2007 Toyota Camry HV Owners Manual

142

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Message

Status

Action

Steering lock is stuck.

Turn steering wheel slightly.

Oil change is nearly due.

Check engine oil.

Oil change is due.

Change engine oil.

Washer fluid level is low.

Add washer fluid.

Moon roof is opened with “POWER” switch turned off. Close moon roof.

Fuel door is left open.

Close the fuel door.

143

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(a)

(c)

(e)

This message is to warn the driver that the temperature for the inverter, trac- tion motor or motor generator is too high. Stop the vehicle and allow the the in- verter, traction motor and motor gener- ator to cool. See “If your vehicle over- heats” on page 317 in Section 4. the master The message appears with warning light and a warning tone sounds.

NOTICE

Do not continue driving with the mes- sage displayed.

This message is to warn the driver that the parking brake is not completely re- leased at the vehicle speed of 5 km/h (3 mph) or more. Stop the vehicle and release the park- ing brake fully. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the hybrid system is malfunctioning. If a malfunction of the hybrid system is detected, the message appears with the master warning tone when the “POWER” switch is on. If the message appears, stop the ve- hicle as soon as possible and contact a Toyota dealer.

light and warning

(b)

(d)

This message is to warn the driver that the engine oil pressure is too low. Turn the engine off as soon as possible and contact your Toyota dealer. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the engine coolant temperature is too high. Stop the vehicle and allow the engine to cool. See “If your vehicle overheats” on page 317 in Section 4. The message appears with the master warning light and a warning tone sounds.

NOTICE

Do not continue driving with an over- heated engine.

144

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(h)

(i)

(f)

This message is to remind the driver that any of the doors are opened. Close the door securely. The message appears with the master warning light and a warning tone sounds when the vehicle speed rises above 5
km/h (3 mph).

(g)

This message is to remind the driver that the trunk is opened. Close the trunk securely. the master The message appears with warning light a warning tone sounds when the vehicle speed rises above 5 km/h (3
mph).

This message is to warn the driver that the vehicle stability control (VSC) func- tion of the vehicle dynamics integrated management (VDIM) is malfunctioning. If the message appears, the functions of VDIM listed below may not work pro- perly. Have the vehicle checked by a Toyota dealer as soon as possible. However, as conventional braking oper- ates when applied, there is no problem to continue your driving. D Traction control function D Vehicle stability control function The message appears with the master warning light and a warning tone sounds. If the message appears together with the red brake system warning light, stop the vehicle immediately. For details, see “Ser- vice reminder indicators and warning buzz- ers” on page 150.

This message is to remind the driver that the transmission is not in the “P” position when starting the vehicle. If the message appears, put the trans- mission in the “P” position and push the “POWER” switch again. For the hy- brid system starting procedure, see “How to start the hybrid system” on page 301 in Section 3. The message appears with the master warning light and a warning tone sounds.

145

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(j)

(k)

(m)

in

the

following

This message is to warn of the hybrid battery condition. The message appears conditions.: D The hybrid battery voltage drops be- cause the transmission is left in the “N” position. If you put the transmission in the “P” position and the message disappears, the system is working properly.

This message is to warn the driver that the transmission is not in the “P” posi- tion when the driver’s door is opened. Put the transmission in the “P” posi- tion. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the transmission is not in the “P” posi- tion when leaving the vehicle. Put the transmission in the “P” posi- tion. The message appears with the master warning light and a warning tone sounds.

(l)

(n)

D The hybrid battery is discharged.

If the hybrid battery is discharged and the message appears along with the “READY” light turned on, stop your ve- hicle in a safe place and contact your Toyota dealer.

The message appears with the master warning light and a warning tone sounds.

This message is to remind the driver that the brake pedal is not depressed when starting the hybrid system. Depress the brake pedal firmly and press the “POWER” switch. For the starting pro- cedure, see “How to start the hybrid sys- tem” on page 301 in Section 3. If the brake pedal is not depressed, the message appears and a warning tone sounds when the hybrid system is started.

146

When this message appears in the fol- lowing cases, a warning tone sounds. D The key is not detected in the vehicle because someone has taken the key outside of the vehicle without turning the hybrid system off. At this time, a warning tone sounds. The above mes- sage turns off if the “POWER” switch is turned off or the key is in the ve- hicle.

D The key is not detected in the vehicle when the “POWER” switch is pushed. In this case, the above message ap- pears for 8 seconds.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(o)

(q)

(r)

This message is to warn the driver that the electronic key battery is low. Change the key battery as soon as pos- sible to ensure that the smart key sys- tem operates properly. The message appears with the master warning light and a warning tone sounds.

(p)

This message appears when the steer- ing lock is stuck. The message appears for 15 seconds. At this time, the green indicator light on the “POWER” switch flashes. To free the steering lock, rotate the steer- ing wheel slightly left or right while press- ing the “POWER” switch. the master The message appears with warning light and a warning tone sounds.

This message warns the driver that the steering lock function malfunctions. At this time, the amber indicator light on the “POWER” switch flashes. The hybrid system will not be turned on in this case. Contact your Toyota dealer as soon as possible. The message appears with the master warning light and a warning tone sounds.

This message is to remind the driver to change the engine oil. The message is a prior notice. Toyota recommends that the engine oil be changed as soon as possible. If the driving range after the previous oil change reaches 7200 km (4500 miles), the message appears for about 15 seconds with the master warning light and a warn- ing tone sounds. The engine oil maintenance data must be reset after the engine oil change. See following “Resetting the engine oil mainte- nance data”.

147

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(s)

This message is to remind the driver to change the engine oil. Change the engine oil as soon as pos- sible. If the driving range after the previous oil change reaches 8000 km (5000 miles), the message appears with the master warning tone sounds. The light and a warning message stays on with “POWER” switch set at ON. The engine oil maintenance data must be the engine oil change. See reset after “Resetting the engine oil maintenance data” below for the procedure to reset the system.

the

Resetting the engine oil maintenance data The engine oil maintenance data must be reset after replacement of the engine oil. Reset the data by the following procedure: 1. Turn off the hybrid system with the trip

meter A reading shown.

For details, see “—Odometer and two trip meters” on page 138 in this Section. 2. The “POWER” switch must be set at ON while holding down the trip meter reset knob. A message “OIL MILEAGE RESET MODE” will appear on the dis- play.

3. Hold down the knob at least 5 sec- onds. A message “COMPLETE” will ap- pear and the message “OIL MILEAGE RESET MODE” goes off.

(t)

This message appears when the washer fluid level becomes very low. Fill the tank as soon as possible. The message appears with warning light a warning tone sounds.

the master

(u)

is opened with

This message appears when the driver’s door the “POWER” switch turned off and the moon roof opened. When you leave your vehicle, be sure to close the moon roof. The message appears with the master warning light and a warning tone sounds.

148

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(v)

This message is to remind the driver that the fuel filler door is open. The message appears cases. 1. When you start

the vehicle with the

following

the

in

fuel door left open after refueling.

2. When you leave the fuel door open for more than 30 minutes during refueling. In case 1, stop the vehicle and close the fuel lid. In case 2, the internal valve in the fuel tank is closed. You must remove the fuel nozzle, tighten the fuel tank cap and close the fuel door. If is not completed you must refueling start refueling from the beginning.

CAUTION

Do not continue to refuel in case 2. Fuel may spray out of the fuel open- ing if you refuel the vehicle.

the master The message appears with warning light and a warning tone sounds.

149

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

or

(red indicator and buzzer)

(yellow indicator)

If parking brake is off, stop immediately and contact Toyota dealer.

Take vehicle to Toyota dealer. If red brake system warning light is also on, stop immediately and contact Toyota dealer.

(indicator and buzzer)

Fasten driver’s seat belt.

(indicator and buzzer)

Fasten front passenger’s seat belt.

Stop immediately and contact Toyota dealer.

or

Take vehicle to Toyota dealer.

Fill up tank.

(a)

(b)

(c)

(d)

(e)

(f)

150

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If the indicator or buzzer comes on...

Do this.

(g)

(h)

(i)

(j)

(k)

(l)

or

Take vehicle to Toyota dealer. If red brake system warning light is also on, stop immediately and contact Toyota deal- er.

Take vehicle to Toyota dealer.

(indicator and buzzer)

Close all doors and trunk lid.

Take vehicle to Toyota dealer immediately.

Adjust tire inflation pressure (including spare tire). If the light comes on after blinking for 1 minute, contact Toyota dealer.

Read a message on multi−information display.

(m)

Parking brake reminder buzzer

Release parking brake.

151

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

in

the

lights come on

(a) Brake System Warning Lights These following cases when the hybrid system is turned on. RED WARNING LIGHT D When the parking brake is applied... When the vehicle speed exceeds 5 km/h (3 mph), a message “PARK BRAKE” ap- pears on the multi−information display, the master warning light flashes and a warn- ing tone sounds. D When the brake fluid level is low...

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

YELLOW WARNING LIGHT D When the regenerative brake system or electronically controlled brake system fails...

When the yellow warning light comes on, the regenerative brake system and/or elec- tronically controlled brake system is mal- functioning. Take your vehicle to your Toyota dealer. RED AND YELLOW WARNING LIGHT D When fails...

the hydraulic brake system

If the red and yellow warning lights come on, it indicates a serious problem and you can continue driving no longer. Have your vehicle checked at your Toyota dealer in the following cases: D The red warning light does not come on even if the parking brake is applied when the hybrid system is on.

D The lights do not come on when the turned on with the

hybrid system parking brake released.

is

A red or yellow warning light turning on briefly during operation does not indicate a problem.

152

CAUTION

If any of the following conditions oc- curs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The red warning light does not turn off even after the parking brake is released with the hybrid system turned on.

D The red warning light stays on with

the hybrid system turned on.

In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop. D The red brake system warning light remains on together with the “ABS” warning light and “CHECK VSC SYSTEM” warning message.

In this case, not only the anti−lock brake system and vehicle stability control system will fail but also the vehicle will become extremely unsta- ble during braking.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

In the following case, drive directly to the nearest Toyota dealer. D The yellow warning light comes on

while driving.

Any of the following conditions may oc- cur, but do not indicate the malfunc- tion: D The red and yellow warning lights may stay on for about 60 seconds after the hybrid system is started. It is normal if it turns off after a while.

D Depressing the brake pedal repeatedly may turn on the red and yellow warn- ing lights. It is normal if the light turns off after a few seconds.

D The brake pedal stroke may be short is depressed

the brake pedal

when with the hybrid system off.

’07Camry hybrid_U (L/O 0610)

(b) Driver’s Seat Belt Reminder Light

and Buzzer

(c) Front Passenger’s Seat Belt Re-

minder Light and Buzzer

The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the “POWER” switch is set at ON or engine start, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer sounds for about 6 seconds. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for about 10 sec- onds. Then, if the seat belt is still unfas- tened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the front passen- ger’s seat belt is fastened. The vehicle speed linked seat belt remind- er buzzer can be disabled. For details, contact your Toyota dealer. However, Toyota the seat belt reminder buzzer be operational to alert the driver and front passenger that the seat belts are not fastened.

recommends

that

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the “POWER” switch is set at ON, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. Unless the front passenger fastens the belt, the light con- tinue flashing. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for about 10 sec- onds. Then, if the seat belt is still unfas- tened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the its front passenger seat, depending on weight, flash and buzzer to sound. The vehicle speed linked seat belt remind- er buzzer can be disabled. For details, contact your Toyota dealer.

the reminder

light

to

153

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank

If the fuel tank is empty, refuel immedi- ately.

D Loose fuel tank cap

If the fuel tank cap is loose, securely tighten it.

These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... There is a problem somewhere in the hy- brid system, emission control system, electronic trans- mission electrical system or warning light system itself. Contact your Toyota dealer as soon as possible to service the vehicle.

throttle control system,

if

control

system

inspection

Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” on page 345
in Section 6. (f) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.

that

recommends

However, Toyota the seat belt reminder buzzer be operational to alert the driver and front passenger that the seat belts are not fastened. (d) Charging System Warning Light When there are problems in the charging system while the hybrid system is running, the warning light comes on.

NOTICE

is

When the charging system warning light comes on while the hybrid sys- running, malfunctions may tem have occurred. light comes on, immediately stop the ve- hicle in a safe place and contact your Toyota dealer.

If the warning

lamp

comes

(e) Malfunction Indicator Lamp This the “POWER” switch is set at ON and goes off when the “READY” light comes on. This means light system is operating properly.

the warning

on when

that

154

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the

light goes off when

(g) “ABS” Warning Light This light comes on when the “POWER” switch is set at ON. If the anti−lock brake system function of the VDIM (vehicle dy- namics integrated management) is working properly, the “READY” light comes on. Thereafter, if the function malfunctions, the light comes on again. When the “ABS” warning light is on and the yellow brake system warning light is on, the anti−lock brake system function and the brake assist function of the VDIM may not operate so that the wheel could lock up during a sudden braking or brak- ing on slippery road surfaces However, the brake system still operates conven- tionally.

the

this

following conditions If any of occurs, indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the

“POWER” switch is set at ON.

D The

light

remains on when

the

“READY” light is on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem. If the light comes on together with the red brake system warning light, stop the ve- hicle immediately. For details, see “(a) Brake system warning light”.

Either of the following conditions may occur, but does not indicate the mal- function: D The light may stay on for about 60
seconds after is started. It is normal if the light goes off after a while.

the hybrid system

D Depressing the brake pedal repeatedly may turn on the light. It is normal if the light goes off after a few seconds.

CAUTION

If the “ABS” warning light remains on together with the red brake system warning light, stop your vehicle im- mediately in a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system function and brake as- sist function will fail but also the ve- hicle will become extremely unstable during braking.

155

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(h) Electric Power Steering System

Warning Light

light comes on when This steering control system fails.

the power

CAUTION

If this light comes on, take your ve- hicle to the Toyota dealer as soon as possible. In this case, you may feel the heavy steering wheel maneuver- ing. Drive your vehicle while gripping the steering wheel firmly.

(i) Open Door Warning Light and Buzz-

er

This light remains on until all the doors and trunk lid are completely closed. The buzzer also sounds once when any of the doors or trunk lid is not completely closed at the vehicle speed 5 km/h (3
mph) or more. Stop the vehicle and close the door and trunk lid completely.

156

light system monitors

indicator comes on when

(j) SRS Warning Light This the “POWER” switch is set at ON. It goes off after about 6 seconds. This means the SRS front airbags and seat belt pre- tensioners are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system, “AIRBAG ON” indi- cator light, “AIRBAG OFF” indicator light, front passenger’s seat belt buckle switch, seat belt pretensioner assemblies, inflat- ors, interconnecting wiring and power sources. If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible to. D The light does not come on when the “POWER” switch is set at ON or re- mains on for more than 6 seconds.

D The light comes on or starts flashing

while driving.

is

tire)

The SRS warning light and “AIRBAG OFF” indicator light will come on if there is a malfunction in the front passenger occu- pant classification system. (k) Low Tire Pressure Warning Light This light warns that the tire pressure of one or more of your tires (including the spare low. The light comes on when the “POWER” switch is set at ON. It goes off when the “READY” light comes on. This indicates that the tire pressure warning system is functioning properly. If the warning light comes on, stop your vehicle in a safe place as soon as pos- sible and check that the inflation pressure of all tires (including the spare tire) is as specified on the tire and loading informa- tion inflation pressure” on page 359 in Section 7−2.) The light should go off a few minutes after the tire pressure is adjusted. If the warning light blinks (comes on after blinking for 1 minute), the tire pressure warning system may be malfunctioning. Contact your Toyota dealer. For details, see “Tire pressure warning system” on page 168 in Section 1−7.

label. (See “Checking

tire

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

(l) Master Warning Light If the master warning light comes on, a message appears on the multi−information display. Depending on the conditions a warning tone may sound. (m) Parking Brake Reminder Buzzer The buzzer acts once when the parking brake is not completely released at the vehicle speed of 5 km/h (3 mph) or more. Stop the vehicle and release the parking brake fully.

’07Camry hybrid_U (L/O 0610)

SERVICE

CHECKING REMINDER INDICATORS (except the low fuel level warning light) 1. Apply the parking brake. 2. Open one of the doors.

The open door warning come on.

light should

3. Close the door.

The open door warning light should go off.

There may be the case that the red and yellow brake system warning lights and “ABS” warning light stay on for about 60
seconds. It is normal if they go out after a while. If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

4. With your

foot off

the brake pedal, press the “POWER” switch and set it at ON. All the service reminder indicators ex- cept the open door warning light should come on. The electric power steering warning light goes off after a few sec- onds. The SRS warning light goes off after about 6 seconds.

5. With depressing the brake pedal, press

the “POWER” switch.

All of the service reminder indicators ex- cept the red brake system warning light and driver’s seat belt reminder light go off when the “READY” light comes on. The driver’s seat belt reminder light goes off when the driver’s seat belt is fastened. The red brake system warning light goes off when the parking brake is released.

157

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

158

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS POWER switch, Transmission and Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “POWER” switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission Vehicle dynamics integrated management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tire pressure warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160
162
164
168
175
176

159

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

“POWER” switch

First time—ACC (accessory) mode (illu- minates amber) Accessories such as the radio operate. Second time—ON mode (illuminates am- ber) All accessories on. Third time—Power off (indicator off) Pressing the “POWER” switch again re- turns the mode switch to ACC.

light

When the key is in the vehicle, press- ing the “POWER” switch (hybrid system start−up switch) allows you to start and stop the hybrid system or choose at the ACC, ON, or “POWER” switch off. When the brake pedal is not depressed, pressing the “POWER” switch changes the mode as follows. Press the switch slowly and firmly.

160

If a buzzer sounds and the master warn- ing light comes on for 5 seconds when pressing the “POWER” switch, this indi- cates that the key is not in the vehicle. The message “KEY IS NOT DETECTED” will also appear on the multi−information display. If the brake pedal is depressed, the in- dicator light will turn green, regardless of which mode is selected. When the indicator is green, pressing the “POWER” switch once turns the hybrid system on. (For starting tips, see “How to start the hybrid system” on page 301
in Section 3.)

light

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

function memorizes

is discon- When the 12 volt battery nected or run down, the push button start current mode. After you reconnect, replace, or re- charge the battery, the memorized mode is selected automatically. In any of these cases, turn off the hybrid system if the hybrid system is turned on.

the

indicator

light on

to off and

the amber

then changed

the hybrid system

the “POWER” switch

When is changed from ON (with the hybrid system turned off) to ACC, “DEPRESS THE BRAKE PEDAL” will appear on the multi−information display. If the “POWER” switch blinks, this indicates a malfunction of the push start system. Turn off immediately and contact your Toyota dealer. Approximately five hours after the hybrid system is turned off, you may hear sound coming from underneath the trunk for sev- eral minutes. This is normal operation and does not indicate a malfunction. (See “Leak detection pump” on page ix.) It is not a malfunction if the needle on all meters and gauges move slightly when the “POWER” switch is set at ACC, ON or when the hybrid system is turned on.

NOTICE

Do not leave the “POWER” switch at ACC or ON with the hybrid system turned off. The 12 volt battery will discharge.

161

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Transmission

Shift with the brake pedal depressed. (The “POWER” switch must be set at ON.)

Shift normally.

162

’07Camry hybrid_U (L/O 0610)

Selector lever

the possibility of

Your transmission has a shift lock system to minimize incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the “POWER” switch set at ON). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, hybrid system starting R: Reverse N: Neutral D: Normal driving B: Engine braking

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(b) Normal driving 1. Start the hybrid system as instructed in “How to start the hybrid system” on page 301 in Section 3. The transmis- sion must be in “P”.

2. With your foot holding down the brake

pedal, shift the selector lever to “D”.

CAUTION

Never put your foot on the accelera- tor pedal while shifting.

3. Release the parking brake and brake the accelerator pedal

pedal. Depress slowly for smooth starting.

CAUTION

Always keep your foot on the brake pedal while stopped with the hybrid system on. This prevents the vehicle from creeping.

NOTICE

Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.

(c) Using engine braking To use engine braking intentionally, shift the selector lever to the “B” position and take your foot off the accelerator pedal. During high speed driving you may feel that engine braking is less effective than that of conventional vehicle. Do not continue normal driving with the transmission long time. This may cause decreased fuel econo- my.

in “B” for a

CAUTION

Be careful when using engine braking on a slippery surface. Abrupt shifting could cause the vehicle to spin or skid.

(d) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.

NOTICE

Never shift into reverse while the ve- hicle is moving.

(e) Parking 1. Bring the vehicle to a complete stop. 2. With

the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.

3. With

the brake pedal pressed down, shift the selector lever to the “P” posi- tion.

When turning the hybrid system off, put the transmission in the “P” position.

CAUTION

Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.

163

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

(f)

If you cannot shift the selector le- ver out of “P” position

is depressed, use

If you cannot shift the selector lever from the “P” position even though the brake pedal lock override button. For instructions, see “If you cannot shift transmission selector le- ver” on page 329 in Section 4.

the shift

164

’07Camry hybrid_U (L/O 0610)

Vehicle dynamics integrated management Vehicle dynamics integrated manage- ment (VDIM) is designed to control ve- hicle motion continuously using all pos- sible functions to stabilize the motion. It is important to keep the tires in good condition for the system to properly control vehicle motion. Refer to the in- formation tires on pages 359
through 367 in Section 7−2. The system has the functions listed below. Each function becomes operational when the vehicle speed exceeds the speeds as shown below. D Brake assist function

for

7 km/h (4 mph)

D Anti−lock brake system function

7 km/h (4 mph)

D Traction control function

0 km/h (0 mph)

D Vehicle stability control function

15 km/h (9 mph)

CAUTION

D Do not

rely excessively on

the VDIM. Even if the system is operat- ing, you must always drive carefully and attentively. Reckless driving will result in an unexpected accident. If the slip indicator flashes, special care should be taken.

D Only use tires of specified size. The size, manufacturer, brand and tread pattern for all 4 tires should be the same. If you use any tires other than specified, or different types or sizes, the VDIM may not function correctly. When replacing the tires or wheels, contact your Toyota deal- er.

D Do not modify the suspensions. If the

you modify VDIM may not function correctly.

the suspensions,

D In situations where the road surface is covered with ice or snow, snow tires or tire chains should be used.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

While the VDIM is using its various func- tions to stabilize vehicle motion, the slip indicator in the instrument cluster flashes and the buzzer sounds. Drive carefully when you are in situations where the indi- cator flashes. You may feel some vibra- tions from the underbody and you may feel some the steering wheel when the VDIM is using its various functions.

resistance when

turning

Slip indicator light

“ABS” warning light (U.S.A.)

When the “POWER” switch is set at ON is turned on, the slip indicator light comes on. It will go off when the “READY” light comes on. If the slip indicator light does not come on when the “POWER” switch is set at ON, contact your Toyota dealer.

“ABS” warning light (Canada)

165

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

“ABS” warning light When the “POWER” switch is set at ON, the “ABS” warning light comes on. It will go off when the “READY” light comes on. If the “ABS” warning light does not come on when the “POWER” switch is set at ON, contact your Toyota dealer. If the “ABS” warning light remains on after the “POWER” switch is set at ON it comes on while driving, the or anti−lock brake system function may not operate properly. Although the brake system operates without the func- tion, drive carefully and have your ve- hicle checked by a Toyota dealer as soon as possible. For details, see “Ser- vice reminder indicators and warning buzzers” on page 150 in Section 1−6.

if

166

Message “CHECK VSC SYSTEM”

If “CHECK VSC SYSTEM” appears on the multi−information display, the trac- tion control and vehicle stability control functions may not operate properly. Al- though the brake system operates nor- mally without functions, drive carefully and have your vehicle checked by a Toyota dealer as soon as possible. For details, see “—Messages” on page 140 in Section 1−6.

these

BRAKE ASSIST FUNCTION The brake assist function is designed to assist with emergency braking. When the driver suddenly depresses the brake ped- al, the device treats it as emergency brak- ing and adds braking force. If you slam the brakes on or apply the brakes more firmly, more powerful braking will be applied.

CAUTION

The brake assist function is not de- signed to shorten braking distance. Always drive at a moderate speed and maintain a safe distance from the ve- hicle in front of you. Depending on road conditions, braking distance may be longer than that of a vehicle with- out the brake assist device. If tire chains are used, braking distance may become longer.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

to help prevent

ANTI−LOCK BRAKE SYSTEM FUNCTION The anti−lock brake system function is de- signed the wheels during sudden braking or when braking on slippery road conditions. This assists in providing directional stability and steering performance of the vehicle under these circumstances.

lock−up of

the brake pedal

Effective way to press the ABS brake pedal: When is de- pressed and the anti−lock brake system function is in action, the slip indicator flashes. In this situation, to let the anti− lock brake system work for you, just hold the brake pedal down more firmly. Do not pump the brake in a panic stop. This will result in reduced braking per- formance.

Depressing the brake pedal on slippery road surfaces such as on a manhole cov- er, a steel plate at a construction site, joints in a bridge, etc. on a rainy day tends to activate the anti−lock brake sys- tem function.

’07Camry hybrid_U (L/O 0610)

When the anti−lock brake system function is activated, you may hear the anti−lock brake system function operating sound and the vibrations of the vehicle body and steering wheel. You may also hear the motor sound in the engine compartment even after the vehicle is stopped. Howev- er, it does not indicate any trouble.

CAUTION

The anti−lock brake system function is not designed to shorten braking distance. Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. De- pending on road conditions, braking distance may be longer than that of a vehicle without the anti−lock brake system. If tire chains are used, brak- ing distance may become longer.

Compared with vehicles without an anti−lock brake device, your vehicle may require a longer stopping dis- tance in the following cases: D Driving on rough, gravel or snow−

covered roads.

D Driving with tire chains installed. D Driving over the steps such as the

joints on the road.

D Driving on roads where the road surface is pitted or has other differ- ences in surface height.

If tire grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the anti−lock brake system does not provide vehicle control.

167

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

TRACTION CONTROL FUNCTION The traction control function is designed to help prevent skid of the drive wheels dur- ing sudden acceleration on slippery road surfaces. You may feel vibration or noise in your vehicle, caused by operation of the brakes.

CAUTION

Under certain slippery road condi- tions, full traction of the vehicle and power against drive wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with tire chains. Always snow drive at a moderate speed.

the vehicle

tires or

lose

to

CONTROL

STABILITY

VEHICLE FUNCTION The vehicle stability control function is de- signed to help prevent skid of the wheels while cornering on slippery road surfaces or when turning the steering wheel abrupt- ly. The system controls the driving and brak- ing forces on each tire and also controls the power steering assistance to help the driver to recover vehicle stability.

CAUTION

Depending on the road conditions, the vehicle stability control function may not be able to stabilize your ve- hicle. Always drive at a moderate speed.

Tire pressure warning system The tire pressure warning system warns you that the tire inflation pressure is low. The tire pressure warning system is not a substitute for checking normal tire infla- tion pressure. Check inflation pressure with a tire pressure gauge regu- larly.

tire

the

CAUTION

The warning system may not activate immediately if bursts or sudden air leakage should occur.

168

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Indicator

status

ON

ON after blinking for 1 minute

’07Camry hybrid_U (L/O 0610)

Meanings

Do this

CAUTION

Tire inflation pressure is low

Tire pres- sure warn- ing system malfunction

Adjust the tire inflation pressure Have the system checked at your Toyota dealer

the

tire pressure warning

If light comes on, be sure to observe the following precautions. Failure to do so could cause loss of vehicle control and result in death or serious injury. D Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pressure immediately. D If the tire pressure warning

light comes on even after tire inflation pressure adjustment, it is probable that you have a flat tire. Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota deal- er.

D Avoid abrupt maneuvering and bra- king. If the vehicle tires deteriorate, you could lose control of the steer- ing wheel or the brakes.

169

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

The tire pressure warning light comes on when the “POWER” switch is set at ON and goes off after a few seconds. This means the tire pressure warning light is operating properly. If the tire inflation pres- sure becomes light comes on again. In this case, adjusting the tire infla- tion pressure will turn off the light after a few minutes. If the light comes on after blinking the tire pressure warning system is not working properly.

for 1 minute,

low,

the

’07Camry hybrid_U (L/O 0610)

The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temperature. In this case, ad- justing the tire inflation pressure will turn off the light after a few minutes. Pushing the tire pressure warning reset switch does not turn off the tire pressure warning light. Adjusting the tire inflation pressure will turn off the light. The compact spare tire is not equipped with the tire pressure warning valve and transmitter. If a tire goes flat, the warning light will not turn off even though the flat tire is replaced with the spare tire. Re- place the spare tire with the repaired tire and adjust the proper tire inflation pressur- e. The tire pressure warning light will turn off after a few minutes.

CAUTION

Each tire, including the spare (if pro- vided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label). (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label (tire and load information label), you should determine the proper tire infla- tion pressure for those tires.)

As an added safety feature, your ve- hicle has been equipped with a tire pressure monitoring system (TPMS– tire pressure warning system) that il- luminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under−inflated. Accordingly, when the low tire pressure telltale (tire pres- sure warning illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a sig- nificantly under−inflated tire causes the tire to overheat and can lead to tire failure. Under−inflation also re- duces fuel efficiency and tire tread life, and may affect the vehicle’s han- dling and stopping ability.

light)

170

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

is

the driver’s responsibility

Please note that the TPMS (tire pres- sure warning system) is not a substi- tute for proper tire maintenance, and it to maintain correct tire pressure, even if under−inflation has not reached the level illumination of the TPMS low tire pressure telltale (tire pressure warning light).

trigger

to

’07Camry hybrid_U (L/O 0610)

NOTICE

z Do not use liquid sealants for a flat tire as tire pressure warning valve and transmitter will be damaged.

z When the tires must be repaired or replaced, have them repaired or re- placed by the nearest Toyota dealer or authorized tire dealer. The tire pressure warning valves and trans- mitters will be affected by the installation or removal of tires.

IF THE TIRE PRESSURE WARNING LIGHT BLINKS (comes on after blinking for 1 minute )... If the tire pressure warning light blinks (comes on after blinking for 1 minute) when the “POWER” switch is set at ON, the tire pressure warning system is not working properly. The system will be disabled in the follow- ing conditions: (When the condition becomes normal, the system will work properly.) D If tires not equipped with tire pressure transmitters are

warning valves and used.

171

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

D If

the ID code on the

tire pressure warning valves and transmitters is not registered on the tire pressure warning ECU.

D If electronic devices or facilities using frequencies are

radio wave

similar nearby.

D If a radio set at similar frequencies is

in use in the vehicle.

D If a window tint that affects the radio

wave signals is installed.

D If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings.

D If non−genuine Toyota wheels are used. D If tire chains are used. D If

the tire inflation pressure is more than 500 kPa (5.1 kgf/cm2 or bar, 73
psi).

If the tire pressure warning light comes on after blinking for 1 minute frequently when the “POWER” switch is set at ON, have it checked by your Toyota dealer. Even if you use genuine wheels, the tire pressure warning system may not work properly with some types of tires.

172

’07Camry hybrid_U (L/O 0610)

Pushing the tire pressure warning reset switch should not turn off the tire pressure warning light.

For vehicles sold in U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation.

received,

including

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

interference

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures: −Reorient or relocate the receiving an- tenna. −Increase equipment and receiver.

the separation between

to radio or

the

’07Camry hybrid_U (L/O 0610)

−Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. −Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

For vehicles sold in Canada

(1)

Operation is subject to the following two conditions: this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

the

transmitters.

replacing a

ID codes on

REPLACING TIRES AND WHEELS When replacing the tires and wheels, be sure to install tire pressure warning valves and tire pressure warning valves and transmitters are registered on the tire pressure warning ECU. When tire pressure warning valve and transmitter, it is neces- sary to register the ID code of tire pres- sure warning valve and transmitter. Have the ID code registered by your Toyota dealer. If the ID code is not registered the sys- tem will not work properly, After about 1
hour, the tire pressure warning light come on after blinking for 1 minute to indicate a system malfunction.

NOTICE

When the tires or tire pressure warn- ing valves and transmitters must be replaced, have them replaced by your Toyota dealer. The tire pressure warn- ing valves and transmitters will be affected by the installation or removal of tires.

173

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

D When changing the tire size. To initialize the system, perform the fol- lowing: 1. Park the vehicle in a safe place and

turn the “POWER” switch off.

2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level. (See “Tires” on page 385 in Section 8.)

3. Press the “POWER” switch and set it

at ON.

TIRE PRESSURE WARNING RESET SWITCH When initializing the system, the present tire inflation pressure is stored as stan- dard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is neces- sary to initialize the tire pressure warning system. D When rotating the tires on vehicles dif- fering with front and rear tire inflation pressures.

174

4. Open the glove box, and push and hold the tire pressure warning reset switch until light blinks slowly three times.

tire pressure warning

the

5. Leave the system for a few minutes with the “POWER” switch set at ON and then turn the “POWER” switch off. If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust to the specified level and initialize the system again.

the tire inflation pressure

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning sys- tem may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Parking brake

CAUTION

Do not push the reset switch without adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually nor- mal.

Type A

Type B

’07Camry hybrid_U (L/O 0610)

the parking brake

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal while depressing the brake pedal. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake. A warning message “PARK BRAKE” ap- pears on the multi−information display and a warning tone sounds to remind you to release the parking brake when the ve- hicle speed rises above 5 km/h (3 mph) with the parking brake is applied.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

175

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Cruise control The cruise control is designed to main- tain a set cruising speed without requir- ing the driver to operate the accelera- tor. Cruising speed can be set to any speed above 40 km/h (25 mph). Within the limits of the vehicle capabili- ties, cruising speed can be maintained up or down grades. However, changes in ve- hicle speed may occur on steeper grades.

CAUTION

D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

176

’07Camry hybrid_U (L/O 0610)

CAUTION

To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the cruise control indicator light is off.

TURNING THE SYSTEM ON AND OFF To turn the cruise control on, press the “ON−OFF” button. The cruise control indi- cator light on the instrument panel will come on to indicate that the cruise control is operational. Pressing “ON−OFF” button again turns the system off. When the system is turned off, cruising speed must be reset when the cruise con- trol is turned on again.

the

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration. CANCELLING THE CRUISE CONTROL The cruise control may be temporarily cancelled by the driver or by the system itself under certain circumstances. Tempo- rary cancellation allows the set cruising speed to remain in memory. The cruise control can be temporarily can- celled by doing the following: D Pulling the lever in the “CANCEL” di-

rection and releasing it

D Depressing the brake pedal Under certain circumstances, control is temporarily cancelled: D When vehicle speed

the cruise

falls below 40

km/h (25 mph)

D When vehicle stability control is acti-

vated

When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con- trol the set speed is erased from memory.

is cancelled and

The cruise control indicator light remains on to indicate that the system is still in operation. To turn the cruise control off, press the “ON−OFF” button. Make sure the cruise