2001 Toyota 4runner Owners Manual

viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1·2”, “TAPE” or “CD” if the system to switch from one function to another.

is already on but you want

that

’01 4Runner_U (L/O 0008)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA Your vehicle has a mast type antenna. Detachable antenna To remove an detachable antenna, careful- ly turn it counterclockwise.

NOTICE

To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.

Power antenna To lower a power antenna, turn off the audio system by pushing “PWR·VOL” or “PWR/VOL”, or to “LOCK”. The power antenna automatically retracts when the radio mode is switched off to turn on the cassette tape player.

turn the ignition key

NOTICE

To prevent damage to the antenna, make sure it is retracted before driv- ing your Toyota through an automatic car wash.

2001 4RUNNER (OM35768U)

131

’01 4Runner_U (L/O 0008)

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

132

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

—Controls and features "Type 1

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

2001 4RUNNER (OM35768U)

133

’01 4Runner_U (L/O 0008)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature.

fast

the

the

Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CTRL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For “CTRL appears on knob to suit your preference. The display will show the “BAS −5” to “BAS 5”.

tone adjustment, push / MODE” repeatedly until “BAS” the

the display. Then

to adjust

low−pitch

is used

range

turn

from

tone

134

2001 4RUNNER (OM35768U)

from

turn

range

to adjust

is also used

the display. Then

tone adjustment, push / MODE” repeatedly until “TRE” the

For high−pitch “CTRL appears on knob to suit your preference. The display will show the “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CTRL / MODE” repeatedly until “FAd” appears on the display. Then turn the knob to adjust the front/rear balance. The display will show “FAd−F7” to “FAd−R7”. For MODE” repeatedly until “BAL” appears on the display. Then turn the knob to adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”.

left/right adjustment, push “CTRL

range

range

from

from

the

the

’01 4Runner_U (L/O 0008)

time you push “CD”,

CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.

inserted up−side down. Clean

loaded

inside

it the

is

2001 4RUNNER (OM35768U)

If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape.

B NR∗

135

∗

: Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the are trademarks of Dolby Laboratories double D symbol Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR/VOL (Power/Volume) Push “PWR/VOL” to turn the audio system on and off. Turn “PWR/VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order.

listen

the

to

’01 4Runner_U (L/O 0008)

the

in the

random

turn off

To randomly play the tracks on a disc: Quickly push and release “RAND”. “RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To feature, push “RAND” again. Compact disc auto changer only— To randomly play all the tracks magazine: Push and hold “RAND” until you hear a ·RAND” will appear on the dis- beep. “ play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push “RAND” again. RPT (Repeat) Cassette Player is playing. Push “RPT” while “RPT” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

track ends,

track

the

Compact Disc Player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a ·RPT” will appear on the dis- beep. “ play. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back the disc and replay. This process will be continued until you push the button again to turn off the repeat feature.

to the top track of

136

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again. Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine.

Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push the display “ and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station.

the radio finds and the next station up or down the

·SCAN” will appear on

the seek mode,

“SCAN” again.

If

Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

2001 4RUNNER (OM35768U)

137

’01 4Runner_U (L/O 0008)

TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.

138

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

"Type 2

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

2001 4RUNNER (OM35768U)

139

’01 4Runner_U (L/O 0008)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

140

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

the

from

from

range

range

the knob

the knob

the display. Then

the display. Then

For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.

time you push “CD”,

inserted up−side down. Clean

If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.

loaded

inside

it the

is

2001 4RUNNER (OM35768U)

141

the

tone

from

range

is used

low−pitch

to adjust

/ MODE”

CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. For middle−pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.

the display. Then

is also used

/ MODE”

to adjust

range

turn

from

the

’01 4Runner_U (L/O 0008)

B NR∗

DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button.

If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: ” Quickly push and release “ will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again.

listen

the

”. “

to

in the

Compact disc auto changer only— To randomly play all the tracks magazine: ” until you hear a Push and hold “ ” will appear on the dis- beep. “ play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again. RPT (Repeat) Cassette Player ” while the track is playing. Push “ ” will appear on the display. When “ the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

142

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: ” while the Quickly push and release “ track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: ” until you hear a Push and hold “ beep. “ ” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push the display “ and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning.

·SCAN” will appear on

“SCAN” again.

If

2001 4RUNNER (OM35768U)

143

’01 4Runner_U (L/O 0008)

the seek mode,

the radio finds and the next station up or down the

SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

144

2001 4RUNNER (OM35768U)

TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

’01 4Runner_U (L/O 0008)

"Type 3

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

2001 4RUNNER (OM35768U)

145

’01 4Runner_U (L/O 0008)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button)

the cassette

tape eject button to

Cassette tape Push eject a cassette. After you turn the ignition to “LOCK”, you will be able to eject a cassette, but you will not be able to reinsert it.

Compact disc To eject one compact disc only: Push and release the compact disc eject button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for ejecting all the discs loaded in the changer. You can also eject any spe- cific one of the discs loaded in the chang- er as follows:

1. Push either side of the “DISC” button until the number of the disc you want to eject is displayed.

2. Push and release the compact disc

eject button.

To eject all the discs loaded in the chang- er: Push and hold the compact disc eject button (until you hear a beep when the audio system is on). The last compact disc played before pushing the button will be ejected first. If a disc is left in the slot for a long time, the function to eject all the discs will be automatically cancelled. After you turn the ignition to “LOCK”, you will be able to eject one compact disc only or all the discs loaded in the chang- er, but you will not be able to reinsert it or them.

146

2001 4RUNNER (OM35768U)

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

’01 4Runner_U (L/O 0008)

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

the

tone

from

range

is used

low−pitch

to adjust

/ MODE”

CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. For middle−pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.

the display. Then

is also used

/ MODE”

to adjust

range

turn

from

the

the

from

from

range

range

the knob

the knob

the display. Then

the display. Then

For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. If the player or another unit equipped with the player malfunctions, your audio system will display one of the six following error messages.

2001 4RUNNER (OM35768U)

147

’01 4Runner_U (L/O 0008)

LOAD This button is used to load the compact discs in the compact disc auto changer which is integrated with the radio and cas- sette player. This compact disc auto changer can store up to 6 discs. The key must be in the “ACC” or “ON” position. Loading one compact disc only— To load one compact disc only, quickly push and release the button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for loading multiple compact discs. After pushing the button, insert a compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. If no compact disc is inserted, the shutter will close after 15 seconds.

B NR∗

Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation.

2001 4RUNNER (OM35768U)

is

it the

inside

loaded

inserted up−side down. Clean

If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC ƝƜ By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. 148

Loading multiple compact discs— To load multiple compact discs, push and hold (until you hear a beep when the au- dio system is on). After pushing the but- ton, insert the first compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. After a few seconds, the shutter will automatically open again so the next disc can be in- serted. The same process can be applied for loading the rest of the discs. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order.

listen

the

to

’01 4Runner_U (L/O 0008)

”. “

To randomly play the tracks on a disc: ” Quickly push and release “ will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again. To randomly play all magazine: ” until you hear a Push and hold “ beep. “ ” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again.

the tracks

in the

RPT (Repeat) Cassette Player

” while the track

is playing. Push “ “ ” will appear on the display. When the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: ” while the Quickly push and release “ track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature.

2001 4RUNNER (OM35768U)

149

’01 4Runner_U (L/O 0008)

Repeating a disc: ” until you hear a Push and hold “ ” will appear on the display. beep. “ The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again.

To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again. Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning.

150

2001 4RUNNER (OM35768U)

If

“SCAN” again.

the seek mode,

Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push ·SCAN” will appear on the display “ and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display.

the radio finds and the next station up or down the

’01 4Runner_U (L/O 0008)

TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.

Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side.

2001 4RUNNER (OM35768U)

151

’01 4Runner_U (L/O 0008)

Car audio system operating hints

NOTICE

To ensure the correct audio system operation: z Be careful not to spill beverages

over the audio system.

z Do not put anything other than a cassette tape or Compact Disc into the slot.

z The use of cellular phone inside or near the vehicle may cause a noise from the speakers of the audio sys- tem which you are to. However, this does not indicate a malfunction.

listening

RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station, the weaker its signal will be. conditions change constantly as your vehicle moves.

In addition,

reception

signals are

Here are some common reception prob- lems that probably do not indicate a prob- lem with your radio: FM Fading and drifting stations—Generally, the effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with the distance from the radio transmit- ter. They are often accompanied by distor- tion. Multi−path—FM reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the signals will cancel each oth- er out, causing a momentary flutter or loss of reception. Static and fluttering—These occur when signals are blocked by buildings, trees, or other large objects. Increasing the bass level may reduce static and fluttering. the FM signal you Station swapping—If are interrupted or weak- is ened, and there is another strong station nearby on the FM band, your radio may tune in the second station until the origi- nal signal can be picked up again.

listening to

they can

AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For the best performance for your cas- sette player and tapes: Clean the tape head and other parts regu- larly. D A dirty

tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)

tapes. The easiest way

152

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

D If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.

to be working. Remove

Use high−quality cassettes. D Low−quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto−reversing. They can also get stuck or tangled in the cassette player.

playing

speed,

D Do not use a cassette if it has been damaged or tangled or if its label is peeling off.

D Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.

D Store cassettes in their cases and out

of direct sunlight.

D Avoid using cassettes with a total play- ing time longer than 100 minutes (50
minutes per side). The tape used in these cassettes is thin and could get stuck or tangled in the cassette player.

CARING FOR YOUR COMPACT DISC PLAYER AND DISCS D Use only compact discs

labeled as (CD−Recordable), shown. CD−RW (CD−Re−writable) and personal computer use CD−ROMs may not be playable on your compact disc player.

CD−R

D Your compact disc player is intended for use with 12 cm (4.7 in.) discs only. D Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.

D Bumpy roads or other vibrations may

make your compact disc player skip.

2001 4RUNNER (OM35768U)

153

’01 4Runner_U (L/O 0008)

CAUTION

Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.

radiation exposure

D Your compact disc player cannot play special shaped or low−quality compact discs such as those shown here. Do not use them as the player could be damaged.

inserting

D Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold bend fingerprints them. Avoid getting on them, particularly on the shiny side. D Dirt, scrapes, warping, pin holes, or other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)

D Remove discs from the compact disc player when you are not listening to them. Store them in their plastic cases away from moisture, heat, and direct sunlight.

To clean a compact disc: Wipe it with a soft, lint−free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record cleaner or anti−static device.

154

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Manual air conditioning system

Controls Air flow selector settings Operating tips

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

156
159
159

Automatic air conditioning system

Controls Air flow selector settings Operating tips

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument panel vents Rear heater system

162
166
166
169
171

2001 4RUNNER (OM35768U)

155

’01 4Runner_U (L/O 0008)

Manual air conditioning system— —Controls

1. “A/C” Button (on some models) 2. Air Intake Selector 3. Air Flow Selector 4. Temperature Selector 5. Fan Speed Selector

156

2001 4RUNNER (OM35768U)

’01 4Runner_U (L/O 0008)

Fan speed selector Move the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Move tempera- ture—to the right to warm, to the left to cool.

the knob

to adjust

the

Air flow selector Move the knob to select the vents used for air flow. 1. Panel—Air

flows mainly

from

the

instrument panel vents.

2. Bi−level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor

vents. It is recommended to close the lower vent. For details about it, see “Instru- ment panel vents” in this section.

2001 4RUNNER (OM35768U)

4. Floor/Windshield—Air

the

the air

flow selector

flows mainly floor vents and windshield

to turns on

from vents. the Turning floor/windshield position the defogging function with the purpose of clearing the front view. This position allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. If you want to return the setting to RECIRCULATE mode, press the air in- take selector button once again. Vehicle with “A/C” button— Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly. It is recommended to close the lower vent. For details about it, see “Instru- ment panel vents” in this section.

5. Windshield—Air flows mainly from the

to

flow selector

windshield vents. Turning the the air windshield position turns on the defog- ging function with the purpose of clear- ing the front view. This position allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. 157

’01 4Runner_U (L/O 0008)

If you want to return the setting to RECIRCULATE mode, press the air in- take selector button once again. Vehicle with “A/C” button— Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly. It is recommended to close the lower vent. For details about it, see “Instru- ment panel vents” in this section.

For details about air flow selector settings, see the illustration after “A/C” button.

“A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. If the “A/C” button indicator flashes, there is a problem in the air conditioning system and the air conditioning automatically shuts off. If this happens, take your ve- hicle to a Toyota dealer for service.

Air intake selector Press the button to select the air source. 1. Recirculate—Recirculates the air inside

the vehicle.

2. Fresh—Draws outside air into the sys-

tem.

To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system.

158

2001 4RUNNER (OM35768U)

—Air flow selector settings

: See “Instrument panel vents” in this section.

’01 4Runner_U (L/O 0008)

—Operating tips D To cool off your Toyota after

it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.

D Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).

D On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.

D Keep the area under the front seats clear to allow air to circulate through- out the vehicle.

D On cold days, turn the fan speed se- lector to “HI” for a minute to help clear the intake ducts of snow or moisture. This can reduce the amount of fogging on the windows.

D When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.

2001 4RUNNER (OM35768U)

159

’01 4Runner_U (L/O 0008)

Heating For best results, set controls to:

Air conditioning For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards WARM