2010 Toyota Highlander Owners Manual

523

5-2. Steps to take in an emergency

Taking out the spare tire

STEP 1

Open the center deck board and remove the cover.

STEP 2

Remove the cover.

If it is difficult to remove the cover, you can use the key.

STEP 3

Attach the adapter socket (for removing a spare tire) on the spare tire clamp bolt.

524

STEP 4

STEP 5

STEP 6

5-2. Steps to take in an emergency

Assemble the jack handle and tighten the screw.

Connect the jack handle and the adapter socket. Turn the jack handle.

The tire will be lowered com- pletely to the ground.

Pull out the spare tire and stand it against the bumper.

STEP 7

Remove the holding bracket.

525

5-2. Steps to take in an emergency

Replacing a flat tire

STEP 1
STEP 1

Chock the tires.

Flat tire

Front

Rear

Left- hand side

Right- hand side

Left- hand side

Right- hand side

Wheel chock positions Behind the rear right- hand side tire Behind the rear left- hand side tire In front of the front right-hand side tire In front of the front left-hand side tire

STEP 2

Slightly loosen the wheel nuts (one turn).

526

STEP 3

STEP 4

STEP 5

5-2. Steps to take in an emergency

Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point.

Raise the vehicle until the tire is slightly raised off the ground.

Remove all the wheel nuts and the tire.

When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.

527

5-2. Steps to take in an emergency

Installing the tire

STEP 1

Remove any dirt or foreign mat- ter from the wheel contact sur- face.

If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.

STEP 2

Install the tire and loosely tighten each wheel nut by hand by approximately the same amount.

Vehicles without compact spare tire

Disc wheel

Turn the nut washers until they come into contact with the disc wheel.

Washer

Vehicles with compact spare tire

Tapered portion

Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.

Disc wheel sheet

528

5-2. Steps to take in an emergency

STEP 3

Lower the vehicle.

STEP 4

Firmly tighten each nut two or three times in the order shown in the illustration.

Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)

Stowing the flat tire, jack and all tools

STEP 1

from

Remove the center wheel orna- ment by pushing the reverse side. Put the flat tire on the ground with the outer side facing up and install the holding bracket.

Be careful not to lose the wheel ornament.

STEP 2

STEP 3

Turn the spare tire clamp bolt clockwise with a jack handle and adapter socket until you hear a click. Stow the jack and all tools.

529

5-2. Steps to take in an emergency

■The compact spare tire

●The compact spare tire is identified by the label “TEMPORARY USE

ONLY” on the tire sidewall. Use the compact spare tire temporarily only in an emergency.

●Make sure to check the tire inflation pressure of the compact spare

tire. (→P. 562)

■When using the compact spare tire

As the compact spare tire is not equipped with the tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be warned. Also, if you replace the compact spare tire after the tire pressure warning light comes on, the light remains on.

■If you have a flat front tire on a road covered with snow or ice (vehi-

cles with compact spare tire) Install the spare tire on the rear of the vehicle. Perform the following steps and fit tire chains to the front tires. STEP 1

Replace a rear tire with the compact spare tire. Replace the flat front tire with the tire removed from the rear of the vehicle. Fit tire chains to the front tires.

STEP 2

STEP 3

■After completing the tire change

The tire pressure warning system must be reset. (→P. 455)

530

5-2. Steps to take in an emergency

CAUTION

■Using the tire jack

Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. ●Do not use the tire jack for any purpose other than replacing tires or

installing and removing tire chains.

●Only use the tire jack that comes with this vehicle for replacing a flat

tire. Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.

●Always check that the tire jack is securely set to the jack point. ●Do not put any part of your body under the vehicle supported by a jack. ●Do not start or run the engine while your vehicle is supported by the

jack.

●Do not raise the vehicle while someone is in it. ●When raising the vehicle, do not put an object on or under the jack. ●Do not raise the vehicle to a height greater than that required to

replace the tire.

●Use a jack stand if it is necessary to get under the vehicle. Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle will be injured.

531

5-2. Steps to take in an emergency

CAUTION

■Replacing a flat tire

Observe the following precautions to reduce the risk of death or serious injury. ●Never use oil or grease on the wheel bolts or wheel nuts.

Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing a serious accident. Remove any oil or grease from the wheel bolts or wheel nuts.

●Have the wheel nuts tightened with a torque wrench to 76 ft•lbf (103

N•m, 10.5 kgf•m) as soon as possible after changing wheels. Failure to follow these precautions could cause the nuts to loosen and the wheel may fall off, which could lead to an accident causing death or serious injury.

■When using the compact spare tire

●Remember that your compact spare tire is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle.

●Do not use two compact spare tires simultaneously. ●Replace the compact spare tire with a standard tire as soon as possi-

ble.

●Avoid sudden acceleration, deceleration and braking, as well as sharp

cornering.

■Speed limit when using the compact spare tire

Do not drive at speeds in excess of 50 mph (80 km/h) when a compact spare tire is installed on the vehicle. The compact spare tire is not designed for driving at high speeds. Failing to observe this precaution may lead to an accident causing death or seri- ous injury.

532

5-2. Steps to take in an emergency

CAUTION

■When the compact spare tire is attached

The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ●ABS & Brake assist ●Enhanced VSC ●TRAC ●Cruise control system ●Navigation system (if equipped) Also, not only can be following system not be utilized fully, it may actually negatively effect the drive-train components: (4WD models) ●4WD system

533

5-2. Steps to take in an emergency

NOTICE

■Do not drive the vehicle with a flat tire.

Do not continue driving with a flat tire. Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.

■Be careful when driving over bumps with the compact spare tire

installed on the vehicle. The vehicle becomes lower when driving with the compact spare tire compared to when driving with standard tires. Be careful when driving over uneven road surfaces.

■Driving with tire chains and the compact spare tire

Do not fit tire chains to the compact spare tire. Tire chains may damage the vehicle body and adversely affect driving performance.

■When replacing the tires

When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. ■To avoid damaging the tire pressure warning valves and transmit-

ters Do not use liquid sealants on flat tires.

■When stowing the flat tire

●Ensure that there is no object caught between the tire and the vehicle

underbody.

●Tighten the spare tire clamp bolt to hold the spare wheel carrier by the

hook securely.

534

5-2. Steps to take in an emergency If the engine will not start

If the engine still does not start after following the correct starting procedure (→P. 173, 177) or releasing the steering lock (→P. 175, 178), confirm the following points. ■ The engine will not start even when the starter motor oper-

ates normally. One of the following may be the cause of the problem. ● There may not be sufficient fuel in the vehicle’s tank.

Refuel the vehicle.

● The engine may be flooded.

Try to restart the engine once more following correct starting procedures. (→P. 173, 177)

● There may be a malfunction in the engine immobilizer system.

(→P. 115)

■ The starter motor turns over slowly, the interior lights and headlights are dim, or the horn does not sound or sounds at a low volume. One of the following may be the cause of the problem. ● The battery may be discharged. (→P. 541) ● The battery terminal connections may be loose or corroded.

■ The starter motor does not turn over (vehicles with smart

key system). The engine starting system may be malfunctioning due to an electrical problem such as an open circuit or a blown fuse. How- ever, an interim measure is available to start the engine. (→P. 536)

535

5-2. Steps to take in an emergency

■ The starter motor does not turn over, the interior lights and

headlights do not turn on, or the horn does not sound. One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (→P. 541) ● There may be a malfunction in the steering lock system (vehi-

cles with smart key system). Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.

Emergency start function (vehicles with smart key system)

When the engine does not start, the following steps can be used as an interim measure to start the engine if the “ENGINE START STOP” switch is functioning normally. Set the parking brake. STEP 1
Shift the shift lever to P. Set the “ENGINE START STOP” switch to ACCESSORY mode. Push and hold the “ENGINE START STOP” switch about 15
seconds while depressing the brake pedal firmly.

STEP 2

STEP 3

STEP 4

Even if the engine can be started using the above steps, the system may be malfunctioning. Have the vehicle checked by your Toyota dealer.

536

5-2. Steps to take in an emergency If the shift lever cannot be shifted from P

If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted. STEP 1

Set the parking brake. Vehicles without smart key system: Turn the engine switch to the “ACC” position. Vehicles with smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY mode. Depress the brake pedal.

STEP 2

STEP 3

STEP 4

STEP 5

Pry the cover up with a flat- head screwdriver or equiva- lent.

Press the shift lock override button.

The shift lever can be shifted while the button is pressed.

537

5-2. Steps to take in an emergency If you lose your keys/wireless remote control transmitter

■ Keys

New genuine keys can be made by your Toyota dealer. For vehicles with the smart key system, bring the other key and the key number stamped on the key number plate. For vehicles without the smart key system, bring a master key and the key number stamped on the key number plate.

■ Wireless remote control transmitter (vehicles without smart

key system) New genuine wireless remote control transmitters can be pur- chased and programmed by your Toyota dealer. If a wireless remote control transmitter has been lost, bring the other wireless remote control transmitter when going to pick up the new trans- mitter.

538

5-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with smart key system)

If communication between the electronic key and vehicle is inter- rupted (→P. 38) or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote con- trol cannot be used. In such cases, the doors can be opened or the engine can be started by following the procedure below.

Locking and unlocking the doors, and mechanical key linked functions

Using the mechanical key (→P. 31) in order to perform the following operations:

Locks all doors Unlocks all doors Turning the key rearward unlocks the driver’s door. Turning the key once again unlocks the other doors.

Changing “ENGINE START STOP” switch modes and starting the engine

STEP 1

Shift the shift lever to P and apply the brakes.

STEP 2

to

key

Touch the Toyota emblem side of the electronic the “ENGINE START STOP” switch. If any of the doors is opened and closed while the key is being touched to the switch, an alarm will sound to indicate that the start function cannot detect the elec- tronic key.

539

5-2. Steps to take in an emergency

STEP 3

To change “ENGINE START STOP” switch modes: Within 5
seconds of the buzzer sounding, release the brake pedal and press the “ENGINE START STOP” switch. Modes can be changed each time the switch is pressed. (→P. 174) To start the engine: Press the “ENGINE START STOP” switch within 5 seconds after the buzzer sounds, keeping the brake pedal depressed.

In the event that the “ENGINE START STOP” switch still cannot be operated, contact your Toyota dealer.

■Stopping the engine

Shift the shift lever to P and press the “ENGINE START STOP” switch as you normally do when stopping the engine.

■Replacing the electronic key battery

As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery depletes. (→P. 473)

540

5-2. Steps to take in an emergency If the battery is discharged

The following procedures may be used to start the engine if the vehi- cle's battery is discharged. You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. STEP 1

Connect the jumper cables. 2.7 L 4-cylinder (1AR-FE) engine

541

5-2. Steps to take in an emergency

3.5 L V6 (2GR-FE) engine

Positive (+) battery terminal on your vehicle Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicle as shown in the illustration.

STEP 2

STEP 3

Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5
minutes to recharge the battery of your vehicle. Vehicles with smart key system: Open and close any of the doors with the “ENGINE START STOP” switch OFF.

542

5-2. Steps to take in an emergency

STEP 4

STEP 5

Vehicles without smart key system: Maintain the engine speed of the second vehicle, and turn the engine switch to the “ON” position, then start the vehi- cle's engine. Vehicles with smart key system: Maintain the engine speed of the second vehicle, and turn the “ENGINE START STOP” switch to IGNITION ON mode, then start the vehicle's engine. Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected.

Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.

■Starting the engine when the battery is discharged

The engine cannot be started by push-starting.

■To prevent battery discharge

●Turn off the headlights and the audio system while the engine is turned

off.

●Turn off any unnecessary electrical components when the vehicle is run- ning at a low speed for an extended period, such as in heavy traffic, etc.

■When the battery is removed or discharge

●The power back door must be initialized (→P. 75) ●The tire inflation pressure warning system must be initialized. (→P. 455)

543

5-2. Steps to take in an emergency

CAUTION

■Avoiding battery fires or explosions

Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. ●Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.

●Do not allow the jumper cables to come into contact with the “+” and “-” ter-

minals.

●Do not smoke, use matches, cigarette lighters or allow open flame near

the battery.

■Battery precautions

The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following pre- cautions when handling the battery. ●When working with the battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.

●Do not lean over the battery. ●In the event that battery fluid comes into contact with the skin or eyes, immediately wash the affected area with water and seek medical attention. Place a wet sponge or cloth over the affected area until medical attention can be received.

●Always wash your hands after handling the battery support, terminals, and

other battery-related parts.

●Do not allow children near the battery.

NOTICE

■When handling jumper cables

Be careful that the jumper cables do not become tangled in the cooling fan or any of the belts when connecting or disconnecting them.

544

5-2. Steps to take in an emergency If your vehicle overheats

If your engine overheats: STEP 1

Stop the vehicle in a safe place and turn off the air condi- tioning system. Check to see if steam is coming out from under the hood. If you see steam:

STEP 2

Stop the engine. Carefully lift the hood after the steam subsides and then restart the engine.

If you do not see steam:

Leave the engine running and carefully lift the hood.

STEP 3

STEP 4

Remove the engine compartment cover. (→P. 439) Check to see if the cooling fan is operating. If the fan is operating:

Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine.

If the fan is not operating:

Stop the engine and call your Toyota dealer.

STEP 5

After the engine has cooled down sufficiently, check the engine coolant level and inspect the radiator core (radi- ator) for any leaks.

Engine coolant reservoir Radiator

545

5-2. Steps to take in an emergency

STEP 6

Add engine coolant if neces- sary.

Water can be used in an emer- gency is unavailable. (→P. 558)

if engine coolant

Have the vehicle checked at the nearest Toyota dealer as soon as possible.

■Overheating

If you observe the following, your vehicle may be overheating. ●The engine coolant temperature gauge enters the red zone or a loss of

power is experienced.

●Steam is coming from under the hood.

CAUTION

■To prevent an accident or injury when inspecting under the hood of

your vehicle ●If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, caus- ing serious injury such as burns.

●Keep hands and clothing away from the fan and other belts while the

engine is running.

●Do not loosen the coolant reservoir cap while the engine and radiator are

hot. Serious injury, such as burns, may result from hot coolant and steam released under pressure.

546

5-2. Steps to take in an emergency

NOTICE

■When adding engine coolant

Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.

547

5-2. Steps to take in an emergency If the vehicle becomes stuck

Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. STEP 1

Stop the engine. Set the parking brake and put the shift lever in P. Remove the mud, snow, or sand from around the stuck tire. Place wood, stones or some other material to help provide traction under the tires. Restart the engine. Shift the shift lever to the D or R position and carefully apply the accelerator to free the vehicle. Turn off TRAC and/or Enhanced VSC if these functions are ham- pering your attempts to free the vehicle. (→P. 219)

STEP 2

STEP 3

STEP 4

STEP 5

CAUTION

■When attempting to free a stuck vehicle

If you choose to rock the vehicle back and forth to free it, make sure the sur- rounding area is clear, to avoid striking other vehicles, objects or persons. The vehicle may also lunge forward or lunge back suddenly as it becomes free. Use extreme caution.

■When shifting the shift lever

Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

548

5-2. Steps to take in an emergency

NOTICE

■To avoid damaging the transmission and other components

●Avoid spinning the wheels and do not rev the engine. ●If the vehicle remains stuck after trying these procedures, the vehicle may

require towing to be freed.

549

5-2. Steps to take in an emergency

550

6-1. Specifications Maintenance data (fuel, oil level, etc.)

Dimensions and weights

Overall length Overall width

Overall height

Wheelbase

Front tread

Rear tread

2WD models

4WD models

Vehicle capacity weight (Occupant + luggage)

188.4 in. (4785 mm) 75.2 in. (1910 mm) Without roof rails 68.1 in. (1730 mm) With roof rails 69.3 in. (1760 mm)

109.8 in. (2790 mm) 64.0 in. (1625 mm) 64.2 in. (1630 mm)*1
64.2 in. (1630 mm) 64.8 in. (1645 mm)*1
64.0 in. (1625 mm) 64.6 in. (1640 mm)*1

1200 lb. (544 kg)

Towing capacity (Trailer weight + cargo)

2.7 L 4-cylin- der (1AR-FE) engine 3.5 L V6 (2GR-FE) engine

1500 lb. (680 kg)*2
3500 lb. (1500 kg)*3

2000 lb. (900 kg)*2
5000 lb. (2000 kg)*3

*1: GVM condition *2: Without towing package *3: With towing package

552

6-1. Specifications

Vehicle identification

■ Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

This number is stamped under the right-hand front seat.

This number is also stamped on the top left of the instrument panel.

■ Certification Label

This number is also on the Certi- fication Label on the driver’s side center pillar.

553

6-1. Specifications

■ Engine number The engine number is stamped on the engine block as shown.

2.7 L 4-cylinder (1AR-FE) engine

3.5 L V6 (2GR-FE) engine

554

6-1. Specifications

Engine

Model

Type

Bore and stroke

Displacement Drive belt tension

Fuel

Fuel type Octane rating Fuel tank capacity (Reference)

1AR-FE 4-cylinder in line, 4-cycle, gasoline 3.54 × 4.13 in. (90.0 × 105.0 mm) 163.0 cu.in. (2672 cm3) Automatic adjustment

2GR-FE 6-cylinder V type, 4-cycle, gasoline 3.70 × 3.27 in. (94.0 × 83.0 mm) 210.9 cu.in. (3456 cm3)

Unleaded gasoline only 87 (Research Octane Number 91) or higher

19.2 gal. (72.5 L, 15.9 Imp. gal.)

555

6-1. Specifications

Lubrication system

Oil capacity Drain and refill (Refer- ence)

Without filter

With filter

Oil grade

2.7 L 4-cylinder (1AR-FE) engine 4.2 qt. (4.0 L, 3.5 Imp. qt.) 3.5 L V6 (2GR-FE) engine 6.0 qt. (5.7 L, 5.0 Imp. qt.)

2.7 L 4-cylinder (1AR-FE) engine 4.7 qt. (4.4 L, 3.9 Imp. qt.) 3.5 L V6 (2GR-FE) engine 6.4 qt. (6.1 L, 5.4 Imp. qt.) ILSAC multi-grade engine oil

556

Recommended oil viscosity (2.7 L 4-cylinder (1AR-FE) engine)

6-1. Specifications

Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and vis- cosity shown below.

Outside temperature

Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and vis- cosity shown below.

Vehicles without towing package

Recommended oil viscosity (3.5 L V6 (2GR- FE) engine)

Outside temperature

Vehicles with towing package

Outside temperature

557

6-1. Specifications

Oil viscosity ● The 5W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

● The 30 in 5W-30 indicates the oil viscosity when the oil is at its oper- ating temperature. An oil with a higher viscosity may be better suited if the vehicle is operated at high speeds, or under extreme load con- ditions.

Cooling system

Capacity (Reference)

2.7 L 4-cylin- der (1AR-FE) engine

3.5 L V6 (2GR-FE) engine

Without rear air conditioning system 7.3 qt. (6.9 L, 6.1 Imp. qt.) 8.0 qt. (7.6 L, 6.7 Imp. qt.)* With rear air conditioning system 9.6 qt. (9.1 L, 8.0 Imp. qt.) 10.4 qt. (9.8 L, 8.6 Imp. qt.)* Without rear air conditioning system 9.3 qt. (8.8 L, 7.7 Imp. qt.) 10.0 qt. (9.5 L, 8.4 Imp. qt.)* With rear air conditioning system 11.6 qt. (11.0 L, 9.7 Imp. qt.) 12.4 qt. (11.7 L, 10.3 Imp. qt.)*

Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.

Coolant type

*: With towing package

558

6-1. Specifications

Ignition system

Spark plug Make Gap

2.7 L 4-cylinder (1AR-FE) engine DENSO, SK16HR11
3.5 L V6 (2GR-FE) engine DENSO FK20HR11

0.043 in. (1.1 mm)

NOTICE

■Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine.

Electrical system

Battery

Open voltage* at 68°F (20°C):

Charging rates

12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (*: Voltage is checked 20 minutes after the engine and all the lights are turned off) 5 A max.

559

6-1. Specifications

Rear differential (4WD models)

Oil capacity Oil type

Recommended oil viscosity

Automatic transaxle

Fluid capacity*

1.0 qt. (0.9 L, 0.8 Imp. qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

2.7 L 4-cylinder (1AR-FE) engine 6.9 qt. (6.5 L, 5.7 Imp. qt.) 3.5 L V6 (2GR-FE) engine 2WD models: 9.3 qt. (8.8 L, 7.7 Imp. qt.) 4WD models: 9.5 qt. (9.0 L, 7.9 Imp. qt.)

Fluid type *: The fluid capacity is the quantity of reference. If replacement is nec-

Toyota Genuine ATF WS

essary, contact your Toyota dealer.

NOTICE

■Automatic transmission fluid type

Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmis- sion of your vehicle.

560

6-1. Specifications

Transfer (4WD models)

Oil capacity Oil type

Recommended oil viscosity

Brakes

1.0 qt. (0.9 L, 0.8 Imp. qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

Pedal clearance*1
Pedal free play Brake pad wear limit Parking brake lining wear limit Parking brake pedal travel*2
Fluid type *1: Minimum pedal clearance when depressed with a force of 110 lbf (490 N,

3.3 in. (84.4 mm) Min. 0.08 ⎯ 0.12 in. (2 ⎯ 3 mm) 0.04 in. (1.0 mm) 0.04 in. (1.0 mm) 8 ⎯ 10 clicks SAE J1703 or FMVSS No. 116 DOT 3

50 kgf) while the engine is running

*2: Parking brake pedal travel when depressed with a force of 66 lbf (294 N, 30

kgf)

Steering

Free play

Less than 1.2 in. (30 mm)

561

6-1. Specifications

Tires and wheels

Type A

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

P245/65R17 105S Driving under normal conditions Front: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Spare: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indi- cated on the tire sidewall. 17 × 7 1/2 J 76 ft•lbf (103 N•m, 10.5 kgf•m)

562

6-1. Specifications

Type B

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

P245/55R19 103S Driving under normal conditions Front: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Spare: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indi- cated on the tire sidewall. When towing trailer Add 6 psi (40 kPa, 0.4 kgf/cm2 or bar) to the rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 19 × 7 1/2 J 76 ft•lbf (103 N•m, 10.5 kgf•m)

563

6-1. Specifications

Type C

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

P245/65R17 105S, T165/90D18 107M (spare) Driving under normal conditions Front: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.

Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 17 × 7 1/2 J, 18 × 4T (spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

564

6-1. Specifications

Type D

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

P245/55R19 103S, T165/90D18 107M (spare) Driving under normal conditions Front: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 5 psi (30 kPa, 0.3 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. When towing trailer Add 6 psi (40 kPa, 0.4 kgf/cm2 or bar) to the rear tires. Never exceed the maxi- mum cold tire inflation pressure indicated on the tire sidewall.

Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 19 × 7 1/2 J, 18 × 4T (spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

565

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

Type

Headlights Front turn signal lights Parking/front side marker lights Front fog lights* Rear turn signal lights Back-up lights Stop/tail and rear side marker lights License plate lights Outer foot lights* Vanity lights Personal/interior lights (front) Personal/interior lights (center)* Interior light Door courtesy lights

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

⎯

60/55

21
55
21
16

21/5

Exterior

Interior

A: H11 halogen bulbs C: HB2 halogen bulbs *:

If equipped

B: Wedge base bulbs (amber) D: Wedge base bulbs (clear)

566

6-1. Specifications Fuel information

Your vehicle must use only unleaded gasoline. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.

■Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

■If your engine knocks

●Consult your Toyota dealer. ●You may occasionally notice light knocking for a short time while acceler-

ating or driving uphill. This is normal and there is no need for concern.

■Gasoline quality

In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

■Gasoline quality standards

●Automotive manufacturers in the US, Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.

●The WWFC consists of four categories that are based on required emis-

sion levels. In the US, category 4 has been adopted.

●The WWFC improves air quality by lowering emissions in vehicle fleets,

and customer satisfaction through better performance.

567

6-1. Specifications

■Toyota recommends the use of gasoline containing detergent additives ●Toyota recommends the use of gasoline that contains detergent additives

to avoid build-up of engine deposits.

●All gasoline sold in the US contains detergent additives to clean and/or

keep clean intake systems.

■Toyota recommends the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

■Toyota does not recommend blended gasoline

●Toyota allows the use of oxygenate blended gasoline where the oxygen-

ate content is up to 10% ethanol or 15% MTBE.

●If you use gasohol in your Toyota, be sure that it has an octane rating no

lower than 87.

●Toyota does not recommend the use of gasoline containing methanol.

■Toyota does not recommend gasoline containing MMT

Some gasoline contains octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

568

6-1. Specifications

NOTICE

■Notice on fuel quality

●Do not use improper fuels. If improper fuels are used the engine will be

damaged.

●Do not use leaded gasoline.

Leaded gasoline will cause the three-way catalytic converter to lose its effectiveness and the emission control system to function improperly.

●Do not use gasohol other than that stated here.

Other gasohol may cause fuel system damage or vehicle performance problems.

■Fuel-related poor driveability

If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

■When refueling with gasohol

Take care not to spill gasohol. It can damage your vehicle's paint.

569

6-1. Specifications Tire information

Typical tire symbols Full-size spare tire

Compact spare tire

Tire size DOT and Tire Identification Number (TIN) Uniform tire quality grading For details, see “Uniform tire quality grading” that follows. Location of treadwear indicators

(→P. 573) (→P. 572)

(→P. 453)

570

6-1. Specifications

Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube main- tains the air pressure. Load limit at maximum cold tire inflation pressure Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. Summer tire or all season tire (→P. 458) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. “TEMPORARY USE ONLY” (→P. 530) A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded into its sidewall. This tire is designed for temporary emergency use only.

(→P. 458) (→P. 562)

571

6-1. Specifications

Typical DOT and tire identification number (TIN)

Identification Number

DOT symbol* Tire (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional type code (3 or 4 letters) Manufacturing week Manufacturing year *: The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.

tire

572

Tire size

■ Typical tire size information

■ Tire dimensions

6-1. Specifications

The illustration indicates typical tire size.

Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol (alphabet with one letter)

Section width Tire height Wheel diameter

573

6-1. Specifications

Tire section names

Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer

Uniform Tire Quality Grading

This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.

Your Toyota dealer will help answer any questions you may have as you read this information.

■ DOT quality grades

All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

574

6-1. Specifications

■ Treadwear

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

■ Traction AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turn- ing) traction.

■ Temperature A, B, C

The temperature grades are A (the highest), B, and C, represent- ing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speci- fied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passen- ger car tires must meet under the Federal Motor Vehicle Safety Stan- dard No. 109. Grades B and A represent higher levels of performance on the labo- ratory test wheel than the minimum required by law.

575