2007 Toyota Camry HV Owners Manual

foot off

the brake pedal, press the “POWER” switch and set it at ON. All the service reminder indicators ex- cept the open door warning light should come on. The electric power steering warning light goes off after a few sec- onds. The SRS warning light goes off after about 6 seconds.

5. With depressing the brake pedal, press

the “POWER” switch.

All of the service reminder indicators ex- cept the red brake system warning light and driver’s seat belt reminder light go off when the “READY” light comes on. The driver’s seat belt reminder light goes off when the driver’s seat belt is fastened. The red brake system warning light goes off when the parking brake is released.

157

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

158

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS POWER switch, Transmission and Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “POWER” switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission Vehicle dynamics integrated management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tire pressure warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160
162
164
168
175
176

159

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

“POWER” switch

First time—ACC (accessory) mode (illu- minates amber) Accessories such as the radio operate. Second time—ON mode (illuminates am- ber) All accessories on. Third time—Power off (indicator off) Pressing the “POWER” switch again re- turns the mode switch to ACC.

light

When the key is in the vehicle, press- ing the “POWER” switch (hybrid system start−up switch) allows you to start and stop the hybrid system or choose at the ACC, ON, or “POWER” switch off. When the brake pedal is not depressed, pressing the “POWER” switch changes the mode as follows. Press the switch slowly and firmly.

160

If a buzzer sounds and the master warn- ing light comes on for 5 seconds when pressing the “POWER” switch, this indi- cates that the key is not in the vehicle. The message “KEY IS NOT DETECTED” will also appear on the multi−information display. If the brake pedal is depressed, the in- dicator light will turn green, regardless of which mode is selected. When the indicator is green, pressing the “POWER” switch once turns the hybrid system on. (For starting tips, see “How to start the hybrid system” on page 301
in Section 3.)

light

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

function memorizes

is discon- When the 12 volt battery nected or run down, the push button start current mode. After you reconnect, replace, or re- charge the battery, the memorized mode is selected automatically. In any of these cases, turn off the hybrid system if the hybrid system is turned on.

the

indicator

light on

to off and

the amber

then changed

the hybrid system

the “POWER” switch

When is changed from ON (with the hybrid system turned off) to ACC, “DEPRESS THE BRAKE PEDAL” will appear on the multi−information display. If the “POWER” switch blinks, this indicates a malfunction of the push start system. Turn off immediately and contact your Toyota dealer. Approximately five hours after the hybrid system is turned off, you may hear sound coming from underneath the trunk for sev- eral minutes. This is normal operation and does not indicate a malfunction. (See “Leak detection pump” on page ix.) It is not a malfunction if the needle on all meters and gauges move slightly when the “POWER” switch is set at ACC, ON or when the hybrid system is turned on.

NOTICE

Do not leave the “POWER” switch at ACC or ON with the hybrid system turned off. The 12 volt battery will discharge.

161

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Transmission

Shift with the brake pedal depressed. (The “POWER” switch must be set at ON.)

Shift normally.

162

’07Camry hybrid_U (L/O 0610)

Selector lever

the possibility of

Your transmission has a shift lock system to minimize incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the “POWER” switch set at ON). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, hybrid system starting R: Reverse N: Neutral D: Normal driving B: Engine braking

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(b) Normal driving 1. Start the hybrid system as instructed in “How to start the hybrid system” on page 301 in Section 3. The transmis- sion must be in “P”.

2. With your foot holding down the brake

pedal, shift the selector lever to “D”.

CAUTION

Never put your foot on the accelera- tor pedal while shifting.

3. Release the parking brake and brake the accelerator pedal

pedal. Depress slowly for smooth starting.

CAUTION

Always keep your foot on the brake pedal while stopped with the hybrid system on. This prevents the vehicle from creeping.

NOTICE

Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.

(c) Using engine braking To use engine braking intentionally, shift the selector lever to the “B” position and take your foot off the accelerator pedal. During high speed driving you may feel that engine braking is less effective than that of conventional vehicle. Do not continue normal driving with the transmission long time. This may cause decreased fuel econo- my.

in “B” for a

CAUTION

Be careful when using engine braking on a slippery surface. Abrupt shifting could cause the vehicle to spin or skid.

(d) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.

NOTICE

Never shift into reverse while the ve- hicle is moving.

(e) Parking 1. Bring the vehicle to a complete stop. 2. With

the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.

3. With

the brake pedal pressed down, shift the selector lever to the “P” posi- tion.

When turning the hybrid system off, put the transmission in the “P” position.

CAUTION

Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.

163

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

(f)

If you cannot shift the selector le- ver out of “P” position

is depressed, use

If you cannot shift the selector lever from the “P” position even though the brake pedal lock override button. For instructions, see “If you cannot shift transmission selector le- ver” on page 329 in Section 4.

the shift

164

’07Camry hybrid_U (L/O 0610)

Vehicle dynamics integrated management Vehicle dynamics integrated manage- ment (VDIM) is designed to control ve- hicle motion continuously using all pos- sible functions to stabilize the motion. It is important to keep the tires in good condition for the system to properly control vehicle motion. Refer to the in- formation tires on pages 359
through 367 in Section 7−2. The system has the functions listed below. Each function becomes operational when the vehicle speed exceeds the speeds as shown below. D Brake assist function

for

7 km/h (4 mph)

D Anti−lock brake system function

7 km/h (4 mph)

D Traction control function

0 km/h (0 mph)

D Vehicle stability control function

15 km/h (9 mph)

CAUTION

D Do not

rely excessively on

the VDIM. Even if the system is operat- ing, you must always drive carefully and attentively. Reckless driving will result in an unexpected accident. If the slip indicator flashes, special care should be taken.

D Only use tires of specified size. The size, manufacturer, brand and tread pattern for all 4 tires should be the same. If you use any tires other than specified, or different types or sizes, the VDIM may not function correctly. When replacing the tires or wheels, contact your Toyota deal- er.

D Do not modify the suspensions. If the

you modify VDIM may not function correctly.

the suspensions,

D In situations where the road surface is covered with ice or snow, snow tires or tire chains should be used.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

While the VDIM is using its various func- tions to stabilize vehicle motion, the slip indicator in the instrument cluster flashes and the buzzer sounds. Drive carefully when you are in situations where the indi- cator flashes. You may feel some vibra- tions from the underbody and you may feel some the steering wheel when the VDIM is using its various functions.

resistance when

turning

Slip indicator light

“ABS” warning light (U.S.A.)

When the “POWER” switch is set at ON is turned on, the slip indicator light comes on. It will go off when the “READY” light comes on. If the slip indicator light does not come on when the “POWER” switch is set at ON, contact your Toyota dealer.

“ABS” warning light (Canada)

165

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

“ABS” warning light When the “POWER” switch is set at ON, the “ABS” warning light comes on. It will go off when the “READY” light comes on. If the “ABS” warning light does not come on when the “POWER” switch is set at ON, contact your Toyota dealer. If the “ABS” warning light remains on after the “POWER” switch is set at ON it comes on while driving, the or anti−lock brake system function may not operate properly. Although the brake system operates without the func- tion, drive carefully and have your ve- hicle checked by a Toyota dealer as soon as possible. For details, see “Ser- vice reminder indicators and warning buzzers” on page 150 in Section 1−6.

if

166

Message “CHECK VSC SYSTEM”

If “CHECK VSC SYSTEM” appears on the multi−information display, the trac- tion control and vehicle stability control functions may not operate properly. Al- though the brake system operates nor- mally without functions, drive carefully and have your vehicle checked by a Toyota dealer as soon as possible. For details, see “—Messages” on page 140 in Section 1−6.

these

BRAKE ASSIST FUNCTION The brake assist function is designed to assist with emergency braking. When the driver suddenly depresses the brake ped- al, the device treats it as emergency brak- ing and adds braking force. If you slam the brakes on or apply the brakes more firmly, more powerful braking will be applied.

CAUTION

The brake assist function is not de- signed to shorten braking distance. Always drive at a moderate speed and maintain a safe distance from the ve- hicle in front of you. Depending on road conditions, braking distance may be longer than that of a vehicle with- out the brake assist device. If tire chains are used, braking distance may become longer.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

to help prevent

ANTI−LOCK BRAKE SYSTEM FUNCTION The anti−lock brake system function is de- signed the wheels during sudden braking or when braking on slippery road conditions. This assists in providing directional stability and steering performance of the vehicle under these circumstances.

lock−up of

the brake pedal

Effective way to press the ABS brake pedal: When is de- pressed and the anti−lock brake system function is in action, the slip indicator flashes. In this situation, to let the anti− lock brake system work for you, just hold the brake pedal down more firmly. Do not pump the brake in a panic stop. This will result in reduced braking per- formance.

Depressing the brake pedal on slippery road surfaces such as on a manhole cov- er, a steel plate at a construction site, joints in a bridge, etc. on a rainy day tends to activate the anti−lock brake sys- tem function.

’07Camry hybrid_U (L/O 0610)

When the anti−lock brake system function is activated, you may hear the anti−lock brake system function operating sound and the vibrations of the vehicle body and steering wheel. You may also hear the motor sound in the engine compartment even after the vehicle is stopped. Howev- er, it does not indicate any trouble.

CAUTION

The anti−lock brake system function is not designed to shorten braking distance. Always drive at a moderate speed and maintain a safe distance from the vehicle in front of you. De- pending on road conditions, braking distance may be longer than that of a vehicle without the anti−lock brake system. If tire chains are used, brak- ing distance may become longer.

Compared with vehicles without an anti−lock brake device, your vehicle may require a longer stopping dis- tance in the following cases: D Driving on rough, gravel or snow−

covered roads.

D Driving with tire chains installed. D Driving over the steps such as the

joints on the road.

D Driving on roads where the road surface is pitted or has other differ- ences in surface height.

If tire grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the anti−lock brake system does not provide vehicle control.

167

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

TRACTION CONTROL FUNCTION The traction control function is designed to help prevent skid of the drive wheels dur- ing sudden acceleration on slippery road surfaces. You may feel vibration or noise in your vehicle, caused by operation of the brakes.

CAUTION

Under certain slippery road condi- tions, full traction of the vehicle and power against drive wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with tire chains. Always snow drive at a moderate speed.

the vehicle

tires or

lose

to

CONTROL

STABILITY

VEHICLE FUNCTION The vehicle stability control function is de- signed to help prevent skid of the wheels while cornering on slippery road surfaces or when turning the steering wheel abrupt- ly. The system controls the driving and brak- ing forces on each tire and also controls the power steering assistance to help the driver to recover vehicle stability.

CAUTION

Depending on the road conditions, the vehicle stability control function may not be able to stabilize your ve- hicle. Always drive at a moderate speed.

Tire pressure warning system The tire pressure warning system warns you that the tire inflation pressure is low. The tire pressure warning system is not a substitute for checking normal tire infla- tion pressure. Check inflation pressure with a tire pressure gauge regu- larly.

tire

the

CAUTION

The warning system may not activate immediately if bursts or sudden air leakage should occur.

168

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Indicator

status

ON

ON after blinking for 1 minute

’07Camry hybrid_U (L/O 0610)

Meanings

Do this

CAUTION

Tire inflation pressure is low

Tire pres- sure warn- ing system malfunction

Adjust the tire inflation pressure Have the system checked at your Toyota dealer

the

tire pressure warning

If light comes on, be sure to observe the following precautions. Failure to do so could cause loss of vehicle control and result in death or serious injury. D Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pressure immediately. D If the tire pressure warning

light comes on even after tire inflation pressure adjustment, it is probable that you have a flat tire. Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota deal- er.

D Avoid abrupt maneuvering and bra- king. If the vehicle tires deteriorate, you could lose control of the steer- ing wheel or the brakes.

169

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

The tire pressure warning light comes on when the “POWER” switch is set at ON and goes off after a few seconds. This means the tire pressure warning light is operating properly. If the tire inflation pres- sure becomes light comes on again. In this case, adjusting the tire infla- tion pressure will turn off the light after a few minutes. If the light comes on after blinking the tire pressure warning system is not working properly.

for 1 minute,

low,

the

’07Camry hybrid_U (L/O 0610)

The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temperature. In this case, ad- justing the tire inflation pressure will turn off the light after a few minutes. Pushing the tire pressure warning reset switch does not turn off the tire pressure warning light. Adjusting the tire inflation pressure will turn off the light. The compact spare tire is not equipped with the tire pressure warning valve and transmitter. If a tire goes flat, the warning light will not turn off even though the flat tire is replaced with the spare tire. Re- place the spare tire with the repaired tire and adjust the proper tire inflation pressur- e. The tire pressure warning light will turn off after a few minutes.

CAUTION

Each tire, including the spare (if pro- vided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label). (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label (tire and load information label), you should determine the proper tire infla- tion pressure for those tires.)

As an added safety feature, your ve- hicle has been equipped with a tire pressure monitoring system (TPMS– tire pressure warning system) that il- luminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under−inflated. Accordingly, when the low tire pressure telltale (tire pres- sure warning illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a sig- nificantly under−inflated tire causes the tire to overheat and can lead to tire failure. Under−inflation also re- duces fuel efficiency and tire tread life, and may affect the vehicle’s han- dling and stopping ability.

light)

170

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

is

the driver’s responsibility

Please note that the TPMS (tire pres- sure warning system) is not a substi- tute for proper tire maintenance, and it to maintain correct tire pressure, even if under−inflation has not reached the level illumination of the TPMS low tire pressure telltale (tire pressure warning light).

trigger

to

’07Camry hybrid_U (L/O 0610)

NOTICE

z Do not use liquid sealants for a flat tire as tire pressure warning valve and transmitter will be damaged.

z When the tires must be repaired or replaced, have them repaired or re- placed by the nearest Toyota dealer or authorized tire dealer. The tire pressure warning valves and trans- mitters will be affected by the installation or removal of tires.

IF THE TIRE PRESSURE WARNING LIGHT BLINKS (comes on after blinking for 1 minute )... If the tire pressure warning light blinks (comes on after blinking for 1 minute) when the “POWER” switch is set at ON, the tire pressure warning system is not working properly. The system will be disabled in the follow- ing conditions: (When the condition becomes normal, the system will work properly.) D If tires not equipped with tire pressure transmitters are

warning valves and used.

171

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

D If

the ID code on the

tire pressure warning valves and transmitters is not registered on the tire pressure warning ECU.

D If electronic devices or facilities using frequencies are

radio wave

similar nearby.

D If a radio set at similar frequencies is

in use in the vehicle.

D If a window tint that affects the radio

wave signals is installed.

D If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings.

D If non−genuine Toyota wheels are used. D If tire chains are used. D If

the tire inflation pressure is more than 500 kPa (5.1 kgf/cm2 or bar, 73
psi).

If the tire pressure warning light comes on after blinking for 1 minute frequently when the “POWER” switch is set at ON, have it checked by your Toyota dealer. Even if you use genuine wheels, the tire pressure warning system may not work properly with some types of tires.

172

’07Camry hybrid_U (L/O 0610)

Pushing the tire pressure warning reset switch should not turn off the tire pressure warning light.

For vehicles sold in U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation.

received,

including

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

interference

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures: −Reorient or relocate the receiving an- tenna. −Increase equipment and receiver.

the separation between

to radio or

the

’07Camry hybrid_U (L/O 0610)

−Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. −Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

For vehicles sold in Canada

(1)

Operation is subject to the following two conditions: this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

the

transmitters.

replacing a

ID codes on

REPLACING TIRES AND WHEELS When replacing the tires and wheels, be sure to install tire pressure warning valves and tire pressure warning valves and transmitters are registered on the tire pressure warning ECU. When tire pressure warning valve and transmitter, it is neces- sary to register the ID code of tire pres- sure warning valve and transmitter. Have the ID code registered by your Toyota dealer. If the ID code is not registered the sys- tem will not work properly, After about 1
hour, the tire pressure warning light come on after blinking for 1 minute to indicate a system malfunction.

NOTICE

When the tires or tire pressure warn- ing valves and transmitters must be replaced, have them replaced by your Toyota dealer. The tire pressure warn- ing valves and transmitters will be affected by the installation or removal of tires.

173

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

D When changing the tire size. To initialize the system, perform the fol- lowing: 1. Park the vehicle in a safe place and

turn the “POWER” switch off.

2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level. (See “Tires” on page 385 in Section 8.)

3. Press the “POWER” switch and set it

at ON.

TIRE PRESSURE WARNING RESET SWITCH When initializing the system, the present tire inflation pressure is stored as stan- dard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is neces- sary to initialize the tire pressure warning system. D When rotating the tires on vehicles dif- fering with front and rear tire inflation pressures.

174

4. Open the glove box, and push and hold the tire pressure warning reset switch until light blinks slowly three times.

tire pressure warning

the

5. Leave the system for a few minutes with the “POWER” switch set at ON and then turn the “POWER” switch off. If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust to the specified level and initialize the system again.

the tire inflation pressure

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning sys- tem may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Parking brake

CAUTION

Do not push the reset switch without adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually nor- mal.

Type A

Type B

’07Camry hybrid_U (L/O 0610)

the parking brake

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal while depressing the brake pedal. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake. A warning message “PARK BRAKE” ap- pears on the multi−information display and a warning tone sounds to remind you to release the parking brake when the ve- hicle speed rises above 5 km/h (3 mph) with the parking brake is applied.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

175

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Cruise control The cruise control is designed to main- tain a set cruising speed without requir- ing the driver to operate the accelera- tor. Cruising speed can be set to any speed above 40 km/h (25 mph). Within the limits of the vehicle capabili- ties, cruising speed can be maintained up or down grades. However, changes in ve- hicle speed may occur on steeper grades.

CAUTION

D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

176

’07Camry hybrid_U (L/O 0610)

CAUTION

To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the cruise control indicator light is off.

TURNING THE SYSTEM ON AND OFF To turn the cruise control on, press the “ON−OFF” button. The cruise control indi- cator light on the instrument panel will come on to indicate that the cruise control is operational. Pressing “ON−OFF” button again turns the system off. When the system is turned off, cruising speed must be reset when the cruise con- trol is turned on again.

the

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration. CANCELLING THE CRUISE CONTROL The cruise control may be temporarily cancelled by the driver or by the system itself under certain circumstances. Tempo- rary cancellation allows the set cruising speed to remain in memory. The cruise control can be temporarily can- celled by doing the following: D Pulling the lever in the “CANCEL” di-

rection and releasing it

D Depressing the brake pedal Under certain circumstances, control is temporarily cancelled: D When vehicle speed

the cruise

falls below 40

km/h (25 mph)

D When vehicle stability control is acti-

vated

When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con- trol the set speed is erased from memory.

is cancelled and

The cruise control indicator light remains on to indicate that the system is still in operation. To turn the cruise control off, press the “ON−OFF” button. Make sure the cruise control indicator light is off. If the cruise control automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESUMING THE CRUISE CONTROL If the cruise control is temporarily can- celled, the cruising speed can be resumed by pushing the lever up in the “+ RES” direction. Vehicle speed must be above 40 km/h (25
mph). RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction.

177

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

SETTING THE CRUISING SPEED The transmission must be in “D” before you set the cruising speed. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed. If the speed is not satisfac- tory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6 km/h (1.0 mph). You can now take your foot off the accelerator pedal.

’07Camry hybrid_U (L/O 0610)

RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “− SET” direction. CRUISE CONTROL FAILURE WARNING If the cruise control indicator light flashes when using the cruise control, press the “ON−OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

178

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

179

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Audio and hands−free phone systems Reference Using your audio system Audio remote controls AUX adapter Audio system operating hints Hands−free phone system

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

181
181
201
202
203
210

For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”.

180

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Reference

Type 1: AM·FM radio/compact disc player (with compact disc changer controller)

Type 2: AM·FM radio/compact disc player with changer (with XM satellite radio∗ con- troller)

∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition switch is set at ACC or ON.

CAUTION

in U.S.A. and

For vehicles sold Canada: D Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifi- cations to this equipment will void the user’s authority to operate this device.

181

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

D Laser products

from

D Do not take this unit apart or at- tempt to make any changes your- self. This is an intricate unit that uses a laser pickup to retrieve in- formation the surface of compact discs. The laser is care- fully shielded so that its rays re- main the cabinet. There- fore, never try to disassemble the player or alter any of its parts since you may be exposed to la- ser rays and dangerous voltages.

inside

D This product utilizes a laser. Use of controls or adjustments or per- formance of procedures other than those specified herein may result in hazardous radiation ex- posure.

182

’07Camry hybrid_U (L/O 0610)

LISTENING TO THE XM SATELLITE RADIO BROADCAST∗ (type 2) To listen to a satellite radio broadcast in your vehicle, an additional genuine Toyota satellite receiver and antenna (or equiva- lents) must be purchased and installed. A subscription to the XM satellite radio ser- vice is also necessary. How to subscribe to an XM satellite radio An XM satellite radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 contiguous states.

TURNING THE SYSTEM ON AND OFF Push “POWER·VOLUME” to turn the audio system on and off. Push “AM”, “FM1”, “FM2”, “AM·SAT”∗ or “DISC·AUX” to turn on that function with- out pushing “POWER·VOLUME”. You can turn on the compact disc player by inserting a compact disc. You can turn off the compact disc player by ejecting the compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the compact disc. If the radio was previously on, it will come on again. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.

SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1”, “FM2”, “AM·SAT”∗ or “DISC·AUX” if the system is already on but you want to switch from one function to other. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

radio, visit XM on

How to subscribe: You must enter into a separate service agreement with the XM radio in order to receive satellite broadcast programming in the vehicle. Additional activation and ser- vice subscription fees apply that are not included in the purchase price of the ve- hicle and optional digital satellite tuner. For complete information on subscription rates and terms, or to subscribe to the XM the web at www.xmradio.com or call an XM’s Listener Care at (800) 967−2346. The XM radio is solely responsible for the quality, availabil- ity and content of the satellite radio ser- vices provided, which are subject to the terms and conditions of the XM radio cus- tomer service agreement. Customers should have ID ready; the radio ID can be found by tun- ing to “channel 000” on the radio. For details, see “Displaying the radio ID” be- low. All fees and programming are the respon- sibility of the XM satellite radio and are subject to change.

radio

their

’07Camry hybrid_U (L/O 0610)

Satellite tuner technology notice: Toyota’s satellite radio tuners are awarded Type Approval Certificates from XM Satel- lite Radio Inc. as proof of compatibility with the services offered by the XM satel- lite radio. Displaying the radio ID Each XM tuner is identified with a unique radio ID. You will need the radio ID when activating XM service or when reporting a problem. If you select the “TUNE·FILE” knob, the ID code of 8 al- phanumeric characters appears. If you se- lect another channel, display of the ID code is canceled. The channel (000) alter- nates the display between the radio ID and the specific radio ID code. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.

“CH 000” using

the

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system.

license

license

symbol are

r (type 1 only)

technologies are from SRS

SRS The audio systems utilize SRS FOCUSr and SRS TruBassr audio enhancement technologies, under from SRS Labs, Inc., in all mode except AM radio mode. FOCUS, TruBass, SRS and trademarks of SRS Labs, Inc. FOCUS and TruBass incorporated under Labs, Inc. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange (type 2 only), and bass levels. In fact, different kinds of mu- sic and vocal programs usually sound bet- ter with different mixes of treble, midrange and bass. You can adjust sound characteristics. Dif- ferent sound characteristics can be re- corded for each audio source. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important.

183

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

8 cm (3 in.) compact disc singles Your compact disc player does not need an adaptor to play compact disc singles. Compact disc singles are about 8 cm (3
in.) than standard discs.

in diameter−smaller

NOTICE

Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs.

YOUR COMPACT DISC PLAYER WITH CHANGER (type 2) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. This compact disc play- er can store up to six discs. The player will play from track 1 through to the end of the disc. Then it will play from track 1 of the next disc. The player is intended for use with 12 cm (4.7 in.) discs only.

Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of other. YOUR RADIO ANTENNA Your vehicle has an antenna printed on the inside of the rear window.

NOTICE

Putting a film (especially a conductive or metallic film) on the rear window will noticeably reduce the sensitivity of the radio.

YOUR COMPACT DISC PLAYER (type 1) When you insert a disc, gently push it in with the label side up. The compact disc player will play from track 1 through to the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

184

NOTICE

z Do not stack up two discs for in- sertion, or it will cause damage to the compact disc player. Insert only one compact disc into slot at a time.

z Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Controls and features "Type 1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

185

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE·FILE” or “SEEK·TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM”, “FM1” or “FM2” button.)

(Eject button)

the compact disc eject button

Push eject a compact disc.

to

(Reverse/Fast forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the player will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CTRL (Tone and sound balance controls) Each time you push the “AUDIO CTRL” knob, the mode changes. To adjust the tone and balance, turn the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7.

186

the Speed Automatic

Switching over Sound Levelizer (ASL) level ASL: The Automatic Sound Levelizer can be turned on by turning the knob. In addi- tion, turning the knob allows you to select from LOW, MID, and HIGH volume and tone settings. The ASL system automati- cally adjusts volume and tone in accor- dance with the driving speed. DISC·AUX (Compact disc) Push compact disc. When the audio system is set to compact disc operation, the display shows the track number currently being played. To switch between CD and AUX (external device) modes, press “DISC·AUX” button. The AUX mode is only available when AUX adapter is connected to the system. When the AUX adapter is in use, “AUX” will appear on the display.

the “DISC·AUX” button

to play a

the

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of the separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of the separate unit is open. Close the compact disc changer lid. If “NO MUSIC” appears on the display, it indicates that a disc with no MP3/WMA data has been inserted. Remove the disc from the player and insert an MP3/WMA data disc. If the malfunction still exists, take your vehicle to your Toyota dealer.

Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. FM1 FM2
Push the “FM1” or “FM2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each of the preset button. FOLDER (Folder up/down) To skip up or down to a different folder: Push “Ɯ” or “Ɲ” side of the “FOLDER” several times until the number of the fold- er you want to listen to appears on the display. To jump to the first file in the first folder: Push and hold the “Ɲ” side of the button until you hear a beep. When playing a disc featuring both audio data (CD−DA) and MP3/WMA files, audio data (CD−DA) is played.

on

off.

and

in random order, or

POWER·VOLUME (Power and Volume) Push “POWER·VOLUME” to turn the audio system Turn “POWER·VOLUME” to adjust the volume. RAND (Random) Compact disc player There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

187

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

in a

the files

MP3/WMA player There are two random playback features— you can either listen to all of the files on the compact discs in random order. You can also listen to the files in a single folder in random order. To randomly play folder: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display. To randomly play all of the files on the compact disc: Push and hold “RAND” (preset button 1) ” will until you hear a beep. “ appear on the display and the player will play all of the files on the disc in random order. To turn off the random playback feature, push this button again.

the

track

RPT (Repeat) Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

file

the

MP3/WMA player There are two repeat features—you can repeat a signal file or an entire folder. Repeating a file: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the file ends, it will repeat automatically. This process will be continued until you push the button again to turn off the re- peat feature. Repeating a folder: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all of the files in the folder. When the last file in the folder ends, the folder will re- peat from the beginning. To turn off the repeat feature, push this button again.

188

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

listening

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a beep. “ SCAN” will appear on the dis- play and the first track on the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.

the player will scan

to. To select a

MP3/WMA player There are two scan features—you can ei- ther scan the files in a folder on a specif- ic disc or scan the first file of all the folder. Scanning the files on a folder: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the files in the folder you are listening file, push the “SCAN” again. After all the tracks on the disc have been scanned in one pass, nor- mal play resumes. Scanning the first file of all the folders: “SCAN” until you hear a beep. Push ” will appear on the display and “ the player will scan the first file of the next folder. To select a folder, push the “SCAN” again. After all the folders have been scanned in one pass, normal play resumes.

189

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

file

the

in the order

“TEXT” button while

MP3/WMA player This button is used to change the display for the MP3/WMA file that contains text data. To change the display, quickly push and release the MP3/WMA is playing. The display changes the elapsed time to folder name to file name to album title to track title to artist name, then back to the elapsed time. If is pushed while an MP3/WMA file that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire text data is not displayed, push and hold it until you hear a beep. The rest of the text data will appear.

this button

from

ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TEXT Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

to

of

or

up/

“Ɲ”

“Ɯ”

side

the seek mode,

(Seeking/Tracking

the radio finds and the next station up or down the

SEEK·TRACK down) Radio In plays station band. To seek the next station, quickly push and release the “SEEK·TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. Push the “SEEK·TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the beginning of track, quickly push the “Ɲ” side of the button one time. MP3/WMA player Use this button to file up or down to a different file. Push the “Ɯ” “SEEK·TRACK” several times until the file you want to listen to appears on the dis- play. If you want to return to the begin- ning of the current file, push the “Ɲ” side of the button one time.

the current

side

side

“Ɯ”

“Ɲ”

“Ɲ”

or

or

of

of

190

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

the

frequency. Turn

TUNE·FILE (Tuning and File up/down) Radio Turn the “TUNE·FILE” knob clockwise to the knob step up counterclockwise fre- quency. MP3/WMA player Turn the “TUNE·FILE” knob clockwise to file up. Turn the knob counterclockwise to file down.

to step down

the

’07Camry hybrid_U (L/O 0610)

191

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

"Type 2

192

’07Camry hybrid_U (L/O 0610)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE·FILE” or “SEEK·TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM·SAT”, “FM1” or “FM2” button.) XM satellite radio∗— These buttons are used tune in radio channels. To preset a channel to a button: Tune in the desired channel. (See “TUNE·FILE” or “SEEK·TRACK”.) Push and hold down the button until you hear a beep—this will set the channel to the button. The preset but- ton number will appear on the display.

to preset and

’07Camry hybrid_U (L/O 0610)

To recall a preset channel: Push the but- ton for the channel you want. The preset button number and channel number will appear on the display. This radio can store three XM channels for each button. (The display will show “SAT1”, “SAT2” or “SAT3” when you push “AM·SAT” button.) ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.

(Eject button)

This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.

(Reverse/Fast forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the player will resume playing. AM·SAT (AM band and XM satellite ra- dio∗) Push the “AM·SAT” button to turn on the radio and select the AM or XM band. “AM”, “SAT1”, “SAT2” or “SAT3” will ap- pear on the display. Error messages If tuner malfunctions, your audio system will display following error messages. “ANTENNA”: D The XM antenna

is not connected. Check whether the XM antenna cable is attached securely.

the satellite radio

D A short−circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer.

193

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

“UPDATING”: D You have not subscribed to

the XM satellite radio. The radio is being up- dated with the latest encryption code. Contact the XM satellite radio for sub- scription information. When a contact is canceled, you can choose the “CH000” and all free−to−air channels.

D The premium channel you selected is not authorized. Wait for about 2 sec- onds until the radio returns to the pre- vious channel or “CH001”. If it does not change automatically, select anoth- er channel. If you want to listen to the premium channel, contact the XM satel- lite radio.

is

“NO SIGNAL”: The XM signal too weak at the current location. Wait until your vehicle reaches a location with a stronger signal. “LOADING”: The unit is acquiring audio or program information. Wait until the unit has received the information. “OFF AIR”: The channel you selected is not broadcasting any programming. Select another channel.

194