2011 Subaru Tribeca Owners Manual

The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the com- pass to read inaccurately. You will notice any outside influence if the compass tends to read in only one particular direction. Should you encounter this situation, return to step 1 of the above procedure and recalibrate the compass.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

3-40 Instruments and controls

& Type C inside mirror (if

equipped)

or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.

Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. ! Photosensors

if

Left button

1) 2) Auto dimming indicator 3) Photosensor 4) Right button

This mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. . By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. . By pressing and releasing the right button, the compass display is toggled on

The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the

Black plate (170,1)

sensors clean using a piece of dry soft cotton cloth or an applicator. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3
seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (approxi- mately two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recali- brate the mirror.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

! Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map attached to the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3
seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode.

Black plate (171,1)

& Outside mirrors

! Remote control mirror switch

Instruments and controls 3-41

! Convex mirror (passenger side)

WARNING

Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and dis- tance of objects that you view in convex mirror.

The remote control mirrors operate only when the ignition switch is in the “ON” or “Acc” position. 1. Turn the knob to the “L” side to adjust the left-hand mirror or to the “R” side to adjust the right-hand mirror. 2. Move the knob in the direction you want to move the mirror. 3. Return the knob to the neutral position to prevent unintentional operation.

The mirrors can also be adjusted manu- ally.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

3-42 Instruments and controls

! Outside mirror defogger

than necessary.

! Power folding mirror switch (if

equipped)

The outside mirror defogger shares the control switch with the rear window de- fogger. Therefore, the outside mirror de- fogger always operates with the rear window defogger.

If the rear window defogger is set to the continuous operation mode, the outside mirror defogger also follows the contin- uous setting. For details, refer to “Rear window defog- ger button” F3-36.

CAUTION

To prevent the battery from being discharged, do not operate the de- fogger continuously for any longer

1) Power folding mirror switch

The power folding mirror switch operates only when the ignition switch is in the “ON” or “Acc” position. To fold the outside mirrors, push the power folding mirror switch. To unfold the mirrors, push the switch again. NOTE . When the temperature is low, the outside mirrors may stop during opera- tion. Push the switch again. When the outside mirrors do not work by switch operation, move them several times

Black plate (172,1)

manually. This makes it possible to operate them by switch operation. . When you operate the power folding mirror switch continuously, it may temporarily stop working. This is not a malfunction. Operate it again after waiting for a short period of time. . When you unfold the outside mirrors manually, the mirrors may become unstable. Be sure to unfold the mirrors the outside by switch operation. mirrors are still unstable, fold the mirrors again manually and then unfold them by switch operation.

If

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Tilt steering wheel

5. Make sure that the steering wheel is securely locked by moving it up and down.

Horn

WARNING

Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.

Black plate (173,1)

Instruments and controls 3-43

to

the seat position. Refer

1. Adjust “Front seats” F1-2. 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place.

To sound the horn, push the horn pad.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22

Ventilator.............................................................. Airflow ................................................................ Ventilator ............................................................ Automatic climate control system ..................... Control panel ...................................................... Rear air conditioner............................................. Temperature sensors...........................................

4-2
4-2
4-4
4-5
4-5
4-9
4-9

Operating tips for heater and air

conditioner....................................................... 4-10
Cleaning ventilator grille..................................... 4-10
Efficient cooling after parking in direct

sunlight ........................................................... 4-10

Black plate (7,1)

Climate control

Lubrication oil circulation in the refrigerant

circuit.............................................................. Checking air conditioning system before summer season ............................................................ Cooling and dehumidifying in high humidity and low temperature weather conditions ................. Air conditioner compressor shut-off when engine is heavily loaded.............................................. Refrigerant for your climate control system ........ Air filtration system ........................................... Replacing the air filter........................................

4-10

4-10

4-10

4-10
4-10
4-11
4-11

北米Model "A3160BE-C" EDITED: 2010/ 11/ 17

4-2 Climate control

Ventilator & Airflow

Ventilator and airflow

: Standard : If equipped

Black plate (176,1)

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

! Airflow mode selection

*: If equipped

Black plate (177,1)

Climate control 4-3

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (178,1)

4-4 Climate control

& Ventilator ! Center ventilators

! Side ventilators

! Rear ventilators

Move the tab to adjust the flow direction.

1) Open 2) Close

Move the tab or rotate it to adjust the flow direction.

Move the tab to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward. To close it, turn the wheel downward.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Automatic climate control system

& Control panel

! AUTO button AUTO mode operation:

Black plate (179,1)

Climate control 4-5

NOTE . Operate the automatic climate con- trol system when the engine is running. . The blower fan rotates at a low speed when the engine coolant tem- perature is low. For efficient defogging or dehumidify- ing in cold weather, press the “A/C” button. . The vehicle has a rear air condi- tioner. The fan speed of the rear air conditioner can be adjusted, but other adjustments (outlet air temperature, air distribution, etc.) are not possible for the rear air conditioner. For details, refer to “Rear air conditioner” F4-9. The automatic climate control system automatically controls outlet air tempera- ture, fan speed, airflow distribution, air inlet control, and air conditioner compres- sor operation. It activates when the “AUTO” button is pressed, and is used to maintain a constant, comfortable climate within the passenger compartment. The temperature can be set within a range of 65 to 858F (18 to 328C).

Fan speed control dial

Temperature control dial (driver’s side)

1) 2) Defroster button 3) 4) Rear window defogger button (Refer to “Rear window defogger button” F3-36.) (passenger’s Temperature control dial side)

5)

6) Air conditioner button 7) Airflow mode selection button 8) Air inlet selection button 9) OFF button 10) AUTO button

When the “AUTO” button is pressed, the indicator light on the button illuminates. In this state, fan speed, airflow distribution, air inlet control, and air conditioner com- pressor operation are automatically con- trolled.

Manual mode operation: If you operate any of the buttons on the control panel other than the “OFF” button and temperature control dial during auto- matic mode operation, the indicator light will turn off. You can then manually control the system as desired using the button you operated. To change the system back to the AUTO mode, press the “AUTO” button.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

4-6 Climate control

! OFF button

! Temperature control dial

The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” button is pressed. When the “OFF” button is pressed, the outside air inlet selection OFF) is automatically selected.

introduction mode (air

Driver’s side

Black plate (180,1)

setting is shown on the display. With the dial set at your desired temperature, the system automatically adjusts the tempera- ture of air supplied from the outlets such that the desired temperature is achieved and maintained.

Turning the dial counterclockwise and releasing it reduces the temperature by 18F (0.58C). Turning the dial clockwise and releasing it increases the temperature by 18F (0.58C). Holding the dial in either turned position causes the temperature to change continuously.

the With the minimum temperature set, system gives maximum cooling perfor- mance. With the maximum temperature set, the system gives maximum heating performance.

Passenger’s side

It is possible to make separate tempera- the driver’s side and ture settings for passenger’s side. Each temperature

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

!

– Defroster button

system to the AUTO mode by pushing the “AUTO” button or turn off by pushing the “OFF” button. Alternatively, push the “ ” button again to return the system to the setting that was selected before you activated the defros- ter. ! Fan speed control dial

”. When the “

To defrost or dehumidify the windshield and front door windows, push the defros- ter button “ ” button is pushed, the indicator light on the button illuminates and the following operation is performed. . The outside air is drawn into the passenger compartment and the airflow is directed towards the windshield and the front door windows. . The air conditioner compressor auto- matically operates to quickly defog the windshield. However, the indicator light on the air conditioner button will not illumi- nate.

After eliminating the fogging from the windshield, return the climate control

The fan speed control dial has 7 positions: AUTO position and 6 different fan speed positions. The fan speed is shown on the center of the dial. in the With the fan speed control dial AUTO position, the fan speed changes automatically corresponding the various conditions: air temperature inside and outside of the passenger’s compartment,

Black plate (181,1)

Climate control 4-7

intensity of the sunlight, etc. ! A/C – Air conditioner button

If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air conditioner button to defog and dehumidify. When this button is pushed, the air conditioner compressor turns on and the indicator light on the button illuminates. After eliminating the fogging from the windshield, set the system back to the AUTO mode by pushing the “AUTO” button. NOTE The air conditioner compressor does not operate when the outside air tem- perature is below 328F (08C).

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (182,1)

4-8 Climate control

! Airflow mode selection button

the instrument panel

turn off.

: Windshield defroster outlets and both

side outlets of the instrument panel For details, refer to “Airflow mode selec- tion” F4-3. ! Air inlet selection button

WARNING

Continued operation in the ON posi- tion may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.

Select the desired airflow mode by push- ing the airflow mode selection button. The selected airflow mode is shown on the center of the dial.

There are five airflow modes that activate the following air outlets.

(Ventilation): Instrument panel outlets

(Bi-level): Instrument panel outlets and

foot outlets

(Heat): Foot outlets, both side outlets of the instrument panel and some through windshield defroster outlets (A small amount of air flows to the windshield and both side windows to prevent fogging.)

(Heat-def): Windshield defroster out- lets, foot outlets and both side outlets of

ON position (recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. The indicator light will illuminate. OFF position (outside air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will

NOTE When driving on a dusty road or behind a vehicle that emits unpleasant exhaust gases, set the air inlet selection button to the ON position. From time to time, return the air inlet selection button to the OFF position to draw outside air into the passenger compartment.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

& Rear air conditioner

. The outlet air temperature of the rear air conditioner cannot be adjusted. . The rear air conditioner cannot be used as a heater.

& Temperature sensors

The rear air conditioner blows cool air out the rear ventilators while the “A/C” of button on the control panel is in the “ON” position. The fan speed of the rear air conditioner can be adjusted using the rear air conditioner dial behind the center console. The fan speed can be adjusted in four steps by turning the dial. Turn the dial to the “OFF” position to stop the fan. NOTE . When the “A/C” button is in the “OFF” position and when the “A/C” indicator is not illuminated during AUTO mode operation, the air condi- tioner compressor does not operate, meaning that the system merely blows uncooled air out of the ventilators.

Interior air temperature sensor

1) 2) Solar sensor

The automatic climate control system employs several sensors. These sensors are delicate. If they are treated incorrectly and become damaged, the system may not be able to control the interior tempera- ture correctly. To avoid damaging the sensors, observe the following precau- tions. – Do not subject the sensors to impact. – Keep water away from the sensors.

Black plate (183,1)

Climate control 4-9

– Do not cover the sensors.

The sensors are located as follows. – Solar sensor: beside windshield defroster grille – Interior air temperature sensor: on the side of the driver-side part of the center panel – Outside temperature sensor: behind front grille

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

4-10 Climate control

Operating tips for heater and air conditioner & Cleaning ventilator grille

Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser.

& Efficient cooling after parking

in direct sunlight

After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the

heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cooling efficiency.

& Lubrication oil circulation in

the refrigerant circuit

Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil.

& Checking air conditioning

system before summer sea- son

Check the air conditioner unit for refriger- ant leaks, hose conditions, and proper operation each spring. Have the air con- ditioning system checked by your SUBARU dealer.

& Cooling and dehumidifying in

high humidity and low tem- perature weather conditions Under certain weather conditions (high relative humidity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning

Black plate (184,1)

system.

& Air conditioner compressor

shut-off when engine is heavily loaded

To improve acceleration and gas mileage, the air conditioner compressor is designed to temporarily shut off during air condi- tioner operation whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.

& Refrigerant for your climate

control system

Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (185,1)

Climate control 4-11

Air filtration system

& Replacing the air filter

Replace the filter element according to the replacement schedule shown in the fol- lowing. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more fre- quently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, we recommend the use of a genuine SUBARU air filter kit.

Replacement schedule:

Every 15 months or 15,000 miles (24,000
km) whichever comes first

2. Unhook the strap.

1. Remove the instrument panel side cover. NOTE The instrument panel side cover is held in place with four pins.

3. Remove the glove box by detaching the one clip on the side.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

4-12 Climate control

Black plate (186,1)

4. Remove the air filter cover by detach- ing the five clips.

6. Replace the air filter with a new one. 7. 8.

Install the air filter cover. Install the glove box.

10. Secure the glove box with the one clip. 11. Install the instrument panel side cover.

5. Unhook the air filter and draw it out.

9. Attach the strap to the hook.

12. Label installation Attach the caution label door.

to the driver’s

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

CAUTION

Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter. – Reduction of the airflow through

the vents.

– Windshield gets easily fogged or

misted.

NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained.

Black plate (187,1)

Climate control 4-13

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22

Black plate (9,1)

Audio

5-2
Antenna system .................................................. 5-2
Printed antenna................................................... 5-2
FM reception ....................................................... 5-2
Installation of accessories.................................. 5-3
Audio set ............................................................. 5-3
Type A audio set ................................................. 5-3
Type B audio set ................................................. 5-4
Type A audio set (if equipped) ........................... Radio operation................................................... 5-4
Compact disc player operation ........................... 5-10

Type B audio set (if equipped).......................... Radio operation ................................................. Built in CD changer operation ............................ Audio control buttons ....................................... MODE button..................................................... Auxiliary input jack............................................ Rear Seat Entertainment (RSE) system

operation (if equipped) ...................................

Precautions to observe when handling a

compact disc...................................................

5-15
5-15
5-21
5-26
5-26
5-28

5-29

5-29

北米Model "A3160BE-C" EDITED: 2010/ 11/ 17

Black plate (190,1)

any other material over the antenna portion of the rear window glass.

Installation of accessories

Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or they are not suited for the vehicle.

if

& FM reception Although FM is normally static free, reception can be affected by the surround- ing area, atmospheric conditions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary static, flutter or station inter- ference. reception continues to be unsatisfactory, switch to a stronger station. NOTE If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio malfunction.

If

5-2 Audio

Antenna system & Printed antenna

CAUTION

Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.

The antenna is printed on the inner surface of the rear window glass. NOTE Antenna performance will deteriorate significantly if you apply tinting film or

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Audio set

& Type B audio set

Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details.

& Type A audio set

. Radio operation: refer to page 5-15
. Built-in CD changer operation: refer to page 5-21

. Radio operation: refer to page 5-4
. CD (compact disc) player operation: refer to page 5-10

Black plate (191,1)

Audio 5-3

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-4 Audio

Type A audio set (if equipped)

The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation

Black plate (192,1)

(1) Satellite radio mode button (2) FM AM mode button (3) Auxiliary audio unit and Rear seat

entertainment selection button

(4) Tuning button (5) AUDIO button (6) Power switch, volume control dial (7) Seek button (8) Scan button (9) Tone and Balance button (10) Preset button ! Power switch and volume control The dial (6) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment. ! Tone and balance control The volume control dial (6) normally functions as a volume control. This dial becomes a control for Bass, Midrange, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

! To change tone and balance control

modes

the “TONE BAL” Each brief press of button (9) changes control modes in the following sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.)

The “TONE BAL” button is used for selecting the following control modes.

Black plate (193,1)

Audio 5-5

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-6 Audio

Control mode (range of le- vels)

Bass control (−6 to +6) Midrange control (−6 to +6) Treble control (−6 to +6) Fader control (R9 to F9)

Balance control (L9 to R9)

Turn counterclockwise

Turn clockwise

For less bass sound

For more bass sound

For less midrange sound

For more midrange sound

For less treble sound

For more treble sound

To increase rear speaker vo-

lume and decrease front speak-

er volume

To increase front speaker vo-

lume and decrease rear speaker

volume

To increase left speaker volume and decrease right speaker vo-

lume

To increase right speaker vo- lume and decrease left speaker

volume

Volume control (0 to 40)

For less volume

AUX volume control* (0 to 40)

For less volume

*: Only when an AUX audio product is connected.

For more volume

For more volume

Black plate (194,1)

! FM/AM radio ! FM/AM selection button Push the “FM AM” button (2) when the radio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. ! Stereo indicator The stereo indicator “ST” will illuminate when an FM stereo broadcast is received. ! Manual tuning Press the “ ” side of the “TUNE TRACK” button (4) to increase the tuning frequency and press the “ ” side of the button to decrease it. Each time the button is pressed, the frequency interval can be changed be- tween 10 kHz in the AM mode and 0.2
MHz in the FM mode. If you hold down the “ the button, the tuning frequency will increase continuously, and if you hold down the “ ” side of the button, the tuning frequency will decrease continuously. Release the button when your desired frequency is reached.

” side of

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

the “TUNE TRACK” button,

NOTE While you are holding down either side of the tuning frequency will not stop chan- ging even if the frequency of a recei- vable station is reached. ! Seek tuning If you press the “ ” side of the ” or “ “SEEK FLDR” button (7), the radio will automatically search for a receivable station and stop at the first one it finds. This function may not be available, how- ever, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. Press the “ ” side of the “SEEK FLDR” button (7) again to cancel the scan mode and to stop on any displayed

” or “

frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop- erly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (10) allows you to select that station in a single operation. Up to six, AM, FM1 and FM2 stations each may be preset. ! How to preset stations 1. Press the “FM AM” button (2) to select FM1, FM2, or AM reception. 2. Press the “SCAN” button (8) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (10) for more than 1.5 seconds to store the frequency. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory.

NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio

Black plate (195,1)

Audio 5-7

it

If is necessary to reset

removal, all stations stored in the this preset buttons are cleared. occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio malfunction. ! Satellite radio mode (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional part) and to enter into a contract with a satellite radio network service such as “XMTM satellite radio” (for U.S.A. only) or “Sirius satellite radio”. For details, please contact your SUBARU dealer. ! Sirius satellite radio Sirius satellite radio is a recent innovation that allows the listener to experience digital sound quality and to have a greater variety of channels. Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer or visit Sirius Satellite Radio at www.sirius.com or call 1-888-539-SIRIUS (7474) for more information. Sirius, the Sirius dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-8 Audio

! XMTM satellite radio (for U.S.A. only) XMTM is a continental U.S. based satellite radio service, including music, news, sports, talk and children’s programming. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XMTM service. For more information, contact XMTM at w w w. x m r a d i o.c o m o r ca l l 1- 80 0 - XMRADIO (1-800-967-2346). ! Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may obstruct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result loss include driving near a wall, steep cliff or hill, or driving on the lower level of a multi- tiered road or inside a parking garage.

in signal

To help reduce this condition, satellite radio providers have installed ground- based repeaters in heavily populated areas. However, you may still experience reception problems in some areas. ! Displaying satellite radio ID of tuner When you activate satellite radio, you should have your satellite radio tuner ID

ready because each tuner is identified by its unique satellite radio tuner ID. The satellite radio ID will be needed when you activate satellite radio and receive satellite radio customer support. The satellite radio ID can be found on the audio display by tuning the channel to “0”. Turn the “TUNE TRACK” button (4) to select the satellite radio channel. ! Band selection button Push the “SAT” button (1) when the radio is off to turn on the radio. Push the “SAT” button when the radio is on to select SAT1, SAT2 or SAT3 recep- tion. ! Channel selection Press “ ” of the “TUNE TRACK” button (4) to select the next channel and press “ ” of the button to select the previous channel. Keep pressing “ the button to change to the next channel continuously and keep pressing “ ” of the button to change to the previous channel continu- ously. ! Category selection Press “ ” of the “SEEK FLDR” button (7) to display the current category. Press “ the next

” again to select

” or “

” of

Black plate (196,1)

” again to select

category, and press “ the previous category. ! Channel scan Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the channels until a station is found. The radio will stop at the station for 5 seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Also during the category selection, chan- nel scan can be performed in that cate- gory. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed channel. ! Selecting preset channels Presetting a channel with a preset button (10) allows you to select that channel in a single operation. Up to six, SAT1, SAT2
and SAT3 channels each may be preset. ! How to preset channels 1. Press the “SAT” button (1) to select SAT1, SAT2 and SAT3 reception. 2. Press the “SCAN” button (8) or the “TUNE TRACK” button (4) to select the channel. 3. Press one of the preset buttons (10)

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

NOTE If your vehicle is equipped with a Rear Seat Entertainment System, refer to the Owner’s Manual supplement for the Rear Seat Entertainment System for further details.

Black plate (197,1)

Audio 5-9

for more than 1.5 seconds to store the channel. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory.

NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio re- moval, all channels stored in the preset buttons are cleared. If this occurs, it is necessary to reset the preset buttons. ! Display selection Press the “AUDIO” button (5) while receiv- ing satellite radio to change the display as follows.

! Rear seat entertainment If your vehicle is equipped with a Rear Seat Entertainment System, you can enjoy audio outputs from the system through the vehicle’s speakers by press- ing the “RSE AUX” button (3). Press the button again to return to the audio set sound.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-10 Audio

& Compact disc player operation

Black plate (198,1)

(1) CD button (2) Track button (3) AUDIO button (4) Seek and Folder button (5) Random button (6) Repeat button (7) Scan button (8) Eject button ! To playback a compact disc ! When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. NOTE . DO NOT INSERT TWO DISCS INTO THE DISC INSERTION SLOT AT THE SAME TIME. . Be sure to insert a disc with the label side up. If you insert the disc the label side down, “CHECK DISC” will appear on the display and the player will not play anything. . After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

. If you insert a disc that cannot be played by the player, “CHECK DISC” will appear on the display and the player will revert to the previously selected mode. . The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones. . CDs (i.e., 8 cm/3 inch CDs) are not supported, and if inserted, they will be immediately ejected. ! When CD is in the player When the “CD” button (1) is pressed, the player will start playback. NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc). ! To stop playback of a CD When the “PUSH POWER” button is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. ! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the “TUNE TRACK” button (2) to skip to the beginning

the button is pressed,

of the next track/file (track). Each time this side of the button is pressed, the indicated track/file (track) number will increase. NOTE In an MP3 folder, skipping past the last track/file (track) will take you back to the first track/file (track) in the folder. ! Backward direction Briefly press the “ ” side of the “TUNE TRACK” button (2) to skip to the beginning of the current track/file (track). Each time this side of the indicated track/file (track) number will decrease. NOTE In an MP3 folder, skipping past the last track/file (track) will take you back to the first track/file (track) in the folder. ! Fast-forwarding and rewinding ! Fast-forwarding Press the “ ” side of the “TUNE TRACK” button (2) continuously to fast-forward the track/file. Release the button to stop fast-forwarding. NOTE If you fast-forward past the last track/ file (track) on the disc, the player will

Black plate (199,1)

Audio 5-11

select the first track/file (track) on the disc and start playing it. ! Rewinding Press the “ ” side of the “TUNE TRACK” button (2) continuously to rewind the track/ file (track). Release the button to stop rewinding. NOTE If you rewind to the beginning of the first track/file (track) on the disc, the rewinding will stop and the player will start playing the first track/file (track) on the disc. ! Folder selection (MP3 disc) Press the “ ” side of the “SEEK FLDR” button (4) briefly to select the next folder. Pressing the “ ” side of the same button the first time makes the player go back to the beginning of the currently selected file; pressing it a second time makes it go back to the previously selected file. NOTE Only MP3 folders are recognized when an attempt to select the next or pre- vious folder is made. If no appropriate folder exists on the disc, pressing the “ ” side of the “SEEK FLDR” button has no effect.

” or “

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-12 Audio

! Repeating ! To repeat the currently playing track/

file (track)

To repeat a track/file (track), briefly press the “RPT” button (6) while the track/file (track) is playing. The display will show “RPT”, and the track/file (track) will be repeated. To cancel the track/file (track) repeat-play mode: Press the “RPT” button once (non-MP3
disc) Press the “RPT” button twice (MP3 disc) The “RPT” indication will turn off, and the normal playback mode will be resumed. NOTE . With an MP3 disc inserted, each time you briefly press the button, the mode will change to the next one in the following sequence.

If you accidentally press the button and cancel the track/file (track) repeat-play mode, press it again to reselect the repeat-play mode. . The repeat-play mode will be can- celed if you perform any of the follow- ing steps.

– Press the “RDM” button – Press the “SCAN” button – Press the “ ” button – Select the radio mode – Press the “RSE AUX” button – Press the “ “SEEK FLDR” button (MP3 disc) – Turn off the power of the audio equipment – Turn the ignition switch to the “LOCK” position

” side of the

” or “

! To repeat the currently playing folder

(MP3 disc)

To repeat the currently playing folder, press the “RPT” button (6) twice while a file (track) is playing. The display will show “F-RPT”, and the folder will be played repeatedly. To cancel the folder repeat-play mode, press the “RPT” button once more. The “F-RPT” indication will turn off, and the normal playback mode will be resumed. NOTE . Each time you briefly press the button, the mode will change to the next one in the following sequence.

If you accidentally press the button and

Black plate (200,1)

cancel the folder repeat-play mode, press it again to reselect the folder repeat-play mode. . The folder repeat-play mode will be cancelled if you perform any of the following steps.

” or “

” side of the

– Press the “RDM” button – Press the “SCAN” button – Press the “ ” button – Select the radio mode – Press the “RSE AUX” button – Press the “ “SEEK FLDR” button (MP3 disc) – Turn off the power of the audio equipment – Turn the ignition switch to the “LOCK” position ! Random playback ! Non-MP3 disc Press the “RDM” button (5) briefly during disc playback to play all of the tracks on the disc in a random order. The display will show “RDM”, and all of the tracks on the disc will be played in a random order. To cancel random mode, press the button again. The “RDM” indication will turn off, and the normal playback mode will be resumed.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

” or “

the audio

the power of

” side of the

NOTE Random playback will be cancelled if you perform any of the following steps. . Press the “RPT” button . Press the “SCAN” button . Press the “ ” button . Select the radio mode . Press the “RSE AUX” button . Press the “ “SEEK FLDR” button . Turn off equipment . Turn the ignition switch to the “LOCK” position ! MP3 disc Press the “RDM” button (5) during disc playback to play all of the tracks in the folder currently being played in random order. Press the “RDM” button again to play all of the tracks on the disc in random order. The display will show “RDM” during the random mode. To cancel the random mode, press the “RDM” button during “in-disc” random playback. The “RDM” indication will turn off, and the normal playback mode will be resumed. NOTE . Each time you briefly press the button, the mode will change to the

next one in the following sequence.

If you accidentally press the button and cancel the random mode, press it again to reselect the random mode. . Random playback will be cancelled if you perform any of the following steps.

– Press the “RPT” button – Press the “SCAN” button – Press the “ ” button – Select the radio mode – Press the “RSE AUX” button – Press the “ ” or “ “SEEK FLDR” button – Turn off the power of the audio equipment – Turn the ignition switch to the “LOCK” position

” side of the

! Scan The scan mode lets you listen to the first 10 seconds of each track/file (track) on the disc/folder in succession. Press the “SCAN” button (7) to start scanning through all tracks upward beginning with the track/file (track) following the currently

Black plate (201,1)

Audio 5-13

” side of the

selected one. After all tracks/files (tracks) on the disc/folder has been scanned, normal playback mode is restored. To cancel a scan, press the button again. NOTE The scan mode will be cancelled if you perform any of the following opera- tions. . Press the “RPT” button . Press the “RDM” button . Press the “ ” button . Press the “ ” or “ “TUNE TRACK” button . Press the “ ” or “ “SEEK FLDR” button (MP3 disc) . Select the radio mode . Press the “RSE AUX” button . Turn off equipment . Turn the ignition switch to the “LOCK” position ! To eject a disc from the player When a disc is being played back or when a disc is in the player, press the “ ” button (8). The disc will be ejected. NOTE . Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.

” side of the

the power of

the audio

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-14 Audio

. If the disc is left ejected for more than approximately 15 seconds after the ignition switch is turned to the “LOCK” position, a disc protection function will operate, automatically reloading the disc. In this case, the disc is not played. ! Display selection (MP3 disc) If you press the “AUDIO” button (3) during playback, the indication will change to the next one in the following sequence.

! Page (track/folder title) scroll (MP3

disc)

If, having pressed the “AUDIO” button (3) to select track title or folder title display, you press the “AUDIO” button again for less than 0.5 second, the title will be scrolled so you can see all of it. You will see eight characters at a time. NOTE The display is designed to show titles for up to three pages (64 characters in total).

Black plate (202,1)

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Type B audio set (if equipped)

The audio set will operate only when the ignition switch is in the “Acc” or “ON” positions. & Radio operation

Black plate (203,1)

Audio 5-15

(1) Satellite radio mode button (2) FM AM mode button (3) Auxiliary audio unit and Rear seat

entertainment selection button

(4) Tuning button (5) AUDIO button (6) Power switch, volume control dial (7) Seek button (8) Scan button (9) Tone and Balance button (10) Preset button ! Power switch and volume control The dial (6) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment. ! Tone and balance control The volume control dial (6) normally functions as a volume control. This dial becomes a control for Bass, Midrange, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-16 Audio

! To change tone and balance control

modes

the “TONE BAL” Each brief press of button (9) changes control modes in the following sequence starting from volume (When the radio is first control mode. turned on, the control mode is in the volume control.)

The “TONE BAL” button is used for selecting the following control modes.

Black plate (204,1)

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Control mode (Range of le- vels)

Bass control (−6 to +6) Midrange control (−6 to +6) Treble control (−6 to +6) Fader control (R9 to F9)

Balance control (L9 to R9)

Turn counterclockwise

Turn clockwise

For less bass sound

For more bass sound

For less midrange sound

For more midrange sound

For less treble sound

For more treble sound

To increase rear speaker vo-

lume and decrease front

speaker volume

To increase front speaker vo-

lume and decrease rear speaker

volume

To increase left speaker volume and decrease right speaker vo-

lume

To increase right speaker vo-

lume and decrease left speaker

volume

Volume control (0 to 40)

For less volume

AUX volume control* (0 to 40)

For less volume

*: Only when an AUX audio product is connected.

For more volume

For more volume

Black plate (205,1)

Audio 5-17

! FM/AM radio ! FM/AM selection button Push the “FM AM” button (2) when the radio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. ! Stereo indicator The stereo indicator “ST” will illuminate when an FM stereo broadcast is received. ! Manual tuning Press the “ ” side of the “TUNE TRACK” button (4) to increase the tuning frequency and press the tuning button marked “ ” to decrease it. Each time the button is pressed, the frequency interval can be changed be- tween 10 kHz in the AM mode and 0.2
MHz in the FM mode. If you hold down the “ the button, the tuning frequency will increase continuously, and if you hold down the “ ” side of the button, the tuning frequency will decrease continuously. Release the button when your desired frequency is reached.

” side of

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

5-18 Audio

NOTE While you are holding down either side of the TUNE/TRACK button, the tuning frequency will not stop changing even if the frequency of a receivable station is reached. ! Seek tuning (SEEK) If you press the “ ” side of the ” or “ “SEEK FLDR” button (7), the radio will automatically search for a receivable station and stop at the first one it finds. This function may not be available, how- ever, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Scan tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. Press the “ ” side of the “SEEK FLDR” button (7) again to cancel the scan mode and to stop on any displayed

” or “

frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop- erly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button allows you to select that station in a single operation. Up to six AM, FM1 and FM2
stations each may be preset. ! How to preset stations 1. Press the “FM AM” button (2) to select FM1, FM2 or AM reception. 2. Press the “SCAN” button (8) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons for more than 1.5 seconds to store the frequency. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory.

NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio

Black plate (206,1)

it

If is necessary to reset

removal, all stations stored in the this preset buttons are cleared. occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio malfunction. ! Satellite radio mode (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional part) and to enter into a contract with a satellite radio network service such as “XMTM satellite radio” (for U.S.A. only) or “Sirius satellite radio”. For details, please contact your SUBARU dealer. ! Sirius satellite radio Sirius satellite radio is a recent innovation that allows the listener to experience digital sound quality and to have a greater variety of channels. Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer or visit Sirius Satellite Radio at www.sirius.com or call 1-888-539-SIRIUS (7474) for more information. Sirius, the Sirius dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

! XMTM satellite radio (for U.S.A. only) XMTM is a continental U.S. based satellite radio service, including music, news, sports, talk and children’s programming. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XMTM service. For more information, contact XMTM at w w w. x m r a d i o.c o m o r ca l l 1- 80 0 - XMRADIO (1-800-967-2346). ! Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may obstruct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result loss include driving near a wall, steep cliff or hill, or driving on the lower level of a multi- tiered road or inside a parking garage.

in signal

To help reduce this condition, satellite radio providers have installed ground- based repeaters in heavily populated areas. However, you may still experience reception problems in some areas. ! Displaying satellite radio ID of tuner When you activate satellite radio, you should have your satellite radio tuner ID

ready because each tuner is identified by its unique satellite radio tuner ID. The satellite radio ID will be needed when you activate satellite radio and receive satellite radio customer support. The satellite radio ID can be found on the audio display by tuning the channel to “0”. Turn the “TUNE/TRACK” button (4) to select the satellite radio channel. ! Band selection button Push the “SAT” button (1) when the radio is off to turn on the radio. Push the “SAT” button when the radio is on to select SAT1, SAT2 or SAT3 recep- tion. ! Channel selection Press “ ” of the “TUNE TRACK” button (4) to select the next channel and press “ ” of the button to select the previous channel. Keep pressing “ the button to change to the next channel continuously and keep pressing “ ” of the button to change to the previous channel continu- ously. ! Category selection Press “ ” of the “SEEK FLDR” button (7) to display the current category. Press “ the next

” again to select

” or “

” of

Black plate (207,1)

Audio 5-19

” again to select

category, and press “ the previous category. ! Channel scan Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the channels until a station is found. The radio will stop at the station for 5 seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Also during the category selection, chan- nel scan can be performed in that cate- gory. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed channel. ! Selecting preset channels Presetting a channel with a preset button (10) allows you to select that channel in a single operation. Up to six, SAT1, SAT2
and SAT3 channels each may be preset. ! How to preset channels 1. Press the “SAT” button (1) to select SAT1, SAT2 and SAT3 reception. 2. Press the “SCAN” button (8) or the “TUNE TRACK” button (4) to select the channel. 3. Press one of the preset buttons (10)

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (208,1)

NOTE If your vehicle is equipped with a Rear Seat Entertainment System, refer to the Owner’s Manual supplement for the Rear Seat Entertainment System for further details.

5-20 Audio

for more than 1.5 seconds to store the channel. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory.

NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio re- moval, all channels stored in the preset buttons are cleared. If this occurs, it is necessary to reset the preset buttons. ! Display selection Press the “AUDIO” button (5) while receiv- ing satellite radio to change the display as follows.

! Rear seat entertainment If your vehicle is equipped with a Rear Seat Entertainment System, you can enjoy audio outputs from the system through the vehicle’s speakers by press- ing the “RSE AUX” button (3). Press the button again to return to the audio set sound.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

& Built in CD changer operation

Black plate (209,1)

Audio 5-21

(1) CD button (2) Track button (3) AUDIO button (4) Seek and Folder button (5) Random button (6) Repeat button (7) Scan button (8) Eject button