2010 Toyota Highlander Owners Manual

of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

NOTICE

■To prevent the water damage

Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ●Water entering the engine air intake will cause severe engine damage. ●Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ulti- mately damage.

●Water can wash the grease from wheel bearings, causing rusting and pre- mature failure, and may also enter the differentials, transmission and transfer case, reducing the gear oil’s lubricating qualities.

231

2-5. Driving information

NOTICE

■When you drive through water

If driving through water, such as when crossing shallow streams, first check the depth of the water and the bottom of the river bed for firmness. Drive slowly and avoid deep water.

■Inspection after off-road driving

●Sand and mud that has accumulated in brake drums and around brake discs may affect braking efficiency and may damage brake system compo- nents.

●Always perform a maintenance inspection after each day of off-road driv- ing that has taken you through rough terrain, sand, mud, or water. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

232

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever

possible. Be sure all items are secured in place.

● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit⎯ (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle's placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 - 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

233

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 1200 lb. (544
kg), the available amount of cargo and luggage load capacity will be as follows: 1200 lb. - 366 lb. = 834 lb. (544 kg -166 kg = 378 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

834 lb. - 388 lb. = 446 lb. (378 kg - 176 kg = 202 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

234

2

2-5. Driving information

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment. ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Luggage cover • Instrument panel • Dashboard • Auxiliary box or tray that has no lid

●Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer serious bodily injury, in the event of sudden braking or an accident.

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

235

2-5. Driving information

CAUTION

■Roof luggage carrier precautions

To use the roof rails as a roof luggage carrier, you must fit the roof rails with two or more genuine Toyota cross rails or their equivalent. When you load cargo on the roof luggage carrier, observe the following:

Cross rails

●Place the cargo so that its weight is distributed evenly between the front and rear axles.

●If loading long or wide cargo, never exceed the vehicle overall length or width. (→P. 552)

Roof rails

●Before driving, make sure the cargo is securely fastened on the roof

luggage carrier.

●Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly and result in death or serious injury.

●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cargo remains in its place.

●Do not exceed 100 lb. (45 kg) cargo weight on the roof luggage carrier.

236

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 1200 lb. (544 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 or 7 occupants (Front 2, Rear 3 or 5)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

■ Towing capacity

2.7 L 4-cylinder (1AR-FE) engine

Without towing package: 1500 lb. (680 kg) With towing package: 3500 lb. (1500 kg)

3.5 L V6 (2GR-FE) engine

Without towing package: 2000 lb. (900 kg) With towing package: 5000 lb. (2000 kg) Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 463)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

237

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Observe the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

238

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released.

Selecting tire chains

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain 0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length Cross chain 0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the front tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

239

2-5. Driving information

■Tire chains

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires. ●Install tire chains following the instructions provided in the accompanying

manual.

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the specified size. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Snow tires should be installed on all wheels.

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking. ●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

240

2-5. Driving information

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

241

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger carrying vehicle. Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer's characteristics and operating condi- tions. The vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as a towing kit.

242

2-5. Driving information

Weight limits

Confirm that the gross trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

lb. (kg)

Towing capacity

2.7 L 4-cylinder (1AR-FE) engine

3.5 L V6

(2GR-FE) engine

Without towing package With towing package

1500 (680) 3500 (1500)

2000 (900) 5000 (2000)

● The gross trailer weight must never exceed towing capacity

described in the table above.

● The gross vehicle weight must never exceed the GVWR indi- cated the Certification Label.

● The gross axle weight on each axle must never exceed the GAWR indicated the Certifica- tion Label.

243

2-5. Driving information

Towing related term

Towing related term

Meaning

GVWR (Gross Vehicle Weight Rating)

GAWR (Gross Axle Weight Rating)

Gross trailer weight

Towing capacity

Tongue load

The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the tongue load. The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear). The sum of the trailer weight and the weight of the cargo in the trailer The maximum allowable gross trailer weight. Towing capacity is calculated considering the base vehicle with neces- sary vehicle equipment and occupants. Additional optional equipment, passen- gers and cargo in the vehicle will reduce the towing capacity, gross trailer weight include the trailer, cargo and necessary equipment for towing. The load placed on the trailer hitch ball

244

2

2-5. Driving information

Trailer tongue load

● A recommended tongue load varies in accordance with the types

of trailers or towing as described below.

● In order to ensure the recommended values shown below, the

trailer must be loaded by referring to the following instructions. The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the gross trailer weight, not exceeding the following. 2.7 L 4-cylinder (1AR-FE) engine Without towing package: 150 lb. (68 kg) With towing package: 350 lb. (150 kg) 3.5 L V6 (2GR-FE) engine Without towing package: 200 lb. (90 kg) With towing package: 500 lb. (200 kg) (Tongue load / Gross trailer weight x 100 = 9 to 11%) If the gross trailer weight is over 2000 lbs. (900 kg), it is necessary to use a sway control device with sufficient capacity.

The gross trailer weight and tongue load can be measured with plat- form scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

Gross trailer weight Tongue load

245

2-5. Driving information

Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maxi- mum weight rating specified for the trailer hitch.

Trailer towing tips

Your vehicle will handle differently when towing a trailer. The 3 main causes of vehicle-trailer accidents are driver error, excessive speed and improper trailer loading. Keep the following in mind when towing. ● Before starting out, check the trailer lights and the vehicle-trailer

connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing turns.

246

2

2-5. Driving information

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

● Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● 2.7 L 4-cylinder (1AR-FE) engine: In order to maintain engine brak- ing efficiency when driving on a long steep downgrade, do not use overdrive. Transmission shift range position must be in 5 in S mode.

● 3.5 L V6 (2GR-FE) engine: In order to maintain engine braking effi- ciency when driving on a long steep downgrade, do not use over- drive. Transmission shift range position must be in 4 in S mode.

● Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 545)

247

2-5. Driving information

● Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoidable, do so only after performing the following:

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P and turn off the engine.

● When restarting after parking on a slope: STEP 1

With the transmission in the P position, start the engine. Be sure to keep the brake pedal pressed. Shift into 3, 2, 1, or the R position (if reversing). Release the parking brake and brake pedal and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

STEP 2

STEP 3

STEP 4

248

2

2-5. Driving information

■Before towing

Check that the following conditions are met: ●The vehicle's tires are properly inflated. (→P. 562) ●Trailer tires are inflated according to the trailer manufacturer's recom-

mendation.

●All trailer lights work. ●All lights work each time you connect them. ●The vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to all applicable federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. ■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential and wheel bearing), Toyota recommends that you do not tow a trailer until it has been driven for over 2000 miles (3200 km). However, avoid full throttle acceleration.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

249

2-5. Driving information

CAUTION

■Trailer towing precautions

●Follow all the instructions described in this section. Failure to do so could

cause an accident resulting in death or serious injury.

●Exceeding the towing capacity, GVWR or GAWR can cause an accident

resulting in death or serious personal injuries.

■To avoid accident or injury

●Do not exceed 45 mph (72 km/h) or the posted towing speed limit, which- ever is lower. As instability (swaying) of the towing vehicle-trailer combina- tion increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

●Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

●Do not use cruise control when you are towing. ●Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

●Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

●Do not tow the vehicle with the compact spare tire installed.

■Hitches

●If you wish to install a trailer hitch, contact your Toyota dealer. ●Use only a hitch that conforms to the gross trailer weight requirement. ●2.7 L 4-cylinder (1AR-FE) engine: The towing capacity of 3500 lb. (1500
kg) can only be guaranteed when using a genuine Toyota hitch assembly or equivalent.

●3.5 L V6 (2GR-FE) engine: The towing capacity of 5000 lb. (2000 kg) can only be guaranteed when using a genuine Toyota hitch assembly or equiv- alent.

●Follow the directions supplied by the hitch manufacturer.

250

2-5. Driving information

CAUTION

●Lubricate the hitch ball with a light coat of grease. ●Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

■When towing a trailer

●If the gross trailer weight exceeds 1000 lb. (453 kg), trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

●Never tap into your vehicle's hydraulic system, as this will lower the vehi-

cle's braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

NOTICE

■When installing a trailer hitch

●Use only the position recommended by your Toyota dealer. Do not install

the trailer hitch on the bumper as this may cause body damage.

●Do not use axle-mounted hitches, as they can cause damage to the axle

housing, wheel bearings, wheels or tires.

■Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

■Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle's electrical system and cause a malfunction.

251

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with 4 wheels on the ground.

252

2-5. Driving information

253

3-1. Using the air conditioning system and defogger Front manual air conditioning system∗

Fan speed control dial

Temperature control dial

Outside air or recirculated air mode

Air outlet selection dial

Rear air conditioning on/off switch∗

Air conditioning on/off switch

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

is not pressed, the system will blow ambient temperature air or

If heated air. For quick cooling, turn the temperature selector knob to the “MAX A/C” position. The air conditioning will automatically turn on in (recir- culated air) mode.

256

∗: If equipped

3-1. Using the air conditioning system and defogger

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Turn the dial to “OFF” to turn the fan off.

■ Changing the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can be also selected for more detailed adjustment.

Upper body

: Vehicles without rear air conditioning system

Upper body and feet

: Vehicles without rear air conditioning system

257

3-1. Using the air conditioning system and defogger

Feet

: Vehicles without rear air conditioning system

Without rear air conditioning system

Feet and windshield

With rear air conditioning system

Feet and windshield

258

3-1. Using the air conditioning system and defogger

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (indicator off) and recircu-

lated air mode (indicator on) modes each time

is pressed.

Defogging the windshield

Set the air outlet selection dial to

position. The air conditioning system oper- ates automatically. Recirculated air mode may auto- matically switch to outside air mode.

259

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Front center outlets

Direct air flow to the left or right, up or down.

Front side outlets

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

Rear center outlets (vehicles without rear air conditioning system) Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

260

3-1. Using the air conditioning system and defogger

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■Window defogger feature

In order to prevent the windows from fogging up, recirculated air mode may automatically switch to outside air mode if the ambient temperature drops. This feature can be cancelled by pushing and holding the air intake mode switch for longer than 2 seconds. The feature will be reactivated when the engine switch is turned to the “ACC” or “LOCK” position. ■When outside air temperature approaches 32°F (0°C) The air conditioning system may not operate even when

is pressed.

■When the indicator light on

engine only)

flashes (2.7 L 4-cylinder (1AR-FE)

Press and turn off the air conditioning system before turning it on once more. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature adjust- ment dial.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

261

3-1. Using the air conditioning system and defogger

CAUTION

■To prevent the windshield from fogging up

Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

262

3-1. Using the air conditioning system and defogger Front automatic air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting. Control panel

Temperature control for rear passengers

Windshield defogger

Automatic mode

Driver's side temperature control dial

Off

Rear air conditioning on/off switch

Fan speed

Outside air or recirculated air mode

Individual mode

Front passenger’s side temperature control dial

Changes the air outlets used Vehicles with rear air conditioning system Vehicles without rear air conditioning system

Simultaneous mode

Air conditioning on/off switch

∗: If equipped 263

3-1. Using the air conditioning system and defogger

Multi-information display

Airflow display

Fan speed display

Driver’s side temperature setting dis- play

Temperature setting dis- play for rear passengers

Front passenger’s side tem- perature setting display

Using the automatic mode

STEP 1

Press

The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting. “AUTO” will be displayed on the multi-information display.

STEP 2

Turn the temperature control dial clockwise (warm) or coun- terclockwise (cool). Air outlets and fan speed for the right-hand and left-hand seats may be set separately depending on the temperature setting.

264

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). The air conditioning system switches between individual and simultaneous modes each time (without rear air conditioning system) or Simultaneous mode: Only the driver’s side temperature control dial can be used to adjust the temperature for all seats. The indicator status will be as follows: Without rear air conditioning system:

(with rear air conditioning system) is pressed.

(off)

With rear air conditioning system:

(on)

Individual mode: The temperature for the driver’s, front passen- ger’s and rear seats (→P. 274) can be adjusted separately. Operat- ing the passenger's side or rear (with rear air conditioning system) temperature control will enter individual mode. The indicator status will be as follows: Without rear air conditioning system:

(on)

With rear air conditioning system:

(off)

■ Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on

or

The fan speed is shown on the multi-information display. (7 levels) Press

to turn the fan off.

265

3-1. Using the air conditioning system and defogger

■ Changing the air outlets

Press The air outlets switch each time either side of flow shown on the display indicates the following. Upper body

is pressed. The air

: Vehicles without rear air conditioning system

Upper body and feet

: Vehicles without rear air conditioning system

Feet

: Vehicles without rear air conditioning system

266

3-1. Using the air conditioning system and defogger

Without rear air conditioning system

Feet and windshield

With rear air conditioning system

Feet and windshield

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (indicator off) and recircu-

lated air mode (indicator on) modes each time

is pressed.

267

3-1. Using the air conditioning system and defogger

Changing the rear seat settings (if equipped)

■ Adjusting the temperature setting

to increase the temperature and “∨” to

Press “∧” on decrease the temperature. The air conditioning system switches between individual and simultaneous modes each time

is pressed.

Defogging the windshield

Press

The air conditioning system oper- ates automatically.

Adjusting the position of and opening and closing the air outlets

Front center outlets

Direct air flow to the left or right, up or down.

268

3-1. Using the air conditioning system and defogger

Front side outlets

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

Rear center outlets (vehicles without rear air conditioning system) Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

■Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. ●The system may switch automatically to recirculated mode when the

coolest temperature setting is selected in summer.

●Immediately after the switch is pressed, the fan may stop for a while until

warm or cool air is ready to flow.

●Cool air may flow to the area around the upper body when the heater is

on.

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

269

3-1. Using the air conditioning system and defogger

■Window defogger feature

Recirculated air mode may automatically switch to in situations where the windows need to be defogged. ■When outside temperature approaches 32°F (0°C)

(outside air) mode

The air conditioning system may not operate even when

is pressed.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.

CAUTION

■To prevent the windshield from fogging up

Do not use

during cool air operation in extremely humid weather. The

difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

270

3-1. Using the air conditioning system and defogger Rear manual air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting.

Changes the air outlets used

Fan speed control dial

Temperature control dial

∗: If equipped 271

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

■ Changing the air outlets

Press the desired

or

Air flows as shown below according to the mode selected.

Upper body

Upper body and feet

272

3-1. Using the air conditioning system and defogger

Feet

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease).

Adjusting the position of and opening and closing the roof side air outlets

Direct air flow to the left or right, up or down.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

273

3-1. Using the air conditioning system and defogger Rear automatic air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting.

Airflow display

Fan speed display

Temperature setting display

Fan speed control dial

Temperature control dial

Off

Automatic mode

Changes the air outlets used

Using the automatic mode

STEP 1

Press

The air conditioning system will operate, and air outlets and fan speed will be set automatically. “AUTO” will be displayed on the control panel.

STEP 2

Turn the temperature control dial clockwise (warm) or coun- terclockwise (cool).

274

∗: If equipped

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

■ Changing the air outlets

Press

The air outlets change as follows each time

is pressed.

Air flows as shown below according to the mode selected.

Upper body

Upper body and feet

275

3-1. Using the air conditioning system and defogger

Feet

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease).

Press

to turn the fan off.

Adjusting the position of and opening and closing the roof side air outlets

Direct air flow to the left or right, up or down.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

276

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

Clear the rear window using the defogger.

Vehicles with manual air conditioning system

On/off

Press the button to turn on the rear window defogger. The indicator light will come on. The defoggers will automati- cally turn off after 15 to 60 min- time utes. The operation changes according to the ambient temperature and vehi- cle speed. Pressing the button again also turns the defogger off.

Vehicles without outside rear view mirror defoggers Vehicles with outside rear view mirror defoggers Vehicles with automatic air conditioning system

On/off

Press the button to turn on the rear window defogger. The indicator light will come on. The defoggers will automati- cally turn off after 15 to 60 min- time utes. The operation changes according to the ambient temperature and vehi- cle speed. Pressing the button again also turns the defogger off.

Vehicles without outside rear view mirror defoggers Vehicles with outside rear view mirror defoggers

277

3-1. Using the air conditioning system and defogger

■The defogger can be operated when

Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.

278

3-1. Using the air conditioning system and defogger Windshield wiper de-icer∗

This feature is used to prevent ice from building up on the wind- shield and wiper blades.

On/off

Press the button to turn on the windshield wiper de-icer. The indicator light will come on. The windshield wiper de-icer will automatically turn off after approximately 15 minutes.

■The de-icer can be operated when Vehicles without smart key system

The engine switch is in the “ON” position.

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

CAUTION

■When the windshield wiper de-icer is on

Do not touch the glass at the lower part of the windshield or to the side of the front pillars as the surfaces can become very hot and burn you.

∗: If equipped 279

3-1. Using the air conditioning system and defogger Using the steering wheel climate remote control switches∗

Some air conditioning features can be controlled using the switches on the steering wheel.

Temperature control Off Automatic mode

Using the automatic mode

STEP 1

Press

The air conditioning system will operate, and air outlets and fan speed will be set automatically. “AUTO” will be displayed on the multi-information display.

STEP 2

Press “∧” on decrease the temperature.

to increase the temperature and “∨” to

Adjusting the temperature setting

to increase the temperature and “∨” to decrease

Press “∧” on the temperature.

Turning off the fan

Press

280

∗: If equipped

3-2. Using the audio system Audio system

With navigation system

Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.

Without navigation system

Type A: CD player and AM/FM radio (with CD changer controller)

Type B: CD player with changer and AM/FM radio

281

3-2. Using the audio system

Type C: CD player with changer and AM/FM radio

Title

Using the radio Using the CD player Playing back MP3 and WMA discs Optimal use of the audio system Using the AUX adapter Using the steering wheel audio switches

Page P. 284
P. 290
P. 297
P. 304
P. 307
P. 309

■Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

282

3-2. Using the audio system

CAUTION

■For vehicles sold in U.S.A. and Canada

●Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

●Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

NOTICE

■To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine is off.

■To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

283

3-2. Using the audio system Using the radio

Power

Volume

Scanning for receivable stations

Station selector

Seeking the frequency

AM/AM·SAT*/FM mode buttons

Adjusting the frequency (AM, FM mode) or channel (SAT mode)

*: Type B and C

Changing the program type

Setting station presets (excluding XM® Satellite Radio)

STEP 1

Search for desired stations by turning the

or pressing

“∧” or “∨” on

STEP 2

Press and hold the button (from to be set to until you hear a beep.

to

) the station is

Scanning radio stations (excluding XM® Satellite Radio)

■ Scanning the preset radio stations STEP 1

Press and hold until you hear a beep. Preset stations will be played for 5 seconds each. When the desired station is reached, press

STEP 2

284

once again.

3-2. Using the audio system

■ Scanning all radio stations within range STEP 1

Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press

STEP 2

once again.

XM® Satellite Radio (type B and C) ■ Receiving XM® Satellite Radio STEP 1

until SAT appears in the display.

Press and hold The display changes as follows each time pressed. AM → SAT1 → SAT2 → SAT3

is

STEP 2

Turn

to select the desired channel in all categories, or

press “∧” or “∨” on

to select the desired channel in the

current category.

■ Setting XM® Satellite Radio channel presets

the desired channel. Press and hold

the button ) the channel is to be set to until you hear a

to

Select (from beep.

■ Changing the channel category

Press “∧” or “∨” on the

■ Scanning XM® Satellite Radio channels

● Scanning channels in the current category

STEP 1

STEP 2

Press When the desired channel is reached, press again.

285

3-2. Using the audio system

● Scanning preset channels

STEP 1

STEP 2

Press and hold When the desired channel is reached, press again.

until you hear a beep.

■ Displaying text information

Press The display will show up to 10 characters. The display changes as follows each time the button is pressed. ● CH NAME ● TITLE (SONG/PROGRAM TITLE) ● NAME (ARTIST NAME/FEATURE) ● CH NUMBER

Silencing a sound (type A only)

Press

286

3-2. Using the audio system

■When the battery is disconnected

Stations presets are erased.

■Reception sensitivity

●Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains and transmitters.

●Mast type antenna ⎯ The radio antenna is mounted on the right-side

front fender. The antenna can be removed from the base by turning it.

●Print type antenna ⎯ The radio antenna is mounted inside the left-side rear quarter window. To maintain clear radio reception, do not attach metallic window tinting or other metallic objects to the antenna wire mounted inside the left-side rear quarter window.

■XM® Satellite Radio (type B and C)