Toyota another country... First, comply with the vehicle registration laws. Second, confirm the availability of the cor- rect fuel (unleaded and minimum octane number).

in

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Three−way catalytic converters

The three−way catalytic converter is an emission control device installed in the exhaust system. The purpose is to reduce pollutants in the exhaust gas.

CAUTION

D Keep people and combustible mate- rials away from the exhaust pipe while the engine is running. The exhaust gas is very hot.

D Do not drive, idle or park your ve- hicle over anything that might burn easily such as grass, leaves, paper or rags.

NOTICE

large amount of unburned gases into the three−way catalytic flowing converter may cause it to overheat and create a fire hazard. To prevent this and other damage, observe the following precautions: z Use only unleaded gasoline. z Do not drive with an extremely low fuel level; running out of fuel could cause the engine to misfire, creat- ing an excessive load on the three− way catalytic converter.

z Do not allow the engine to run at idle speed for more than 20 min- utes.

z Avoid racing the engine. z Do not push−start or pull−start your

vehicle.

z Do not turn off the ignition while

the vehicle is moving.

in

z Keep your engine in good running order. Malfunctions the engine electrical system, electronic ignition system/distributor ignition system or fuel system could cause an ex- tremely high three−way catalytic converter temperature.

z If the engine becomes difficult to start or stalls frequently, take your vehicle in for a check−up as soon as possible. Remember, your Toyota dealer knows your vehicle and its three−way catalytic converter sys- tem best.

z To ensure that the three−way cata- lytic converter and the entire emis- sion control system operate proper- ly, your vehicle must receive the periodic inspections required by the Toyota Maintenance Schedule. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.

379

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

D Keep

the back door and quarter windows closed while driving. An open or unsealed back door and quarter windows may cause exhaust gases to be drawn into the vehicle. D To allow proper operation of your vehicle’s ventilation system, keep the inlet grilles in front of the wind- shield clear of snow, leaves, or oth- er obstructions.

D If you smell exhaust fumes in the the windows vehicle, drive with open and the back door and quarter windows closed. Have the cause im- mediately located and corrected.

Engine exhaust cautions

CAUTION

D Avoid inhaling the engine exhaust. It contains carbon monoxide, which is a colorless and odorless gas. It can cause unconsciousness or even death.

D Make sure the exhaust system has no holes or loose connections. The system should be checked from time to time. If you hit something, or notice a change in the sound of the the system exhaust, have checked immediately.

D Do not run the engine in a garage or enclosed area except the time needed to drive the vehicle in or out. The exhaust gases cannot escape, making this a particularly dangerous situation.