2005 Toyota Sienna Owners Manual

CANCELLING THE PRESET SPEED You can cancel the preset speed by doing any of the following: a. Pulling lever

“CANCEL”

the

the

in

SETTING THE DESIRED SPEED The transmission must be in “D” before you set the cruise control speed in the conventional cruise control mode. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed and the display shows the preset speed. You can now take your foot off the accelerator pedal. If you need to accelerate—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you release the accelerator pedal, the vehicle will return to the speed set prior to acceleration.

direction.

b. Depressing the brake pedal. c. Pressing the “ON−OFF” button. In the following cases, the preset speed automatically cancels out: a. The vehicle speed

falls below about

40km/h (25 mph).

b. If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the pre- set speed will also automatically be cancelled.

c. The slip indicator light blinks and an alarm sounds. (This occurs when the vehicle is about to skid.)

If cancelled by b., the preset speed data is cleared and you must set the speed from the beginning.

If the preset speed automatically cancels out for other than the above reasons, do not operate the cruise control. Although it is no problem to continue driving, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased 1.6 km/h (1 mph) each time by pushing the lever up in the “+ RES” direction quickly within 0.6 seconds. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction.

217

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

If this code appears, press the “ON−OFF” button to turn the system off and then push it again to turn it on. If the setting still cannot be made or the same code appears again, the system might have malfunctioned. Although there is no prob- lem to continue driving, please contact your Toyota dealer.

RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered 1.6 km/h (1 mph) each time by pushing the lever down in the “− SET” direction quickly within 0.6 seconds. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction. Even if you downshift from “D” to “4” in the conventional cruise control mode, en- gine braking will not be enabled because this mode is not cancelled. To decrease the vehicle’s speed, reset to a slower speed with the cruise control lever or de- press the brake pedal, cruise control is cancelled.

the brake pedal.

If you use

RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the lever, by depressing the brake pedal or by activating the vehicle stability con- trol system, pushing the lever up in the “+ RES” direction will restore the speed set prior to cancellation. If the preset speed is cancelled when ve- hicle speed falls below about 40 km/h (25
mph), the preset speed will be resumed when vehicle speed exceeds about 40
km/h (25 mph) again. CONVENTIONAL MODE FAILURE WARNING If the conventional cruise control mode, the “CRUISE” indica- tor light in the instrument cluster flashes, the master warning light comes on and the alarm sounds, the warning code “E3” will appear on the display. If a system malfunction is detected when the conventional cruise control mode is in the ready mode or operating, the master warning light comes on, an alarm sounds and the above code appears.

CONTROL

CRUISE

trouble

there

in

is

218

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference Using your audio system Audio remote controls Rear seat audio system Rear seat entertainment system Audio/video system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

220
221
238
240
249
300

For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”.

219

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Reference

Type 1−1: AM·FM radio/cassette player/ compact disc player (with compact disc changer controller)

Type 1−2: AM·FM radio/cassette player/ compact disc player (with compact disc changer controller)

Type 2: AM·FM radio/cassette player/com- pact disc player with changer

220

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

“FM”,

“AM”,

“TAPE”,

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “DISC” or “LOAD” to turn on that function without pushing “PWR·VOL”. To turn on the cas- sette or compact disc player, a cassette or compact disc must be loaded in the player. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the other function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “DISC” or “LOAD” if the system is already on but you want to switch from one function to another.

“TAPE”,

“AM”,

“FM”,

YOUR RADIO ANTENNA Your vehicle has the mast type antenna or on−glass antenna printed on the inside of the rear quarter window. Mast type antenna—To remove an anten- na, carefully turn it counterclockwise.

NOTICE

z Mast type antenna:

it

To prevent damage to the antenna, make sure is removed before driving your Toyota through an au- tomatic car wash. z On−glass antenna:

Attaching the film (especially con- ductive or metallic type) on the rear glass will noticeably the sensitivity of the radio.

reduce

221

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

YOUR COMPACT DISC PLAYER WITH CHANGER (type 2) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. This compact disc play- er can store up to six discs. The player will play from track 1 through to the end of the disc. Then it will play from track 1 of the next disc.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

(type

YOUR COMPACT DISC PLAYER 1−1 and 1−2) When you insert a disc, gently push it in with the label side up. The player will play from track 1 through to the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

222

NOTICE

z Do not stack up two discs for in- sertion, or it will cause damage to the compact disc changer. Insert only one compact disc into slot at a time.

z Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a com- pact disc into the slot.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Controls and features "Type 1−1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

223

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

"Type 1−2

224

05 SIENNA_U (L/O 0409)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK·TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To recall a preset station: Push the button for the station you want. The button num- ber and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc.

05 SIENNA_U (L/O 0409)

(Program)

Compact disc player

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast−forward button)

Cassette player

Push “ ” (preset button 6) to fast−for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast−forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast−forwards completely, the cassette will play the other side of the tape using the auto−reverse feature.

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. Type 1−1— BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7.

tone and balance,

time

turn

you

the

the

225

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. Type 1−2— BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. SURROUND: Turn on or off the surround function. “SUR- ROUND OFF” will appear on the display. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played.

“SURROUND ON” or

226

Vehicles with rear seat entertainment sys- tem— The “DISC” button may also be used to operate a DVD player when a disc is loaded in the DVD player. Pressing the “DISC” button changes between the CD player and DVD player. When the DVD player is in operation, “AUX” appears on the display. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid.

incorrectly

inserted

B NR∗

If the malfunction still exists, take your vehicle to your Toyota dealer. Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select the disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push “ ” will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.

” (preset button 3). “

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again.

in random order, or

random

feature, push

With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again. RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

the repeat

the

track

Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

227

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “Ɯ” or “Ɲ” side of the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5
seconds, and then move to the next pre- set station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. The radio will find the next station up or down the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. “SCAN” will appear on the display and the player will scan up or down all the tracks on the disc you are listening to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. The discs in the compact disc changer can be scanned up only. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push “Ɯ” side of the “SCAN” button until ·SCAN” will appear you hear a beep. “ on the display and the player will scan up the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scanning.

228

of

or

“Ɲ”

“Ɯ”

side

the seek mode,

the radio finds and the next station up or down the

SEEK·TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release the “SEEK·TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

to

to

title,

track

then back

TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

of

or

“Ɲ”

“Ɯ”

side

the current

the down side of

Compact disc player Use this button to skip up or down to a different track. Push the “SEEK·TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the beginning of track, quickly push the button one time. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK·TRACK” button. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

side of

“Ɯ” or

“Ɲ”

the

229

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

"Type 2

230

05 SIENNA_U (L/O 0409)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK·TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. RDS stations will be preset to the buttons when you turn on the RDS. (See “RDS” button.) To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM, two FM and RDS stations for each button. (The display will show “FM TYPE” when you push “AM” or “FM” but- ton.)

“FM2” or

“FM1”,

“AM”,

05 SIENNA_U (L/O 0409)

(Eject button)

(Program)

Cassette player This button is used to eject a cassette. Compact disc player This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast−forward button)

Cassette player

Push “ ” (preset button 6) to fast−for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast−forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast−forwards completely, the cassette will play the other side of the tape using the auto−reverse feature.

231

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

“SURROUND ON” or

BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. SURROUND: Turn on or off the surround function. “SUR- ROUND OFF” will appear on the display. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Vehicles with rear seat entertainment sys- tem— The “DISC” button may also be used to operate a DVD player when a disc is loaded in the DVD player. Pressing the “DISC” button changes between the CD player and DVD player. When the DVD player is in operation, “AUX” appears on the display.

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. Ɲ DISC Ɯ Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen to appears on the display.

Compact disc player

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7.

tone and balance,

time

turn

you

the

the

232

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

B NR∗

” (preset button 3). “

Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, ” will push “ appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM Push the “FM” button to turn on the radio and select the FM band. “FM1”, “FM2” or “FM TYPE” will appear on the display. This system allows you to set twelve FM and six RDS stations, three for each of the preset button. If the RDS is off or RDS stations are not preset to the preset buttons, “FM TYPE” will not appear on the display.

in

LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close. If no compact disc is inserted, the shutter will close after 15 seconds. To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on). When the indicators on both sides of the slot turn green, insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shut- ter will automatically open again and the indicators will turn green so the next disc can be inserted. The same process can be applied the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume.

the rest of

loading

for

in random order, or

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

233

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

the repeat

RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again.

track

the

RDS (Radio Data System) Your audio system is equipped with Radio Data System (RDS). RDS station providing good reception is automatically selected if current reception worsens. The “RDS” button turns the RDS on and off. This button is operational except in AM mode. To turn on the RDS, push and hold this button until you hear a beep and “RDS” will appear on the display. At this time, the radio starts to search the RDS sta- tions and “RDS SEARCH” will flash on the display. Quickly push and release this button when the RDS to “RDS the RDS stations and search SEARCH” will flash on the display. When found, stations are “FOUND” and the number of the RDS sta- tions will appear on the display, and you will hear two beeps. The stations will be preset to the preset buttons. If the RDS stations can not be found, “NO RDS ST” will appear on the display and you will hear a beep, and the display returns to the previous mode. To turn the RDS off, push the button until you hear a beep again.

the radio starts

the RDS

turns on,

234

Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “Ɯ” or “Ɲ” side of the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5
seconds, and then move to the next pre- set station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. The radio will find the next station up or down the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. “SCAN” will appear on the display and the player will scan up or down all the tracks on the disc you are listening to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. The discs in the compact disc changer of separate unit can be scanned up only. Scanning the first tracks of all the discs in the magazine: Push “Ɯ” or “Ɲ” side of the “SCAN” but- ·SCAN” will ton until you hear a beep. “ appear on the display and the player will scan up or down the first track of the next disc. To stop scanning, push this button again. the auto changer has scanned all the discs, it will stop scan- ning. The discs in the compact disc changer of separate unit can be scanned up only.

If

of

or

“Ɲ”

“Ɯ”

side

the seek mode,

the radio finds and the next station up or down the

SEEK·TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release the “SEEK·TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

of

or

“Ɲ”

“Ɯ”

side

the current

the down side of

Compact disc player Use this button to skip up or down to a different track. Push the “SEEK·TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the beginning of track, quickly push the button one time. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “SEEK·TRACK” button. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

side of

“Ɯ” or

“Ɲ”

the

235

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

in RDS

is operational only

TEXT Radio This button mode. When an RDS radio station transmits a text message, “TEXT” will be displayed. At this time, push the “TEXT” button to view the text message. The message display will be canceled if any button that affects the display is pushed. To view the mes- sage again, push this button again. After the entire message has been displayed, the message will disappear. The RDS audio system has memory to store three 64−character messages. To store a message in memory, push and hold the “TEXT” button until you hear a beep. If three messages are already stored in memory, the oldest message will be over- written by the new message. To recall a radio text message, push the “TEXT” button momentarily. This will dis- play the most recent message. Each push of the button will display messages in the order of most to least recent.

If no messages have been stored, or if there are no more messages to be re- called, “NO MESSAGE” will appear on the display, and the message display will be canceled. The message display will be canceled if you activate any function that affects the display. Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

to

the

“TRAF” button,

TRAF (Traffic) This button turns the traffic announcement (TA) feature on and off. This button is operational only in FM mode. By pushing “TRAF SEEK” will flash on the display and the radio will start seeking any traffic program station. When a traffic program station is found, “TRAF” will be displayed and you will hear a beep. After the traffic announcement program is over, the display returns to the previous mode. If no traffic program station is found, “NO TRAF INFO” appears on the display for a few seconds and the display returns to the previous mode. To cancel the traffic announcement, push this button again. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

236

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

TYPE (Program Types) When you push the “TYPE” button while receiving an RDS station, the current pro- gram type appears on the display. Each time you push this button, the pro- gram type changes as in the following: D ROCK D EASY LIS (Easy listening) D CLS/JAZZ (Classical music and Jazz) D R&B (Rhythm and Blues) D INFORM (Information) D RELIGION D MISC (Miscellaneous) D ALERT (Emergency message)

237

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

Audio remote controls (steering switches)

05 SIENNA_U (L/O 0409)

Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. 1. Volume control switch 2. “ƜƝ” switch 3. “MODE” switch

238

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

to

increase while

1. Volume control switch Push “+” to increase the volume. The vol- ume continues the switch is being pushed. Push “−” the volume. The to decrease volume continues to decrease while the switch is being pushed. 2. “ƜƝ” switch Radio This switch has the following features— To select a preset station: Quickly push and release the “Ɯ” or “Ɲ” side of the switch. Do this again to select the next preset station. To seek a station: Push and hold the “Ɯ” or “Ɲ” side of the switch until you hear a beep. Do this again to find the next station. If you push the switch on either side during the seek mode, seeking will be cancelled. To step up or down the frequency, push and hold the switch even after you hear a beep. When you the switch, the radio will begin seeking up or down for a station. Do this again to find the next station.

release

from

Cassette player This switch has the following features— To skip to a different track in either direc- tion: Quickly push and release the “Ɯ” or “Ɲ” side of the switch. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track switch until the track you want to listen to is set. If you push the switch ten times, the skip function will turn off. (You can skip up to nine tracks at a time.) When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two tracks before the song you are listening to, push the “Ɲ” side of the switch three times. If you push the track switch further than you wanted to, push the other side of the switch. The in- creased or reduced. The track number you select is not valid if the tracks remaining on the current side of the cassette.

track number will be

the number of

is higher

than

it

D When the tape reaches to the begin- ning, the player will automatically start playing that side.

D After the tape reaches to the end, the reverse and

player will automatically start playing the other side.

There must be at least 3 seconds of blank space between tracks for the track switch to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. To fast forward or reverse: Push and hold the “Ɯ” side of the switch to fast forward a cassette tape. “FF” will appear on the display. Push and hold the “Ɲ” side of the switch to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push the “Ɯ” side of the switch. To stop the tape while it is rewinding, push the “Ɲ” side of the switch. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature.

239

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

To turn the audio system off, push and hold the “MODE” switch until the system turns off.

Compact disc player Use this switch to skip up or down to a different track in either direction. Quickly push and release the “Ɯ” or “Ɲ” side of the switch until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “Ɲ” side of the switch once, quickly. Vehicles with rear seat entertainment sys- tem— While the DVD player is in operation, the chapter or track can be changed by push- ing the “Ɯ” or “Ɲ” side of the switch. With compact disc changer only— Push and hold the “Ɯ” or “Ɲ” side of the switch until the disc you want to listen to is set. 3. “MODE” switch Push the “MODE” switch to select an au- dio mode. Each push changes the mode sequentially if the desired mode is ready to use. The DVD player will be selectable if a rear seat entertainment system is installed in your vehicle. To turn the audio system on, push the “MODE” switch.

240

if

the

front audio system

Rear seat audio system— The rear seat audio system is designed for the rear seat passengers to enjoy the audio sound separately between the front seats and the rear seats. The rear seat audio system can be turned on with the rear audio system controller even is off. When the front audio is turned off, the rear audio system will be turned off simul- taneously. The rear passengers can enjoy all the modes (AM and FM radio, cassette tape player and compact disc player with changer) with the rear seat audio system when a cassette tape and a compact disc are loaded in the front audio system. When the same mode is selected on the front and rear audio systems at the same time, the system can be operated on the front audio system. If the radio mode is selected on the front and rear audio systems at the same time, AM and FM modes cannot be changed on the rear seat audio system. You can enjoy the rear seat audio system with commercial headphone. See “—Head- phone input jacks” on page 248 in this Section for details.

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

You can also enjoy the rear seat audio system with a wireless headphone. The wireless headphone can be used within rear seat. If the signal becomes weak, the headphone will mute. For details, refer to the manufacturer’s instructions. With some wireless headphone generally available in the market, it may be difficult to catch sound properly. Toyota recom- mends the use of Toyota genuine wireless headphone. You can purchase a wireless headphone at a Toyota dealer.

05 SIENNA_U (L/O 0409)

CAUTION

D Do not drive with using the head- phone. Otherwise, you may be hard to hear the sound from the outside while using the headphone and may cause an accident.

D With DVD player:

that

Conversational speech on some DVDs is recorded at a low volume to emphasize the impact of sound effects. If you adjust the volume assuming the conversations represent the maximum volume lev- el that the DVD will play, you may be startled by louder sound effects or when you change to a different audio source. Be sure to adjust the volume with this in mind. Make sure the volume creased, before you headphone.

is not turn on

in- the

241

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

The rear seat audio system consists of following components. 1. Volume control knobs 2. Rear seat audio system display 3. Headphone input jacks 4. Front audio system 5. Rear seat audio system controller

—Rear seat audio system controller The rear seat audio system can be oper- ated with the rear seat audio system con- troller.

CAUTION

Do not disassemble or modify the controller. It may cause an accident, fire or electric shock.

NOTICE

Keep the controller away from direct sunlight, high heat and high humidity. These conditions could cause the case to deform or the battery to ex- plode or leak.

242

BEFORE USING THE CONTROLLER (for new vehicle owners) A battery is already set in the control- ler with an insulating sheet, which pre- from being dis- vents charged. Before using the controller, remove the insulating sheet.

the battery

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

USING THE CONTROLLER To use the rear seat audio system con- troller, direct the signal output portion of the controller to the signal reception portion of the rear seat audio system display. The rear seat audio system controller can be operated when the ignition switch is in the “ACC” or “ON” position. The controller does not operate properly when the signal reception portion of the display to direct sunlight. Block the display from direct sunlight. Details of specific buttons, controls, and features see “CONTROLLER FEATURES” on page 244
in this Section.

is exposed

controller,

the

of

CAUTION

To reduce the chance of in case of an accident or a sudden stop while driving, stow the controller in the console box or front seat side table when it is not in use.

injury

NOTICE

Observe the followings, otherwise the controller may be damaged. z Do not drop or strongly knock the

controller against hard objects.

z Do not sit on or place heavy ob-

jects on the controller.

z Do not leave the controller exposed to high temperatures (such as on the long time.

instrument panel) for a

243

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

” and “ ” and “

CONTROLLER FEATURES 1. “ 2. “ 3. “ON/SOURCE” button 4. “OFF” button

” (DISC/CH/PROG) buttons ” (TUNE/TRACK) buttons

1. “

” and “

” (DISC/CH/PROG) but-

tons

the “

” or “

Radio You can scan only the preset stations for the band of the front audio system. (For instructions, see “—Controls and features” on page 223 in this Section.) To scan the preset stations: ” (DISC/CH/PROG) Push button. The radio will tune in the next preset station up or down the band. The station frequency will appear on the dis- play. Cassette tape player Push ” (DISC/CH/PROG) ” or “ button to select the other side of a cas- sette indicates which ” indicates side is currently selected. (“ indicates the bottom the side.) the cassette Auto−reverse player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

tape. The display

feature: After

top side, “

the “

”

244

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

” or “

” or “

” and “

” (TUNE/TRACK) but-

Compact disc player Compact disc changer only— Use this button to select a disc you want to listen to. ” (DISC/CH/PROG) Push the “ button until the number of the disc you want to listen to appears on the display. 2. “ ” (TUNE/TRACK) buttons Radio Push the “ ton to tune or seek. Tuning: ” or “ ” Quickly push and release the “ (TUNE/TRACK) button. Each time you push the button, the radio will step up or down to another frequency. If you push and hold the button, and the radio will go into the seek mode. Seeking: ” (TUNE/ Push and hold the “ TRACK) button. The radio will seek up or down for a station of the nearest frequen- cy and will stop on reception. Each time you push the button, the stations will be searched one after another.

” or “

”

the “

” (TUNE/TRACK) button.

Cassette tape player This button has the following features— To fast forward or reverse: ” (TUNE/TRACK) Push and hold button until “FF” will appears on the dis- play to forward a tape. Push and hold the (TUNE/TRACK) button until “REW” “ appears on the display to rewind a tape. To stop the tape while it is fast forward- ” (TUNE/TRACK) button. To ing, push “ stop the tape while it is rewinding, push “ If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. To skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). ” (TUNE/TRACK) but- Push the “ ton. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button 10 times, the skip feature will be turned off.

” or “

For the skip feature to work correctly a blank space of at least 3 seconds is con- sidered to be a start of a recording. When a beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken, live, or classical re- cordings. Compact disc player This button has the following features— To skip up or down to a different track: ” (TUNE/TRACK) but- Push the “ ton until the number of the track you want to listen to appears on the display. If you the want current track, quickly push ” (TUNE/TRACK) button one time. To fast forward or reverse: ” (TUNE/ Push and hold the “ TRACK) button to fast forward or reverse within a compact disc. When you release the button, the compact disc player will resume playing.

the beginning of

to return to

” or “

” or “

the

“

245

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

3. “ON/SOURCE” button Push “ON/SOURCE” button to turn on the rear seat audio system. Use “ON/SOURCE” button to select an audio mode when the rear seat audio sys- tem is on. Each time you push this but- ton, the system changes between the ra- dio, cassette player and compact disc player. When you change the mode, the display indicates which mode is selected. When a cassette tape and compact discs are not loaded in the front audio system, only a radio mode can be selected in the rear seat audio system. If you push “ON/SOURCE” button to se- lect the casette tape player mode or com- pact disc player mode in that case, a beep sounds from front audio system and “INVALID” for 6
seconds, and then the rear audio system returns to the radio mode. If you push “ON/SOURCE” button while receiving an emergency broadcast, a beep sounds and the screen to indicate that no button can be operated.

“INVALID” appears on

the screen

flashes on

Radio AM mode When you select the AM mode, “AM” will appear on the screen. FM mode When you select the FM mode, “FM1” or “FM2” will appear on the display. If the front audio system receives a traffic the rear seat announcement (TA) while audio system the radio mode, “TRAF” will flash on the screen and the rear seat audio system will turn off. When the traffic an- nouncement (TA), the rear seat audio sys- tem cannot select the AM/FM mode. Tape mode “TAPE” appears on the screen while this mode is selected.

front audio

receives a

in

is

the screen while this

Compact disc mode “CD” appears on mode is selected. The screen shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will screen one of the four following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERR 1”: The disc may be dirty, damaged or (up−side down). Clean the disc and re−insert it. “ERR 3”: There is a problem inside the system. Eject the disc. Set the disc again. “ERR 4”: Over−current. Ask your Toyota dealer to inspect. If the malfunction still exists, take your vehicle to your Toyota dealer. 4. “OFF” button Push “OFF” button to turn off seat audio system.

incorrectly

the rear

inserted

246

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

REPLACING CONTROLLER BATTERY For replacement, use a CR2025 lithium battery or equivalent.

CAUTION

Special care should be that small children do not swallow the re- moved battery or components.

taken

NOTICE

z When replacing the battery, be care-

ful not to lose the components.

z Replace only with

the same or equivalent type of battery recom- mended by a Toyota dealer.

z Dispose of used batteries according

to the local regulations.

Replace the battery by using the following procedures: 1. Pull

the case out while pushing

the

lock release button to the side.

2. Remove the discharged battery. 3. Put in a new battery with the positive

(+) side up. Put in the case securely.

NOTICE

z Make sure that the positive side of the controller battery is facing cor- rectly.

z Do not replace the battery with wet

hands. Water may cause rust.

z Do not touch or move any compo- nents inside of the controller, or it may interfere with proper operation.

247

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

—Headphone input jacks

z Be careful not to bend the electrode of the controller battery insertion and that dust or oil does not ad- here to the transmitter case.

z Close the battery case securely.

After replacing the battery, check that the controller operates properly. If the control- ler still does not operate properly, contact your Toyota dealer.

You can enjoy the rear seat audio sys- tem with commercial headphone. To use the headphones, connect them to the jack. The key must be in the “ACC” or “ON” position.

To adjust the volume of the headphones, turn the knob. Turn right to increase the volume. Turn left to decrease the volume. The maximum volume depends on the type of headphones. The recommended headphone impedance is from 16 Ω to 32 Ω. Please contact your Toyota dealer for fur- ther details.

CAUTION

248

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

Adjust the volume when you connect the headphones jack. Loud sounds may have a significant impact on the human body.

the

to

05 SIENNA_U (L/O 0409)

Rear seat entertainment system—

The rear seat entertainment system con- sists of the following components. 1. Rear seat entertainment system display 2. DVD player 3. Headphone input jacks 4. Headphone volume control dials 5. Front audio system 6. Power outlet main switch 7. Power outlets 8. Input terminal adapter 9. Rear seat entertainment system

controller

249

2005 SIENNA from Sep. ’04 Prod. (OM45431U)

05 SIENNA_U (L/O 0409)

The rear seat entertainment system is de- signed for the rear passengers to enjoy audio and DVD video separately from the