2012 Toyota Prius Owners Manual

Up Pull the head restraints up. Down Push and hold the lock release button when lowering the head restraint.

Up Down Pull up or push down the head restraint while pressing the lock release button.

To fold Pull the head restraint up while pressing the lock release but- ton. To use Lift up and push down the head restraint to the lowest lock position.

105

1-4. Adjustable components (seats, mirrors, steering wheel)

■Removing the head restraints

Front and rear center seats

Lock release button

Pull the head restraint up while pressing the lock release button.

Foldable type rear outside seats

Pull the head restraint up while pressing the lock release buttons.

Lock release buttons

Non-foldable type rear outside seats

Pull the head restraint up while pressing the lock release button.

Lock release button

106

1-4. Adjustable components (seats, mirrors, steering wheel)

■Installing the head restraints

Front and rear center seats

Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.

Lock release button

Rear outside seats

Align the head restraint with the installa- tion holes and push it down to the lowest lock position.

■Adjusting the height of the head restraints

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

■Adjusting the rear center seat head restraint

Always raise the head restraint one level from the stowed position when using.

107

1-4. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Head restraint precautions

Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure

they are locked in position.

●Do not drive with the head restraints removed.

108

1

1-4. Adjustable components (seats, mirrors, steering wheel) Seat belts

Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts

● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.

● Position the lap belt as low

as possible over the hips.

● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.

■ Fastening and releasing the seat belt

To fasten the seat belt, push the plate into the buckle until a click sound is heard. To release the seat belt, press the release button.

Release button

109

1-4. Adjustable components (seats, mirrors, steering wheel)

■ Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.

Seat belt pretensioners (front seats)

The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.

The pretensioner does not acti- vate in the event of a minor frontal impact, a side impact, a rear impact or a vehicle rollover.

110

1-4. Adjustable components (seats, mirrors, steering wheel)

Pre-collision seat belts (front seats of vehicles with pre-collision system)

If the system determines that a collision is unavoidable, the front seat belts will retract before the collision. (→P. 303)

■Emergency locking retractor (ELR)

The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.

■Automatic locking retractor (ALR)

When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (→P. 165)

■Child seat belt usage

The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (→P. 160) ●When the child becomes large enough to properly wear the vehicle’s

seat belt, follow the instructions on P. 109 regarding seat belt usage.

■Replacing the belt after the pretensioner has been activated

If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.

111

1-4. Adjustable components (seats, mirrors, steering wheel)

■Seat belt extender

If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.

they are not

CAUTION

Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or serious injury. ■Wearing a seat belt

●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt

for more than one person at once, including children.

●Toyota recommends that children be seated in the rear seat and always

use a seat belt and/or an appropriate child restraint system.

●To achieve a proper seating position, do not recline the seat more than necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.

●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips. ●When using the rear outside seat belts, make sure that the belt pass

through the guide.

112

1

1-4. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Pregnant women

Obtain medical advice and wear the seat belt in the proper way. (→P. 109) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only the pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a colli- sion.

■People suffering illness

Obtain medical advice and wear the seat belt in the proper way. (→P. 109)

113

1-4. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When children are in the vehicle

Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

■Seat belt pretensioners

●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.

●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.

■Adjustable shoulder anchor

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (→P. 110)

114

1-4. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Seat belt damage and wear

●Do not damage the seat belts by allowing the belt, plate, or buckle to be

jammed in the door.

●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.

●Ensure that the belt and plate are locked and the belt is not twisted.

If the seat belt does not function correctly, immediately contact your Toyota dealer.

●Replace the seat assembly, including the belts, if your vehicle has been

involved in a serious accident, even if there’s no obvious damage.

●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.

115

1-4. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Using a seat belt extender

●Do not wear the seat belt extender if you can fasten the seat belt without

the extender.

●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.

●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.

NOTICE

■When using a seat belt extender

When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.

116

1-4. Adjustable components (seats, mirrors, steering wheel) Steering wheel

The steering wheel can be adjusted to a comfortable position.

STEP 1

STEP 2

Hold the steering wheel and push the lever down.

Adjust to the ideal position by moving the steering wheel horizontally and vertically.

After adjustment, pull the lever up the steering wheel.

to secure

CAUTION

■Caution while driving

Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury.

117

1-4. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror

The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver’s seating posture.

Adjusting the height of rear view mirror

Adjust the height of the rear view mirror by moving it up and down.

Anti-glare function

ITI14P209

Manual anti-glare inside rear view mirror Reflected light from the headlights of vehicles behind can be reduced by operating the lever.

Normal position Anti-glare position

118

1

1-4. Adjustable components (seats, mirrors, steering wheel)

Auto anti-glare inside rear view mirror (without garage door opener) Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced.

Indicator

Changing automatic anti-glare function mode ON/OFF

When the automatic anti-glare function is in ON mode, the indi- cator illuminates. The function will set to ON mode each time the “POWER” switch is turned to ON mode. Pressing the button turns the function to OFF mode. (The indi- cator also turns off.)

Auto anti-glare inside rear view mirror (with garage door opener) Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced.

Indicator

Changing automatic anti-glare function mode

ON OFF When the automatic anti-glare function is in ON mode, the indi- cator illuminates. The function will set to ON mode each time the “POWER” switch is turned to ON mode. Turns the function to OFF mode, the indicator turns off.

119

1-4. Adjustable components (seats, mirrors, steering wheel)

■To prevent sensor error (vehicles with auto anti-glare inside rear view

mirror) Without garage door opener

To ensure that the sensors operate prop- erly, do not touch or cover them.

With garage door opener

CAUTION

■Caution while driving

Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.

120

1-4. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors

Mirror angle can be adjusted using the switch.

STEP 1

STEP 2

To select a mirror to adjust, press the switch.

Left Right

To adjust the mirror, press the switch.

Up Right Down Left

Folding the mirrors

Push the mirror back in the direc- tion of the vehicle’s rear.

121

1-4. Adjustable components (seats, mirrors, steering wheel)

■Mirror angle can be adjusted when

The “POWER” switch is in ACCESSORY or ON mode.

■When the mirrors are fogged up (vehicles with outside rear view mirror

defoggers) The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defoggers. (→P. 346)

CAUTION

■When driving the vehicle

Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly

adjusted before driving. ■When a mirror is moving

To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.

■When the mirror defoggers are operating (vehicles with outside rear

view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

122

1

1-5. Opening and closing the windows and moon roof Power windows

The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:

One-touch closing* Closing One-touch opening* Opening *: Pushing

the switch

the opposite direction will stop win- dow travel partway.

in

Window lock switch

Press the switch down to lock the passenger windows.

Use this switch to prevent chil- dren from accidentally opening or closing a passenger window. Press the switch again to unlock the passenger windows.

■The power windows can be operated when

The “POWER” switch is in ON mode.

123

1-5. Opening and closing the windows and moon roof

■Operating the power windows after turning the hybrid system off

The power windows can be operated for approximately 45 seconds even after the “POWER” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.

■Jam protection function

If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.

■When the power window does not close normally

If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the relevant door. ●After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the “POWER” switch is turned to ON mode.

●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.

STEP 1

STEP 2

STEP 3

Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.

If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

124

1-5. Opening and closing the windows and moon roof

■Customization

The one-touch closing operation can be disabled, except for the driver’s seat. (Customizable features →P. 590)

CAUTION

■Closing the windows

Observe the following precautions. Failing to do so may result in death or serious injury.

●Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.

●Do not allow children to operate the

power windows. Closing a power window on someone can cause serious injury, and in some instances, even death.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the window fully closes.

125

1-5. Opening and closing the windows and moon roof Moon roof with Solar Panel∗

Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Open

Tilt up Push “OPEN”. The moon roof will open after pausing at the tilt up position, when pushing and holding the switch. To tilt down, push and hold “CLOSE”. Open Push “OPEN” at the tilt up position. Lightly push on either side of the switch stops the moon roof partway. The moon roof stops slightly before the fully open position to reduce the wind noise. Push “OPEN” again to fully open.

126

∗: If equipped

1-5. Opening and closing the windows and moon roof

■ Close

Push and hold “CLOSE”.

The moon roof stops once. Push and hold the switch again to fully close.

■The moon roof can be operated when

The “POWER” switch is in ON mode.

■Operating the moon roof after turning the hybrid system OFF

The moon roof can be operated for approximately 45 seconds even after the “POWER” switch is turned to ACCESSORY mode or turned OFF. It cannot, however, be operated once either front door is opened.

127

1-5. Opening and closing the windows and moon roof

■Jam protection function

If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.

■To reduce moon roof wind noise

When the moon roof is opened automatically, it will stop slightly before the fully open position. Driving with the moon roof in this position can help reduce wind noise.

■Sunshade

The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.

■Solar Panel

The solar panel contains solar cells, and produces energy to operate the Solar Ventilation System by receiving sunlight.

■Moon roof open warning buzzer

The buzzer sounds when the “POWER” switch is turned off and the driver’s door is opened with the moon roof open.

■If the moon roof cannot be closed

If the moon roof cannot be closed, such as when the jam protection function activates accidentally due to a malfunction, pressing and holding “CLOSE” switch closes the moon roof. After this, to make the automatic opening function and jam protection func- tion available again, press and hold the “OPEN” switch until the moon roof opens fully and then closes slightly. If the functions do not activate, contact your Toyota dealer.

128

1

1-5. Opening and closing the windows and moon roof

CAUTION

■Opening the moon roof

Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-

cle while it is moving.

●Do not sit on top of the moon roof.

■Closing the moon roof

Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.

●Do not allow children to operate the moon roof.

Closing the moon roof on someone can cause death or serious injury.

■Jam protection function

●Never try jamming any part of your body to activate the jam protection

function intentionally.

●The jam protection function may not work if something gets caught just

before the moon roof fully closes.

■Precautions for moon roof with Solar Panel

Be careful not to touch the solar panel surface in scorching sun weather con- ditions as it will rise very high in temperature and may cause burns.

129

1-5. Opening and closing the windows and moon roof

NOTICE

■To prevent damage to the moon roof

●Before opening, make sure that there are no foreign objects such as

stones or ice around the opening.

●Do not hit the face or edge of the moon roof with hard objects. ●Do not continue to press and hold the switch after the moon roof has

opened or closed completely.

■Operating the moon roof

There is the possibility that water or rain will get into the vehicle if you oper- ate the moon roof after a rainfall, snowfall or car wash. Wipe the moon roof dry with a cloth before operating it.

130

1

1-6. Refueling Opening the fuel tank cap

Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle

● Turn the “POWER” switch off and close all the doors and win-

dows.

● Confirm the type of fuel. (→P. 132)

■ Opening the fuel tank cap

STEP 1

STEP 2

STEP 3

Pull up the opener to open the fuel filler door.

Turn the fuel tank cap slowly to open.

Hang the fuel tank cap on the back of the fuel filler door.

131

1-6. Refueling

Closing the fuel tank cap

After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.

■Fuel types

Use unleaded gasoline. (Octane rating 87 [Research Octane Number 91] or higher)

■Gasoline price setting screen

After refueling more than approximately 1.3 gal. (5 L, 1.1 Imp.gal.) L and turning the “POWER” switch to ON mode, the gasoline price setting screen will be automatically displayed on the multi-information display. (→P. 231)

132

1

1-6. Refueling

CAUTION

■When refueling the vehicle

Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel filler door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.

●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury. ●Do not allow anyone that has not discharged static electricity from their

body to come close to an open fuel tank.

●Do not inhale vaporized fuel.

Fuel contains substances that are harmful if inhaled.

●Do not smoke while refueling the vehicle.

Doing so may cause the fuel to ignite and cause a fire.

●Do not return to the vehicle or touch any person or object that is statically

charged. This may cause static electricity to build up, resulting in a possible ignition hazard.

■When refueling

Observe the following precautions to prevent fuel overflowing from the fuel tank: ●Securely insert the fuel nozzle into the fuel filler neck ●Stop filling the tank after the fuel nozzle automatically clicks off ●Do not top off the fuel tank

■When replacing the fuel tank cap

Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.

133

1-6. Refueling

NOTICE

■Refueling

Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle’s painted surface.

134

1-7. Theft deterrent system Immobilizer system

The vehicle’s keys have built-in transponder chips that prevent the hybrid system from starting if a key has not been previously regis- tered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.

The indicator light flashes after the “POWER” switch has been turned off to indicate that the system is operating. The indicator light stops flash- ing after the “POWER” switch has been turned to ACCES- SORY or ON mode to indicate that the system has been can- celed.

■System maintenance

The vehicle has a maintenance-free type immobilizer system.

■Conditions affecting operation

Depending on the surrounding environment and conditions, the immobilizer system may not operate properly. This may prevent the hybrid system from starting. (→P. 72)

135

1-7. Theft deterrent system

■Certifications for the immobilizer system

For vehicles sold in the U.S.A. FCC ID: NI4TMIMB-1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For vehicles sold in Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

NOTICE

■To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guar- anteed.

136

1-7. Theft deterrent system Theft prevention labels (for the U.S.A.)

These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.

137

1-8. Safety information Correct driving posture

Drive with a good posture as follows:

and to

Sit upright and well back in the seat. (→P. 99) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (→P. 99) Adjust the seatback so that the controls are easily oper- able. (→P. 99) Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (→P. 117) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 105) Wear the seat belt correctly. (→P. 109)

138

1-8. Safety information

CAUTION

■While driving

●Do not adjust the position of the driver’s seat.

Doing so could cause the driver to lose control of the vehicle.

●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.

●Do not place anything under the front seats.

Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent, resulting in death or serious injury. The adjustment mechanism may also be damaged.

■Adjusting the seat position

●Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

●Do not put your hands under the seat or near the moving parts to avoid

injury. Fingers or hands may become jammed in the seat mechanism.

139

1-8. Safety information SRS airbags

The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.

SRS front airbags

SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components SRS knee airbag Can help provide driver protection

140

1-8. Safety information

SRS side and curtain shield airbags

SRS side airbags Can help protect the torso of the front seat occupants SRS curtain shield airbags Can help protect primarily the head of occupants in the outer seats

141

1-8. Safety information

SRS airbag system components

Front passenger airbag “AIR BAG ON” and “AIR BAG OFF” indicator lights Side airbags Curtain shield airbags Front passenger occupant classification system (ECU and sensors) Side impact sensors (rear) SRS warning light Driver airbag

Side impact sensors (front) Seat belt pretensioners and force limiters Driver’s seat belt buckle switch Driver’s seat position sensor Driver’s knee airbag Front passenger’s seat belt buckle switch Front impact sensors Airbag sensor assembly

142

1

1-8. Safety information

Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with nontoxic gas to help restrain the motion of the occupants.

■If the SRS airbags deploy (inflate)

●Bruising and slight abrasions may result from contact with a deploying

(inflating) SRS airbag.

●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes. The airbag itself may also be hot.

●The windshield may crack. ●For Safety Connect subscribers, if the SRS airbags deploy or in the event of a severe rear-end collision, the system is designed to send an emer- gency call to the response center, notifying them of the vehicle’s location (without needing to push the “SOS” button) and an agent will attempt to speak with the occupants to ascertain the level of emergency and assis- tance required. If the occupants are unable to communicate, the agent automatically treats the call as an emergency and helps to dispatch the necessary emergency services. (→P. 388)

143

1-8. Safety information

■SRS airbag deployment conditions (SRS front airbags)

●The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher in the following situations: • If the vehicle strikes an object, such as a parked vehicle or sign pole,

which can move or deform on impact

• If the vehicle is involved in an underride collision such as a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck

●Depending on the type of collision, it is possible that only the seat belt

pretensioners will activate.

●The SRS front airbags for the front passenger will not activate if there is no passenger sitting in the front passenger seat. However, the SRS front airbags for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied. (→P. 154)

■SRS airbag deployment conditions (SRS side and curtain shield air-

bags) The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by an approximately 3300 lb. [1500 kg] vehicle collid- ing with the vehicle cabin from a direction perpendicular to the vehicle orien- tation at an approximate speed of 12 - 18 mph [20 - 30 km/h]).

144

1

1-8. Safety information

■Conditions under which the SRS airbags may deploy (inflate), other

than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

●Hitting a curb, edge of pavement or

hard surface

●Falling into or jumping over a deep hole ●Landing hard or falling

■Types of collisions that may not deploy the SRS airbags (SRS front air-

bags) The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, deployment of the SRS front airbags may occur.

●Collision from the side ●Collision from the rear ●Vehicle rollover

145

1-8. Safety information

■Types of collisions that may not deploy the SRS airbags

(SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.

●Collision from the side to the vehicle body other than the passenger com- partment

●Collision from the side at an angle

The SRS side and curtain shield airbags do not generally inflate if the vehi- cle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low-speed side collision.

●Collision from the front ●Collision from the rear ●Vehicle rollover

■When to contact your Toyota dealer

In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. ●Any of the SRS airbags has been inflated.

●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.

146

1-8. Safety information

●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side and cur- tain shield airbags to inflate.

●The pad section of the steering wheel, dashboard near the front passenger air- bag or lower portion of the driver’s side instrument panel is scratched, cracked, or otherwise damaged.

●The surface of the seats with the side airbag is scratched, cracked, or other- wise damaged.

●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked, or other- wise damaged.

147

1-8. Safety information

CAUTION

■SRS airbag precautions

Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts

properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (NHTSA) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching the

pedals comfortably.

• Slightly recline the back of the seat.

Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-

bag toward your chest instead of your head and neck.

The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.

148

1

CAUTION

■SRS airbag precautions

1-8. Safety information

●If the seat belt extender has been con- nected to the front seat belt buckles but the seat belt extender has not also been fastened to the latch plate of the seat belt, the SRS front airbags will judge that the driver and front passen- ger are wearing the seat belt even though the seat belt has not been con- nected. In this case, the SRS front air- bags may not activate correctly in a collision, resulting in death or serious injury in the event of a collision. Be sure to wear the seat belt with the seat belt extender.

●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.

●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat. (→P. 160)

149

●Do not sit on the edge of the seat or

lean against the dashboard.

●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.

●Do not allow the front seat occupants to

hold items on their knees.

●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.

●Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.

1-8. Safety information

CAUTION

■SRS airbag precautions

150

1

CAUTION

■SRS airbag precautions

1-8. Safety information

●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.

●Do not attach anything to areas such as a door, windshield glass, side door glass, front or rear pillar, roof side rail, and assist grip.

●Do not hang coat hangers or hard objects on the coat hooks. All of these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy.

●If a vinyl cover is put on the area where the SRS knee airbags will deploy,

be sure to remove it.

151

1-8. Safety information

CAUTION

■SRS airbag precautions

●Do not use seat accessories which cover the parts where the SRS side airbags inflate as they may interfere with inflation of the airbags. Such accessories may prevent the side airbags from activating correctly, disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury.

●Do not strike or apply significant levels of force to the area of the SRS air-

bag components. Doing so can cause the SRS airbags to malfunction.

●Do not touch any of the component parts immediately after the SRS air-

bags have deployed (inflated) as they may be hot.

●If breathing becomes difficult after the SRS airbags have deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.

●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.

●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the SRS front airbags for the front passenger may not deploy in the event of a collision.

152

1

1-8. Safety information

CAUTION

■Modification and disposal of SRS airbag system components

Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails

●Repairs or modifications of the front fender, front bumper, or side of the

occupant compartment

●Installation of snow plows, winches, etc. to the front grille (bull bars or kan-

garoo bar etc.)

●Modifications to the vehicle’s suspension system ●Installation of electronic devices such as mobile two-way radios and CD

players

●Modifications to your vehicle for a person with a physical disability

153

1-8. Safety information Front passenger occupant classification system

Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.

SRS warning light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light Front passenger’s seat belt reminder light

154

1-8. Safety information

Condition and operation in the front passenger occupant classification system ■ Adult*1

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Front passenger’s seat belt reminder light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger’s seat belt pretensioner

“AIR BAG

ON” Off

Flashing*2

Activated

■ Child*3 or child restraint system*4

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Front passenger’s seat belt reminder light

Front passenger airbag

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger’s seat belt pretensioner

“AIR BAG OFF”*5

Off

Flashing*2
Deactivated

Activated

155

1-8. Safety information

■ Unoccupied

Indicator/

warning light

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Front passenger’s seat belt reminder light

Not illuminated

Off

Front passenger airbag

Deactivated

Devices

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Activated

Front passenger’s seat belt pretensioner

Deactivated

■ There is a malfunction in the system

Indicator/

warning light

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Front passenger’s seat belt reminder light

“AIR BAG

OFF” On Off

Front passenger airbag

Deactivated

Devices

Side airbag on the front passenger seat Curtain shield airbag in the front passen-

ger side

Front passenger’s seat belt pretensioner

Activated

156

1

1-8. Safety information

*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.

*2: In the event the front passenger does not wear a seat belt. *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.

*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 160)

*5: In case the indicator light is not illuminated, consult this manual

on how to install the child restraint system properly. (→P. 165)

157

1-8. Safety information

CAUTION

■Front passenger occupant classification system precautions

Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger’s seat belt plate has not been left inserted

into the buckle before someone sits in the front passenger seat.

●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, and reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the SRS airbags for the passenger may not activate correctly, which could cause death or serious injury in the event of a collision.

●Do not apply a heavy load to the front passenger seat or equipment (e.g.

seatback pocket).

●Do not put weight on the front passenger seat by putting your hands or

feet on the front passenger seat seatback from the rear passenger seat.

●Do not let a rear passenger lift the front passenger seat with their feet or

press on the seatback with their legs.

●Do not put objects under the front passenger seat.

158

1

1-8. Safety information

CAUTION

■Front passenger occupant classification system precautions

●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.

●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.

●When it is unavoidable to install a forward-facing child restraint system on the front passenger seat, install the child restraint system on the front pas- senger seat in the proper order. (→P. 165)

●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.

●Child restraint systems installed on the rear seat should not contact the

front seatbacks.

●Do not use a seat accessory, such as a cushion and seat cover, that cov-

ers the seat cushion surface.

●Do not modify or replace the upholstery of the front seat.

159

1-8. Safety information Child restraint systems

A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.

Points to remember

Studies have shown that installing a child restraint on a rear seat is much safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and is

appropriate to the age and size of the child.

● For installation details, follow the instructions provided with the

child restraint system. General installation instructions are provided in this manual. (→P. 165)

160

1-8. Safety information

Types of child restraints

Child restraint systems are classified into the following 3 types according to the age and size of the child. Rear facing ⎯ Infant seat/convertible seat

Forward facing ⎯ Convertible seat

Booster seat

161

1-8. Safety information

■When installing a child restraint system on the front passenger seat

When you have to use a child restraint system on the front passenger seat, adjust the following: ●The seatback to the most upright posi-

tion

●The seat cushion to the fully rearward

position

■Selecting an appropriate child restraint system

●Use a child restraint system appropriate for the child until the child

becomes large enough to properly wear the vehicle’s seat belt.

●If the child is too large for a child restraint system, sit the child on a rear

seat and use the vehicle’s seat belt. (→P. 109)

CAUTION

■Child restraint precautions

●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.

162

1

1-8. Safety information