2009 Saab 9 5 Owners Manual

Battery ______________ Drive belts ___________ Wipers and washers ___ Changing bulbs _______ Fuses _______________

188 189

190 192 192 193 193 194 196 196 197 199 200 202 214

Tires ________________ Automatic tire pressure monitoring system ___ Compact spare tire ____ Safety belts __________ Upholstery and trim ___ Textile carpeting ______ Washing the car ______ Waxing and polishing__ Engine compartment __ Touching up the paint _ Air conditioning (ACC) _ Anti-corrosion treatment For long trips_________ Recovery and/or recycling of automotive materials ___________ Headlight aiming ______

220

232 235 240 241 241 242 243 243 243 244 246 247

248 248

3 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories).

95_US_MY09.book Page 188 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

188
Hood The hood release handle is located under- neath the instrument panel. To open the hood: 1 Pull the release handle. 2 The front of the hood will now spring up,

providing access to the secondary safety catch.

Hood release handle

Hood secondary safety catch

3 Push the catch upwards, pushing the hood downward a little bit at the same time. The hood can now be lifted right up.

To close the hood, release it from a height of about 8 - 16 in (20-40 cm). Do not press down on it.

WARNING

Never hold your fingers between the hood and safety catch if lowering but not clos- ing the hood.

Check that the hood is now closed securely.

95_US_MY09.book Page 189 Tuesday, April 15, 2008 11:03 AM

Engine compartment

Car care and technical information

189

Engine compartment 1 Engine-oil dipstick/filler cap 2 Reservoir, brake/clutch fluid 3 Fuse box 4 Expansion tank, coolant 5 Washer-fluid filler cap 6 Battery 7 Turbo unit 8 Ignition discharge module 9 Reservoir, power-steering fluid

95_US_MY09.book Page 190 Tuesday, April 15, 2008 11:03 AM

190

Car care and technical information

Engine families Saab cars imported into the United States and Canada meet all applicable emission control standards. The engine family and appropriate tune-up specifications are iden- tified on a label affixed to the left front inner fender. These engine families meet applicable EPA Federal Standards, California State Stan- dards and Canadian Federal Standards and are equipped with the following systems: (cid:127) Sequential multiport fuel injection system (cid:127) Three way catalytic converter (cid:127) Crankcase emissi ons control system (cid:127) Evaporative emission control system (cid:127) On-Board diagnostic (OBD II) system.

Emission control systems The systems for controlling emissions to the atmosphere require regular checking and adjustment at the intervals specified in the service program. In addition to meeting the exhaust emission regulations and thereby helping to keep the environment clean, a correctly tuned engine will also give maximum fuel economy.

WARNING

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of CA to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of Cal- ifornia to cause cancer and birth defects or other reproductive harm.

Car care and technical information

191

NOTICE

The Trionic engine management system continuously monitors the operation of these systems and has on-board diag- nostic capabilities (OBD II). If the ”Service Engine Light also known as CHECK ENGINE” lamp in the main instrument illuminates, this indicates that the Trionic ECM has detected a problem. The car will continue to operate, but per- formance may be diminished. You should have your car checked by a Saab dealer as soon as possible.

ORVR (Onboard Refueling Vapor Recovery) Hydrocarbon vapors formed when refueling will be recovered by the car and not released into the atmosphere. The hydro- carbons are absorbed in a evaporative emission canister. When the engine is sub- sequently started, the evaporative emission canister is gradually purged as air is sucked into it through a shut-off valve. The hydro- carbon/air mixture passes through the evap canister purge valve and into the engine where it is burned. When refueling, make sure you screw the filler cap on and keep turning until it has clicked at least 3 times. Otherwise, it is pos- sible for the CHECK ENGINE light to illumi- nate. Refueling, see page 146.

95_US_MY09.book Page 191 Tuesday, April 15, 2008 11:03 AM

Saab Trionic engine management system The Saab Trionic engine management system is a unique Saab development that combines sequential multiport fuel injection, electronic distributorless ignition and turbo- charger boost pressure control into one sys- tem. The Trionic engine control module (ECM) monitors many different engine parameters such as:

Intake manifold pressure Intake air temperature

(cid:127) Crankshaft position (cid:127) Engine coolant temperature (cid:127) Throttle position and (cid:127) The oxygen content of the exhaust gases. The ECM receives information regarding engine knocking from a sophisticated feed- back function in the ignition discharge unit. By processing all of this information, the Tri- onic system can control fuel injector open- ing duration, ignition timing and turbo- charger boost pressure to provide excellent engine performance while maintaining low emissions and fuel consumption.

(cid:127) (cid:127) 95_US_MY09.book Page 192 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

192
Engine The 2.3-liter model is a transverse, 4-cylin- der in-line engine with twin overhead cam- shafts and 4 valves per cylinder. This engine is equipped with balance shafts that reduce engine vibration to a minimum. The balance shafts are chain driven and rotate at twice the speed of the crankshaft. They produce forces and torques that are opposed to those generated by the pistons and connecting rods, an effect that occurs twice for each revolution of the engine. Engine noise is also reduced as the counter-rotating shafts counteract the vibra- tion from the moving parts of the engine. The transmission, located on the right (viewed from the front), is integrated with the engine. All models have front-wheel drive.

The oil level must not be allowed to drop below the MIN mark on the dipstick, nor should oil be filled beyond the MAX mark, as this can lead to excessive oil consumption. The distance between the MIN and MAX marks on the dipstick corresponds to a volume of approximately 1.05 qts (1 liter). When necessary, add oil of the recom- mended grade via the dipstick tube. Recommended oil grade, see page 260.

NOTICE

(cid:127) Do not operate the engine with a low

oil level.

(cid:127) Change engine oil and oil filter as pre-

scribed in the service programme. (cid:127) Only use the recommended oil type. Follow the three points listed above to avoid severe engine damage. More frequent oil changes are recom- mended if your vehicle is operated under certain conditions, see page 252.

Balance shafts

Engine oil Checking the oil level Check the engine-oil level regularly. This should be done after the engine has been run to normal temperature and then allowed to cool for 2–5 minutes, with the car stand- ing on level ground. Remove the dipstick and wipe it clean before checking the level.

95_US_MY09.book Page 193 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

193

Transmission fluid Manual transmission Check and top up the fluid in accordance with the service program. Automatic transmission Check and top up the fluid in accordance with the service program.

Coolant

WARNING

(cid:127) Proceed with caution if the radiator is

boiling when you open the hood. Never remove the expansion-tank filler cap when the radiator is boiling.

(cid:127) The cooling system is pressurized – hot coolant and vapor can escape when the filler cap is released. These can cause injury to your eyes and burns. Loosen the cap carefully, and let the engine cool before removing the cap.

(cid:127) Exercise care when adding coolant. Coolant on hot surfaces constitutes a fire risk.

There is an overpressure in the cooling sys- tem. Coolant temperatures can sometimes exceed 212°F (100 °C). The expansion tank is transparent to facili- tate checking of the coolant level. When the engine is cold, the coolant shall lie on or just above the KALT/COLD mark on the expansion tank.

Coolant expansion tank

If the message ”Coolant level low. Refill.” is displayed on the SID, check the level of fluid in the expansion tank. Top up, as necessary, with equal parts of clean water and Saab-approved coolant. Coolants of a different brand could damage the engine or cooling system. We therefore recommend strict use of coolants that have been approved by Saab. If the expansion tank is empty when coolant is added, run the engine to normal temper- ature and top up again, as necessary.

95_US_MY09.book Page 194 Tuesday, April 15, 2008 11:03 AM

194

Car care and technical information

The cooling system is charged at the factory with coolant containing a 45 % concentra- tion of a combined antifreeze and corrosion inhibitor. A weaker mixture will result in reduced anticorrosion protection. For protection against freezing in very cold weather, a stronger concentration will be needed. A 60 % concentration of antifreeze will pro- vide protection at temperatures down to –58°F (–50°C). The coolant does not normally have to be changed during the service life of the car. The type of coolant used has a reddish color and should not be mixed with other types of coolant. Saab Original coolant should be used all year round. Only use coolant approved by Saab.

Note: If incorrect coolant is used or added, the life-time properties will be affected. Even if the coolant is flushed from the system and replaced with life-time coolant, life-time properties are no longer retained and the coolant must then be drained and replaced at regular intervals.

NOTICE

Always mix the antifreeze with the appropriate volume of water before adding it to the cooling system. If pure antifreeze is added, the engine could still freeze and be damaged. This is because the antifreeze will not mix properly with the coolant before the thermostat has opened to allow full circulation.

Brake and clutch fluid

WARNING

Brake fluid deteriorates as it becomes old. Because it is hygroscopic, it absorbs water from the air and, in time, could allow vapor to form in the brake system, thus reducing its performance. It is therefore important that brake fluid be changed reg- ularly, as specified in the service pro- gram.

Checking the fluid level The combined brake and clutch-fluid reser- voir is transparent to facilitate checking of the fluid level. The level should be between the MAX and MIN marks. Top up, as necessary, with DOT 4 fluid. Do not use DOT 5 brake fluid.

95_US_MY09.book Page 195 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

195

Brake pad wear indicators The outboard brake pads on the front wheels incorporate pad-wear indicators. When the lining is down to 0.11 in (3 mm), the pad will produce a screeching, squeal- ing or scraping noise when the brakes are applied. New pads should be fitted without delay. Brake pads should only be changed by a workshop. We recommend that you con- tact an authorized Saab dealer.

Use only new brake fluid from a sealed container. Check that there are no leaks in the brake system. The brake fluid level will fall somewhat as the brake pads wear. The MAX level in the reservoir corresponds to the amount of brake fluid required with new brake pads. If the fall in fluid level is moderate, due to normal brake pad wear, topping up is not necessary. Changing of the brake fluid should be carried out by a workshop. We recom- mend that you contact an authorized Saab dealer. The vehicle´s regular braking system is adjusted automatically, but the parking brake has to be adjusted manually. This work, involving adjustment of the parking brake cables and brake pads, must only be carried out by a workshop. We recommend that you contact an authorized Saab dealer.

Brake and clutch-fluid reservoir

It is not possible to detect, through abnormal pedal or parking brake-lever travel, whether brake pads are worn and need replacing. It is therefore essential that brake pads be checked regularly, as specified in the service program.

NOTICE

Avoid spilling brake fluid onto paintwork, since it can cause the paint to bubble and lift. If any brake fluid is spilled, the area should be flushed with large quantities of water as quickly as possible.

Air filter

WARNING

(cid:127) For Service and Repair, parts equiva- lent to those used by Saab should be used.

(cid:127) Be aware that some non standard

replacement parts may put you in an unsafe condition, even if they might fit.

95_US_MY09.book Page 196 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

196
Power steering fluid

Power steering fluid reservoir

WARNING

(cid:127) Do not fill the power steering fluid to

above the MAX mark. Too much fluid can result in leakage.

(cid:127) Power steering fluid on hot engine components constitutes a fire risk.

Check the level of the power steering fluid in the reservoir regularly, in accordance with the service program. The wheels should point forward during the check. Clean around the cap before it is unscrewed. Clean the dipstick. Screw in the cap completely again before checking the level. The oil should lie between the MAX and MIN marks when the oil temperature is about 70°F (+20°C). If the oil is colder the level can be lower, and in higher temperatures the level can be higher, both of which are acceptable. Top up with ”Power Steering Fluid CHF 11S or CHF 202”.

95_US_MY09.book Page 197 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

197

Battery

WARNING

(cid:127) Work on the battery may entail an

explosion hazard, since the battery gives off hydrogen which forms an explosive mixture with the oxygen in the air. For this reason, always avoid sparks or open flames when working near the battery.

(cid:127) The battery contains corrosive sulfuric

acid. Always wear a face mask or goggles when working on the battery.

(cid:127) If battery acid gets into the eyes or

splashes the skin or clothing, wash the affected area liberally with water. If acid gets into the eyes or a large quantity makes contact with the skin, seek medical help.

(cid:127) Battery posts, terminals and related accessories contain lead and lead compounds. Wash your hands after handling.

The battery is provided with a cover to protect it from radiated heat. If the battery is exposed to high temperatures, its life will be shortened. To remove the cover, release the two clips along its long sides. The cover fits the standard battery installed in the car. If a new battery is to be fitted, make sure that its dimensions are the same as the standard one. The battery is maintenance free.

NOTICE

A discharged battery can freeze and frac- ture. Batteries should therefore always be stored away from frost.

If frequent short journeys are made, the bat- tery may need to be given a booster charge. This can be done either using a battery charger or by taking the car for a long run. A car with a standard equipment specifica- tion and a fully charged battery can be left for up to 40 days and still have a sufficient charge for starting. If extra equipment is fit- ted, such as a car phone, the charge may only be sufficient for about 15 days.

Charging/replacing the battery

NOTICE

To avert the danger of short-circuiting between the positive (+) terminal on the battery and the inlet manifold on the engine, always disconnect the negative (–) battery lead first and reconnect it last.

Connect the positive lead to the positive (+) battery terminal (red), and the negative lead to a good ground point, e.g. the lifting lug at the front of the engine. To remove the battery, always disconnect the negative (black) lead first and reconnect it last when fitting the new battery. The battery size must comply with DIN 53735 MFI 230/2.16.

95_US_MY09.book Page 198 Tuesday, April 15, 2008 11:03 AM

198

Car care and technical information

NOTICE

(cid:127) If boost charging never use anything but a 12-volt charger, see page 186. (cid:127) Never reverse the polarity of the bat- tery by connecting the leads to the wrong terminals. The red, positive lead connects to the positive (+) termi- nal, and the black, negative lead to the negative (–) terminal.

(cid:127) Serious damage can occur to the car´s electrical system if a battery or alterna- tor lead is disconnected while the engine is running.

(cid:127) The nut on the battery clamp should be tightened to a torque of 10 Nm.

Battery

Correct position for battery clamp

95_US_MY09.book Page 199 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

199

The alternator is situated on the right-hand side of the engine, adjacent to the bulkhead. It is driven via a Poly-V-belt from the crank- shaft pulley. The Poly-V-belt also drives the water pump, the A/C compressor and the steering servo pump. The belt tension is critical and is adjusted automatically by the belt tensioner. See also page 59, ”Warning, charging”.

Drive belts

WARNING

(cid:127) Keep hands and clothing clear of drive

belts when engine is running. (cid:127) Always stop the engine before

inspecting drive belt.

(cid:127) The radiator fan is electric and can

start even when the engine is switched off.

NOTICE

Serious damage can be done to the car’s electrical system if an alternator lead is disconnected while the engine is running.

95_US_MY09.book Page 200 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

200
Wipers and washers Check and clean all wiper blades regularly. If poor wiper performance is experienced, clean the windshield with a quality glass cleaner. This is particularly important if the car has been through an automatic car wash, as these sometimes leave a wax coating on the windshield. If wiper performance is still unsatisfactory, fit new blades.

Changing the windshield wiper blades 1 Hold the wiper arm and push the two

catches off the arm.

2 Move the blade along the extension of

the arm.

Fitting the wiper blade 1 Slide the new blade onto the arm until it locks in position. Make sure that the end of the wiper arm is within the blade bracket.

2 Check that the blade is seated correctly.

Rear window, SportCombi 1 Detach the blade from the arm by pres- sing the blade’s mounting from underne- ath.

2 Install a new blade by pressing the shaft

of the blade in the arm’s mounting.

The washer jet, which is located next to the high-mounted brake light, is not adjustable.

95_US_MY09.book Page 201 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

201

Cleaning/adjusting the washer jets

Washer-fluid filler cap

The headlights have high-pressure washers 3

Washer jets The washer jets can be adjusted and, if necessary, unclogged by means of a pin.

Washers The washer-fluid reservoir holds 6.4 quarts (6 liters). When "Washer fluid level low. Refill." comes up on the SID, the reservoir is down to about 1 quart (1 liter) of fluid. Add at least 50 % of washer- fluid to water to prevent freezing and for effective cleaning.

WARNING

Take care not to spill washer fluid concentrate onto hot surfaces. Washer fluid concentrate contains flammable ingredients such as alcohol.

95_US_MY09.book Page 202 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

202
Changing bulbs

WARNING

Before changing a bulb in the engine bay, switch off the engine to avoid danger of fingers and hands being injured by moving parts. The radiator fan can start up even when the engine is switched off. Xenon headlights 3 are high voltage and must therefore be changed at a workshop. We recommend that you contact an authorized Saab work- shop. Work involving high-voltage components is potentially lethal.

NOTICE

(cid:127) Since the headlight lenses are made

of plastic, rinse dried-on dirt with water and allow it time to soften up before cleaning the lenses. Avoid rubbing the lenses when dry and never use solvents.

(cid:127) Use de-icer spray instead of scraping

the ice off.

Check that the new bulb is working when finished. Use only "Long Life" bulbs. Headlight aiming, see page 248.

NOTICE

(cid:127) Do not fit bulbs with a higher rating

than 55 W, since the headlight reflec- tor and the wiring of the car are not designed for a higher wattage.

(cid:127) Switch off the ignition before chang-

ing a bulb, to avoid possible short-cir- cuiting.

(cid:127) Do not touch the glass of the bulbs

with your fingers. The oil on your skin can shorten the life of the bulb.

Xenon headlight 3
Xenon headlights produce roughly twice as much light as halogen bulbs and have a sig- nificantly longer service life. The lamp units consist of a gas discharge lamp containing xenon. When the lights are switched on a very high voltage activates the xenon gas. The lamps soon reach full intensity. Cars with xenon headlights have automatic levelling. The levelling system comprises two sensors, one on the front axle, one on the rear axle and a control unit under each of the two headlight housings. Headlight alignment is regulated automatically to pre- vent dazzling oncoming traffic. Alignment is also adjusted during braking.

95_US_MY09.book Page 203 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

203

The three covers of the headlight. The left-hand cover is for the direction indicator. Replacement of this bulb should be carried out by a workshop. We recommend that you contact an authorized Saab workshop.

Headlight bulb for high beam (Halogen) On cars equipped with Xenon lamps the Halogen lamps are used only for high beam flasher if the daytime running lights are deacti- vated and the headlight switch is in the off position (otherwise Xenon lamp is utilized): 1 Remove the cover from the back of the lamp unit. To improve accessibility to the right-hand side, hold back the induction air hose. To improve accessibility to the left-hand side, remove the battery cover. Release the two clips along the long sides of the cover.

2 Hold the connector and move the bulb up and down slightly while

pulling it out.

3 Detach the connector from the bulb. 4 Fit the new bulb in the connector without touching the lens with

fingers.

5 Align and fit the bulb in its guide in the reflector by moving it up

and down slightly while pushing it forward.

6 Fit the cover.

95_US_MY09.book Page 204 Tuesday, April 15, 2008 11:03 AM

204

Car care and technical information

Low beam bulb 3
On certain variants the low beam bulb is fitted in the same way as the high beam bulb, without spring clips, see previous page.

Headlight bulb for low beam (Halogen) 1 Take off the cover from the back of the lamp unit. To improve

accessibility to the right-hand headlight, hold aside the induction air hose. To improve accessibility to the left-hand headlight, remove the battery cover. Release the two clips along the long sides of the cover.

2 Unplug the connector. 3 To remove the spring clip, push it in and then move it to the right. 4 Remove the bulb. 5 Without touching the glass with your fingers, insert the new bulb. 6 Line up the bulb with the guide in the reflector and secure it with

the spring clip.

7 Plug in the connector. 8 Fit the cover.

Contact an authorized Saab workshop if a Xenon headlight requires replacement

95_US_MY09.book Page 205 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

205

Front direction indicator Direction indicator bulb replacement should be carried out by a workshop. We recommend that you contact an autho- rized Saab dealer.

Parking-light bulb

Parking-light bulb The parking light bulb is situated in the lower edge of the lamp housing. The bulb holder has been extended to facil- itate replacement. 1 Pull the extended bulb holder straight

out.

2 Change the bulb. 3 Make sure that the O-ring is correctly

positioned so as to seal against the lamp housing. When the bulb holder is slid in, it does not matter which direction the bulb holder grip is held.

Front fog lights

Front fog lights 3

WARNING

Never crawl under a car that is supported only by a jack. Always use axle stands. Refer to the information on jacks on page 237.

1 From under the front bumper, grip the bulb holder and twist counterclockwise.

2 Unplug the connector. 3 Change the bulb. Refit in the reverse order.

95_US_MY09.book Page 206 Tuesday, April 15, 2008 11:03 AM

206

Car care and technical information

13

Rear light clusters, 9-5 Sedan 1 Direction indicators 2 Stop lights and taillights 3 Reversing lights 4 Rear fog light 5 High-mounted brake light

Rear light clusters, 9-5 SportCombi 1 Direction indicators 2 Stop lights and taillights 3 Reversing lights 4 Rear fog light 5 High-mounted brake light

Rear light cluster, 9-5 Sedan The bulbs for the lamps in the rear light clus- ter are accessed from the luggage compart- ment. 1 Lower the flap (secured with catches). 2 Squeeze the plastic lugs and remove the

bulb holder.

3 The bulb has a bayonet fitting. Press in

the bulb and twist it counterclockwise.

4 Change the bulb.

95_US_MY09.book Page 207 Tuesday, April 15, 2008 11:03 AM

Trunk lid light and taillights, 9-5 Sedan Before changing bulbs in the trunk, you must first release the trim at the foot of the trunk. This involves removing the handle and the three trim fasteners (studs). 1 Unscrew the handle on the inside of the

tailgate.

2 Using the peg in the top of the screw-

driver handle, push in the button in the center of the studs. 3 Remove the studs.

Car care and technical information

207

Refitting the trim 1 Reset the studs by pushing back the

center buttons so that they protrude by 0.2 inch (5 mm).

2 Insert the studs through the trim and tail- gate panel. Press the center buttons in, flush with the collar.

3 Screw the handle back onto the trunk.

Changing bulbs 1 Squeeze together the silver plastic lug and the electrical connection and with- draw the lamp holder.

2 The bulb has a bayonet fitting. Press in

the bulb and twist it counterclockwise.

3 Change the bulb.

95_US_MY09.book Page 208 Tuesday, April 15, 2008 11:03 AM

208

Car care and technical information

High-mounted stop lights, 9-5 Sedan The bulbs can be accessed after the panel in the rear headlining has been removed. 1 Remove the panel by carefully pushing

in the two clips, one at the time.

2 Release the bulb holder, which is

retained by a clip at either end.

3 Withdraw the bulb gently straight back. 4 Push in the new bulb. 5 Refit the bulb holder. 6 Replace the panel by carefully pushing the panel towards the headlining so that the two clips engage their respective slot.

High-mounted stop lights 1 Panel 2 Retaining clips 3 Bulbs

Rear lights clusters, 9-5 SportCombi 1 Open the tailgate. 2 Remove the two screws securing the

light cluster to the body.

95_US_MY09.book Page 209 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

209

Reassembly 1 Align the fastener with the hole in the

body.

2 Press the lamp unit home into the body

until you hear a click.

3 Fit the screws.

3 Remove the two screws securing the

light cluster to the body.

4 Pull the light cluster rearwards and angle it outwards (it is seated quite firmly).

5 Release the fastener from the body.

Reinsert the fastener into the groove in the light cluster. Press in the fastener until you hear a click.

6 Take out the bulb holder. 7 Press in the bulb and twist it counter-

clockwise.

8 Change the bulb. 9 Check that the new bulb works.

95_US_MY09.book Page 210 Tuesday, April 15, 2008 11:03 AM

210

Car care and technical information

Tailgate bulbs, 9-5 SportCombi 1 Turn the lock a quarter turn (90°) with a

screwdriver or the ignition key.

2 Open and remove the cover. 3 Remove the bulb holder by pressing the

plastic lug to the side.

4 Press in the bulb and twist it

counterclockwise. 5 Change the bulb. 6 Check that the new bulb is working.

Reassembly 1 Place the two ”hinges” in the recess in

the tailgate.

2 Then push the ”hinges” into the recess

and close the cover.

3 Turn the lock a quarter turn.

95_US_MY09.book Page 211 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

211

License-plate light The lens is not screwed in place. It is held in place with snaps. 1 One of the short sides of the lens

contains a recess for a small screw- driver. Insert a screwdriver and prise out the lens.

2 Fit the new bulb. 3 When refitting the lens, the short side without the screwdriver recess should be inserted first.

Side direction indicators 1 Slide the lamp fitting forward and pull out

the back.

2 Remove the bulb. 3 Change the bulb. On refitting, make sure that the spring in the lamp fitting engages the edge of the open- ing in the body panel.

Courtesy lights (front doors and floor) and luggage-compartment lighting 1 Insert a screwdriver carefully into the slot in the end of the lamp fitting. Ease the fitting off to gain access to the bulb.

2 Bend out one of the contacts and

remove the bulb. 3 Change the bulb. On refitting, insert the connector-end of the lamp fitting first.

95_US_MY09.book Page 212 Tuesday, April 15, 2008 11:03 AM

212

Car care and technical information

Dome light, front 1 Ease the leading edge of the glass out

of the overhead panel.

2 Release one of the contacts and remove

the bulb.

Dome light, rear 1 Remove the entire overhead panel:

ease out the trailing end first, and then both front edges. 2 Fit the new bulb.

3 Fit the new bulb.

Glove-compartment illumination 1 Insert a small screwdriver in the slot in the end of the lamp fitting and ease it out to gain access to the bulb.

2 Bend out one of the contacts and

remove the bulb. 3 Fit the new bulb. On refitting, insert the connector-end of the lamp fitting first. Other bulbs If any other bulbs need changing, you are advised to take the car to a workshop. We recommend that you contact an authorized Saab dealer.

95_US_7carcare_MY09.fm Page 213 Tuesday, April 15, 2008 11:45 AM

Car care and technical information

213

10

Bulb table

Wattage # Cap 55 1 H7
2 H8 35
3 P21W 21

4 P21/5W 21/5
5 R10W 10

6 R5W 5 7 Xenon

w9U 8 T4W 9 WY5W/

W5W

10 W2W 1.2

NOTICE

Headlight Fog light Reversing lamp; rear fog lamp; rear direc- tion indicator Stop/tail lamp Dome light; courtesy lights; glove com- partment; luggage compartment Safety belt reminder; license-plate lighting Reading light, overhead panel

Reading light, rear Side indicators (yellow);/ high-mounted stop light (9-5 Sedan); parking lights Switches

Only fit lamps of the specified rating. Lamps of the wrong wattage could damage the wiring harness and electronics.

A special kit containing spare bulbs and fuses is available as an accessory from your Saab dealer. A storage space for this is pro- vided adjacent to the toolkit and jack, under the panel in the luggage compartment.

95_US_MY09.book Page 214 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

214
Fuses

WARNING

To avoid the risk of short-circuiting and/or fire breaking out in the electrical system, the following advice should be heeded: (cid:127) Always consult a workshop before modifying or adding any electrical equipment. We recommend that you contact an authorized Saab dealer. Failure to do so can result in the elec- trical system being damaged.

(cid:127) Never replace a fuse with one having a higher/lower rating than specified (see page 216). The color of the fuse indicates its amperage.

(cid:127) If the same fuse blows repeatedly,

have the electrical system checked by a workshop. We recommend that you contact an authorized Saab dealer. (cid:127) If a MAXI fuse blows, it means that

there is a major fault in the electrical system. Have the car checked by a workshop. We recommend that you contact an authorized Saab dealer.

Sound fuse / Blown fuse

The fuses are housed in two fuse panels: one at the end of the instrument panel on the driver’s side, and one under the hood. To check if a fuse has blown, first remove it from the panel (see below). If the filament is broken, the fuse has blown. A special tool for removing fuses is provided at the bottom of the fuse panel at the end of the instrument panel. Simply push the tool onto the fuse, squeeze and remove the fuse.

Fuse panel in instrument panel

Fuse box under the hood

95_US_MY09.book Page 215 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

215

DICE / TWICE DICE = Dashboard Integrated Central Elec- tronics TWICE = Theft-Warning Central Electronics DICE and TWICE are electronic control modules that monitor and control a variety of functions:

DICE controls (among other things): (cid:127) Front lights and interior lighting

Instrument illumination Intermittent wiper operation

(cid:127) Electric heating of rear window and door

mirrors

(cid:127) Cooling fans

Maxi fuses under the hood

Maxi fuses The Maxi fuses are housed in the fuse box under the hood. These fuses can be checked in the same way as the other fuses. The Maxi fuses are designed to protect the car’s electrical system from being dam- aged. Each Maxi fuse protects a number of electrical circuits and functions and there- fore has a higher rating (amperage) than the standard fuses. No spare Maxi fuses are supplied with the car.

NOTICE

If a Maxi fuse blows, it means that there is a major fault in the electrical system. Have the car checked without delay by a workshop. We recommend that you con- tact an authorized Saab dealer.

TWICE controls (among other things): (cid:127) Central locking. (cid:127) Car alarm (Anti-theft system) (cid:127) Engine immobilizer (cid:127) Autochecking of lights. (cid:127) Electric heating of rear seat (cid:127) Safety belt reminder (cid:127) Electrically adjustable passenger seat The DICE and TWICE control modules are linked to a data bus, which is basically an information carrier that allows information to be exchanged between all the control mod- ules and components connected to the bus. If a fault occurs in any of these components, diagnostic faults codes are set in the rele- vant control module, which facilitates fault diagnosis. We recommend that you contact an authorized Saab dealer. The scan tool connector for fault diagnosis is located under the instrument panel on the drivers side.

(cid:127) (cid:127) 95_US_MY09.book Page 216 Tuesday, April 15, 2008 11:03 AM

216

Car care and technical information

B C 1 2 3 4 5 6

6B

987

10

11

12

13

14

15 16

16B

17

18

19

20

21

22

23 24

25 26 27 28 29 30 31

32

33

34

35

36

37

38

39

Fuse panel in instrument panel

# Amp Function

Trailer lights Automatic transmission

30
10
7.5 Electric door mirrors; DICE: manual beam length

15

adjustment 3
Brake lights; Park Brake Shift Lock (cars with auto- matic transmission) Reversing lights Parking lights and taillights, left Parking lights and taillights, right

15
10
10
7.5 DICE / TWICE 30

Electric windows, right; trailer charging

10

15
15

6B

7.5 Brake lights, trailer 10
15

Engine injectors Trunk lighting; trunk lock; door lighting; parking assistant 3; SID Audio System; CD changer 3
Heating, rear seat 3; moonroof 3, remote control receiver Electrically adjusted passenger seat 3

30
11
7.5 Automatic transmission 3
12
Audio System, amplifier 20
13
Ignition system, engine 30
14
20
Fuel pump 15
DICE (direction indicators) 16
20
OnStar 3
16B – Engine-management system; main instrument; 17
20
DICE/TWICE Door-mirror heating; rear-window heating OnStar 3; Telematics 3
ACC; interior lighting; rear fog light; high beam flasher Audio System; rear-view mirror; load angle sensor 3; navigation 3; Cruise Control 3
Interior fan Central locking; navigation 3; door mirror memory 3
Main light switch Electrically adjustable driver’s seat

18
19
20
21

22
23
24
25

40
10
15
10

40
15
20
30

95_US_MY09.book Page 217 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

217

26

27
28
29

30

31

32
33
34
35
36
37
38
39

7,5 Driver seat memory 3; mirrors memory 3;

moonroof 3; parking assistant 3; seatbelt reminder; ACC Engine-management system; SID; main instrument

10
7.5 Airbag 7.5 ABS/ESP® 7.5 Starter motor; transmission control module (cars with

automatic transmission)

7.5 Cruise control 3; water valve; fog lights, front 3; rain

sensor 3
–

12-volt socket (cigarette lighter) front/rear Daytime running light Electric windows, left

– 7.5 Direction-indicator switch 30
15
30
30 Windshield wipers 30
20

Electric heating, front seats 3
Limp-home solenoid

B C1 C2

L1

L2

Relay panel under instrument panel

C1 C2

Function – Electric heating of rear seat – – – Main relay (engine management system) – Fuel pump Ignition switch Rear-window / door mirrors heating

95_US_MY09.book Page 218 Tuesday, April 15, 2008 11:03 AM

218

Car care and technical information

L1
L2

– Starter relay Limp-home function –

13

17

10

14

11

15

10

11

12

13

14

12

16

15

16

17

Fuse box under hood Fuses

Amp Function 40 Radiator fan, high speed 40 ABS/ESP® 30 ABS/ESP® 7.5 Load angle sensor (cars with xenon headlights) 15 Heater 10 A/C; car alarm siren 15 Bulb test – 20 Headlight washers

–

95_US_MY09.book Page 219 Tuesday, April 15, 2008 11:03 AM

10
11
12
13
14
15
16
17
18

15 High beam headlight, left 15
Low beam headlight left 15 High beam headlight, right 15
Low beam headlight, right 30 Radiator fan, high speed 15 Fog lights (front spoiler) 20 Wiper, rear 15 Horn –

–

Car care and technical information

219

Relays

10
11
12
13
14
15
16
17

Function Bulb test; head light; high beam flasher Headlight washer Front fog lights Wiper, rear (9-5 SportCombi) – – Rain sensor Radiator fan, low speed Radiator fan, high speed A/C-compressor Radiator fan, high speed, right fan Horn Extra lights (accessory) High beam headlight Low beam headlight – Windshield wipers

95_US_MY09.book Page 220 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

220
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Saab Warranty and Service Record Booklet for details.

WARNING

Poorly maintained and improperly used tires are dangerous. (cid:127) Overloading your tires can cause

overheating as a result of too much friction. You could have an blow-out and a serious accident. See “Loading Your Vehicle” on page 229.

(cid:127) Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold.

(cid:127) Overinflated tires are more likely to be cut, punctured or broken by a sudden impact – such as when you hit a pot- hole. Keep tires at the recommended pressure.

(cid:127) Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.

Adjust the tire pressure to match the current load and speed of the car (see page 263). The stated tire pressures apply to cold tires, i.e. tires that are the same temperature as the outside air temperature. Tire pressure increases as the tires become warm (e.g. during highway driving) by approximately 0.3 bar (4 psi). When the temperature of the tires changes by 50°F (10°C), the tire pres- sure will change 0.1 bar (2 psi). Never reduce the pressure of a hot tire. If the tires are hot when you check them, only increase the pressure, if necessary.

Inflation - Tire Pressure The Tire-Loading Information label shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehi- cle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Notice: Don’t let anyone tell you that underinflation or overinflation is all right. It’s not. If your tires don’t have enough air (underinflation), you can get the following: (cid:127) Too much flexing (cid:127) Too much heat (cid:127) Tire overloading (cid:127) Bad wear (cid:127) Bad handling (cid:127) Bad fuel economy

If your tires have too much air (overinfla- tion), you can get the following: (cid:127) Unusual wear (cid:127) Bad handling (cid:127) Rough ride Needless damage from road hazards

95_US_MY09.book Page 221 Tuesday, April 15, 2008 11:03 AM

Car care and technical information

221

High speed operation

WARNING

Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require infla- tion pressure adjustment for high speed operation. When speed limits and road conditions are such that a vehicle can be driven at high speeds, make sure the tires are rated for high speed operation, in excellent condition, and set to the correct cold tire inflation pressure for the vehicle load.

Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tight- ened. See page 239.

WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. See “Changing a wheel” on page 237.

When to check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gauge to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they’re underinflated. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. Tire Inspection and Rotation Tires should be rotated every 10,000 miles (16 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It Is Time for New Tires” on page 222 and “Wheel Replacement” on page 225 for more infor- mation. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehi- cle. The first rotation is the most important. When rotating your tires, always use the correct rotation pattern. Left front tire to left rear. Left rear tire to right front. Right front to right rear. Right rear to left front.

95_US_MY09.book Page 222 Tuesday, April 15, 2008 11:03 AM

222

Car care and technical information

Flat spotting All tires get hot, especially on long journeys or when the car is driven hard. After the car has been parked with hot tires and the tires have cooled down, a flat spot can form in the tire, where it is in contact with the ground. The same can occur if the car has not been moved for a long time. Flat spots can cause vibration that can be felt through the steering wheel, similar to that experienced when the wheels need bal- ancing. Flat spots of this type disappear once the tires get hot again, usually after 10–15 miles (20–25 km) of driving at cruising speed.

When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following