2010 Subaru Impreza Owners Manual

the

following operations are performed, map lights turn off immediately. . The ignition switch is turned from the “LOCK” position to the “Acc” or “ON” position. . All doors and the rear gate (5-door) are locked using the remote keyless entry transmitter.

The setting of the period for which the lights remain on (OFF delay timer) can be changed as follows. . Models with genuine SUBARU navi- gation system: The setting can be changed using the navigation monitor. For details, please refer to the Owner’s Manual supplement for the navigation system. Also, the setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. . Models without genuine SUBARU navigation system: The setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details.

6-4 Interior equipment

Sun visors

& Vanity mirror

Storage compartment

CAUTION

Keep the vanity mirror cover closed while the car is being driven to avoid being temporarily blinded by the glare of bright light.

CAUTION

. Always keep the storage com- partment closed while driving to reduce the risk of injury in the event of a sudden stop or an accident.

. Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.

To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.

To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.

& Glove box

& Center console

Cup holders

Interior equipment 6-5

CAUTION

Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, carpets or audio equipment.

& Front passenger’s cup holder

CAUTION

Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident.

Lock

1) 2) Unlock

To open the glove box, pull the handle. To close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clockwise. To unlock the glove box, insert the key and turn it counterclockwise.

To open the lid, pull up the lock release.

& Coin tray (if equipped)

A coin tray is built in the center console.

– CONTINUED –

6-6 Interior equipment

! Except WRX STI

console near the parking brake lever.

cups of different sizes to be held.

A dual cup holder is built in the center console, beside the parking brake lever. ! WRX STI

To access the cup holder, pull toward the rear.

the lid

NOTE With the divider taken out, holder can be used as a storage box.

the cup

The dual cup holder is built into the center

The divider in the cup holder can be pulled out and inserted in a different position (further toward the front or rear) to enable

& Rear passenger’s cup holder

(if equipped)

Bottle holders

trim can be used to hold beverage bottles and other items.

CAUTION

CAUTION

Interior equipment 6-7

When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an accident.

. Do not pick up a bottle from the bottle holder or put a bottle in the holder while you are driving, as this may distract you and lead to an accident.

. When placing a beverage in a door pocket, make sure it is capped. Otherwise, the beverage could spill when opening/closing the door or while driving and, if the beverage is hot, it could scald you.

A dual cup holder is located at the back of the center console. To use the cup holder, open the lid by pulling its upper edge.

The door pocket equipped on each door

6-8 Interior equipment

Accessory power outlets

Power outlet below the climate controls

Power outlet in the center console (except WRX STI)

Power outlet (WRX STI)

in the center console

Accessory power outlets are provided below the climate controls and in the center console. Electrical power (12V DC) from the battery is available at any of the outlets when the ignition switch is in either the “Acc” or “ON” position. You can use an in-vehicle electrical appliance by connecting it to an outlet. The maximum power rating of an appli- ance that can be connected varies among outlets as shown in the following list. Do not use an appliance which exceeds the indicated wattage for each outlet. . Outlet below the climate controls: 80W or less . Outlet in the center console: 120W or less

CAUTION

. Do not attempt to use a cigarette lighter in the accessory power outlets.

. Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Al- ways put the cap on the acces- sory power outlet when it is not in use.

. Use only electrical appliances which are designed for 12V DC. The maximum power rating of an appliance that can be connected varies among outlets as shown in the following list. Do not use an appliance which exceeds the in- dicated wattage for each outlet. – Outlet below the climate con-

trols: 80W or less

– Outlet in the center console:

120W or less

Overloading the accessory power outlet can cause a short circuit. Do not use dual adapters or more than one electrical appli- ance.

Interior equipment 6-9

uine SUBARU cigarette lighter plug. Do not use a non-genuine cigarette lighter plug in the sock- et. Doing so may cause a short- circuit and overheating, resulting in a fire.

. If the socket is ever used for a plug-in accessory such as a cell phone, that may damage the portion of the socket’s internal mechanism that causes a cigar- ette lighter plug to “pop out” after its lighter element is heated. Therefore, do not place a cigar- ette lighter plug in a socket that has been used, even once, to power a plug-in accessory. Doing so may cause the plug to stick and overheat, creating a potential fire hazard.

. If the plug on your electric appli- ance is either too loose or too tight for the accessory power outlet, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly.

. Use of an electric appliance in the accessory power outlet for a long period of time while the engine is not running can cause battery discharge.

. Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accel- erator and brake pedals. If they do, do not use the electrical appliance while driving.

& Use with a cigarette lighter (if

equipped)

To use the accessory power outlet in the center console as a cigarette lighter socket, purchase the cigarette lighter plug, which is an optional accessory. A cigarette lighter plug is available from your SUBARU dealer. The cigarette lighter operates only when the ignition switch is in the “ON” or “Acc” position. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use.

WARNING

To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage the heating element.

CAUTION

. Do not hold the lighter pushed in,

because it will overheat.

. The electrical power socket lo- cated in the center console is originally designed to use a gen-

6-10 Interior equipment

Ashtray (if equipped)

& Center console

& Rear ashtray ! Except WRX STI

CAUTION

Do not use ashtrays as waste re- ceptacles or leave a lighted cigarette in an ashtray. This could cause a fire.

NOTE Particles of ash and tobacco will accu- mulate around the hinges of the ash- tray’s inner lid. Clean them off using a toothbrush or a similar narrow-ended implement.

A portable ashtray is available from your SUBARU dealer. When using the ashtray, open the ashtray lid. Fully close the lid after using it to help reduce residual smoke.

A portable ashtray is available from your SUBARU dealer. When using the ashtray, open the ashtray lid. Fully close the lid after using it to help reduce residual smoke.

! WRX STI (if equipped)

Floor mat (if equipped)

Shopping bag hook (5-door)

Interior equipment 6-11

A retaining pin is located on the driver’s side floor. The floor mat is secured using the built-in grommets, by placing the grommets over the pins and pushing them downward.

CAUTION

Do not hang items on the shopping bag hook that weigh 6 lbs (3 kg) or more.

The rear ashtray is located on the upper side of the back of the center console. To open the ashtray, pull the upper edge of the lid. To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down.

A shopping bag hook is attached to each side of the cargo area.

CAUTION

Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retain- ing pins. Also, do not use more than one floor mat. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.

WARNING

Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury.

CAUTION

Be careful not to scratch the rear gate stays while extending and rewinding the cover. Scratches on the stays could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.

& To remove the cover 1. Rewind the cover.

2. Push the bar to the right side and shorten the bar. 3. Take it off the retainer.

6-12 Interior equipment

Cargo area cover (5-door – if equipped)

The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo.

& Using the cover

To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.

& To install the cover housing 1. Shorten the bar.

Cargo tie-down hooks (5-door – if equipped)

Interior equipment 6-13

CAUTION

The cargo tie-down hooks are de- signed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44
lbs (20 kg) per hook.

2. Insert the projections located on the both ends of the sleeve into the recesses of the retainers.

The cargo area is equipped with four tie- down hooks so that cargo can be secured with a cargo net or ropes. When using the tie-down hooks, turn them down out of the storing recesses. When not in use, put the hooks up into the storing recesses.

the floor of the trunk (4-door) or the cargo area (5-door), and it can be used to store small items. To open the lid, pull the tab up. NOTE When storing a flat tire, put the storage tray in the trunk (4-door) or the cargo area (5-door).

CAUTION

. Always keep the lids closed while driving to reduce the risk of injury in the event of a sudden stop or an accident.

. Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.

6-14 Interior equipment

Under-floor storage compart- ment (if equipped)

4-door models

5-door models

The storage compartment is located under

Fuel ...................................................................... 7-3
Fuel requirements ............................................... 7-3
Fuel filler lid and cap........................................... 7-5
State emission testing (U.S. only)...................... 7-7
Preparing to drive ............................................... 7-9
Starting the engine.............................................. 7-9
MT models .......................................................... 7-9
AT models.......................................................... 7-10
Stopping the engine........................................... 7-11
Remote engine start system

(dealer option) ................................................. 7-11
Starting your vehicle .......................................... 7-12
Remote start safety features ............................... 7-12
Entering the vehicle while it is running via remote

start................................................................. 7-12

Entering the vehicle following remote engine start

shutdown......................................................... 7-12

Pre-heating or pre-cooling the interior of the

vehicle ............................................................. 7-13
Service mode ..................................................... 7-13
Remote engine start transmitter programming

and programmable feature option ..................... 7-13
System maintenance .......................................... 7-14

Manual transmission – 6 speeds

(WRX STI) ........................................................ 7-15
Selecting reverse gear........................................ 7-16
Shifting speeds .................................................. 7-16
Driving tips ........................................................ 7-17

Manual transmission – 5 speeds

(except WRX STI) ............................................ 7-17
Shifting speeds .................................................. 7-18

Starting and operating

Driving tips........................................................

Driver’s Control Center Differential (DCCD)

(WRX STI) ........................................................ To change mode of driver’s control center differential ....................................................... Auto mode ........................................................ Manual mode..................................................... Temporary release ............................................. Automatic transmission .................................... Select lever ....................................................... Shift lock function ............................................. Selection of manual mode.................................. Driving tips........................................................ SPORT mode..................................................... SI-DRIVE (WRX STI)........................................... Intelligent (I) mode ............................................. Sport (S) mode .................................................. Sport Sharp (S#) mode....................................... SI-DRIVE selector .............................................. Limited slip differential (LSD) (WRX STI) ......... Power steering................................................... Braking ............................................................... Braking tips....................................................... Brake system .................................................... Disc brake pad wear warning indicators ............. ABS (Anti-lock Brake System).......................... ABS system self-check ...................................... ABS warning light..............................................

Electronic Brake Force Distribution (EBD)

system .............................................................

7-19

7-19

7-20
7-20
7-21
7-23
7-23
7-24
7-25
7-26
7-27
7-28
7-29
7-29
7-29
7-30
7-30
7-31
7-31
7-31
7-31
7-32
7-32
7-33
7-33
7-33

7-34

Starting and operating

Steps to take if EBD system malfunctions........... 7-35

Vehicle Dynamics Control system

(if equipped) .................................................... 7-36
Vehicle Dynamics Control system monitor .......... 7-37
Vehicle Dynamics Control mode switch

(WRX STI) ........................................................ 7-40

Vehicle Dynamics Control OFF switch

(except WRX STI) ............................................. 7-41

Tire pressure monitoring system (TPMS)

(U.S.-spec. models) ......................................... 7-42
Parking your vehicle .......................................... 7-43
Parking brake..................................................... 7-43
Parking tips ....................................................... 7-44

Hill start assist system

(MT models – if equipped) ............................. To activate/deactivate the Hill start assist system (WRX STI)........................................................ Hill start assist warning light/Hill start assist OFF indicator light .................................................. Cruise control .................................................... To set cruise control .......................................... To temporarily cancel the cruise control ............. To turn off the cruise control.............................. To change the cruising speed ............................ Cruise control indicator light.............................. Cruise control set indicator light ........................

7-45

7-45

7-47
7-47
7-48
7-49
7-49
7-50
7-51
7-51

Fuel

CAUTION

Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage.

& Fuel requirements ! Non-turbo models The engine is designed to operate using unleaded gasoline with an octane rating of 87 AKI or higher. ! Turbo models ! Except WRX STI The engine is designed to operate using premium unleaded gasoline with an octane rating of 91 AKI or higher. If premium unleaded gasoline is not avail- able, regular unleaded gasoline with an octane rating of 87 AKI or higher may be temporarily used. For optimum engine performance and driveability, it is required that you use premium grade unleaded gasoline. NOTE Be sure to use premium unleaded gasoline of 91 AKI or higher. If other

gasoline (lower than 91 AKI) is used, knocking, reduced output and poor accelerator response will result.

fuel

If 93 AKI

! WRX STI The engine is designed to operate at maximum performance using unleaded gasoline with an octane rating of 93 AKI or higher. is not readily available in your area, unleaded gasoline with an octane rating of 91 AKI may be used with no detriment to engine durability or driveability. However, you may notice a slight decrease in maximum engine per- formance while using 91 AKI fuel. Use of 91 AKI fuel will not affect your warranty coverage. ! Fuel octane rating This octane rating is the average of the Research Octane and Motor Octane numbers and is commonly referred to as the Anti Knock Index (AKI). Using a gasoline with a lower octane rating can cause persistent and heavy knocking, which can damage the engine. Do not be concerned if your vehicle sometimes knocks lightly when you drive up a hill or when you accelerate. Contact your SUBARU dealer if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently.

Starting and operating 7-3

! Unleaded gasoline The neck of the fuel filler pipe is designed to accept only an unleaded gasoline filler nozzle. Under no circumstances should leaded gasoline be used because it will damage the emission control system and may impair driveability and fuel economy. ! Gasoline for California-certified

LEV

If your vehicle was certified to California’s low emission vehicle (LEV) standards as indicated on the underhood tune-up label, it is designed to optimize engine and emission performance with gasoline that meets the clean burning low-sulfur Cali- fornia gasoline specifications. If you live in any other state than California, your vehicle will operate on gasoline meeting Federal specifications. Gasoline sold out- side California is permitted to have higher sulfur levels, which may affect the perfor- mance of your vehicle’s catalytic converter and may produce a sulfur exhaust odor or smell. SUBARU recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related before returning your vehicle to an authorized dealer for service.

– CONTINUED –

7-4 Starting and operating

it

If

for service.

! MMT Some gasoline contains an octane-en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). If you use such fuels, your emission control system performance may deteriorate and the CHECK ENGINE warning light/Mal- function indicator lamp may turn on. If this return to your authorized happens, SUBARU Dealer is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty. ! Gasoline for cleaner air Your use of gasoline with detergent additives will help prevent deposits from forming in your engine and fuel system. This helps keep your engine in tune and your emission control system working properly, and is a way of doing your part for cleaner air. If you continuously use a high quality fuel with the proper detergent and other additives, you should never need to add any fuel system cleaning agents to your fuel tank. Many gasolines are now blended with materials called oxygenates. Use of these fuels can also help keep the air cleaner. Oxygenated blend fuels, such as MTBE (Methyl Tertiary Butyl ether) or ethanol (ethyl or grain alcohol) may be used in

. If undesirable driveability problems are experienced and you suspect they may be fuel related, try a different brand of gaso- line before seeking service at your SUBARU dealer. . Fuel system damage or driveability problems which result from the use of improper fuel are not covered under the SUBARU Limited Warranty.

CAUTION

Do not let fuel spill on the exterior surfaces of the vehicle. Because fuel may damage the paint, be sure to wipe off any spilled fuel quickly. Paint damage caused by spilled fuel is not covered under the SUBARU Limited Warranty.

your vehicle, but should contain no more than 15% MTBE or 10% ethanol for the proper operation of your SUBARU. In addition, some gasoline suppliers are now producing reformulated gasolines, which are designed to reduce vehicle emissions. SUBARU approves the use of reformulated gasoline. If you are not sure what the fuel contains, you should ask your service station operators if their gasolines contain deter- gents and oxygenates and if they have been reformulated to reduce vehicle emis- sions. As additional guidance, only use fuels suited for your vehicle as explained in the following description. . Fuel should be unleaded and have an octane rating no lower than that specified in this manual. . Methanol (methyl or wood alcohol) is sometimes mixed with unleaded gasoline. Methanol can be used in your vehicle ONLY if it does not exceed 5% of the fuel mixture AND if is accompanied by sufficient quantities of the proper cosol- vents and corrosion inhibitors required to prevent damage to the fuel system. Do not use fuel containing methanol EXCEPT under these conditions.

it

& Fuel filler lid and cap ! Refueling Only one person should be involved in refueling. Do not allow others to approach the area of the vehicle near the fuel filler pipe while refueling is in progress. Be sure to observe any other precautions that are posted at the service station.

Starting and operating 7-5

1. To open the fuel filler lid, pull the lid release lever up. The lever is on the floor at the left of the driver’s seat.

WARNING

Before opening the fuel filler cap, first touch the vehicle body or a metal portion of the fuel pump or similar object to discharge any static electricity that may be present on your body. If your body is carry- ing an electrostatic charge, there is a possibility that an electric spark could ignite the fuel, which could burn you. To avoid acquiring a new static electric charge, do not get back into the vehicle while refueling is in progress.

1) Open 2) Close

2. Remove the fuel filler cap by turning it slowly counterclockwise.

WARNING

. Gasoline vapor is highly flam- mable. Before refueling, always first stop the engine and close all vehicle doors and windows. Make sure that there are no lighted cigarettes, open flames or electrical sparks in the adja- cent area. Only handle fuel out- doors. Quickly wipe up any spilled fuel.

– CONTINUED –

7-6 Starting and operating

. When opening the cap, grasp it firmly and turn it slowly to the left. Do not remove the cap quickly. Fuel may be under pres- sure and spray out of the fuel filler neck, especially in hot weather. If you hear a hissing sound while you are removing the cap, wait for the sound to stop and then slowly open the cap to prevent fuel from spraying out and creating a fire hazard.

4. Hook the cord that is attached to the fuel filler cap onto the hook inside the fuel filler lid (except WRX STI).

WARNING

. When refueling,

insert

the fuel nozzle securely into the fuel filler pipe. If the nozzle is lifted or not fully inserted, its automatic stop- ping mechanism may not func- tion, causing fuel to overflow the tank and creating a fire hazard.

3. Set the fuel filler cap on the cap holder inside the fuel filler lid (WRX STI).

. Stop refueling when the auto- matic stop mechanism on the fuel nozzle activates. If you con- tinue to add fuel, temperature changes or other conditions may cause fuel to overflow from

the tank and create a fire hazard.

5. Stop filling the tank after the fuel filler pump automatically stops. Do not add any more fuel. 6. Put the cap back on, turn it clockwise until you hear a clicking noise. Be certain not to catch the tether under the cap while tightening. 7. Close the fuel filler lid completely. If you spill any fuel on the painted surface, rinse it off the painted surface could be damaged.

immediately. Otherwise,

NOTE . You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. . If the fuel filler cap is not tightened until it clicks or if the tether is caught under the cap, the CHECK ENGINE warning light/malfunction indicator lamp may illuminate. Refer to “CHECK ENGINE warning light/Malfunction in- dicator lamp” F3-19.

as a result of an empty tank could cause damage to the en- gine.

CAUTION

. Never add any cleaning agents to the fuel tank. The addition of a cleaning agent may cause da- mage to the fuel system.

. After refueling, turn the cap to the right until it clicks to ensure that it is fully tightened. If the cap is not securely tightened, fuel may leak out while the vehicle is being driven or fuel spillage could occur in the event of an accident, creating a fire hazard.

. Do not let fuel spill on the exterior surfaces of the vehicle. Because fuel may damage the paint, be sure to wipe off any spilled fuel quickly. Paint damage caused by spilled fuel is not covered under the SUBARU Limited Warranty.

filler cap.

. Always use a genuine SUBARU fuel If you use the wrong cap, it may not fit or have proper venting and your fuel tank and emission control system may be damaged. It could also lead to fuel spillage and a fire.

. Immediately put fuel in the tank whenever the low fuel warning light illuminates. Engine misfires

Starting and operating 7-7

State emission testing (U.S. only)

At state inspection time, remember to tell your inspection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dynam- ometer. Otherwise, serious transmis- sion damage will result. Some states have started using dynam- ometers in their state inspection programs in order to meet their obligation under federal law to implement stricter vehicle emission standards to reduce air pollution from vehicles. A dynamometer is a tread- mill or roller-like testing device that allows your vehicle’s wheels to turn while the vehicle remains in one place. Depending on the severity of a state’s air pollution problems, the states must adopt either a “basic” or “enhanced” vehicle emission inspection test. Normally, a portion of the basic emission test consists of an emis- sion inspector inserting an analyzer probe into the exhaust pipe of an idling vehicle for a short period of time. States with more severe air pollution problems are required to adopt an enhanced vehicle emission test. This test simulates actual driving conditions on a dynamometer and permits more accurate measurement of tailpipe emitted pollution than the basic emission – CONTINUED –

7-8 Starting and operating

test. The U.S. Environmental Protection Agency (EPA) and states using two-wheel dynamometers in their emission testing programs have EXEMPTED SUBARU AWD vehicles from the portion of the testing program that involves a two-wheel dynamometer. There are some states that use four-wheel dynamometers in their testing programs. When properly used, that equipment will not damage a SUBARU AWD vehicle. Under no circumstances should the rear wheels be jacked off the ground, nor should the driveshaft be disconnected for state emission testing.

WARNING

Testing of an All-Wheel Drive model must NEVER be performed on a single two-wheel dynamometer. At- tempting to do so will result in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby.

CAUTION

Resultant vehicle damage due to improper testing is not covered under the SUBARU Limited War- ranty and is the responsibility of the state inspection program or its contractors or licensees.

The EPA has issued regulations for inspecting the On-Board Diagnostic (OBD) system as part of the state emis- sions inspection. The OBD system is designed to detect engine and transmis- sion problems that might cause vehicle emissions to exceed allowable limits. These inspections apply to all 1996 model year and newer passenger cars and light trucks. Over 30 states plus the District of Columbia have implemented the OBD system inspection. . The inspection of the OBD system consists of a visual operational check of the “CHECK ENGINE” warning light/mal- function indicator lamp (MIL) and an examination of the OBD system with an electronic scan tool while the engine is running. . A vehicle passes the OBD system inspection if proper the “CHECK ENGINE” warning light/MIL is observed, there are no stored diagnostic

illumination of

trouble codes, and the OBD system readiness monitors are complete. . A vehicle fails the OBD inspection if the “CHECK ENGINE” warning light/MIL is not properly operating or there are one or more diagnostic trouble codes stored in the vehicle’s computer with the “CHECK ENGINE” warning light/MIL illuminated. . A state emission inspection may reject (not pass or fail) a vehicle if the number of OBD system readiness monitors “Not Ready” is greater than one. Under this condition, the vehicle operator should be instructed to drive his/her vehicle for a few days to set the monitors and return for an emission re-inspection. . Owners of rejected or failing vehicles should contact their SUBARU Dealer for service.

Preparing to drive

Starting the engine

Starting and operating 7-9

the engine does not start,

If following.

try the

You should perform the following checks and adjustments every day before you start driving. 1. Check that all windows, mirrors, and lights are clean and unobstructed. 2. Check the appearance and condition of the tires. Also check tires for proper inflation. 3. Look under the vehicle for any sign of leaks. 4. Check that and rear gate (5-door) are fully closed. 5. Check the adjustment of the seat. 6. Check the adjustment of and outside mirrors. 7. Fasten your seatbelt. Check that your passengers have fastened their seatbelts. 8. Check the operation of the warning and indicator lights when the ignition switch is turned to the “ON” position. 9. Check the gauges, indicator and warn- ing lights after starting the engine.

trunk (4-door)

the inside

the hood,

NOTE Engine oil, engine coolant, brake fluid, washer fluid and other fluid levels should be checked daily, weekly or at fuel stops.

CAUTION

Do not operate the starter motor continuously for more than 10 sec- onds. If the engine fails to start after operating the starter for 5 to 10
seconds, wait for 10 seconds or more before trying again.

& MT models 1. Apply the parking brake. 2. Turn off unnecessary lights and ac- cessories. 3. Depress the clutch pedal to the floor and shift the shift lever into neutral. Hold the clutch pedal to the floor while starting the engine. The starter motor will only operate when the clutch pedal is depressed fully to the floor. 4. Turn the ignition switch to the “ON” position and check the operation of the warning and indicator lights. Refer to “Warning and indicator lights” F3-16. 5. Turn the ignition switch to the “START” position without depressing the accelera- tor pedal. Release the key immediately after the engine has started.

for at

for at

(1) Turn the ignition switch to the least “OFF” position and wait the 10 seconds. After checking that parking brake is firmly set, turn the ignition switch to the “START” position while depressing the accelerator pedal slightly (approximately a quarter of the full stroke). Release the accelerator pedal as soon as the engine starts. (2) If this fails to start the engine, turn the ignition switch back to the “OFF” position and wait least 10
seconds. Then fully depress the accel- erator pedal and turn the ignition switch to the “START” position. If the engine starts, quickly release the accelerator pedal. (3) If this fails to start the engine, turn the ignition switch again to the “OFF” position. After waiting for 10 seconds or longer, turn the ignition switch to the “START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance.

6. Confirm that all warning and indicator lights have turned off after the engine has started. The fuel injection system auto- matically lowers the idle speed as the

– CONTINUED –

7-10 Starting and operating

engine warms up.

NOTE . The engine may be difficult to start when the battery has been discon- nected and reconnected (for mainte- nance or other purposes). This diffi- culty is caused by the electronically controlled throttle’s self-diagnosis function. To overcome it, keep the ignition switch in the “ON” position for approximately 10 seconds before starting the engine. . For non-turbo models, to protect the engine while the shift lever is in the neutral position, the engine is con- trolled so that the engine speed may not become too high even if the accel- erator pedal is depressed hard. & AT models 1. Apply the parking brake. 2. Turn off unnecessary lights and ac- cessories. 3. Shift the select lever to the “P” or “N” position (preferably the “P” position). The starter motor will only operate when the select lever is at the “P” or “N” position. 4. Turn the ignition switch to the “ON” position and check the operation of the warning and indicator to

lights. Refer

“Warning and indicator lights” F3-16. 5. Turn the ignition switch to the “START” position without depressing the accelera- tor pedal. Release the key immediately after the engine has started. If following.

the engine does not start,

try the

for at

(1) Turn the ignition switch to the least “OFF” position and wait the 10 seconds. After checking that parking brake is firmly set, turn the ignition switch to the “START” position while depressing the accelerator pedal slightly (approximately a quarter of the full stroke). Release the accelerator pedal as soon as the engine starts. (2) If this fails to start the engine, turn the ignition switch back to the “OFF” position and wait least 10
seconds. Then fully depress the accel- erator pedal and turn the ignition switch to the “START” position. If the engine starts, quickly release the accelerator pedal. (3) If this fails to start the engine, turn the ignition switch again to the “OFF” position. After waiting for 10 seconds or longer, turn the ignition switch to the “START” position without depressing the accelerator pedal. (4) If the engine still refuses to start,

for at

contact your nearest SUBARU dealer for assistance.

6. Confirm that all warning and indicator lights have turned off after the engine has started. The fuel injection system auto- matically lowers the idle speed as the engine warms up.

While the engine is warming up, make sure that the select lever is at the “P” or “N” position and that the parking brake is applied.

CAUTION

If you restart the engine while the vehicle is moving, shift the select lever into the “N” position. Do not attempt to place the select lever of a moving vehicle into the “P” posi- tion.

NOTE . The engine may be difficult to start when the battery has been discon- nected and reconnected (for mainte- nance or other purposes). This diffi- culty is caused by the electronically controlled throttle’s self-diagnosis function. To overcome it, keep the ignition switch in the “ON” position for approximately 10 seconds before

starting the engine. . For non-turbo models, to protect the engine while the select lever is in the “P” or “N” position, the engine is controlled so that the engine speed may not become too high even if the accelerator pedal is depressed hard.

Stopping the engine

The ignition switch should be turned off only when the vehicle is stopped and the engine is idling.

WARNING

Do not stop the engine when the vehicle is moving. This will cause loss of power to the power steering and the brake booster, making steer- ing and braking more difficult. It could also result in accidental acti- vation of the “LOCK” position on the ignition switch, causing the steering wheel to lock.

Starting and operating 7-11

Remote engine start system (dealer option)

WARNING

(e.g.,

. Do not start the engine using the remote start system in an en- closed environment in a closed garage). Prolonged opera- tion of a motor vehicle in an enclosed environment can cause a harmful build-up of Carbon Monoxide. Carbon Monoxide is harmful to your health. Exposure to high levels of Carbon Monox- ide can cause headaches, dizzi- ness or in extreme cases uncon- sciousness and/or death.

. Before performing any servicing of the vehicle, temporarily place the remote engine start system in service mode to prevent the system from unexpectedly start- ing the engine.

– CONTINUED –

7-12 Starting and operating

& Starting your vehicle The remote engine start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote engine start transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds. While the vehicle is operating via remote engine start, the vehicle’s power window features will be disabled. Also, the system has a timer and will shut down after 15 minutes if you do not operate the vehicle. Press and hold the “ ” button for 2 seconds again to turn the vehicle off. If the vehicle’s starter cranks but does not start or starts and stalls, the remote engine start system will power off then attempt to start the vehicle

an additional four times. If the vehicle fails to start after the additional attempts, the remote engine start system will abort and return to a non-activated state.

& Remote start safety features For safety and security reasons, the system will fail to start and beep the horn twice or shut down the engine during remote start operation if any of the following conditions occur. . The brake pedal is depressed before the vehicle ignition switch is turned “on”. . The key was already in the ignition switch. . The engine hood is opened. . The vehicle’s engine idle speed has reached a level over 3,000 rpm. . The alarm is triggered by opening a door or the rear gate. NOTE . The security indicator light on the combination meter will stop flashing while under remote engine start opera- tion, but the vehicle is still protected. the vehicle is entered during . If remote engine start operation, the system will not record entry in the alarm history.

& Entering the vehicle while it is running via remote start

turn off.

1. Unlock the vehicle doors using the remote keyless entry system. If the vehi- cle’s doors are unlocked manually using the key, the vehicle’s alarm system will trigger and the remote engine start system will Inserting the key into the ignition switch and turning it to the “ON” position or pressing the unlock button “ ” on the remote keyless entry transmitter will disarm the alarm system. Refer to “Alarm system” F2-14. 2. Enter the vehicle. Do not depress the brake pedal. 3. Insert the key into the ignition switch and turn to the “ON” position. If the ignition switch is accidentally turned to the “START” position, the system’s “starter anti-grind” feature will prevent the starter from re-cranking. 4. Depress the brake pedal. The remote starter disengages, the vehicle’s power window features are re-enabled and the vehicle will operate normally.

& Entering the vehicle follow-

ing remote engine start shut- down

An alarm trigger may occur if the vehicle is opened by the remote keyless entry

transmitter within a few seconds immedi- ately following remote engine start shut- down.

& Pre-heating or pre-cooling the interior of the vehicle

Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.

& Service mode In service mode, the remote start function is temporarily disabled to prevent the system from unexpectedly starting the engine while being serviced. ! To engage the service mode Turn the ignition switch to the “ON” position, depress and hold the brake pedal, ” button on the remote engine start trans- mitter three times. The system will pause for 1 second and then flash the turn signal lights and honk the horn three times indicating that the system is in service mode. When attempting to activate the remote start system while in service mode, the turn signal lights will flash and the horn will honk two times and will not

then press and release the “

then press and release the “

start. ! To disengage the service mode Turn the ignition switch to the “ON” position, depress and hold the brake pedal, ” button on the remote engine start trans- mitter three times. The system will pause for 1 second and flash the turn signal lights once indicating that the system has exited service mode. NOTE When taking your vehicle in for service, it is recommended that you inform the service personnel that your vehicle is equipped with a remote engine start system.

& Remote engine start trans-

mitter programming and pro- grammable feature option

New transmitters can be programmed to the remote engine start system in the event that remote engine start transmitters are lost, stolen or damaged. The remote engine start system also has one pro- grammable feature that can be adjusted for user preference. The remote engine start system can be programmed to either make an audible horn chirp upon remote start activation or

Starting and operating 7-13

Insert the key into the vehicle’s ignition

not. Remote engine start transmitter pro- gramming and feature programming can be adjusted using the following procedure. 1. Open the driver’s door (the driver’s door must remain opened throughout the entire process). 2. switch and turn to the “ON” position. 3. Locate the small black programming button behind the fuse box cover, on the driver’s side left under the dashboard panel. 4. Press and hold the black programming button for 10 to 15 seconds. The horn will honk and the turn signal lights will flash three times to indicate that the system has entered programming mode. At this point you can proceed to either step 5 or step 6. 5. To program a remote engine start transmitter: press and release the “ ” button on each transmitter. The horn will honk and the turn signal lights will flash one time to indicate a successful trans- mitter learn each time the “ ” button is pressed. You can program up to eight transmitters. 6. To toggle the Horn Confirmation chirps ON/OFF: depress and release the brake pedal to toggle the feature. The horn will chirp and the turn signal lights will flash one time to indicate Confirmation Horn Chirps are “OFF”. The horn will honk and – CONTINUED –

an incorrect replacement battery is used. Replace only with the same or equivalent type of bat- tery.

. Batteries should not be exposed to excessive heat such as sun- shine, fire or the like.

The two 3-volt lithium batteries (model CR-1220) supplied in your remote engine start transmitter should last approximately 3 years, depending on usage. When the batteries begin to weaken, you will notice a decrease in range (distance from the vehicle that your remote engine start system operates). Follow the instructions below to change the remote engine start transmitter batteries.

1. Carefully pry the remote engine start transmitter halves apart using a small flat- head screwdriver.

7-14 Starting and operating

the turn signal lights will flash 2 times to indicate Confirmation Horn Chirps are “ON”. Depressing the brake pedal repeat- edly will toggle the feature ON or OFF each time. 7. To exit the remote engine start trans- mitter and feature programming mode, turn the ignition switch to the “LOCK” position, remove the key from the ignition switch and test operation of the remote engine start transmitter(s) and horn con- firmation feature.

& System maintenance ! Changing the batteries

CAUTION

. Do not let dust, oil or water get on or in the remote engine start transmitter when replacing the battery.

. Be careful not

to damage the printed circuit board in the re- mote engine start transmitter when replacing the battery.

. Be careful not to allow children to touch the battery and any re- moved parts; children could swallow them.

. There is a danger of explosion if

Starting and operating 7-15

Manual transmission – 6
speeds (WRX STI)

to the following two conditions: (1) This device may not cause harmful inter- this device must ference, and (2) accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

2. Remove the circuit board from the bottom half of the case and slide the white plastic battery holder out from under the battery tab releasing the batteries. Re- move the old batteries and replace with new ones. Be sure to observe the (+) sign on the old batteries before removing them to ensure that the new batteries are inserted properly (battery “+” should be pointed away from the transmitter circuit board on both batteries). 3. Carefully snap the case halves back together, then test the remote engine start system.

NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject

The manual transmission is a fully syn- chromeshed, 6-forward-speed and 1-re- verse-speed transmission. The shift pattern is shown on the shift lever knob.

– CONTINUED –

7-16 Starting and operating

WARNING

Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased.

& Selecting reverse gear

1) Slider

You must raise the slider and hold it in that position before you can move the shift lever to the “R” position. To change gears, fully depress the clutch

pedal, move the shift lever, and gradually let up on the clutch. If it is difficult to shift into gear, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

CAUTION

Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmis- sion to try shifting into reverse when the vehicle is moving.

& Shifting speeds ! Recommended shifting speeds The best compromise between fuel econ- omy and vehicle performance during normal driving is ensured by shifting up at the speeds listed in the following table.

Shift up 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th

mph (km/h)

15 (24) 25 (40) 40 (64) 45 (72) 50 (80)

! Maximum allowable speeds The following table shows the maximum speeds that are possible with each differ- ent gear. The tachometer’s needle will enter the red area if these speeds are exceeded. With the exception of cases where sudden acceleration is required, the vehicle should not be driven with the tachometer’s needle inside the red area. Failure to observe this precaution can lead to excessive engine wear and poor fuel economy.

Gear 1st 2nd 3rd 4th

mph (km/h)

31 (50) 50 (81) 74 (119) 99 (159)

WARNING

When shifting down a gear, ensure that the vehicle is not travelling at a speed exceeding the Maximum Al- lowable Speed for the gear which is about to be selected. Failure to observe this precaution can lead to engine over-revving and this in turn can result in engine damage.

In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased.

NOTE Never exceed posted speed limits.

& Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components. When it is necessary to reduce vehicle speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor. On steep downgrades, downshift the transmission to 5th, 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life.

Starting and operating 7-17

Manual transmission – 5
speeds (except WRX STI)

In this way, the engine provides a braking effect. Remember, if you “ride” (over use) the brakes while descending a hill, they may overheat and not work properly. The engine may, on rare occasions, knock when the vehicle rapidly accelerates or rapidly pulls away from a standstill. This phenomenon does not indicate a malfunc- tion.

The manual transmission is a fully syn- chromeshed, 5-forward-speed and 1-re- verse-speed transmission. The shift pattern is shown on the shift lever knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear. To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch pedal. If it is difficult to shift into gear, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

– CONTINUED –

7-18 Starting and operating

WARNING

Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased.

CAUTION

Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmis- sion to try shifting into reverse when the vehicle is moving.

& Shifting speeds ! Recommended shifting speeds The best compromise between fuel econ- omy and vehicle performance during normal driving is ensured by shifting up at the speeds listed in the following table.

Non-turbo models

1st 2nd 3rd

Turbo models

Shift up 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th

mph (km/h)

15 (24) 25 (40) 40 (64) 45 (72)

! Maximum allowable speeds The following tables show the maximum speeds that are possible with each differ- ent gear. Never exceed the speed limit listed in the following table for each gear position except for brief acceleration in an emer- gency. The tachometer’s needle will enter the red area if these speeds are ex- ceeded. Failure to observe this precaution can lead to excessive engine wear and poor fuel economy.

mph (km/h)

32 (51) 53 (86) 76 (122)

mph (km/h)

35 (56) 58 (94) 85 (137)

1st 2nd 3rd

Never exceed the posted speed limit.

WARNING

When shifting down a gear, ensure that the vehicle is not travelling at a speed exceeding the Maximum Al- lowable Speed for the gear which is about to be selected. Failure to observe this precaution can lead to engine over-revving and this in turn can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased.

& Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components. When it is necessary to reduce vehicle speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor. On steep downgrades, downshift the transmission to 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life. In this way, the engine provides a braking effect. Remember, if you “ride” (over use) the brakes while descending a hill, they may overheat and not work properly. The engine may, on rare occasions, knock when the vehicle rapidly accelerates or rapidly pulls away from a standstill. This phenomenon is not an indication of a problem in your vehicle.

Driver’s Control Center Dif- ferential (DCCD) (WRX STI)

WARNING

Always use the utmost care when driving. Being overconfident be- cause you are driving a vehicle with a driver’s control center differential could easily lead to a serious acci- dent.

CAUTION

All the indicator lights will flash in the event that the driver’s control center differential has a malfunc- tion. Have the vehicle inspected by your SUBARU dealer.

limitation of

The driver’s control center differential allows you to freely change the degree of the differential action (limited slip differential (LSD) torque) of your vehicle’s center differential. By using the center differential control switch, you can set an initial LSD torque to match the road surface conditions, driving conditions and your driving style.

Starting and operating 7-19

LSD torque Traction torque Initial LSD torque (maximum) Initial LSD torque (minimum) Initial LSD torque (adjustable)

1) 2) 3) 4) A) B) Mechanical LSD torque The driver’s control center differential has an auto mode and a manual mode. In the the system automatically auto mode, adjusts the initial LSD torque. In the manual mode, you can change to the desired mode manually by using the center differential control switch. NOTE If you rapidly depress and release the accelerator pedal while driving at low speed, you may hear a knocking sound from the vicinity of the center differen-

– CONTINUED –

7-20 Starting and operating

tial and rear differential. This sound occurs because of the structure of the center differential. It does not indicate a problem.

& To change mode of driver’s

control center differential

& Auto mode

In the auto mode, the system estimates the driving and road conditions using signals from the wheel speed sensor, throttle position sensor, steering angle sensor and brake switch, etc. According to the result, it electronically and auto- matically controls the degree of limitation of the differential action (LSD torque) to optimize the differential action of the center differential. When the ignition switch is turned ON, the “AUTO” indicator light on the combination meter illuminates.

Press the “AUTO-MANU” switch on the center console to switch from auto mode to manual mode or vice versa. When you select the auto mode, the “AUTO” indica- tor light illuminates. When you select the manual mode, the “AUTO” indicator light turns off.

The auto mode has 3 modes as follows.

Mode

AUTO [+]

AUTO

AUTO [−]

Operation

This mode emphasizes traction control and strengthens the limitation of differential action that is suitable for driving on slippery roads for vehicle stabi- lity. This mode is suitable for most driving situations. This mode is suitable when you seek quick response from the steering wheel and smooth driving.

! Mode setting method In most situations, it is recommended that the “AUTO” mode is selected.

Push the control switch forward to select

the “AUTO [+]” mode. After setting the mode, “ ” on the combination meter illuminates.

& Manual mode

Starting and operating 7-21

! Center differential control switch

and indicator light

In the manual mode, you can use the center differential control switch to adjust the initial LSD torque as desired. When this mode is selected, the “AUTO” indica- tor light on the combination meter turns off.

Pull the control switch rearward to select the “AUTO [−]” mode. After setting the mode, “ ” on the combination meter illuminates. When the “AUTO [+]” mode is selected, pull the control switch rearward to change to the “AUTO” mode. When the “AUTO [−]” mode is set, push the control switch forward to change to the “AUTO” mode.

The control switch is located beside the parking brake lever. By pushing the control switch forward or pulling it rear- ward, it is possible to change the initial LSD torque. The center differential indicator lights on the combination meter give six levels of indication. The indicator lights and control switch are linked; when the switch is pushed or pulled to change the initial LSD torque, the illumination position of the indicator lights changes accordingly.

– CONTINUED –

7-22 Starting and operating

Push the switch forward to increase the initial LSD torque; when the “LOCK” indicator light illuminates, the initial LSD torque setting is maximum. The center differential will then be almost completely locked.

. When a temporary spare tire is

installed

. When your vehicle is towed . When the vehicle is stopped with the manual mode se- lected

NOTE . A higher initial LSD torque setting gives the vehicle greater traction when driving straight ahead but makes cor- nering more difficult. Remember this when adjusting the initial LSD torque. In general, higher initial LSD torque settings assist driving on slippery roads and lower settings for non-slip- pery roads. When the vehicle is stuck in snow or mud, setting the initial LSD torque to the maximum will help to free the vehicle. . The setting of the initial LSD torque will remain even when the auto mode is selected or the ignition switch is turned to the “OFF” position. However, the initial LSD torque will be minimized when the battery is disconnected and reconnected. . During cornering or when making turns (especially when going into the garage), the rotational difference be- tween the front and rear wheels may

Pull the switch rearward to reduce the initial LSD torque. When the lowest posi- tion of the driver’s control center differen- tial the initial LSD torque will be minimum. Under this condition, only the Mechanical LSD torque will limit the differential action.

indicator light

illuminates,

CAUTION

. Do not operate the control switch when a wheel slippage occurs. Wait until the wheelspin has been brought under control.

. Under any of the following con- ditions after setting to the man- ual mode, pull the center differ- ential control switch to minimize the initial LSD torque:

cause a braking effect accompanied by vibration and noise. This does not indicate a problem. The phenomenon will disappear when setting the initial LSD torque to the minimum. In the auto mode, it controls the initial LSD torque automatically. While in the auto mode, this phenomenon some- times occurs depending on the driving condition, however, it does not indicate a problem. . Use the center differential indicator light only as a rough indication of the initial LSD torque. . If you operate the center differential control switch while quickly accelerat- ing or turning a tight corner, you may feel slight shocks. This is due to differential action by the center differ- ential and does not indicate a problem.

& Temporary release When the driver stops the vehicle and pulls the parking brake lever after manu- ally setting the initial LSD torque, the LSD torque is temporarily minimized. However the indicator on the combination meter continues to show the driver’s selected initial LSD torque. When the driver re- leases the parking brake lever, the initial LSD torque set by the driver is restored.

Starting and operating 7-23

Automatic transmission

The automatic transmission is electroni- cally controlled and provides 4 forward speeds and 1 reverse speed. Also, it has a manual mode and a SPORT mode.

WARNING

Do not shift from the “P” or “N” position into the “D” or “R” position while depressing the accelerator pedal. This may cause the vehicle to jump forward or backward.

“R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmis- sion.

. When parking the vehicle, first securely apply the parking brake and then place the select lever in the “P” position. Avoid parking for a long time with the select lever in any other position as doing so could result in a dead battery.

CAUTION

. Shift into the “P” or “R” position only after the vehicle is comple- tely stopped. Shifting while the vehicle is moving may cause damage to the transmission.

. Do not race the engine for more than 5 seconds in any position except the “N” or “P” position when the brake is set or when chocks are used in the wheels. This may cause the automatic transmission fluid to overheat.

. Avoid shifting from one of the forward driving positions into the

NOTE . When the engine coolant tempera- ture is still low, the automatic transmis- sion will upshift to higher engine speeds than when the coolant tempera- ture is sufficiently high in order to shorten the warm-up time and improve driveability. The gearshift timing will automatically shift to the normal timing after the engine has warmed up. . Immediately after ATF (automatic transmission fluid) is replaced, you may feel that the automatic transmis- sion operation is somewhat unusual. This results from invalidation of data which the on-board computer has collected and stored in memory to

– CONTINUED –

7-24 Starting and operating