Download PDF Manual


The lamp illuminates if the tire pressure in one or more tires is too low or if a fault has arisen in the system, see page 232. Below is an example of the message simul- taneously shown on the SID:


Low tire pressure front left. Make a safe stop.


95_US_MY09.book Page 64 Tuesday, April 15, 2008 11:03 AM


64


Instruments and controls


1 Cars with automatic transmission


Autochecking of lights, main instrument panel The above warning and indicator lights should come on when the ignition is switched on prior to starting. They should go out after about 3 seconds. The following lights light up until the engine is started, presuming that no fault exists:


(cid:127) Oil pressure warning light


(cid:127) Warning, charging


Instruments Tachometer The tachometer indicates the engine speed in thousands of revolutions per minute. The needle may be allowed to enter the broken red zone on the dial only for an instant. A safety cut-out function (in the fuel system) prevents the engine speed from exceeding approximately 6,000 rpm.


Odometer and trip meter The odometer records the distance traveled in miles on U.S. vehicles and on Canadian vehicles the distance indicated is in kilome- tres, and the trip meter in miles and tenths (kilometres and tenths of kilometres on Canadian vehicles). Reset button The reset button has two functions, deter- mined by whether the ignition is ON or OFF. (cid:127) When the ignition is ON, pressing the


button will reset the trip meter.


(cid:127) When the ignition is OFF, the display


lights up enabling you to read the odome- ter and trip meter. Pressing the button a second time will reset the trip meter.


Fuel gauge Fuel-tank capacity, 18.5 US gal. (70 liters). The fuel gauge shows the amount of fuel left in the tank. When this is down to about 2.5 gal. (10 liters), a warning light on the main instrument panel will come on (see page 61). Because of the fuel remaining in the tank, the amount of fuel required to fill the tank may be less than the specified tank capac- ity. Use the Saab Information display (SID) to check the approximate distance that can be traveled on the remaining fuel (see page 68).


Instruments and controls


65


95_US_MY09.book Page 65 Tuesday, April 15, 2008 11:03 AM


Speedometer (U.S. speedometer shown) The speedometer receives signals from the wheel sensors in the ABS system. Cars sold in U.S.: The speedometer dis- plays the speed of the car in miles per hour (mph). Cars sold in Canada: The speedometer dis- plays the speed of the car in kilometres per hour (km/h).


95_US_MY09.book Page 66 Tuesday, April 15, 2008 11:03 AM


66


Instruments and controls


Temperature gauge The temperature gauge shows the temper- ature of the coolant. The needle should be in the middle of the scale when the engine is at normal operating temperature. If the needle approaches the red zone, which can occur in very hot weather or when the engine is under a heavy load, drive in the highest gear possible, keep the engine revs low and avoid shifting down.


NOTICE


If the needle, despite the above action, enters the red zone, stop the car immedi- ately, let the engine idle. If the needle stays in the red zone, stop the engine.


Check fuse 1 (radiator fan) in the fuse panel under the hood, see page 218. If the needle repeatedly enters the red zone, stop the car as soon as it is safe to do so and check the coolant level by looking at the level visible through the plastic tank – do not remove the cap.


If the coolant level falls below the MIN mark, the Saab Information Display (SID) will display the message ”Coolant level low. Refill.”.


WARNING


Never open the cap of the expansion tank completely when the engine is hot, open with care. The pressure in the cool- ing-system can cause hot coolant and steam to be released. Failure to heed this warning may result in personal injury.


95_US_MY09.book Page 67 Tuesday, April 15, 2008 11:03 AM


Pressure gauge The turbo gauge indicates the air volume for combustion, which is equivalent to the engine load. Under certain barometric conditions, the needle may enter the first part of the red zone without necessarily indicating that a fault has arisen. If the needle repeatedly enters the red zone and the engine at the same time loses power because the monitoring system is limiting boost pressure, you should contact a workshop immediately. We recommend that you contact an authorized Saab work- shop.


Instruments and controls


67


When the speed of the car exceeds 130 mph (210 km/h) acceleration is limited by a reduction in boost pressure. The turbo gauge will move to the middle field, indicat- ing a drop in engine output and conse- quently a reduction in vehicle speed.


Selector lever indication 3
The display below the speedometer indi- cates the position of the selector lever. If manual mode is selected, the current gear is displayed. When the sport function is selected, SPORT is displayed.


95_US_MY09.book Page 68 Tuesday, April 15, 2008 11:03 AM


Instruments and controls


68
Saab Information Display (SID)


WARNING


It is strongly recommended that the SID settings be changed only when the car is stationary. The driver’s attention can oth- erwise easily be distracted from the road.


Fuel Ø


Dist.


SID provides the following function: Temp. D.T.E.


Outside temperature Estimated range (distance to empty fuel tank) Average fuel consumption since function last reset Distance to destination/Trip meter


The Saab Information Display (SID) shows CHECK messages and incorporates eight trip-computer functions. Use the i/SET button to browse the func- tions.


Speed Ø Average speed since function


last reset Alarm Alarm function Speed W. Speed warning


SID, buttons and display


Outdoor temperature (Frost warning) Regardless of which function has been selected, except Night Panel Mode, SID will automatically display the outdoor tempera- ture when it is between 26° and 38°F (–3° and +3°C). This also applies if the temperature has moved outside the range of 21° to 43°F (–6° to +6°C) but is again between 26° and 38°F (–3° and +3°C).


WARNING


Remember that roads can be icy even at temperatures of above 38°F (+3°C), especially on bridges and stretches of road that are sheltered from the sun.


Alarm 1 Select Alarm with the i/SET button. 2 Hold i/SET depressed until a chime


sounds. Briefly press the i/SET button if you do not wish to change the alarm time. If you wish to change the alarm time, press End with a brief press on the i/SET button.


or


ON appears to the right of the alarm time to indicate that the alarm will go off at the set time. When the alarm sounds, it can be deacti- vated with CLR.


Instruments and controls


69


Activating speed warning 1 Select Speed W. with the i/SET button. 2 Hold i/SET depressed until a chime


sounds. Briefly press the i/SET button if you do not wish to change speed. If you wish to change speed, press


or


End with a brief press on the i/SET button.


ON appears to the right of the speed if a warning will sound when vehicle speed exceeds the set speed.


Disengaging speed warning 1 Select Speed W. with the i/SETbutton. 2 Briefly press the CLR button.


95_US_MY09.book Page 69 Tuesday, April 15, 2008 11:03 AM


Entering values for the functions Dist. 1 Select Dist. using the i/SET button. 2 Hold i/SET depressed until a chime sounds and the selected function is marked.


3 Set the distance using 4 End with a brief press on the i/SET


or


button. The calculated arrival time will then appear next to the distance.


SID calculates arrival time using the set dis- tance and average vehicle speed. The values are updated during the trip. If you take a break, this time is added to the previously calculated arrival time. After the distance to destination has decreased to zero, Dist. will function as a trip meter (see "Using Dist. as a trip meter"). The starting value for the trip meter will be the last distance set for the Dist. function. Example: 100 miles is set for the Dist. func- tion. Once the countdown has reached 0 mile, the Dist. function will act as a trip meter, beginning at 100 miles.


95_US_MY09.book Page 70 Tuesday, April 15, 2008 11:03 AM


70


Instruments and controls


Using Dist. as a trip meter If no value is programmed in Dist., it func- tions as a trip meter. This is indicated by an arrow to the right in the display. Reset the trip meter by briefly pressing the CLR button.


Calculating the arrival time if a specified average speed is maintained: 1 Select Dist. 2 Set the distance. 3 Select Speed Ø. 4 Set the average speed you intend to


drive at.


5 SID switches to Dist. automatically. The calculated arrival time is now displayed to the right.


The Speed Ø function will show actual values once you start driving.


Average fuel consumption, Fuel Ø The average fuel consumption is calculated using the values for fuel consumed and dis- tance driven since last reset. This value is stored in the car’s trip computer even when the engine is switched off. To reset the value, hold CLR depressed until a chime sounds. The text Cleared is displayed.


Resetting values To reset the value, hold CLR depressed until a chime sounds. The text Cleared is displayed. The following functions will be reset simulta- neously: (cid:127) D.T.E. (the value is reset to the distance that can be reached with the amount of remaining fuel)


(cid:127) Fuel Ø (cid:127) Speed Ø (average speed) Values programmed in Dist., Alarm and Speed W. are not reset. See respective function


95_US_MY09.book Page 71 Tuesday, April 15, 2008 11:03 AM


CHECK messages When the engine is started, CHECKING will appear on the display for about 4 seconds while the SID CHECK functions are being performed. When a CHECK message is activated while driving, a chime sounds and the message appears in SID. The number of possible CHECK messages varies depending on the car’s specifications. If more than one CHECK message has been generated, the + symbol will appear to the left of the text on the display. The mes- sages appear in order of priority. If a new fault occurs whilst another message is being displayed, the message relating to the new one will appear for 10 seconds, after which the display will return to the ear- lier one. Briefly press the CLR button to acknowl- edge a message from the display. After acknowledgement, the message is dis- played each time the ignition is re-started until remedied.


Instruments and controls


71


Low tire pressure front left. Make a safe stop. Low tire pressure front right. Make a safe stop. Low tire pressure, rear left. Make a safe stop. Low tire pressure, rear. right. Make a safe stop. Tire pressure system failure. Contact service. Time for service. 1)


232


232


232


232


232


252


1) This message will be displayed approximately 600 miles (1,000 km) before the next scheduled service is due, or when 365 days have elapsed since the last service. The message should be cleared at the time of that service (see the Saab Warranties & Service Record Booklet). This message can also be deleted by pressing the CLR button for at least eight seconds until a chime sounds. The message can only be deleted when it is shown on the SID. *) 9-5 SportCombi: the high-mounted stop light is not included in the autocheck of lights.


The following messages may be displayed:


Message Use your seatbelts. Front light failure. Rear light failure. Fog light failure. Brake light failure.*) Washer fluid level low. Refill. Coolant level low. Refill. Remote control battery low. Replace battery. Key not accepted. Contact service. Theft protection failure. Contact service. Gearbox too hot. Make a safe stop. Tire pressure low, front left. Check tires. Tire pressure low, front right. Check tires. Tire pressure low, rear left. Check tires. Tire pressure low, rear right. Check tires.


See page 12
202
206
203
206


201


193


49


54


54


154


232


232


232


232


95_US_MY09.book Page 72 Tuesday, April 15, 2008 11:03 AM


72


Instruments and controls


NIGHT PANEL To improve night-driving conditions inside the car, the Night Panel mode can be selected. In this mode, the amount of infor- mation displayed is reduced, and only the most important instruments and displays will be illuminated. When the NIGHT PANEL button is pressed, only the speedometer will be illuminated, all the other instruments illumination being extinguished and their needles moved to zero. The SID display will be extinguished and the backlighting for switches and other controls will be dimmed. Note: All indicator and warning lights, together with the display of CHECK messages, will operate as nor- mal, except ”Outdoor temperature”, see page 68.


The following conditions will wake up the respective displays in the Night-Panel mode: (cid:127) Setting of the Audio system or, SID (display comes on for ten seconds).


(cid:127) CHECK message generated in the SID. (cid:127) High engine revs cause the rev counter to be illuminated until the engine speed has fallen again. If the quantity of fuel remaining falls below 4 gallons (15 liters), the fuel gauge will be illuminated. If the engine temperature rises above normal, the temperature gauge will be illu- minated. In cars with automatic transmission, if the selector lever is moved from D to position M or L, the selector indication on the main instrument panel will be illuminated.


To restore the displays and lighting to the normal mode, press the NIGHT PANEL but- ton.


Units and language versions The SID has four sets of units:


IMPERIAL


METRIC US km km/h liters °C 24-hour 12-hour 12-hour 12-hour


GB miles miles mph mph gallon gallon °C °F


miles mph US gal °F


CHECK messages can be displayed in six language options: English, Swedish, German, French, Italian and Spanish. Selecting units and language 1 Switch off the engine. 2 Briefly press i/SETbutton. Repeat this until LANGUAGE/UNITS is displayed.


3 Hold i/SET depressed until a chime sounds. Then select language using or


4 Briefly press the i/SET button. Then


select the units using


or


5 Briefly press the i/SET button.


(cid:127) (cid:127) (cid:127) 95_US_MY09.book Page 73 Tuesday, April 15, 2008 11:03 AM


Switches


Daytime running lights The parking lights and daytime running lights come on automatically when the igni- tion switch is ON. Note to owners in the U.S.: If you do not want Daytime Running Lights, this feature can be disconnected: switch off the engine and remove fuse No. 35 (see page 216). Note to owners in Canada: Daytime Run- ning Lights must not be disconnected as they are a Canadian Federal legal require- ment.


Parking lights


The parking lights can be switched on regardless of the position of the ignition switch. Do not use parking lights when driv- ing. If the parking lights are on and the driver´s door is opened, a reminder to turn them off will sound. Note: The lighting switch must be in parking light or headlight position (low beam posi- tion only) to operate the fog lights (see page 76).


Instruments and controls


73


Light switches


1 High beam signal 2 High/low beam switching


Headlights


The headlights come on automatically when the ignition is ON and go off when the igni- tion switch is turned to the LOCK position. The parking lights, however, can be on when the ignition switch is in the LOCK posi- tion.


In cold and damp weather, the inside of the headlamp lens may temporarily mist up. This misting does not affect the func- tion or service life of the light fitting. When the lamps are on, the mist will eventually disappear.


High/low beam To switch between high and low beam, pull the control stalk fully towards you (position 2). When the high beam is on, the indicator on the main instrument panel will be illuminated. High beam flasher The headlights come on to high beam when the stalk is pulled to the first spring-loaded position (position 1) and remain on until the stalk is released.


WARNING


In poor visibility, avoid following the tail lights of the vehicle in front of you. If the vehicle stops suddenly, you may be unable to avoid a crash and therefore risk injury to yourself and others.


95_US_MY09.book Page 74 Tuesday, April 15, 2008 11:03 AM


74


Instruments and controls


Courtesy Headlight Feature A delay function allows the headlights to remain on low beam for about 30 seconds after the driver’s door has been closed. To activate this function, (cid:127) Switch off the ignition and remove the key (cid:127) Open the driver’s door (cid:127) Pull the high/low beam control stalk


towards the steering wheel like you are flashing the high beam, see page 73. The low beam headlights will now come on immediately after the driver’s door has been closed (within 30 seconds) and will remain on for about 30 seconds.


The length of time for this function can be adjusted by your authorized Saab dealer.


Rear fog light


Rear fog light Press the button to switch on the rear fog light, which will only come on if the head- lights are on. The rear fog light will go off automatically when the engine is switched off. When the fog light is next needed, it will have to be switched on manually again. The rear fog light consists of one light so it is not be mistaken for brake lights. Make sure you are familiar with the appli- cable provincial/state law regarding the use of rear fog lights.


95_US_MY09.book Page 75 Tuesday, April 15, 2008 11:03 AM


Turn signal and lane change indicators To switch on the turn signals/lane change indicators, move the stalk up or down. The stalk has fixed positions for indicating a right or left turn, and the indicators are can- celled automatically (stalk returns to off position). The stalk also has an intermediate, spring-loaded position that is useful for sig- nalling when changing lanes or passing. The respective indicator lights on the instru- ment panel flash at the same frequency as the direction indicators.


Instruments and controls


75


Turn signal and lane change indicators 1 Right indicators 2 Left indicators


Instrument illumination


Instrument illumination The brightness of the instrument illumina- tion can be varied by means of the dimmer switch adjacent to the headlight switch. (See also Night panel on page 72). In daylight or other equally bright light, the instrument and switch illumination is auto- matically extinguished.


95_US_MY09.book Page 76 Tuesday, April 15, 2008 11:03 AM


76


Instruments and controls


Front fog lights 3
The front fog lights can be activated in both low beam headlight and parking light posi- tions. Fog lights should only be used in poor visibility conditions. Make sure you are familiar with the appli- cable provincial/state law regarding the use of fog lights.


Hazard warning lights


Hazard warning lights When this button is pressed, all the turn signal indicators and a symbol in the button flash simultaneously. If the ignition is on, both indicator lights on the instrument panel will also flash. If the hazard warning lights are left on for some time, the flasher frequency will be reduced to save the battery. Hazard warning lights should only be used if the car constitutes a hazard to other road users.


WARNING


Switch on the hazard flashers if the car has to be left at the roadside on account of a crash, engine trouble or a puncture. If you carry a warning triangle or flares, they should be set up along the side of the road 300 ft. (100 m) behind your vehicle. If the car is not clearly visible (e.g. over the brow of a hill or bridge), place the tri- angle/flare even further back.


Reversing lights The reversing lights come on automatically when reverse gear is engaged or selected with the ignition switched on.


95_US_MY09.book Page 77 Tuesday, April 15, 2008 11:03 AM


Wipers and washers There are three intermittent wiper positions. Moving the control stalk to the spring-loaded position between 0 and 2 will produce a single sweep of the wipers. The wipers are designed for optimal clean- ing at all driving speeds. At higher speeds, it may be possible to detect a slight ”sweep- ing” sound. This may be due to the increased air pressure on the blades at higher speeds. Headlight washers 3
If low beam is on, the headlights are washed every fifth time the windshield washers are used or if 2 minutes have elapsed since the windshield was last washed. The headlight washers cannot be activated separately. The headlight washers are of the high-pres- sure type, which means that other parts of the car may become wet if you activate the washers while the car is stationary.


Instruments and controls


77


04


0 OFF 1 Intermittent operation 2 Low speed 3 High speed 4 Washers


Control for setting wiper delay 1 Long delay 2 Short delay


Rain sensing wipers 3


WARNING


Turn the rain sensor off if the ignition is ON when clearing snow and ice from the windshield, to avoid personal injury.


NOTICE


To avoid damaging the windshield wip- ers, turn the rain sensor off before wash- ing the car in an automatic carwash.


The rain sensor automatically controls the windshield wipers. The sensor is located on the windshield beside the rearview mirror. The system varies between single sweeps of the windshield and continuous wiping depending on how much water or snow there is on the windshield. Activate the system by lifting the control stalk to position 1. The wipers make one sweep for reference to see how much water and snow is on the windshield. In future, the sensor compares the amount of water and snow on the windshield with this reference value.


95_US_MY09.book Page 78 Tuesday, April 15, 2008 11:03 AM


78


Instruments and controls


When the engine has been switched off, the control stalk must be moved to posi- tion 0 and back to position 1 to reactivate the sensor. Set the sensitivity using the control on the wiper stalk (the same control as used for wiper delay on cars not fitted with a rain sen- sor). The sensor has three sensitivity set- tings. It is most sensitive when in the upper- most position (1). When a higher degree of sensitivity is selected, the wipers make one sweep of the windshield for reference. The rain sensor has a daylight and a night time mode. The sensor measures the amount of available light and automatically selects the appropriate mode. The sensor is more sensitive at night. The function of the rain sensor is impaired by dry snow.


Rear-window wiper 1 Intermittent wiping 2 Washers


Rear-window wiper (SportCombi) 3
The rear-window wiper and washer are operated with the same stalk switch as used for washing and wiping the windshield and headlights. This stalk has two additional switches, ON/OFF and The ON position provides intermittent wip- ing.


position provides washing and


The wiping. After a few sweeps the wiper stops or reverts to intermittent wiping, if this has been chosen. About 15 seconds after com- pletion of the washing/wiping of the rear window, the wiper makes a single sweep to wipe away any remaining washer fluid. A spring-loaded position between the OFF and ON positions allows for a single sweep of the rear-window wiper. Intermittent wiping of the rear window occurs when reverse gear is engaged if the windshield wipers are in position 1, 2 or 3, see page 77.


95_US_MY09.book Page 79 Tuesday, April 15, 2008 11:03 AM


Automatic climate control (ACC) The ACC system automatically works to maintain the desired temperature inside the car. The system will achieve the desired temper- ature in the quickest possible way. Note that selecting a higher or lower temperature than that desired will not speed up the process. For the ACC system to be most effective, all windows (and moonroof 3) should be closed. Fresh air for the cabin is drawn in through an inlet grille adjacent to the bottom edge of the windshield. The air flows through a filter upstream of the ACC system before deliv- ery to the cabin. Cabin air is evacuated via openings in the rear parcel shelf and then through outlets on either side of the car behind the rear bumper.


Instruments and controls


79


10


ACC panel 1 Temperature setting: LH side 2 AUTO: All settings selected automatically 3 Manual setting of fan speed 4 Manual setting of air distribution 5 Temperature setting: RH side


The incoming air is treated in three stages: first it passes through a filter; it is then dehu- midified and cooled and, finally, if required, heated. The filter is a combined particle and char- coal filter. It is so efficient that levels of nox- ious substances such as benzene and tolu- ene are also reduced.


6 Recirculation: ON/OFF 7 Rear-window heating: ON/OFF 8 A/C compressor: ON/OFF 9 Ventilated front seats 3
10 Heated front seats 3


To reduce the likelihood of misting on the insides of the windows, the glass should be cleaned with a quality window cleaner. How often this will need to be done depends on how clean the air is – if there are smokers in the car, cleaning will need to be done more frequently.


95_US_MY09.book Page 80 Tuesday, April 15, 2008 11:03 AM


80


Instruments and controls


The system has five sensors: (cid:127) Outdoor temperature sensor Interior temperature sensor


(cid:127) Sun sensor (mounted on top of the fascia) (cid:127) Two blended-air temperature sensors (mounted inside the front floor vents)


Note: If anything is placed over the sun sen- sor, the ACC system will not function prop- erly.


1 Interior-temperature sensor 2 Sun sensor


Panel vent


Panel vents The panel vents swivel in all directions so that air can be directed as desired. In winter, for instance, the outer vents can be directed onto the door windows for enhanced demisting. The flow of air through the panel vents can be controlled individually for each vent by means of the adjacent control. The climate control system works best if the panel vents are open. If you find the air cold or that it is drafty, start by directing the air away from the body. If the center vent is aimed up, it will cool the interior temperature sensor and you may need to adjust ACC up or down, depending upon temperature desired.


(cid:127) 95_US_MY09.book Page 81 Tuesday, April 15, 2008 11:03 AM


Air vent at rear side window


Temperature control The cabin is divided into two temperature zones: (cid:127) The driver’s zone (cid:127) The passenger zone (front and rear


seats)


The desired temperature can be set between 60 and 80°F. The displayed temperature is not the abso- lute temperature but corresponds to the comfort level normally experienced at that temperature after allowance has been made for the air flow, relative humidity, solar radiation, etc., currently prevailing inside the car. (cid:127) The most usual temperature setting is


64–76°F, depending on personal prefer- ence and what clothing is worn.


(cid:127) To allow the system time to adjust,


changes in the temperature setting shall only be made in steps of 2°F.


Once the desired climate has been achieved, the rear center vents can be closed to prevent warm air being distributed at face height. When the ignition is switched off, only the temperature control affects the system the next time the engine is started. The system will warm up/cool down to the temperature to which the control is set.


Instruments and controls


81


MAX heat, red indication The MAX heat setting is obtained by turning the temperature control to the first position past 80 (to the red LED). The driver’s side selection regulates air distribution and recir- culation status. Temperature, however, can be adjusted on the passenger side. Settings when MAX heat is selected: (cid:127) Maximum heat (cid:127) Air distribution to windshield and floor (cid:127) Recirculation OFF (even if manually


selected before) (cid:127) Fan: high speed


MAX cooling, blue indicator The MAX cooling setting is obtained by turn- ing the temperature control to the first posi- tion past 60 (to the blue LED). The driver’s side selection regulates air distribution and recirculation status. Temperature, however, can be adjusted on the passenger side. Settings when MAX cooling is selected: (cid:127) Maximum cooling (A/C compressor will run even if AC OFF manually selected before)


(cid:127) Air distribution through panel vents (cid:127) Fan: maximum speed (cid:127) Recirculation ON


95_US_MY09.book Page 82 Tuesday, April 15, 2008 11:03 AM


82


Instruments and controls


Functions Pressing AUTO will cancel all manual settings. If a manual function is selected, it will be locked in but other functions will be controlled automatically. The selected temperature is always maintained automatically.


Temperature, air distribution, fan speed and recircu- lation will be controlled automatically. Pressing AUTO once will cancel all previous manual selections. The ACC system is in AUTO mode when the engine is started. A/C compressor OFF. No cooling of inlet air. Temperature, air distribution and fan speed still under automatic control.


Turn the fan control anticlockwise until "OFF" lights up. ACC system OFF. Fan OFF. A/C compressor OFF. Air distribution selections locked in current settings. Recirculation can be selected manually. Heating 3 and ventilation 3 of the front seats is deac- tivated. Pressing the AUTO button will put the system into automatic mode. Reactivation by turning the fan control clockwise one click causes the system to resume any manual selec- tions.


The rear window and door mirror heating is controlled manually. Deactivate the heating as soon as the rear window is clear of ice and misting to avoid imposing a heavy load on the battery longer than necessary. Note, however, that heating will deactivate automatically after a set time, depending on the outside temperature. The ACC system can be programmed to activate heating automatically when outside temperature is below +5 °C and the temperature inside the car is below +10 °C. See page 85. Turn the fan control to increase fan speed. If fan speed 0 is selected, the A/C compressor will be disengaged and the indicator on the AC OFF button will illuminate.


Recirculation is controlled automatically to optimize cooling although it can also be switched on and off manually. Recirculation does not appreciably change the air quality but it can be useful to switch it on to avoid unpleasant smells from entering the cabin.


95_US_MY09.book Page 83 Tuesday, April 15, 2008 11:03 AM


Air distribution


Instruments and controls


83


One press: When the defroster is chosen manu- ally, all the windows (except the rear side windows, where the air flow is off) are demisted by: (cid:127) Fan: high speed. (cid:127) The air is directed to the defroster vents. (cid:127) Temperature increases somewhat. (cid:127) Recirculation OFF. (cid:127) Activation of rear window/door mirror heating.


The defroster function remains active until another selection is made. Note, however, that rear win- dow/door mirror heating will deactivate automati- cally after a set time, depending on the outside temperature. Two presses: Air is directed to the windscreen without the fan speed being increase or the rear window heating being switched on. To revert to a previous setting, press the AUTO button.


Defroster and floor vents


Floor vents and rear side windows


Floor and panel vents


95_US_MY09.book Page 84 Tuesday, April 15, 2008 11:03 AM


84


Instruments and controls


Panel (and center rear vent)


Starting in cold weather To start with, the system will automatically select the defroster set- ting, maximum heat and low fan speed. As the engine warms up, air will also be distributed through the floor vents and the fan speed will be increased. As the temperature inside the car nears the selected value, both the fan speed and the heat will be decreased to a level determined by the system.


Starting in hot weather The system will automatically distribute air through the panel vents at high fan speed and will switch on the A/C compressor (unless the AC OFF switch has been pressed). If the outdoor temperature is above 77°F (25°C), the system might select recirculation after 0-15 seconds if this is required in order to reach the desired temperature. As the temperature inside the car nears the selected value, the fan speed will be decreased to a value determined by the system.


95_US_MY09.book Page 85 Tuesday, April 15, 2008 11:03 AM


Instruments and controls


85


Adaptation of ACC It is also possible to customize the ACC system, e.g. to adapt to driving and weather conditions.


Adaptation and restoration of factory settings is done by holding the respective button depressed approx. 2 seconds until a chime sounds. Make sure the ignition is ON.


Function Operation in AUTO mode


after adaptation The rear window heating will come on after the engine has started if the outside temper- ature is below +5 °C. – This function helps to pre- vent ice or mist forming on the rear window in cold, damp weather. Fuel con- sumption may increase slightly. Seat heating comes on if the system determines that heat- ing is necessary based on the temperature in the seat and the outside temperature.


Factory setting


Heating is selected manually.


Function


Display text in SID during adaptation


ACC:AUTO RDEFR CTRL


Display text in SID when factory settings are restored ACC:MANUAL RDEFR CTRL


ACC:AUTO SEAT HEATING


ACC:MANUAL SEAT HEATING


There are two settings for heating. Repeat- edly pressing the but- ton switches between low output, high output and off.


Example: If you want the ACC system to handle activation and deac- tivation of rear window/door mirror heating, hold the button depressed approx. 2 seconds until a chime sounds. The display shows: ACC:AUTO RDEFR CTRL When “Adaptation of ACC“ is done, it will apply until factory settings are restored.


The following measures are recommended if the occupants feel that it is cold and draughty in the car: 1 Make sure that all the air vents are fully open, including the center rear vent. If this is not enough...


2 Direct the air flow away from the body. If


this is not enough...


3 Raise the temperature setting a degree


or two. If this is not enough...


4 Lower the fan speed.


Troubleshooting and care, see page 244.


95_US_MY09.book Page 86 Tuesday, April 15, 2008 11:03 AM


86


Instruments and controls


Calibration Calibration is carried out automatically after a certain number of starts if the ignition has been switched off for more than 2 hours. If the battery has been disconnected or has run flat, the system will need to be recali- brated. Calibration is started manually as follows: 1 Start the engine.


2 Press


and


at the same


time.


When manual calibration starts, ”ACC:CALIBR. STARTED” appears in SID. Calibration takes approx. 30 seconds. Useful tips (before taking the car to a workshop. We recommend that you contact an authorized Saab workshop.)


If the battery has been disconnected or has run flat, the system will need to be recalibrated. See "Calibration" above. If front seat heating and/or rear window heating do not function satisfactorily, see "Adaptation of ACC" on page 85.


Condensation water When the A/C system is running, the intake air is dehumidified, and the resultant con- densation is drained off through two outlets underneath the floor of the car, in the vicinity of the front doors. It is therefore perfectly normal for water to be seen dripping from these outlets when the car is parked. The warmer the ambient air and the higher the humidity, the more condensation water will form. Formation of ice and mist in extreme weather conditions It is only in the most extreme conditions that icing and misting of window glass are likely to be a problem, e.g. in torrential rain or severe cold coupled with high relative humidity, or when passengers are perspir- ing heavily or wearing wet clothes. The following measures are recommended if such problems should occur: 1 Select AUTO and 21 °C for both temper-


ature zones.


2 Select Defroster.


If this is not enough...


3 Increase the fan speed.


If this is not enough...


4 Select a higher temperature.


(cid:127) (cid:127) 95_US_MY09.book Page 87 Tuesday, April 15, 2008 11:03 AM


Instruments and controls


87


Heated front seats 3
The heating of the seat cushion and back- rest of both front seats is adjustable and thermostat-controlled. The heating is adjustable in two stages.


Ventilated front seats 3
Ventilated front seats, that enhance seating comfort in hot weather, are available as an option on cars equipped with leather-uphol- stered and electrically adjustable seats. Ventilated seats are equipped with two fans that extract the moist air from between the seat and the body. The fans have two speeds.


Heated rear seat cushion 3
Electrically heated seat cushions for the two outer seats in the back are available as an option. The ON/OFF control button for the cushion heating is located on the back of the center console. How long the cushions are heated for depends on the outside temperature. The heating can also be turned off with the button. The button has an integral indicator that is illuminated when the heating is on.


95_US_MY09.book Page 88 Tuesday, April 15, 2008 11:03 AM


88


Instruments and controls


(This page has been left blank.)


95_US_MY09.book Page 89 Tuesday, April 15, 2008 11:03 AM


Saab 9-5 Audio System


89
Saab 9-5 Audio System


Radio _______________ CD player ____________ CD changer 3 ________ MP3 player ___________ Portable player 3 _____ General functions _____ Sound system ________ Technical data ________ Antennas ____________ Error codes __________ Security lock _________


93 99 100 102 104 105 107 108 109 112 112


3 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories).


95_US_MY09.book Page 90 Tuesday, April 15, 2008 11:03 AM


Saab 9-5 Audio System


90
Saab 9-5 Audio System 3
To get the best out of your Saab 9-5 Audio System, we recommend that you read through this entire section. The Saab 9-5 Audio System consists of a head unit with radio, CD player/CD changer 3 for CD and MP3 discs and CD changer 3 in the luggage compartment. The audio system is operated using the steering wheel controls 3 or the control panel buttons.


WARNING


Safety first! Cut off power immediately and contact your Saab dealer if the system begins to emit smoke or smells strange.


All work on the audio system must be carried out by a workshop. We recommend that you contact an authorized Saab dealer.


Audio system activation/deactivation. Volume adjust.


Information on artist, album and song title. Display of radio text.


The tone control is used to adjust tone and speaker set- tings, change CD track or MP3 file and manual adjust radio frequency.


Setup menu.


95_US_MY09.book Page 91 Tuesday, April 15, 2008 11:03 AM


Scroll among preset pages.


The menu option in the display is selected with the corre- sponding pushbutton directly underneath. No function on U.S./CA cars.


Select XMTM 3 program type when the radio is in the XMTM 3 mode. Cars with CD changer 3: insert CD or MP3 disc or discs.


Cars without CD-changer 3: set time and date.


Eject CD or MP3 disc.


Activate radio and change fre- quency band (AM,FM and XMTM 3).


Auto tuning down and change track/file going back in order of play on CD or MP3 disc.


Auto tuning up and change track/file forward in order of play on CD or MP3 disc.


Manual tuning and rapid play back for a track/file on a CD or MP3 disc.


Manual tuning and rapid play forward for a track/file on a CD or MP3 disc.


Activate CD media or portable player.


Saab 9-5 Audio System


91


Steering wheel controls 3


"arrow up"/"arrow down": change preset for radio stations, change track on CD or MP3 player. "Seek UP": auto tuning up, select next track on CD or MP3 disc. Activate radio station scan


SRC: press to switch between AM, FM, XMTM 3, CD, MP3, CD changer or portable player.


VOL: adjust volume.


95_US_MY09.book Page 92 Tuesday, April 15, 2008 11:03 AM


Saab 9-5 Audio System


92
Switching the audio system On/Off The audio system will come on: (cid:127) When the ignition is switched ON and/or


the ON/OFF control is pressed.


Audio settings


Volume Turn the ON/OFF control until the desired volume is obtained. Tone controls


ON/OFF control The audio system will be switched off: (cid:127) When the ON/OFF control is pressed. (cid:127) When the ignition key is removed. (cid:127) One hour after the ignition was switched


OFF, if the ignition key has not been removed.


(cid:127) 1 hour after the audio system has been


switched on if the key is not in the ignition switch.


Tone and speaker settings


Manual tone and speaker settings 1 Press the tone control to open the menu


for tone and speaker settings.


2 Press the pushbutton under the desired


tone/speaker setting.


3 Adjust the selected setting by turning the tone control. The selected settings can also be adjusted by pressing the SEEK, FWD or REV button.


Centering tone and speaker settings Hold the tone control depressed until a chime sounds to center all tone and speaker settings.


Automatic tone setting You can choose to automatically adapt tone setting, Auto EQ (Equalizer), to the tuned station or disc being played. 1 Press the tone control to open the menu


for tone settings.


2 Press the pushbutton under the menu


option Auto EQ label.


3 Press the pushbutton under the desired


tone setting.


4 The tone settings menu automatically


returns to the previous menu within 5 seconds.


Auto EQ menu


95_US_MY09.book Page 93 Tuesday, April 15, 2008 11:03 AM


Radio Press the RADIO BAND button to return to radio mode if another audio source is in use. Selecting a radio station


Selecting a frequency band Press the RADIO BAND button to change frequency band. The selected frequency band appears on the display.


Selecting a preset station Scroll to the desired preset page by press- ing the FAV button and then pressing the pushbutton (1-6) under the desired preset station.


You can also press wheel to select another preset station.


on the steering


or


Saab 9-5 Audio System


93


Storing presets You can store up to 36 radio stations as pre- sets by using the 6 pushbuttons under the display and the FAV button. Press the FAV button to scroll through up to 6 pages with 6 presets per page. Each page can contain a combination of AM, FM and XMTM 3 stations.


Storing the current station as a preset To store the current station as a preset: 1 Press the FAV button until you come to


the preset page (1-6) at which the station is to be stored.


2 Hold the pushbutton depressed under the spot (1-36) at which the station is to be stored. A chime will sound once the station is stored.


Preset stations


Tuning a station


Fine tuning Turn the tone control one increment or press the REV or FWD button to fine-tune the frequency in increments of 0.2 MHz.


Automatic tuning


Press one of the SEEK buttons or the button on the steering wheel for automatic seek tuning. The radio then searches upward in the frequency band for the near- est strong station and stops at that fre- quency.


Manual tuning Turn the tone control or hold the REV or FWD button depressed to seek a frequency manually. Release the control/button to stop at the desired frequency.


Scanning radio stations Hold one of the SEEK buttons or the


button on the steering wheel depressed until a chime sounds for a 5 second sam- pling of each station accessible on the fre-


quency band. Scanning... appears on the


display.


Press one of the SEEK buttons or the button on the steering wheel again to cancel the scan and select the radio station being played at that instant.


95_US_MY09.book Page 94 Tuesday, April 15, 2008 11:03 AM


94


Saab 9-5 Audio System


Number of pages with preset stations To display the number of pages (1-6) with preset stations: 1 Hold the FAV button depressed or press


the MENU button and then press the pushbutton under the menu option FAV 1-6.


Setup menu 2 Select the number of preset pages to be


displayed by pressing the pushbutton under the menu option with the desired number of preset pages (1-6).


Number of preset pages


Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following:


(cid:127) Display radio station name. (cid:127) Display messages from radio stations. (cid:127) This system relies on receiving specific information from these stations and will only work when the information is avail- able. In rare cased, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.


The RDS system is always on. When infor- mation is broadcast from the FM station you are listening to, the station name or call let- ters will be displayed on the display.


Rolling advertisements Some radio stations present rolling adver- tisements in the display. (cid:127) To block rolling advertisements, mark PS-Freeze by pressing the pushbutton directly underneath.


(cid:127) To allow rolling advertisements, deselect


PS-Freeze by pressing the pushbutton directly underneath.


Press the pushbutton under the arrow symbol or wait until the system automati- cally returns to the previous menu.


Radio text Press the i button to show text messages sent by certain radio stations in the display. If there are no text messages, No Info appears on the display.


RDS menu


NOTICE


The menu options AF and REG have no function on US/CA cars.


95_US_MY09.book Page 95 Tuesday, April 15, 2008 11:03 AM


XMTM 3 Satellite Radio Service XMTM is a satellite radio service based in the 48 contiguous United States and Can- ada. XMTM offers a large variety of coast- to-coast channels including commercial free music, news, sports, talk, traffic/ weather (U.S. subscriders), and children‘s programming. XMTM provides digital quality audio and text information that includes song title and artist name. A service fee is required in order to receive the XMTM service. For more information, contact XMTM: In the US. at www.xmradio.com or call 1-800-852-XMXM (9696). In Canada at www.xmradio.ca or call 1-877-GET-XMSR (438-9677). When XMTM is active, the channel name, and number, song title and artist can be dis- played.


Finding a XMTM 3 station The PTY button is used to find XMTM stations when the radio is in the XMTM mode. To find XMTM channels within a desired category, perform the following: 1 Press the RADIO BAND button until the XMTM frequency is displayed. Press the PTY button to display the category labels on the radio display. Continue pressing the PTY button until the desired category name is displayed. 2 Press either of the two pushbuttons below the desired category label to immediately tune to the first XMTM station associated with that category.


3 Turn the tone control, press the buttons below the right or left arrows displayed, or press the right or left SEEK buttons to go to the next or previous XMTM station within the selected category.


4 To exit the category search mode, press the FAV button to display your favorites again.


Saab 9-5 Audio System


95


Remove an XMTM 3 category Undesired XMTM categories can be removed through the Setup menu. To remove an undesired category, perform the following: 1 Press the MENU button to display the


radio Setup menu.


2 Press the pushbutton under the menu


option XM CAT.


3 Turn the tone control to display the cate-


gory you wish to remove.


4 Press the pushbutton under the menu option Remove until the category name


along with the word Removed appears on the display.


5 Repeat the steps to remove more cate-


gories.


NOTICE


The menu option XM CAT can only be accessed when the vehicle is stationary.


95_US_MY09.book Page 96 Tuesday, April 15, 2008 11:03 AM


96


Saab 9-5 Audio System


Restore removed XMTM 3 categories Removed categories can be restored by pressing the pushbutton under the menu option Add when a removed category is dis- played or by pressing the pushbutton under the menu option Restore All.


The XM Categories


Decades Country Hits Christian Rock Urban Jazz & Blues Dance Latin


World Classical Kids News Sports Comedy Talk & Variety Premium


95_US_MY09.book Page 97 Tuesday, April 15, 2008 11:03 AM


Saab 9-5 Audio System


97


XMTM 3 Radio Messages


Radio Display Message Condition XM Updating


Updating encryption code


No XM signal


Loss of signal


Loading XM


Channel Off Air Channel Unavail


No Artist Info


No Title Info


No CAT Info


Acquiring channel audio (after four second delay) Channel not in service Channel no longer available Artist Name/Feature not available Song/Program Title not available Category Name not available


Action Required The encryption code in the receiver is being updated an no action is required. This process should take no longer than 30 seconds. The system is functioning correctly, but the vehicle is in a location that is blocking the XMTM signal. When you move into an open area, the signal should return. The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. This channel is not currently in service. Tune in to another channel. This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No artist information is available at this time on this channel. The system is work- ing properly. No song title information is available at this time on this channel. The system is working properly. No category information is available at this time on this channel. The system is working properly.


95_US_MY09.book Page 98 Tuesday, April 15, 2008 11:03 AM


98


Saab 9-5 Audio System


Radio Display Message Condition Not Found


No Information


XM Theftlocked


No channel available for the chosen category No Text/Informational message available Theft lock active


XM Radion ID


Radio ID label (channel 0)


Unknown


Check XM Receiver


Radio ID not known (should only be if hardware failure) Hardware failure


Action Required There are no channels available for the selected category. The system is working properly. No text or informational messages are available at this time on this channel. The system is working properly. The XMTM receiver in the vehicle may have previously been in another vehicle. For security purposes, XMTM receivers cannot be swapped between vehicles. If this message is received after having your vehicle serviced, check with your Saab dealer. If tuned to channel 0, this message will alternate with the XMTM Radio eight digit radio ID label. This label is needed to activate the service. If this message is received when tuned to channel 0, there nay be a receiver fault. Consult with your Saab dealer. If this message does not clear within a short period of time, the receiver may have a fault. Consult with your Saab dealer.


95_US_MY09.book Page 99 Tuesday, April 15, 2008 11:03 AM


CD player


NOTICE


Do not use CDs with labels or stickers. These labels could detach and cause the audio system to malfunction.


Activate the CD player by inserting a disc or by pressing the CD AUX button if a CD is already loaded.


CD player menu Loading CDs Insert the disc in the slot with the text side up until the mechanism loads the disc. The first track is played. If the disc is wrong-side-up, it will be ejected automati- cally. Once all the tracks have been played, the CD player will restart from track 1. The CD player is turned off by pressing ON/OFF to turn off the audio system or by selecting another audio source.


Removing CDs Press the EJECT button to eject the CD. If you press EJECT without removing the ejected disc, the player will reload the disc after 10 seconds for reasons of safety. Selecting and changing tracks Turn the tone control or press the SEEK but- tons to select or change to the preceding or next track. The track number appears in the display. If the current track has played for at least 10 seconds, you can start the track from the beginning by pressing SEEK (arrow left). If you press SEEK (arrow right) while the last track of the disc is playing, the first track will play. If you press SEEK (arrow left) while the first track of the disc is playing, the last track will play.


The same function applies to the steering wheel.


and


on


Saab 9-5 Audio System


99


Rapid playing tracks To rapid play the current track, hold REV or FWD depressed. Release the button to stop rapid play and return to normal playback. Random playback You can allow the CD player to choose tracks randomly, i.e. not to play the tracks in numerical order. (cid:127) To play tracks randomly, press the push-


button under the menu option RDM.


(cid:127) To resume playing tracks in numerical order, press the pushbutton under the menu option RDM again.


Random playback


95_US_MY09.book Page 100 Tuesday, April 15, 2008 11:03 AM


Saab 9-5 Audio System


100
CD changer 3


NOTICE


Do not use CD or CD-R discs with labels or stickers. These labels could detach and cause the audio system to malfunc- tion.


Activate the CD changer by inserting one or more CD/MP3 discs or by pressing the CD AUX button if one or more discs is already loaded. Loading CDs


Loading a CD 1 Press the LOAD button. The following


appears on the display: Please Wait 2 Wait until the loading mechanism is

Loading...
x