2015 Toyota Prius Owners Manual

539

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

Replacing a flat tire

STEP 1

Chock the tires.

Flat tire Left-hand side Right-hand side Left-hand side Right-hand side

Wheel chock positions

Behind the rear right-hand side tire Behind the rear left-hand side tire In front of the front right-hand side tire In front of the front left-hand side tire

Vehicles with wheel ornament, remove the wheel ornament using the wrench.

To prevent damage, cover the tip of the wrench with a rag.

Front

Rear

STEP 2

540

PRIUS_OM_OM47A17U_DVD_(U)

STEP 3

STEP 4

STEP 5

5-2. Steps to take in an emergency

Slightly loosen the wheel nuts (one turn).

ITO52P108

Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point.

Raise the vehicle until the tire is slightly raised off the ground.

ITO52P112

PRIUS_OM_OM47A17U_DVD_(U)

541

5-2. Steps to take in an emergency

STEP 6

ITO52P114

Installing the spare tire

STEP 1

Remove all the wheel nuts and the tire.

When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.

Remove any dirt or foreign mat- ter from the wheel contact sur- face.

If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.

STEP 2

Install the tire and loosely tighten each wheel nut by hand by approximately the same amount.

542

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

Replacing an aluminum wheel with a compact spare tire

Tapered portion

Tighten the nuts until the tapered portion comes into loose contact with the disc wheel seat.

Disc wheel seat

Replacing an aluminum wheel with an aluminum wheel

Disc wheel

Turn the nut washers until they come into contact with the disc wheel.

Washer

543

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

STEP 3

Lower the vehicle.

STEP 4

STEP 5

ITO52P119

ITO52P120

Firmly tighten each nut two or three times in the order shown in the illustration.

Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)

Vehicles with wheel ornament, reinstall the wheel ornament.*

Align the cutout of the wheel ornament with the valve stem as shown. *: The wheel ornament cannot be installed on the compact spare tire. Stow the flat tire, the tire jack and all tools.

STEP 6

544

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

■The compact spare tire

●The compact spare tire is identified by the label “TEMPORARY USE

ONLY” on the tire sidewall. Use the compact spare tire temporarily, and only in an emergency.

●Make sure to check the tire inflation pressure of the compact spare

tire. (P. 581)

■After completing the tire change

The tire pressure warning system must be reset. (P. 448)

■When using the compact spare tire

As the compact spare tire is not equipped with a tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be indicated by the tire pressure warning system. Also, if you replace the compact spare tire after the tire pressure warning light comes on, the light remains on.

■If you have a flat front tire on a road covered with snow or ice

Install the compact spare tire on one of the rear wheels of the vehicle. Perform the following steps and fit tire chains to the front tires:

STEP 1

STEP 2

STEP 3

Replace a rear tire with the compact spare tire. Replace the flat front tire with the tire removed from the rear of the vehicle. Fit tire chains to the front tires.

■Jack point guide

The jack point guides are located under the rocker panel. They indicate the jack point positions.

545

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■When using the compact spare tire

●Remember that the spare tire provided is specifically designed for use

with your vehicle. Do not use your spare tire on another vehicle.

●Do not use more than one spare tire simultaneously. ●Replace the spare tire with a standard tire as soon as possible. ●Avoid sudden acceleration, deceleration and braking, as well as sharp

cornering.

■When storing the compact spare tire

Be careful not to catch fingers or other body parts between the compact spare tire and the body of the vehicle.

■When the compact spare tire is attached

The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ●ABS & Brake assist ●VSC ●TRAC ●Cruise control (if equipped) ●Dynamic radar cruise control (if equipped) ●Pre-collision system (if equipped) ●LKA (Lane-Keeping Assist) (if equipped) ●EPS ●Rear view monitor system (if equipped) ●Advanced parking guidance system (if equipped) ●Navigation system (if equipped)

546

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■Speed limit when using the compact spare tire

Do not drive at speeds in excess of 50 mph (80 km/h) when a compact spare tire is installed on the vehicle. The compact spare tire is not designed for driving at high speeds. Failure to observe this precaution may lead to an accident causing death or seri- ous injury.

■Using the tire jack

Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. Observe the following precautions: ●Do not use the tire jack for any purpose other than replacing tires or

installing and removing tire chains.

●Only use the tire jack that comes with this vehicle for replacing a flat

tire. Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.

●Always check that the tire jack is securely set to the jack point. ●Do not put any part of your body under the vehicle while it is supported

by the jack.

●Do not start or run the hybrid system while your vehicle is supported by

the jack.

●Do not raise the vehicle while someone is inside. ●When raising the vehicle, do not put an object on or under the jack. ●Do not raise the vehicle to a height greater than that required to

replace the tire.

●Use a jack stand if it is necessary to get under the vehicle. Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle may be injured.

547

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■Replacing a flat tire

●Do not touch the disc wheels or the area around the brakes immedi-

ately after the vehicle has been driven. After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc. may result in burns.

●Failure to follow these precautions could cause the wheel nuts to

loosen and the tire to fall off, resulting in death or serious injury. • Have the wheel nuts tightened with a torque wrench to 76 ft•lbf (103

N•m, 10.5 kgf•m) as soon as possible after changing wheels.

• When installing a tire, only use wheel nuts that have been specifi-

cally designed for that wheel.

• If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer.

• When installing the wheel nuts, be sure to install the wheel nuts

with the tapered ends facing inward. (P. 462)

■After using the tools and jack

Before driving, make sure all the tools and jack are securely in place in their storage location to reduce the possibility of personal injury during a collision or sudden braking.

548

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

NOTICE

■Do not drive the vehicle with a flat tire

Do not continue driving with a flat tire. Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.

■Be careful when driving over bumps with the compact spare tire

installed on the vehicle The vehicle becomes lower when driving with the compact spare tire compared to when driving with standard tires. Be careful when driving over uneven road surfaces.

■Driving with tire chains and the compact spare tire

Do not fit tire chains to the compact spare tire. Tire chains may damage the vehicle body and adversely affect driving performance.

■When replacing the tires

When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. ■To avoid damage to the tire pressure warning valves and transmit-

ters When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (P. 447)

549

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If the hybrid system will not start

Reasons for the hybrid system not starting vary depending on the situation. Check the following and perform the appropriate proce- dure: ■ The hybrid system will not start even though the correct

starting procedure is being followed (P. 195) One of the following may be the cause of the problem: ● The electronic key may not be functioning properly.*

(P. 553)

● There may not be sufficient fuel in the vehicle’s tank.

Refuel the vehicle. (P. 40)

● There may be a malfunction in the immobilizer system.*

(P. 137)

● There may be a malfunction in the shift control system.*

(P. 200, 519)

*: It may not be possible to shift the shift position from P to other posi-

tion.

■ The interior lights and headlights are dim, or the horn does

not sound or sounds at a low volume One of the following may be the cause of the problem: ● The 12-volt battery may be discharged. (P. 555) ● The 12-volt battery terminal connections may be loose or cor-

roded.

550

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

■ The interior lights and headlights do not turn on, or the horn

does not sound One of the following may be the cause of the problem: ● One or both of the 12-volt battery terminals may be discon-

nected.

● The 12-volt battery may be discharged. (P. 555) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.

Emergency start function

When the hybrid system does not start, the following steps can be used as an interim measure to start the hybrid system if the “POWER” switch is functioning normally:

STEP 1

STEP 2

STEP 3

Set the parking brake. Turn the “POWER” switch to ACCESSORY mode. Press and hold the “POWER” switch for about 15 seconds while depressing the brake pedal firmly.

Even if the hybrid system can be started using the above steps, the system may be malfunctioning. Have the vehicle inspected by your Toyota dealer.

551

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If you lose your keys

New genuine keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate.

552

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If the electronic key does not operate properly

If communication between the electronic key and vehicle is inter- rupted (P. 73) or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote con- trol cannot be used. In such cases, the doors can be opened and the hybrid system can be started by following the procedure below.

Locking and unlocking the doors

Use the mechanical key (P. 60) in order to perform the following operations:

Locks all the doors Unlocks the door Turning the key rearward unlocks the driver’s door. Turning the key once again within 3 seconds unlocks the other doors.

ITO52P121

553

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

Starting the hybrid system

STEP 1

Depress the brake pedal.

STEP 2

Touch the Toyota emblem side of the electronic the “POWER” switch.

key

to

If any of the doors is opened or closed while the key is being touched to the switch, an alarm will sound to indicate that the start function cannot detect the elec- tronic key.

STEP 3

Press the “POWER” switch within 10 seconds of the buzzer sounding, keeping the brake pedal depressed.

In the event that the hybrid system still cannot be operated, contact your Toyota dealer.

■Stopping the hybrid system

Set the parking brake, shift the shift position to P and press the “POWER” switch as you normally do when stopping the hybrid system.

■Replacing the key battery

As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery is depleted. (P. 464)

■Changing “POWER” switch modes

Within 10 seconds of the buzzer sounding, release the brake pedal and press the “POWER” switch. The hybrid system does not start and modes will be changed each time the switch is pressed. (P. 197)

554

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If the 12-volt battery is discharged

The following procedures may be used to start the hybrid system if the vehicle’s 12-volt battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your vehicle by follow- ing the steps below.

STEP 1

STEP 2

Open the hood and fuse block cover.

When closing, first hook the lid onto the two rear tabs.

ITO43P127

Open the exclusive jump start- ing terminal cover.

555

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

STEP 3

Connect the jumper cables according to the following procedure:

Connect a positive jumper cable clamp to the exclusive jump starting terminal on your vehicle. Connect the clamp on the other end of the positive cable to the positive (+) battery terminal on the second vehicle. Connect a negative cable clamp to the negative (-) battery termi- nal on the second vehicle. Connect the clamp at the other end of the negative cable to a solid, stationary, unpainted metallic point away from the exclu- sive jump starting terminal and any moving parts, as shown in the illustration.

556

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

STEP 4

STEP 5

STEP 6

STEP 7

STEP 8

Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5 minutes to recharge the battery of your vehicle. Maintain the engine speed of the second vehicle and start the hybrid system of your vehicle by turning the “POWER” switch to ON mode. Make sure the “READY” indicator comes on. If the indicator light does not come on, contact your Toyota dealer. Once the hybrid system has started, remove the jumper cables in the exact reverse order from which they were con- nected. Close the exclusive jump starting terminal cover, and rein- stall the fuse box cover to its original position. When installing, first hook the fuse box cover onto the two rear tabs.

Once the hybrid system starts, have the vehicle inspected at your Toyota dealer as soon as possible.

557

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

■Starting the hybrid system when the 12-volt battery is discharged

The hybrid system cannot be started by push-starting.

■To prevent 12-volt battery discharge

●Turn off the headlights and the audio system while the hybrid system is

off.

●Turn off any unnecessary electrical components when the vehicle is run-

ning at a low speed for an extended period, such as in heavy traffic.

■When the 12-volt battery is removed or discharged

●The hybrid system may not start. (P. 442) ●If the 12-volt battery is depleted with the shift position in P, it will not be possible to shift the shift position other than P. In this case, the vehicle cannot be towed without lifting both front wheels because the front wheels are locked by the parking lock. (P. 495)

●When the 12-volt battery is reconnected, start the hybrid system, depress the brake pedal, and confirm that it is possible to shift into each shift posi- tion.

■Charging the 12-volt battery

The electricity stored in the 12-volt battery will discharge gradually even when the vehicle is not in use, due to natural discharge and the draining effects of certain electrical appliances. If the vehicle is left for a long time, the 12-volt battery may discharge, and the hybrid system may be unable to start. (The 12-volt battery recharges automatically while the hybrid system is oper- ating.)

558

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■Avoiding 12-volt battery fires or explosions

Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the 12-volt battery: ●Make sure each jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any other than the intended terminal. ●Do not allow the other end of the jumper cable connected to the “+” termi- nal to come into contact with any other parts or metal surfaces in the area, such as brackets or unpainted metal.

●Do not allow the + and - clamps of the jumper cables to come into contact

with each other.

●Do not smoke, use matches, cigarette lighters or allow open flame near

the 12-volt battery.

■12-volt battery precautions

The 12-volt battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following precautions when handling the 12-volt battery: ●When working with the 12-volt battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.

●Do not lean over the 12-volt battery. ●In the event that battery fluid comes into contact with the skin or eyes, immediately wash the affected area with water and seek medical attention. Place a wet sponge or cloth over the affected area until medical attention can be received.

●Always wash your hands after handling the battery support, terminals, and

other battery-related parts.

●Do not allow children near the 12-volt battery.

559

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■After recharging the 12-volt battery

Have the 12-volt battery inspected at your Toyota dealer as soon as possi- ble. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a malodorous gas, which may be detrimental to the health of passengers.

■When replacing the 12-volt battery

P. 444

NOTICE

■When handling jumper cables

When connecting the jumper cables, ensure that they do not become entan- gled in the cooling fans, etc.

■Exclusive jump starting terminal

The exclusive jump starting terminal is to be used when charging the 12-volt battery from another vehicle in an emergency. It cannot be used to jump start another vehicle.

560

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If your vehicle overheats

The following may indicate that your vehicle is overheating. ● The high coolant temperature warning light (P. 504) comes on or flashes, or a loss of hybrid system power is experienced. (For example, the vehicle speed does not increase.)

● “HYBRID SYSTEM OVERHEAT” (P. 525) is shown on the

multi-information display.

● Steam comes out from under the hood.

Correction procedures

■ If the high coolant temperature warning light comes on or

flashes

STEP 1

STEP 2

Stop the vehicle in a safe place and turn off the air condition- ing system, and then stop the hybrid system. If you see steam:

Carefully lift the hood after the steam subsides.

If you do not see steam: Carefully lift the hood.

STEP 3

After the hybrid system has cooled down sufficiently, inspect the hoses and radiator core (radiator) for any leaks.

Radiator Cooling fans If a large amount of coolant leaks, immediately contact your Toyota dealer.

561

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

STEP 4

STEP 5

ITO43P111

The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir.

Reservoir “FULL” “LOW”

Add coolant if necessary.

Water can be used in an emer- gency if coolant is unavailable.

STEP 6

STEP 7

ITO52P130

Start the hybrid system and turn the air conditioning system on to check that the radiator cooling fans operate and to check for coolant leaks from the radiator or hoses. The fans operate when the air conditioning system is turned on immediately after a cold start. Confirm that the fans are operating by checking the fan sound and air flow. If it is difficult to check these, turn the air conditioning system on and off repeatedly. (The fans may not operate in freezing temperatures.) If the fans are not operating:

Stop the hybrid system immediately and contact your Toyota dealer.

If the fans are operating:

Have the vehicle inspected at the nearest Toyota dealer.

562

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

■ If “HYBRID SYSTEM OVERHEAT” is shown on the multi-infor-

mation display

STEP 1

STEP 2

Stop the vehicle in a safe place. Stop the hybrid system and carefully lift the hood.

STEP 3

STEP 4

After the hybrid system has cooled down, inspect the hoses and radiator core (radiator) for any leaks. Radiator Cooling fans If a large amount of coolant leaks, immediately contact your Toyota dealer.

The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir.

Reservoir “F” “L”

563

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

STEP 5

Add coolant if necessary.

Water can be used in an emer- gency if coolant is unavailable. If water was added in an emer- gency, have the vehicle inspected at your Toyota dealer as soon as possible.

STEP 6

After stopping the hybrid system and waiting for 5 minutes or more, start the hybrid system again and check the multi-infor- mation display. If the message does not disappear:

Stop the hybrid system and contact your Toyota dealer.

If the message is not displayed:

The hybrid system temperature has dropped and the vehicle may be driven normally. However, if the message appears again frequently, contact your Toyota dealer.

564

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

CAUTION

■To prevent an accident or injury when inspecting under the hood of

your vehicle ●If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, caus- ing serious injuries such as burns.

●After the hybrid system has been turned off, check that the indicator on the

“POWER” switch and the “READY” indicator are off. When the hybrid system is operating, the gasoline engine may automati- cally start, or the cooling fans may suddenly operate even if the gasoline engine stops. Do not touch or approach rotating parts such as the fans, which may lead to fingers or clothing (especially a tie, a scarf or a muffler) getting caught, resulting in serious injury.

●Do not loosen the coolant reservoir cap while the hybrid system and radia-

tor are hot. Serious injury, such as burns, may result from hot coolant and steam released under pressure.

565

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

NOTICE

■When adding engine/power control unit coolant

Wait until the hybrid system has cooled down before adding engine/power control unit coolant. When adding coolant, do so slowly. Adding cool coolant to a hot hybrid sys- tem too quickly can cause damage to the hybrid system.

■To prevent damage to the cooling system

Observe the following precautions: ●Avoid contaminating the coolant with foreign matter (such as sand or dust

etc.).

●Do not use any coolant additives.

566

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If the vehicle becomes stuck

Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow:

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

Set the parking brake and shift the shift position to P. Stop the hybrid system. Remove the mud, snow or sand from around the stuck tire. Place wood, stones or some other material under the tires to help provide traction. Restart the hybrid system. Shift the shift position to D or R, release the parking brake and carefully apply the accelerator to free the vehicle.

CAUTION

■When attempting to free a stuck vehicle

If you choose to push the vehicle back and forth to free it, make sure the sur- rounding area is clear to avoid striking other vehicles, objects or people. The vehicle may also lunge forward or lunge back suddenly as it becomes free. Use extreme caution.

■When changing the shift position

Be careful not to change the shift position with the accelerator pedal depressed. Changing the shift position to any positions other than P or N may cause the vehicle to accelerate abruptly, causing an accident and resulting in death or serious injury.

567

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency

NOTICE

■To avoid damage to the hybrid transmission and other components

●Avoid spinning the wheels and depressing the accelerator pedal more

than necessary.

●If the vehicle remains stuck even after these procedures are performed,

the vehicle may require towing to be freed.

568

PRIUS_OM_OM47A17U_DVD_(U)

5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency

Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure:

STEP 1

Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle. Shift the shift position to N. If the shift position is shifted to N

STEP 2

STEP 3

STEP 4

After slowing down, stop the vehicle in a safe place by the road. Stop the hybrid system.

If the shift position cannot be shifted to N

STEP 3

Keep depressing the brake pedal with both feet to reduce vehicle speed as much as possible.

STEP 4

Press and hold for 2 seconds or more, or

press briefly for 3 times or more

To stop the hybrid system, press and hold the “POWER” switch for 2 consecutive sec- onds or more, or press it briefly for 3 times or more in succession.

STEP 5

Stop the vehicle in a safe place by the road.

PRIUS_OM_OM47A17U_DVD_(U)

569

5-2. Steps to take in an emergency

CAUTION

■If the hybrid system has to be turned off while driving

Power assist for the steering will be lost, making the steering wheel heavier to turn. Decelerate as much as possible before turning off the hybrid system.

570

PRIUS_OM_OM47A17U_DVD_(U)

Vehicle specifications

6-1. Specifications

Maintenance data (fuel, oil level, etc.)......... 572
Fuel information ............... 583
Tire information ................ 587

6-2. Customization

Customizable features ..... 602

6-3.

Initialization Items to initialize .............. 609

571

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications Maintenance data (fuel, oil level, etc.)

Dimensions and weight

Overall length Overall width Overall height*1

Wheelbase

Tread

Front

Rear

Vehicle capacity weight (Occupants + luggage)

176.4 in. (4480 mm) 68.7 in. (1745 mm) 58.7 in. (1490 mm)*2
59.3 in. (1505 mm)*3
106.3 in. (2700 mm) 60.0 in. (1525 mm)*4
59.6 in. (1515 mm)*5
59.8 in. (1520 mm)*4
59.4 in. (1510 mm)*5

825 lb. (370 kg)

*1: Unladen vehicle *2: Vehicles without moon roof with Solar Panel *3: Vehicles with moon roof with Solar Panel *4: Vehicles with 15-inch tires *5: Vehicles with 17-inch tires

572

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Vehicle identification

■ Vehicle identification number

The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

This number is stamped on the top left of the instrument panel.

ITO61P101

This number is also on the Certi- fication Label.

This number is also stamped under the right-hand front seat.

573

PRIUS_OM_OM47A17U_DVD_(U)

The engine number is stamped on the engine block as shown.

1.8 L 4-cylinder (2ZR-FXE) 4-cylinder in line, 4-cycle, gasoline 3.17  3.48 in. (80.5  88.3 mm) 109.7 cu.in. (1798 cm3)

Automatic adjustment

Unleaded gasoline only 87 (Research Octane Number 91) or higher

11.9 gal. (45 L, 9.9 Imp.gal.)

6-1. Specifications

■ Engine number

Engine

Model Type Bore and stroke Displacement Valve clearance (engine cold)

Fuel

Fuel type Octane Rating Fuel tank capacity (Reference)

574

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Electric motor (Traction motor)

Type Maximum output Maximum torque

Permanent magnet motor 60 kW 153 ft•lbf (207 N•m, 21.1 kgf•m)

Hybrid battery (traction battery)

Type Voltage Capacity Quantity Overall voltage

Nickel-Metal hydride battery 7.2 V/module 6.5 Ah (3HR) 28 modules 201.6 V

Lubrication system

Oil capacity (Drain and refill  reference*) With filter Without filter

4.4 qt. (4.2 L, 3.7 Imp.qt.) 4.1 qt. (3.9 L, 3.4 Imp.qt.)

*: The engine oil capacity is a reference quantity to be used when changing the engine oil. Warm up the engine and turn off the hybrid system, wait more than 5 minutes, and check the oil level on the dipstick.

575

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil Recommended viscosity: SAE 0W-20

SAE 0W-20 is the best choice for good fuel economy and good starting in cold weather. If SAE 0W-20 is not available, SAE 5W-20 oil may be used. However, it must be replaced with SAE 0W-20 at the next oil change.

Outside temperature

Oil viscosity (0W-20 is explained here as an example): • The 0W in 0W-20 indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

• The 20 in 0W-20 indicates the viscosity characteristic of the oil when the oil is at high temperature. An oil with a higher viscosity (one with a higher value) may be better suited if the vehicle is oper- ated at high speeds, or under extreme load conditions.

576

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

How to read oil container label: The International Lubricant Specification Advisory Committee (ILSAC) Certification Mark is added to some oil containers to help you select the oil you should use.

577

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Cooling system

Capacity

Gasoline engine

Power control unit

Coolant type

Ignition system

Spark plug Make Gap

NOTICE

Without an exhaust heat recovery system 6.9 qt. (6.5 L, 5.7 Imp.qt.) With an exhaust heat recovery system 7.6 qt. (7.2 L, 6.3 Imp.qt.)

2.2 qt. (2.1 L, 1.8 Imp.qt.)

Use either of the following: • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non- silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technol- ogy Do not use plain water alone.

DENSO SC20HR11 0.043 in. (1.1 mm)

■Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust the spark plug gap.

578

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Electrical system

12-volt battery Open voltage*1 at 68°F (20°C):

Charging rates

Fully charged Half charged Discharged

12.5 V or over 11.0  12.5 V Under 11.0 V 5 A max.

*1: Voltage is checked 30 seconds after the hybrid system and all lights are

turned off.

Transmission

Fluid capacity*2
Fluid type

3.6 qt. (3.4 L, 3.0 Imp.qt.) Toyota Genuine ATF WS

*2: The fluid capacity is the quantity of reference.

If replacement is necessary, contact your Toyota dealer.

NOTICE

■Transmission fluid type

Using transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.

579

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Brakes

Pedal clearance*1
Pedal free play Brake pad wear limit Parking brake lining wear limit Parking brake pedal travel*2
Fluid type

3.03 in. (77 mm) Min. 0.04  0.24 in. (1.0  6.0 mm) 0.04 in. (1.0 mm) 0.04 in. (1.0 mm)

8 11 clicks

SAE J1703 or FMVSS No. 116 DOT 3

*1: Minimum pedal clearance when depressed with a force of 44.1 lbf (196 N,

20.0 kgf) while the hybrid system is operating.

*2: Parking brake pedal travel when depressed with a force of 67.5 lbf (300 N,

30.6 kgf).

Steering

Free play

Less than 1.2 in. (30 mm)

580

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

P195/65R15 89S Front tire 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear tire 33 psi (230 kPa, 2.3 kgf/cm2 or bar) 15  6J 76 ft•lbf (103 N•m, 10.5 kgf•m)

P215/45R17 87V Front tire 33 psi (230 kPa, 2.3 kgf/cm2 or bar) Rear tire 32 psi (220 kPa, 2.2 kgf/cm2 or bar) 17  7J 76 ft•lbf (103 N•m, 10.5 kgf•m)

T135/80D16 101M

60 psi (420 kPa, 4.2 kgf/cm2 or bar)

16  4T 76 ft•lbf (103 N•m, 10.5 kgf•m)

581

Tires and wheels

Type A Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

Type B Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

Compact spare tire Tire size Spare tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

H11
9005

9005
H16

WY21W W5W

W5W

WY21W W21W W5W











Halogen headlights Low beam High beam LED headlights High beam Fog lights* Front turn signal lights Front side marker lights Parking lights (halogen headlights) Rear turn signal lights Back-up lights License plate lights Front interior/personal lights Rear interior light Vanity lights Door courtesy lights Luggage compartment light

Exterior

Interior

A: H11 halogen bulbs B: HB3 halogen bulbs C: H16 halogen bulbs D: Wedge base bulbs (amber) E: Wedge base bulbs (clear) F: Double end bulbs *:

If equipped

55
60

60
19
21

21
21

Type

582

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications Fuel information

You must only use unleaded gasoline in your vehicle. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A..

■Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your vehicle has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

■Gasoline quality

In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

583

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

■Gasoline quality standards

●Automotive manufacturers in the U.S.A., Europe and Japan have devel- oped a specification for fuel quality called the World-Wide Fuel Charter (WWFC), which is expected to be applied worldwide.

●The WWFC consists of four categories that are based on required emis-

sion levels. In the U.S., category 4 has been adopted.

●The WWFC improves air quality by lowering emissions in vehicle fleets,

and improves customer satisfaction through better performance.

■Recommendation of the use of gasoline containing detergent additives ●Toyota recommends the use of gasoline that contains detergent additives

to avoid the build-up of engine deposits.

●All gasoline sold in the U.S.A. contains minimum detergent additives to clean and/or keep clean intake systems, per EPA’s lowest additives con- centration program.

●Toyota strongly recommends the use of Top Tier Detergent Gasoline. For more information on Top Tier Detergent Gasoline and a list of marketers, please go to the official website www.toptiergas.com.

■Recommendation of the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

584

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

■Non-recommendation of the use of blended gasoline

DO NOT use gasoline containing more than 15% ethanol.

(30% ethanol)

(50% ethanol)

(85% ethanol)

●Use only gasoline containing up to 15%

ethanol. DO NOT use any flex-fuel or gasoline that could contain more than 15% etha- nol, including from any pump labeled E30, E50, E85 (which are only some examples of fuel containing more than 15% ethanol).

●If you use gasohol in your vehicle, be sure that it has an octane rating no

lower than 87.

●Toyota does not recommend the use of gasoline containing methanol.

■Non-recommendation of the use of gasoline containing MMT

Some gasoline contains an octane enhancing additive called MMT (Methyl- cyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

■If your engine knocks

●Consult your Toyota dealer. ●You may occasionally notice light knocking for a short time while acceler-

ating or driving uphill. This is normal and there is no need for concern.

585

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

NOTICE

■Notice on fuel quality

●Do not use improper fuels. If improper fuels are used, the engine will be

damaged.

●Do not use leaded gasoline.

Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.

●Do not use gasohol other than the type previously stated.

Other gasohol may cause fuel system damage or vehicle performance problems.

●Using unleaded gasoline with an octane number or rating lower than the

level previously stated will cause persistent heavy knocking. At worst, this will lead to engine damage.

■Fuel-related poor driveability

If poor driveability is encountered after using a different type of fuel (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

■When refueling with gasohol

Take care not to spill gasohol. It can damage your vehicle’s paint.

586

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications Tire information

Typical tire symbols Full-size tire

Compact spare tire

Tire size DOT and Tire Identification Number (TIN) Location of treadwear indicators

ITO61P105

(P. 590) (P. 589) (P. 446)

587

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Summer tires or all season tires (P. 451) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly put into the tire. A tube type tire has a tube inside the tire and the tube main- tains the air pressure. Load limit at maximum cold tire inflation pressure Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. “TEMPORARY USE ONLY” A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded on its sidewall. This tire is designed for temporary emergency use only.

(P. 451) (P. 581)

588

PRIUS_OM_OM47A17U_DVD_(U)

6-1. Specifications

Typical DOT and Tire Identification Number (TIN)

Identification Number