, a confirmation message is displayed. If
*:Bluetooth is a registered trademark of Bluetooth SIG. Inc.
317
PRIUS_U_(L/O_0802)
3-5. Using the interior lights Interior lights list
Illuminated entry system: The various lights automatically turn on/ off according to the presence of the electronic key, whether the doors are locked/unlocked, whether the doors are open/closed, and the “POWER” switch mode.
ITY35P001
Front personal lights (→P. 320) Front interior lights (→P. 320) Key slot lights Front door courtesy lights Rear interior lights (→P. 320)
318
PRIUS_U_(L/O_0802)
3-5. Using the interior lights
n To prevent 12 volt battery discharge
If the interior lights and personal lights ON when the door is not fully closed or the interior light switch in “DOOR” position, the lights will go off automati- cally after 20 minutes.
n Customization that can be configured at Toyota dealer
Setting (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 488)
319
PRIUS_U_(L/O_0802)
3-5. Using the interior lights
Interior lights
Front
Rear
“ON” “OFF” “DOOR” The interior lights are turned on/ off by the illuminated entry sys- tem.
“ON” “OFF” “DOOR” The interior lights are turned on/ off by the illuminated entry sys- tem.
Personal light
ON/OFF
320
PRIUS_U_(L/O_0802)
3-5. Using the interior lights
n Customization that can be configured at Toyota dealer. Settings can be changed. (Customizable features →P. 488)
321
PRIUS_U_(L/O_0802)
3-6. Using the storage features List of storage features
Overhead console Auxiliary box Glove box Cup holders Console box Bottle holder
322
PRIUS_U_(L/O_0802)
3-6. Using the storage features
Glove box
Push the button.
n Glove box light
The glove box light turns on when the headlight switch is on.
CAUTION
n While driving
Keep the glove box closed. Injuries may result in the event of an accident or sudden braking.
Console box
Lift the lid while pulling the lever.
323
PRIUS_U_(L/O_0802)
3-6. Using the storage features
CAUTION
n While driving
Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Overhead console
The overhead console is useful for temporarily storing sunglasses and similar small items.
Push the lid.
CAUTION
n Items that should not be left in the overhead console
Do not leave glasses or lighters in the console. If the interior of the vehicle becomes hot, lighters may explode and glasses may warp or become cracked.
n While driving
Do not leave the overhead console open. Items may fall out and cause injury.
324
PRIUS_U_(L/O_0802)
Cup holders
Front
Rear
3-6. Using the storage features
To open, press down and release the front cup holder lid.
To open, press in and release the rear cup holder on the arm- rest.
CAUTION
n Items unsuitable for the cup holder
Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.
n When not in use
Keep the cup holders closed. Injuries may result in the event of an accident or sudden braking.
325
PRIUS_U_(L/O_0802)
3-6. Using the storage features
Bottle holders
326
PRIUS_U_(L/O_0802)
3-6. Using the storage features
Push the button.
Push the lid.
Lift the tray and pull it forward.
327
Auxiliary box
Type A
Type B
Type C
PRIUS_U_(L/O_0802)
3-6. Using the storage features
n Removing the separate tray (type A)
Pull up.
ITY36P011
CAUTION
n While driving
Keep the auxiliary boxes closed. Injuries may result in the event of an acci- dent or sudden braking.
328
PRIUS_U_(L/O_0802)
3-7. Other interior features Sun visors
Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.
ITY37P001
329
PRIUS_U_(L/O_0802)
3-7. Other interior features Vanity mirror
Slide the cover.
ON: The
light the cover
turns on is
when opened.
OFF: Turns the light off.
330
PRIUS_U_(L/O_0802)
3-7. Other interior features Clock
Adjusts the hour Adjusts the minutes.
ITY37P003
n The clock is displayed when
The “POWER” switch is in ACCESSORY or ON mode.
n When the 12 volt battery is disconnected
The time display will automatically be set to 1:00.
n When the instrument panel lights are turned on the brightness of the
time indicator will be reduced.
331
PRIUS_U_(L/O_0802)
3-7. Other interior features Power outlet
The power outlet can be used for 12V accessories that run on less than 10A.
Instrument panel
Rear console box
n The power outlet can be used when
The “POWER” switch is in ACCESSORY or ON mode.
332
PRIUS_U_(L/O_0802)
3-7. Other interior features
NOTICE
n To avoid damaging the power outlet
Close the power outlet lid when not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.
n To prevent the fuse from being blown
Do not use an accessory that uses more than 12V/10A.
n To prevent 12 volt battery discharge
Do not use the power outlet longer than necessary when the engine is not running.
333
PRIUS_U_(L/O_0802)
3-7. Other interior features Armrest
Pull the armrest down for use.
ITY37P006
NOTICE
n To prevent damage to the armrest
Do not place too much strain on the armrest.
334
PRIUS_U_(L/O_0802)
3-7. Other interior features Floor mats
Securely place a mat that matches the size of the space on the car- pet.
Secure the floor mat using the hooks provided.
CAUTION
n When inserting the floor mat
Observe the following precautions. Failure to do so may result in the floor mat slipping and interfering with the movement of the pedals during driving, resulting in an accident. l Make sure the floor mat is properly placed on the vehicle carpet and the
correct side faces upward.
l Do not place floor mats on top of existing mats.
335
PRIUS_U_(L/O_0802)
3-7. Other interior features Luggage compartment features
n Cargo hooks
Cargo hooks are provided for securing loose items.
the
knob
Turn the “UNLOCK” position and open the lid.
to
Hold the lid open by inserting the support rod into the slot.
n Auxiliary box
STEP 1
LOCK
UNLOCK
STEP 2
ITY37P008
LOCK
UNLOCK
ITY37P009
ITY37P010
336
PRIUS_U_(L/O_0802)
3-7. Other interior features
n Luggage cover (If equipped)
STEP 1
Adjust the cover so that “TOP” is facing upwards.
STEP 2
Pull out the luggage cover and secure it to the hook brackets.
ITY37P011
ITY37P012
n Removing the luggage cover
The luggage cover can be removed by following the procedure below.
Lift it up.
T O P
ITY37P013
337
PRIUS_U_(L/O_0802)
Remove the side deck boards and open the auxiliary box.
Adjust the cover so that “TOP” is facing up.
3-7. Other interior features
n Stowing the luggage cover
STEP 1
STEP 2
ITY37P015
CAUTION
n While driving
To avoid injury, always return the cargo hooks to their positions when they are not in use.
338
PRIUS_U_(L/O_0802)
3-7. Other interior features Garage door opener
The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, and other devices.
The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.
Programming the HomeLink® (for U.S.A. owners)
The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.
Buttons Indicator
n Programming the HomeLink®
STEP 1
ITY37P017
Point the remote control for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® control but- tons.
Keep the indicator light on the HomeLink® in view while pro- gramming.
339
PRIUS_U_(L/O_0802)
3-7. Other interior features
STEP 2
STEP 3
ITY37P018
ITY37P019
Press and hold down one of the buttons on the HomeLink® and the button on the transmitter. When the indicator light on the HomeLink® changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
Test the operation of HomeLink® by pressing newly programmed button.
the the
the
hold
If programming a garage door
opener, check to see if the garage
door opens and closes. If the
garage door does not operate,
see if your garage transmitter is
of the Rolling Code type. Press
and
programmed
HomeLink® button. The garage
door has the rolling code feature
if
the
HomeLink®) flashes rapidly for 2
seconds and then remains lit. If
your transmitter is the Rolling
Code type, proceed to the head-
ing “Programming a rolling code
system”.
light (on
indicator
the
STEP 4
Repeat the steps above to program another device for each of the remaining HomeLink® buttons.
340
PRIUS_U_(L/O_0802)
3-7. Other interior features
n Programming a Rolling Code system (for U.S.A. owners)
If your device is Rolling Code equipped, follow the steps under the heading “Programming the HomeLink®” before proceeding with the steps listed below.
STEP 1
STEP 2
STEP 3
STEP 4
Locate the training button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the training button. Press the training button. Press and release the vehicle’s programmed HomeLink® but- ton twice. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® transceiver and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.
n Programming an entry gate (for U.S.A. owners)/Programming
all devices in the Canadian market
STEP 1
STEP 2
STEP 3
STEP 4
Place your transmitter 1 to 3 in. (25 to 75 mm) away from the surface of the HomeLink®. Keep the indicator light on the HomeLink® in view while program- ming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the device’s remote control button for two seconds each until step 4 is complete. When the indicator light on the HomeLink® compatible trans- ceiver start to flashing rapidly, release the buttons.
341
PRIUS_U_(L/O_0802)
3-7. Other interior features
STEP 5
STEP 6
Test the operation of the HomeLink® by pressing the newly programmed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for each of the remaining HomeLink® buttons.
n Programming other devices
To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.
n Reprogramming a button
The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Basic program- ming” instructions.
Operating the HomeLink®
Press the appropriate HomeLink® button. The HomeLink® indicator light on the HomeLink® transceiver should turn on.
The HomeLink® continues to send a signal for up to 20 seconds as long as the button is pressed.
Erasing the entire HomeLink® memory (all three programs)
Press and hold down the 2 out- side buttons for 20 seconds until the indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.
ITY37P020
342
PRIUS_U_(L/O_0802)
3-7. Other interior features
n Before programming
Install a new battery in the transmitter.
l The battery side of the transmitter must be pointed away from the
HomeLink®.
n Certification for the garage door opener
This device complies with Part 15 of the FCC Rules and with RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party respon- sible for compliance could void the user’s authority to operate the device.
CAUTION
n When programming a garage door or other remote control device
The garage door may operate, so ensure people and objects are out of dan- ger to prevent potential harm.
n Conforming to federal safety standards
Do not use the HomeLink® Compatible Transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an obstruction object. A door or device without these features increases the risk of death or serious injury.
343
PRIUS_U_(L/O_0802)
3-7. Other interior features
344
PRIUS_U_(L/O_0802)
4-1. Maintenance and care Cleaning and protecting the vehicle’s exterior
Perform the following to protect the vehicle and maintain it in prime condition.
l Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a cham- ois.
l For hard-to-remove marks, use car wash soap and rinse thor-
oughly with water.
l Wipe away any water. l Wax the vehicle when the waterproof coating deteriorates.
If water does not bead on a clean surface, apply wax when the vehicle body is cool.
n Automatic car washes
l Fold the mirrors back before washing the vehicle. l Brushes used in automatic car washes may scratch the vehicle surface
and harm your vehicle’s paint.
n High pressure automatic car washes
Do not allow the nozzles of the car wash to come within close proximity of the windows. Before entering an automatic car wash, check that the fuel filler door is closed.
n Aluminum wheels
Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.
n Bumpers and side moldings
Do not scrub with abrasive cleaners.
346
PRIUS_U_(L/O_0802)
4-1. Maintenance and care
n To prevent paint deterioration and corrosion on the body
l Wash the vehicle immediately in the following cases:
• After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface • If you see dead insects or insect droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,
iron powder or chemical substances
• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzine and gasoline are spilled on the paint surface If the paint is chipped or scratched, have it repaired immediately.
CAUTION
n Caution about the exhaust pipe
Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.
NOTICE
n To protect your vehicle’s painted surfaces
Do not use organic cleaners such as benzine or gasoline.
n Cleaning the exterior lights
l Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
l Do not apply wax on the surface of the lights. Wax may cause damage to
the lenses.
347
PRIUS_U_(L/O_0802)
4-1. Maintenance and care Cleaning and protecting the vehicle’s interior
The following procedures will help protect your vehicle’s interior and keep it in top condition: n Protecting the vehicle interior
Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
n Cleaning the leather areas
l Remove dirt and dust using a vacuum cleaner. l Wipe any excess dirt and dust with a soft cloth dampened with
diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.
l Wring out any excess water from the cloth and thoroughly
wipe off all remaining traces of detergent.
l Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in shaded and ventilated area.
n Synthetic leather areas
l Remove loose dirt using a vacuum cleaner. l Apply a mild soap solution to the synthetic leather using a
sponge or soft cloth.
l Allow the solution to soak in for a few minutes. Remove the
dirt and wipe off the solution with a clean, damp cloth.
348
PRIUS_U_(L/O_0802)
4-1. Maintenance and care
n Cleaning the inside of the rear window
Do not use glass cleaner to clean the rear window, as this may cause dam- age to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.
n Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
n Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained by keeping the carpet as dry as possible.
n Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.
CAUTION
n Water in the vehicle
l Be careful not to splash or spill liquid on the floor. l Do not get any of the SRS components or wiring in the vehicle interior wet.
(→P. 90) Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.
349
PRIUS_U_(L/O_0802)
4-1. Maintenance and care
NOTICE
n Cleaning detergents
Do not use the following types of detergent, as they may discolor the vehicle interior or cause streaks or damage to painted surfaces. l Non-seat portions: Organic substances such as benzine or gasoline, alka-
line or acidic solutions, dye, or bleach.
l Seats: Acidic solutions, such as thinner, benzine, or alcohol.
n Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of leather surfaces. l Remove any dust or dirt on leather surfaces immediately. l Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
l Do not place items made of vinyl, plastic, or that contain wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.
n Water on the floor
Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.
n Cleaning the inside of the rear window
Be careful not to scratch or damage the heater wires or antenna.
350
PRIUS_U_(L/O_0802)
4-2. Maintenance Maintenance requirements
To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. n General maintenance
Should be performed on a daily basis. This can be done by your- self or by a Toyota dealer. n Scheduled maintenance
Should be performed at specified intervals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
n Do-it-yourself maintenance
You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals are recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.
n Repair and replacement
It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
351
PRIUS_U_(L/O_0802)
4-2. Maintenance
n Allow inspection and repairs to be performed by a Toyota dealer
l Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
l Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.
CAUTION
n Hazardous materials
l Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
l Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.
l 12 volt battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 375)
l Used engine oil contains chemicals that have been shown to cause cancer in laboratory animals. Avoid prolonged and repeated contact. Always pro- tect your skin by washing thoroughly with soap and water.
352
PRIUS_U_(L/O_0802)
4-2. Maintenance General maintenance
Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.
Engine compartment
Items
Check points
Brake fluid Engine/power control unit coolant Engine oil Exhaust system
Radiator/condenser/hoses
Washer fluid
Luggage compartment
(→P. 373) (→P. 371) (→P. 365)
• At the correct level? • At the correct level? • At the correct level? • No fumes or strange sounds? • Not blocked with foreign matter? (→P. 373) (→P. 378)
• At the correct level?
Items
Check points
12 volt battery
• Maintenance-free
(→P. 375)
353
PRIUS_U_(L/O_0802)
4-2. Maintenance
Vehicle interior
Items
Check points
Accelerator pedal
Automatic transmission “Park” mechanism
Brake pedal
Brakes
Head restraints Indicators/buzzers Lights
Parking brake
Seat belts
Seats
Steering wheel
• Moves smoothly (without uneven pedal effort or catching)? • Can the vehicle be hold securely on an incline with the shift lever in “P”? • Moves smoothly? • Does it have appropriate clearance and correct amount of free play? • Pulls to one side when applied? • Loss of brake effectiveness? • Spongy feeling brake pedal? • Pedal almost touches floor? • Move smoothly and lock securely? • Function properly? • Do all the lights come on? • Moves smoothly? • Can hold the vehicle securely on an incline? • Does the seat belt system operate smoothly? • Are the belts undamaged? • Do the seat controls operate properly? • Moves smoothly? • Has correct free play? • No strange noises?
354
PRIUS_U_(L/O_0802)
4-2. Maintenance
Vehicle exterior
Items
Check points
Doors Engine hood Fluid leaks
Tire
• Operate smoothly? • The lock system works properly? • Is there any leakage after parking? • Inflation pressure is correct? • Tire surfaces not worn or damaged? • Tires rotated according to the mainte- nance schedule? • Wheel nuts are not loose?
CAUTION
n If the hybrid system is running
Turn off the hybrid system and ensure that there is adequate ventilation before performing maintenance checks.
355
PRIUS_U_(L/O_0802)
4-2. Maintenance Emission inspection and maintenance (I/M) programs
Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. n If the malfunction indicator lamp comes on
The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.
n Your vehicle may not pass the I/M test:
l When the 12 volt battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.
l When the fuel tank cap is loose
The malfunction indicator lamp comes on as a temporary mal- function and your vehicle may not pass the I/M test.
n When the malfunction indicator lamp goes off after several
driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.
n If your vehicle does not pass the I/M test
Contact your Toyota dealer to prepare the vehicle for re-testing.
356
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance Do-it-yourself service precautions
If you perform maintenance yourself, be sure to follow the correct procedure given in these sections.
Items
Parts and tools
12 volt battery condition
(→P. 375)
Brake fluid level
(→P. 373)
Engine/power control unit coolant (→P. 371) level
• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. For the U.S.A.: “Toyota Super Long Life Cool- ant” is pre-mixed with 50% cool- ant and 50% deionized water. For Canada: “Toyota Super Long Life Cool- ant” is pre-mixed with 55% cool- ant and 45% deionized water. • Funnel (used only for adding cool- ant)
357
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Items
Engine oil level
(→P. 365)
Fuses
(→P. 398)
Radiator and condenser
(→P. 373)
Tire inflation pressure (→P. 388)
Washer fluid
(→P. 378)
Parts and tools
• “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel, funnel (used only for adding engine oil) • Fuse with same amperage rating as original
⎯
• Tire pressure gauge • Compressed air source • Water washer fluid containing anti- freeze (for winter use) • Funnel
358
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury. n When working on the engine compartment:
l Keep hands, clothing, and tools away from the moving fan and engine
drive belt.
l Be careful not to touch the engine, inverter, radiator, exhaust manifold, etc. right after driving as they may be hot. Oil and other fluids may also be hot. l Do not leave anything that may burn easily, such as paper or rags, in the
engine compartment.
l Do not smoke, cause sparks or expose an open flame to fuel or the 12 volt
battery. Fuel and 12 volt battery fumes are flammable.
l Be extremely cautious when working on the 12 volt battery. It contains poi-
sonous and corrosive sulfuric acid.
l Never touch, disassemble, remove or replace the high voltage parts, cables and their connectors. It can cause severe burns or electric shock that may result in death or serious injury.
l When the hybrid system is operating with the “READY” light on, the engine may suddenly start in some cases. When you inspect the engine compart- ment, be sure to turn off the hybrid system.
n When working near the electric cooling fan or radiator grille
Be sure the “POWER” switch is OFF. With the “POWER” switch in ON mode, the electric cooling fan may automat- ically start to run if the air conditioning is on and/or the coolant temperature is high. (→P. 373)
n Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in the eyes.
359
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
NOTICE
n If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment.
360
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance Hood
Release the lock from the inside of the vehicle to open the hood.
STEP 1
STEP 2
STEP 3
STEP 3
Pull the hood lock release lever.
The hood will pop up slightly.
Lift the hood catch and lift the hood.
Hold the hood open by insert- ing the supporting rod into the slot.
ITY43P001
ITY43P002
ITY43P003
CAUTION
n Pre-driving check
Check that the hood is fully closed and locked. If the hood is not locked properly it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
361
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance Positioning a floor jack
When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Front
Rear
362
PRIUS_U_(L/O_0802)
ITY43P005
4-3. Do-it-yourself maintenance
CAUTION
n When raising your vehicle
Make sure to observe the following to reduce the possibility of death or seri- ous injury.
l Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
l Do not use the floor jack that was supplied with your vehicle. l Do not put any part of your body or get underneath the vehicle supported
only by the floor jack. Always use automotive jack stands or a solid, level, surface.
l Do not start the hybrid system while the vehicle is supported by the floor
jack.
l Stop the vehicle on level firm ground, firmly set the parking brake and push
the “P” position switch.
l Make sure to set the jack properly at the jack point.
Raising the vehicle with an improperly positioned jack will damage the vehicle and may cause the vehicle to fall off the jack.
l Do not raise the vehicle while someone is in the vehicle. l When raising the vehicle, do not place any objects on top of or underneath
the jack.
363
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance Engine compartment
Washer fluid tank
Inverter coolant reservoir
(→P. 378)
Brake fluid reservoir
(→P. 373)
Engine oil filler cap
(→P. 367)
Engine coolant reservoir
(→P. 371)
(→P. 371) (→P. 398) (→P. 373) (→P. 373)
Fuse box Radiator Condenser Electric cooling fans Engine oil level dipstick
(→P. 365)
n 12 volt battery
→P. 375
364
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Engine compartment cover
n Removing the cover
Front
n Installing the clips
Push up center portion Insert Press
Engine oil
With the engine at operating temperature and turned off, check the oil
level on the dipstick.
n Checking the engine oil
STEP 1
Park the vehicle on level ground. After turning off the hybrid system, wait a few minutes for the oil to drain back into the bottom of the engine.
365
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
STEP 2
Hold a rag under the end and pull the dipstick out.
STEP 3
STEP 4
STEP 5
STEP 6
Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully. Low Full
ITY43P010
366
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Make sure to check the oil type and prepare the items needed before adding oil.
Oil grade Oil quantity (Low → Full)
ILSAC multigrade engine oil
1.6 qt. (1.5 L, 1.3 Imp. qt.)
Items
Clean funnel
STEP 1
STEP 2
STEP 3
Remove the oil filler cap. Add engine oil slowly, checking the dipstick. Install the filler cap, turning it clockwise until you hear a click.
367
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Recommended viscosity
SAE 5W-30 is the best choice for good fuel economy, and good starting in cold weather.
*: If SAE 5W-30 oil is not avail- able, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change.
Outside temperature
n How to read oil container labels
The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use.
368
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
n Engine oil consumption
l The amount of engine oil consumed depends on the oil viscosity, the
quality of the oil and the way the vehicle is driven.
l More oil is consumed under driving conditions such as high speeds, fre-
quent acceleration and deceleration.
l A new engine consumes more oil. l When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accu- rately.
l Oil consumption: Max. 1.1 qt./600 miles, 0.9 lmp. qt./600 miles (1.0 L per 1000 km). If the vehicle consumes more than this amount, contact your Toyota dealer.
n Resetting the engine oil maintenance data (U.S.A. only)
Perform the following steps:
STEP 1
Turn the “POWER” switch to OFF mode with the trip meter A shown. Turn the “POWER” switch to ON mode with the trip meter reset but- ton (→P. 144) held down. Keep pressing the button for longer than 5 seconds after the “POWER” switch is in ON mode.
STEP 2
STEP 3
When the trip meter A indicates “000000” and the light goes off, the system reset is completed.
369
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
CAUTION
n Used engine oil
l Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
l Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
l Do not leave used engine oil within the reach of children.
NOTICE
n To prevent serious engine damage Check the oil level on regular basis.
n When replacing the engine oil
l Be careful not to spill engine oil on the vehicle components. l Avoid overfilling, or the engine could be damaged. l Check the oil level on the dipstick every time you refill the vehicle. l Be sure the engine oil filler cap is properly retightened.
370
PRIUS_U_(L/O_0802)
4-3. Do-it-yourself maintenance
Engine/power control unit coolant
The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir when the engine is cold.
Engine coolant reservoir
FULL LOW
FULL LOW
ITY43P012
Reservoir cap FULL LOW If the level is on or below the “LOW” line, add coolant up to the “FULL” line.
Power control unit coolant reservoir
LOW
LOW
FULL
ITY43P013
PRIUS_U_(L/O_0802)