2009 Saab 9 5 Owners Manual

Dome light, front 1 Ease the leading edge of the glass out

of the overhead panel.

2 Release one of the contacts and remove

the bulb.

Dome light, rear 1 Remove the entire overhead panel:

ease out the trailing end first, and then both front edges. 2 Fit the new bulb.

3 Fit the new bulb.

Glove-compartment illumination 1 Insert a small screwdriver in the slot in the end of the lamp fitting and ease it out to gain access to the bulb.

2 Bend out one of the contacts and

remove the bulb. 3 Fit the new bulb. On refitting, insert the connector-end of the lamp fitting first. Other bulbs If any other bulbs need changing, you are advised to take the car to a workshop. We recommend that you contact an authorized Saab dealer.

95_US_7carcare_MY09.fm Page 213 Tuesday, April 15, 2008 11:45 AM

Car care and technical information

213

10

Bulb table

Wattage # Cap 55 1 H7
2 H8 35
3 P21W 21

4 P21/5W 21/5
5 R10W 10

6 R5W 5 7 Xenon

w9U 8 T4W 9 WY5W/

W5W

10 W2W 1.2

NOTICE

Headlight Fog light Reversing lamp; rear fog lamp; rear direc- tion indicator Stop/tail lamp Dome light; courtesy lights; glove com- partment; luggage compartment Safety belt reminder; license-plate lighting Reading light, overhead panel

Reading light, rear Side indicators (yellow);/ high-mounted stop light (9-5 Sedan); parking lights Switches

Only fit lamps of the specified rating. Lamps of the wrong wattage could damage the wiring harness and electronics.

A special kit containing spare bulbs and fuses is available as an accessory from your Saab dealer. A storage space for this is pro- vided adjacent to the toolkit and jack, under the panel in the luggage compartment.

95_US_MY09.book Page 214 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

214
Fuses

WARNING

To avoid the risk of short-circuiting and/or fire breaking out in the electrical system, the following advice should be heeded: (cid:127) Always consult a workshop before modifying or adding any electrical equipment. We recommend that you contact an authorized Saab dealer. Failure to do so can result in the elec- trical system being damaged.

(cid:127) Never replace a fuse with one having a higher/lower rating than specified (see page 216). The color of the fuse indicates its amperage.

(cid:127) If the same fuse blows repeatedly,

have the electrical system checked by a workshop. We recommend that you contact an authorized Saab dealer. (cid:127) If a MAXI fuse blows, it means that

there is a major fault in the electrical system. Have the car checked by a workshop. We recommend that you contact an authorized Saab dealer.

Sound fuse / Blown fuse

The fuses are housed in two fuse panels: one at the end of the instrument panel on the driver’s side, and one under the hood. To check if a fuse has blown, first remove it from the panel (see below). If the filament is broken, the fuse has blown. A special tool for removing fuses is provided at the bottom of the fuse panel at the end of the instrument panel. Simply push the tool onto the fuse, squeeze and remove the fuse.

Fuse panel in instrument panel

Fuse box under the hood

95_US_MY09.book Page 215 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

215

DICE / TWICE DICE = Dashboard Integrated Central Elec- tronics TWICE = Theft-Warning Central Electronics DICE and TWICE are electronic control modules that monitor and control a variety of functions:

DICE controls (among other things): (cid:127) Front lights and interior lighting

Instrument illumination Intermittent wiper operation

(cid:127) Electric heating of rear window and door

mirrors

(cid:127) Cooling fans

Maxi fuses under the hood

Maxi fuses The Maxi fuses are housed in the fuse box under the hood. These fuses can be checked in the same way as the other fuses. The Maxi fuses are designed to protect the car’s electrical system from being dam- aged. Each Maxi fuse protects a number of electrical circuits and functions and there- fore has a higher rating (amperage) than the standard fuses. No spare Maxi fuses are supplied with the car.

NOTICE

If a Maxi fuse blows, it means that there is a major fault in the electrical system. Have the car checked without delay by a workshop. We recommend that you con- tact an authorized Saab dealer.

TWICE controls (among other things): (cid:127) Central locking. (cid:127) Car alarm (Anti-theft system) (cid:127) Engine immobilizer (cid:127) Autochecking of lights. (cid:127) Electric heating of rear seat (cid:127) Safety belt reminder (cid:127) Electrically adjustable passenger seat The DICE and TWICE control modules are linked to a data bus, which is basically an information carrier that allows information to be exchanged between all the control mod- ules and components connected to the bus. If a fault occurs in any of these components, diagnostic faults codes are set in the rele- vant control module, which facilitates fault diagnosis. We recommend that you contact an authorized Saab dealer. The scan tool connector for fault diagnosis is located under the instrument panel on the drivers side.

(cid:127) (cid:127) 95_US_MY09.book Page 216 Tuesday, April 15, 2008 11:03 AM

216

Car care and technical information

B C 1 2 3 4 5 6

6B

987

10

11

12

13

14

15 16

16B

17

18

19

20

21

22

23 24

25 26 27 28 29 30 31

32

33

34

35

36

37

38

39

Fuse panel in instrument panel

# Amp Function

Trailer lights Automatic transmission

30
10
7.5 Electric door mirrors; DICE: manual beam length

15

adjustment 3
Brake lights; Park Brake Shift Lock (cars with auto- matic transmission) Reversing lights Parking lights and taillights, left Parking lights and taillights, right

15
10
10
7.5 DICE / TWICE 30

Electric windows, right; trailer charging

10

15
15

6B

7.5 Brake lights, trailer 10
15

Engine injectors Trunk lighting; trunk lock; door lighting; parking assistant 3; SID Audio System; CD changer 3
Heating, rear seat 3; moonroof 3, remote control receiver Electrically adjusted passenger seat 3

30
11
7.5 Automatic transmission 3
12
Audio System, amplifier 20
13
Ignition system, engine 30
14
20
Fuel pump 15
DICE (direction indicators) 16
20
OnStar 3
16B – Engine-management system; main instrument; 17
20
DICE/TWICE Door-mirror heating; rear-window heating OnStar 3; Telematics 3
ACC; interior lighting; rear fog light; high beam flasher Audio System; rear-view mirror; load angle sensor 3; navigation 3; Cruise Control 3
Interior fan Central locking; navigation 3; door mirror memory 3
Main light switch Electrically adjustable driver’s seat

18
19
20
21

22
23
24
25

40
10
15
10

40
15
20
30

95_US_MY09.book Page 217 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

217

26

27
28
29

30

31

32
33
34
35
36
37
38
39

7,5 Driver seat memory 3; mirrors memory 3;

moonroof 3; parking assistant 3; seatbelt reminder; ACC Engine-management system; SID; main instrument

10
7.5 Airbag 7.5 ABS/ESP® 7.5 Starter motor; transmission control module (cars with

automatic transmission)

7.5 Cruise control 3; water valve; fog lights, front 3; rain

sensor 3
–

12-volt socket (cigarette lighter) front/rear Daytime running light Electric windows, left

– 7.5 Direction-indicator switch 30
15
30
30 Windshield wipers 30
20

Electric heating, front seats 3
Limp-home solenoid

B C1 C2

L1

L2

Relay panel under instrument panel

C1 C2

Function – Electric heating of rear seat – – – Main relay (engine management system) – Fuel pump Ignition switch Rear-window / door mirrors heating

95_US_MY09.book Page 218 Tuesday, April 15, 2008 11:03 AM

218

Car care and technical information

L1
L2

– Starter relay Limp-home function –

13

17

10

14

11

15

10

11

12

13

14

12

16

15

16

17

Fuse box under hood Fuses

Amp Function 40 Radiator fan, high speed 40 ABS/ESP® 30 ABS/ESP® 7.5 Load angle sensor (cars with xenon headlights) 15 Heater 10 A/C; car alarm siren 15 Bulb test – 20 Headlight washers

–

95_US_MY09.book Page 219 Tuesday, April 15, 2008 11:03 AM

10
11
12
13
14
15
16
17
18

15 High beam headlight, left 15
Low beam headlight left 15 High beam headlight, right 15
Low beam headlight, right 30 Radiator fan, high speed 15 Fog lights (front spoiler) 20 Wiper, rear 15 Horn –

–

Car care and technical information

219

Relays

10
11
12
13
14
15
16
17

Function Bulb test; head light; high beam flasher Headlight washer Front fog lights Wiper, rear (9-5 SportCombi) – – Rain sensor Radiator fan, low speed Radiator fan, high speed A/C-compressor Radiator fan, high speed, right fan Horn Extra lights (accessory) High beam headlight Low beam headlight – Windshield wipers

95_US_MY09.book Page 220 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

220
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Saab Warranty and Service Record Booklet for details.

WARNING

Poorly maintained and improperly used tires are dangerous. (cid:127) Overloading your tires can cause

overheating as a result of too much friction. You could have an blow-out and a serious accident. See “Loading Your Vehicle” on page 229.

(cid:127) Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold.

(cid:127) Overinflated tires are more likely to be cut, punctured or broken by a sudden impact – such as when you hit a pot- hole. Keep tires at the recommended pressure.

(cid:127) Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.

Adjust the tire pressure to match the current load and speed of the car (see page 263). The stated tire pressures apply to cold tires, i.e. tires that are the same temperature as the outside air temperature. Tire pressure increases as the tires become warm (e.g. during highway driving) by approximately 0.3 bar (4 psi). When the temperature of the tires changes by 50°F (10°C), the tire pres- sure will change 0.1 bar (2 psi). Never reduce the pressure of a hot tire. If the tires are hot when you check them, only increase the pressure, if necessary.

Inflation - Tire Pressure The Tire-Loading Information label shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehi- cle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Notice: Don’t let anyone tell you that underinflation or overinflation is all right. It’s not. If your tires don’t have enough air (underinflation), you can get the following: (cid:127) Too much flexing (cid:127) Too much heat (cid:127) Tire overloading (cid:127) Bad wear (cid:127) Bad handling (cid:127) Bad fuel economy

If your tires have too much air (overinfla- tion), you can get the following: (cid:127) Unusual wear (cid:127) Bad handling (cid:127) Rough ride Needless damage from road hazards

95_US_MY09.book Page 221 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

221

High speed operation

WARNING

Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require infla- tion pressure adjustment for high speed operation. When speed limits and road conditions are such that a vehicle can be driven at high speeds, make sure the tires are rated for high speed operation, in excellent condition, and set to the correct cold tire inflation pressure for the vehicle load.

Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tight- ened. See page 239.

WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. See “Changing a wheel” on page 237.

When to check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gauge to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they’re underinflated. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. Tire Inspection and Rotation Tires should be rotated every 10,000 miles (16 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It Is Time for New Tires” on page 222 and “Wheel Replacement” on page 225 for more infor- mation. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehi- cle. The first rotation is the most important. When rotating your tires, always use the correct rotation pattern. Left front tire to left rear. Left rear tire to right front. Right front to right rear. Right rear to left front.

95_US_MY09.book Page 222 Tuesday, April 15, 2008 11:03 AM

222

Car care and technical information

Flat spotting All tires get hot, especially on long journeys or when the car is driven hard. After the car has been parked with hot tires and the tires have cooled down, a flat spot can form in the tire, where it is in contact with the ground. The same can occur if the car has not been moved for a long time. Flat spots can cause vibration that can be felt through the steering wheel, similar to that experienced when the wheels need bal- ancing. Flat spots of this type disappear once the tires get hot again, usually after 10–15 miles (20–25 km) of driving at cruising speed.

When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: (cid:127) You can see the indicators at three or

more places around the tire.

(cid:127) You can see cord or fabric showing

through the tire’s rubber.

(cid:127) The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.

(cid:127) The tire has a bump, bulge or split. (cid:127) The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage.

Wear indicators

Treadwear indicators The tires incorporate wear indicators in the form of smooth, treadless strips across the width, which become visible when only 2/32" (1.6 mm) of tread remains. As soon as the indicators become visible, new tires should be fitted without delay. Make sure you are familiar with the legal limit for minimum tread depth in your country and also any regulations gov- erning the use of winter (snow) tires.

95_US_MY09.book Page 223 Tuesday, April 15, 2008 11:03 AM

Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. Before changing to wheels/tires of another size, we recommend that you contact an authorized Saab workshop regarding acceptable options. See also page 261
Wheels/tires combinations that are not approved by the vehicle manufacturer can negatively affect the car’s directional stabil- ity, steering and braking in both wet and dry conditions. The wheels and tires have been carefully matched to the characteristics of the car and play a key role in its outstanding roadhold- ing and handling. Do not take it for granted that a wheel/tire combination will work in the best possible way, just because it can be fitted to the car. To ensure that the speedometer is as accu- rate as possible it should be reprogrammed if wheels of a different dimension are fitted. Contact a Saab dealer. Because of front wheel drive, the front tires tend to wear faster than the rear ones. New tires should always be fitted in pairs, so that tires on the same axle have the same amount of tread. Store wheels lying flat or hanging – never standing upright.

Car care and technical information

223

NOTICE

Wide wheels and tires with sidewalls that are too low can: (cid:127) be damaged in potholes etc. (cid:127) cause springs, shock absorbers and wheel bearings and body mountings can be overloaded.

(cid:127) cause the wheels to come into contact

with chassis and body components.

(cid:127) can affect the function of the Elec- tronic Stability Program (ESP®).

The speed and load limits for the tires must not be exceeded; see page 228. Wheels larger than 17” must not be fitted. The maximum permissible offset is 49 mm.

WARNING

Mixing tires could cause you to lose con- trol while driving. If you mix tires of differ- ent sizes or types (radial and bias-belted tires), the vehicle may not handle prop- erly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. It’s all right to drive with your compact spare temporarily, it was developed for use on your vehicle. See “Compact spare tire” on page 235.

WARNING

If you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.

95_US_MY09.book Page 224 Tuesday, April 15, 2008 11:03 AM

224

Car care and technical information

Uniform Tire Quality Grading Quality grades can be found where applica- ble on the tire sidewall between tread shoul- der and maximum section width. For exam- ple:

Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administra- tion, which grades tires by treadwear, trac- tion and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the side- walls of most passenger car tires. The Uni- form Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-pro- duction tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Perfor- mance Criteria (TPC) standards.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the govern- ment course as a tire graded 100. The rela- tive performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service prac- tices and differences in road characteristics and climate.

Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades repre- sent the tire’s ability to stop on wet pave- ment as measured under controlled condi- tions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warn- ing: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dis- sipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temper- ature can lead to sudden tire failure. The grade C corresponds to a level of perfor- mance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

95_US_MY09.book Page 225 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

225

Used Replacement Wheels

WARNING

Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.

Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall per- formance. Scheduled wheel alignment and wheel bal- ancing are not needed. However, if you notice unusual tire wear or your vehicle pull- ing one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new Saab original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.

WARNING

Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

Notice: The wrong wheel can also cause problems with bearing life, brake cool- ing, speedometer or odometer calibra- tion, headlamp aim, bumper height, vehi- cle ground clearance and tire or tire chain clearance to the body and chassis. See “Changing a wheel” on page 237.

WARNING

When fitting just one new pair of tires, these should be fitted to the rear wheels, as these are more critical to the direc- tional stability of the car (e.g. on braking or in a skid). The existing rear wheels should therefore be moved to the front.

95_US_MY09.book Page 226 Tuesday, April 15, 2008 11:03 AM

226

Car care and technical information

Tire Chains

WARNING

If your vehicle has 225/45 R17 alt. 235/45 R17 size tires, don’t use tire chains, there’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manu- facturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it’s con- tacting your vehicle, and don’t spin your wheels. If you do find traction devices that will fit, install them on the front tires.

Notice: If your vehicle does not have 225/45R17 alt. 235/45 R17 size tires, use tire chains only where legal and only when you must. Contact your Saab dealer regarding suitable snow chains. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instruc- tions. If you can hear the chains contact- ing your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

If a Tire Goes Flat It’s unusual for a tire to “blow-out” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blow-out”, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to main- tain lane position, and then gently brake to a stop well out of the traffic lane. A rear blow-out, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the acceler- ator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop – well off the road if possible. If a tire goes flat, the next part shows how to use your jacking equipment to change a flat tire safely.

95_US_MY09.book Page 227 Tuesday, April 15, 2008 11:03 AM

Tire Sidewall Labeling Useful information about a tire is molded into it´s sidewall. Tire size: The tire size ia a combination of letters and numbers used to define a partic- ular tire´s width, height, aspect ratio, con- struction type and service description. Department of Transportation (DOT): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety standards. Tire Identification Number (TIN): The let- ters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manu- factured. The TIN is molded onto both sides of the tire. Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.

Car care and technical information

227

Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on performance factors: tread- wear, traction and temperature resistance. For more information see “Uniform Tire Quality Grading” on page 224. Maximum Cold Inflation Load Limit: Max- imum load that can be carried and the max- imum pressure needed to support that load. For information on recommended tire pres- sure see “Lowest recommended tire pres- sure, cold tires” on page 263and “Loading Your Vehicle” on page 229.

Tire Size The following illustration shows an example of a typical passenger car tire size.

215 / 55 R 16 93 H

a Tire Width b Aspect Ratio c Belt Rating d Rim diameter e Load range f Speed rating

Tire Width: The three-digit number indi- cates the tire section width in millimeters from sidewall to sidewall.

95_US_MY09.book Page 228 Tuesday, April 15, 2008 11:03 AM

228

Car care and technical information

Aspect ratio: A two-digit number that indi- cates the tire height-to-width measure- ments. For example, if the tire size aspect ratio is “55”, as shown in item “C” of the illus- tration, it would mean that the tire´s sidewall is 55% as high as it is wide. Belt Rating: A letter code is used to indicate the type of ply construction in the tire. The letter “R” means radial ply construction; the letter “D” means diagonal or bias ply con- struction; and the letter “B” means belted-bias ply construction. Rim Diameter: Diameter of the wheel in inches. Load range: The load range represents the load carry capacity a tire is certified to carry. Speed Rating: The maximum speed that a tire is certified to carry a load. Speed ratings range from “A” to “Z”.

Tire markings An example of the meaning of the different markings in a tire size is given below for a tire size of: 215/55 R16 93 V

215 Tire section width, mm

Aspect ratio, i.e. the section height is 55 % of the section width

55
R Radial ply

Wheel rim diameter 16 in at bead seats

16
93 Tire load code V Speed marking

Tire load index Tire approved for max. 1355 lbs. (615 kg)

91
93 Max. 1433 lbs (650 kg) 94 Max. 1477 lbs (670 kg)

Speed ratings Tire approved for speeds up to 100 mph (160 km/h)

S Max. 112 mph (180 km/h) T Max. 118 mph (190 km/h) H Max. 130 mph (210 km/h) V Max. 150 mph (240 km/h) W Max. 167 mph (270 km/h) Y Max. 186 mph (300 km/h)

TIN-code a Manufacturer´s Identification Mark b Tire Size c Tire Type Code d Date of Manufacture

95_US_MY09.book Page 229 Tuesday, April 15, 2008 11:03 AM

Loading Your Vehicle

This label can only be found on vehicles sold in the U.S. Vehicles sold in Canada have the tire information label in the glovebox, see page 264.

This is an example of what your vehicle´s Tire-Loading Information/Certification label might look like. It is located on the B-pillar and shows how much weight your vehicle may properly carry. The label tells you the proper size, and recommended inflation pressures for the tires on your vehicle. It also gives you important information about the number of people that can be in your vehicle and the total weight that you can carry. This weight is called the Vehicle Capacity Weight, and includes the weight of all occupants, cargo and all nonfac- tory-installed options.

Car care and technical information

229

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the com- bined weight of optional accessories, for example, automatic transmission, power steering, power brakes, power windows, power seats, radio and air conditioning. Aspect Ratio: The relationship of a tire´s height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other rein- forcing materials. Bias Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread. Cold Inflation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascal (kPa), before a tire have built up heat from driving. See “Inflation - Tire Pressure” on page 220. Curb weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, without passengers and cargo.

DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety stan- dards. The DOT code includes the Tire Identification Number (TIN), an alphanu- meric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating see page 258. GAWR FRT: Gross Axle Weight Rating for the front axle, see page 258. GAWR RR: Gross Axle Weight Rating for the rear axle, see page 258. Intended Outboard Sidewall: The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. There are 6.9 kPa to one psi. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.

95_US_MY09.book Page 230 Tuesday, April 15, 2008 11:03 AM

230

Car care and technical information

Maximum Load rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehi- cle capacity weight; and production options weight. Maximum Permissible Inflation Pres- sure: The maximum cold inflation pressure to which a tire may be inflated. Normal occupant weight: The number of occupants a vehicle is designed to seat mul- tipled by 150 pounds (68 kg). See “Loading Your Vehicle” on page 229. Occupant Distribution: Designated seat- ing positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehi- cle. The side of the tire that contains a white- wall bears white lettering or bears manufac- turer, brand and or model name molding on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles.

Recommended Inflation Pressure: Vehi- cle manufacturer´s recommended tire infla- tion pressure shown on the tire label, see “Inflation - Tire Pressure” on page 220 and “Loading Your Vehicle” on page 229. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the cen- terline of the tread. Rim: A metal support for a tire or a tire and tube assembly upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip pro- vided. Treadwear Indicators: Narrow bands, sometimes called “wear bars”, that show across the tread of a tire when only 2/32 inch of tread remains. See “When It Is Time for New Tires” on page 222.

Tread Width: The width of the tire´s tread. UTQGS: Uniform Tire Quality Grade Stan- dards, a tire information system that pro- vides consumers with ratings for a tire´s traction, temperature and treadwear. Rat- ings are determined by tire manufacturers using government testing procedures. The rating are molded into the sidewall of the tire. See “Uniform Tire Quality Grading” on page 224. Vehicle Capacity Weight: Is the number of designated seating positions multipled by 150 pounds (68 kg) plus the rated cargo load. See “Loading Your Vehicle” on page 229. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight and cargo weight. Vehicle label: A label permanently attached to a vehicle showing original equipment tire size and the recommended cold inflation pressure. See “Loading Your Vehicle” on page 229.

95_US_MY09.book Page 231 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

231

Tire date code Tires should be regarded as perishable goods. As the tires age, the rubber becomes progressively harder, and the roadholding ability of the tires diminishes. This is partic- ularly true on winter tires. Tires now have a date-code marking for the year of manufacture. The first two digits denote the week number and the two last digits the year followed by a filled triangle. Tire direction of rotation The direction of rotation is important for the majority of tires. These tires have a marking on the side of the tire. The marking may state "Tire rotation" together with an arrow or the text "Facing out". The tire must rotate in the same direction for its entire service life.

Steps for Determining Correct Load Limit 1 Locate the statement “The

combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle´s label.

2 Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3 Subtract the combined weight of the

driver and passengers from XXX kilograms or XXX pounds.

4 The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400–750 (5x150) = 650 lbs.).

5 Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calcu- lated in Step 4.

6 If your vehicle will be towing a trailer,

load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehi- cle.

Winter tires Winter (snow) tires are recommended for winter climates where the majority of your driving will be done on snow and ice. Winter tires should be fitted to all four wheels to maintain a proper balance. Your Saab dealer can advise you of to the correct size tire for your car (if different from the original size) and also supply Saab approved winter tires pre-mounted on steel or alloy rims. Winter tires normally use a different speed rating compared to summer/all season tires. Make sure not to exceed the stated speed rating on the tires you use. Make sure that wheels with sensors for tire pressure monitoring are fitted during replacement if the car has automatic tire pressure monitoring.

95_US_MY09.book Page 232 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

232
Automatic tire pressure monitoring system

WARNING

The system is an aid to the driver. The driver always has the responsibility that the tires have the correct air pressure. For optimum safety, economy and com- fort tire pressures should be checked reg- ularly even if the automatic tire pressure monitoring has not alarmed.

The system consists of a sensor in each wheel and a commopn receiver. The sen- sors are located inside the tire in direct con- nection with the air pressure valves. Make sure that wheels with sensors for tire pressure monitoring are fitted during replacement if the car has automatic tire pressure monitoring.

NOTICE

Tire replacement must take place with great care to avoid damaging the sensors that are built together with the valves. (cid:127) Remove the rear side first.

(cid:127) Start to remove the tire opposite the

valve.

(cid:127) During removal the tire machine must not come closer than ±10° from the valve.

(cid:127) During fitting, start 20° after the valve

and finish 20° before the valve.

(cid:127) Do not inflate the tire with pressure

higher than 102 psi (700 kPa).

Tire pressure information is transmitted wirelessly to the receiver. The system checks the tire pressures when speed exceeds 19 mph (30 km/h). The system is self-programming which means that the wheels can be shifted around without any need for adjustment. The spare wheel has no sensor. The sensor batteries last for 10 years or around 160 000 km. The battery cannot be replaced. The whole sensor must be replaced.

Valve with sensor

The system does not warn if the tire pres- sure is too high.

95_US_MY09.book Page 233 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

233

If the tire pressure continues to decrease then an alarm is shown on the SID when the pressure has decreased to 23 psi (159 kPa) which is the lowest permitted pressure for the tire. An alarm is also received when leakage is greater than 3 psi/min. (20 kPa/min.).

Low tire pressure front right. Make a safe stop.

Reduce speed (avoid heavy braking and significant steering wheel movement) and stop the car as soon as possible at a suita- ble location. Replace the defective wheel. The fault message can remain for up to 10 minutes after restarting the car. Then it disappears if the tire pressure is correct. Check/adjust the pressure in the other tires when a fault message is shown.

Note that the tire pressure can decrease without a puncture. The pressure could decrease around 3 psi (20 kPa) during a three month period. The outside temperature could also affect tire pressure. The specified tyre pressures are valid for cold tyres. The increased tyre pressure resulting from extensive driving must not be reduced. Tyre pressure table, see page 263. If the system has triggerd a low pressure warning or alarm then the tire pressure must be adjusted to the recommended pressure in order to put out the warning or alarm. For further information on tire air pres- sure, see page 220. Allow 10 minutes for the system to recogn- ise the wheel/sensors positions after fitting a new set of tires. During this period no low pressure warning or alarm can be triggered.

Valve without sensor

If the tire pressure decreases If the tire pressure decreases to 0.4 bar (6 psi) below the recommended pressure then a warning is shown on the SID as to which tires are affected.

Tire pressure low, rear left. Check tires.

Adjust the pressure as soon as possible.

95_US_MY09.book Page 234 Tuesday, April 15, 2008 11:03 AM

234

Car care and technical information

Malfunctions

Tire pressure system failure. Contact service.

The above message is shown on the SID if: (cid:127) a wheel without pressure sensor has

been fitted (e.g. spare wheel)

(cid:127) one or more pressure sensors are broken

or missing

(cid:127) a fault has arisen in the receiver (cid:127) a system error has arisen.

Removing a tire Remove the tire with a tire machine. It is important to follow the instructions for the tire machine as well. (cid:127) Do not fit the tire tool in an area ±10° from

the valve.

(cid:127) Start removing opposite the valve. (cid:127) Remove the rear side first.

Fitting a tire Fit the tire with a tire machine. It is important to follow the instructions for the tire machine as well. (cid:127) Start to fit about 20° after the valve. (cid:127) Finish fitting before an area 20° from the

valve.

(cid:127) Do not inflate the tire to a pressure higher

than 102 psi (700 kPa).

95_US_MY09.book Page 235 Tuesday, April 15, 2008 11:03 AM

Compact spare tire

WARNING

Stow all tools carefully away after use, so that they cannot get loose and cause injury in the event of a crash.

The spare tire, together with the jack, front towrope attachment eye and toolkit, is stowed away underneath the luggage-com- partment floor. The compact spare is light and easy to handle when changing the tire. Its use is only permitted when a standard tire has sus- tained a puncture. The maximum life of the tire is only 2000 miles (3,500 km).

Car care and technical information

235

NOTICE

To avoid damaging a punctured alloy wheel it can be placed outside up in the spare-wheel well but only while driving to the closest dealer. A general rule is that all heavy loads must be well secured in the luggage compart- ment, see page 131 and 135.

Spare wheel (under panel in luggage compartment)

Do not exceed 50 mph (80 km/h) with the compact spare fitted. The compact spare should be inflated to 60 psi (420 kPa). Carry the punctured tire in the spare-wheel well under the luggage- compartment floor. Have the standard tire repaired and refitted as soon as possible.

95_US_MY09.book Page 236 Tuesday, April 15, 2008 11:03 AM

236

Car care and technical information

Driving considerations with compact spare wheel/tire fitted

WARNING

(cid:127) Do not exceed 50 mph (80 km/h) as the tire can overheat and adversely affect the handling of the car.

(cid:127) Tire pressure: refer to page 263. (cid:127) The spare wheel or punctured tire

must be stowed under the trunk floor, and secured in place with the retaining nut.

The following should be observed when the compact spare wheel (T115/70 R16) is fitted: (cid:127) The compact spare is light and easy to

handle when changing the wheel.

(cid:127) Do not drive further than necessary with the compact spare fitted – the maximum life of the wheel is only just over 2000 miles (3,500 km).

(cid:127) Refit the standard tire as soon as possi-

ble.

(cid:127) Fitting a spare tire/wheel without pressure

sensor will trigger a malfunction message, see page 234.

Hanging up the cover, 9-5 SportCombi

Important considerations when driving with a compact spare tire: (cid:127) The car’s ground clearance is reduced. (cid:127) The car must not be driven with more than

one compact tire at a time. (cid:127) Avoid driving against a curb. (cid:127) Do not use snow chains. (cid:127) Do not fit the wheel cover - this would

conceal the warning text.

95_US_MY09.book Page 237 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

237

(cid:127) The jack should be stored correctly under the carpeting in the trunk. If it lies loose in the car, it could thrown for- ward and cause personal injury in the event of a crash or if the car rolls over.

(cid:127) Grit, salt and rust can clog the inner

threads of the wheel bolts if the car has been driven for several years exclu- sively with alloy wheels. If steel wheels are being installed, the bolt hole threads in the brake hubs should be cleaned before the thinner steel wheels are fitted. It may other- wise not be possible to achieve the correct clamping force, despite tight- ening the wheel bolts to the correct torque.

Changing a wheel

WARNING

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for chang- ing a flat tire.

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:

1 Set the parking brake firmly. 2 If you have an automatic transmis-

sion, put the shift lever in PARK (P). For a manual transmission, leave the car in gear (1st or REVERSE (R)).

To be even more certain the vehicle won't move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle.

(cid:127) The car jack is designed solely for use

in changing a wheel or fitting snow chains. It must not be used to sup- port the car during repair work or servicing.

(cid:127) Never crawl under a car that is

supported only by a jack.

(cid:127) Raising your vehicle too high or with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle, and raise the vehicle only far enough off the ground so there is enough room for the spare tire to fit (no more than 25 mm or 1 inch clearance between the ground and the bottom of the tire).

3 Turn off the engine and do not restart

while the vehicle is raised.

(cid:127) Switch on the hazard warning lights if

the car is on a road.

4 Do not allow passengers to remain in

the vehicle.

95_US_MY09.book Page 238 Tuesday, April 15, 2008 11:03 AM

238

Car care and technical information

Jacking points for a floor jack

Position for jack

To jack up the car, apply the jack to one of the special jacking points under the sills. If a floor jack is used, it can be applied to the standard jacking points used by the dealer. A floor jack can lift both front wheels or both rear wheels off the ground simultaneously. A jack stand must then be applied under- neath the front of the engine subframe (at the fixing point for the towrope-attachment eye) or to the rear towrope-attachment eye (or under the trailer hitch, if fitted).

NOTICE

Apply the jack only to the jacking points indicated on the body.

1 Put the car in 1st gear (automatic trans- mission: move selector to the P position) and apply the parking brake.

2 Wind the jack up to a suitable height

before placing it under the recess in the sill. Make sure that the jack fully engages the recess in the sill and that the base of the jack is steady and flat on the ground.

3 Remove the wheel cover (where appli-

cable). Remove the wheel bolt caps and loosen the wheel bolts by half a turn.

4 Wind the jack to raise the wheel clear of the ground. Remove the wheel bolts and lift off the wheel.

95_US_MY09.book Page 239 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

239

Removing the plastic wheel bolt caps

5 Clean any rust or dirt from the contact surfaces between the wheel and brake disc. Do not wipe away the grease in the hub.

6 Fit the wheel and screw in the bolts in the sequence shown (opposite pairs) - see page 240. Tighten the bolts enough for the bolts and wheel to be seated correctly.

Clean any rust or dirt from the contact sur- faces between the wheel and brake disc

7 Lower the car and tighten the wheel

bolts to the correct torque in the sequence shown (opposite pairs).Replace the wheel bolt caps. Tightening torque Light-alloy wheels: 80 ft.lbs. (110 Nm) Steel wheels: 80 ft.lbs. (110 Nm). Lubricate the wheel stud head with a small amount of petroleum jelly or simi- lar and reinstall the plastic covers on the wheel studs. The petroleum jelly facilita- tes removal.

Do not wipe away the grease in the hub.

NOTICE

(cid:127) When refitting wheel covers (where

applicable), make sure that the valve protrudes through the marked hole in the wheel cover.

(cid:127) Do not overtighten the bolts using an

impact wrench: not only can this damage the wheels but it can also make it impossible to undo the bolts using the wheel wrench in the car’s toolkit.

95_US_MY09.book Page 240 Tuesday, April 15, 2008 11:03 AM

240

Car care and technical information

8 Check-tighten the wheel bolts after a few

miles. Tightening torque Light-alloy wheels: 80 ft.lbs. (110 Nm) Steel wheels: 80 ft.lbs. (110 Nm)

Tightening sequence, wheel bolts

Removing the wheel cover

Safety belts

WARNING

If the car is involved in a crash, the safety belts, belt pretensioners and other com- ponents must be inspected by a work- shop. We recommend that you contact an authorized Saab dealer. Never make any alterations or repairs to the safety belt yourself.

Regularly check the function of the safety belts as follows: (cid:127) Hold the diagonal strap and pull it sharply. The safety belt should lock and it should not be possible to withdraw it further.

Check the anchorage points in the floor. They must not have suffered rust damage. There must be no frayed threads in the web- bing. Safety belts must not come into contact with substances such as polishes, oils or other chemicals. If the straps are dirty, wash them with warm water and a detergent or have them replaced.

95_US_MY09.book Page 241 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

241

Textile carpeting Vacuum clean the carpeting regularly. Car- pets can also be cleaned using a brush, or carpet shampoo applied with a sponge. Do not use vacuum cleaners outdoors unless they are properly grounded.

Upholstery and trim To remove lint or hairs from the seat uphol- stery or headlining, use a moist, lint-free cloth or a special lint remover (brush or roller). Remove any dirty marks using a cloth moistened with lukewarm soapy water. When using a stain remover, always work from the outside towards the center to avoid leaving a ring. If a soiled ring or spot should remain, it can usually be removed using lukewarm soapy water or water alone. Wet patches left by spilled soft drinks or thin oil must be wiped off immediately using an absorbent material, such as a paper towel, and treated with stain remover. Alcohol is recommended for removing grease or oil stains, and a semi-stiff brush may also be used.

Cleaning and caring for leather upholstery The principal reason for treating leather upholstery is to maintain its elegant appear- ance and to provide it with a protective film. Discoloration caused by dust and wear mainly affects the lighter shades, although this is not detrimental to the leather – indeed, the patina resulting from use is often considered desirable in leather. But if the leather is allowed to become too grubby, it can start to look shabby. Regularly vacuum the leather with a soft brush to remove loose dirt and dust. It is a good idea to clean and recondition the leather twice a year – in conjunction with a general spring-cleaning of the car – after the winter and in the autumn, for instance. In hot, dry climates, the leather will need to be treated more frequently. Use conventional leather care products. Follow the instruc- tions on the packaging. Do not use harsh polishing agents, cleaning agents, sprays, coarse soap or hot water. Semi-aniline leather only has a thin protec- tive finish and is therefore more sensitive than other leathers and therefore need more care to keep the protection and ageing properties.

95_US_MY09.book Page 242 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

242
Washing the car Wash your car frequently. To facilitate cleaning, a suitable detergent can be added to the water, which should be lukewarm. Saab offers a full line of car care products, including car wash, for the care of your vehi- cle. See your dealer for available products or visit www.saabcatalog.com (U.S. resi- dents only). Do not use a pressure washer at close range on stone chip damage, scratches or other damage to the paintwork. The paint can otherwise start to flake. Remove any bird droppings without delay, as these can discolor the paintwork and prove difficult to polish out. Use a soft cloth moistened with methyl alco- hol to remove splashes of tar or asphalt. Do not use strong cleaners, as these can dry out the paintwork.

NOTICE

Only use liquid detergent when cleaning the plastic lenses of the front and rear lights. Do not use mechanical cleaning. Rinse off the detergent immediately, oth- erwise cracks may form in the plastic lenses.

The underside of the car also needs wash- ing regularly, and this should be done extra thoroughly at the end of winter. Clean the underside of the car by hand if the car is usually washed in an automatic car wash without special facilities for underbody cleaning. Never wash or leave the car to dry in the sun, but wipe it dry with a chamois leather immediately after washing to avoid smears and streaks. Clean the window glass inside and out using a high quality window cleaner. This is partic- ularly important when the car is new, as upholstery and trim have a tendency to sweat a little at first. Keep the glass well cleaned, as this helps to prevent misting.

NOTICE

(cid:127) The door mirrors must be fully

retracted before the car enters an automatic car wash.

(cid:127) Remove fixed antennas, e.g. for mobile phone, before putting car through an automatic car wash.

(cid:127) Try your brakes on leaving a car wash. Wet brake discs may reduce the per- formance of the brakes.

(cid:127) Cars with Saab Parking Assistance: Do not spray the sensors or closer than 8 in. (20 cm) to the sensors with a pressure washer, as this can damage them.

95_US_MY09.book Page 243 Tuesday, April 15, 2008 11:03 AM

Car care and technical information