431
Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals
The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile wire- less phones. Those guidelines are consistent with the safety stan- dards previously set by the following U.S. and international standards bodies. ● ANSI (American National Standards Institute) C95.1 [1992] ● NCRP (National Council on Radiation Protection and Measure-
ment) Report 86 [1986]
● ICNIRP (International Commission on Non-Ionizing Radiation
Protection) [1996]
Those standards were based on comprehensive and periodic eval- uations of the relevant scientific literature. Over 120 scientists, engi- neers, and physicians from universities, and government health agencies and industries reviewed the available body of research to develop the ANSI Standard (C95.1). The design of Safety Connect complies with the FCC guidelines in addition to those standards.
■Certification for Safety Connect
FCC ID: O6Y-CDMRF101
FCC ID: XOECDMRF101B
FCC ID: N7NGTM2
FCC WARNING:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65. This equipment should be installed
and operated keeping the radiator at least 20cm or more away from person’s
body (excluding extremities: hands, wrists, feet and ankles).
LC200_OM_OM60M88U_(U)
432
5-4. Using the other interior features
LC200_OM_OM60M88U_(U)
Maintenance and care
433
6-1. Maintenance and care
Cleaning and protecting
the vehicle exterior.......... 434
Cleaning and protecting
the vehicle interior........... 437
6-2. Maintenance
Maintenance
requirements................... 440
General maintenance........ 443
Emission inspection and
maintenance (I/M)
programs......................... 446
6-3. Do-it-yourself maintenance
Do-it-yourself service
precautions ..................... 447
Hood ................................. 449
Engine compartment......... 450
Tires .................................. 463
Tire inflation pressure ....... 472
Wheels .............................. 475
Air conditioning filter.......... 477
Electronic key battery........ 479
Checking and replacing
fuses ............................... 481
Headlight aim .................... 485
Light bulbs......................... 487
LC200_OM_OM60M88U_(U)
434
6-1. Maintenance and care
Cleaning and protecting the vehicle exterior
Perform the following to protect the vehicle and maintain it in prime condition:
● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
● Wash the vehicle body using a sponge or soft cloth, such as a
chamois.
● For hard-to-remove marks, use car wash soap and rinse thoroughly
with water.
● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates.
If water does not bead on a clean surface, apply wax when the vehicle body is cool.
■Automatic car washes
●Fold the mirrors back before washing the vehicle. Start washing from the
front of the vehicle. Make sure to extend the mirrors before driving.
●Brushes used in automatic car washes may scratch the vehicle surface and
harm your vehicle’s paint.
●Rear spoiler (if equipped) may not be washable in some automatic car
washes. There may also be an increased risk of damage to vehicle.
■High pressure car washes
●Do not allow the nozzles of the car wash to come within close proximity of
the windows.
●Before using the car wash, check that the fuel filler door on your vehicle is
closed properly. ■Aluminum wheels
●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical clean- ers. Use the same mild detergent and wax as used on the paint.
●Do not use detergent on the wheels when they are hot, for example after
driving for long distance in the hot weather.
●Wash detergent from the wheels immediately after use.
■Bumpers and side moldings
Do not scrub with abrasive cleaners.
LC200_OM_OM60M88U_(U)
6-1. Maintenance and care
435
■Notes for a smart key system (if equipped)
●If the door handle becomes wet while the electronic key is within the effec- tive range, the door may lock and unlock repeatedly. Place the key in a posi- tion 2 m (6 ft.) or more separate from the vehicle while the vehicle is being washed. (Take care to ensure that the key is not stolen.)
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on the multi-information dis- play and a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
WARNING
■When washing the vehicle
Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire.
■When cleaning the windshield (vehicles with rain-sensing windshield
wiper) Set the wiper switch to off. If the wiper switch is in “AUTO”, the wip- ers may operate unexpectedly in the fol- lowing situations, and may result in hands being caught or other serious inju- ries and cause damage to the wiper blades.
OFF
AUTO
●When the upper part of the windshield where the raindrop sensor is
located is touched by hand
●When a wet rag or similar is held close to the raindrop sensor ●If something bumps against the windshield ●If you directly touch the raindrop sensor body or if something bumps into
the raindrop sensor
■Precautions regarding the exhaust pipe
Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.
■Precautions regarding the Blind Spot Monitor (if equipped)
If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, consult your Toyota dealer.
LC200_OM_OM60M88U_(U)
436
6-1. Maintenance and care
NOTICE
■To prevent paint deterioration and corrosion on the body and compo-
nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:
• After driving near the sea coast • After driving on salted roads • If coal tar or tree sap is present on the paint surface • If you see dead insects, insect droppings or bird droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,
iron powder or chemical substances
• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface
●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place
with low humidity when storing wheels.
■Cleaning the exterior lights
●Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
●Do not apply wax on the surfaces of the lights.
Wax may cause damage to the lenses.
■When using an automatic car wash (vehicles with rain-sensing wind-
shield wiper) Turn off the wiper switch. If the wiper switch is in “AUTO”, the wipers may operate and the wiper blades may be damaged.
■When using a high pressure car wash
Do not bring the nozzle tip close to boots (rubber or resin manufactured cover), connectors or the following parts. The parts may be damaged if they come into contact with high-pressure water. • Traction related parts • Steering parts • Suspension parts • Brake parts
LC200_OM_OM60M88U_(U)
6-1. Maintenance and care
437
Cleaning and protecting the vehicle interior
The following procedures will help protect your vehicle’s interior and keep it in top condition:
Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
If dirt cannot be removed, wipe it off with neutral detergent diluted to approximately 1%.
Cleaning the leather areas ● Remove dirt and dust using a vacuum cleaner. ● Wipe any excess dirt and dust with a soft cloth dampened with
diluted detergent. Use a diluted water solution of approximately 5% neutral wool detergent.
● Wring out any excess water from the cloth and thoroughly wipe off
all remaining traces of detergent.
● Wipe the surface with a dry, soft cloth to remove any remaining
moisture. Allow the leather to dry in a shaded ventilated area.
Cleaning the synthetic leather areas ● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather using a sponge
or soft cloth.
● Allow the solution to soak in for a few minutes. Remove the dirt and
wipe off the solution with a clean, damp cloth.
LC200_OM_OM60M88U_(U)
438
6-1. Maintenance and care
■Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
■Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. The excellent results are obtained when keeping the carpet as dry as possible.
■Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.
WARNING
■Water in the vehicle
●Do not splash or spill liquid in the vehicle.
Doing so may cause electrical components etc. to malfunction or catch fire.
●Do not get any of the SRS components or wiring in the vehicle interior wet.
(P. 40) An electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.
■Cleaning the interior (especially instrument panel)
Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver’s view and leading to an accident, resulting in death or serious injury.
NOTICE
■Cleaning detergents
●Do not use the following types of detergent, as they may discolor the vehi-
cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline,
alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-
hol
●Do not use polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
LC200_OM_OM60M88U_(U)
6-1. Maintenance and care
439
NOTICE
■Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of leather surfaces: ●Remove any dust or dirt from leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
●Do not place items made of vinyl, plastic, or containing wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.
■When cleaning the inside of the windshield (vehicles with Toyota
Safety Sense P) Do not allow glass cleaner to contact the lens. Also, do not touch the lens. (P. 230)
■Water on the floor
Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components such as the audio system above or under the floor of the vehicle. Water may also cause the body to rust. ■Cleaning the inside of the rear quarter windows and rear window
●Do not use glass cleaner to clean the rear quarter windows and rear win- dow, as this may cause damage to the rear window defogger heater wires or antenna. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires or antenna.
●Be careful not to scratch or damage the heater wires or antenna.
LC200_OM_OM60M88U_(U)
440
6-2. Maintenance
Maintenance requirements
To ensure safe and economical driving, day-to-day care and reg- ular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following main- tenance:
General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.
Scheduled maintenance Scheduled maintenance should be performed at specified intervals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
Do-it-yourself maintenance You can perform some maintenance procedures by yourself. Please be aware that do-it-yourself maintenance may affect warranty coverage.
The use of Toyota repair manuals is recommended. For details about warranty coverage, see the “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supplement”.
LC200_OM_OM60M88U_(U)
6-2. Maintenance
441
■Repair and replacement
It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
■Resetting the message indicating maintenance is required
After the required maintenance is performed according to the maintenance schedule, please reset the message. To reset the message, follow the procedures described below:
Press
or
of the meter control switches, select
of the meter control switches, select “Scheduled
or
Press Maintenance” and then press Select the “Yes” and press A message is displayed on the multi-information display.
■Allow inspection and repairs to be performed by a Toyota dealer
●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operation of all systems on your vehicle.
●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.
LC200_OM_OM60M88U_(U)
442
6-2. Maintenance
WARNING
■If your vehicle is not properly maintained
Improper maintenance could result in serious damage to the vehicle and possible serious injury or death.
■Handling of the battery
●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.
●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (P. 459)
LC200_OM_OM60M88U_(U)
6-2. Maintenance
443
General maintenance
Listed below are the general maintenance items that should be performed at the intervals specified in the “Warranty and Service Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.
Engine compartment
Items
Battery Brake fluid
Engine coolant
Engine oil
Exhaust system
Power steering fluid
Radiator/condenser
Washer fluid
Check points
(P. 459) Check the connections. Is the brake fluid at the correct level? (P. 456) Is the engine coolant at the correct level?
(P. 455) Is the engine oil at the correct level? (P. 452) There should not be any fumes or strange sounds. Is the power steering fluid at the correct level? (P. 458) The radiator and condenser should be free from foreign objects. (P. 456) (P. 462) Is there sufficient washer fluid?
LC200_OM_OM60M88U_(U)
444
6-2. Maintenance
Vehicle interior
Items
Accelerator pedal
Check points
• The accelerator pedal should move smoothly
(without uneven pedal effort or catching).
Automatic transmission “Park” mechanism
• When parked on a slope and the shift lever is
in P, is the vehicle securely stopped?
ance from the floor?
• Does the brake pedal move smoothly? • Does the brake pedal have appropriate clear- (P. 558) the correct (P. 558) • The vehicle should not pull to one side when
the brake pedal have
amount of free play?
• Does
the brakes are applied.
• The brakes should work effectively. • The brake pedal should not feel spongy. • The brake pedal should not get too close to
the floor when the brakes are applied.
• Do the head restraints move smoothly and
lock securely?
• Do the indicators and buzzers function prop-
erly?
• Do all the lights come on? • Are the headlights aimed correctly? (P. 485) • Does the parking brake lever move smoothly? • When parked on a slope and the parking
brake is on, is the vehicle securely stopped?
• Do the seat belts operate smoothly? • The seat belts should not be damaged. • Do the seat controls operate properly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the correct
amount of free play?
• There should not be any strange sounds com-
ing from the steering wheel.
Brake pedal
Brakes
Head restraints
Indicators/buzzers
Lights
Parking brake
Seat belts
Seats
Steering wheel
LC200_OM_OM60M88U_(U)
6-2. Maintenance
445
Check points
• Do the doors operate smoothly? • Does the engine hood lock system work prop-
erly?
• There should not be any signs of fluid leakage
after the vehicle has been parked.
• Is the tire inflation pressure correct? • The tires should not be damaged or exces-
sively worn.
• Have the tires been rotated according to the
maintenance schedule?
• The wheel nuts should not be loose. • The wiper blades should not show any signs of cracking, splitting, wear, contamination or deformation.
• The wiper blades should clear the windshield/
rear window without streaking or skipping.
Vehicle exterior
Items
Doors
Engine hood
Fluid leaks
Tires
Windshield wipers/rear window wiper
WARNING
■If the engine is running
Turn off the engine and ensure that there is adequate ventilation before per- forming maintenance checks.
LC200_OM_OM60M88U_(U)
446
6-2. Maintenance
Emission inspection and maintenance (I/M) programs
Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system monitors the operation of the emission control system.
If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.
Your vehicle may not pass the I/M test in the following situations: ● When the battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.
● When the fuel tank cap is loose
The malfunction indicator lamp comes on indicating a temporary malfunction and your vehicle may not pass the I/M test.
When the malfunction indicator lamp still remains on after sev- eral driving trips The error code in the OBD system will not be cleared unless the vehi- cle is driven 40 or more times.
If your vehicle does not pass the I/M test Contact your Toyota dealer to prepare the vehicle for re-testing.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
447
Do-it-yourself service precautions
If you perform maintenance yourself, be sure to follow the cor- rect procedures as given in these sections.
Items
Battery condition (P. 459)
Brake fluid level (P. 456)
Engine coolant level (P. 455)
Engine oil level (P. 452)
Fuses (P. 481) Headlight aim (P. 485)
Light bulbs (P. 487)
Power steering fluid level (P. 458) Radiator and con- denser (P. 456) Tire inflation pressure (P. 472)
Parts and tools • Baking soda
• Warm water • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long- life hybrid organic acid technology. “Toyota Super Long Life Coolant” is pre-mixed with 50 % coolant and 50 % deionized water.
• Funnel (used only for adding coolant) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel • Funnel (used only for adding engine oil)
• Fuse with same amperage rating as original
• Phillips-head screwdriver
• Bulb with same number and wattage rating as origi-
nal
• Flathead screwdriver
• Phillips-head screwdriver • Wrench • Automatic transmission fluid DEXRON® II or III • Rag or paper towel • Funnel (used only for adding power steering fluid)
• Tire pressure gauge
• Compressed air source
LC200_OM_OM60M88U_(U)
448
6-3. Do-it-yourself maintenance
Items
Washer fluid (P. 462)
WARNING
Parts and tools
• Water or washer fluid containing antifreeze (for win-
ter use)
• Funnel (used only for adding water or washer fluid)
The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions: ■When working on the engine compartment
●Keep hands, clothing and tools away from the moving fan and engine
drive belt.
●Be careful not to touch the engine, radiator, exhaust manifold, etc. right
after driving as they may be hot. Oil and other fluids may also be hot.
●Do not leave anything that may burn easily, such as paper or rags, in the
engine compartment.
●Do not smoke, cause sparks or expose an open flame to fuel or the bat-
tery. Fuel and battery fumes are flammable.
●Be extremely cautious when working on the battery. It contains poisonous
and corrosive sulfuric acid.
■When working near the electric cooling fans or radiator grille
Be sure the engine switch is off. With the engine switch in IGNITION ON mode, the electric cooling fans may automatically start to run if the air condi- tioning is on and/or the coolant temperature is high. (P. 456)
■When working on or under the vehicle
Do not get under the vehicle with just the jack supporting it. Always use automotive jack stands or other solid supports.
■Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in your eyes.
NOTICE
■If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
449
Hood
Release the lock from the inside of the vehicle to open the hood.
Pull the hood lock release lever. The hood will pop up slightly.
Lift the hood catch and lift the hood.
WARNING
■Pre-driving check
Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
LC200_OM_OM60M88U_(U)
450
6-3. Do-it-yourself maintenance
Engine compartment
Power steering fluid reservoir (P. 458)
Engine oil level dipstick
(P. 452)
Engine coolant reservoir
(P. 455) Cooling fans (P. 456) Engine oil filler cap (P. 453)
10
11
Brake fluid reservoir
(P. 456) Fuse box (P. 481) Washer fluid tank (P. 462) Battery (P. 459) (P. 456) Condenser Radiator (P. 456)
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
451
Engine compartment cover ■ Removing the engine compartment cover
■ Installing the clips
Push up center portion Insert Press
NOTICE
■After installing an engine compartment cover
Make sure the cover is securely installed in its original position.
LC200_OM_OM60M88U_(U)
452
6-3. Do-it-yourself maintenance
Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil
Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine. Holding a rag under the end, pull the dipstick out.
Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level.
Low Normal Excessive The shape of the dipstick may differ depending on the type of vehicle or engine.
Wipe the dipstick and reinsert it fully.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
453
■ Adding engine oil
If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Make sure to check the oil type and prepare the items needed before adding oil.
Engine oil selection Oil quantity (Low Full) 1.6 qt. (1.5 L, 1.3 Imp.qt.) Items
Clean funnel
P. 554
Remove the oil filler cap by turning it counterclockwise. Add engine oil slowly, checking the dipstick. Install the oil filler cap by turning it clockwise.
■Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals. ●When the engine is new, for example directly after purchasing the vehicle or
after replacing the engine
●If low quality oil or oil of an inappropriate viscosity is used ●When driving at high engine speeds or with a heavy load, when towing, or
when driving while accelerating or decelerating frequently
●When leaving the engine idling for a long time, or when driving frequently
through heavy traffic
LC200_OM_OM60M88U_(U)
454
6-3. Do-it-yourself maintenance
■After changing the engine oil
The engine oil maintenance data should be reset. Perform the following pro- cedures:
Press
or
of the meter control switches, select
of the meter control switches, select “Oil Maintenance”
or
Press and then press Select the “Yes” and press A message is displayed on the multi-information display.
WARNING
■Used engine oil
●Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
●Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
●Do not leave used engine oil within the reach of children.
NOTICE
■To prevent serious engine damage Check the oil level on regular basis.
■When replacing the engine oil
●Be careful not to spill engine oil on the vehicle components. ●Avoid overfilling, or the engine could be damaged. ●Check the oil level on the dipstick every time you refill the vehicle. ●Be sure the engine oil filler cap is properly tightened.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
455
Engine coolant The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold.
Reservoir cap “F” “L” If the level is on or below the “L” line, add coolant up to the “F” line.
■Coolant selection
Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50 % coolant and 50 % deionized water. (Minimum temperature: -31F [-35C]) For more details about engine coolant, contact your Toyota dealer.
■If the coolant level drops within a short time of replenishing
Visually check the radiator, hoses, engine coolant reservoir caps, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system.
WARNING
■When the engine is hot
Do not remove the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns.
NOTICE
■When adding coolant
Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.
■If you spill coolant
Be sure to wash it off with water to prevent it from damage to parts or paint.
LC200_OM_OM60M88U_(U)
456
6-3. Do-it-yourself maintenance
Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts is extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer.
WARNING
■When the engine is hot
Do not touch the radiator or condenser as they may be hot and cause seri- ous injuries, such as burns.
Brake fluid ■ Checking fluid level
The brake fluid level should be between the “MAX” and “MIN” lines on the tank.
“MAX” line “MIN” line
■ Adding fluid
Make sure to check the fluid type and prepare the necessary item.
Fluid type Items ■ Refilling brake fluid
FMVSS No.116 DOT 3 or SAE J1703 brake fluid Clean funnel
Turn the engine switch off. Depress the brake pedal more than 40 times. Remove the reservoir cap by hand. Add brake fluid up to the “MAX” line. If you do not follow the procedure above, the reservoir may overflow.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
457
■Brake fluid can absorb moisture from the air
Excess moisture in the fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid.
WARNING
■When filling the reservoir
Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.
NOTICE
■If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.
LC200_OM_OM60M88U_(U)
458
6-3. Do-it-yourself maintenance
Power steering fluid ■ Fluid level
The fluid level should be within the appropriate range.
Full (when hot) Add fluid (when hot) Full (when cold) Add fluid (when cold)
Hot: The vehicles has been driven around 50 mph (80 km/h) for
20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 140F - 175F [60C - 80C]). Cold: The engine has not been run for about 5 hours. (Room temperature, 50F - 85F [10C - 30C]).
■ Checking the fluid level
Make sure to check the fluid type and prepare the necessary items.
Fluid type Items
Automatic transmission fluid DEXRON® II or III Rag or paper, clean funnel (only for adding fluid)
Clean all dirt off the reservoir. Remove the cap by turning it counterclockwise. Wipe the dipstick clean. Reinstall the cap and remove it again. Check the fluid level.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
459
WARNING
■When checking the reservoir
Take care as the reservoir may be hot.
NOTICE
■When adding fluid
Avoid overfilling, or the power steering may be damaged.
■After replacing the reservoir cap
Check the steering box case, vane pump and hose connections for leaks or damage.
Battery Check the battery as follows. ■ Battery exterior
Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Terminals Hold-down clamp
LC200_OM_OM60M88U_(U)
460
6-3. Do-it-yourself maintenance
■Before recharging
When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, observe the following before recharging: ●If recharging with the battery installed on the vehicle, be sure to disconnect
the ground cable.
●Make sure the power switch on the charger is off when connecting and dis-
connecting the charger cables to the battery.
■After recharging/reconnecting the battery
The engine may not start. Follow the procedure below to initialize the system.
Shift the shift lever to P Open and close any of the doors. Restart the engine.
●Unlocking the doors using the smart key system may not be possible imme- diately after reconnecting the battery. If this happens, use the wireless remote control or the mechanical key to lock/unlock the doors.
●Start the engine with the engine switch in ACCESSORY mode. The engine may not start with the engine switch turned off. However, the engine will operate normally from the second attempt.
●The engine switch mode is recorded by the vehicle. If the battery is recon- nected, the vehicle will return the engine switch mode to the status it was in before the battery was disconnected. Make sure to turn off the engine before disconnect the battery. Take extra care when connecting the battery if the engine switch mode prior to discharge is unknown.
If the engine will not start even after multiple attempts at both methods, con- tact your Toyota dealer.
WARNING
■Chemicals in the battery
Batteries contain poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near battery: ●Do not cause sparks by touching the battery terminals with tools. ●Do not smoke or light a match near the battery. ●Avoid contact with eyes, skin and clothes. ●Never inhale or swallow electrolyte. ●Wear protective safety glasses when working near the battery. ●Keep children away from the battery.
■Where to safely charge the battery
Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
461
WARNING
■How to recharge the battery
Only perform a slow charge (5A or less). The battery may explode if charged at a quicker rate.
■Emergency measures regarding electrolyte
●If electrolyte gets in your eyes
Flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
●If electrolyte gets on your skin
Wash the affected area thoroughly. If you feel pain or burning, get medical attention immediately.
●If electrolyte gets on your clothes
It can soak through clothing on to your skin. Immediately take off the cloth- ing and follow the procedure above if necessary.
●If you accidentally swallow electrolyte
Drink a large quantity of water or milk. Get emergency medical attention immediately.
NOTICE
■When recharging the battery
Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
LC200_OM_OM60M88U_(U)
462
6-3. Do-it-yourself maintenance
Washer fluid If any washer does not work or the warning message appears on the multi-information the washer tank may be empty. Add washer fluid.
display,
WARNING
■When adding washer fluid
Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and may catch fire if spilled on the engine etc.
NOTICE
■Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces.
■Diluting washer fluid
Dilute washer fluid with water as necessary. Refer to the freezing temperatures listed on the label of the washer fluid bot- tle.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
463
Tires
Replace or rotate tires in accordance with maintenance sched- ules and treadwear.
Checking tires Check if the treadwear indicators are showing on the tires. Also check the tires for uneven wear, such as excessive wear on one side of the tread. Check the spare tire condition and pressure if not rotated.
New tread Worn tread Treadwear indicator The location of treadwear indicators is shown by the “TWI” or “ mark, etc., molded into the sidewall of each tire. Replace the tires if the treadwear indicators are showing on a tire.
”
Tire rotation Rotate the shown.
tires
in
the order
To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the same interval as tire inspection. Do not fail to initialize the tire pressure warning system after tire rotation.
Front
LC200_OM_OM60M88U_(U)
464
6-3. Do-it-yourself maintenance
Tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire infla- tion pressure before serious problems arise. ● If the tire pressure drops below a predetermined level, the driver is
warned by a screen display and a warning light. (P. 512)
● The tire pressure detected by the tire pressure warning sys- tem can be displayed on the multi-information display.
◆ Installing tire pressure warning valves and transmitters
When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer.
◆ Initializing the tire pressure warning system ■ The tire pressure warning system must be initialized in the fol-
lowing circumstances: ● When rotating the tires. When the tire pressure warning system is initialized, the current tire inflation pressure is set as the pressure benchmark.
LC200_OM_OM60M88U_(U)
■ How to initialize the tire pressure warning system
6-3. Do-it-yourself maintenance
465
Park the vehicle in safe place and turn the engine switch to OFF. Initialization cannot be performed while the vehicle is moved. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. (P. 558) Make sure to adjust the tire pressure to the specified cold tire infla- tion pressure level. The tire pressure warning system will operate based on this pressure level. Turn the engine switch to IGNITION ON mode. Press and hold the tire pres- sure warning reset switch until the tire pressure warn- ing light blinks slowly 3 times.
“--” will be displayed for inflation pressure of each tire on the multi- information display while the tire pressure warning system deter- mines the position on the multi-information display. When position of each tire is determined, the inflation pressure of each tire will be displayed on the multi-information display. Drive the vehicle at approximately 25mph (40 km/h) or more for approximately 10 minutes. When initialization is complete, the inflation pressure of each tire will be displayed on the multi-information display. Initialization will take longer than approximately 10 minutes if the vehicle is stopped for a long time, such as at traffic signals.
◆ Registering ID codes
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.
LC200_OM_OM60M88U_(U)
466
6-3. Do-it-yourself maintenance
■When to replace your vehicle’s tires
Tires should be replaced if: ●The treadwear indicators are showing on a tire. ●You have tire damage such as cuts, splits, cracks deep enough to
expose the fabric, and bulges indicating internal damage
●A tire goes flat repeatedly or cannot be properly repaired due to the size
or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
■Replacing tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not reg-
istered, the tire pressure warning system will not work properly. After driv-
ing for about 20 minutes, the tire pressure warning light blinks for 1
minute and stays on to indicate a system malfunction.
■Tire life
Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.
■Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.
■Maximum load of tire
Check that the number given by dividing the maximum load by 1.10 of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire. (P. 563)
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
467
■Tire types
●Summer tires
Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When install- ing snow tires, be sure to replace all four tires.
●All season tires
All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions as well as for use year-round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance com- pared with summer tires in highway driving.
●Snow tires
For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restrictions. Snow tires should be installed on all wheels. (P. 369)
■When rotating the tires
Make sure that the engine switch is off. If the tires are rotated while the engine switch is in IGNITION ON mode, the tire position information will not be updated. If this accidentally occurs, either turn the engine switch to off and then to IGNITION ON mode, or initialize the system after checking that the tire pressure is properly adjusted.
LC200_OM_OM60M88U_(U)
468
6-3. Do-it-yourself maintenance
■If the tread on snow tires wears down below 0.16 in. (4 mm)
The effectiveness of the tires as snow tires is lost.
■Initializing the tire pressure warning system
initialize the system with the tire inflation pressure adjusted to the speci- fied level.
■Situations in which the tire pressure warning system may not oper-
ate properly ●In the following cases, the tire pressure warning system may not operate
properly. • If non-genuine Toyota wheels are used. • A tire has been replaced with a tire that is not an OE (Original Equip-
ment) tire.
• A tire has been replaced with a tire that is not of the specified size. • Tire chains etc. are equipped. • An auxiliary-supported run-flat tire is equipped. • If a window tint that affects the radio wave signals is installed. • If there is a lot of snow or ice on the vehicle, particularly around the
wheels or wheel housings.
• If the spare tire is in a location subject to poor radio wave signal
• If a large metallic object which can interfere with signal reception is
• If tires not equipped with the tire pressure warning valves and trans-
reception.
put near the spare tire.
mitters are used.
• If the ID code on the tire pressure warning valves and transmitters is
not registered in the tire pressure warning computer.
●Performance may be affected in the following situations.
• Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise
• When carrying a portable radio, cellular phone, cordless phone or
other wireless communication device
●When the vehicle is parked, the time taken for the warning to start or go
off could be extended.
●When tire inflation pressure declines rapidly for example when a tire has
burst, the warning may not function.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance
469
■The initialization operation
●Make sure to carry out initialization after adjusting the tire inflation pres- sure. Also, make sure the tires are cold before carrying out initialization or tire inflation pressure adjustment.
●If you have accidentally turned the engine switch off during initialization, it is not necessary to press the reset switch again as initialization will restart automatically when the engine switch has been turned to IGNI- TION ON mode for the next time.
●If you accidentally press the reset switch when initialization is not neces- sary, adjust the tire inflation pressure to the specified level when the tires are cold, and conduct initialization again.
●While the position of each tire is being determined and the inflation pres- sures are not being displayed on the multi-information display, if the inflation pressure of a tire drops, the tire pressure warning light will come on.
■Warning performance of the tire pressure warning system
The warning of the tire pressure warning system will change in accor- dance with the conditions under which it was initialized. For this reason, the system may give a warning even if the tire pressure does not reach a low enough level, or if the pressure is higher than the pressure that was adjusted to when the system was initialized.
■When initialization of the tire pressure warning system has failed
Initialization may take longer to complete if the vehicle is driven on an
unpaved road. When performing initialization, drive on a paved road if
possible. Depending on the driving environment and condition of the tires,
initialization will be completed in approximately 10 minutes. If initialization
is not complete after driving approximately 10 minutes, continue driving
for a while.
If the inflation of each tire is not displayed after driving for approximately 1
hour, perform the following procedure.
●Park the vehicle in a safe place for approximately 20 minutes. Then
drive straight (with occasional left and right turns) at approximately
25 mph (40 km/h) or more for approximately 10 to 20 minutes.
However, in the following situations, the tire inflation pressure will not be recorder and the system will not operate properly. Perform initialization. ●When operating the tire pressure warning reset switch, the tire pressure
warning light does not blink 3 times.
●After performing initialization, the tire pressure warning light blinks for 1
minute then stays on after driving for about 20 minutes.
If the inflation pressure of each tire is still not displayed, have the vehicle inspected by your Toyota dealer.
LC200_OM_OM60M88U_(U)
470
6-3. Do-it-yourself maintenance
■Tire pressure warning system certification
WARNING
■Tire pressure warning system operation
The tire pressure warning system may not provide warning immediately if a tire bursts or if sudden air leakage occurs.
■When inspecting or replacing tires
Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury. ●Do not mix tires of different makes, models or tread patterns.
Also, do not mix tires of remarkably different treadwear.
●Do not use tire sizes other than those recommended by Toyota. ●Do not mix differently constructed tires (radial, bias-belted or bias-ply
tires).
●Do not mix summer, all season and snow tires. ●Do not use tires that have been used on another vehicle.
Do not use tires if you do not know how they were used previously.
■When initializing the tire pressure warning system
Do not operate the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.
LC200_OM_OM60M88U_(U)
6-3. Do-it-yourself maintenance