2010 Pontiac VIBE Owners Manual

Download PDF Manual
For example, the gage may have indicated the tank was half full, but it actually took more or less than half the tank’s capacity to ﬁll it. It takes the gage several minutes to read F or full after ﬁlling the vehicle with fuel. • • Instruments and Controls 4-11 • The gage moves a little when you turn, stop or speed up. • The gage does not go back to E or empty when you turn off the ignition. Engine Coolant Temperature Gage Safety Belt Reminders When the engine is started, a chime will sound for several seconds to remind people to fasten their safety belts, unless the driver safety belt is already buckled. Canada United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, the engine is too hot. Pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating on page 9-23. The safety belt light will also ﬂash until the driver belt is buckled. If the driver belt is already buckled, neither the chime nor the light comes on. This light is located on the center of the instrument panel, next to the audio system. When the key is turned to ON/RUN or START, this light comes on as a reminder for the right front passenger to fasten their safety belt. 4-12 Instruments and Controls This light ﬂashes until the right front passenger safety belt is buckled. The passenger safety belt reminder light will not come on if the right front passenger belt is already buckled or if a sensor does not detect the weight of a passenger in that seat. If something is placed on the right front passenger seat, the sensors in the seat may detect that object and cause the right front passenger safety belt reminder light to come on. If this happens, remove the object. Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 2-23. The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out. If it stays on after the vehicle has been started or comes on when while driving, the airbag system may not work properly. Have the vehicle serviced right away. { CAUTION If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury, have the vehicle serviced right away. Instruments and Controls 4-13 Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 2-29 for important safety information. The instrument panel has a passenger airbag status indicator. When the vehicle is started, the passenger airbag status indicator will light ON and OFF for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF if there is weight on the seat, to let you know the status of the right front passenger frontal and seat-mounted side impact airbags (if equipped). If the seat is unoccupied, the light will not be visible after the system check. If the word ON is lit on the passenger airbag status indicator, it means that the right front passenger frontal and seat-mounted side impact airbags (if equipped) are enabled (may inﬂate). If the word OFF is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped). See Passenger Sensing System on page 2-29 for more on this, including important safety information. If, after several seconds, all status indicator lights remain on, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { CAUTION If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 4-12 for more information, including important safety information. 4-14 Instruments and Controls Charging System Light The charging system light comes on brieﬂy when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer/retailer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner. Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. Canada United States This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/ retailer. If the check engine light comes on and stays on, when the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. If the vehicle is Instruments and Controls 4-15 Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 9-3. This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. The following can prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. • If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still ﬂashing, follow the previous steps and see your dealer/ retailer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: • Make sure the fuel cap is fully installed. See Filling the Tank on page 8-41. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. • 4-16 Instruments and Controls • Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Fuel on page 8-38. If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in the ON/RUN and the light is not on. • The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/ retailer can prepare the vehicle for inspection. Instruments and Controls 4-17 Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working well. If the warning light comes on, there is a brake problem. Have the brake system inspected right away. Canada United States If the vehicle has anti-lock brakes, this light should come on when the key is turned to START. If it does not come on, have it ﬁxed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light will stay on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means there is a brake problem. { CAUTION The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. See Antilock Brake System (ABS) Warning Light later in this section and Antilock Brake System (ABS) Warning Light on page 4-17. Antilock Brake System (ABS) Warning Light United States Canada The ABS warning light comes on brieﬂy when the ignition key is turned to ON/RUN. This is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the light stays on, turn the ignition to LOCK/OFF. If the light comes on while driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, there are still brakes, but no antilock brakes. 4-18 Instruments and Controls If the regular brake system warning light is also on, there are no antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 4-17. Service All-Wheel Drive Light This light will come on brieﬂy when the ignition is turned on, and the engine is not running, as a check to show you it is working. It should go out when the engine is started. It should go out when the engine is started. If it stays on, or comes on while you are driving, you may have a problem with the system. Have it checked by your dealer/ retailer. The four-wheel-drive indicator will light up when the All-Wheel drive is active. Speed Sensitive Power Steering (SSPS) Warning Light StabiliTrak® Indicator Light Vehicles with this feature, have a warning light that comes on brieﬂy when the ignition is turned to ON/RUN as a check to show it is working. If the warning light does not come on, have it ﬁxed so it will be able to warn if there is a problem. If the warning light stays on, or comes on while driving, the Speed Sensitive Power Steering may not be working. See your dealer/retailer for service. This light warns that there is a problem with the Traction Control System (TCS) or the Vehicle Stability Control (VSC) system. The light comes on when the ignition is turned to ON/RUN. If the light comes on while driving, the system is not working. The TCS light comes on when the VSC system warning light comes on, even if the TRAC OFF button is not pressed. See StabiliTrak System on page 8-35 for more information on Vehicle Stability Control System. Instruments and Controls 4-19 See Traction Control System (TCS) on page 8-33 for more information. Contact your dealer/retailer, if the light does not come on or if it stays on. Traction Control System (TCS) Warning Light If it stays on or comes on while driving, there is a problem with the Traction Control System (TCS), contact your dealer/retailer. Tire Pressure Light This warning light comes on brieﬂy when the ignition is turned to ON/RUN. It also comes on when the Traction Control System is turned off by pressing the TRAC OFF button. See Traction Control System (TCS) on page 8-33 for more information. This light should come on brieﬂy as the engine is started. If there is a tire with low tire pressure, the light will stay on or come back on. See Tire Pressure Monitor Operation on page 9-52 for more information. Engine Oil Pressure Light { CAUTION Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil. The oil pressure light should come on brieﬂy as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. 4-20 Instruments and Controls If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly. The vehicle could be low on oil and might have some other system problem. Low Fuel Warning Light Canada United States This light, on the fuel gage, comes on when the fuel tank is low on fuel. To turn if off, add fuel to the fuel tank. Security Light Fog Lamp Light For information regarding this light and the vehicle’s security system, see Vehicle Security on page 1-7. High-Beam on Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 5-4 for more information. Lamps on Reminder The highbeam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 5-2 for more information. This light comes on whenever the headlights are on. See Exterior Lamp Controls on page 5-1 for more information. Instruments and Controls 4-21 Taillamp Indicator Light Cruise Control Light Canada Only This light comes on when the taillamps are on. See Exterior Lamp Controls on page 5-1 for more information. Low Washer Fluid Warning Light The CRUISE light comes on when the cruise control is on. See Cruise Control on page 8-36 for more information. Door Ajar Light Canada Only This light comes on when the windshield washer ﬂuid is low. See Washer Fluid on page 9-24 for more information. This light comes on if any door, the rear liftgate, or the rear liftglass are not completely closed. Vehicle Personalization Your vehicle may have lighting and door lock features that can be programmed to your preference. You will need to schedule an appointment with your dealer/ retailer if you would like to change the way these features are currently programmed. The following is a list of the features that can be programmed. See your dealer/ retailer to change the programming of these features: Driver Door Key Unlock Switch: If this feature is programmed on, all of the doors will unlock when the key is turned twice in the driver’s door lock cylinder. When the vehicle left the factory this feature was programmed on. 4-22 Instruments and Controls Courtesy Lamp Timer: This feature allows for changing how long the courtesy lamps stay on when all the doors and liftgate are closed and the key is out of the ignition, in LOCK/OFF, or in ACC/ACCESSORY. When the vehicle left the factory the courtesy lamps were programmed to stay on for 15 seconds. This can be changed to 7.5 seconds or 30 seconds. Interior Lamps when Ignition off: If this feature is programmed on, the interior lamps will come on when the ignition is turned off when it is dark outside. When the vehicle left the factory this feature was programmed on. Interior Lamps on with Door Key Unlock: If this feature is programmed on, the interior lamps will come on when the doors are unlocked when it is dark outside. When the vehicle left the factory this feature was programmed on. Key Fob Signal: If this feature is programmed on, the Remote Keyless Entry (RKE) transmitter can be used to lock and unlock the vehicle. When the vehicle left the factory this feature was programmed on. RFA Visual Feedback: If this feature is programmed on, the hazard lights will ﬂash when you lock and unlock the vehicle with the RKE transmitter. When the vehicle left the factory this feature was programmed on. RFA All Unlock Enable: If this feature is programmed on, pressing the RKE unlock button twice within three second will unlock all of the doors. When the vehicle left the factory this feature was programmed on. Remote Panic Command: If this feature is programmed on, pressing and holding the RKE panic button will cause the horn to sound and the lights to ﬂash. When the vehicle left the factory this feature was programmed on. Automatic Door Locking: If this feature is programmed on, the doors will automatically lock when the vehicle is shifted out of P (Park) or when the vehicle speed is greater than 8 mph (13 km/h). Automatic Door Unlocking: If this feature is programmed on, the doors will automatically unlock when the vehicle is shifted into P (Park) or when the ignition is turned off. All Door Unlock Command: If this feature is programmed on, the doors will all unlock when the driver’s door is opened. Lock-out Timer: This feature allows for changing how long of a delay there is before all of the doors lock when pressing the lock button on the RKE transmitter. When the vehicle left the factory the delay was set for 1 minute. This can be changed to 30 seconds or 2 minutes. OnStar System OnStar® System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If the keys are locked in the vehicle, call OnStar at 1-888-4-ONSTAR to have a Instruments and Controls 4-23 signal sent to unlock the doors. OnStar Hands-Free Calling, including 30 trial minutes good for 60 days, is available on most vehicles. Press the OnStar button to have an OnStar advisor contact Roadside Service. OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the ﬁrst prepaid year, contact OnStar to select a monthly or annual subscription payment plan. If a payment plan is not selected, the OnStar system and all services, including airbag notiﬁcation and emergency services, may be deactivated and no longer available. For more information visit www.onstar.com (U.S.) or www.onstar.ca (Canada), or press the OnStar button to speak with an advisor. Not all OnStar services are available on all vehicles. To check if this vehicle is able to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in the glove box or visit www.onstar.com (U.S.) or www.onstar.ca (Canada), contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. 4-24 Instruments and Controls OnStar Services Available with the Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert • OnStar Hands-Free Calling with 30 trial minutes • OnStar Virtual Advisor (U.S. Only) OnStar Services Included with Directions & Connections Plan • All Safe and Sound Plan Services • Driving Directions - Advisor Delivered • RideAssist • Information and Convenience Services OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days. Hands-Free Calling can also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information. This feature is only available in the continental U.S. How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags deploy. This information usually includes the vehicles GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). Instruments and Controls 4-25 When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicles GPS location so they can provide services where it is located. OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless the vehicle is in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place. Some examples are damage to important parts of the vehicle in a crash, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly. If the light appears clear (no light is appearing), your OnStar subscription has expired and all services have been deactivated. Press the OnStar button to conﬁrm that the OnStar equipment is active. 4-26 Instruments and Controls ✍ NOTES Lighting Exterior Lighting Exterior Lamp Controls Exterior Lighting Exterior Lamp Controls ...........5-1 Headlamp High/Low-Beam Changer .............................5-2 Flash-to-Pass ........................5-2 Daytime Running Lamps (DRL) ......................5-2 Automatic Headlamp System ..............................5-3 Hazard Warning Flashers .......5-3 Turn and Lane-Change Signals ...............................5-3 Fog Lamps ...........................5-4 Interior Lighting Instrument Panel Illumination Control ...............................5-4 Dome Lamps ........................5-4 Reading Lamps .....................5-5 Lighting Features Entry Lighting .......................5-5 Battery Power Protection ........5-5 The lever on the left side of the steering column operates the exterior lamps. P / ; (Exterior Lamps): Turn the outside band of the lever to operate the lamps. For vehicles sold in the U.S., P appears on the instrument Lighting 5-1 panel cluster when the exterior lamps are on. For vehicles ﬁrst sold in Canada, ; appears in the instrument panel cluster. See Lamps on Reminder on page 4-20. The exterior lamp switch has three positions: ( (Off): Turns off all lamps, except the Daytime Running Lamps (DRL). ; (Parking Lamps): Turns on the parking lamps together with the following: • Sidemarker Lamps • Taillamps • License Plate Lamp • 5 (Headlamps): Turns on the headlamps, together with the previously listed lamps and lights. Instrument Panel Lights 5-2 Lighting Headlamps on Reminder A tone sounds when the ignition is turned to LOCK/OFF, the driver door is opened and the key is removed from the ignition while the lamps are on. Headlamp High/ Low-Beam Changer The headlamps must be on for this feature to work. Push the turn signal lever away from you to turn the high beams on. This instrument panel cluster light 3 comes on while the high beam headlamps are on. Pull the lever towards you to return to low beams. Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. With the lever in the low-beam position, pull the lever toward you to momentarily switch to high-beams. If the headlamps are on when the lever is released, the high-beams will return to low-beam. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles ﬁrst sold in Canada. The DRL system makes the headlamps come on at a reduced brightness when the following conditions are met: • The ignition is on with the engine running. • The exterior lamps switch is off. • The parking brake is released. When the exterior lamp switch is turned to the headlamp position, the DRL go off and the headlamps come on. The other lamps that come on with the headlamps also come on. The headlamps automatically switch from DRL to the regular headlamps depending on the darkness of the surroundings. See Automatic Headlamp System on page 5-3. DRL also comes on if only the parking lamps are being used. Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the low-beam headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps and instrument panel lights. An indicator light on the instrument panel comes on when the headlamps are on. See Instrument Cluster on page 4-9. If the vehicle is driven through a parking garage, overcast weather, or a tunnel, the automatic headlamp system may turn on. There is a delay before the lights turn on when starting the car at night. Do not cover the automatic light sensor, located on the top left corner of the instrument panel. If the sensor is covered the headlamps will stay on continuously. Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press | again to turn the ﬂashers off. Turn and Lane-Change Signals Lighting 5-3 Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change. Hold it there until the lane change is completed. The lever returns to its starting position whenever it is released. If after signaling a turn or a lane change the arrow ﬂashes rapidly or does not come on, a signal bulb may be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 9-38. An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. 5-4 Lighting Fog Lamps # (Fog Lamps): For vehicles with fog lamps, move the band on the turn signal/multifunction lever to # to turn them on. The fog lamps only come on when the headlamps are on low beam. Some localities have laws that require the headlamps to be on along with the fog lamps. Interior Lighting Instrument Panel Illumination Control Use the trip odometer knob located on the right side of the instrument panel cluster to adjust the instrument panel brightness. Turn the knob clockwise or counterclockwise to brighten or dim the instrument panel. The brightness of the instrument panel lights decreases when the headlamps are on. Dome Lamps The interior lamps control is located on the overhead lamp. To change the interior lamps setting, slide the switch to one of the following positions: OFF: Turns the lamp off. ON: Keeps the lamp on all the time. Door: Turns the lamp on when any door or the liftgate is opened. The lamp goes off when all the side doors and the liftgate are closed. If the lamp switch is in the door position and a door is left open, the lamps will go off automatically after 20 minutes. Lighting 5-5 Battery Power Protection The vehicle has a battery saver feature designed to protect the vehicle’s battery. This feature will only work with the dome lamp in the Door position. When any interior lamp is left on and the ignition is turned off, the battery rundown protection system automatically turns the lamp off after 20 minutes. This prevents draining of the battery. Reading Lamps For vehicles with a sunroof, there is a reading lamp near the sunroof switch. OFF: Turns the lamp off. ON: Keeps the lamp on all the time. Door: Turns the lamp on when any door or the liftgate is opened. The lamp goes off when all the side doors and the liftgate are closed. Lighting Features Entry Lighting After all the doors and liftgate are closed, and the key is out of the ignition, in LOCK/OFF or ACC/ ACCESSORY, the light remains on for about 15 seconds and then goes out, except under the following conditions: • The ignition is turned to ACC/ ACCESSORY or ON/RUN after all the doors and liftgate are closed. • All the doors and the liftgate are locked and the light is still on. When any door is unlocked with the key or Remote Keyless Entry (RKE) system transmitter, the light comes on for 15 seconds, even if the door is not opened. 5-6 Lighting ✍ NOTES Infotainment System 6-1 For more information, see Defensive Driving on page 8-2. Notice: Contact your dealer/ retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 8-18 for more information. Infotainment System Introduction Introduction ..........................6-1 Operation .............................6-2 Radio AM-FM Radio .......................6-4 Satellite Radio ......................6-6 Radio Reception ...................6-8 Fixed Mast Antenna ...............6-8 Satellite Radio Antenna ..........6-9 Audio Players CD Player ............................6-9 MP3 ..................................6-11 Auxiliary Devices .................6-14 Introduction Read the following pages to become familiar with the audio system’s features. { CAUTION Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: • Become familiar with the operation and controls of the audio system. • Set up the tone, speaker adjustments, and preset radio stations. 6-2 Infotainment System Operation The date display times out and goes back to the normal radio and time display. To adjust the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. 2. Press the PWR VOL (Power/ Volume) knob to turn on the radio. 3. Press the CLOCK button, and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) categories display. 4. Press the button under the category to be adjusted. 5. To increase the time or date, do one of the following: turn the TUNE ADJ (Tune/Adjust) knob clockwise, press SEEK/ TRACK y, press FWD ( (Forward), or continue to press the button under the category to be adjusted. Radio with CD (MP3) shown, Radio with CD (Base) similar Playing the Radio PWR VOL (Power/Volume): Press to turn the radio on and off. Turn the PWR VOL knob to adjust the volume. CLOCK: Press to adjust the time. Setting the Clock The date does not automatically display. To see the date press the CLOCK button while the radio is on. 6. To decrease the time or date, do one of the following: turn the TUNE ADJ knob counterclockwise, press SEEK/TRACK z, or press REV ) (Reverse). 7. To save the settings, press the CLOCK button, or let the display time out. To change the time default setting from 12 hour to 24 hour, and to change the date default setting from month/day/year to day/month/year: 1. Press the CLOCK button and then the button below the forward arrow label on the display. The 12H and 24H, and the date MMDD (month and day) and DDMM (day and month) categories will display. 2. Press the button below the 12H or 24H label, and the date MMDD (month and day) or DDMM (day and month) label to choose how the radio displays the time and date. 3. To save the settings, press the CLOCK button, or let the screen time out. Setting the Tone (Bass/Midrange/Treble) To adjust the bass, midrange, and treble: 1. Press the TUNE ADJ knob. 2. Turn the TUNE ADJ knob, or press the button below BASS, MID, or TREB so it is highlighted. 3. Press the TUNE ADJ knob to select BASS, MID, or TREB. 4. Turn the TUNE ADJ knob to adjust the level. 5. Press the TUNE ADJ knob to set the adjustment. Infotainment System 6-3 EQ (Equalization): To select customized equalization settings: 1. Press the EQ button. 2. Press the button below the tab: POP, ROCK, COUNTRY, TALK, JAZZ, and CLASSICAL. Adjusting the Speakers (Balance/Fade) To adjust the balance or fade, perform the following steps: 1. Press the TUNE ADJ knob. 2. Turn the TUNE ADJ knob or press the button below BAL FADE so it is highlighted. 3. Press the TUNE ADJ knob to select the tone to adjust. 4. Turn the TUNE ADJ knob to adjust the audio balance to the right or the left speakers and the fade to adjust the audio volume to the front or rear speakers. 5. Press the TUNE ADJ knob to set the adjustment. 6-4 Infotainment System Setting Preset Stations FAV (Favorites): Press to select up to six pages of favorites. Each page contains six favorite stations, and each page of favorites can contain any combination of AM, FM, or XM™ (if equipped) stations. For vehicles without XM, only four pages of favorites are available. To setup the number of favorites pages: 1. Press the MENU button to display the radio setup menu. 2. Press the button located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the button located below the displayed page numbers. 4. Press the FAV button, or let the menu time out, to return to the radio screen. To store a radio station as a favorite: 1. Tune to the desired radio station. 2. Press the FAV button to display the page where it can be stored. 3. Press and hold one of the six buttons until a beep sounds. 4. Repeat the steps to store another radio station. Radio AM-FM Radio Radio Data System (RDS) The audio system has Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS: • Stations can be selected based on programming. • Stations with traffic announcements can be selected. • Announcements concerning local and national emergencies can be received. • Messages display from radio stations. RDS relies on receiving speciﬁc information from radio stations and only works when the information is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. Contact the radio station if this happens. When the radio is tuned to an RDS station, the station name or call letters display instead of the frequency. RDS stations can also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast. RDS Messages ALERT: Displays when local or national emergency announcements are received. If the radio tunes to a related network station for the announcement, it returns to the original station when the announcement ends. The announcement should be heard even if the volume is low or a CD is playing. If a CD is playing, it will stop playing during the announcement. • The RDS alert feature is not supported by all RDS radio stations. • The RDS alert feature cannot be turned off. • Alert is not affected by tests of the emergency broadcast system. MSG (Message): Displays if the current RDS station has a message. The message displays the artist, song title, call in phone numbers, etc. If the entire message does not display, parts of the message appear every three seconds until the message is completed. MSG disappears from the display once the completed message has displayed. Infotainment System 6-5 Finding a Station BAND: Press to select AM, FM, or XM (if equipped). TUNE ADJ (Tune/Adjust): Turn to select radio stations. y SEEK TRACK z: Press to go to the previous or next radio station. The radio only stops at stations with a strong signal. SCAN: Press to enter scan mode. The radio will display Scanning, then goes to the next station, plays for a few seconds, then continues on to the next station. Press SCAN again to stop scanning. The radio only stops at stations with a strong signal. INFO (Information) (FM-RDS, XM™ Satellite Radio Service, and MP3 Features): Press to display information for the current FM-RDS, XM station, or MP3 song. Choose from Channel, Song, Artist, and CAT (category). NO INFO displays when information is not available from the station. 6-6 Infotainment System Satellite Radio Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in your vehicle. A service fee is required to receive the XM service. For more information, contact XM at www.xmradio.com or call 1-800-929-2100 in the U.S. and www.xmradio.ca or call 1-877-438-9677 in Canada. Finding a Station BAND: Press to select AM, FM, or XM. TUNE ADJ (Tune/Adjust): Turn to select radio stations. y SEEK TRACK z: Press to go to the previous or next radio station. The radio only stops at stations with a strong signal. SCAN: Press to enter scan mode. The radio will display Scanning, then goes to the next station, plays for a few seconds, then continues on to the next station. Press SCAN again to stop scanning. The radio only stops at stations with a strong signal. INFO (Information) (FM-RDS, XM™ Satellite Radio Service, and MP3 Features): Press to display information for the current FM-RDS, XM station, or MP3 song. Choose from Channel, Song, Artist, and CAT (category). NO INFO displays when information is not available from the station. Finding a Category (CAT) Station XM stations are organized in categories. To select and ﬁnd a desired category: 1. Press the CAT button. 2. Turn the TUNE ADJ knob to select a category. 3. Press y or z to go to the category’s ﬁrst station, when the desired category is displayed. 4. Press y or z to go to another station within the selected category. 5. Press CAT to exit the category select mode or wait for CAT to time out. If CAT times out and is no longer on the display, return to Step 1. NOT FOUND displays if the desired category cannot be found. Scanning Categories (CAT) To scan a desired category: 1. Press the CAT button to enter the category select mode. 2. Turn the TUNE ADJ knob to select a category. 3. Press y or z for two seconds to scan the stations in the selected category. 4. Press y or z again to stop scanning. NOT FOUND displays if the desired category cannot be found. XM Radio Messages xL (Explicit Language Channels): These channels, or any others, can be blocked by calling 1-800-852-XMXM (9696). Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. CH Off Air: This channel is not currently in service. Tune in to another channel. CH Unauth: This channel is blocked or cannot be received with your XM Subscription package. CH Unavail: This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No Info: No artist, song title, category, or text information is available at this time on this channel. The system is working properly. Infotainment System 6-7 Not Found: There are no channels available for the selected category. The system is working properly. XM Locked: The XM receiver in the vehicle may have previously been in another vehicle. For security purposes, XM receivers cannot be swapped between vehicles. If this message is received after having the vehicle serviced, check with your dealer/retailer. Radio ID: If tuned to channel 0, this message will alternate with the XM Radio 8 digit radio ID label. This label is needed to activate the service. Consult with your dealer/retailer. Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Chk XMRcvr: If this message does not clear within a short period of time, the receiver may have a fault. Consult with your dealer/retailer. 6-8 Infotainment System Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. FM FM signals only reach about 10 to 40 miles (16 to 65 km). Although the radio has a built-in electronic circuit that automatically works to reduce interference, some static can occur, especially around tall buildings or hills, causing the sound to fade in and out. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio. XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the XM signal for a period of time. Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference can cause an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off. Fixed Mast Antenna The ﬁxed mast antenna can withstand most car washes without being damaged as long as it is securely attached to the base. If the mast becomes slightly bent, straighten it out by hand. If the mast is badly bent, replace it. Occasionally check to make sure the antenna is tightened to its base. If tightening is required, tighten by hand. Satellite Radio Antenna For vehicles with XM™ Satellite Radio Service, the antenna is located on the roof of the vehicle. Keep the antenna clear of obstructions for clear radio reception. If the vehicle has a sunroof, the performance of the XM system may be affected if the sunroof is open. Infotainment System 6-9 Y (EJECT): Press and release to eject a CD. Once ejected it can be removed. If the CD is not removed after several seconds the CD player automatically pulls the disc back into the player and starts playing. TUNE ADJ: Turn the TUNE ADJ knob to select tracks on the CD. y SEEK TRACK z: Press y to go to the start of the current track, if more than ten seconds have played. Press z to go to the next track. Holding or pressing y or z multiple times causes the player to continue moving backward or forward through the tracks on the CD. Audio Players CD Player Playing a CD The CD player can play the smaller 8 cm (3 inch) single CDs with an adapter ring. 1. Insert a CD label side up partway into the slot. 2. The CD player pulls the CD in and begins playing. 3. The CD symbol and track number displays. The CD stays in the player if the ignition or radio is turned off. If the CD was the last source selected, it resumes playing when the radio is turned on. 6-10 Infotainment System ( FWD REV ) (Fast Forward/ Fast Reverse): Press and hold ( to advance playback quickly within a track. Release to resume playing the track. Press and hold ) to reverse playback quickly within a track. Release to resume playing the track. BAND: Press to listen to the radio when a CD is playing. CD/AUX (CD/Auxiliary): Press to play a CD when listening to the radio. Press the CD/AUX button again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, “No Aux Input Device” displays. See “Using the Auxiliary Input Jack” later in this section. INFO (Information): Press to switch the display between the track number, elapsed time of the track, and the time. When the ignition is off, press this button to display the time. EQ (Equalization): Press to select an equalization setting while playing a CD. See “EQ” listed previously for more information. If an EQ setting is selected for a CD, it is activated each time a CD is played. Care of CDs The sound quality of the CD player can be reduced because of: • The CD-R quality. • The method of recording the CD-R. Store CD-R(s) in their original cases or other protective cases and away from dust and direct sunlight. The CD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD may not play properly or at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge. To clean a CD, use a soft lint free cloth, or dampen a clean soft cloth in a mild neutral detergent solution mixed with water. Wipe the CD from the center to the edge. • The quality of the music that has been recorded on the CD-R. • The way the CD-R has been handled. Care of The CD Player Use a marking pen to identify CDs, do not add labels. Do not use CD lens cleaners; they could damage the CD player. Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error displays, see “CD Messages” later in this section. Playing an MP3 CD-R Disc Radios with the MP3 feature are capable of playing an MP3 CD-R disc. See MP3 on page 6-11 for more information. CD Messages If the CD ejects, it could be for one of the following reasons: • The CD player is very hot. When the temperature returns to normal, the CD should play. • The road is very rough. When the road becomes smoother, the CD should play. • The CD is dirty, scratched, wet, or upside down. • The air is very humid. If so, wait about an hour and try again. • The format of the CD might not be compatible. See ‘‘Using an MP3’’ later in this section. • A problem may have occurred while burning the CD. • The label could be caught in the CD player. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. If the radio displays an error message, write it down and provide it to your dealer/ retailer when reporting the problem. Infotainment System 6-11 MP3 MP3 CD-R Disc MP3 Format The MP3 player will only play CD-R discs. It can read and play a maximum of: • 50 folders • 11 folders in depth • 50 playlists • 10 sessions • 255 ﬁles All folders, playlists, sessions and ﬁles over the maximum are ignored. Record an MP3 disc: • Onto a CD-R disc. • Record playlists with an .m3u or .wpl extension. • Do not mix standard audio and MP3 ﬁles on the same disc. • Record the entire disc at once. • Finalize the disc when recording an MP3 disc with multiple sessions. 6-12 Infotainment System Root Directory The root directory is treated as a folder. All .mp3 ﬁles in the root directory are accessed before folders in the root directory. Empty Directory or Folder Empty folders and directories do not display. The system ignores empty directories and folders and advances to the next directory or folder that has .mp3 ﬁles in it. No Folder On a CD that contains only .mp3 ﬁles in the root directory the next and previous folder functions do not work. On a CD that contains playlists and .mp3 ﬁles the next and previous folder functions search playlists ﬁrst and then search .mp3 ﬁles in the root folder. Order of Play CDs that have playlists play the tracks in the following order: 1. After the ﬁrst track in the ﬁrst playlist ends, play continues sequentially through all tracks in each playlist 2. After the last track of the last playlist ends, play restarts from the ﬁrst track of the ﬁrst playlist. CDs that do not have playlists play the tracks in the following order: 1. The ﬁrst ﬁle in the root directory plays. 2. After all ﬁles from the root directory have played, ﬁles in the folders play. 3. After playing the last ﬁle from the last folder, play restarts with the ﬁrst ﬁle in the root directory. File System and Naming The radio display shows, track names that are shorter than 39 characters. Names that are longer are shortened. The track name appears as: • The song name that is in the ID3 tag. • The ﬁle name without the ﬁle extension if the song name is not in the ID3 tag. Preprogrammed Playlists Playlists are accessed before ﬁles or folders in the root directory. Preprogrammed playlists created by WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed and are treated as special folders containing compressed audio song ﬁles. Music Navigator The music navigator feature lets MP3 CDs play in order by artist or album. • The MP3 player scans the disc • to sort the ﬁles by artist and album ID3 tag information. It can take several minutes to scan the disc depending on the number of MP3 ﬁles recorded to the CD-R. • The radio starts playing while the disc is being scanned. • After the scan is ﬁnished, the disc starts playing. Playing an MP3 The MP3 player can play the smaller 3 inch (8 cm) single CDs with an adapter ring. 1. Insert a CD label side up partway into the slot. 2. The CD player pulls the CD in and begins playing. 3. The CD stays in the player if the 4. ignition or radio is turned off. If the CD was the last source selected, it resumes playing when the radio is turned on. Y (EJECT): Press and release to eject a CD. Once the disc is ejected it can be removed. If the CD is not removed after several seconds the CD player automatically pulls the disc back into the player and starts playing. y SEEK TRACK z: Press to go to the start of the current track, if more than ten seconds have played. Press z to go to the next track. Holding or pressing y or z multiple times will cause the player to continue moving backward or forward through the tracks on the CD. Infotainment System 6-13 ( FWD REV ) (Fast Forward/ Fast Reverse): Press and hold ( to advance playback quickly within a track. Release ( to resume playing the track. Press and hold ) to reverse playback quickly within a track. Release ( to resume playing the track. BAND: Press to listen to the radio when a CD is playing. INFO (Information): Press when an MP3 CD is loaded, then press the button below the Song, Artist, Album, or Folder label to view the information. CD/AUX (CD/Auxiliary): Press to play a CD when listening to the radio. Press the CD/AUX button again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, “No Aux Input Device” displays. PWR VOL (Power/Volume): Turn to adjust the volume. Additional volume adjustments may have to be made from the portable device if the volume is too quiet or not loud. BAND: Press to listen to the radio when a portable audio device is playing. CD/AUX (CD/Auxiliary): Press to play a CD when a portable audio device is playing. Press again and the system begins playing audio from the connected portable audio player. Auxiliary Devices The radio has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. An external audio device such as an iPod, laptop computer, MP3 player, CD changer, etc. can be connected to the auxiliary input jack for use as another audio source. To use a portable audio player, connect a 3.5 mm (1/8 inch) cable to the radio’s front auxiliary input jack. When a device is connected, press the radio CD/AUX button to begin playing audio from the device over the vehicle speakers. 6-14 Infotainment System RDM (Random): Press the button below the RDM label to hear the tracks in random order. S c (Previous Folder): Press the button below to go to the ﬁrst track in the previous folder. c T (Next Folder): Press the button below to go to the ﬁrst track in the next folder. h (Music Navigator): Press the button below to play MP3 ﬁles in order by artist or album. SORT: Press the button below the SORT label to change between playback by artist or album while using the Music Navigator. BACK: Press the button below the BACK label to return to the main music navigator screen. S T (Previous/Next): Press the button below to go to the next or previous artist or album in alphabetical order while using the Music Navigator. Climate Controls Climate Control Systems Climate Controls 7-1 The heating, cooling, and ventilation for the vehicle can be controlled with this system. Climate Control Systems Climate Control Systems ........7-1 Air Vents Air Vents .............................7-4 Maintenance Passenger Compartment Air Filter .............................7-4 A. Air Delivery Mode Control B. Fan Control C. Temperature Control D. Recirculation E. Rear Window Defogger F. Air Conditioning 7-2 Climate Controls Fan Control 9 (Fan): Turn the center knob toward 4 to turn the system on or increase fan speed. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter may need to be replaced. For more information, see Passenger Compartment Air Filter on page 7-4 and Scheduled Maintenance on page 10-3. Temperature Control Turn the right knob clockwise or counterclockwise to increase or decrease the temperature inside the vehicle. Air Delivery Mode Control Turn the left knob to select from the following modes: H (Vent): Air is directed to the upper instrument panel outlets. ) (Bi-Level): Air is directed to the upper instrument panel outlets and the ﬂoor outlets. 6 (Floor): Air is directed to the ﬂoor and side window outlets. - (Defog): Air is directed between the windshield, side windows, instrument panel outlets and the ﬂoor outlets. Use the defog mode to clear the inside of the windshield of fog or moisture and to warm the passengers. The air conditioning compressor runs automatically in this setting without pressing A/C, unless the outside temperature is at or below 32°F (0°C). 1 (Defrost): Air is directed to the windshield, instrument panel outlets and the side windows. Use the defrost mode to remove fog or frost from the outside of the windshield more quickly. The air conditioning compressor runs automatically in this setting without pressing A/C, unless the outside temperature is at or below 32°F (0°C). Do not drive the vehicle until all the windows are clear. Recirculation ? (Recirculation): Press to turn the recirculation mode on or off. An indicator light shows that it is on. This mode recirculates the air inside the vehicle and helps to heat or cool the air more quickly. It can be used to prevent outside air and odors from entering the vehicle. Press the button again to turn the recirculation mode off and the outside air mode on. Recirculation is automatically turned off when the climate control system mode knob is turned to defog, defrost, or is positioned between modes. Air Conditioning For vehicles with this feature, there will be the following controls: A/C (Air Conditioning): Press to turn the air conditioning system on or off. An indicator light shows that it is on. MAX A/C (Maximum Air Conditioning): Press the A/C and recirculation buttons at the same time to select MAX A/C. On hot days, open the windows to let hot inside air escape; then close them. The vehicle will cool quicker and the A/C system operates more

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Pontiac VIBE Owners Manual