Login- Download PDF Manual
-
Display
Control mode
Black plate (169,1)
Audio 5-5
VOL
BAS
TRE
BAL
FAD
Volume control
Bass control
Treble control Balance control
Fader control
Turn counterclockwise
Turn clockwise
For less volume
For less bass sound
For less treble sound
For more volume
For more bass sound
For more treble sound
To increase left speaker volume and de- crease right speaker volume
To increase rear speaker volume and decrease front speaker volume
To increase right speaker volume and decrease left speaker volume To increase front speaker volume and decrease rear speaker volume
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-6 Audio
! FM/AM band selection button
(BAND)
Push the “BAND” button when the radio is on to select FM1, FM2 or AM band reception. Each time this button is pressed, the band will change in the following order:
The display indicates which one is cur- rently selected. ! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. ! Tuning (TUNE) ! Manual tuning (TUNE) Push the “ ” side of the tuning button (3) to increase the tuning frequency and press the “ the button to decrease it. Each time the button is pressed, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM wave- band. ! Seek tuning If is pressed for longer than half of a second, the radio will begin to automatically search for receiva-
the tuning button (3)
” side of
tuning to select
ble frequencies and will stop at the first one found. This function may not be available, however, when radio signals In such a situation, perform are weak. manual the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (6) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop- erly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (4) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset.
Black plate (170,1)
! How to preset stations 1. Press the “BAND” selection button to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (6) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (4) for at least 2 seconds to store the frequency. At this time, there will momentarily be no sound from the radio. the button is pressed for the preceding selection will remain in memory.
less than 2 seconds,
If
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. this occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
If is necessary to reset
it
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Compact disc player operation
Black plate (171,1)
Audio 5-7
(7) Disc slot (8) CD button (9) Eject button (10) Fast-forwarding and track up button (11) Fast-reversing and track down button (12) Random button (13) Repeat button (14) Scan button (15) PWR (power) switch
! To play back a compact disc ! When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A single CD (8 cm/3 inch CD) may also be used without any adapter. NOTE . Make sure to always insert a disc If a disc is with the label side up. inserted with the label side down, it might be ejected or the player might shut off. . After the last song finishes, the player will automatically return to track 1 (the first song on the disc).
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-8 Audio
! When CD is in the player Press the “CD” button (8). The display will show “CD-IN” and the player will start playback. NOTE After the last song finishes, playback will automatically return to track 1 (the first song on the disc). ! To stop playback of a CD When the “PWR” button (15) is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. ! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track number will decrease.
” side of
” side of
the button (11)
the button (10)
! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Briefly press the “RPT” button (13) while a song is playing to play the song repeat- edly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. ! Random playback Briefly press the “RAND” button (12) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. the random mode, press the To cancel button again. Then the “RAND” indicator goes out, and normal playback mode is restored.
Black plate (172,1)
! Scan Briefly press the “SCAN” button (14), and you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored. ! To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
” (9). The disc will be ejected.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& CD changer control (if optional in-dash CD changer is con-
nected)
An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or unload CDs). See your SUBARU dealer for more information.
Black plate (173,1)
Audio 5-9
(16) CD button (17) Track selection buttons (18) RAND (Random) button (19) RPT (Repeat) button (20) SCAN button
! To start playback When the “CD” button (16) is pressed, the CD changer will start playback. The dis- play shows the current disc number, track number and the elapsed time during playback. NOTE . If a disc is in the player, the “DISC” button is used to change from CD player operation to DISC changer op- eration. Each time the “DISC” button is pressed, the operating mode will change alternately. . At the end of the disc, the player automatically continues with the next disc. . After playback on the last disc finishes, playback will automatically return to the first disc. . If you have loaded fewer than 6
discs, any missing disc is automati- cally skipped.– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-10 Audio
! Selection of a desired disc You can select a desired disc from among the discs contained in the CD changer only by pressing the corresponding num- ber on one of the disc select buttons. If you are to listen to the 5th disc in the CD changer, press the “5” button of the disc select buttons. All other discs in the CD changer can also be selected in a similar way. NOTE . No disc change takes place if the button corresponding to the storage tray in which no disc is loaded is pressed. . If the disc select button correspond- ing to the disc now in playback is pressed again, the disc will be replayed from its beginning. ! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the current
the disc,
” side of
the button (17)
track. Each time this side of the button is pressed, the indicated track number will decrease. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. If you continue fast-forwarding to the end of the CD changer will auto- matically stop fast-forwarding and start playback beginning with the first track on the current disc. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. If you continue fast-reversing to the beginning of the disc, the CD changer will automatically stop fast-reversing and start playback beginning with the first track on the current disc. ! Repeat playback Press the “RPT” button (19) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and
the button (17)
” side of
Black plate (174,1)
normal playback mode is restored. ! Random playback Press the “RAND” button (18) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored. ! Scan (a convenient way to become
familiar with a disc)
1. Press the “SCAN” button (20). – The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all programs. Then, normal playback starts. 2. Press the “SCAN” button again when you hear a track you like. – Normal playback resumes.
! To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Type B audio set (if equipped)
The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation
Black plate (175,1)
Audio 5-11
(1) Power switch, Volume, Brightness con-
trol dial
(2) FM/AM selection button (3) Seek button (4) Scan button (5) Sound/Tune control dial (6) Preset buttons
! Power switch and volume/bright-
ness control (POWER/VOL/ BRIGHT)
The dial (1) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial, and the volume is controlled by turning the dial. ! Sound control and tune/folder se-
lect/channel control (SOUND/TUNE/ FOLDER/CH)
The dial (5) is used for selecting the sound control mode with each brief press of the dial, and for adjusting each level by turning it. It is also used for tuning the radio/folder selection (only when playing MP3 or WMA)/channel selection (satellite radio*) when the “FM/AM”, “CD/AUX” and “SAT” are selected. (*: Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer.)
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (176,1)
5-12 Audio
Display
Control mode
BASS
MIDDLE
TREBLE
FADER
BALANCE
VOLUME
Bass control
Midrange control
Treble control Fader control
Balance control
Turn counterclockwise
Turn clockwise
For less bass sound
For more bass sound
For less midrange sound
For more midrange sound
For less treble sound
For more treble sound
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
To increase left speaker volume and de- crease right speaker volume
To increase right speaker volume and decrease left speaker volume
Volume control
For less volume
For more volume
! Sound control The dial (5) controls the Bass, Midrange, Treble, Balance and Fader when you select the appropriate sound control mode. Choose the desired setting for each mode by depressing the “SOUND” control dial function
(5). The control
returns to last mode after approximately 5 seconds. To change control modes: Each brief press of the “SOUND” button (5) changes control modes in the following sequence starting from bass control mode.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
! Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims when the light switch is in the “ ” or “ ” position. If this makes the display difficult to read, press the volume dial for more than 2 seconds to return the display to original brightness. Subsequently pressing the volume dial again for more than 2 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” position makes the radio display dim again. ! FM/AM selection button (FM/AM) Push the “FM/AM” button (2) when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:
” or “
The display indicates which one is cur- rently selected. ! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. ! Manual tuning (TUNE) Turn the tuning dial (5) clockwise to increase the tuning frequency and turn
the dial counterclockwise to decrease it. Each click the dial is turned, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM waveband. ! Seek tuning When the “ ” side of the “SEEK/TRACK/ CAT” button (3) is depressed, the radio will begin to automatically seek up for recei- vable frequencies and will stop at the first one found. For the “ ” side, the radio will begin to automatically seek down. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (4) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at a receivable station for 5 seconds while displaying the frequency by blinking, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may
Black plate (177,1)
Audio 5-13
not function properly if the station recep- tion is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (6) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. ! How to preset stations 1. Press the “FM/AM” button (2) to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (4) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (6) for at least 2 seconds to store the frequency. The frequency of the station will flash once on the display at this time.
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the this preset buttons are cleared. occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit
If is necessary to reset
it
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (178,1)
5-14 Audio
noise when the phone receives calls. This noise does not indicate a problem with the radio.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Built-in CD changer control
Black plate (179,1)
Audio 5-15
(7) CD button (8) Eject button (9) Disc slot (10) Track selection buttons (11) Repeat/Random button (12) Disc number indicator (13) Load button (14) Folder selection dial (15) Disc selection buttons (16) Display button
NOTE . Make sure to always insert a disc If a disc is with the label side up. inserted with the label side down, it might be ejected or the player might shut off. . If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. . The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones. . 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected.
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (180,1)
5-16 Audio
it means that
! How to insert a CD(s) ! Inserting a CD 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the If no indicator idle position will blink. blinks, there is no idle position in the magazine. 2. When “IN” is displayed, insert the disc. Once you have inserted the disc, the disc number indicator will stop blinking. The disc will be then automatically drawn in, and the player will begin to play back the first track of the disc. . To insert more discs in succession, repeat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc within 15 seconds after you have pressed the “LOAD” button and “IN” is displayed, the player will begin to play back the first track of the last disc you have inserted. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter the standby mode. Press the “CD/AUX” button (7) to start playback.
! Inserting a disc in a desired position 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator (12) associated with the idle position will blink. 2. Press the disc selection button (15) at the position where you want to insert a disc. The associated disc number indica- tor will blink. 3. If you insert a disc during the 15- second period while “IN” is displayed, the disc will be automatically drawn in, and the player will start playback of the disc, beginning with the first track. . To insert more discs in succession, repeat Steps 1 and 3. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter standby mode. Press the “CD/AUX” button (7) to start playback.
! Loading all the magazine (Full disc
loading mode) If you continue to press the “LOAD” 1. button (13) for more than 2 seconds, the player will enter the full disc loading mode. 2. The disc number indicator (12) asso- ciated with the idle position will blink. The magazine will be loaded with discs in the
ascending order of position number. 3. When the loading of a disc is com- plete, the next disc number indicator (12) will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15-second interval, the full disc loading mode will be can- celed, and the player will start playback of the disc inserted first.
! How to play back a CD or make a
pause
! When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first track. ! When there are CDs loaded: Depress the “CD/AUX” button to turn on the CD (when the last mode of the player is CD) and press a desired one of the disc select buttons (15). The player will then start playback of the selected CD, begin- ning with the first track.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
! To select a track from its beginning ! Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the current track. Each time the button is pressed, the indicated track number will decrease. ! To select a folder (for MP3/WMA
audio)
” side of
Turn the “TUNE/FOLDER/CH” dial (14) to select the folder. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ the button (10) continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ the button (10) continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Depress the “RPT/RDM” button (11) while a song is playing to play the song
” side of
repeatedly. Each time this button is pressed, the repeat play mode will change in the following order:
The “RPT” indicator will come on and the song will be played continuously. When the “RPT” the repeat OFF is selected, indicator goes out and normal playback mode is restored. . The repeat play mode will be can- celled if you perform any of the follow- ing steps:
– Press the “RPT/RDM” button to select the repeat OFF. – Press the eject button. – Press the “LOAD” button. – Select the radio mode. – Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position. ! Random playback Press the “RPT/RDM” button (11) for more than 2 seconds while a disc is being played back to play all songs on the disc in a random order.
Black plate (181,1)
Audio 5-17
The “RDM” indicator will come on and all songs on the disc will be played in a random order. When the random OFF is the “RDM” indicator goes out selected, and normal playback mode is restored. . The random play mode will be cancelled if you perform any of the following steps:
– Press the “RPT/RDM” button to select the random OFF. – Press the eject button. – Press the “LOAD” button. – Select the radio mode. – Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position.
! How to unload CDs from the player ! Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the disc select button (15) of the disc whose disc number indicator (12) is ON. 2. Press the eject button (8). Then the disc number indicator associated with the
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-18 Audio
disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1 and 2. If you press the eject button after turning OFF the ignition switch, only one disc will be ejected.
! Ejecting all discs from the player (All
disc ejection mode) If you continue to press the eject 1. button (8) for more than 2 seconds, the player will enter the all disc ejection mode. 2. Remove the disc that has been the display indicates “CD ALL ejected, EJECT” (when the ignition switch is in the “Acc” position) and disc indicator will blink. The other discs loaded will then be ejected one after another. If you do not remove the ejected disc within 15 sec- onds, the “All disc ejection mode” will be canceled.
NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
CAUTION
Do not attempt to insert two or more discs into the slot at a time. Doing
so can cause mechanical damage to the CD changer.
! Title display selection If you briefly press the “DISP” button (16) during playback, the indication will change to the next one in the following sequence. . For MP3/WMA:
. For Satellite radio:
The display mode that you selected will not be changed until you select the display mode again. When you depress the “DISP” button for more than 2 seconds, the title will be scrolled so you can see all of it. You will see 12 characters at a time. . The page scroll mode will be can- celled if you perform any of the follow- ing steps:
– When you do not operate any button within 10 seconds. – Press any button to select an- other play mode. – Press the eject button.
Black plate (182,1)
– Press the disc selection button. – Select the radio mode. – Press the “ – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position.
” button.
” or “
NOTE When the disc has no title, the display indicates “NO TITLE”. ! When the following messages are
displayed
the following messages is If one of displayed while operating the CD player, determine the cause based on the follow- ing information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed This message means that there is a mechanical error. Depress the eject button to unload the disc. Check the disc for damage or deformation, and also check that the correct disc is inserted. Do not try to unload the disc forcibly. 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected and this the disc message will be displayed. cannot be unloaded or the message
If
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
remains displayed, please contact your SUBARU dealer. ! When “CHECK DISC” is displayed Press the eject button to unload the discs. Check that the disc is not damaged or scratched, and also check that the disc is inserted correctly. Some CD-RW discs may be causing this message to appear. Check that the disc type (i.e., 8 cm/3 inch CDs are not supported) and data format are correct. This player can only play MP3
and WMA data formats. If the disc cannot be unloaded or the message remains displayed, please contact your SUBARU dealer.Black plate (183,1)
Audio 5-19
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-20 Audio
& Auxiliary unit and satellite radio operation
Black plate (184,1)
(17) AUX button (18) Category button (19) Scan button (20) Satellite radio* button (21) Category selection button (22 Preset buttons (23) Channel selection dial
(*: Use of satellite radio requires a tuner, antenna and a service contract. For de- tails, please contact your SUBARU deal- er.) NOTE . For use of the In-dash CD changer, refer to the section of “In-dash 6 CD auto changer” in this chapter. . Use of satellite radio requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer. . The “AUX mode” can be used when the appropriate device is connected to the AUX jack. . The output sound of the portable audio player is not loud, and the sound via the vehicle’s speakers that are connected to the vehicle audio set is very quiet. If you turn up the volume of the audio set, the volume becomes louder. However, when you change the audio to the radio mode or to a CD player, the sound becomes a lot louder. Remember to turn down the
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
volume when you change between them. ! AUX audio jack (if equipped) The AUX (auxiliary) audio jack is located behind the lid under the climate controls. Push gently on the lid to open it.
! Satellite Radio mode (if equipped) Press the “SAT” button (20) to select the “Satellite radio mode” (when the SR-BB is connected). ! Sirius satellite radio Sirius satellite radio is a recent innovation that allows the listener to experience digital sound quality and to have a greater variety of channels to choose from (more than 160 channels with the relevant subscription). Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer or visit Sirius Satellite Radio at www.sirius.com or call 1-888-539-SIRIUS (7474) for more information. Sirius, the Sirius dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. ! Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may obstruct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result loss include driving near a wall, steep cliff or hill, or driving on the lower level of a multi- tiered road or inside a parking garage.
in signal
Black plate (185,1)
Audio 5-21
To help reduce this condition, satellite radio providers have installed ground- based repeaters in heavily populated areas. However, you may still experience reception problems in some areas. ! Displaying satellite radio ID of tuner When you activate satellite radio, you should have your satellite radio tuner ID ready because each tuner is identified by its unique satellite radio tuner ID. The satellite radio ID will be needed when you activate satellite radio and receive satellite radio customer support. The satellite radio ID can be found on the audio display by tuning the channel to “0”. Turn the “TUNE/FOLDER/CH” dial (23) to select the satellite radio channel. ! Channel selection Turn the “TUNE/FOLDER/CH” dial (23) to select the radio channel. Turn the tuning dial clockwise to change the channel upward and turn the dial counterclockwise to change the channel downward with each click of the dial. ! Category selection Press the “SEEK/TRACK/CAT” button (18) radio channel. Press the “ ” side of the button (18) to change the category upward and the “ ” side of the button to downward – CONTINUED –
the category of
to select
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
selection, channel scan) are performed only in the selected category. To cancel the category mode, press the “CAT” button (21) for at least 2 seconds again. ! Band selection Push the “SAT” button (20) when the radio is on to select SR1, SR2 or SR3 reception. Each time this button is pressed, the band will change in the following order:
! AUX mode Press the “CD/AUX” button (17) to select the “AUX mode” (when the AUX unit is connected to the AUX jack).
5-22 Audio
with each press of the button. ! Channel preset Presetting a channel with a preset button (22) allows you to select that station in a single operation. Up to six SR1, SR2 and SR3 channels each may be preset. Press one of the preset buttons for at least 2 seconds to store the channel. The number of the channel will flash once on the display, and the unit produces a beep sound at this time. ! Channel scan Press the “SCAN” button (19) to change the radio to the SCAN mode. In this mode, the radio scans through the channel until a station is found. The radio will stop at the station for 5 seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Press the “SCAN” button (19) again to cancel the SCAN mode and to stop on any displayed station. When the “SCAN” button is pressed for automatic tuning, stations are only scanned in an upward direction. ! Category mode Press the “CAT” button (21) for at least 2
seconds to turn the category mode on. In this mode, the radio operations (channelBlack plate (186,1)
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
In-dash 6 CD auto changer (if equipped) & Loading and unloading compact discs
Black plate (187,1)
Audio 5-23
(1) Disc slot (2) Disc indicators (disc No.1 to 6) (3) Disc select buttons (disc No.1 to 6) (4) Eject button (5) Disc slot indicator
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-24 Audio
CAUTION
. Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer.
. Use only music CDs identified by
mark.
. Do not use CDs listed in the following which could cause da- mage to the CD player. – 3 inch (8 cm) compact disc – Any disc with a peel-off or seal
on it
– Bent disc – Cleaning disc – CD accessory (e.g., 3 inch (8
cm) disc adapter)
. Do not insert or remove any disc when the automatic transmission selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).
Black plate (188,1)
! To insert a disc 1. Press one of the disc select buttons (3) (numbered from 1 to 6) for which the disc indicator light (2) is “OFF”. The disc indicator lights are located directly above the corresponding disc select buttons. 2. The indicator will begin blinking. The blinking will last for 15 seconds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” (1) door will close. Repeat Step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat Steps 1
and 2 choosing a different disc select button.! To insert six discs at a time 1. Press and hold the disc select button number 1 until all disc indicators begin blinking (approximately 1.5 seconds). 2. The indicators will blink for 15 sec- onds. During this period, insert desired six discs. the first 3. When all discs are loaded, disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.)
! To remove a disc 1. Press the desired one of the disc select buttons (3) (numbered from 1 to 6) for which the disc indicator light is on. 2. Press the eject button (4). The se- lected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat Steps 1 and 2 choosing a different disc select button. (To remove discs when the ignition switch is in the “Lock” position, press the eject button, and the first disc will be ejected. Press the eject button again, and the next disc will be ejected and so on. At this time, the disc select buttons are disabled.)
! To remove all discs at one time 1. Press and hold the eject button (4) until all “Disc” indicators begin blinking (approximately 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on.
! To replace a playing disc with
another
Simply press the desired one of disc select buttons (3) (numbered from 1 to 6) or press the disc select button on the radio unit to select the desired disc, and the disc
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
will begin to play. ! Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode. OFF: No disc is loaded or the ignition switch is in the “LOCK” position. ! Open/Closed disc slot indicator When the disc slot is open, indicators on both sides of illuminate. ! Function control Refer to CD changer control operating instructions described in the “Type A audio set” section.
the disc the slot
Precautions to observe when handling a compact disc
Use only compact discs (CDs) that have the mark shown in the following illustra- tion.
You may also use compact discs (CD-Rs and CD-RWs) that have the following marks, but you may not use some discs if they were produced using writing meth- ods not compatible with your vehicle’s audio system.
Black plate (189,1)
Audio 5-25
. You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-26 Audio
If
normal operation. this happens, eject the CD and wait for the player to dry out. . Skipping may occur when the CD player is subjected to severe vibration (for example, when the vehicle is driven on a rough surface). . To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamination could cause poor tone quality. Do not touch the disc surface. . Use a clean disc whenever possible. If there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzene, alcohol, etc. . Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-standard shape (for example, a heart shape). Malfunctions or problems might result. . A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or on hot days.
Black plate (190,1)
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Interior lights ....................................................... Dome light .......................................................... Cargo area light .................................................. Map lights ............................................................ Sun visors ........................................................... Vanity mirror ....................................................... Storage compartments ....................................... Glove box ........................................................... Center console.................................................... Overhead console ............................................... Dashboard storage compartment ......................... Convenience net ................................................. Pocket (if equipped) ............................................ Cup holders ......................................................... Front passenger’s cup holder .............................. Rear passenger’s cup holder ...............................
6-2
6-2
6-2
6-3
6-3
6-3
6-4
6-4
6-4
6-6
6-6
6-6
6-7
6-7
6-7
6-8Black plate (11,1)
Interior equipment
Accessory power outlets ....................................
6-8
Use with a cigarette lighter
(Canada only, if equipped)................................ Ashtray (Canada only, if equipped) .................. Floor mat ............................................................ Coat hook........................................................... Cargo area cover (if equipped) ......................... Using the cover ................................................. To remove the cover housing............................. Stowage of the cover ......................................... To install the cover housing ............................... Shopping bag hook ........................................... Cargo tie-down hooks ....................................... Cargo area bars ................................................. Under-floor storage compartment ....................
Front, left and right side storage
compartment ...................................................
Center storage compartment
(Storage bucket) ..............................................
6-10
6-11
6-12
6-12
6-13
6-13
6-13
6-13
6-13
6-14
6-14
6-14
6-156-16
6-16
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (192,1)
6-2 Interior equipment
Interior lights
When leaving your vehicle, make sure the light goes out to avoid battery discharge.
& Dome light
about 30 minutes later and then the light is turned off automatically. The light also can be turned on by use of the keyless entry transmitter. See the “Remote keyless entry system” section in chapter 2 for detailed information. OFF: The light stays off.
& Cargo area light
NOTE If a door or the rear gate is left open, the light flashes and a chime sounds about 30 minutes later and then the light is turned off automatically. The light also can be turned on by use of the keyless entry transmitter. See the “Remote keyless entry system” section in chapter 2 for detailed information.
The dome light switch has three positions:
ON: The light stays on continuously. DOOR (middle position): The dome light comes on when any of the doors or the rear gate is opened. The light remains on for several seconds and gradually goes out after all doors and the rear gate are closed. NOTE If a door or the rear gate is left open, the light flashes and a chime sounds
The cargo area light switch has three positions:
ON: The light stays on continuously. OFF: The light stays off. DOOR: The light comes on only when the rear gate is opened.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Map lights
Sun visors
& Vanity mirror
Black plate (193,1)
Interior equipment 6-3
To turn on the map light, push the switch. To turn it off, push the switch again.
When leaving the vehicle, make sure the light to avoid battery dis- charge.
is turned off
To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (194,1)
6-4 Interior equipment
Storage compartments
& Glove box
To use as armrest:
CAUTION
. Always keep the storage com- partment closed while driving to reduce the risk of injury in the event of sudden stops or an accident.
. Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.
Lock
1) 2) Unlock
1. Tip the console top forward from its vertical position.
To open the glove box, pull the handle. To close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clockwise.
& Center console The center console box provides a sto- rage space. the console can be used as an armrest and as a rear passenger’s cup holder.
In addition,
the top of
2. Push the armrest part of the console top forward to the desired position while pulling up the knob at the front end of the
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
the position of
armrest and lock it in position by releasing the knob. Adjust the armrest to suit your driving position. Make sure the armrest is securely retained. When you slide the armrest back to its original position, pull the knob upward as you do so. To return the console top to the vertical position, pull upward the knob at the front end of the armrest while raising the console top until it emits a click.
CAUTION
Do not step or sit on the armrest, and do not place heavy objects on it. The armrest could break, and you could get hurt.
To use as rear passenger’s cup holder:
Black plate (195,1)
Interior equipment 6-5
fall from the table and cause a burn or other injury.
To use as storage space:
With the console top tipped toward the rear seat, it can be used as a cup holder.
CAUTION
. To switch from using the console top as an armrest to using it as a rear passenger’s cup holder, raise the console top to the vertical position before tipping it toward the rear seat. Otherwise the console top may break.
. Do not place any object weighing more than 4.4 lbs (2 kg) on the table.
. Do not have hot drinks or other objects on the table while driv- ing. During hard braking or ne- gotiation of a curve, they could
Raise the console top to the vertical toward the rear seat. position or tip it Then, pull up the lock button of the console box and open the lid. When closed, the lid can be used as a tray for placing small items in it.
CAUTION
. Before opening the lid of
the console box, raise the console top completely to the vertical position or tip it toward the rear seat. Otherwise, the lid may be damaged and an injury may oc-
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (196,1)
6-6 Interior equipment
cur.
. Be careful not to trap your hands between the console top and console box when raising and tipping the console top.
. When there is an object on the console box lid, do not tip the console top forward. Otherwise, the console top or lid could be damaged, and an injury could occur.
& Overhead console
CAUTION
CAUTION
When your vehicle is in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulner- able or flammable articles such as a lighter in the overhead console.
When your vehicle is in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulner- able or flammable articles such as a lighter in the overhead console.
& Dashboard storage compart-
ment
& Convenience net
To open the console, push on the console lid lightly and the lid will automatically open.
To open the dashboard compartment, push the button on the lid and the lid will automatically open. Be sure to close the compartment fully before driving.
A net for storing small articles is provided at the front passenger’s foot-well.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Pocket (if equipped)
Cup holders
CAUTION
. When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an accident.
. Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident.
. Take care to avoid spills. Bev- erages, if hot, might burn you or your passengers. Spilled bev- erages may also damage uphols- tery or carpets.
CAUTION
Do not use the pocket as an ashtray or leave a lighted cigarette in the pocket. This could cause a fire.
To use the pocket, push lightly on the lid below the climate controls.
Black plate (197,1)
Interior equipment 6-7
& Front passenger’s cup holder ! In front door trim
The door pockets can be used to hold beverage bottles and other items.
CAUTION
When placing a beverage in a door pocket, make sure it is capped. Otherwise, the beverage could spill when opening/closing the door or while driving and, if the beverage is hot, it could scald you.
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
6-8 Interior equipment
! In center console
A dual cup holder is built in the center console, beside the parking brake lever. & Rear passenger’s cup holder There are rear passenger’s cup holders at the back of the center console as well as on the reverse side of the console top. To use the rear passenger’s cup holder located at the back of the center console, open the lid by pulling its upper edge.
To use the rear passenger’s cup holder located on the reverse side of the console top, in the “Storage compartments” part of this chap- ter for details.
to “Center console”
refer
Black plate (198,1)
Accessory power outlets
Power outlet beside front pocket
Power outlet in center console
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
or more outlets simultaneously, the total power consumed by them must not exceed 120W.
CAUTION
. Do not attempt to use a cigarette lighter in the center console and cargo area power outlets.
. Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Al- ways put the cap on the acces- sory power outlet when it is not in use.
. Use only electrical appliances which are designed for 12V DC. The maximum power rating of an appliance that can be connected varies among outlets as shown in the following. Do not use an appliance which exceeds the in- dicated wattage for each outlet. Outlet beside front pocket: 80W or less Outlets in center console and cargo area: 120W or less When using appliances con- nected to two or more outlets
Power outlet in cargo area
(12V DC)
Accessory power outlets are provided beside the front pocket, in the center console and in the cargo area. Electrical power from the battery is available at any of the outlets when the ignition switch is in either the “Acc” or “ON” position. You can use an in-vehicle electrical appliance by connecting it to an outlet. The maximum power rating of an appli- ance that can be connected varies among outlets as shown in the following. Do not use an appliance which exceeds the indicated wattage for each outlet. Outlet beside front pocket: 80W or less Outlets in center console and cargo area: 120W or less When using appliances connected to two
Black plate (199,1)
Interior equipment 6-9
simultaneously, the total power consumed by them must not exceed 120W. Overloading the accessory power outlet can cause a short circuit. Do not use double adapters or more than one electrical appliance.
. If the plug on your electric appli- ance is either too loose or too tight for the accessory power outlet, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly.
. Use of an electric appliance in the accessory power outlet for a long period of time while the engine is not running can cause battery discharge.
. Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accel- erator and brake pedals. If they do, do not use the electrical appliance while driving.
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
6-10 Interior equipment
& Use with a cigarette lighter (Canada only, if equipped)
NOTE When the lid of the center console is closed, an opening remains between the center console and the lid to allow the power outlet in the center console to be used. Pass the electrical appli- ance’s cord through this opening.
To use the accessory power outlet beside the front pocket as a cigarette lighter socket, purchase the cigarette lighter plug, which is an optional accessory. A cigarette lighter plug is available from your SUBARU dealer. The cigarette lighter operates only when the ignition switch is in the “ON” and “Acc” positions. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use.
Black plate (200,1)
WARNING
To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage the heating element.
CAUTION
. Do not hold the lighter pushed in,
because it will overheat.
. The electrical power socket lo- cated on the lower part of the instrument panel is originally de- signed to use a genuine SUBARU cigarette lighter plug. Do not use non-genuine cigarette lighter plugs in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire.
. If the socket is ever used for a plug-in accessory such as a cell phone, that may damage the portion of the socket’s internal mechanism that causes a cigar- ette lighter plug to “pop out” after its lighter element is heated. Therefore, do not place a cigar- ette lighter plug in a socket that has been used, even once, to
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
power a plug-in accessory. Doing so may cause the plug to stick and overheat, creating a potential fire hazard.
Ashtray (Canada only, if equipped)
CAUTION
Do not use ashtrays as waste re- ceptacles or leave a lighted cigarette in an ashtray. This could cause a fire.
It is possible to install on ashtray, which is an optional accessory, in the front pocket. The ashtray is available from your SUBARU dealer. To open the ashtray, push lightly on the lid below the climate controls. Fully close the lid after using it to help reduce residual smoke.
Black plate (201,1)
Interior equipment 6-11
To remove the ashtray for cleaning, hold the right and left sides of the ashtray and pull it out. NOTE
Particles of ash and tobacco will accu- mulate around the hinges of the ash- tray’s inner lid. Clean them off using a toothbrush or other narrow-ended im- plement.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
6-12 Interior equipment
Floor mat
Black plate (202,1)
Coat hook
A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release. The floor mat is secured using the built-in grommet, by placing the grommet over the pin and pushing downward.
CAUTION
Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retain- ing pin. Also, do not use more than one floor mat. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.
The coat hook is attached to the rear left passenger’s hand grip.
CAUTION
Never hang anything on the coat hook that might obstruct the driver’s view or that could cause injury in sudden stops or in a collision. And do not hang items on the coat hook that weigh 2.2 lbs (1 kg) or more.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (203,1)
WARNING
& Stowage of the cover
Interior equipment 6-13
Cargo area cover (if equipped)
The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo.
& Using the cover
Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury.
& To remove the cover housing
To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.
1. Rewind the cover. 2. To take the cover housing off retainer, lift it out. 3. Store the cover housing in the cargo area.
the
On models having a temporary spare tire, the cargo area cover can be stowed under the cargo floor.
& To install the cover housing To install the cover, insert both ends of the cover housing into the retainers.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (204,1)
6-14 Interior equipment
Shopping bag hook
Cargo tie-down hooks
Cargo area bars
CAUTION
CAUTION
CAUTION
Do not hang items on the shopping bag hook that weigh 6.6 lbs (3 kg) or more.
In the cargo area, there are two retract- able shopping bag hooks (one on each side) and four non-retractable shopping bag hooks (two on each side).
The cargo tie-down hooks are de- signed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44
lbs (20 kg) per a hook.Do not place objects with a total weight exceeding 6.6 lbs (3 kg) on a net attached to the cargo area bars.
To use either of the retractable hooks, pull the lower portion out.
The cargo area is equipped with four tie- down hooks so that cargo can be secured with a cargo net or ropes. When using the hooks, raise them. When not in use, lower the hooks.
1) Cargo area bar
In the cargo area, there are two bars (one on each side) to which a net can be attached.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Under-floor storage compart- ment
small items.
CAUTION
. Always keep the lids closed while driving to reduce the risk of injury in the event of sudden stop or an accident.
. Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.
Black plate (205,1)
Interior equipment 6-15
There are five trays in the storage compartment underneath the floor of the cargo area. They can be used to store
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (206,1)
6-16 Interior equipment
& Front, left and right side storage compartment
& Center storage compartment
(Storage bucket)
To open the lid, raise the cargo tie-down hooks and pull the tab up. The jack and jack handle are stored in the left side storage compartment.
To open the lid, pull the handle up.
Canada-spec. non-turbo models: The storage bucket is put on the spare tire. Except Canada-spec. non-turbo mod- els: Storage tray is placed on the spare tire.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (207,1)
Interior equipment 6-17
NOTE When storing a flat tire, put the storage tray in the luggage compartment (ex- cept Canada-spec. non-turbo models).
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (2,1)
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Left Page
Model "ALL_MODEL_MEMO" EDITED: 2006/ 1/ 17
Fuel ...................................................................... Fuel requirements ............................................... Fuel filler lid and cap........................................... State emission testing (U.S. only)...................... Preparing to drive ............................................... Starting the engine.............................................. Manual transmission vehicle................................ Automatic transmission vehicle ........................... Stopping the engine............................................ Manual transmission...........................................
7-2
7-2
7-3
7-6
7-7
