2015 Toyota Camry Owners Manual

indicated on the tire sidewall.

17  7 J, 17  4 T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

P225/45R18 91V, T155/70D17 110M Driving under normal conditions

Front: 33 psi (230 kPa, 2.3 kgf/cm2 or bar) Rear: 33 psi (230 kPa, 2.3 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar)

Driving at high speeds (above 100 mph [160
km/h]) (in countries where such speeds are permitted by law)

Add 6 psi (40 kPa, 0.4 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.

Wheel size Wheel nut torque

18  7.5 J, 17  4 T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

CAMRY_U (OM33A86U)

508

9-1. Specifications

Light bulbs*1

Light bulbs

Bulb No.

W5W

7444NA

 9005

side marker

Headlights Low beam (halogen bulbs)*2
High beam (halogen bulbs)*2
Front lights Front turn signal/ parking lights (bulb type)*2
Rear turn signal lights WY21W Stop/tail/rear side maker lights License plate lights Back-up lights Front interior/ personal lights*2
Rear interior/ personal lights*2
Interior light*2
Door courtesy lights Vanity lights*2
Trunk light

 168
 194

W5W 921

7443





Exterior

Interior

55
60

28/8

21

21/5

16

3.8

Type

A: H11 halogen bulbs C: Wedge base bulbs (clear) E: Double end bulbs *1: Light bulbs not listed in this table are LED bulbs. *2: If equipped

B: HB3 halogen bulbs D: Wedge base bulbs (amber)

CAMRY_U (OM33A86U)

9-1. Specifications

509

Fuel information

You must only use unleaded gasoline in your vehicle. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87
may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A..

■Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your vehicle has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

■Gasoline quality

In very few cases, driveability problems may be caused by the brand of gaso- line you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

■Gasoline quality standards

●Automotive manufacturers in the U.S.A., Europe and Japan have developed a specification for fuel quality called the World-Wide Fuel Charter (WWFC), which is expected to be applied worldwide.

●The WWFC consists of four categories that are based on required emission

levels. In the U.S., category 4 has been adopted.

●The WWFC improves air quality by lowering emissions in vehicle fleets, and

improves customer satisfaction through better performance.

■Recommendation of the use of gasoline containing detergent additives ●Toyota recommends the use of gasoline that contains detergent additives to

avoid the build-up of engine deposits.

●All gasoline sold in the U.S.A. contains minimum detergent additives to clean and/or keep clean intake systems, per EPA's lowest additives concen- tration program.

●Toyota strongly recommends the use of Top Tier Detergent Gasoline. For more information on Top Tier Detergent Gasoline and a list of marketers, please go to the official website www.toptiergas.com.

CAMRY_U (OM33A86U)

510

9-1. Specifications

■Recommendation of the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

■Non-recommendation of the use of blended gasoline

●Use only gasoline containing up to 15%

ethanol. DO NOT use any flex-fuel or gasoline that could contain more than 15% etha- nol, including from any pump labeled E30, E50, E85 (which are only some examples of fuel containing more than 15% ethanol).

DO NOT use gasoline contain- ing more than 15% ethanol.

(30% ethanol)

(50% ethanol)

(85% ethanol)

●If you use gasohol in your vehicle, be sure that it has an octane rating no

lower than 87.

●Toyota does not recommend the use of gasoline containing methanol.

■Non-recommendation of the use of gasoline containing MMT

Some gasoline contains an octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

■If your engine knocks

●Consult your Toyota dealer. ●You may occasionally notice light knocking for a short time while accelerat-

ing or driving uphill. This is normal and there is no need for concern.

CAMRY_U (OM33A86U)

9-1. Specifications

511

NOTICE

■Notice on fuel quality

●Do not use improper fuels. If improper fuels are used, the engine will be

damaged.

●Do not use leaded gasoline.

Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.

●Do not use gasohol other than the type previously stated.

Other gasohol may cause fuel system damage or vehicle performance problems.

●Using unleaded gasoline with an octane number or rating lower than the

level previously stated will cause persistent heavy knocking. At worst, this will lead to engine damage.

■Fuel-related poor driveability

If poor driveability is encountered after using a different type of fuel (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

■When refueling with gasohol

Take care not to spill gasohol. It can damage your vehicle’s paint.

CAMRY_U (OM33A86U)

512

9-1. Specifications

Tire information

Typical tire symbols

 Full-size tire

 Compact spare tire

CAMRY_U (OM33A86U)

9-1. Specifications

513

10

11

Tire size (P. 515) DOT and Tire Identification Number (TIN)(P. 514) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators(P. 403) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly put into the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure. Load limit at maximum cold tire inflation pressure (P. 519) Maximum cold tire inflation pressure (P. 519) This means the pressure to which a tire may be inflated. Summer tires or all season tires (P. 407) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. “TEMPORARY USE ONLY” A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded on its sidewall. This tire is designed for temporary emergency use only.

CAMRY_U (OM33A86U)

514

9-1. Specifications

Typical DOT and Tire Identification Number (TIN)

DOT symbol* Tire Identification Number (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional type code (3 or 4 letters) Manufacturing week Manufacturing year

tire

*: The DOT symbol certifies that the tire conforms to applicable Federal

Motor Vehicle Safety Standards.

CAMRY_U (OM33A86U)

9-1. Specifications

515

Tire size ■ Typical tire size information

The illustration indicates typical tire size.

Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol (alphabet with one letter)

■ Tire dimensions Section width Tire height Wheel diameter

CAMRY_U (OM33A86U)

516

9-1. Specifications

Tire section names

10

11

Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer

CAMRY_U (OM33A86U)

9-1. Specifications

517

Uniform Tire Quality Grading This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.

Your Toyota dealer will help answer any questions you may have as you read this information.

■ DOT quality grades

All passenger vehicle tires must conform to Federal Safety Require- ments in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.

For example: Treadwear 200 Traction AA Temperature A

■ Treadwear

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course.

For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use. Performance may differ significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

■ Traction AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.

A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turn- ing) traction.

CAMRY_U (OM33A86U)

518

9-1. Specifications

■ Temperature A, B, C

The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel.

Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. Grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Stan- dard No. 109. Grades B and A represent higher levels of performance on the labo- ratory test wheel than the minimum required by law. Warning: The temperature grades of a tire assume that it is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire failure.

CAMRY_U (OM33A86U)

9-1. Specifications

519

Glossary of tire terminology

Tire related term

Meaning

Cold tire inflation pres- sure

Maximum pressure

inflation

Recommended tion pressure

infla-

Accessory weight

Curb weight

Maximum loaded vehi- cle weight

Normal weight

occupant

Occupant distribution

Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer The combined weight (in excess of those stan- dard items which may be replaced) of auto- matic transmission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory-installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight 150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows Distribution of occupants in a vehicle as speci- fied in the third column of Table 1* below

CAMRY_U (OM33A86U)

520

9-1. Specifications

Tire related term

Meaning

Production weight

options

Rim

Rim diameter (Wheel diameter) Rim size designation

Rim type designation

Rim width Vehicle weight capacity)

capacity load

(Total

Vehicle maximum load on the tire

Vehicle normal load on the tire

Weather side

Bead

Bead separation

The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated

Nominal diameter of the bead seat

Rim diameter and width The industry manufacturer’s designation for a rim by style or code Nominal distance between rim flanges The rated cargo and luggage load plus 150 lb. (68 kg) times the vehicle’s designated seating capacity The load on an individual tire that is deter- mined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two The load on an individual tire that is deter- mined by distributing to each axle its share of curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1* below), and dividing by two The surface area of the rim not covered by the inflated tire The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between compo- nents in the bead

CAMRY_U (OM33A86U)

Tire related term

Meaning

9-1. Specifications

521

Bias ply tire

Carcass

Chunking

Cord

Cord separation

Cracking

CT

Extra load tire

Groove

Innerliner

Innerliner separation

Intended sidewall

outboard

A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall rubber which, when inflated, bears the load The breaking away of pieces of the tread or sidewall The strands forming the plies in the tire The parting of cords from adjacent rubber compounds Any parting within the tread, sidewall, or inner- liner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The space between two adjacent tread ribs The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire The parting of the innerliner from cord material in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (b) The outward facing sidewall of an asym- metrical tire that has a particular side that must always face outward when mounted on a vehicle

CAMRY_U (OM33A86U)

522

9-1. Specifications

Tire related term

Meaning

Light truck (LT) tire

Load rating

Maximum load rating

Maximum permissible inflation pressure

Measuring rim

Open splice

Outer diameter

Overall width

Passenger car tire

Ply

Ply separation

Pneumatic tire

Radial ply tire

Reinforced tire

A tire designated by its manufacturer as pri- marily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry for a given inflation pressure The load rating for a tire at the maximum per- missible inflation pressure for that tire The maximum cold inflation pressure to which a tire may be inflated The rim on which a tire is fitted for physical dimension requirements Any parting at any junction of tread, sidewall, or innerliner that extends to cord material The overall diameter of an inflated new tire The linear distance between the exteriors of the sidewalls of an inflated tire, including ele- vations due to labeling, decorations, or protec- tive bands or ribs A tire intended for use on passenger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less. A layer of rubber-coated parallel cords A parting of rubber compound between adja- cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90
degrees to the centerline of the tread A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire

CAMRY_U (OM33A86U)

Tire related term

Meaning

9-1. Specifications

523

Section width

Sidewall

Sidewall separation

Snow tire

Test rim

Tread

Tread rib

Tread separation

Treadwear (TWI)

indicators

Wheel-holding fixture

The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and bead The parting of the rubber compound from the cord material in the sidewall A tire that attains a traction index equal to or greater than 110, compared to the ASTM E- 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( on at least one sidewall The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire That portion of a tire that comes into contact with the road around a tire Pulling away of the tread from the tire carcass The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread The fixture used to hold the wheel and tire assembly securely during testing

tread section running circumferentially

*: Table 1  Occupant loading and distribution for vehicle normal load for

various designated seating capacities

CAMRY_U (OM33A86U)

524

9-1. Specifications

Designated seating capacity, Number of

occupants 2 through 4

5 through 10

11 through 15

16 through 20

Vehicle normal load, Number of occupants

Occupant distribution in a normally loaded

vehicle 2 in front

2 in front, 1 in second

seat

2 in front, 1 in second seat, 1 in third seat, 1

in fourth seat

2 in front, 2 in second seat, 2 in third seat, 1

in fourth seat

CAMRY_U (OM33A86U)

9-2. Customization

525

Customizable features

Your vehicle includes a variety of electronic features that can be personalized to suit your preferences. The settings of these fea- tures can be changed by using the meter control switches, the audio system screen or at your Toyota dealer.

Customizing vehicle features ■ Changing by using the Entune Audio system*1

Press the “SETUP” button. Select “Vehicle” on the “Setup” screen.

Various setting can be changed. Refer to the list of settings that can be changed for details.

■ Changing by using the Entune Audio Plus system*2 or Entune

Premium Audio with Navigation system*2

Press the “APPS” button. Select “Setup” on the “Apps” screen and select “Vehicle”.

Various setting can be changed. Refer to the list of settings that can be changed for details.

*1: Audio system with “CAR” button *2: Audio system with “APPS” button

CAMRY_U (OM33A86U)

526

9-2. Customization

Customizable features Some function settings are changed simultaneously with other func- tions being customized. Contact your Toyota dealer for further details. Definition of symbols: O = Available, —=Not available ■ Gauges, meters and multi-information display (P. 77, 83)

 Vehicles without a multi-information display

Settings that can be changed on the Entune Audio system screen Settings that can be changed by display change button Settings that can be changed by your Toyota dealer

Function*1

Default setting

Customized set-

ting

Indicator

Eco Driving Light  Vehicles with a multi-information display

(Self-lighting)

On

Off

— O O

Settings that can be changed on the Entune Audio system screen Settings that can be changed by the meter control switches Settings that can be changed by your Toyota dealer

Function*1

Default setting

Customized set-

ting

O O —

O O —

— O —

French Spanish km (km/L)

km (L/100 km) miles (MPG

CAN) °C On

(Self-lighting) — O —

Language*2

English

Units*2

miles (MPG US)

Eco Driving Light

Indicator

°F

Off

CAMRY_U (OM33A86U)

9-2. Customization

527

Customized set-

ting

— O —

6 of the following

items: P. 85

— O —

Function*1

Drive information 1

Drive information 2

Drive information 3

Default setting

Digital speedom-

eter

Distance to

empty

Average fuel economy (after

reset)

Current fuel economy

Trip distance (after reset)

Trip elapsed time

— O —

— O —

O O —

— O O

— O —

Pop-up display

On

Accent color

Light blue

Off Blue Orange Yellow

Speed limit display*3

On with the

speed limit cau- tion indicator (yellow) enabled

Maintenance system ini- tialization*4

Off

On with the

speed limit cau- tion indicator (yellow) not

enabled

Off

On

*1: For details about each function: P. 86
*2: The default setting varies according to country. *3: Speed limit display may not be available for some regions. *4: U.S.A. only

CAMRY_U (OM33A86U)

528

9-2. Customization

Settings that can be changed using the Entune Audio system Settings that can be changed using the Entune Audio Plus system or Entune Premium Audio with Navigation system Settings that can be changed by your Toyota dealer Definition of symbols: O = Available, — = Not available ■ Door lock (P. 101, 109, 487)

Function

Default setting

Customized set-

ting

Unlocking using a key

Driver's door

unlocked in one step, all doors unlocked in two

steps

All doors

unlocked in one

step.

Automatic door lock

Shifting the shift lever to position

other than P

Automatic door unlock

Shifting the shift

lever to P

Off

Vehicle speed reaches a cer-

tain level.

Off

Driver’s door is

opened

— O O

O O O

O O O

Locking/unlocking of the trunk when all doors are locked/unlocked

On

Off

— — O

CAMRY_U (OM33A86U)

■ Smart key system* and wireless remote control (P. 101, 109)

9-2. Customization

529

Function

Default setting

Customized set-

ting

On

On

Level 5

Operation signal (Emergency flashers) Operation signal (Buzzer) Operation buzzer vol- ume Time elapsed before automatic lock function is activated if door is not opened after being unlocked Open buzzer *: If equipped ■ Smart key system* (P. 101, 109, 114)

door warning

60 seconds

door

On

— O O

— — O

Off

Off

Off to level 7

O O O

Off

30 seconds

— O O

120 seconds

Off

— — O

Function

Default setting

Smart key system Number of permissible times continuous of smart lock *: If equipped

On

Twice

Customized set-

ting Off

— — O

Unlimited

— — O

CAMRY_U (OM33A86U)

530

9-2. Customization

■ Wireless remote control (P. 94, 101, 109)

Function

Default setting

Wireless remote control

On

Customized set-

ting Off

Unlocking operation

Driver’s door unlocked in one step, all doors unlocked in two

steps

Trunk unlocking opera- tion

Press and hold

(short)

All doors

unlocked in one

step

One short press

Push twice

Press and hold

— — O

O O O

— — O

(long) Off Off

— — O Panic function ■ Power window (driver’s door) and moon roof* (P. 133, 136)

On

Function

Default setting

Key linked operation Wireless remote control linked opening Key linked closing Wireless remote control linked opening buzzer *: If equipped ■ Moon roof* (P. 136)

Off

Off

Off

On

Customized set-

ting On

On

On

Off

— — O

— — O

— — O

— — O

Function

Default setting

Customized set-

ting

Linked operation of com- ponents when door key is used Linked operation of com- ponents when wireless remote control is used *: If equipped

Slide only

Tilt only

— — O

Slide only

Tilt only

— — O

CAMRY_U (OM33A86U)

■ Turn signal lever (P. 166)

Function

Default setting

The number of times the turn signal lights flash automatically when the turn is moved to the first posi- tion lane change*1

during

signal

lever

9-2. Customization

531

Customized set-

ting Off*2

4 to 7

— — O

*1: After flashing the turn signal lights when turning left or right while this func- tion is off and the turn signal lever is moved to the first position in the direc- tion of the flashing light, the turn signal lights can be selected to be flashing or off.

*2: The turn signal lights will be off if the turn signal lever is moved to the first

position in the direction of flashing light.

■ Automatic light control system* (P. 168)

Function

Default setting

Customized set-

ting

Light sensor sensitivity Time elapsed before headlights automatically turn off after doors are closed *: If equipped ■ Lights (P. 168, 172)

Level 3

Level 1 to 5

O O O

30 seconds

Off

60 seconds 90 seconds

O O O

Function

Default setting

Customized set-

ting

running

Daytime light system (except Canada) Automatic high beam*

On

On

Off

Off

O O O

— O O

CAMRY_U (OM33A86U)

532

9-2. Customization

■ Automatic air conditioning system* (P. 331)

Function

Default setting

Customized set-

ting

A/C auto switch opera- tion *: If equipped ■ Illumination (P. 339)

Auto

Manual

— O O

Function

Default setting

Time elapsed before lights turn off

15 seconds

to

the

Operation when doors are unlocked Vehicles without smart key system: Operation after the engine switch turned the “LOCK” position Vehicles with smart key system: Operation after the engine switch turned off Operation when you approach the vehicle with the electronic key on your person* *: Vehicles with a smart key system ■ Seat belt reminder (P. 448)

On

On

On

Customized set-

ting

7.5 seconds 30 seconds

O O O

Off

— — O

Off

— — O

Off

— — O

Function

Default setting

Customized set-

ting

Vehicle speed seat buzzer

belt

linked reminder

On

Off

— — O

CAMRY_U (OM33A86U)

9-2. Customization

533

WARNING

■During customization

As the engine needs to be running during customization, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust gases including harmful carbon monoxide (CO) may collect and enter the vehicle. This may lead to death or a serious health hazard.

NOTICE

■During customization

To prevent battery discharge, ensure that the engine is running while cus- tomizing features.

CAMRY_U (OM33A86U)

534

9-3. Items to initialize

Items to initialize The following items must be initialized for normal system opera- tion after such cases as maintenance being performed on the vehicle:

Item

When to initialize

Reference

light

required Maintenance (vehicles reminder without a multi-information display) or message indicat- ing maintenance is required (vehicles with a multi-infor- mation display) (U.S.A. only)

Tire pressure warning sys- tem

After the maintenance is per- formed

P. 381

When changing the tire infla- tion pressure by changing trav- eling speed or load weight, etc.

P. 405

CAMRY_U (OM33A86U)

535

For owners

10

Reporting safety defects for U.S. owners........................ 536
Seat belt instructions for Canadian owners (in French) ............................... 537
SRS airbag instructions for Canadian owners (in French) ............................... 539

CAMRY_U (OM33A86U)

536

Reporting safety defects for U.S. owners

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addi- tion to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800- 331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 to http:// www.safercar.gov ; or write to: Administrator, NHTSA, 1200 New Jersey Ave, S.E., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

(TTY: 1-800-424-9153); go

CAMRY_U (OM33A86U)

537

Seat belt instructions for Canadian owners (in French)

The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.

Utilisation correcte des ceintures de sécurité ● Déroulez la sangle diagonale de telle sorte qu'elle passe bien sur l'épaule, sans pour autant être en contact avec le cou ou glisser de l'épaule.

● Placez la sangle abdominale le plus bas possible sur les han- ches.

● Réglez la position du dossier de siège. Asseyez-vous le dos droit et

calez-vous bien dans le siège.

● Ne vrillez pas la ceinture de sécurité.

Entretien et soin ■ Ceintures de sécurité

Nettoyez avec un chiffon ou une éponge humectée d’eau savon- neuse tiède. Vérifiez régulièrement que les ceintures ne sont pas effilochées, entaillées ou exagérément usées.

10

CAMRY_U (OM33A86U)

538

AVERTISSEMENT

■Dommage et usure de la ceinture de sécurité

Inspectez la ceinture de sécurité périodiquement. Vérifiez si elles ne sont pas entaillées, effilochées et que leurs ancrages ne sont pas desserrés. N’utilisez pas une ceinture de sécurité défectueuse avant qu’elle ne soit remplacée. Une ceinture de sécurité défectueuse n’apporte aucune garan- tie de protection de l’occupant en cas de blessures graves, voire mortelles.

CAMRY_U (OM33A86U)

539

SRS airbag instructions for Canadian owners (in French)

The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English.

◆ Coussins gonflables frontaux SRS

Coussin gonflable conducteur/coussin gonflable du passager avant SRS Participent à la protection de la tête et du thorax du conducteur et du passager avant contre les chocs contre les éléments de l'habitacle Coussins gonflables de genoux SRS Participent à la protection du conducteur et du passager avant

10

CAMRY_U (OM33A86U)

540

◆ Coussins gonflables latéraux et rideaux SRS

Coussins gonflables latéraux avant SRS Participent à la protection du torse des occupants de siège avant Coussins gonflables latéraux arrière SRS Participent à la protection du torse des occupants des sièges latéraux arrière Coussins gonflables rideaux SRS ● Participent principalement à la protection de la tête des occu-

pants des sièges latéraux

● Peut contribuer à empêcher les occupants d’être éjectés du

véhicule en cas de tonneau

CAMRY_U (OM33A86U)

Composants du système de coussins gonflables SRS

541