2006 Saab 9 5 Owners Manual

Download PDF Manual
Calibration is carried out automatically after a certain number of starts if the ignition has been switched off for more than 2 hours. If the battery has been disconnected or has run flat, the system will need to be recali- brated. Calibration is started manually as follows: 1 Start the engine. 2 Press time. and at the same When manual calibration starts, ACC:CALABRATION STARTED appears in SID. Calibration takes approx. 30 seconds. Useful tips (before taking the car to a workshop. We recommend that you contact an authorised Saab workshop.) If the battery has been disconnected or has run flat, the system will need to be recalibrated. See "Calibration" above. If front seat heating and/or rear window heating do not function satisfactorily, see "Adaptation of ACC" on page 85. Condensation water When the A/C system is running, the intake air is dehumidified, and the resultant con- densation is drained off through two outlets underneath the floor of the car, in the vicinity of the front doors. It is therefore perfectly normal for water to be seen dripping from these outlets when the car is parked. The warmer the ambient air and the higher the humidity, the more condensation water will form. Formation of ice and mist in extreme weather conditions It is only in the most extreme conditions that icing and misting of window glass are likely to be a problem, e.g. in torrential rain or severe cold coupled with high relative humidity, or when passengers are perspir- ing heavily or wearing wet clothes. The following measures are recommended if such problems should occur: 1 Select AUTO and 21 °C for both temper- ature zones. 2 Select Defroster. If this is not enough... 3 Increase the fan speed. If this is not enough... 4 Select a higher temperature. The following measures are recommended if the occupants feel that it is cold and draughty in the car: (cid:127) (cid:127) 95usM06.book Page 87 Thursday, November 17, 2005 8:59 AM Instruments and controls 87 Heated front seats The heating of the seat cushion and back- rest of both front seats is adjustable and thermostat-controlled. The heating is adjustable in two stages, 0-1-2-0... Ventilated front seats Ventilated front seats, that enhance seating comfort in hot weather, are available as an option on cars equipped with leather-uphol- stered and electrically adjustable seats. Ventilated seats are equipped with two fans that extract the moist air from between the seat and the body. The fans have two speeds, 0-1-2-0... Heated rear seat cushion Electrically heated seat cushions for the two outer seats in the back are available as an option. The ON/OFF control button for the cushion heating is located on the back of the centre console. How long the cushions are heated for depends on the outside temperature. The heating can also be turned off with the button. The button has an integral indicator that is illuminated when the heating is on. 95usM06.book Page 88 Thursday, November 17, 2005 8:59 AM 88 Instruments and controls (This page has been left blank.) 95usM06.book Page 89 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 89 Saab 9-5 Audio System Radio _______________ CD player ____________ CD changer ________ MP3 player ___________ Portable player _____ General functions _____ Sound system ________ Technical data ________ Antennas ____________ Error codes __________ Security lock _________ 93 99 100 102 104 105 107 108 109 112 112 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories). 95usM06.book Page 90 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 90 Saab 9-5 Audio System To get the best out of your Saab 9-5 Audio System, we recommend that you read through this entire section. The Saab 9-5 Audio System consists of a head unit with radio, CD player/CD changer for CD and MP3 discs and CD changer in the luggage compartment. The audio system is operated using the steering wheel controls or the control panel buttons. WARNING Safety first! Cut off power immediately and contact your Saab dealer if the system begins to emit smoke or smells strange. All work on the audio system must be carried out by a workshop. We recommend that you contact an authorized Saab dealer. Audio system activation/deactivation. Volume adjust. Information on artist, album and song title. Display of radio text. The tone control is used to adjust tone and speaker set- tings, change CD track or MP3 file and manual adjust radio frequency. Setup menu. 95usM06.book Page 91 Thursday, November 17, 2005 8:59 AM Scroll among preset pages. The menu option in the display is selected with the corre- sponding pushbutton directly underneath. No function on U.S./CA cars. Select XM program type when the radio is in the XM mode. Cars with CD changer : insert CD or MP3 disc or discs. Cars without CD-changer : set time and date. Eject CD or MP3 disc. Activate radio and change fre- quency band (AM,FM and XM ). Auto tuning down and change track/file going back in order of play on CD or MP3 disc. Auto tuning up and change track/file forward in order of play on CD or MP3 disc. Manual tuning and rapid play back for a track/file on a CD or MP3 disc. Manual tuning and rapid play forward for a track/file on a CD or MP3 disc. Activate CD media or portable player. Saab 9-5 Audio System Steering wheel controls 91 "arrow up"/"arrow down": change preset for radio stations, change track on CD or MP3 player. "Seek UP": auto tuning up, select next track on CD or MP3 disc. Activate radio station scan SRC: press to switch between AM, FM, XM , CD, MP3, CD changer or portable player. VOL: adjust volume. 95usM06.book Page 92 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 92 Switching the audio system On/Off The audio system will come on: (cid:127) When the ignition is switched ON and/or the ON/OFF control is pressed. ON/OFF control The audio system will be switched off: (cid:127) When the ON/OFF control is pressed. (cid:127) When the ignition key is removed. (cid:127) One hour after the ignition was switched OFF, if the ignition key has not been removed. (cid:127) 1 hour after the audio system has been switched on if the key is not in the ignition switch. Automatic tone setting You can choose to automatically adapt tone setting, (Equalizer), to the tuned station or disc being played. 1 Press the tone control to open the menu for tone settings. 2 Press the pushbutton under the menu option label. 3 Press the pushbutton under the desired tone setting. 4 The tone settings menu automatically returns to the previous menu within 5 seconds. Auto EQ menu Audio settings Volume Turn the ON/OFF control until the desired volume is obtained. Tone controls Tone and speaker settings Manual tone and speaker settings 1 Press the tone control to open the menu for tone and speaker settings. 2 Press the pushbutton under the desired tone/speaker setting. 3 Adjust the selected setting by turning the tone control. The selected settings can also be adjusted by pressing the SEEK, FWD or REV button. Centring tone and speaker settings Hold the tone control depressed until a chime sounds to centre all tone and speaker settings. 95usM06.book Page 93 Thursday, November 17, 2005 8:59 AM Radio Press the RADIO BAND button to return to radio mode if another audio source is in use. Selecting a radio station Selecting a frequency band Press the RADIO BAND button to change frequency band. The selected frequency band appears on the display. Selecting a preset station Scroll to the desired preset page by press- ing the FAV button and then pressing the pushbutton (1-6) under the desired preset station. You can also press "arrow up" or "arrow down" on the steering wheel to select another preset station. Saab 9-5 Audio System 93 Storing presets You can store up to 36 radio stations as pre- sets by using the 6 pushbuttons under the display and the FAV button. Press the FAV button to scroll through up to 6 pages with 6 presets per page. Each page can contain a combination of AM, FM and XM stations. Storing the current station as a preset To store the current station as a preset: 1 Press the FAV button until you come to the preset page (1-6) at which the sta- tion is to be stored. 2 Hold the pushbutton depressed under the spot (1-36) at which the station is to be stored. A chime will sound once the station is stored. Preset stations Tuning a station Fine tuning Turn the tone control one increment or press the REV or FWD button to fine-tune the frequency in increments of 0.2 MHz. Automatic tuning Press one of the SEEK buttons or the "Seek Up" button on the steering wheel for auto- matic seek tuning. The radio then searches upward in the frequency band for the near- est strong station and stops at that fre- quency. Manual tuning Turn the tone control or hold the REV or FWD button depressed to seek a frequency manually. Release the control/button to stop at the desired frequency. Scanning radio stations Hold one of the SEEK buttons or the "Seek Up" button on the steering wheel depressed until a chime sounds for a 5 second sam- pling of each station accessible on the fre- quency band. appears on the display. Press one of the SEEK buttons or the "Seek Up" button on the steering wheel again to cancel the scan and select the radio station being played at that instant. 95usM06.book Page 94 Thursday, November 17, 2005 8:59 AM 94 Saab 9-5 Audio System Number of pages with preset stations To display the number of pages (1-6) with preset stations: 1 Hold the FAV button depressed or press the MENU button and then press the pushbutton under the menu option . Setup menu 2 Select the number of preset pages to be displayed by pressing the pushbutton under the menu option with the desired number of preset pages (1-6). Number of preset pages Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: (cid:127) Display radio station name. (cid:127) Display messages from radio stations. (cid:127) This system relies on receiving specific information from these stations and will only work when the information is avail- able. In rare cased, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station. The RDS system is always on. When infor- mation is broadcast from the FM station you are listening to, the station name or call let- ters will be displayed on the display. Rolling advertisements Some radio stations present rolling adver- tisements in the display. (cid:127) To block rolling advertisements, mark by pressing the pushbutton directly underneath. (cid:127) To allow rolling advertisements, deselect by pressing the pushbutton directly underneath. Press the pushbutton under the arrow symbol or wait until the system automati- cally returns to the previous menu. Radio text Press the button to show text messages sent by certain radio stations in the display. If there are no text messages, appears on the display. RDS menu NOTICE The menu options AF and REG have no function on US/CA cars. 95usM06.book Page 95 Thursday, November 17, 2005 8:59 AM XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States. XM offers over 100 coast-to-coast chan- nels including music, news, sports, talk, and childrens programming. XM provides digital quality audio and text information, including song title and artist name. A service fee is required in order to receive the XM service. For more information, contact XM at www.xmradio.com or call 1-800-852-XMXM (9696). When XM is active, the channel name, and number, song title and artist will be dis- played. Saab 9-5 Audio System 95 Remove an XMTM category Undesired XM categories can be removed through the Setup menu. To remove an undesired category, perform the following: 1 Press the MENU button to display the radio Setup menu. 2 Press the pushbutton under the menu option . 3 Turn the tone control to display the cate- gory you wish to remove. 4 Press the pushbutton under the menu option until the category name along with the word appears on the display. 5 Repeat the steps to remove more cate- gories. Finding a XMTM station The PTY button is used to find XM stations when the radio is in the XM mode. To find XM channels within a desired category, perform the following: 1 Press the RADIO BAND button until the XM frequency is displayed. Press the PTY button to display the category labels on the radio display. Continue pressing the PTY button until the desired category name is displayed. 2 Press either of the two pushbuttons below the desired category label to immediately tune to the first XM sta- tion associated with that category. 3 Turn the tone control, press the buttons below the right or left arrows displayed, or press the right or left SEEK buttons to go to the next or previous XM station within the selected category. 4 To exit the category search mode, press the FAV button to display your favorites again. 95usM06.book Page 96 Thursday, November 17, 2005 8:59 AM 96 Saab 9-5 Audio System Restore removed XMTM categories Removed categories can be restored by pressing the pushbutton under the menu option when a removed category is dis- played or by pressing the pushbutton under the menu option . The XM Categories Decades Country Hits Christian Rock Urban Jazz & Blues Dance Latin World Classical Kids News Sports Comedy Talk & Variety Premium 95usM06.book Page 97 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 97 XM Radio Messages Radio Display Message Condition XM Updating Updating encryption code No XM signal Loss of signal Loading XM Channel Off Air Channel Unavail No Artist Info No Title Info No CAT Info Acquiring channel audio (after four second delay) Channel not in service Channel no longer available Artist Name/Feature not available Song/Program Title not available Category Name not available Action Required The encryption code in the receiver is being updated an no action is required. This process should take no longer than 30 seconds. The system is functioning correctly, but the vehicle is in a location that is blocking the XM signal. When you move into an open area, the signal should return. The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. This channel is not currently in service. Tune in to another channel. This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No artist information is available at this time on this channel. The system is work- ing properly. No song title information is available at this time on this channel. The system is working properly. No category information is available at this time on this channel. The system is working properly. 95usM06.book Page 98 Thursday, November 17, 2005 8:59 AM 98 Saab 9-5 Audio System Radio Display Message Condition Not Found No Information XM Theftlocked No channel available for the chosen category No Text/Informational message available Theft lock active XM Radion ID Radio ID label (channel 0) Unknown Check XM Receiver Radio ID not known (should only be if hardware failure) Hardware failure Action Required There are no channels available for the selected category. The system is working properly. No text or informational messages are available at this time on this channel. The system is working properly. The XM receiver in the vehicle may have previously been in another vehicle. For security purposes, XMreceivers cannot be swapped between vehicles. If this message is received after having your vehicle serviced, check with your Saab dealer. If tuned to channel 0, this message will alternate with the XM Radio eight digit radio ID label. This label is needed to activate the service. If this message is received when tuned to channel 0, there nay be a receiver fault. Consult with your Saab dealer. If this message does not clear within a short period of time, the receiver may have a fault. Consult with your Saab dealer. 95usM06.book Page 99 Thursday, November 17, 2005 8:59 AM CD player NOTICE Do not use CDs with labels or stickers. These labels could detach and cause the audio system to malfunction. Activate the CD player by inserting a disc or by pressing the CD AUX button if a CD is already loaded. CD player menu Loading CDs Insert the disc in the slot with the text side up until the mechanism loads the disc. The first track is played. If the disc is wrong-side-up, it will be ejected automati- cally. Once all the tracks have been played, the CD player will restart from track 1. The CD player is turned off by pressing ON/OFF to turn off the audio system or by selecting another audio source. Removing CDs Press the EJECT button to eject the CD. If you press EJECT without removing the ejected disc, the player will reload the disc after 10 seconds for reasons of safety. Selecting and changing tracks Turn the tone control or press the SEEK but- tons to select or change to the preceding or next track. The track number appears in the display. If the current track has played for at least 10 seconds, you can start the track from the beginning by pressing SEEK (arrow left). If you press SEEK (arrow right) while the last track of the disc is playing, the first track will play. If you press SEEK (arrow left) while the first track of the disc is playing, the last track will play. The same function applies to "arrow up" and "arrow down" on the steering wheel. Saab 9-5 Audio System 99 Rapid playing tracks To rapid play the current track, hold REV or FWD depressed. Release the button to stop rapid play and return to normal playback. Random playback You can allow the CD player to choose tracks randomly, i.e. not to play the tracks in numerical order. (cid:127) To play tracks randomly, press the push- button under the menu option . (cid:127) To resume playing tracks in numerical order, press the pushbutton under the menu option again. Random playback 95usM06.book Page 100 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 100 CD changer NOTICE Do not use CD or CD-R discs with labels or stickers. These labels could detach and cause the audio system to malfunc- tion. Activate the CD changer by inserting one or more CD/MP3 discs or by pressing the CD AUX button if one or more discs is already loaded. Loading CDs Loading a CD 1 Press the LOAD button. The following appears on the display: 2 Wait until the loading mechanism is ready for the disc. The following appears on the display: 3 Insert the disc in the slot with the text side up until the mechanism loads the disc. The following appears on the dis- play: If the disc is wrong-side-up, it will be ejected automatically. Loading several CDs The CD changer can be loaded with up to 6 discs. To load several discs in the CD changer: 1 Hold LOAD depressed for 2 seconds. A chime sounds and the following appears on the display: 2 Follow the instructions on the display to load the discs. 3 If you do not wish to load more CDs, press LOAD to cancel. CD changer menu The CD changer is turned off by pressing ON/OFF to turn off the audio system or by selecting another audio source. Removing CDs Removing a CD 1 Press EJECT to eject the disc. A chime sounds and the following appears on the display: 2 Remove the ejected disc when the fol- lowing appears on the display: If you press EJECT without removing the ejected disc, the player will reload the disc after 10 seconds for reasons of safety. Removing several CDs Hold EJECT depressed for 2 seconds to remove all discs from the CD changer. A chime sounds and the following appears on the display: 95usM06.book Page 101 Thursday, November 17, 2005 8:59 AM Selecting and changing tracks Turn the tone control or press the SEEK but- tons to select or change to the preceding or next track. The track number appears in the display. If the current track has played for at least 10 seconds, you can start the track from the beginning by pressing SEEK (arrow left). If you press SEEK (arrow right) while the last track of the disc is playing, the first track will play. If you press SEEK (arrow left) while the first track of the disc is playing, the last track will play. The same function applies to "arrow up" and "arrow down" on the steering wheel. For selecting/changing MP3 files, see page 102. Selecting/changing CD Press the pushbuttons under the menu option in the display to change CDs. For selecting/changing MP3 folder, see page 103. Selecting/changing CD Rapid playing tracks To rapid play the current track, hold REV or FWD depressed. Release the button to stop rapid play and return to normal playback. For rapid playing an MP3 file, see page 103. Saab 9-5 Audio System 101 Random playback You can allow the CD changer to choose tracks randomly from all CDs, i.e. not to play the tracks in numerical order. (cid:127) To play tracks randomly, press the push- button under the menu option . (cid:127) To resume playing tracks in numerical order, press the pushbutton under the menu option again. For random playback of MP3 files, see page 103. Random playback from all CDs 95usM06.book Page 102 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 102 MP3 player NOTICE Do not use CD-R discs with labels or stickers. These labels could detach and cause the audio system to malfunction. The audio system can play MP3 files recorded on an CD-R disc with the following bit speed: 32 - 320 kbps. Sound quality may vary depending on the quality of the CD-R disc, recording method and quality of the recorded music. The audio system can read and play a max- imum of 50 MP3 files, 50 playlists, 10 ses- sions and 255 MP3 files. Discs containing several folders, playlists, sessions and files can be played up to the max. limit. Anything over the max. limit will be ignored. Activating the MP3 player Activate the MP3 player by inserting a CD-R disc with MP3 files into the slot or by press- ing the CD AUX button if a disc with MP3 files is already loaded. The first file in the first playlist on the disc is played and the following appears on the dis- play: MP3 player Loading MP3 discs To load an MP3 disc, insert the disc in the slot with the text side up until the mecha- nism loads the disc. The first MP3 file in the first playlist of the disc will then be played. If the disc is wrong-side-up, it will be ejected automatically. For loading one or more MP3 discs in the CD changer, see page 100. Removing MP3 discs Press the EJECT button to eject the MP3 disc. If you press EJECT without removing the ejected disc, the player will reload the disc after 10 seconds for reasons of safety. For removing one or more MP3 discs from the CD changer, see page 100. Selecting/changing MP3 file Turn the tone control or press the SEEK but- tons to select or change to the preceding or next MP3 file in the current MP3 folder or playlist. The MP3 file number appears in the display. If the current MP3 file has played for at least 10 seconds, you can start the MP3 file from the beginning by pressing SEEK (arrow left). If you press SEEK (arrow right) while the last MP3 file in a folder or playlist is playing, the first MP3 file of the folder or playlist will play. If you press SEEK (arrow left) while the first MP3 file in a folder or playlist is playing, the last MP3 file of the folder or playlist will play. The same function applies to "arrow up" and "arrow down" on the steering wheel. 95usM06.book Page 103 Thursday, November 17, 2005 8:59 AM Playback order Files on a CD-R disc will be played in the fol- lowing order: (cid:127) The first MP3 file in the first playlist will be played, followed by all files in each playl- ist. When the last MP3 file in the last play- list has been played, playback starts from the beginning with the first MP3 file in the first playlist. (cid:127) The first MP3 file in the first MP3 folder will be played, followed by all files in each folder. When the last MP3 file in the last folder has been played, playback starts from the beginning with the first MP3 file in the first folder. Saab 9-5 Audio System 103 Sorting music To play MP3 files sorted by artist or album, press the pushbutton under the magnifying glass in the display. The CD player searches through the disc and sorts files by artist and album. This could take several minutes depending on the number of MP3 files on the disc. Once the sort is complete, select sort order by pressing the pushbutton under the menu option . (cid:127) To sort and play MP3 files by artist, press the pushbutton under the menu option . (cid:127) To sort and play MP3 files by album, press the pushbutton under the menu option . Selecting/changing MP3 folder (cid:127) Press the left pushbutton under the Folder symbol to play the first MP3 file in the pre- ceding MP3 folder on the disc. (cid:127) Press the right pushbutton under the Folder symbol to play the first MP3 file of the next MP3 folder on the disc. Rapid playing an MP3 file To rapid play the current MP3 file, hold REV or FWD depressed. Release the button to stop rapid play and return to normal play- back. Random playback of MP3 files You can allow the MP3 player to randomly select MP3 files, i.e. not to play the files in numerical order. (cid:127) For random playback of MP3 files, press the pushbutton under the menu option . (cid:127) To resume playing MP3 files in numerical order, press the pushbutton under the menu option again. Random playback of MP3 files 95usM06.book Page 104 Thursday, November 17, 2005 8:59 AM 104 Saab 9-5 Audio System Song title, artist name, etc. If a disc has been recorded with ID3 data (version 1 & 2), the song title, artist name, album title and MP3 folder name can be shown in the display. 1 Press the i button. 2 Press the pushbutton under the desired menu option. The song title, artist name, album title or MP3 folder name appears in the display. 3 Press the pushbutton under the arrow symbol to return to the previous menu. File names with more than 32 characters or four pages will be shortened. Information menu Portable player WARNING Place the portable player where it cannot be thrown around and cause personal injury in the event of a collision. AUX input The AUX input is located at the bottom right of the audio system. It can be used to con- nect a portable unit, such as an MP3 player, to the audio system. Adjust the sound settings using the control panel or the steering wheel controls. To change tracks, fast forward, etc., use the controls on the portable player. AUX input at the bottom right of the audio system Connecting and activating a portable player 1 Connect the unit to the audio system via the AUX input. 2 Press the CD AUX button to activate the portable player. 95usM06.book Page 105 Thursday, November 17, 2005 8:59 AM General functions WARNING Adjustments should be made when the car is stationary so that attention to traffic is not reduced, increasing the likelihood of an accident. Setting time and date Cars without CD changer 1 Press the Clock button. 2 Press the pushbutton under the menu option you wish to change. 3 Press the pushbutton again to increase time or date one increment at a time. You can also adjust time and date by press- ing the SEEK, FWD or REV button. Cars with CD changer 1 Press the MENU button. 2 Press the pushbutton under the clock symbol in the display. 3 Press the pushbutton under the menu option you wish to change. 4 Press the pushbutton again to increase time or date one increment at a time. You can also adjust time and date by press- ing the SEEK, FWD or REV button. Saab 9-5 Audio System 105 Time and date display 1 In the clock menu, press the pushbutton under the arrow symbol in the display. 2 Specify whether time should be dis- played with the 12-hour or 24-hour system and in which order date is to be indicated by pressing the pushbutton under the desired menu option. Setting time and date NOTICE Time and date display The menu option RDS has no function on US/CA cars. 95usM06.book Page 106 Thursday, November 17, 2005 8:59 AM 106 Saab 9-5 Audio System Speed dependent volume compensation As vehicle speed increases, ambient noise also increases. If you do not wish to contin- ually adjust the volume, the audio system can automatically adjust volume based on an increase or decrease in vehicle speed. Select one of four settings: (cid:127) (no compensation) (cid:127) !" (low compensation) (cid:127) (medium compensation) (cid:127) #$% (maximum compensation) 1 Press the MENU button. 2 Press the pushbutton under the menu option & !&. 3 Press the pushbutton under the desired speed compensation. Speed dependent volume compensation 95usM06.book Page 107 Thursday, November 17, 2005 8:59 AM Sound system The sound system is called Prestige. Loud- ness is controlled automatically by the audio system, boosting the highest and lowest fre- quency ranges to enhance the sound image when the volume is set to a low level. Sound reproduction is therefore excellent what- ever the volume setting. The 9-5 SportCombi has 8 speakers as there is only one subwoofer in the luggage compartment. Prestige The Prestige system has 9 speakers: three mounted in the instrument panel fascia (the centre speaker further enhances the sound image), one in each door and two subwoof- ers in the parcel shaft. The subwoofers enhance reproduction of the lowest bass notes. Saab 9-5 Audio System 107 95usM06.book Page 108 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 108 Technical data Tone controls Bass_____________ ±8 dB at 100 Hz Treble ____________ ±8 dB at 16 kHz Power output Prestige ________ 200 W 150 W at 1% THD and 13.5 V Radio module Radio system ______ PLL frequency syn- thesizer tuner. Number of presets FM/AM/XM __ 6 x 6 Frequency range FM ____________ 87.7 - 107,9 MHz AM ____________ 530 - 1710 kHz Tuning steps Automatic tuning __ FM 200 kHz AM 10 kHz Manual tuning ____ FM 200 kHz AM 10 kHz Frequency range (FM) 40 – 11000 Hz ±1 dB Distortion (FM) _____ < 0.5% CD player and CD changer 1-bit system and 8 x oversampling Frequency range ___ 20 – 20000 Hz ±1 dB Distortion _________ <0.005% Dynamics _________ >85 dB CD changer capacity: 6 discs Specifications in accordance with EIA Interim Standard. THD = Total Harmonic Distortion 95usM06.book Page 109 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 109 Antennas The audio system has two antennas incor- porated in either the rear window or the windscreen: one for FM and one for AM. The XM Satellite Radio antenna is located on the roof of the vehicle. Keep this antenna clear of snow and ice build up for clear radio reception. (cid:127) Roof loads can negatively affect telecom- munication, GPS reception and the per- formance of the XM system . If sun film is fitted to the rear window, it must be a pure-plastic variety to maintain good radio reception. Ensure that the film does not contain any metal. NOTICE Refrain from placing hard or sharp objects on the rear parcel shelf, to avoid damaging the antenna leads. Multipath propagation Multipath propagation occurs when radio waves from an FM transmitter are reflected by a large building, or the like, causing them to arrive slightly later than the direct waves. This can create interference to radio recep- tion. See also "Diversity antenna". Diversity antenna To improve radio reception when the topog- raphy is a problem, a second FM antenna, known as a diversity antenna, can be fitted in the rear window. Consult a Saab dealer for further information. (cid:127) 95usM06.book Page 110 Thursday, November 17, 2005 8:59 AM 110 Saab 9-5 Audio System FM AM Shadow effect Because FM radio waves travel in straight lines from the transmitter, a shadow effect can occur when tall buildings or hills obstruct the propagation path from the transmitter to the car. Cross modulation If the radio is tuned to a weak transmitter in the vicinity of a stronger one, the car’s antennas will receive signals from both. Such interference is apparent when the unwanted broadcast can be heard faintly in the background. Radio waves, FM/AM FM radio waves radiate in straight lines from the transmitter. Because such waves do not follow the curvature of the Earth, their strength becomes weaker the further they travel. That is why a large number of trans- mitters is needed to provide good reception. AM waves, on the other hand, are reflected off the ionosphere, thus greatly extending their range. 95usM06.book Page 111 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 111 Sources of FM interference Interference to FM reception can be caused by the electrical systems in other vehicles, particularly if the signal from the transmitter is weak. Sources of AM interference AM reception is prone to interference, e.g. from electrical systems in other vehicles, high-tension power lines and lightning. 95usM06.book Page 112 Thursday, November 17, 2005 8:59 AM Saab 9-5 Audio System 112 Error codes NOTICE Proceed with care if rectifying a fault. If in doubt, contact a workshop. We recom- mend that you contact an authorized Saab dealer. The audio system has a built-in diagnostics function. If a fault is detected, a error code is generated to help workshop technicians to diagnose the fault. Below are the codes for some faults that you might be able to rec- tify yourself. Error code Check CD Possible cause (cid:127) CD is dirty, scratched, loaded wrong-side-up or defective. (cid:127) The CD may be improperly burned. Security lock The audio system is equipped with an elec- tronic security lock. The special code is unique to the car in which the audio system is fitted. Each time the audio system is switched on, a check is made to ensure that the code is correct. If not, the following will appear on the display: If the audio system is to be transferred to another car (Saab 9-5), a Saab dealer must be contacted to provide the right code for the audio system. WARNING The CD player/CD changer is classified as Class 1 laser equipment. (cid:127) Service and repair work must only be carried out by authorized technicians. (cid:127) If the casing is damaged, hazardous laser radiation can occur. NOTICE All work on the audio system must be car- ried out by a workshop. We recommend that you contact an authorized Saab dealer. 95usM06.book Page 113 Thursday, November 17, 2005 8:59 AM Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories). Interior equipment and trunk 113 Interior equipment and trunk Steering wheel adjustment__________ Electric windows______ Rearview mirrors______ Moonroof __________ Interior lighting _______ Sun visors ___________ Ashtrays ___________ Glove compartment ___ Cup holders __________ Trunk _______________ 114 115 116 123 124 125 126 127 129 130 95usM06.book Page 114 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 114 Steering wheel adjustment WARNING Never adjust the steering wheel unless the car is stationary. Fore-and-aft and tilt adjustment of the steer- ing wheel is possible. Pull down the lever fully until you hear a click. Move the steering wheel to the desired position and then raise the lever. The lever should lock with a click. Make sure that the lever is fully locked before driving off. To adjust the steering wheel Horn The horn is sounded by pressing the central part of the steering wheel. Press closest to the steering wheel rim. 95usM06.book Page 115 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 115 Electric windows WARNING Bear in mind the pinch hazard when the side windows are being wound up. (cid:127) Always remove the ignition key when you leave the car. This prevents per- sonal injury caused by the electric win- dows, for example, due to children playing. (cid:127) The person operating the electric win- dows is responsible for ensuring that no one, especially children, has their head, hands or fingers in the window openings, before raising the windows. Raising the windows could otherwise cause serious or fatal injuries. (cid:127) Do not extend your arm, head etc. out of an open window while driving. The electric motors of the front windows are equipped with overload protection (inte- grated thermal protection). This protection operates when the windows are wound down automatically (switch pressed fully down). 1 Window switches 2 Switch for rendering rear door window switches inoperative To open: Front windows: press the front of the switch Rear windows: Press the back of the switch. The switches for the front windows have a third position for automatic opening of the window. Press the switch fully down to lower the window completely. To cancel automatic lowering of the win- dow, lift the switch briefly. To close: Front windows: Lift the front of the switch. Rear windows: Lift the back of the switch. The actuating motor will be switched off automatically when the window is fully closed or when the switch is released. 95usM06.book Page 116 Thursday, November 17, 2005 8:59 AM 116 Interior equipment and trunk Child safety: rear windows (ON/OFF) The window switches on the rear doors can be rendered inoperative by the ON/OFF switch in the panel on the center console. When the switch is ON, the rear side win- dows can be operated by the switch on each rear door. The switch’s back lighting will be activated. When the switch is OFF, the rear side win- dows can only be operated from the panel on the center console. When off, the switch’s back lighting will also be switched off. Switch for rear side window Adjusting the door mirrors 1 Select mirror 2 Use touch pad to adjust mirror Rearview mirrors Door mirrors The door mirrors may have an auto dimming function and the passenger side door mirror is of the wide-angle ‘‘aspheric” type. The door mirrors are designed to fold back if knocked. They can also be fully retracted for parking in tight spaces, such as on the car deck of a ferry. Remember to fold them out again before driving off. NOTICE The door mirrors should be fully retracted before the car enters an automatic car wash. 95usM06.book Page 117 Thursday, November 17, 2005 8:59 AM The adjusting switch is on the driver’s door. If the car is equipped with a programmable driver’s seat, the settings of the door mirrors can also be stored in the preset buttons for the seat (see page 20). Cars equipped with a programmable driver’s seat also have the ability to angle the passenger’s mirror down when revers- ing, e.g. for a better view of the curb. 1 Select reverse. 2 Press the tiny button adjacent to the doormirror switch to tilt the mirror. The mirror will be reset automatically when reverse gear is deselected. The mirror glass can also be adjusted man- ually by gently pressing the glass in the desired direction. The mirrors are heated, and the heating comes on and goes off with the rear-window heater. Interior equipment and trunk 117 Door mirror folded in Button for angling passenger’s mirror down when reversing 95usM06.book Page 118 Thursday, November 17, 2005 8:59 AM 118 Interior equipment and trunk Rearview mirror 1 Day position 2 Night position Rearview mirror The rearview mirror has day/night positions that can be selected by means of a knob beneath the mirror. Adjust the mirror in day position. Interior rearview auto-dimming mirror with garage door opener, and digital compass WARNING Make sure that people and objects are out of the way of a moving door or gate to pre- vent potential harm or damage. When programming the garage opener, you may be operating a garage door or gate operator. Therefore it is advised to park outside of the garage. Do not use the garage opener with any garage door opener that lacks the safety stop and reverse feature as required by federal safety standards. (This includes any garage door opener model manufac- tured before April 1, 1982.). A garage door opener which cannot detect an object, signalling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases risk of serious injury or death. Retain your original garage door transmitter for future programming procedures (i.e., new vehicle purchase). It is also suggested that upon the sale of the vehicle, the pro- grammed garage opener buttons be erased for security purposes. Buttons for garage opener and compass 1-3 Garage opener 4 LED 5 Compass/auto dimming ON/OFF 6 Compass bearing 95usM06.book Page 119 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 119 antenna wire is attached to the motor-head unit. 8 Firmly press and release the "learn" or "smart" button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to ini- tiate step nine. 9 Return to the vehicle and firmly press, hold for two seconds and release the programmed button. Repeat the "press/hold/release" sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to com- plete the programming process. The garage opener should now activate your rolling code equipped device. Note: To program the remaining two but- tons, begin with "Programming" - step three. Do not repeat step two. Preparations for first-time programming Before programming the garage opener for the first time, you must delete any factory codes. Press and hold the two outer buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. The garage opener is now in the train (or learning) mode and can be programmed at any time begin- ning with "Programming" - step 2. Programming The garage opener can record and store the frequencies of three different remote con- trols. The battery in the remote control should be fairly new for programming to work well. Do not repeat "Programming" - step two to train additional devices to a second or third button. Begin with "Programming" - step three. 1 Turn the ignition ON. 2 Press and hold the two outer buttons (buttons one and three) - releasing only when the indicator light begins to flash (after 20 seconds). Do not hold the but- tons for longer than 30 seconds and do not repeat step two to program a second and/or third hand-held transmit- ter to the remaining two buttons. 3 Position the end of your hand-held trans- mitter 1-3 inches (5-14 cm) away from the button you wish to program while keeping the indicator light in view. The transmitter should face the mirror from below or left side of the mirror. 4 Simultaneously press and hold both the chosen and hand-held transmitter but- tons. Do not release the buttons until step 5 has been completed. Note: Some gate operators and garage door openers may require you to replace this Programming Step 4 with procedures noted in the "Gate Operator / Canadian Pro- gramming" section. 5 After the indicator light changes from a slow to a rapidly blinking light, release both the mirror and hand-held transmit- ter buttons. 6 Press and hold the just-trained button and observe the indicator light. If the indicator light stays on con- stantly, programming is complete and your device should activate when the button is pressed and released. Note: To program the remaining two but- tons, begin with "Programming" - step three. Do not repeat step two. If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with "Programming" steps 7-9 to complete the programming of a rolling code equipped device (most com- monly a garage door opener). 7 At the garage door opener receiver (motor-head unit) in the garage, locate the "learn" or "smart" button. This can usually be found where the hanging 95usM06.book Page 120 Thursday, November 17, 2005 8:59 AM 120 Interior equipment and trunk Reprogramming a single button To program a device to the garage opener using a button previously trained, follow these steps: 1 Press and hold the desired button. DO NOT release the button. 2 The indicator light will begin to flash after 20 seconds. Without releasing the but- ton, proceed with "Programming" - step 3. Erasing the three buttons To erase programming from the three but- tons (individual buttons cannot be erased but can be "reprogrammed" as outlined below), follow the step noted: (cid:127) Press and hold the two outer buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. The garage opener is now in the train (or learn- ing) mode and can be programmed at any time beginning with "Programming" - step 3. Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter signals to "time-out" (or quit) after several seconds of transmission - which may not be long enough for the garage opener to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to "time-out" in the same manner. If you live in Canada or you are having diffi- culties programming a gate operator by using the "Programming" procedures (regardless of where you live), replace "Programming " step 4 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the "cycling" process to pre- vent possible overheating. Continue to press and hold the button while you press and release - every two sec- onds ("cycle") your hand-held transmitter until the frequency signal has successfully been accepted by the garage opener. (The indicator light will flash slowly and then rap- idly.) Proceed with "Programming" step five to complete. NOTICE Switch off the power supply to the garage door or gate (or park the car beyond the range of the remote control) while pro- gramming using the "cycling" method to prevent damaging the electrical motor. 95usM06.book Page 121 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 121 Opening a garage door To operate, simply press and release the programmed button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. NOTICE Switch off the power supply to the garage door or gate (or park the car beyond the range of the remote control) while pro- gramming using the "cycling" method to prevent damaging the electrical motor. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) must accept any interference received, including inter- ference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interfer- ence that may cause undesired operation of this device. Rearview auto-dimming mirrors The autodimming is activated and deacti- vated with a short push on button 2. If the mirror is equipped with Garage Door Opener (option) the letter 1 is displayed on compass bearing display briefly when auto dimming is activated. When deactivating the letter 0 is displayed. The interior rearview mirror has two sen- sors, one forward-facing and one rear-fac- ing. They also activate and deactivate the auto dimming feature on door mirrors. The system is activated when the for- ward-facing sensor detects that it is dark outside and the rear-facing sensor detects. For example, if the car following has not dimmed its headlights. The rearview mirrors are then darkened to prevent the strong light source from dazzling the driver. This dark- ening is stepless. The mirrors return to their normal states when the strong light source diminishes. The auto dimming function can be turned OFF with the switch on the lower edge of the rear-view mirror. NOTE Towing a trailer can cause the system to malfunction, as the rear-facing sensor may sense light from the trailer. 1 Forward-facing sensor 2 ON/OFF switch, auto dimming function 3 Rear-facing sensor 95usM06.book Page 122 Thursday, November 17, 2005 8:59 AM 122 Interior equipment and trunk Compass The compass is integrated in the rearview mirror. The compass bearing is displayed in the top right-hand corner of the mirror and is updated every other second. The compass displays the car’s direction of travel: N, NE, E, etc. Switch the compass display on and off by pressing button 5 for 3 seconds. Compass zones in Canada Compass zones in US Changing zones The earth’s magnetic fields vary depending on one’s position on the globe. If you drive your car from one magnetic zone to another the compass setting will need to be changed to ensure a correct bearing. 1 Study the illustrations to determine the correct zone. 2 Press and hold button 5 until "ZONE" is shown in the display on the mirror (6 seconds). The zone number setting now is also shown. 3 Press button 5 repeatedly to change the zone number. There are 15 zones from which to choose. Once the correct zone is selected, release the button and wait 4 seconds. The compass will now dis- play the bearing. Calibration Calibration is performed automatically during travel. If an accessory, such as a mobile phone, is fitted and it can be assumed that the compass is affected, the compass may need to be calibrated manu- ally. 1 Press and hold button 5 until "CAL" and the compass bearing are displayed (approx. 9 seconds). 2 Drive in circles (max. 5 mph/8 km/h) or drive as normal until "CAL" is no longer displayed. 95usM06.book Page 123 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 123 Moonroof WARNING Bear in mind the pinch hazard when clos- ing the moonroof. (cid:127) Always remove the ignition key when you leave the car. This prevents per- sonal injury caused by the electric moonroof, for example, due to chil- dren playing. (cid:127) The person operating the electric moonroof is responsible for ensuring that no one, especially children, has their head, hands or fingers in the opening, before closing the moonroof. Operating the moonroof could other- wise cause serious or fatal injuries. (cid:127) Do not extend your arm, head etc. out of an open moonroof while driving. The moonroof is operated by the switch on the overhead panel above the rearview mir- ror. The moonroof can be opened partially or fully. To open: (cid:127) Slide the control towards the rear to open the moonroof to the comfort position. To open it fully, slide the control back a second time. Press the control to stop it earlier. To close: (cid:127) Slide the control forwards until the moon- roof is closed. Ventilation position (cid:127) Press the middle of the control (when moonroof closed). (cid:127) To close: slide the control forwards. To fully open the moonroof from the ventila- tion position, slide the control back. The moonroof incorporates an interior, manual, sliding sun blind. If the car is newly waxed, the moonroof may creak when opened to the ventilation posi- tion or when driving with the moonroof closed. The sound comes from the area where the front edge of the moonroof meets moonroof control 1 To open 2 To close 3 Ventilation position the metal roof. Open the moonroof fully and, using washer fluid, clean the seal on the leading edge of the moonroof and the painted surface against which this seals when the moonroof is closed. 95usM06.book Page 124 Thursday, November 17, 2005 8:59 AM 124 Interior equipment and trunk Manual operation of moonroof Emergency operation of moonroof In an emergency (e.g. if there is an electrical failure) the moonroof can be operated by a screwdriver. Remove the cover at the front of the moonroof opening, insert a screw- driver in the groove, and rotate. Rotate counterclockwise to close moonroof. 1 Interior lighting on continuously 2 Lighting comes on when a door is opened 3 Lighting always off Interior lighting The interior lighting consists of one dome light in the front and one in the back, a map-reading light in the front, two reading lights in the back, floor courtesy lights in the front (in some model variants) and door courtesy lights on all doors. The courtesy lights come on automatically when the respective door is opened. Each reading light has its own switch adjacent to the lamp. The switch for the dome lights is on the front overhead panel. When the switch is in the mid-position (door-activated), the interior lighting will come on: (cid:127) When the car is unlocked from the out- side. (cid:127) When any door is opened. (cid:127) When the ignition key is withdrawn from the ignition switch. Lighting goes out 30 seconds after the doors have been closed or: (cid:127) when the ignition is switched ON, pro- vided that the cabin lighting control is in the centre position (cid:127) when the car is locked with the remote control. 95usM06.book Page 125 Thursday, November 17, 2005 8:59 AM 1 Reading lights 2 Dome light There is also a light in the sun visors. The light comes on when the cover over the vanity mirror is opened. When the ignition is OFF, if a door has been left open for 20 minutes, the interior lighting will be switched off automatically to save the battery. Interior equipment and trunk 125 Luggage-compartment lighting The luggage-compartment lighting comes on automatically when the trunk is opened and goes out when the trunk is closed. The lighting will also be switched off auto- matically after 20 minutes if the trunk has been left open. Sun visor Sun visors The car is equipped with double sun visors. One section of the visor can be indepen- dently pivoted to the side window. A vanity mirror is provided on the back of the sun visors. The vanity mirrors are illumi- nated when the cover is raised. Cigarette lighters The car is provided with cigarette lighters next to the front ashtray and in the rear end of the center console. The cigarette lighter sockets can also be used for accessories (e.g. to charge a mobile phone) when the ignition is ON. WARNING The maximum combined load for the two cigarette lighter sockets is 240 W (20 A). 95usM06.book Page 126 Thursday, November 17, 2005 8:59 AM Interior equipment and trunk 126 Ashtrays The car can be equipped with three ash- trays: one in the instrument panel fascia, and one in each rear door. A cigarette lighter is fitted adjacent to the front ashtray, and there is also one in the back of the center console. Front ashtray 1 To open the ashtray, push gently on the center/upper part of the front and release to allow it to spring out. 2 Close the ashtray in the same way. To remove the ashtray, open it and after that pull left side out at an angle. To refit, line up the slots on either side and slide it closed. Rear ashtrays Open the lid to use ashtray. To remove the ashtray, fully open the lid and lift the ashtray straight out. To refit the ashtray, make sure it engages the two square recesses in the door trim. Front ashtray 1 Press soft to open/close 2 Pull out one side at an angle Rear ashtray 95usM06.book Page 127 Thursday, November 17, 2005 8:59 AM Glove compartment WARNING The glove compartment must be closed while travelling. An open glove compart- ment door could cause leg injuries in the event of a crash. The glove compartment can be cooled by the air conditioning (ACC) system. Cold air can be directed to the glove compartment for keeping drinks cool, etc. Slide the cover to open/close the air inlet. Additional storage facilities are provided (see next page). Interior equipment and trunk 127

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Saab 9 5 Owners Manual