2006 Toyota Camry Owners Manual

can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

With a spare tire of the same wheel type as the installed tires

With a spare tire of different wheel type from the installed tires

319

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

CAUTION

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

Manual

To equalize the wear and help ex- tend tire life, Toyota recommends that you rotate your tires accord- ing to the maintenance schedule. (For scheduled maintenance infor- mation, please refer to the “Sched- uled Maintenance Guide” or “Own- er’s Supplement”.) However, the most appropriate tim- ing for tire rotation may vary ac- cording to your driving habits and road surface conditions. See “If you have a flat tire” on page 268 in Section 4 for tire change proce- dure. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking.

320

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.

CAUTION

Do not use snow tires other than the manufacturer’s recommended size, as this may cause dangerous handling characteristics resulting loss of control. Otherwise, an accident may occur resulting in death or serious injuries.

in

2006 CAMRY from July ‘05 Prod. (OM33708U)

SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.

CAUTION

For P215/60R16 and P215/55R17 use the following type chains.

tires,

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size. For P205/65R15 tires, use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains.

A Diameter of side chain B Width of side chain C Length of side chain D Diameter of cross chain E Width of cross chain F Length of cross chain

mm (in.) 3 (0.12) 10 (0.39) 30 (1.18) 4 (0.16) 14 (0.55) 25 (0.98)

’06Camry_U (L/O 0507)

Side chain

Regulations regarding the use of tire chains vary according to location or type of road, so always check local reg- ulations before installing chains.

NOTICE

Cross chain

If the wrong combination of tire and chain is used, the chains could dam- age the vehicle body.

the

rear driving

CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.

0.5—1.0

321

2006 CAMRY from July ‘05 Prod. (OM33708U)

CAUTION

D Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

D When driving with chains installed, to drive carefully. Slow be sure down before entering curves to avoid losing control of the vehicle. Otherwise an accident may occur.

NOTICE

Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.

322

’06Camry_U (L/O 0507)

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace a damaged wheel, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

CAUTION

Do not use wheels other than the manufacturer’s recommended size, as this may cause dangerous handling characteristics resulting loss of control. Otherwise, an accident may occur resulting in death or serious injuries.

in

2006 CAMRY from July ‘05 Prod. (OM33708U)

Aluminum wheel precautions D When aluminum wheels, check tight after driving your vehicle the first 1600
km (1000 miles).

the wheel nuts are

installing that

repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

D When using tire chains, be careful not

to damage the aluminum wheels.

D Use only Toyota wheel nuts and for your aluminum

wrench designed wheels.

D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

’06Camry_U (L/O 0507)

323

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

325
326
327
328
328

324

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

EMERGENCY MEASURES D If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

—Checking battery exterior

Terminals

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

325

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

—Checking battery condition

NOTICE

Type A

z Be sure the engine and all accesso- ries are off before performing main- tenance.

z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

If the battery is disconnected or run down, the moon roof may not operate automatically and the jam protection func- tion will not function correctly after you reconnect, replace or recharge the battery. In any of these cases, you should normal- ize the moon roof. To normalize the moon roof, see “Electric moon roof” on page 35
in Section 1−2.

326

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY INDICATOR Check the battery condition by the indi- cator color.

Indicator color

Type A

Type B

Green

Blue

Dark

White

Clear or

light yellow

Red

Condition

Good

Charging necessary. Have battery checked by your Toyota dealer. Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Checking and replacing fuses

Type A

Good

Blown

Type B

Good

Blown

Type C

Good

Blown

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” on page 303 in Sec- tion 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull the suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 342 in Section 8 for the functions controlled by each circuit.

Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “MIR HTR” or fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close to the rating as possible. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

“POWER POINT”

that specified,

lower

than

the

327

2006 CAMRY from July ‘05 Prod. (OM33708U)

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible. You should normalize the moon roof if it does not operate automatically or the jam protection function does not operate cor- rectly after fuses. To normalize the moon roof, see “Electric moon roof” on page 35 in Section 1−2.

replacing blown

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

328

’06Camry_U (L/O 0507)

Adding washer fluid If any washer does not work or the low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. However, in cold areas where tempera- tures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

D To prevent burning yourself, do not replace the light bulbs while they are hot.

D Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

W Type

Light bulbs

the

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the is caused by fogging temperature difference between the outside and the windshield fogs up in the rain. However, if there large drop of water on the inside of the lens, or if there is water pooled light, contact your Toyota dealer.

inside of

inside

lens,

is a

just

like

the

the

Light bulbs

Headlights (high)

Headlights (low)

Parking and front side marker lights Front turn signal lights (type A) Front turn signal lights (type B) Rear turn signal lights (type A) Rear turn signal lights (type B) Stop/tail and rear side marker lights (type A) Stop/tail and rear side marker lights (type B)

Tail lights

Back−up lights

Front fog lights

Bulb No. 9005

9006

—

60

51

4157

27

—

21

4157

27

—

21

3157

27/8

— 21/5

—

921

9006

18

51

License plate lights

—

High mounted stoplight Personal lights

Interior light (type A) Interior light (type B) Vanity lights

Glove box light

Trunk light (type A)

Trunk light (type B)

Bulb No.

921

—

—

—

—

—

—

—

W Type

18

4.9

1.4

A: HB3 halogen bulbs B: HB4 halogen bulbs C: Wedge base bulbs (clear) D: Wedge base bulbs (amber) E: Double end bulbs

329

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

—Headlights

High beam (inside)

Low beam (outside)

1. Open the hood. Turn the bulb base counterclockwise to the front of the vehicle as shown.

The above illustration shows the left−hand headlight.

2. Unplug the connector while depress-

ing the lock release.

If the connector is tight, wiggle it.

3. Plug in a new bulb into the connec- tor and install it into the mounting hole. is not necessary after replacing Aiming the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

330

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

—Parking and front side marker lights

—Front turn signal lights

—Rear turn signal, stop/tail and rear side marker, tail and back−up lights

331

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

—High mounted stoplight

a: Rear turn signal light b: Stop/tail and rear side marker light c: Tail light d: Back−up light

332

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

—Front fog and license plate lights If either the left or right front fog or license plate lights burns out, contact your Toyota dealer.

NOTICE

Do not try to replace the front fog or license plate light bulbs by yourself. You may damage the vehicle.

333

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

SECTION 8

SPECIFICATIONS Specifications Dimensions and weights Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

336
336
337
337
340
342

335

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Dimensions and weights

Overall length

Overall width

Overall height∗1

Wheelbase

Front tread

Rear tread

Vehicle capacity weight (occupants + luggage)

Towing capacity (trailer weight + cargo weight) ∗1: Unladen vehicle ∗2: With P205/65R15 tires ∗3: With P215/60R16 and P215/55R17 tires

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

kg (lb.)

kg (lb.)

4805 (189.2)

1795

1490
1500

(70.7) (58.7)∗2
(59.1)∗3

2720 (107.1)

1545

(60.8)

1535

(60.4)

410

(900)

907 (2000)

Engine Model:

2AZ−FE, 1MZ−FE and 3MZ−FE

Type:

2AZ−FE engine

4 cylinder in line, 4 cycle, gasoline

1MZ−FE and 3MZ−FE engines

6 cylinder V type, 4 cycle, gasoline

Bore and stroke, mm (in.):

2AZ−FE engine

88.5 96.0 (3.48 3.78)

1MZ−FE engine

87.5 83.0 (3.44 3.27)

3MZ−FE engine

92.0 83.0 (3.62 3.27)

Displacement, cm3 (cu. in.):

2AZ−FE engine 1MZ−FE engine 3MZ−FE engine

2362 (144.1) 2995 (182.8) 3311 (202.1)

336

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Fuel Fuel type:

2.4 L 4−cylinder (2AZ−FE) engine

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

3.0 L V6 (1MZ−FE) and 3.3 L V6 (3MZ− FE) engines

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher. For improved vehicle perfor- mance, use premium unleaded gaso- line with an Octane Rating of 91 (Re- search Octane Number 96) or higher.

Fuel tank capacity, L (gal., Imp. gal.):

70 (18.5, 15.4)

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

2.4 L 4−cylinder (2AZ−FE) engine

Intake Exhaust

0.19—0.29 (0.007—0.011) 0.30—0.40 (0.012—0.016) 3.0 L V6 (1MZ−FE) and 3.3 L V6 (3MZ− FE) engines

Intake Exhaust

0.15—0.25 (0.006—0.010) 0.25—0.35 (0.010—0.014)

Spark plug type:

DENSO NGK

SK20R11
IFR6A11

Spark plug gap, mm(in.):

1.1 (0.043)

3.0 L V6 (1MZ−FE) and 3.3 L V6 (3MZ− FE) engines— Drive Borroughs No.BT−33−73F (used belt), Ibf:

tension measured with gauge

tension

drive

belt

belt

125"10

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):

2.4 L 4−cylinder (2AZ−FE) engine

With filter Without filter

3.8 (4.0, 3.3) 3.6 (3.8, 3.2) 3.0 L V6 (1MZ−FE) and 3.3 L V6 (3MZ− FE) engines With filter Without filter

4.7 (5.0, 4.1) 4.5 (4.8, 4.0) “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

is used

satisfy

the

ILSAC multigrade engine oil

337

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Recommended oil viscosity:

SAE 5W−30

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

BATTERY Open voltage∗ at 20_C (68_F):

2.4 L 4−cylinder (2AZ−FE) engine

6.2 (6.6, 5.4) 3.0 L V6 (1MZ−FE) and 3.3 L V6 (3MZ− FE) engines

9.2 (9.8, 8.1)

Coolant type:

“Toyota Super Long Life Coolant” is used in your Toyota vehicle at factory fill. In order to avoid technical problems, only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. (Coolant with long−life hybrid organic acid technology is a combination of low phosphates and organic acids.) Do not use plain water alone. Please contact your Toyota dealer for further details.

Outside temperature

Please contact your Toyota dealer for fur- ther details.

338

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

Fully charged Half charged Discharged

∗: Voltage that is checked 20 minutes af- ter the key is removed with all the lights turned off Charging rates:

5 A max.

Note: If replacement is necessary, make sure to do so with a battery that meets the same standard as the original. CLUTCH Pedal free play, mm (in.):

5—15 (0.2—0.6)

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

MANUAL TRANSAXLE Oil capacity, L (qt., Imp. qt.):

2.5 (2.6, 2.2)

Oil type:

Gear oil API GL−4 or GL−5

Recommended oil viscosity:

SAE 75W−90

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

AUTOMATIC TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.):

3.5 (3.7, 3.1)

Fluid type:

Toyota Genuine ATF Type T−IV

in

listed

Guide”

is necessary

Change automatic transmission fluid only as necessary. Generally, to change it automatic transmission fluid only if your vehicle is driven under one of the Special Operating Conditions your “Scheduled Maintenance or “Owner’s Manual Supplement”. When changing the automatic transmission fluid, use only “Toyota Genuine ATF Type T−IV” (ATF JWS3309 or NWS6500) in to aid assuring optimum transaxle performance. Notice: Using automatic transmission fluid other than “Toyota Genuine ATF Type T−IV” may cause deterioration in shift quality, locking up of your trans- mission accompanied by vibration, and ultimately damage the automatic trans- mission of your vehicle. Please contact your Toyota dealer for fur- ther details.

BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.):

63 (2.5)∗

∗: Fixed type and adjustable type (in front most position) Pedal free play, mm (in.):

Fixed type Adjustable type (in front most position)

1—6 (0.04—0.24)

1—8 (0.04—0.31)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake Lever type—

Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44
lbf):

6—9 clicks

Pedal type—

Parking brake adjustment when de- pressed with the force of 300 N (31
kgf, 67 lbf): 3—6 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRONrII or III

339

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Tires Tire size and cold tire inflation pressure: Front and rear Normal driving

kPa (kgf/cm2 or bar, psi)

Grade

LE

XLE

2.4 L SE

Tire size

Front

Rear

Wheel size

P205/65R15 92T P205/65R15 92H

200 (2.0, 29)

200 (2.0, 29)

15 6 1/2 JJ

P215/60R16 94V

200 (2.0, 29)

200 (2.0, 29)

16 6 1/2 JJ

3.3 L V6 SE

P215/55R17 93V

210 (2.1, 30)

210 (2.1, 30)

17 7 JJ

When driving under the above vehicle conditions at sustained high speeds above 160 km/h (100 mph), in countries where such speeds are permitted by−law, inflate the front and rear tires to 240 kPa (2.4 kgf/cm2 or bar, 35 psi) provided that it does not exceed the maximum cold tire inflation pressure molded on the tire sidewall. Trailer driving

kPa (kgf/cm2 or bar, psi)

Grade

LE

XLE

2.4 L SE

Tire size

P205/65R15 92T P205/65R15 92H

Front

Rear

220 (2.2, 32)

220 (2.2, 32)

P215/60R16 94V

200 (2.0, 29)

200 (2.0, 29)

3.3 L V6 SE

P215/55R17 93V

220 (2.2, 32)

220 (2.2, 32)

340

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Spare

kPa (kgf/cm2 or bar, psi)

Tire size

Front

Rear

T145/80R16 105M

420 (4.2, 60)

420 (4.2, 60)

Wheel size 16 4T

Wheel nut torque, N·m (kgf·m, ft·lbf):

103 (10.5, 76)

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pres-

sure” through “Aluminum wheel precautions”, pages 314 through 323, in Section 7−2.

341

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Fuses

Engine compartment

342

Instrument panel

Fuses (type A) 1. HEAD LH LWR 15 A: Left−hand head-

light (low beam)

2. HEAD RH LWR 15 A: Right−hand

headlight (low beam)

3. DRL 5 A: Daytime running light system 4. A/C 10 A: Air conditioning system 5. SPARE 10 A: Spare fuse 6. SPARE 15 A: Spare fuse 7. SPARE 5 A: Spare fuse 8. AM2 30 A: Starting system, “IGN” and

“IG2” fuses

9. HEAD LH UPR 10 A: Left−hand head-

light (high beam)

10. HEAD RH UPR 10 A: Right−hand

headlight (high beam)

11. ST 5 A: Multiport fuel injection system/ sequential multiport fuel injection sys- tem

12. TEL 5 A: No circuit 13. ALT−S 5 A: Charging system 14. IGN 15 A: Starting system 15. IG2 10 A: Multiport fuel injection sys- tem/sequential multiport injection system, SRS airbag system, front seat belt pretensioners, cruise control sys- tem

fuel

16. DOOR1 25 A: Multiplex communication system (power door lock system, auto− door locking system, wireless remote control system)

17. EFI 20 A: Multiport fuel injection sys- injection

tem/sequential multiport system

fuel

18. HORN 10 A: Horns 19. D.C.C 30 A: “ECU−B”, “RAD NO.1”

and “DOME” fuses

20. A/F 25 A: Multiport fuel injection sys- injection

tem/sequential multiport system

fuel

2006 CAMRY from July ‘05 Prod. (OM33708U)

21. ETCS 10 A: Multiport

fuel

system/sequential multiport tion system

injection injec-

fuel

22. HAZ 15 A: Emergency flashers 23. ECU−B 10 A: Multiplex communication system (power door lock system, secu- rity system, auto−door locking system, automatic light control system, head- light delay off system, tail light auto cut system, illuminated entry system, daytime running light system, wireless remote control system), air conditioning system

light, personal lights,

24. DOME 7.5 A: Ignition switch light, inte- trunk light, rior vanity lights, garage door opener, clock, outside temperature display, mul- ti−information display

25. CIG 15 A: Cigarette lighter 26. ECU−ACC 5 A: Power rear view mir-

rors, clock, multi−information display

27. RAD NO.2 10 A: Audio system, navi-

gation system

28. POWER POINT 15 A: Power outlets 29. RAD NO.1 20 A: Audio system, navi-

gation system

’06Camry_U (L/O 0507)

30. GAUGE1 10 A: Gauges and meters, clock, outside temperature display, mul- ti−information display, shift lock system, seat belt reminder lights

31. ECU−IG 10 A: SRS airbag system, power windows, anti−lock brake system

32. WIPER 25 A: Windshield wipers 33. HTR 10 A: Air conditioning system 34. MIR HTR 10 A: Outside rear view mir-

ror heaters

35. AM1 5 A: Starting system 36. FOG 15 A: Front fog lights 37. SUN−SHADE 15 A: No circuit 38. GAUGE2 10 A: Auto anti−glare inside rear view mirror, compass, electric moon roof, back−up lights, automatic transmission indicator lights, automatic light control system, cruise control sys- tem

39. PANEL 10 A: Glove box light, clock, outside temperature display, multi−infor- cluster mation lights, lights, over- drive−off indicator light

instrument panel

instrument

display,

40. TAIL 10 A: Tail lights, parking lights,

license plate lights

41. PWR NO.4 20 A: Rear passenger’s

power window (left side)

42. PWR NO.2 20 A: Front passenger’s front passenger’s

lock system,

door power window

43. OBD 7.5 A: On−board diagnosis sys-

tem

44. SEAT HTR 20 A: Seat heaters 45. WASHER 15 A: Windshield washer 46. FAN RLY 10 A: Electric cooling fans 47. STOP 15 A: Stop lights, high mounted system,

brake

stoplight, anti−lock cruise control system

48. FUEL OPEN 5 A: No circuit 49. DOOR NO.2 25 A: Multiplex commu- nication system (power door lock sys- tem, auto−door locking system, wire- less remote control system)

50. AMP 25 A: No circuit 51. PWR NO.3 20 A: Rear passenger’s

power window (right side)

343

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

Fuses (type B) 52. MAIN 40 A: “HEAD LH LWR”, “HEAD RH LWR”, “HEAD LH UPR”, “HEAD LH UPR” and “DRL” fuses

53. ABS No.2 40 A: Anti−lock brake sys- tem, vehicle stability control system, traction control system, brake assist system

54. RDI 30 A: Electric cooling fan 55. CDS 30 A: Electric cooling fan 56. HTR 50 A: Air conditioning system 57. ADJ PDL 30 A: Power adjustable ped-

als

58. ABS No.3 30 A: Anti−lock brake sys- tem, vehicle stability control system, traction control system, brake assist system

59. PWR SEAT 30 A: Power seats 60. PWR NO.1 30 A: Driver’s door lock system, driver’s power window, electric moon roof

61. DEF 40 A: Rear window defogger

344

“PWR NO.3”,

Fuses (type C) 62. ALT 120 A: “DEF”, “PWR NO.1”, “PWR “PWR NO.4”, NO.2”, “STOP”, “DOOR NO.2”, “OBD”, “PWR SEAT”, “FUEL OPEN”, “FOG”, “AMP”, “CIG”, “PANEL”, NO.2”, “POWER “ECU−ACC”, “GAUGE2”, “ECU−IG”, “WIPER”, “WASHER”, “HTR” (10 A), “SEAT HTR” and “SUN−SHADE” fuses

“TAIL”, POINT”,

“AM1”, “RAD

“GAUGE1”,

63. ABS NO.1 50 A: Anti−lock brake sys- tem, vehicle stability control system, traction control system, brake assist system

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

SECTION 9

REPORTING SAFETY DEFECTS FOR U.S. OWNERS Reporting safety defects for U.S. owners Reporting safety defects for U.S. owners

. . . . . . . . . . . . . . . . . . . . . .

346

345

2006 CAMRY from July ‘05 Prod. (OM33708U)

’06Camry_U (L/O 0507)

To contact NHTSA, you may ei- ther call the Auto Safety Hotline toll−free at 1−800−424−9393 (or 366−0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hot- line.

Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately in- form the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll−free: 1−800−331−4331). If NHTSA receives similar com- plaints, it may open an investiga- tion, and if it finds that a safety defect exists in a group of ve- hicles, it may order a recall and remedy However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

campaign.

346

2006 CAMRY from July ‘05 Prod. (OM33708U)