2007 Toyota Camry HV Owners Manual

is available. Push the talk switch and say “Dial XXX (name you want to dial)”.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

To dial by Number 1. Push the talk switch and say “Dial by

Number”.

the

“Dial by number. Please push talk switch and say the number.” is heard and “Dial by Num” is displayed. 2. Push talk switch and say “XXXX”. “Push the off−hook switch to dial. Other- wise, push the talk switch and say dial, go back, or delete.” is heard. To dial the number, do the one of the following: D Push the off−hook switch. D Push the talk switch and say “Dial”. D Turn

“AUDIO CTRL” knob until “Dial” is displayed and push the knob. If the number exceeds 24 digits, the sys- tem may not function properly.

the

’07Camry hybrid_U (L/O 0610)

INFORMATION

D The system can recognize single digits from zero to nine, # (pound), ∗ (star) and + (plus). Numbers that are ten or greater are not recog- nized.

D To speed up input, it is a good idea to group all digits into a continuous string. However, you can enter each digit individually or group digits to- gether in preferred string lengths.

The display corresponding to each op- eration appears on the screen as fol- lows: Input operation— You say: “Nine, nine, five” Voice output: “995 push the off−hook switch to dial. Otherwise, push the talk switch and say dial, go back, or delete.” Display: “995” You say: “Seven, three, four” Voice output: “734 push the off−hook switch to dial. Otherwise, push the talk switch and say dial, go back, or delete.”

the

Display: “995734” Repeat the above procedure until the entire number that you want to dial is input. Go back operation— You say: “Go back” Voice output: “Go back, the last num- bers entered have been removed. Push talk switch and continue adding numbers otherwise say dial, go back, or delete.” Display: “995” Repeating the above operation deletes the last digits in reverse order of in- put. Delete operation— You say: “Delete” Voice output: “Deleted. The entire number to dial has been deleted. Please push the talk switch and say the number.” Display: “Dial by Num” The display will return to the initial screen that allows a number to be input.

237

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Cancel operation— Do either one of the following: D Push the on−hook switch at anytime

during the operation.

D Push the talk switch and say “Can- cel” after the beep at anytime dur- ing the operation except while a call is connected.

—Receiving a phone call When receiving a phone call, a ring tone is audible and the system changes into the telephone mode. When receiving a phone call, the display is as follows. The display differs depend- ing on whether or not the vehicle is in motion. When the vehicle is stopped: Number, name or “Incoming” is displayed. When the vehicle is in motion: “Incoming” is displayed. Do either one of the following: D Pushing the off−hook switch allows you

to talk on the phone.

D Pushing the call.

the on−hook switch

refuses

To transfer a call to the phone: The received call can be transferred from the hands−free system the cellular phone that is connected to Bluetoothr. For details, refer to the user’s guide for the cellular phone.

to

To adjust the ring volume, push “+” or “−” on the steering volume controls. Volume adjustment cannot be done using the au- dio system. Repeatedly pushing “−” on volume controls mutes the ring. When international phone call, the name of the party may not be displayed correctly depending on the cellu- lar phone.

receiving an

the steering

238

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

To transfer a call from the phone: Pushing the off−hook switch while talking on the cellular phone that is connected to Bluetoothr allows you to talk hands−free. To transfer a call to the phone: The call can be the hands−free system to the phone that is connected to Bluetoothr. For details, refer to the user’s guide for the cellular phone.

transferred

from

—Talking on the phone While talking on the phone, the display is as follows. The display differs depending on whether or not the vehicle is in motion. When the vehicle is stopped: Number is displayed. When the vehicle is in motion: “Talking” is displayed. When the call is finished, push the on− hook switch. In the following situations, your voice may not reach the party. D Talk alternately with the other party on the same the voice may not reach each

the phone. time, other. (It is not a malfunction.)

talk at

If you

D Keep

the volume of

receiving voice down. Otherwise, echo is coming up. When you talk on the phone, speak clearly towards the microphone. D When driving on a rough road. D When driving at high speeds. D When the window is open. D When the air conditioning vents face

the microphone.

D When the sound of the air conditioning

fan is loud.

239

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 9

OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Automatic air conditioning system

Controls Air flow selector settings Operating tips

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Climate remote controls Side and rear vents Air conditioning filter

241
246
246
249
250
251

240

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Automatic air conditioning system— —Controls

1. Temperature selector (“TEMP”)

(with “DUAL” button indicator on—individual setting on driver side only) (with “DUAL” button indicator off—simultaneous setting on driver and front passenger)

2. Fan speed selector 3. Air flow selector button 4. Temperature selector (“PASS TEMP”) (individual setting on front passenger side only)

5. “A/C” button 6. Air intake selector 7. Windshield air flow button 8. “OFF” button 9. “AUTO” button

241

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the

“AUTO” button For automatic operation of the air condi- tioning, press “AUTO” button. The “AUTO” button will turn on, indicating that the automatic operation mode has been selected. In the automatic operation mode, the air conditioning selects the most suitable fan speed, air flow, air intake and on−off of the air conditioning according to the tem- perature. When you press the “AUTO” button with the air intake mode at FRESH, internal circulation may be applied for maximum cooling. You may use manual controls if you want to select your own settings. Fan speed selector Push the “Ɯ” (increase) or “Ɲ” (decrease) side of the button to adjust the fan speed. In automatic operation, you do not have to adjust the fan speed unless you desire another fan speed mode.

242

the

for driver and

the knob to adjust

indicator off—Simultaneous front

“DUAL” button Push the button to change the mode of the temperature setting. With the indicator on—Individual temper- ature setting for driver and front passen- ger With temperature setting passenger Temperature selectors Turn the temperatu- re—to the right to warm, to the left to cool. “LO” appears when you adjust to maxi- mum cooling, and “HI” appears when you adjust to maximum warming. —“TEMP” knob With the “DUAL” button indicator on—This knob changes the temperature on the driv- er side only. With the “DUAL” button indicator off—This knob changes the temperature on the driv- er side and front passenger side simulta- neously. This function will be cancelled when the “PASS TEMP” knob is turned. —“PASS TEMP” knob This knob changes the temperature on the front passenger side only.

“OFF” button Push the button to turn off the air condi- tioning system.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

4. Floor/Windshield—Air

the

flows mainly floor vents and windshield

from vents. This position allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. If you want to return the setting to RECIRCULATE mode, press the air in- take selector button once again. Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly.

is pressed, air

this button from

this button once again returns

Windshield air flow button flows When the windshield vents and mainly turns on the defogging function with the purpose of clearing the front view. Pressing the air flow mode to the last one used. This button allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. It is not pos- sible to return to RECIRCULATE in this mode. Press for dehumidified heating or cooling. This setting clears the front view more quickly. For details about air flow selector settings, see flow selector settings” de- scribed below. When the “POWER” switch is set at ON after the 12 volt battery is reconnected, the indicator light on the button may flash and a motor sound may be heard. This does not indicate a malfunction.

the “A/C” button

“—Air

243

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Air flow selector button Push the button to select the vents used for air flow. In automatic operation, you do not have to select the air flow unless you desire another air flow mode. 1. Panel—Air

flows mainly

from

the the rear

instrument panel vents and vents.

2. Bi−level—Air flows from both the floor vents, the instrument panel vents and the rear vents.

3. Floor—Air flows mainly from the floor

vents.

’07Camry hybrid_U (L/O 0610)

“A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. If the “A/C” button indicator flashes, there is a problem in the air conditioning system and the air conditioning automatically shuts off. If this happens, take your ve- hicle to a Toyota dealer for service.

PlasmaclusterTM∗ The PlasmaclusterTM∗ helps to keep good air quality in the cabin by emiting positive and negative ions into the cab- in. Operating the air conditioning system al- lows positive and negative ions to come out from the driver’s side vent. A low noise may be heard during opera- tion. This is not a malfunction. Static electricity may be discharged near the driver’s side vent because high volt- age is used to operate the system. To clean the driver’s side vent, wipe the vent using a soft cloth after turning the system off.

CAUTION

Do not disassemble or repair the sys- tem because it contains high voltage parts. Call your Toyota dealer if the system needs repair.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Air intake selector Press the button to select the air source. 1. RECIRCULATE (indicator light is on)— Recirculates the air inside the vehicle. is off)—Draws

2. FRESH (indicator light

outside air into the system.

To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system.

244

’07Camry hybrid_U (L/O 0610)

NOTICE

Do not insert anything into the driv- er’s side vent, attach anything to it, or use sprays around the driver’s side vent. These things may cause the sys- tem not to work properly.

∗: This system adopts the plasmacluster technology, manufactured under license from SHARP Corporation. “PlasmaclusterTM” is a trademark of SHARP Corporation.

The “ECO HEAT/COOL” mode is canceled in the following cases: D The temperature control is set at “LO” (the lowest temperature) or “HI” (the highest temperature).

D The air flow is set in the floor/wind-

shield mode or windshield mode.

D “ECO HEAT/COOL” switch

is pushed

again.

the “ECO HEAT/COOL” switch

“ECO HEAT/COOL” switch Push to select the “ECO HEAT/COOL” (economi- cal) mode of the air conditioning. The indi- cator on the switch comes on and “ECO” appears on the air conditioning display to indicate that the mode is on. The efficiency of the air conditioning is limited because the consumption of elec- tricity is reduced, achieving a reduction of fuel consumption. As a result, it may take longer than the usual amount of time for the inside air temperature to reach the set temperature.

245

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

—Air flow selector settings

246

’07Camry hybrid_U (L/O 0610)

—Operating tips D To cool off your Toyota after

it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.

D Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).

D On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.

D Keep the area under the front seats clear to allow air to circulate through- out the vehicle.

for a minute

D On cold days, set the fan speed to high the intake ducts of snow or moisture. This can reduce the amount of fogging on the windows.

to help clear

D When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

D If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.

Heating For best results, set controls as follows: For automatic operation—

Air conditioning For best results, set controls as follows: For automatic operation—

Press in the “AUTO” button. Temperature—To the desired

temperature

Air intake—FRESH (outside air) Air conditioning—OFF

Press in the “AUTO” button. Temperature—To the desired

temperature

Air intake—FRESH (outside air) Air conditioning—ON

For manual operation—

For manual operation—

Fan speed—To the desired fan speed Temperature—Towards WARM Air intake—FRESH (outside air) Air flow—FLOOR Air conditioning—OFF

Fan speed—To the desired fan speed Temperature—Towards COLD Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON

for a

few minutes. To keep

D For quick heating, select recirculated air the windows from fogging, select fresh af- ter the vehicle interior has been war- med.

D Press the “A/C” button on for dehumidi-

fied heating.

D Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.

D For quick cooling, select recirculated

air for a few minutes.

247

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Ventilation For best results, set controls as follows: For automatic operation—

Press in the “AUTO” button. Temperature—Towards low temperature Air intake—FRESH (outside air) Air conditioning—OFF

For manual operation—

Fan speed—To the desired fan speed Temperature—Towards COLD Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF

248

Defogging and defrosting —The inside of the windshield For best results, set controls as follows: —For automatic operation

Temperature—Towards high temperature to heat; low temperature to cool

Air intake—FRESH (outside air) Air flow—WINDSHIELD

—For manual operation

Fan speed—To the desired fan speed Temperature—Towards high temperature to heat; low temperature to cool

Air intake—FRESH (outside air) Air flow—WINDSHIELD

the windshield air

Pressing flow button turns on the defogging function with the purpose of clearing the front view. When pressing the windshield air flow but- ton, the air intake selects FRESH auto- matically. This is to clean up the front view more quickly. It is not possible to return to RECIRCULATE in this mode.

the “A/C” button

Press for dehumidified heating or cooling. This setting clears the front view more quickly. D On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.

—The outside of the windshield For best results, set controls as follows: —For automatic operation

Temperature—Towards high temperature Air intake—FRESH (outside air) Air flow—WINDSHIELD

—For manual operation

Fan speed—To the desired fan speed Temperature—Towards high temperature Air intake—FRESH (outside air) Air flow—WINDSHIELD

the windshield air

flow button Pressing turns on the defrosting function with the purpose of clearing the front view. When pressing the windshield air flow but- ton, the air intake selects FRESH auto- matically. This is to clean up the front view more quickly. It is not possible to return to RECIRCULATE in this mode.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Climate remote controls (steering switches)

the “A/C” button

Press for dehumidified heating or cooling. This setting clears the front view more quickly. D To heat the vehicle interior while de- choose

windshield,

frosting floor/windshield air flow.

the

Some parts of the air conditioning system can be adjusted using the switches on the steering wheel. Details of the specific switches, controls, and features are described below. 1. Temperature selector (“TEMP”)

(with “DUAL” button indicator on—individual setting on driver side only) (with “DUAL” button indicator off—simultaneous setting on driver and front passenger)

2. “AUTO” button 3. “OFF” button

the

“AUTO” button For automatic operation of the air condi- tioning, press “AUTO” button. The “AUTO” button will turn on, indicating that the automatic operation mode has been selected. In the automatic operation mode, the air conditioning selects the most suitable fan speed, air flow, air intake and on−off of the air conditioning according to the tem- perature. When you press the “AUTO” button with the air intake mode at FRESH, internal circulation may be applied for maximum cooling. You may use manual controls if you want to select your own settings. Temperature selector To the “Ɯ” side. To decrease it, press the “Ɲ” side. “LO” appears when you adjust to maxi- mum cooling, and “HI” appears when you adjust to maximum warming. With the “DUAL” button indicator on—This button changes the driver side only.

temperature, press

temperature on

increase

the

the

249

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

the

temperature on

With the “DUAL” button indicator off—This button changes the driver side and front passenger side si- multaneously. This function will be cancelled when the “PASS TEMP” knob on the instrument pan- el is turned. “OFF” button Push the “OFF” button to turn off the air conditioning system.

’07Camry hybrid_U (L/O 0610)

Side and rear vents

If air flow control is not satisfactory, check the side and rear vents. The side and rear vents may be opened or closed as shown.

Side vents

Rear vents

250

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Air conditioning filter—

The air conditioning filter information label is placed inside of the glove box as shown and indicates that a filter has been installed. The air conditioning filter prevents dust from entering the vehicle through the air conditioning vent.

The air conditioning filter is behind the glove box.

—Checking, cleaning and replacing the air conditioning filter The air conditioning filter may clog af- ter long use. The filter may need to be cleaned or replaced if the air flow of the air conditioning and heater experi- ences extreme reductions in operating efficiency, or if the windows begin to fog up easily in FRESH mode. To maintain the air conditioning efficiency, inspect, clean and replace the air condi- tioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, such as inner city or desert areas, early replacement may be required. (For scheduled maintenance in- formation, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

251

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

1. Open the glove box, and slide off

the damper as shown.

2. Apply pressure to the glove box as

shown to disengage the claws.

3. Remove the filter cover while push-

ing in both ends of the cover.

252

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

4. Pull the filter out of the filter outlet.

Inspect the filter on the surface.

If it is dirty, it should be cleaned or re- placed.

To clean the filter, blow compressed air through it from the bottom. Hold the air gun 50 mm (2 in.) from the filter and blow for approximately 2 minutes at 500 kPa (5.0 kgf/cm2 or bar, 72 psi). If is not available, have filter cleaned by your Toyota dealer.

the

it

When inserting the filter in the filter outlet, keep the arrow pointing up.

NOTICE

To prevent damage to the air condi- tioning system, do the following. z When using

the air conditioning system, make sure that a filter is always installed. z When cleaning

filter, do not

the

clean the filter with water.

253

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 10

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Trip information Clock Compass Power outlets Garage door opener Portable ashtray Glove box Auxiliary boxes Rear console box Front cup holder Rear cup holder Grocery bag hooks Cargo net Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

255
257
258
262
263
266
267
268
270
270
271
271
272
272

254

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Trip information (with navigation system)

’07Camry hybrid_U (L/O 0610)

CAUTION

Do not operate the screen while the vehicle is moving. Be sure to operate the screen only when the vehicle is stopped.

1. Push the “INFO” button to display

the “Information” screen.

2. Touch the “Trip information” on the

screen.

the

instrument panel

Trip information appears on the screen. When lights are turned on, the brightness of the screen will be reduced. You can adjust the screen. To adjust the brightness, see the “Navigation System Owner’s Manual” for the procedure.

the brightness of

255

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

information

listed above

The is dis- played when you touch the “Consump- tion” switch on the “Energy Monitor” screen. The displayed values on the screen indi- cate general driving conditions. Accuracy varies with driving habits and road condi- tions. When the “POWER” switch is set at ON, the last previously used mode displayed just before the “POWER” switch is turned off will appear. If “Reset All” is touched, all of the graph- ics and values except the cruising range will be reset. If the electrical power source is discon- nected from the navigation system screen, the screen will automatically be set to the initial mode. 1. Fuel consumption

the past 30

in

minutes (“Consumption”)

The transition of fuel consumption in the past 30 minutes is displayed in the graph.

Consumption screen

1. Transition of fuel consumption in the

past 30 minutes

2. Regenerated energy

in

the past 30

minutes

3. Best fuel economy among average 4. Cruising range 5. Average fuel consumption

256

2. Regenerated energy in the past 30

minutes

The regenerated energy in the past 30
minutes is indicated with symbols. One symbol indicates 50 Wh. Up to 4
symbols will be shown. The energy of 50
Wh illuminates a 50 W bulb for an hour. 3. Best fuel economy (lowest fuel con-

sumption) among average (“Best”)

Best fuel economy among average is displayed. If the average fuel consumption is reset by touching the “Reset” and the average fuel consumption is the lowest, the value is overwritten. 4. Cruising range

(“Cruising Range”)

fuel

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The cruising range display indicates the approximate distance that you can drive until is different from the actual distance traveled. If the fuel gauge malfunctions, the mileage figure will not appear.

fuel gauge reaches “E”.

the

It

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Clock

When the vehicle is refueled, the driving range is recalculated. The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer than indicated. If fuel consumption is poor, the driving range will be shorter than indicated. If the low fuel level warning light comes on, refuel the vehicle even if the display indicates that the vehicle can be driven further. 5. Average fuel consumption

(“Average”)

Average fuel consumption is displayed based on total driving distance and to- tal fuel consumption. The calculation is reset by touching the “Reset”. If the average fuel consumption is the lowest, the value of the best fuel economy among average is overwritten.

Energy Monitor screen

the screen the energy. See

Touching the “Energy” switch turns on the “Energy Monitor” that displays the hybrid system operating condition. the The arrow on indicates movement of “Energy monitor” on page 3 for the representative screen. The segments of the screen indicate the status of the hybrid battery. See “—Hybrid battery status” on page 5 for details.

the battery on

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The “POWER” switch must be set at ACC or ON. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock). When lights are turned on, the brightness of the time indi- cator will be reduced.

instrument panel

the

257

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Compass

D The vehicle is magnetized. (There is a magnet or a metal object on or near the inside rear view mirror.)

D The 12 volt battery has been discon-

nected.

the deviation

If your vehicle is out of the set zone, refer to “CALIBRATING THE COMPASS” below to set the zone number. If the compass works to calibrate the direction automati- cally while the vehicle is in motion. For additional precision or calibrating, see COMPASS” below.

for complete THE

“CALIBRATING

is small,

Displays

NE SE SW NW

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct direction in the following conditions: D The vehicle is stopped immediately af-

ter turning.

D The compass does not adjust while the

vehicle is stopped.

D The “POWER” switch is turned off im-

mediately after turning.

D The vehicle is on an inclined surface. D The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

turn back on when

The direction is indicated on the inside rear view mirror. If the “POWER” switch was turned off with the system on, the system will automati- cally the “POWER” switch is turned on. Push the “AUTO” switch for longer than 3
seconds to turn the compass system on and off. the direction The compass that the above case, it shows that the vehicle is heading north.

is heading.

the vehicle

indicates

In

258

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

The compass sensor is in the inside rear view mirror.

NOTICE

Do not put magnets or a metal object on or near the inside rear view mirror of the vehicle. Doing this may cause malfunction of the compass sensor.

the

from

CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on true direction deter- deviates mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, then push and hold the switch until the zone number appears on the display. Then push the switch, referring to the fol- lowing map to select the number of the zone where the vehicle is.

259

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Samoa: 5

Guam:

Saipan: 8

After calibration, leaving the system for several seconds returns it to the compass mode.

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Zone numbers

260

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the direction display on

CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. To rectify this, stop the vehicle and push and hold the switch until “C” appears on the display. If “C” appears on the display because of a drastic change in the magnetic field, perform circling calibration.

in a circle, drive around

Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space to drive the block. After driving 1 to 3 circles in the above method, calibration is completed when the direction is shown on the display. If calibration cannot be performed because of the magnetized vehicle etc., take your vehicle to Toyota dealer.

Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the 12 volt battery has been re- moved, replaced or disconnected. D Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

in a place where

D During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.

261

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

D When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

D Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Power outlets

Front console

262

Center console

’07Camry hybrid_U (L/O 0610)

for

The power outlets are designed power supply for car accessories. The “POWER” switch must be set at ACC or ON for the power outlet to be used. Front console power outlet—Connected cables can be passed through the hole to the front passenger side of the auxiliary box. For details, see “Auxiliary boxes” on page 268 in this Section.

NOTICE

the

fuse

z To prevent

from being blown, do not use the electricity over the total vehicle capacity of 12V/120W.

z To prevent the 12 volt battery from being discharged, do not use the power outlets longer than necessary when the hybrid system is turned off.

z Close the power outlet

lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Garage door opener

Buttons

Indicator light

The garage door opener ( Universal Transceiver) is manufactured under license from HomeLinkR and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.

transmitter prior

(a) Programming the HomeLinkR The HomeLinkR in your vehicle has 3
buttons and you can store one program for each button. To ensure correct programming into the HomeLinkR, install a new battery in the hand−held to program- ming. The battery side of the hand−held trans- mitter must be pointed away the HomeLinkR during the programming pro- cess. For Canadian users, follow the procedure “Programming an entrance gate/pro- in gramming all devices the Canadian market”. 1. Decide which of 3 HomeLinkR buttons

from

in

you want to program.

HomeLinkr

25 to 75 mm (1 to 3 in.)

Hand−held garage transmitter

2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLinkR.

Keep the indicator light on the HomeLinkR in view while programming.

263

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

6. Repeat steps 2 through 5 for each re- maining HomeLinkR button to program another device.

3. Simultaneously press and hold

the hand−held garage transmitter button along with the selected HomeLinkR but- ton.

Do not release the buttons until step 4
has been completed. 4. When

the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

indicator

the

264

5. Test the operation of the HomeLinkR by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes.

If the garage door does not operate, iden- tify if your garage transmitter is of the “Rolling Code” type. Press and hold the programmed HomeLinkR button. The ga- rage door has the rolling code feature if the HomeLinkR) the flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the “Rolling Code” type, proceed to the heading “Programming a rolling code sys- tem”.

indicator

light

(on

it

is

to

is necessary

Programming a rolling code system “Rolling Code” If your device equipped, follow steps 1 through 4 under the heading “Programming the HomeLinkR” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.

location and color of

to

2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLinkR button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.

If

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

now

should

recognize

The ceiling mounted garage door opener motor the HomeLinkR unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLinkR button to program another rolling code system.

Programming an entrance gate/program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLinkR but-

2. Place

your

tons you want to program. hand−held

gate/device transmitter 25 to 75 mm (1 to 3 in.) away the HomeLinkR.

surface

from

the

of

Keep the indicator light on the HomeLinkR in view while programming. 3. Press

selected

hold

and

the

HomeLinkR button.

4. Continuously press and release (cycle) transmitter the hand−held gate/device button every two seconds until step 5
is complete. the

the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

5. When

indicator

’07Camry hybrid_U (L/O 0610)

6. Test the operation of the HomeLinkR by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.

7. Repeat steps 1 through 6 for each re- maining HomeLinkR button to program another device.

Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLinkR buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLinkR”. (b) Operating the HomeLinkR To operate the appropriate HomeLinkR button to activate the programmed device. The HomeLinkR indicator light should come on. The HomeLinkR continues to send the signal for up the button is pressed.

the HomeLinkR, press

to 20 seconds as

long as

(c) Erasing

the

entire HomeLinkR

memory (all three programs)

To erase all previously programmed codes at one time, press and hold down the 2
outside buttons for 20 seconds until the indicator light flashes. If you sell your vehicle, be sure to erase the HomeLinkR the programs stored memory. For additional programming assistance Universal with Transceiver call the: D Toyota Customer Experience Center at

HomeLinkR

your

in

1−800−331−4331 (U.S.A.)

D Toyota Canada Customer

Interaction

Centre at 1−888−869−6828 (Canada)

265

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Portable ashtray

received,

This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.

including

Refer to HomeLinkR on the internet at: WWW.HOMELINK.COM

CAUTION

D When programming the HomeLinkR Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.

D Do not use this HomeLinkR Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.

266

The ashtray can be removed and used outside the vehicle. To use the ashtray, raise the lid. finished with your cigarette, thor- When oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, close the lid completely. The cup holder lid cannot be closed while the ashtray is installed. To detach the ashtray, pull it out.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Glove box

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, always completely close the ashtray after use.

injury

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

To use the glove box: Open by pulling the lever. Lock by inserting the mechanical key and turning it clockwise. Unlock by and turning it counterclockwise. With the instrument panel lights on, the glove box light will come on when the glove box is open.

inserting the mechanical key

267

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Auxiliary boxes

268

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

To use the boxes, open it as shown the illustration. 1. Driver’s side instrument panel 2. Overhead console 3. Front console

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

injury

NOTICE

Overhead console box—During hot weather, the interior of the vehicle becomes very hot. Do not leave any- thing flammable or deformable such as a lighter, glasses, etc. inside.

’07Camry hybrid_U (L/O 0610)

CABLE PASS−THROUGH The auxiliary box of the front console is provided with a hole that allows cables to be passed into the cabin from the inside power outlet and AUX adapter. To open the hole, perform the following procedure: 1. Remove the lid on the inside of the

auxiliary box.

2. From the inside of the auxiliary box,

push out and remove the outer lid.

Be careful not to lose the removed lids.

269

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Rear console box

Front cup holder

To open the console box, push the lock release button and raise the console box lid. The upper tray slides forward/backward and can be removed.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

The cup holder is designed for holding cups or drink−cans securely. To use them, open it as shown in the illustra- tion. The adapter for front cup holder is detach- able. Replace its original position when using the front cup holder. Other- wise the drinks will not be held securely.

in

it

270

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.

’07Camry hybrid_U (L/O 0610)

Rear cup holder

Grocery bag hooks

This hook is designed to hang things like grocery bags.

NOTICE

To prevent damage to the hook, avoid hanging heavy loads on it.

The cup holder is designed for holding cups or drink−cans securely. To use it, pull down the armrest.

CAUTION

D Do not place anything else other than cups or drink−cans in the cup holder, as such items may be thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D Do not lift the armrest upright when

the cup holder is in use.

271

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Cargo net

Floor mat

Use a floor mat of the correct size. If the vehicle carpet and floor mat have two holes, then they are designed for use with locking clips. Attach the floor mat to the vehicle carpet using the clips. Lock the clips the vehicle carpet.

the holes

into

in

To secure belongings, hang the cargo net on the hooks.

NOTICE

z Do not use the net to secure sharp or heavy objects. The net will tear off.

z Be sure not to twist the net when

hooking.

272

CAUTION

Make sure the floor mat is properly placed on the vehicle carpet. If the floor mat slips and interferes with the movement of the pedals during driv- ing, it may cause an accident.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

273

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 2

INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Break−in period Fuel Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Electric power steering system Brake pad wear limit indicators Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

275
275
277
277
278
279
280
281
282
282
283
284
284
285
295
295
298

274

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: D Avoid full

throttle acceleration when

starting and driving.

D Avoid racing the hybrid system. D Try to avoid hard stops during the first

300 km (200 miles).

D Do not drive for a long time at any

single speed, either fast or slow.

D Do not tow a trailer during the first 800

km (500 miles).

Fuel FUEL TYPE Your new vehicle must use only un- leaded gasoline. To help prevent gas station mix−ups, your Toyota has a smaller fuel tank opening. The special nozzle on pumps with un- leaded fuel will fit it, but the larger stan- dard nozzle on pumps with leaded gas will not. At a minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.

NOTICE

Do not use leaded gasoline. Use of leaded gasoline will cause the three− way catalytic converter to lose its ef- fectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

OCTANE RATING Select Octane Rating 87 (Research Oc- tane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. If your engine knocks... If you detect heavy knocking even when using if you hear steady knocking while holding a steady speed on level roads, consult your Toyota dealer. However, occasionally, you may notice light knocking for a short time while accel- erating or driving up hills. This is normal and there is no need for concern.

the recommended

fuel, or

275

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

CLEANER BURNING GASOLINE Cleaner burning gasoline, including re- formulated gasoline that contains oxy- genates such as ethanol or MTBE is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gas- oline provide excellent vehicle perfor- mance, reduce vehicle emissions, and im- prove air quality. OXYGENATES IN GASOLINE Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.

If you use gasohol

GASOLINE CONTAINING MMT Some gasoline contain an octane en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel con- taining MMT is used, your emission con- trol system may be adversely affected. The Malfunction Indicator Lamp on the in- strument cluster may come on. If this hap- pens, contact your Toyota dealer for ser- vice. GASOLINE QUALITY In a very few cases, you may experience driveability problems caused by the partic- ular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer.

in

GASOLINE CONTAINING DETERGENT ADDITIVES Toyota recommends the use of gasoline that contains detergent additives to avoid build−up of engine deposits. However, all gasoline sold the U.S. contains detergent additives to keep clean and/or clean intake systems. QUALITY GASOLINE Automotive manufacturers in the U.S., Europe and Japan have developed a specification fuel named World−Wide Fuel Charter (WWFC) that is expected to be applied world wide. The WWFC consists of four categories that depend on required emisvels. In the U.S., category 4 has been adopted. The WWFC improves air quality by pro- viding for better emissions in vehicle fleets, satisfaction through better vehicle performance.

for quality

customer

and

276

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

NOTICE

z Do not use gasohol other

than stated above. It will cause fuel sys- tem damage or vehicle performance problems.