Login- Download PDF Manual
-
When a tire’s tread wear indicator becomes vis- ible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at high speeds in wet weather can cause the vehicle to hydroplane. The resulting loss of vehicle control can lead to an accident.
NOTE For safety, inspect tire tread regularly and replace the tires before their tread wear indicators become visible.
11-52
(cid:132) Tire rotation
HSB056BA
Tire wear varies from wheel to wheel. To maximize the life of each tire and ensure that the tires wear uniform- ly, it is best to rotate the tires every 7,500 miles (12,500 km). Rotating the tires involves switching the front and rear tires on the right hand side of the vehicle and similarly switching the front and rear tires on the left hand side of the vehicle. (Each tire must be kept on its original side of the vehicle.) Replace any damaged or unevenly worn tire at the time of rotation. After tire rotation, adjust the tire pres- sures and make sure the wheel nuts are correctly tightened.
After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose.
(cid:132) Tire replacement The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbi- trarily. The tires fitted as standard equipment are opti- mally matched to the characteristics of the vehicle and were selected to give the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a size and construc- tion matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard. Using tires of a non-specified size detracts from con- trollability, ride comfort, braking performance, speed- ometer accuracy and odometer accuracy. It also cre- ates incorrect body-to-tire clearances and inappropri- ately changes the vehicle’s ground clearance. All four tires must be the same in terms of manufactur- er, brand (tread pattern), construction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equipment. For safe vehicle operation, SUBARU recommends re-
Maintenance and service
placing all four tires at the same time.
(cid:121) All four tires must be the same in terms of manufacturer, brand (tread pattern), construc- tion, degree of wear, speed symbol, load index and size. Mixing tires of different types, sizes or degrees of wear can result in damage to vehi- cle’s power train. Use of different types or sizes of tires can also dangerously reduce controlla- bility and braking performance and can lead to an accident. (cid:121) Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously reduce control- lability, resulting in an accident.
(cid:132) Wheel replacement When replacing wheels due, for example, to damage, make sure the replacement wheels match the specifi- cations of the wheels that are fitted as standard equip- ment. Replacement wheels are available from SUBARU dealers.
– CONTINUED – 11-53
Maintenance and service
Use only those wheels that are specified for your vehicle. Wheels not meeting specifica- tions could interfere with brake caliper opera- tion and may cause the tires to rub against the wheel well housing during turns. The resulting loss of vehicle control could lead to an acci- dent.
NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nuts after driving approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque.
Aluminum wheels Aluminum wheels can be scratched and damaged easily. Handle them carefully to maintain their appear- ance, performance, and safety. (cid:121) When any of the wheels is removed and replaced for tire rotation or to change a flat, always check the tightness of the wheel nuts after driving approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque. (cid:121) Never apply oil to the threaded parts, wheel nuts, or tapered surface of the wheel. (cid:121) Never let the wheel rub against sharp protrusions or curbs. (cid:121) Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. (cid:121) When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels.
11-54
Intercooler water spray (WRX-STi)
Maintenance and service
UGB079BA
Add water to the intercooler water spray tank when the intercooler water spray warning light in the combina- tion meter comes on. The warning light comes on when the water in the tank has decreased to approxi- mately 0.4 liters (0.4 US qt, 0.4 Imp qt).
UGB514BA
The tank is located on the right hand side of the trunk. NOTE (cid:121) Use only pure water for refilling. (cid:121) In cold weather (when you do not use the inter- cooler water spray), keep the tank half-empty in case the water freezes. A larger amount of water could break the tank if it froze.
– CONTINUED – 11-55
Washer Fluid Concentration
Freezing Temperature
30% 50% 100%
10.4°F (–12°C) –4°F (–20°C) –49°F (–45°C)
Never use engine coolant as washer fluid be- cause it could cause paint damage.
Maintenance and service
Windshield washer fluid
UGB134HA
Check the level of the washer fluid at each fuel stop. If the level is low, fill the fluid up to the neck of the reser- voir. Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti- freeze type windshield washer fluid. SUBARU Wind- shield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing temper- ature varies according to how much it is diluted, as in- dicated in the following table.
11-56
Replacement of wiper blades Grease, wax, insects, or other material on the wind- shield or the wiper blade results in jerky wiper opera- tion and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the wind- shield and wiper blades with clean water. The wind- shield is clean if beads do not form when you rinse the windshield with water.
Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.
If you cannot eliminate the streaking even after follow- ing this method, replace the wiper blades using the fol- lowing procedures:
Maintenance and service
(cid:132) Windshield wiper blades assembly 1. Raise the wiper arm off the windshield.
UGB133BB
1) Stopper 2. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while depressing the wiper blade stopper. 3. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 4. Hold the wiper arm by hand and slowly lower it in position.
– CONTINUED – 11-57
Maintenance and service
(cid:132) Windshield wiper blade rubber
HSB059BB
1) Metal support 1. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the metal support.
HSB060BB
1) Metal spines 2. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
11-58
3. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber as- sembly into the metal support until it locks.
HSB061BA
Maintenance and service
HSB062BB
1) Stopper 2) 4. Be sure to position the claws at the end of the metal support between the stoppers on the rubber as shown. If the rubber is not retained properly, the wiper blade may scratch the windshield.
(cid:132) Rear window wiper blade assembly 1. Raise the wiper arm off the rear window.
– CONTINUED – 11-59
Maintenance and service
3. Pull the wiper blade assembly toward you to re- move it from the wiper arm.
(cid:132) Rear window wiper blade rubber
2. Turn the wiper blade assembly counterclockwise.
UBB554BA
1. Pull out the end of the blade rubber assembly to un- lock it from the plastic support.
UBB523BA
UBB555BA
11-60
Maintenance and service
USB586BA
USB583BC
2. Pull the blade rubber assembly out of the plastic support.
A) Metal spines 3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
– CONTINUED – 11-61
Maintenance and service
USB586CA
USB584BA
4. Align the claws of the plastic support with the grooves in the blade rubber assembly, then slide the blade rubber assembly into place.
Securely retain both ends of the rubber with the stop- pers on the plastic support ends. If the rubber is not re- tained properly, the wiper may scratch the rear win- dow glass. 5. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 6. Hold the wiper arm by hand and slowly lower it in position.
11-62
Battery
(cid:121) Before beginning work on or near any bat- tery, be sure to extinguish all cigarettes, match- es, and lighters. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. (cid:121) For safety, in case an explosion does occur, wear eye protection or shield your eyes when working near any battery. Never lean over a bat- tery. (cid:121) Do not let battery fluid contact eyes, skin, fabrics, or paint because battery fluid is a cor- rosive acid. If battery fluid gets on your skin or in your eyes, immediately flush the area with water thoroughly. Seek medical help immedi- ately if acid has entered the eyes. If battery fluid is accidentally swallowed, imme- diately drink a large amount of milk or water, and seek medical attention immediately. (cid:121) To lessen the risk of sparks, remove rings, metal watchbands, and other metal jewelry. Never allow metal tools to contact the positive battery terminal and anything connected to it WHILE you are at the same time in contact with
Maintenance and service
any other metallic portion of the vehicle be- cause a short circuit will result. (cid:121) Keep everyone including children away from the battery. (cid:121) Charge the battery in a well-ventilated area. (cid:121) Battery posts, terminals and related accesso- ries contain lead and lead compounds, chemi- cals known to the State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.
– CONTINUED – 11-63
Maintenance and service
L O L O
U P P E R L E V E L W E R L E V E L W E R L E V E L
life.
UGB117BB
1) Cap 2) Upper level 3) Lower level It is unnecessary to periodically check the battery fluid level or periodically refill with distilled water. However, if the battery fluid level is below the lower level, remove the cap. Fill to the upper level with dis- tilled water.
Never use more than 10 amperes when charg- ing the battery because it will shorten battery
11-64
Fuses
Never replace a fuse with one having a higher rating or with material other than a fuse be- cause serious damage or a fire could result.
The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse boxes.
Maintenance and service
To remove the coin tray, open the cover and pull the coin tray out.
UGB550BA
One is located under the instrument panel behind the coin tray on the driver’s seat side.
UGB088BA
– CONTINUED – 11-65
Maintenance and service
HSB065BA
HSB066BB
The other one is housed in the engine compartment.
1) Fuse puller 2) Spare fuse The fuse puller and spare fuses are stored in the main fuse box cover in the engine compartment.
11-66
A
Maintenance and service
HSB067BB
HSB068BB
A) Good B) Blown If any lights, accessories or other electrical controls do not operate, inspect the corresponding fuse. If a fuse has blown, replace it. 1. Turn the ignition switch to the “LOCK†position and turn off all electrical accessories. 2. Remove the cover. 3. Determine which fuse may be blown. The back side of each fuse box cover and the “Fuses and circuits†section in chapter 12 in this manual show the circuit for each fuse.
1) Fuse puller 4. Pull out the fuse with the fuse puller. 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs.
– CONTINUED – 11-67
Maintenance and service
Main fuse
Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your ve- hicle. Such accessories may cause the electronic sys- tem to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
HSB065BA
Main fuse box The main fuses are designed to melt during an over- load to prevent damage to the wiring harness and electrical equipment. Check the main fuses if any elec- trical component fails to operate (except the starter motor) and other fuses are good. A melted main fuse must be replaced. Use only replacements with the same specified rating as the melted main fuse. If a main fuse blows after it is replaced, have the electrical system checked by your nearest SUBARU dealer.
11-68
Replacing bulbs
10 11
15
14 13 12
Maintenance and service
14 16
15
10
11
UGB135BB
– CONTINUED – 11-69
Maintenance and service
1) Front turn signal 2) Spot light 3) Room light 4) Parking light 5) Low beam head light
Wattage 12V-21W 12V-8W 12V-8W 12V-5W
U.S.-spec. WRX-STi 12V-35W Except U.S.-spec. 12V-55W WRX-STi
6) Front fog light 12V-55W 7) High beam head light 12V-60W
8) Trunk room light 9) High mount stop light
12V-16W
Bulb No. – – – 168
D2R H1
H3
9005
(HB3) W16WSedan (in compartment) (in rear spoiler) Wagon
10) Backup light 11) Rear turn signal
12) Brake/tail light 13) Tail light 14) Brake light 15) License plate light
11-70
921
912
7440
–12V-18W 12V-1.2W – 12V-13W 12V-21W 12V-21W (Amber) 12V-21/5W 7443
12V-21/5W 7443
7440
12V-21W 12V-5W 16816) Cargo area light
Wattage 12V-13W
Bulb No. –
(cid:132) Headlights (U.S.-spec. WRX-STi)
High-intensity-discharge (HID) bulbs are used for the low beams of the headlights on the U.S.- spec. WRX-STi. These HID bulbs use an ex- tremely high voltage. To avoid the risk of an electric shock and resulting serious injury, you should not attempt to replace them. Neither should you attempt to replace the high-beam bulbs, remove/refit the headlight assemblies, or remove any headlight-assembly compo- nents. For replacement of the headlight bulbs (low-beam and high-beam), removal and instal- lation of the headlight assemblies, and removal of headlight-assembly components, contact your SUBARU dealer.
(cid:132) Headlights (Except U.S.-spec. WRX-
STi)
(cid:84) Low beam light bulbs
Maintenance and service
Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface will develop into hot spots and cause the bulb to break. If there are finger prints or grease on the bulb surface, wipe them away with a soft cloth moistened with alcohol.
NOTE (cid:121) If headlight aiming is required, consult your SUBARU dealer for proper adjustment of the head- light aim. (cid:121) It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if neces- sary.
1. Remove the bulb cover, by turning it counterclock- wise.
UGB516BA
– CONTINUED – 11-71
Maintenance and service
2. Disconnect the electrical connector.
UGB517BA
UGB518BA
11-72
3. Remove the retainer spring. 4. Replace the bulb, then set the retainer spring se- curely. 5. Reconnect the electrical connector. 6. Install the bulb cover. (cid:84) High beam light bulbs
1. Disconnect the electrical connector from the bulb.
UGB519CA
Maintenance and service
(cid:132) Front turn signal light bulbs
UGB520BA
2. Remove the bulb from the headlight assembly by turning it counterclockwise. 3. Replace the bulb with new one. 4. Reconnect the electrical connector. At this time, use care not to touch the bulb surface. 5. To install the bulb to the headlight assembly, turn it clockwise until it clicks.
1. Remove the bulb socket from the headlight assem- bly by turning it counterclockwise.
UGB536CA
– CONTINUED – 11-73
Maintenance and service
(cid:132) Parking light
UGB531BA
2. Pull the bulb out of the socket. Install a new bulb. 3. Set the bulb socket into the headlight assembly and turn it clockwise until it locks. 4. Install the headlight assembly and the front grille in the reverse order of removal.
UGB523BB
1) Parking light The headlight assembly must be removed before the parking light bulbs can be replaced. When the head- light assembly has been removed and then rein- stalled, it may become necessary to make a headlight aiming adjustment. It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.
11-74
(cid:84) Before removing the headlight assembly
Maintenance and service
1. Loosen four clips at the top of the front bumper.
UGB525BA
(cid:99): Clip (cid:133): Hook
UGB528BA
– CONTINUED – 11-75
Maintenance and service
(cid:84) Removal of headlight assembly
2. Remove the front grille. Use a screwdriver to de- tach the four clips at the top and the two hooks on each side.
UGB529BA
11-76
UGB534BA
UGB533CA
1. Remove two bolts and disconnect connectors.
(cid:84) Parking light bulbs
Maintenance and service
2. Pull the headlight assembly toward you and re- move it from the vehicle.
1. Remove the bulb socket from the headlight assem- bly by turning it counterclockwise.
UGB551BA
UGB535BA
– CONTINUED – 11-77
Maintenance and service
(cid:132) Rear combination lights (cid:84) Sedan
1. Remove the clip from the rear trunk trim with a screwdriver.
UGB538BA
UGB532BA
2. Pull the bulb out of the socket. Install a new bulb. 3. Set the bulb socket into the headlight assembly and turn it clockwise until it locks. 4. Install the headlight assembly and the front grille in the reverse order of removal.
(cid:132) Front fog light It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.
11-78
2
(cid:84) Wagon
Maintenance and service
54
UGB539BB
1) Backup light 2) Rear turn signal light 3) Brake/tail light 4) Tail light 5) Brake light 2. Open the rear portion of the side trunk trim panel. 3. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 4. Remove the bulb from the socket by pushing it and turning counterclockwise. Install a new bulb. 5. Set the bulb holder into the rear combination light assembly and turn it clockwise until it locks. 6. Secure the rear trunk trim panel with the clips.
1. Using a Phillips screwdriver, remove the upper and lower screws that secure the side cover of the rear combination light assembly.
UGB540BA
– CONTINUED – 11-79
Maintenance and service
UGB541BA
UGB542BB
2. Remove the upper and lower screws. Then, slide the rear combination lamp assembly to the rear and remove it from the vehicle.
1) Brake/tail light 2) Rear turn signal light 3) Backup light 3. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 4. Remove the bulb from the socket by pushing it and turning counterclockwise. Install a new bulb. 5. Set the bulb holder into the rear combination light assembly and turn it clockwise until it locks. 6. Close the cover and latch the lock. 7. Reinstall the rear combination light assembly and its side cover.
11-80
(cid:132) License plate light
(cid:132) Dome light, map light and cargo area
light
Maintenance and service
UGB136BA
1. Remove the mounting screws using a Phillips screwdriver. 2. Remove the cover and lens. 3. Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the lens and cover. 5. Tighten the mounting screws.
HSB088BA
– CONTINUED – 11-81
Maintenance and service
a flat-head screwdriver. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the lens.
(cid:132) Trunk light
UGB544BA
UGB137BA
1. Remove the cover by squeezing its sides and pull- ing it. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover.
1. Remove the lens by prying the edge of the lens with
UGB078BA
11-82
(cid:132) High mount stop light (cid:84) Sedan
(cid:84) Wagon
Maintenance and service
UGB546BA
1. Remove the high mount stop light cover by prying the edge with a screwdriver. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover.
HSB091BA
1. Remove the mounting screw covers by prying the edge with a screwdriver. 2. Remove the mounting screws using a Phillips screwdriver and then remove the high mount stop light cover. 3. Remove the bulbs from the socket by pushing it and turning counterclockwise. Install a new bulb. 4. Reinstall the cover. 5. Tighten the mounting screws then reinstall the cov- ers. NOTE Other bulbs may be difficult to replace. Have your – CONTINUED – 11-83
Maintenance and service
SUBARU dealer replace these bulbs if necessary.
11-84
Specifications
Dimensions ....................................................... Engine ................................................................ Electrical system .............................................. Capacities .......................................................... Tires ................................................................... Wheel alignment ...............................................
Specifications ................................................ 12-2
12-2
12-3
12-3
12-4
12-5
12-6
Fuses and circuits ........................................ 12-7
12-7
12-9
Bulb chart ...................................................... 12-10
Vehicle identification .................................... 12-11Fuse panel located behind the coin tray ....... Fuse panel located in the engine compartment ..................................................
12
12-1
Specifications
SpecificationsSpecifications These specifications are subject to change without notice. (cid:132) Dimensions
Item
2.5-liter non-turbo RS, RS sport
package
Sedan 2.0-liter turbo
WRX
2.5-liter turbo
WRX-STi
Wagon
2.5-liter non-turbo
2.0-liter turbo
in (mm)
RS
OUTBACK
SPORT
WRX
Drive system Transmission type Overall length Overall width
Sedan Wagon Overall height Without roofrail With roofrail
Wheel base
Tread
Front
Rear
AT
MT
AT
MT
MT
AWD AT
173.8 (4,415)
MT
AT
MT
AT
MT
68.5 (1,740)
– 56.7 (1,440)
– 99.4 (2,525)
58.5 (1,485)
58.1 (1,475)
58.3 (1,480)
66.7 (1,695) 57.7 (1,465)
58.5 (1,485)
–
67.3 (1,710) 58.1 (1,475)
58.9 (1,495) 99.4 (2,525)
66.7 (1,695) 57.7 (1,465)
58.5 (1,485)
57.7 (1,465)
57.5 (1,460)
57.7 (1,465)
57.3 (1,455)
5.9 (150)
6.3 (160)
6.1 (155)
56.3 (1,430)
100 (2,540) 58.7 (1,490) 58.9 (1,495) 5.7 (145)
Ground clearance*1
5.9 (150)
6.1 (155)
*1: Measured with vehicle empty AT: Automatic transmission MT: Manual transmission
12-2
(cid:132) Engine Engine model
Engine type Displacement cc (cu-in) Bore × Stroke in (mm) Compression ratio Firing order (cid:132) Electrical system MT Battery type and capacity (5HR) AT
Alternator
Spark plugs
AT: Automatic transmission MT: Manual transmission
Specifications
EJ253
(2.5-liter, SOHC, non-turbo)
EJ205 (2.0-liter, DOHC, turbo) EJ257 (2.5-liter, DOHC, turbo)
Horizontally opposed, liquid cooled 4 cylinder, 4-stroke gasoline engine
2,457 (150)
1,994 (122)
2,457 (150)
3.9 × 3.1 (99.5 × 79.0)
3.6 × 2.9 (92.0 × 75.0)
3.9 × 3.1 (99.5 × 79.0)
10.0 : 1
8.0 : 1
1 – 3 – 2 – 4
8.2 : 1
With 2.5-liter non-turbo engine With 2.0-liter turbo engine 2.5-liter non-turbo and 2.0-liter turbo engine 2.5-liter turbo engine 2.5-liter non-turbo engine 2.0-liter turbo engine 2.5-liter turbo engine
12V-48AH (55D23L) 12V-52AH (75D23L) 12V-52AH (65D23L)
12V-75A
12V-90A FR5AP-11
PFR6G (NGK) IFLR6B (NGK)
– CONTINUED – 12-3
5 speed 6 speed
2.5-liter non-turbo engine
2.0-liter turbo engine
2.5-liter turbo engine
MT AT MT AT MT
15.9 US gal (60 liters, 13.2 Imp gal)
4.2 US qt (4.0 liters, 3.5 Imp qt) 3.7 US qt (3.5 liters, 3.1 Imp qt) 4.3 US qt (4.1 liters, 3.6 Imp qt) 10.0 US qt (9.5 liters, 8.4 Imp qt) 0.7 US qt (0.7 liter, 0.6 Imp qt) 7.4 US qt (7.0 liters, 6.2 Imp qt) 7.3 US qt (6.9 liters, 6.1 Imp qt) 8.1 US qt (7.7 liters, 6.8 Imp qt) 8.0 US qt (7.6 liters, 6.7 Imp qt) 8.1 US qt (7.7 liters, 6.8 Imp qt)
Specifications
(cid:132) Capacities Fuel tank Engine oil Transmission oil (MT)
Transmission oil (AT) Power steering gear fluid Engine coolant
AT: Automatic transmission MT: Manual transmission
12-4
(cid:132) Tires
Tire size Wheel size Pressure
Temporary spare tire
Item
Front
Rear
Size Pressure
Specifications
RS, RS sport package,
WRX
P205/55R16 89V
16 × 61/2 JJ
32 psi
(220 kPa, 2.2 kgf/cm2)
WRX (option tire)*1
WRX-STi
215/45R17 87W
225/45R17 90W
17 × 7 JJ 33 psi
(230 kPa, 2.3 kgf/cm2)
17 × 8 JJ 36 psi
(250 kPa, 2.5 kgf/cm2)
29 psi
(200 kPa, 2.0 kgf/cm2)
32 psi
(220 kPa, 2.2 kgf/cm2)
30 psi
(210 kPa, 2.1 kgf/cm2)
T135/70 D16
T135/70 D17
60 psi (420 kPa, 4.2 kgf/cm2)
*1: The recommended cold tire pressure for the 215/45R17 87W tire is not indicated on the vehicle placard attached to the driver’s side B-pillar since this tire is a dealer option for the WRX. If your vehicle is equipped with 215/45R17 87W tires, be sure to adjust them to the air pressure shown on this page.
– CONTINUED – 12-5
Specifications
(cid:132) Wheel alignment
Item
Sedan
Wagon
2.5-liter non-turbo
RS, RS sport
package
2.0-liter turbo
2.5-liter turbo
2.5-liter non-turbo
2.0-liter turbo
WRX
WRX-STi
RS
OUTBACK
SPORT
WRX
Drive system Toe
Camber
Front Rear Front Rear
AWD
0 in (0 mm) 0 in (0 mm)
–0°15’ –1°25’
–0°25’ –1°30’
–0°30’ –1°40’
–0°10’ –1°15’
–0°05’ –1°10’
–0°20’ –1°20’
12-6
Fuses and circuits (cid:132) Fuse panel located behind the coin
tray
10
11
12
13 14
15 16
17
18 19
20 21 22 23
HSC001BB
Specifications
Fuse panel
Fuse rating
Circuit
10
11
15A
15A
15A
20A
10A
15A
15A
20A
15A
Empty
15A
(cid:121) Heater fan
(cid:121) Heater fan
(cid:121) Power door lock (cid:121) Remote keyless entry
(cid:121) Cigarette lighter (cid:121) Remote controlled rear
view mirrors
(cid:121) Tail light (cid:121) Parking light
(cid:121) SRS airbag
(cid:121) Fog light
(cid:121) ABS solenoid
(cid:121) Radio
(cid:121) Engine ignition system (cid:121) SRS airbag (cid:121) AT control system
– CONTINUED – 12-7
Specifications
Fuse panel
Fuse rating
Circuit
Fuse panel
Fuse rating
Circuit
(cid:121) Accessory power outlet
(cargo)
(cid:121) Seat heater
23
20A
10A
10A
10A
30A
20A
15A
15A
20A
Empty
Empty
10A
(cid:121) Illumination brightness
control
(cid:121) Combination meter (cid:121) SRS lamp
(cid:121) Rear window wiper and
washer
(cid:121) Windshield wiper and
washer
(cid:121) Brake light
(cid:121) Air conditioner
(cid:121) Backup light (cid:121) Cruise control
(cid:121) Mirror heater
(cid:121) ABS ignition
12
13
14
15
16
17
18
19
20
21
22
12-8
(cid:132) Fuse panel located in the engine com-
partment
9 10 11 12
6 7 8
UGC012BB
1 2
A) FWD socket (AT models except Turbo) B) Main fuse C) Engine sensor (Non-turbo models)
Specifications
Fuse panel
Fuse rating
Circuit
10
11
12
20A
20A
30A
20A
15A
15A
10A
10A
15A
15A
20A
20A
(cid:121) Radiator cooling fan
(Main)
(cid:121) Radiator cooling fan
(Sub)
(cid:121) ABS motor
(cid:121) Rear window defogger
(cid:121) Hazard warning flasher (cid:121) Horn
(cid:121) Turn signal lights
(cid:121) Automatic transmis-
sion control unit
(cid:121) Alternator
(cid:121) Headlight (right side)
(cid:121) Headlight (left side)
(cid:121) Lighting switch
(cid:121) Clock (cid:121) Interior light
– CONTINUED – 12-9
Specifications
Bulb chart
Description Headlight
U.S.-spec. WRX- STi version Low beam High beam
Except U.S.-spec. WRX-STi version
Low beam High beam Front fog light Front turn signal Parking light Rear combination light
Wattage
Bulb type
12V-35W 12V-60W
D2R 9005 (HB3)
12V-55W 12V-60W 12V-55W 12V-21W 12V-5W
H1
9005 (HB3) H3
– 168Description High mount stop light
Sedan (in compartment) Sedan (in rear spoiler) Wagon
License plate light Trunk room light Cargo area light Front ashtray light Dome light Map light
Wattage
Bulb type
12V-18W
921
12V-1.2W 12V-13W 12V-5W 12V-16W 12V-13W 12V-1.4W 12V-8W 12V-8W
– 912
168
W16W – – – –Brake light (Sedan) 12V-21W Brake/tail light Turn signal light
12V-21/5W 12V-21W (Amber) 12V-21/5W 12V-21W
7440
7443– 7443
7440Tail light (Sedan) Back-up light
12-10
Specifications
1) Vehicle identification number 2) Vacuum hose connections la-
bel/Emission control label 3) Tire inflation pressure label 4) Certification plate 5) Bar cord label (U.S. only) 6) Vehicle identification number
plate
7) Model number plate 8) Radio noise label (Canada only) 9) Fuel label
Vehicle identification
UGC013BB
– CONTINUED – 12-11
Consumer information and Reporting safety defects
Tire information ............................................. 13-2
13-2
Tire labeling ....................................................... 13-5
Recommended tire inflation pressure ............ 13-7
Glossary of tire terminology ............................ Tire care – maintenance and safety 13-8
practices ......................................................... 13-9
Vehicle load limit – how to determine ............. Determining compatibility of tire and vehicle load capacities ............................................... 13-13
Adverse safety consequences of overloading on handling and stopping and on tires ........ 13-14
Steps for Determining Correct Load Limit ..... 13-14
Uniform tire quality grading standards ....... 13-15
Treadwear .......................................................... 13-15
Traction AA, A, B, C .......................................... 13-15
Temperature A, B, C ......................................... 13-16
Reporting safety defects (USA) ................... 13-1713
13-1
Consumer information and Reporting safety defects
Consumer information and Reporting safety defects
For U.S.A. The following information has been compiled accord- ing to Code of Federal Regulations “Title 49, Part 575â€.
vide more dimensional information about the tire size. Example:
Tire information (cid:132) Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers. These marking can provide you with useful information on the tire. (cid:84) Tire size Your vehicle comes equipped with P-Metric tire size. It is important to understand the sizing sys- tem in selecting the proper tire for your vehicles. Here is a brief review of the tire sizing system with a breakdown of its individual elements. (cid:86) P Metric With the P-Metric system, Section Width is mea- sured in millimeters. To convert millimeters into inches, divide by 25.4. The Aspect Ratio (Sec- tion Height divided by Section Width) helps pro-
13-2
(4)
(3)
(2)
P 205 / 55 R 16
(1) (5) (1) P = Certain tire type used on light duty vehi- cles such as passenger cars (2) Section Width in millimeters (3) Aspect Ratio (= section height ÷ section width). (4) R = Radial Construction (5) Rim diameter in inches (cid:86) Load and Speed Rating Descriptions The load and speed rating descriptions will ap- pear following the size designation. They provide two important facts about the tire. First, the number designation is its load index. Second, the letter designation indicates the tire’s speed rating.Example:
P 205 / 55 R 16 89 V (7)
Size designation
(6)
(6) Load Index: A numerical code which speci- fies the maximum load a tire can carry at the speed indicated by its speed symbol, at maxi- mum inflation pressure. For example, “90†means 1,323 lbs (600 kg), “89†means 1,278 lbs (580 kg).
Load indices apply only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load.
(7) Speed Rating: An alphabetical system de- scribing a tire’s capability to travel at established and predetermined speeds. For example, “V†means 149 mph (240 km/h)
Consumer information and Reporting safety defects
(cid:121) Speed ratings apply only to the tire, not to the vehicle. Putting a speed rated tire on any vehicle does not mean the vehicle can be operated at the tire’s rated speed. (cid:121) The speed rating is void if the tires are worn out, damaged, repaired, retreaded, or otherwise altered from their original condi- tion. If tires are repaired, retreaded, or oth- erwise altered, they may not be suitable for original equipment tire designed loads and speeds.
(cid:84) Tire Identification Number (TIN) Tire Identification Number (TIN) is marked on the intended outboard sidewall. The TIN is com- posed of four groups. Here is a brief review of the TIN with a breakdown of its individual elements.
DOT XX XX XXX XXXX
(1)
(2)
(3)
(4)
(1) Manufacturer’s Identification Mark
– CONTINUED – 13-3
Consumer information and Reporting safety defects
(2) Tire Size (3) Tire Type Code (4) Date of Manufacture The first two figures identify the week, starting with “01†to represent the first full week of the cal- endar year; the second two figures represent the year. For example, 0101 means the 1st week of 2001. (cid:84) Other markings The following makings are also placed on the sidewall. (cid:86) Maximum permissible inflation pressure The maximum cold inflation pressure to which this tire may be inflated. For example, “300 kpa (44 PSI) MAX. PRESS†(cid:86) Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 580 kg (1279 LBS) @ 300 kpa (44 PSI) MAX. PRESS.â€
13-4
Maximum load rating applies only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehi- cle can be loaded up to the tire’s rated load.
(cid:86) Construction type Applicable construction of this tire. For example, “TUBELESS STEEL BELTED RA- DIAL†(cid:86) Construction The generic name of each cord material used in the plies (both sidewall and tread area) of this tire. For example, “PLIES: TREAD 2 STEEL + 2
POLYESTER SIDEWALL 2 POLYESTER†(cid:86) Uniform Tire Quality Grading (UTQG) For details, refer to “Uniform tire quality grading standards†in this chapter.Consumer information and Reporting safety defects
(cid:132) Recommended tire inflation pressure (cid:84) Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire size Wheel size Pressure
Item
Front
Rear
Temporary spare tire
Size Pressure
RS, RS sport package, WRX P205/55R16 89V
16 × 61/2 JJ 2.2 kgf/cm2)
32 psi (220 kPa,
29 psi (200 kPa,
2.0 kgf/cm2)
WRX (option tire)*1
WRX-STi
215/45R17 87W 225/45R17 90W
17 × 7 JJ
33 psi (230 kPa,
2.3 kgf/cm2)
32 psi (220 kPa,
2.2 kgf/cm2)
17 × 8 JJ
36 psi (250 kPa,
2.5 kgf/cm2)
30 psi (210 kPa,
2.1 kgf/cm2) T135/70 D17
T135/70 D16
60 psi (420 kPa, 4.2 kgf/cm2)
*1: The recommended cold tire pressure for the 215/45R17 87W tire is not indicated on the vehicle plac- ard attached to the driver’s side B-pillar since this tire is a dealer option for the WRX. If your vehicle is equipped with 215/45R17 87W tires, be sure to adjust them to the air pressure shown on this page.
– CONTINUED – 13-5
Consumer information and Reporting safety defects
(cid:84) Vehicle placard
Example:
614- ), ),1/ 1.4)61
5-)61/ +)2)+16; 66) #
.46 4-)4 !
6DA ?>EA@ MAECDJ B ??KF=JI =@ ?=HC IDK@ ALAH AN?AA@ " &C H ' >I
ORIGINAL TIRE SIZE
P205/55R16
COMPACT SPARE TIRE
+, 614- 1.)61 24-554-
.46
4-)42=! 251
2= '251+, 614- 1.)61 24-554-
T135/70D16
" 2= $ 251
SEE OWNER’S MANUAL FOR
ADDITIONAL INFORMATION MD
UGD513AA
The vehicle placard shows original tire size, rec- ommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and loading information. (cid:84) Adverse safety consequences of under-in-
flation
Driving at high speeds with excessively low tire pressures can cause the tires to flex severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and failure of the tire(s). Possible resulting loss of ve-
The vehicle placard is affixed to the driver’s side B-pillar.
UGD502BA
13-6
hicle control could lead to an accident. (cid:84) Measuring and adjusting air pressure to
achieve proper inflation
Check and, if necessary, adjust the pressure of each tire (including the spare) at least once a month and before any long journey. Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the specific values. Driving even a short distance warms up the tires and increases the tire pres- sures. Also, the tire pressures are affected by the outside temperature. It is best to check tire pres- sure outdoors before driving the vehicle. When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure.
(cid:132) Glossary of tire terminology (cid:121) Cold tire pressure The pressure in a tire that has been driven less than 1 mile or has been standing for three hours or more. (cid:121) Maximum inflation pressure
Consumer information and Reporting safety defects
The maximum cold inflation pressure to which a tire may be inflated. (cid:121) Recommended inflation pressure The cold inflation pressure recommended by a vehicle manufacturer. (cid:121) Intended outboard sidewall
1)The sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or 2)The outward facing sidewall of an asymmet- rical tire that has a particular side that must al- ways face outward when mounting on a vehi- cle.
(cid:121) Accessory weight The combined weight (in excess of those stan- dard items which may be replaced) of floor mats, leather seats and cross bars to the extent that these items are available as factory-installed equipment (whether installed or not). (cid:121) Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fu- el, oil, and coolant and air conditioning.
– CONTINUED – 13-7
Consumer information and Reporting safety defects
(cid:121) Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehi- cle capacity weight and production options weight. (cid:121) Normal occupant weight 150 lbs (68 kg) times the number of occupants (3
occupants). (cid:121) Occupant distribution Distribution of occupants in a vehicle, 2 in front, 1 in rear seat. (cid:121) Production options weight The combined weight of those installed regular production options weighing over 5.1 lbs (2.3 kg) in excess of those standards items which they replace, not previously considered in curb weight or accessory weight. (cid:121) Vehicle capacity weight The total weight of cargo, luggage and occu- pants that can be added to the vehicle. (cid:121) Vehicle maximum load on a tire Load on an individual tire that is determined by distributing to each axle its share of the maxi- mum loaded vehicle weight and dividing by two. (cid:121) Vehicle normal load on a tire Load on an individual tire that is determined by13-8
distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by two.
(cid:132) Tire care – maintenance and safety
practices
(cid:121) Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. (cid:121) Inspect the tire tread regularly and replace the tires before their tread wear indicators become visible. When a tire’s tread wear indicator be- comes visible, the tire is worn beyond the ac- ceptable limit and must be replaced immediately. With a tire in this condition, driving at even low speeds in wet weather can cause the vehicle to hydroplane. Possible resulting loss of vehicle control can lead to an accident. (cid:121) To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,500 km). Rotating the tires involves switching the front and rear tires on the right hand side of the vehicle and similarly switching the front and rear tires on the
left hand side of the vehicle. (Each tire must be kept on its original side of the vehicle.) Replace any damaged or unevenly worn tire at the time of rotation. After tire rotation, adjust the tire pres- sures and make sure the wheel nuts are correct- ly tightened. A tightening torque specification and a tightening sequence specification for the wheel nuts can be found “Flat tires†in Chapter 9.
(cid:132) Vehicle load limit – how to determine The load capacity of your vehicle is determined by weight, not by available cargo space. The load limit of your vehicle is shown on the vehicle placard attached to the driver’s side B-pillar. Lo- cate the statement “The combined weight of oc- cupants and cargo should never exceed XXX kg or XXX lbs†on your vehicle’s placard. The vehicle placard also shows seating capacity of your vehicle. The total load capacity includes the total weight of driver and all passengers and their belong- ings, any cargo, any optional equipment such as a trailer hitch, roof rack or bike carrier, etc., and the tongue load of a trailer. Therefore cargo ca-
Consumer information and Reporting safety defects
pacity can be calculated by the following method. Cargo capacity = Load limit – (total weight of oc- cupants + total weight of optional equipment + tongue load of a trailer (if applicable)) For towing capacity information and weight lim- its, refer to “Trailer towing†in Chapter 8. (cid:84) Calculating total and load capacities vary-
ing seating configurations
Calculate the available load capacity as shown in the following examples: Example 1A
UGD504BA
– CONTINUED – 13-9
Consumer information and Reporting safety defects
Vehicle capacity weight of the vehicle is 900 lbs (408 kg), which is indicated on the vehicle plac- ard with the statement “The combined weight of occupants and cargo should never exceed 900
lbs or 408 kgâ€. For example, if the vehicle has one occupant weighing 154 lbs (70 kg) plus cargo weighing 662 lbs (300 kg). 1. Calculate the total weight.Total weight = 154 lbs (70 kg) + 662 lbs (300 kg)
(Occupant)
(Cargo)
= 816 lbs (370 kg) 2. Calculate the available load capacity by sub- tracting the total weight from the vehicle capacity weight of 900 lbs (408 kg).
13-10
Available Load Capacity = 900 lbs (408 kg) – 816 lbs (370 kg)
(Vehicle
capacity weight)
(Total weight)
= 84 lbs (38 kg) 3. The result of step 2 shows that a further 84 lbs (38 kg) of cargo can be carried. Example 1B
For example, if a person weighing 176 lbs (80
kg) now enters the same vehicle (bringing theHG8014BA
Consumer information and Reporting safety defects
number of occupants to two), the calculations are as follows: 1. Calculate the total weight.
Example 2A
Total weight = 154 lbs (70 kg) + 176 lbs (80 kg)
(Occupant)
+ 662 lbs (300 kg)
(Cargo)
= 992 lbs (450 kg)
2. Calculate the available load capacity.
Available Load Capacity = 900 lbs (408 kg) – 992 lbs (450 kg)
(Vehicle
