2012 Toyota FJ Cruiser Owners Manual

IC ID: 775E-K025
MADE IN JAPAN

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

295

3-4. Using the hands-free phone system (for cellular phone)

CAUTION

■FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply with- out maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 7.9 in. (20 cm) and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

■Caution while driving

Do not use a cellular phone, or connect the Bluetooth® phone.

NOTICE

■To prevent damage to a cellular phone

Do not leave a cellular phone in the vehicle. The temperature inside may become high resulting in damage to the phone.

296

3-4. Using the hands-free phone system (for cellular phone) Using the hands-free phone system (for cellular phone)

■ Audio unit

Display A message, name, phone number, etc. is displayed.

Lower-case characters and special characters, such as an umlaut, cannot be dis- played.

Selects speed dials Selects items such as menu or number Turn: Selects an item Press: Inputs the selected item Bluetooth® connection con- dition and reception level

If “BT” is not displayed, the hands-free phone system cannot be used.

297

3-4. Using the hands-free phone system (for cellular phone)

■ Steering wheel switches

Volume The voice guidance volume cannot be adjusted using this button. Off-hook switch Turns the hands-free sys- tem on/starts a call On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Talk switch Turns the voice command system on (press)/turns the voice command system off (press and hold)

298

3-4. Using the hands-free phone system (for cellular phone)

■ Microphone

299

3-4. Using the hands-free phone system (for cellular phone)

Operating the system by using a voice command

By following the voice guidance instructions output from the speaker, voice commands enable the operation of the hands-free phone sys-

tem without the need to check the display or operate

■ Operation procedure when using a voice command

Press the talk switch and follow the voice guidance instructions.

■ Auxiliary commands when using a voice command

The following auxiliary commands can be used when operating the system using a voice command: “Cancel”: Exits the hands-free phone system “Repeat”: Repeats the previous voice guidance instruction “Go back”: Returns to the previous procedure “Help”: Reads aloud the function summary if a help comment is registered for the selected function

Using the hands-free phone system for the first time

Before using the hands-free phone system, it is necessary to register a cellular phone in the system. The phone registration mode will be entered automatically when starting the system with no cellular phone registered. Follow the procedure below to register a cellular phone:

Press the off-hook switch or the talk switch.

The introductory guidance and phone name registration instructions are heard.

Select “Pair Phone” using a voice command or

300

3-4. Using the hands-free phone system (for cellular phone)

Register a phone name either of the following methods.

a. Select “Record Name” using

, and say a name to

be registered.

b. Press the talk switch and say a name to be registered.

A voice guidance instruction to confirm the input is heard.

Select “Confirm” using a voice command or

Registration to the hands-free phone system only

Select “Phone Only” using a voice command or

Registration to the hands-free phone system and Bluetooth® audio system at the same time

Select “Int. Audio (Internal Audio)” using a voice command or

Select “Confirm” using a voice command or

A passkey is displayed and heard, and a voice guidance instruction for inputting the passkey into the cellular phone is heard.

Input the passkey into the cellular phone. Refer to the manual that comes with the cellular phone for the oper- ation of the phone.

Guidance for registration completion is heard.

301

3-4. Using the hands-free phone system (for cellular phone)

Menu list of the hands-free phone system

■ Normal operation

Second menu

Third menu

Operation detail

Add Entry Change Name Delete Entry Delete Speed Dial List Names Speed Dial (Set speed dial)

Dialing a number stored in the incoming call history memory Dialing a number stored in the outgoing call history memory

Dialing by inputting a number

Dialing by inputting a name registered in the phone book

Adding a new number Changing a name in the phone book Deleting the phone book data Deleting a registered speed dial

Listing the phone book data

Registering a speed dial

First menu

CallBack (Callback)

Redial

Dial by Number Dial by Name (Dial by name)

Phonebook

302

3-4. Using the hands-free phone system (for cellular phone)

First menu

Second menu

Third menu

Operation detail

Security

Setup

Phone Setup

System Setup

Set PIN Phonebook Lock (Phone book lock) Phonebook Unlock (Phone book unlock)

Pair Phone

Change Phone Name (Change name)

Delete Phone

List phones

Select Phone

Set Passkey Handsfree Power Guidance Volume

Device Name

Reset Settings

Setting a PIN code

Locking the phone book

Unlocking the phone book

Registering the cellular phone to be used

Changing a registered name of a cellular phone

Deleting a registered cellular phone Listing the registered cellu- lar phones Selecting a cellular phone to be used Changing the passkey Setting the hands-free power on/off Setting voice guidance vol- ume Displaying a device informa- tion Initialization

303

3-4. Using the hands-free phone system (for cellular phone)

■ Using a short cut key

First menu

Second menu

Operation detail

Dial XXX (name)

Dial XXX (number) Phone book add entry Phone book change name Phone book delete entry Phone book set speed dial Phone book delete speed dial Phone book List names

Dialing a number registered in the phone book Dialing the input numbers

Adding a new number

Changing the name of a phone number in the phone book

Deleting phone book data

Registering a speed dial

Deleting a speed dial

Listing the phone book data

304

3-4. Using the hands-free phone system (for cellular phone)

■Automatic volume adjustment

When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less.

■When using a voice command

For numbers, say a combination of single digits from zero to nine, # (pound), ∗ (star), and + (plus). Say a command correctly and clearly.

■Situations that the system may not recognize your voice

●When driving on a rough road ●When driving at high speeds ●When air is blowing out of the vents onto the microphone ●When the air conditioning fan emits a loud noise

■Operations that cannot be performed while driving

●Operating the system with

●Registering a cellular phone to the system

■Changing the passkey

→P. 315

305

3-4. Using the hands-free phone system (for cellular phone) Making a phone call

■ Making a phone call

● Dialing by inputting a number

“Dial by Number”

● Dialing by inputting a name

“Dial by Name (Dial by name)”

● Speed dialing ● Dialing a number stored in the outgoing history memory

“Redial”

● Dialing a number stored in the incoming history memory

“CallBack (Callback)” ■ Receiving a phone call

● Answering the phone call ● Refusing the phone call ■ Transferring a phone call ■ Using the call history memory

● Dialing ● Storing data in the phone book ● Deleting

306

3-4. Using the hands-free phone system (for cellular phone)

Dialing by inputting a number

Press the talk switch and say “Dial by Number”. Press the talk switch and say the phone number. Dial by one of the following methods: a. Press the off-hook switch. b. Press the talk switch and say “Dial”.

c. Select “Dial” using

Dialing by inputting a name

Press the talk switch and say “Dial by Name”. Select a registered name to be input by either of the following methods: a. Press the talk switch and say a registered name. b. Press the talk switch and say “List names”. Press the talk

switch while the desired name is being read aloud.

Dial by one of the following methods: a. Press the off-hook switch. b. Press the talk switch and say “Dial”.

c. Select “Dial” using

Speed dialing

Press the off-hook switch. Press the preset button in which the desired number is regis- tered. Press the off-hook switch.

307

3-4. Using the hands-free phone system (for cellular phone)

When receiving a phone call

■ Answering a phone call Press the off-hook switch.

■ Refusing a phone call

Press the on-hook switch.

Transferring a call

A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the follow- ing methods:

a. Operate the cellular phone.

Refer to the manual that comes with the cellular phone for the oper- ation of the phone.

b. Press the off-hook switch*1. c. Press the talk switch and say “Call Transfer”*2. *1: This operation can be performed only when transferring a call

from the cellular phone to the system during a call.

*2: While the vehicle is in motion, a call cannot be transferred from the system to the cellular phone. Also, this operation is invalid while dialing or receiving a call.

308

3-4. Using the hands-free phone system (for cellular phone)

Using the call history memory

Follow the procedure below to use a number stored in the call history memory:

Press the talk switch and say “Redial” (when using a number stored in the outgoing call history memory) or “CallBack” (when using a number stored in the incoming call history memory). Select the number by either of the following methods: a. Say “Previous” or “Go back” until the desired number is dis-

played.

b. Select the desired number using

The following operations can be performed:

Dialing: Press the off-hook switch or select “Dial” using a voice

command or

Storing the number in the phone book: Select “Store” using a voice

command or

Deleting: Select “Delete” using a voice command or

309

3-4. Using the hands-free phone system (for cellular phone)

■Call history

Up to 5 numbers can be stored in each of the outgoing and incoming call his- tory memories.

■When talking on the phone

●Do not talk at the same time as the other party. ●Keep the volume of the received voice down. Otherwise, voice echo will

increase.

310

3-4. Using the hands-free phone system (for cellular phone) Setting a cellular phone

Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below using a

voice command or

● Registering a cellular phone

1. “Setup” → 2. “Phone Setup” → 3. “Pair Phone”

● Selecting the cellular phone to be used

1. “Setup” → 2. “Phone Setup” → 3. “Select Phone”

● Changing a registered name

1. “Setup” → 2. “Phone Setup” → 3. “Change Phone Name (Change name)”

● Listing the registered cellular phones

1. “Setup” → 2. “Phone Setup” → 3. “List Phones”

● Deleting a cellular phone

1. “Setup” → 2. “Phone Setup” → 3. “Delete Phone”

● Changing the passkey

1. “Setup” → 2. “Phone Setup” → 3. “Set Passkey”

● Turning the hands-free phone automatic connection on/off

1. “Setup” → 2. “Phone Setup” → 3. “Handsfree Power”

311

3-4. Using the hands-free phone system (for cellular phone)

Registering a cellular phone

Select “Pair Phone” using a voice command or

, and per-

form the procedure for registering a cellular phone. (→P. 300)

Selecting the cellular phone to be used

Select “Select Phone” using a voice command or

Pattern A

Select the cellular phone to be used by either of the following methods, and select “Confirm” using a voice command or

a. Press the talk switch and say the desired phone name. b. Press the talk switch and say “List phones”. While the name of the desired cellular phone is being read aloud, press the talk switch.

Pattern B

Select the cellular phone to be used using

312

3-4. Using the hands-free phone system (for cellular phone)

Changing a registered name

Select “Change Phone Name (Change name)” using a voice

command or

Select the name of the cellular phone to be changed by either of the following methods: a. Press the talk switch and say the desired phone name, and

select “Confirm” using a voice command or

b. Press the talk switch and say “List phones”. While the desired phone name is being read aloud, press the talk switch.

c. Select the desired phone name using

Press the talk switch or select “Record Name” using

, and say a new name.

Select “Confirm” using a voice command or

313

3-4. Using the hands-free phone system (for cellular phone)

Listing the registered cellular phones

Selecting “List Phones” using a voice command or

causes

the list of registered cellular phones to be read aloud. When listing is complete, the system returns to “Phone Setup”. Pressing the talk switch while the name of a cellular phone is being read selects the cellular phone, and the following functions will be available: • Selecting a cellular phone: “Select Phone” • Changing a registered name: “Change Name” • Deleting a cellular phone: “Delete Phone”

Deleting a cellular phone

Select “Delete Phone” using a voice command or

Select the cellular phone to be deleted by either of the follow- ing methods and select “Confirm” using a voice command or

a. Press the talk switch and say the name of the desired cellu-

lar phone.

b. Press the talk switch and say “List phones”. While the name of the desired cellular phone is being read aloud, press the talk switch.

314

3-4. Using the hands-free phone system (for cellular phone)

Changing the passkey

Select “Set Passkey” using a voice command or

Press the talk switch, say a 4 to 8-digit number, and select

“Confirm” using a voice command or

The number should be input 1 digit at a time. When the entire number to be registered as a passkey has

been input, press

again.

Turning the hands-free phone automatic connection on/off

■ Turning off the automatic connection

Select “Handsfree Power” using a voice command or

Select “Turn off” using a voice command or

315

3-4. Using the hands-free phone system (for cellular phone)

■ Turning on the automatic connection

Select “Handsfree Power” using a voice command or

Select “Turn on” using a voice command or

■The number of cellular phones that can be registered Up to 6 cellular phones can be registered in the system.

316

3-4. Using the hands-free phone system (for cellular phone) Security and system setup

To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure

● Setting or changing the PIN (Personal Identification Number)

1. “Setup” → 2. “Security” → 3. “Set PIN”

● Locking the phone book

1. “Setup” → 2. “Security” → 3. “Phonebook Lock”

● Unlocking the phone book

1. “Setup” → 2. “Security” → 3. “Phonebook Unlock”

■ System setup items and operation procedure

● Setting voice guidance volume

1. “Setup” → 2. “System Setup” → 3. “Guidance Volume”

● Displaying the Bluetooth® device address and name 1. “Setup” → 2. “System Setup” → 3. “Device Name”

● Initialization

1. “Setup” → 2. “System Setup” → 3. “Reset Settings”

can only be used for system setup operation.

317

3-4. Using the hands-free phone system (for cellular phone)

Setting or changing the PIN

■ Setting a PIN

Select “Set PIN” using a voice command or

Enter a PIN using a voice command or

When using

, input the code 1 digit at a time.

■ Changing the PIN

Select “Set PIN” using a voice command or

Enter the registered PIN using a voice command or

Enter a new PIN using a voice command or

When using

, input the code 1 digit at a time.

318

3-4. Using the hands-free phone system (for cellular phone)

Locking or unlocking the phone book

Select “Phonebook Lock (Phone book lock)” or “Phonebook Unlock (Phone book unlock)” using a voice command or

Input the PIN by either of the following methods and select

“Confirm” using a voice command or

a. Press the talk switch and say the registered PIN.

b. Input a new PIN using

Setting voice guidance volume

Select “Guidance Volume” using

Change the voice guidance volume.

To decrease the volume: Turn

counterclockwise.

To increase the volume: Turn

clockwise.

319

3-4. Using the hands-free phone system (for cellular phone)

Displaying the Bluetooth® device address and name

Select “Device Name” using

to display the Bluetooth® device address and

Turn

name.

Select “Go Back” using

to return to “System Setup”.

Initialization

Select “Reset Settings” and then “Confirm” using

Select “Confirm” using

320

3-4. Using the hands-free phone system (for cellular phone)

■Initialization

●The following data in the system can be initialized:

• Phone book • Outgoing and incoming call history • Speed dials • Registered cellular phone data • Security code

●Once the initialization has been completed, the data cannot be restored

to its original state.

■When the phone book is locked

The following functions cannot be used: ●Dialing by inputting a name ●Speed dialing ●Dialing a number stored in the call history memory ●Using the phone book

321

3-4. Using the hands-free phone system (for cellular phone) Using the phone book

To enter the menu of each setting, follow the steps below:

● Adding a new phone number

1. “Phonebook” → 2. “Add Entry”

● Setting speed dial

1. “Phonebook” → 2. “Speed Dial (Set speed dial)”

● Changing a registered name

1. “Phonebook” → 2. “Change Name”

● Deleting registered data

1. “Phonebook” → 2. “Delete Entry”

● Deleting speed dial

1. “Phonebook” → 2. “Delete Speed Dial”

● Listing the registered data

1. “Phonebook” → 2. “List Names”

Adding a new phone number

The following methods can be used to add a new phone number: ● Inputting a phone number using a voice command ● Transferring data from the cellular phone

● Inputting a phone number using

● Selecting a phone number from outgoing or incoming call history

322

3-4. Using the hands-free phone system (for cellular phone)

■ Adding procedure

Select “Add Entry” using a voice command or

Use one of the following methods to input a telephone num- ber:

Inputting a telephone number using a voice command

STEP2-1 Select “By Voice (By voice)” using a voice com-

mand or

STEP2-2 Press the talk switch, say the desired number, and

select “Confirm” using a voice command.

Transferring data from the cellular phone

STEP2-1 Select “By Phone” and then “Confirm” using a voice

command or

STEP2-2 Transfer the data from the cellular phone.

Refer to the manual that comes with the cellular phone for the details of transferring data.

STEP2-3 Select the data to be registered by either of the fol-

lowing methods: a. Say “Previous” or “Next” until the desired data is displayed, and select “Confirm” using a voice command.

b. Select the desired data using

323

3-4. Using the hands-free phone system (for cellular phone)

Inputting a phone number using

STEP2-1 Select “Manual Input” using

STEP2-2 Input a phone number using

, and press

once again.

Input the phone number 1 digit at a time.

Selecting a phone number from outgoing or incoming call history

STEP2-1 Select “Call History” using a voice command or

STEP2-2 Select

“Outgoing Call History

(Outgoing)” or “Incoming Call History (Incoming)” using a voice

command or

STEP2-3 Select the data to be registered by either of the fol-

lowing methods: a. Say “Previous” or “Go back” until the desired data is displayed, and select “Confirm” using a voice command.

b. Select the desired data using

324

3-4. Using the hands-free phone system (for cellular phone)

Select the name to be registered by either of the following methods, and select “Confirm” using a voice command or

a. Press the talk switch and say the desired name.

b. Select “Record Name” using

, and say the desired

name.

Select “Confirm” using a voice command or

In , selecting “Speed Dial (Set speed dial)” instead of “Confirm” registers the newly added phone number as a speed dial.

325

3-4. Using the hands-free phone system (for cellular phone)

Setting speed dials

Select “Speed Dial (Set speed dial)” using a voice command

or

Select the data to be registered as a speed dial by either of the following methods: a. Press the talk switch, say desired number, and select

“Confirm” using a voice command or

b. Press the talk switch, and say “List names”. While the desired name is being read aloud, press the talk switch,

and select “Confirm” using a voice command or

c. Select the desired data using

Select the desired preset button, and register the data into speed dial by either of the following methods: a. Press the desired preset button, and select “Confirm” using

a voice command or

b. Press and hold the desired preset button.

326

3-4. Using the hands-free phone system (for cellular phone)

Changing a registered name

Select “Change Name” using a voice command or

Select the name to be changed by either of the following methods. a. Press the talk switch, say desired name, and select

“Confirm” using a voice command or

b. Press the talk switch, and say “List names”. While the desired name is being read aloud, press the talk switch and

select “Confirm” using a voice command or

c. Select the desired name using

Select “Record Name” with

or the talk switch.

Say a new name, and select “Confirm” using a voice com-

mand or

327

3-4. Using the hands-free phone system (for cellular phone)

Deleting registered data

Select “Delete Entry” using a voice command or

Select the data to be deleted by either of the following meth- ods, and select “Confirm” using a voice command or

a. Press the talk switch, and say the name of the desired

phone number to be deleted.

b. Press the talk switch and say “List phones”. While the name of the desired phone number is being read aloud, press the talk switch.

Deleting speed dials

Select “Delete Speed Dial” using a voice command or

Press the preset button for which the desired speed dial is registered, and select “Confirm” using a voice command or

328

3-4. Using the hands-free phone system (for cellular phone)

Listing the registered data

Selecting “List names” using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following functions will be available. • Dialing: “Dial” • Changing a registered name: “Change Name” • Deleting an entry: “Delete Entry” • Setting a speed dial: “Speed Dial (Set speed dial)”

■Limitation of number of digits

A phone number that exceeds 24 digits cannot be registered.

329

3-5. Using the interior lights Interior lights list

Rear interior light (→P. 331) Front interior light (→P. 331) Personal lights (→P. 332) Engine switch light

■Illuminated entry system

When the interior light switch is in the DOOR position, the interior light and engine switch light automatically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed and the engine switch position.

■To prevent the battery from being discharged

If the interior light remains on when the door is not fully closed and the inte- rior light switch is in the DOOR position, the light will go off automatically after 30 minutes.

330

3-5. Using the interior lights

Interior lights

■Customization that can be configured at Toyota dealer

Settings (e.g. The time elapsed before lights turn off) can be changed. (Cus- tomizable features →P. 507)

Interior lights

Front

Rear

DOOR position OFF ON

DOOR position OFF ON

331

3-5. Using the interior lights

Personal lights

Personal lights

On/off

■To prevent the battery from being discharged

The personal lights will automatically turn off in about 30 minutes after the key is removed from the engine switch.

332

3-6. Using the storage features List of storage features

Auxiliary box Glove box Bottle holders Cup holders

CAUTION

■Items that should not be left in the storage spaces

Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

●Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.

333

3-6. Using the storage features

Glove box

Glove box and cup holders (front)

Pull up the lever.

CAUTION

■Caution while driving

Keep the glove box closed. Injuries may result in the event of an accident or sudden braking.

Cup holders (front)

Vehicles with an automatic transmission

334

3-6. Using the storage features

Cup holders (front)

Vehicles with a manual transmission

■Holding large cups

Vehicles with an automatic transmission

The adapter can be removed.

335

3-6. Using the storage features

Cup holders (front)

Vehicles with a manual transmission

The adapter can be removed.

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or beverage cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.

336

3-6. Using the storage features

Cup holders (rear)

Cup holders (rear)

■Removing the mat

Pull up.

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or beverage cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.

337

3-6. Using the storage features

Bottle holders

Bottle holders

■Bottle holders

Depending on their size or shape, some bottles may not fit in the holders.

NOTICE

■Items that should not be stowed in the bottle holders

Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.

338

3-6. Using the storage features

Auxiliary box

Auxiliary box

Push the button.

Pull up the lid.

CAUTION

■Caution while driving

Keep the auxiliary box closed. Items may fall out and cause death or serious injury in case of an accident or sudden stop.

339

Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.

Flip down.

3-7. Other interior features Sun visors

Front

Side

340

3-7. Other interior features Vanity mirrors

Open the cover.

341

3-7. Other interior features Clock

Adjusts the hours Adjusts the minutes

■The clock is displayed when

The engine switch is in the ACC or ON position.

■When disconnecting and reconnecting battery terminals

The time display will automatically be set to 1:00.

342

3-7. Other interior features Outside temperature display∗

the outside air

Displays temperature. The temperature range that can be displayed is from -22°F (-30°C) to 122°F (50°C). the outside air Switches temperature display between English/U.S. Cus- tomary System and metric.

■When – –°C or – –°F is displayed

The system may be malfunctioning. Take your vehicle to your Toyota dealer.

■The outside air temperature is displayed when

The engine switch is in the ON position.

■When disconnecting and reconnecting battery terminals

The display will automatically be set to the initial mode.

■Display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

∗: If equipped 343

3-7. Other interior features Power outlet (12V DC)

The power outlet can be used for 12 V accessories that run on less than 10A.

■The power outlet can be used when

The engine switch is in the ACC or ON position.

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent the fuse from being blown

Do not use an accessory that uses more than 12V/10A.

■To prevent the battery discharge

Do not use the power outlet longer than necessary when the engine is not running.

344

3-7. Other interior features Power outlet (115V AC)∗

The power outlet can be used for electrical appliances. ■ Operation

Main switch To use the power outlet, turn on the main switch. The power supply starts a few seconds after the main switch is pressed. Power outlet socket

∗: If equipped 345

3-7. Other interior features

Maximum available capacity of the power outlet

■ While the vehicle is being driven

The maximum capacity of the power outlet is always 115V AC/ 100W.

■ When the vehicle is stationary

The maximum capacity of the power outlet varies depending on the following conditions. ● The maximum capacity is 115V AC/400W when the following

condition applies: • The shift lever is in P or N. (automatic transmission) • The shift lever is in N and the clutch pedal is not depressed.

(manual transmission)

A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condi- tion described above.

● The maximum capacity is 115V AC/100W when the following

condition applies: • The shift lever is moved to any positions other than P and N.

(automatic transmission)

• The clutch pedal is depressed. (manual transmission)

346

3-7. Other interior features

■The power outlet can be used when

The engine is started.

■The indicator light changes according the maximum available capacity,

as follows:

Indicates 115V AC/400W Indicates 115V AC/100W

■When the power outlet is in operation

The sound of the cooling fan may be heard from the right side of the luggage compartment. This is normal and does not indicate a malfunction. ■If the engine is started with the power outlet main switch on

The maximum capacity of the power supply may decrease to below the stan- dard, or may be cut off completely, even when the vehicle is stationary.

■The protection circuit may be activated to cut the power supply if any

of the following conditions apply: ●The engine is started with the power outlet main switch on. ●Use of electrical appliances exceeding the maximum capacity is

attempted.

A sound may be heard when the protection circuit is activated. This is normal and does not indicate a malfunction. ●Electrical appliances, which consume power exceeding 100W, have

been used continuously for a long time period.

●The total power usage by all electrical features (headlights, air condition- ing, etc.) has exceeded the total vehicle maximum for an extended period of time.

347

3-7. Other interior features

■If the protection circuit is activated and the power supply is cut, con-

duct the following procedure:

Park the vehicle in a safe place, and then securely apply the park- ing brake. Check and ensure the following conditions • The shift lever is in P or N. (automatic transmission) • The shift lever is in N and the clutch pedal is not depressed.

(manual transmission)

Make sure that the power consumption of the electric appliance is within the maximum capacity of the power outlet and the appliance is not broken. Press the power outlet main switch again.

When the cabin temperature is high, open the windows to cool the tempera- ture down. Once it reaches the normal temperature, turn the power outlet main switch on again. If the power supply is not resumed even after performing the above proce- dure, have the vehicle inspected by a Toyota dealer.

CAUTION

■Using a power outlet

Observe the following precautions to reduce the risk of injury. ●Use of the power outlet when it is wet with drinking water or snow may result in electrical shocks and is extremely dangerous. The power outlet must be thoroughly dried before use.

●Do not allow children to use or play with the power outlet. ●Be careful not to get any part of your body caught in the power outlet lid. ●When using electrical appliances, strictly follow any cautions and notices

written on their labels and in the manufacturers’ instruction manuals.

●Do not modify, disassemble or repair the power outlet or its inverter, in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs.

348

3-7. Other interior features

CAUTION

■To prevent injuries and accidents, securely fix all electric appliances before use and do not use any appliances that may do any of the fol- lowing: ●Distract the driver while driving, or hamper safe driving. ●Result in a fire or burn injuries due to the appliance rolling, falling or over-

heating while driving.

●Emit steam, while the windows of the cabin are closed.

■To prevent unexpected accidents, such as electric shocks, do not per-

form any of the following. ●Using the power outlet for electric heaters while sleeping. ●Contaminating the power outlet with liquid substances or mud. ●Handling electrical appliance plugs at the power outlet with wet hands or

feet.

●Inserting foreign objects into the power outlet. ●Using malfunctioning electric appliances. ●Inserting inappropriate or badly fitting plugs into the power outlet.

NOTICE

■To avoid damaging the power outlet and the plug

●Close the power outlet lid when not in use. ●Foreign objects or liquids that enter the power outlet may cause a short

circuit.

●Do not use plug adaptors to connect too many plugs to the power outlet. ●After inserting a plug, gently close the power outlet lid.

■To prevent the fuse from being blown

Do not use a 115V AC appliance that requires more than maximum capacity. If a 115V AC appliance that consumes more than maximum capacity is used, the protection circuit will cut the power supply.

349

3-7. Other interior features

NOTICE

■Appliances that may not operate properly (115V AC)

The following 115V AC appliances may not operate even if their power con- sumption is under maximum capacity. ●Appliances with high initial peak wattage ●Measuring devices that process precise data ●Other appliances that require an extremely stable power supply

■To prevent the battery from being discharged

Turn off all the vehicle’s electronic equipment and accessories, such as the headlights and air conditioning, when electrical appliances that consume in excess of 100W are used continuously for long periods of time.

■To prevent any damage caused by heat

Do not use any electrical appliances that give off intense heat such as toast- ers, in any locations including the internal or external trim, seats and deck. ●Do not use any electrical appliances, which are easily affected by vibration

or heat, inside the vehicle. Vibration while driving, or the heat of the sun while parking, may result in damage to those electrical appliances.

■If any electrical appliances are to be used while driving

Securely fasten both the appliances and their cables to prevent them from falling or getting caught any of the power train components.