2012 Nissan Titan Owners Manual

(if so equipped).

To fill the windshield-washer fluid reservoir, lift the cap off the reservoir and pour the windshield- washer fluid into the reservoir opening.

Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield- washer antifreeze. Follow the manufacturer’s in- structions for the mixture ratio.

Refill the reservoir more frequently when driving conditions require an increased amount of windshield-washer fluid. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.

CAUTION

for windshield-washer

● Do not substitute engine anti-freeze coolant fluid. This may result in damage to the paint. ● Do not fill the windshield-washer fluid reservoir with washer fluid concen- trates at full strength. Some methyl al- cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield- washer fluid reservoir.

● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the windshield-washer fluid reser- voir. Do not use the windshield-washer fluid reservoir to mix the washer fluid concentrate and water.

Maintenance and do-it-yourself 8-13

● Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion.

● When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.

● Battery posts, terminals and related ac- cessories contain lead and lead com- pounds. Wash hands after handling.

● Keep battery out of

children.

the reach of

● Do not tip the battery. Keep the vent

caps tight and the battery level.

WDI0224
1. Remove the vent caps with a screwdriver as shown. Use a cloth to protect the battery case.

BATTERY

● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water.

● Make certain the terminal connections are

clean and securely tightened.

● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.

WARNING

● Do not expose the battery to flames, an electrical spark or a cigarette. Hydro- gen gas generated by the battery is ex- plosive. Explosive gases can cause blindness or injury. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. Sulfuric acid can cause blindness or injury. After touch- ing a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.

8-14 Maintenance and do-it-yourself

VARIABLE VOLTAGE CONTROL SYSTEM

Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.

WDI0566

CAUTION

● Do not ground accessories directly to the battery terminal. Doing so will by- pass the variable voltage control sys- tem and the vehicle battery may not charge completely.

● Use electrical accessories with the en- gine running to avoid discharging the vehicle battery.

Your vehicle is equipped with a variable voltage control system. This system measures the amount of electrical discharge from the battery and controls voltage generated by the generator.

Maintenance and do-it-yourself 8-15

2. Check the fluid level

in each cell.

WDI0529
If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill. Reinstall the vent caps.

DRIVE BELT

The current sensor 䊊A is located near the battery along the negative battery cable. If you add elec- trical accessories to your vehicle, be sure to ground them to a suitable body ground such as the frame or engine block area.

WDI0661

1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer.

2. Have the belt checked regularly for condi- tion and tension in accordance with the maintenance the “NISSAN Service and Maintenance Guide”.

schedule

found

in

Power steering fluid pump Automatic belt tensioner

1. 2. 3. Water pump 4. Cooling fan 5. 6. Crankshaft pulley 7. Generator

Air conditioner compressor

WARNING

Be sure the ignition switch is in the OFF or LOCK position before servicing drive belt. The engine could rotate unexpectedly.

8-16 Maintenance and do-it-yourself

SPARK PLUGS

AIR CLEANER

WARNING

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs.

SDI1895

REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped 䊊A spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the “NISSAN Service and Maintenance Guide”. Do not service platinum-tipped spark plugs by cleaning or re- gapping. ● Always replace spark plugs with rec-

ommended or equivalent ones.

WDI0712
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide.”

To remove the air cleaner filter: 䊊1 Unlatch the clips and move the air cleaner

cover upward.

2. Remove the air cleaner filter.

3. Wipe the inside of the air cleaner filter hous-

ing and the cover with a damp cloth.

Maintenance and do-it-yourself 8-17

To replace the filter, perform the following proce- dure:

WDI0619
1. Remove the 2 lower glove box hinge pins 䊊A . Remove the glove box from the opening and let it hang by the cord.

NOTE:

After installing a new air cleaner, make sure the air cleaner cover is seated in the housing and latch the clips.

WARNING

● Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.

● Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of air- borne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the “NISSAN Service and Maintenance Guide” for change intervals.

8-18 Maintenance and do-it-yourself

WINDSHIELD WIPER BLADES

CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.

CAUTION

Worn windshield wiper blades can dam- age the windshield and impair driver vision.

Maintenance and do-it-yourself 8-19

LDI0387
2. Remove the filter cover bolt and remove the

filter cover.

LDI0404

NOTE:

The filters are marked with air flow arrows. The end of the filter with the arrow should face the rear of the vehicle. The arrows should face downward.

3.

Insert the first filter into the housing and slide it over to the right. Insert the second filter into the housing.

Install the glove box door.

4. Replace the filter cover. 5. 6. Fill out the date information on the small replacement label and attach it to the glove box lid.

6. Return the wiper to its original position and release it until it has made contact with the windshield.

CAUTION

● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.

● Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.

WDI0408

REPLACING Replace the wiper blades if they are worn.

1. Lift the wiper arm away from the windshield. 䊊2 Push the release tab, then move the wiper

blade down the wiper arm to remove.

䊊3 Remove the wiper blade. 4.

Insert the new wiper blade onto the wiper arm until it clicks into place.

5. Rotate wiper blade so the dimple is in the

groove.

8-20 Maintenance and do-it-yourself

WDI0629
If you wax the surface of the hood, be careful not to let wax get into the windshield washer nozzle 䊊A . This may cause clogging or improper wind- shield washer operation. If wax gets into the nozzle, remove it with a needle or small pin 䊊B .

BRAKES

FUSES

Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the “NISSAN Ser- vice and Maintenance Guide”.

If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes.

The front and rear disc-type brakes self-adjust every time the brake pedal is applied.

WARNING

See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal.

Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard.

Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system.

LDI0455
Two types of fuses are used. Type 䊊A is used in the fuse boxes in the engine compartment. Type 䊊B is used in the passenger compartment fuse box. Type A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type A fuses can be installed in the engine com- partment and passenger compartment fuse boxes.

Maintenance and do-it-yourself 8-21

3. Remove the fuse box cover by pushing the

tab and lifting the cover up.

4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.

LDI0457
If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. Type B fuses cannot be installed in the under- hood fuse boxes. Only use type A fuses in the underhood fuse boxes.

LDI0380

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not come on, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the engine hood.

8-22 Maintenance and do-it-yourself

3. Pull the fuse box cover to remove. 4. Remove the fuse with the fuse puller.

5.

6.

WDI0452
If the fuse is open 䊊A , replace it with a new fuse 䊊B . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only Genuine NISSAN parts.

PASSENGER COMPARTMENT

LDI0618

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the glove box to access the fuse box

cover.

Maintenance and do-it-yourself 8-23

WDI0452

LDI0456

5.

Type A

If the fuse is open 䊊A , replace it with an equivalent good fuse 䊊B .

6. Push the fuse box cover to install. 7.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Type B

LDI2035

Extended storage switch If any electrical equipment does not operate, remove the extended storage switch and check for an open fuse.

NOTE: The extended storage switch is used for long term vehicle storage. Even if the ex- tended storage switch is broken it is not necessary to replace it. Replace only the open fuse in the switch with a new fuse.

8-24 Maintenance and do-it-yourself

BATTERY REPLACEMENT

CAUTION

Be careful not to allow children to swallow the battery or removed parts.

How to replace the extended storage switch: 1. To remove the extended storage switch, be sure the ignition switch is in the OFF or LOCK position.

2. Be sure the headlight switch is in the OFF

position.

3. Remove the fuse box cover. 4. Pinch the locking tabs 䊊1 found on each

side of the storage switch.

5. Pull the storage switch straight out from the

fuse box 䊊2 .

Maintenance and do-it-yourself 8-25

● Do not touch the internal circuit and electric

terminals as it could cause a malfunction.

● When changing the battery, do not let dust

or oil get on the keyfob.

● There is danger of explosion if a lithium bat- tery is incorrectly replaced. Replace only with the same or equivalent type.

Recommended battery: CR2025 or equivalent. 䊊4 Close the lid securely.

5. Press the

button, then the

button two or three times to check the key- fob operation.

KEYFOB (if so equipped) Replace the battery in the keyfob as follows: 䊊1 Open the lid using a coin 䊊A . 䊊2 Remove the battery 䊊B .

8-26 Maintenance and do-it-yourself

䊊3

LDI2026
Install a new battery 䊊C with the “+” facing down.

● Hold the battery by the edges. Holding the battery across the contact points will seri- ously deplete the storage capacity.

If the battery is removed for any reason other than replacement, perform step 5.

● An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. ● The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

● The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For Canada: This device complies with RSS-210 of In- dustry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, in- cluding interference that may cause unde- sired operation of the device.

LIGHTS

HEADLIGHTS Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Be- cause the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.

CAUTION

● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

● When handling the bulb, do not touch

the glass envelope.

● DO NOT TOUCH THE BULB WITH BARE

HANDS.

● Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture and smoke may enter the headlight body and affect the per- formance of the headlight.

● Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.

NOTE:

Use the same number and wattage as shown in the chart.

Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer. FOG LIGHTS (if so equipped) Replacing the fog light bulb

CAUTION

● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

● When handling the bulb, do not touch

the glass envelope.

● Use the same number and wattage as originally installed as shown in the chart.

Maintenance and do-it-yourself 8-27

● Do not leave the bulb out of the fog light for a long period of time as dust, mois- ture and smoke may enter the fog light body and affect the performance of the fog light.

NOTE: To adjust the fog light vertical aim: Access the aiming screw from underneath the front bumper. The aiming screw is located on the bottom of the fog light housing. Turn the screw clockwise to raise the pattern. Turn the screw counterclockwise to lower the pattern.

LDI0382

1. Disconnect the negative (-) battery cable.

2. The fog light is accessible in front of the

front tire and behind the bumper.

3. Disconnect the bulb connector 䊊1 . 4. Rotate the bulb counterclockwise and re-

move.

5. Remove by pulling it straight out of the fog light assembly. Do not shake or rotate the bulb when removing it. Do not touch the glass envelope.

6.

Install in the reverse order of removal.

8-28 Maintenance and do-it-yourself

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.

Headlight assembly

High Low Park/Turn Sidemarker

Side turn signal light* (if so equipped) Front fog light (if so equipped) Puddle light (if so equipped) Room/map lights (front) Personal lights Footwell (if so equipped) Vanity mirror light (if so equipped) Step light (if so equipped) High-mounted stop light/cargo lights* Rear combination light

Tail/Stop Backup (reversing) Turn

Tailgate light (if so equipped) License plate light

65
55
28/8
3.8
— 27.5

3.4
1.8
3.8
12.8

27/8
18
27
18

9005 (HB3) 9006 (HB4)

3457K

194
LED 880
906LF

–

AL67
158
– 194
912LF

3157K 921LF 3156K

921
W5W

* See a NISSAN dealer for replacement. Always check with the Parts Department at a NISSAN dealer for the latest parts information.

Maintenance and do-it-yourself 8-29

1. 2. 3. 4.

Room/map light (if so equipped) Personal lights (if so equipped) Step light (if so equipped) Puddle light/Side turn signal light (if so equipped)

5. High-mount stoplight/cargo lights 6. 7.

License plate light Rear combination/tailgate light (if so equipped) assembly Fog light (if so equipped)

8. 9. Headlight assembly

8-30 Maintenance and do-it-yourself

WDI0409

WDI0263

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.

first remove the lens,

Indicates bulb removal Indicates bulb installation

Personal lights (If so equipped)

Use a cloth 䊊1 to protect the housing.

Vanity mirror (If so equipped)

Use a cloth 䊊1 to protect the housing.

LDI0364

LDI0385

Interior/map lights

Use a cloth 䊊1 to protect the housing.

LDI0389

Maintenance and do-it-yourself 8-31

Step light (If so equipped) Use a cloth 䊊1 to protect the housing.

Puddle light (If so equipped)

Use a cloth 䊊1 to protect the housing.

License plate light

LDI0341

LDI0388

WDI0411

8-32 Maintenance and do-it-yourself

WHEELS AND TIRES

If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all 4 tires except the spare. When the low tire pressure warning light is lit and the CHECK TIRE PRESSURE warning appears in the ve- hicle information display, one or more of your tires is significantly under-inflated. If equipped, the system also displays pres- sure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not de- tect a sudden drop in tire pressure (for example a flat tire while driving).

Rear combination light

LDI0410

refer

more

details,

For to “Warning/Indicator Lights and Audible Reminders” in the “Instruments and con- trols” section, “Tire pressure information” in the “Display screen, heater, air condi- tioner, audio and phone systems” section, “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” sec- tion, and “Flat tire” in the “In case of emer- gency” section. Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long dis- tance trips. The recommended tire pres- sure specifications are shown on the F.M.V.S.S./C.M.V.S.S. certification label or the Tire and Loading Information label under the “Cold Tire Pressure” heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: ● Most tires naturally lose air over time.

Maintenance and do-it-yourself 8-33

● For additional

information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Information” (Canada) in the Warranty Infor- mation Booklet.

Safety

● Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.

WARNING

is

located on

● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross Vehicle Weight Rating the (GVWR) certifica- F.M.V.S.S./C.M.V.S.S. tion label. The vehicle weight ca- pacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your ve- hicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling character- istics and could also lead to a serious accident. Loading be- yond the specified capacity may also result in failure of other ve- hicle components.

● Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

8-34 Maintenance and do-it-yourself

䊊5 Tire size - refer to “Tire labeling” later

in this section. 䊊6 Spare tire size.

Tire and loading information label 䊊1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle.

䊊2 Vehicle load limit: See loading infor- mation in the “Technical and con- sumer information” section.

䊊3 Original tire size: The size of the tires originally installed on the vehicle at the factory.

LDI0485
䊊4 Cold tire pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicle’s GVWR.

Maintenance and do-it-yourself 8-35

3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare to the specifica- tion shown on the Tire and Loading Information label.

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.

6. 7. Check the pressure of all other tires,

including the spare.

Size

Front Original Tire: P265/70R18
P275/70R18
P275/60R20
Rear Original Tire: P265/70R18
P275/70R18
P275/60R20
Spare Tire: P265/70R18
P275/70R18
P275/60R20

Cold Tire Inflation Pressure

240 kPa, 35 PSI

240 kPa, 35 PSI

240 kPa, 35 PSI

LDI0393

Checking tire pressure 1. Remove the valve stem cap from the

tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.

8-36 Maintenance and do-it-yourself

Example

WDI0394

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

䊊1 Tire size (example: P215/65R15 95H) 1. P: The “P” indicates the tire is de- signed for passenger vehicles (not all tires have this information).

2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge.

3. Two-digit number (65): This number, known as the aspect ratio, gives the tire’s ratio of height to width.

Example

WDI0395

4. R: The “R” stands for radial. 5. Two-digit number (15): This number is the wheel or rim diameter in inches. 6. Two- or three-digit number (95): This number is the tire’s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating.

Maintenance and do-it-yourself 8-37

䊊3 Tire ply composition and material The number of layers or plies of rubber- coated fabric in the tire. Tire manufactur- ers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 䊊4 Maximum permissible inflation pres- sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible in- flation pressure. 䊊5 Maximum load rating This number indicates the maximum load in kilograms and pounds that can be car- ried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory in- stalled tire. 䊊6 Term of “tubeless” or “tube type” Indicates whether the tire requires an in- ner tube (“tube type”) or not (“tubeless”).

Example

WDI0396

4. Three-digit code: Tire type code

(Optional).

5. Three-digit code: Date of Manufac-

ture.

6. Four numbers represent the week and year the tire was built. For ex- ample, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.

䊊2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the “Depart- ment Of Transportation”. The symbol can be placed above, below or to the left or right of the Tire Identification Number. 2. Two-digit

code: Manufacturer’s

identification mark.

3. Two-digit code: Tire size. 8-38 Maintenance and do-it-yourself

䊊7 The word “radial” The word “radial” is shown if the tire has radial structure. 䊊8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the out- ward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle.

TYPES OF TIRES

WARNING

● When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.

● Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the low tire pres- sure warning system.

● For additional

information regarding tires, refer to “Important Tire Safety In- formation” (US) or “Tire Safety Informa- tion” (Canada) in the Warranty Informa- tion Booklet.

All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ-

ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating “M&S” on the tire sidewall.

If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle.

If you do not,

Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire.

Maintenance and do-it-yourself 8-39

signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufac- turer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully load- ing your vehicle when using tire chains. In addi- tion, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. Tire chains must be installed only on the rear wheels and not on the front wheels. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. Use only the 2WD range when driving on clear paved roads.

If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS

CAUTION

Tire chains/cables should not be installed on P275/60R20 size tires. Installation of the tire chains/cables on P275/60R20 size tires will cause damage to the vehicle. If you plan to use tire chains/cables, you should install P265/70R18 size tires on your vehicle.

Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class “S” chains are de- 8-40 Maintenance and do-it-yourself

WDI0258

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See “Flat tire” in the “In case of emer- gency” section in this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

98 ft-lb (133 N·m)

The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval.

WARNING

● After rotating the tires, check and

adjust the tire pressure.

● Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

● Do not include the spare tire in

the tire rotation. ● For additional

information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Information” (Canada) in the Warranty Infor- mation Booklet.

Safety

● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.

● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified because some tire damage may not be ob- vious. Replace the tires as neces- sary to prevent tire failure and possible personal injury.

technician

● Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact a NISSAN dealer.

● For additional

information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Information” (Canada) in the Warranty Infor- mation Booklet.

Safety

Maintenance and do-it-yourself 8-41

WDI0259

1. Wear indicator 2. Location mark Tire wear and damage

WARNING

● Tires should be periodically in- spected for wear, cracking, bulg- ing or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.

Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual.

WARNING

● The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, VDC system, ground clear- ance, body-to-tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to acci- dents and could result in serious per- sonal injury.

● If your vehicle was originally equipped with 4 tires that were the same size and you are only replacing 2 of the 4 tires, install the new tires on the rear axle. Placing new tires on the front axle may cause loss of vehicle control in some driving conditions and cause an acci- dent and personal injury.

8-42 Maintenance and do-it-yourself

● If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics, affect the VDC system and/or interference with the brake discs. Such interference can lead to decreased braking effi- ciency and/or early brake pad wear. Re- fer to “Wheels and tires” in the “Techni- cal and consumer information” section of for wheel off-set dimensions.

this manual

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

● Do not install a damaged or deformed wheel or tire even if it has been re- paired. Such wheels or tires could have structural damage and could fail with- out warning. ● The use of

retread tires

is not

recommended. ● For additional

information regarding tires, refer to “Important Tire Safety In- formation” (US) or “Tire Safety Informa- tion” (Canada) in the Warranty Informa- tion Booklet.

Four-wheel drive models

CAUTION

Always use tires of the same type, size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires on the front and rear axles which will cause excessive tire wear and may dam- age the transmission, transfer case and differential gears.

If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.

● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Infor- mation” (Canada) in the Warranty In- formation Booklet.

Care of wheels ● Wash the wheels when washing the vehicle

to maintain their appearance.

● Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

● Do not use abrasive cleaners when washing

the wheels.

● Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

● NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

Maintenance and do-it-yourself 8-43

MEMO

8-44 Maintenance and do-it-yourself

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2

Fuel recommendation (without Flexible Fuel Vehicle option). . . . . . . . . . . . . . 9-3
Flexible fuel vehicle (FFV) fuel recommendation (if so equipped). . . . . . . . . . . . . . . . . 9-4
Engine oil and oil filter recommendations . . . . . . . . . . 9-6
Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-9

When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Vehicle identification number (VIN) plate . . . . . . . . . 9-10
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . 9-11
Emission control information label . . . . . . . . . . . . . . . 9-11
Tire and loading information label. . . . . . . . . . . . . . . . 9-12
Air conditioner specification label. . . . . . . . . . . . . . . . 9-12
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-13

Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Securing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Utili-track™ channel system (if so equipped) . . . . . . 9-16
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
Truck-camper loading information . . . . . . . . . . . . . . . . . . 9-22
Crew Cab Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
King Cab models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Special Body vehicles. . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Location for center of gravity . . . . . . . . . . . . . . . . . . . . 9-22
Payload weight capacity. . . . . . . . . . . . . . . . . . . . . . . . 9-23
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . 9-23
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
Towing load/specification. . . . . . . . . . . . . . . . . . . . . . . 9-28
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-30
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-39
Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-39
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-40
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-41
Reporting safety defects . . . . . . . . . . . . . . . . . . . . . . . . . . 9-41
Readiness for inspection/maintenance (I/M) test . . . . . 9-42
Event Data Recorders (EDR). . . . . . . . . . . . . . . . . . . . . . . 9-42
Owner’s Manual/Service Manual order information . . . 9-43

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Recommended Fluids and Lubricants

Capacity (Approximate) US measure 28 gal

Imp measure 23-1/4 gal

Fuel

Engine oil *7

Drain and Refill

With oil filter change 6-7/8 qt Without oil filter 6-1/2 qt change

5-3/4 qt 5-1/2 qt

Cooling system

With reservoir

Automatic transmission fluid Power steering fluid (PSF) Brake fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system oil Transfer fluid Front final drive oil

Rear final drive oil

3-1/4 gal Refill to the proper level according to the instruc- tions in the “Maintenance and do-it-yourself” section.

2-5/8 gal

12.2

— — — 2-1/8 qt 3-3/8 pt

4-1/4 pt

— — — 1-3/4 qt 2-7/8 pt

3-1/2 pt

— — — 2.0
1.6

2.0

Liter 105.8

6.5
6.2

See “Fuel Recommendation (without Flexible Fuel Vehicle Option)” or “Flexible Fuel Ve- hicle (FFV) Fuel Recommendation” later in this section.

(cid:129) Engine oil with API Certification Mark *1
(cid:129) Viscosity SAE 5W-30

Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent Genuine NISSAN Matic S ATF *2
Genuine NISSAN PSF or equivalent *3
Genuine NISSAN Super Heavy Duty Brake Fluid *4 or equivalent DOT 3
NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a) *5
Genuine NISSAN A/C System Oil Type S or equivalent *5
Genuine NISSAN Matic D ATF recommended*6
Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5, Viscosity SAE 80W-90 *8
Genuine NISSAN Differential Oil Synthetic 75W-140 or API GL-5 synthetic gear oil, Vis- cosity SAE 75W-140 *9
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent

1 gal

1-1/4 gal

Windshield-washer fluid (shared be- tween front and rear wipers) *1: For further details, see “Engine oil and oil filter recommendations” in this section. *2: If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission fluid other than Genuine NISSAN Matic S ATF or

Genuine NISSAN Matic J AFT will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty.

*3: DEXRON™ VI type ATF may also be used. *4: Available in mainland USA through a NISSAN dealer. *5: For further details, see “Air conditioner specification label” in this section. *6: Using fluid other than Genuine NISSAN Matic D ATF will cause deterioration in driveability and transfer durability, and may damage the transfer, which is not covered by the NISSAN

4.5

new vehicle limited warranty.

*7: For further details, see “Changing engine oil” in the “Maintenance and do-it-yourself” section. *8: For hot climates, Viscosity SAE 90 is suitable for ambient temperatures above 0° C (32° F). *9: See a NISSAN dealer for service for synthetic oil. 9-2 Technical and consumer information

FUEL RECOMMENDATION (without Flexible Fuel Vehicle option) Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).

CAUTION

● Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.

● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

● Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.

● Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN new vehicle lim- ited warranty.

Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter (WWFC) specifi- cations where it is available. Many of the automo- bile manufacturers developed this specification to improve emission control system and vehicle performance. Ask your service station manager if the gasoline meets the WWFC specifications. Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.

If you use oxygenate-blend gasoline, please take the following precautions as the usage of such

fuels may cause vehicle performance problems and/or fuel system damage.

● The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline.

● If an oxygenate-blend other

than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE.

oxygenate-blend

fuels,

Technical and consumer information 9-3

Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S. government regulations require fuel ethanol dispensing pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy “spark knock.” (“Spark knock” is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you 9-4 Technical and consumer information

ignition timing may result

detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

● E-85 is a mixture of approximately 85% 15% unleaded

ethanol

and

fuel gasoline.

● U.S. government

regulations require ethanol dispensing pumps to be identi- fied by a small, square, orange and black label with the common abbrevia- tion or the appropriate percentage for that region.

FLEXIBLE FUEL VEHICLE (FFV) FUEL RECOMMENDATION (if so equipped) Your vehicle is designed to use (E-85) Fuel Etha- nol, “Regular” unleaded regular gasoline or any percentage of the two fuels combined. U.S. government regulations require Fuel Ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region.

CAUTION

CAUTION

● Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.

Use of other fuels such as Fuel Methanol may cause powertrain damage or a loss of vehicle performance.

General information This information is for Flexible Fuel vehicles (FFV) only. FFV vehicles can be identified by the fuel filler door label that states Ethanol (E-85) or Unleaded Gasoline Only. This section only cov- ers those subjects that are unique to Flexible Fuel vehicles.

CAUTION

Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.

Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel etha- nol and 15% unleaded gasoline.

WARNING

● Ethanol vapors are extremely flam- mable and could cause serious per- sonal injury.

● Never have any smoking materials lit in or near the vehicle when removing the fuel filler cap or filling the tank.

● Do not use E-85 as a cleaning agent and

never use it near an open flame.

Fuel requirements

Your vehicle will operate on both unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane num- ber 91), or E-85 fuel, or any mixture of these two. For the best starting and vehicle driveability re- sults, do not continually switch between E-85
and unleaded regular gasoline. If you must switch fuels, NISSAN recommends the following: ● do not switch when the fuel gauge indicates

less than 1/4 full

● add more than 5 gallons of fuel ● operate the vehicle immediately after refuel-

ing for a period of at least 5 minutes

NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard start- ing and rough idle following start up even if the above recommendations are followed. Starting The characteristics of E-85 fuel make it unsuit- able for use when ambient temperatures fall be- low 0°F (-18°C). In the range of 0°F (-18°C) to 32°F (0°C), you may experience an increase in the time it takes for you engine to start, and a deterioration in drivability (sags and/or hesita- tions) until the engine is fully warmed up.

Fuel consumption Because E-85 fuel contains less energy per gal- lon than gasoline, you will experience an increase in fuel consumption. You can expect your fuel mileage to decrease by about 30% compared to gasoline operation. Replacement parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with etha- nol. Always be sure that your vehicle is serviced with correct ethanol compatible parts.

CAUTION

Replacing fuel system components with non-ethanol compatible components can damage your vehicle and may also affect the warranty coverage.

Maintenance If you operate your vehicle using E-85 fuel, follow the correct maintenance log shown in the “NISSAN Service and Maintenance Guide”.

CAUTION

Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability.

Technical and consumer information 9-5

Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in “Change intervals.” Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle limited war- ranty.

ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.

Select only engine oils that meet the American Petroleum Institute (API) certification or Interna- tional Lubricant Standardization and Approval 9-6 Technical and consumer information

WTI0183
Committee (ILSAC) certification and SAE vis- cosity standard. These oils have the API certifica- tion mark on the front of the container. Oils which do not have the specified quality label should not be used as they could cause engine damage. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used.

CAUTION

The use of any other refrigerant or oil will cause severe damage to the air condition- ing system and will require the replace- ment of all air conditioner system components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.

Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle.

Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance driving at cold out-

side temperatures

● driving in dusty conditions ● extensive idling ● towing a trailer ● stop and go commuting Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule. AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and NISSAN A/C system oil Type S or the exact equivalents.

Technical and consumer information 9-7

SPECIFICATIONS

ENGINE

Model

Type Cylinder arrangement Bore x Stroke Displacement Firing order

Idle speed

A/T (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle

Spark plug

Spark plug gap (Nominal)

Camshaft operation

This spark ignition system complies with the Canadian standard ICES-002.

9-8 Technical and consumer information

VK56DE

Gasoline, 4-cycle, DOHC

8-cylinder, V-block, Slanted at 90° in (mm) 3.858 x 3.622 (98 x 92)

cu in (cm3) 338.78 (5,552)

1–8–7–3–6–5–4–2

No adjustment is necessary.

Standard Model DILFR5A-11

FFV Model DILFR5A-11D

in (mm) 0.043 (1.1)

Timing chain

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Wheels

Tires

Spare tire

18 x 8.0JJ 20 x 8.0JJ

P265/70R18
P275/70R18
P275/60R20
Full size

Overall length

Short wheel base (SWB) Long wheel base (LWB)

Overall width Overall height King Cab - SWB

King Cab - LWB

Crew Cab - SWB

Crew Cab - LWB

Front Track

18 inch tire 20 inch tire

Rear Track

18 inch tire 20 inch tire

Wheelbase

Short wheel base Long wheel base

Gross vehicle weight rating Gross axle weight rating

Front Rear

4x2 (S, SV) 4x4 (S, SV) 4x4 (Pro-4X) 4x2 (S, SV) 4x4 (S, SV) 4x2 (S, SV) 4x2 (SL) 4x4 (S, SV) 4x4 (Pro-4X) 4x4 (SL) 4x2 (S, SV) 4x2 (SL) 4x4 (S, SV) 4x4 (Pro-4X) 4x4 (SL)

in (mm) in (mm) in (mm)

in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) in (mm)

in (mm) in (mm)

in (mm) in (mm)

in (mm) in (mm) lb (kg)

lb (kg) lb (kg)

224.6 (5,704) 244.3 (6,204) 79.5 (2,019)

74.6 (1,896) 76.1 (1,934) 76.6 (1,946) 74.4 (1,891) 76.0 (1,931) 74.7 (1,898) 75.1 (1,908) 76.3 (1,939) 76.9 (1,954) 76.7 (1,949) 74.7 (1,898) 74.9 (1,903) 76.3 (1,939) 76.6 (1,946) 76.4 (1,941)

67.9 (1,725) 68.1 (1,729)

67.9 (1,725) 68.1 (1,729)

139.8 (3,550) 159.5 (4,050) See the “F.M.V.S. S./C.M.V.S.S. cer- tification label” on the center pillar between the driv- er’s side front and rear doors.

Technical and consumer information 9-9

VEHICLE IDENTIFICATION

LTI0085
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

LTI0086
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.