Download PDF Manual


1. Press the


button on the steering


wheel. A tone will sound.


2. Say: “Call” 䊊A . The system acknowledges the command and announces the next set of available commands.


Say: “Call International” to dial more than 10
digits or any special characters.


3. Say the number you wish to call starting with the area code in single digit format 䊊B . If the system has trouble recognizing the correct phone number, try entering the number in the following groups: 3-digit area code,


4-72 Display screen, heater, air conditioner, audio and phone systems


3-digit prefix and the last 4-digits. For ex- ample, 555-121-3354 can be said as “five five five” as the 1st group, then “one two one” as the 2nd group, and “three three five four” as the 3rd group. For dialing more than 10 digits or any special characters, say “In- ternational”. See “How to say numbers” in this section, for more information.


4. When you have finished speaking the phone number, the system repeats it back and an- nounces the available commands.


5. Say: “Dial” 䊊C . The system acknowledges


the command and makes the call.


For additional command options, see “List of voice commands” in this section. Receiving a call When you hear the ring tone, press the button on the steering wheel.


Once the call has ended, press the on the steering wheel.


button


NOTE: If you do not wish to take the call when you button hear the ring tone, press the on the steering wheel.


For additional command options, see “List of voice commands” later in this section. LIST OF VOICE COMMANDS


Main Menu


“Call” or “Call International” “Phone Book” “Memo Pad” “Setup”


When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the com- mands in each sub-menu. Remember to wait for the tone before speaking.


You can say “Help” to hear the list of commands currently available any time the system is waiting for a response.


If you want to end an action without completing it, you can say “Cancel” or “Quit” at any time the system is waiting for a response. The system will end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.


If you want to go back to the previous command, you can say “Go back” or “Correction” any time the system is waiting for a response.


When you get used to the menus in the system, you can talk ahead by saying more than one command at a time. For example, say, “Call five five five one two one two” or “Memo pad record.”


Also, when you get used to the system re- sponses, you can skip ahead to the tone by button on the steering wheel. pressing the button when the However, if you press the system is waiting for a response from you it will end the VR session. “Call”


Main Menu


“Call” or “Call International”


Name (speak name) 䊊A Number (speak digits) 䊊B “Redial” 䊊C “Call Back” 䊊D


Name (speak name) 䊊A If you have stored entries in the Phone Book, you can dial a number associated with a name and location.


Display screen, heater, air conditioner, audio and phone systems 4-73


See “Phone book” later in this section to learn how to store entries.


When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name.


If there are multiple locations associated with the name, the system asks you to choose the loca- tion.


Once you have confirmed the name and location, the system begins the call. Number (speak digits) 䊊B When prompted by the system, say the number you wish to call. Refer to “How to say numbers” and “Making a call by entering a phone number” in this section for more details. “Redial” 䊊C Use the Redial command to call the last number that was dialed within the vehicle.


NOTE:


The system will not redial the last number dialed by the handset keypad.


The system acknowledges the command, re- peats the number and begins dialing.


If a redial number does not exist, the system announces, “There is no number to redial” and ends the VR session. “Call back” 䊊D Use the Call Back command to dial the number of the last incoming call within the vehicle. The system acknowledges the command, re- peats the number and begins dialing. If a call back number does not exist, the system announces, “There is no number to call back” and ends the VR session. International For dialing more than 10 digits or any special characters, please say “international”. When the system acknowledges the command, the system will prompt you to speak the number. During a call During a call there are several command options button on the steering available. Press the wheel to mute the receiving voice and enter com- mands. ● “Help” — The system announces the avail-


able commands.


● “Go back/Correction” — The system an- nounces “Go back,” ends the VR session and returns to the call.


● “Cancel/Quit” — The system announces “Cancel,” ends the VR session and returns to the call.


● “Send/Enter/Call/Dial” — Use the Send command to enter numbers, “*” or “#” during a call. For example, if you were directed to dial an extension by an automated system:


Say: “Send one two three four.”


The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR ses- sion and returns to the call. Say “star” for “*”, Say “pound” for “#”.


● “Transfer call” — Use the Transfer Call com- mand to transfer the call from the Bluetooth姞 Hands-Free Phone System to the cellular phone when privacy is desired. The system announces, “Transfer call. Call transferred to privacy mode.” The system then ends the VR session. You can also issue the Transfer Call com- mand again to return to a hands-free call through the vehicle.


● “Mute” — Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.


4-74 Display screen, heater, air conditioner, audio and phone systems


NOTE:


If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature will be reset to “off” for the next call so the other party can hear your voice. “Phone book”


NOTE:


Phone book commands are not available when the vehicle is moving.


Main Menu


“Phone Book”


“New Entry” 䊊A “Edit” 䊊B “Delete” 䊊C “List Names” 䊊D


The Phone Book stores up to 40 names for each phone paired with the system. Each name can have up to 4 locations/phone numbers associ- ated with it.


NOTE: Each phone has its own separate phone book. You cannot access Phone A’s phone book if you are currently connected with Phone B. “New entry” 䊊A Use the New Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry. For example, say: “Mary.”


If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if the name sounds too much like a name already stored, the system tells you, then prompts you for a name again. Once the system accepts the name and you confirm it is correct, the system asks for a location (Home, Office, Mobile or Other). For example, say: “Home.”


The system acknowledges the location. The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory.


Enter a phone number by voice command:


For example, say: “five five five one two one two.” See “How to say numbers” in this section for more information.


To transfer a phone number stored in the cellular phone’s memory:


Say “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the Bluetooth姞 communication link. The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s also Manual can visit www.nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones.


for details. You


The system repeats the number and prompts you for the next command. When you have finished entering numbers or transferring an entry, choose “Store.”


The system confirms the name, location and number. The system then asks if you would like to store another location for the same name. If you do not wish to store another location, the system ends the VR session.


Display screen, heater, air conditioner, audio and phone systems 4-75


“Edit” 䊊B Use the Edit command to alter an existing phone book entry or to add a 2nd, 3rd or 4th phone number to an existing entry.


When prompted by the system, say the name of the entry you wish to edit.


The system acknowledges the name and asks you for the location you would like to edit.


Say the name of the location.


The system acknowledges the location.


The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory.


Enter a phone number by voice command:


For example, say: “five five five one two one two.” See “How to say numbers” in this section for more information.


To transfer a phone number stored in the cellular phone’s memory:


Say “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the Bluetooth姞 communication link.


The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s also Manual visit can www.nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones.


for details. You


The system repeats the number and prompts you for the next command. When you have finished entering numbers, choose “Store.”


The system confirms the name, location and number, then announces that the entry has been stored. The system then ends the VR session. “Delete” 䊊C Use the Delete command to erase one entry from the phone book, all entries from the phone book, the current redial number or the current call back number.


To delete entries from the phone book, say a name or “All entries” when prompted by the sys- tem.


The system acknowledges the command and asks you to confirm the deletion.


To delete the current redial number or call back number, say “redial number” or “call back num- ber” when prompted by the system.


4-76 Display screen, heater, air conditioner, audio and phone systems


If a redial number or a call back number exists, the system deletes them without asking for confirma- tion.


If there is no number for the entry you are trying to delete, the system says so and ends the VR session. “List names” 䊊D Use the List Names command to hear all the names and locations in the phone book.


The system recites the phone book entries but does not include the actual phone numbers. When the playback of the list is complete, the system goes back to the main menu.


You can stop the playback of the list at any time button on the steering by pressing the wheel. The system ends the VR session. “Memo pad”


Main Menu


“Memo Pad”


“Record” 䊊A “Play” 䊊B “Delete” 䊊C


The Memo Pad records a maximum of 6 voice memos, each up to 20 seconds long.


“Record” 䊊A The system announces “Recording” and a tone sounds, signaling you to begin.


Speak the information you wish to record clearly. When you are done, press the button on the steering wheel.


or


A tone sounds and the system announces “Memo recorded.” Another tone sounds to end the VR session.


If the memo pad is full, the system asks if you wish to record over the oldest memo. “Play” 䊊B The system plays back all the memos in the order of newest to oldest. The system ends the VR session.


If there are no memos recorded, the system an- nounces “No messages to play.” The system ends the VR session. “Delete” 䊊C The Delete command erases all memos. The system asks you to confirm this action before deleting all memos.


“Setup”


Main Menu


“Setup”


“Pair Phone” 䊊A “List Phone” 䊊B “Select Phone” 䊊C “Change Priority” 䊊D “Delete Phone” 䊊E “Select Ringtone” 䊊F “Bluetooth Off” 䊊G


Use the Setup command to change options as- sociated with the Bluetooth姞 Hands-Free Phone System. “Pair phone” 䊊A Use the Pair Phone command to pair a compat- ible phone to the Bluetooth姞 Hands-Free Phone System.


NOTE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Also, see “Pairing procedure” in this section for ad- ditional information.


Up to 5 phones can be paired. If you try to pair a sixth phone, the system announces that you must first delete one phone or replace an existing phone.


If you try to pair a phone that has already been paired to your vehicle’s system, the system an- nounces the name the phone is already using. The pairing procedure will then be cancelled.


When prompted by the system, choose from the following commands: ● “New phone” — Refer to “Pairing proce-


dure” in this section.


● “Replace phone” — The system announces the names of the phones already paired and asks which you would like to replace.


Once you say the name of the phone you wish to replace, the pairing procedure will begin. Refer to “Pairing procedure” in this section.


● “List phone” – See the description below. “List phone” 䊊B Use the List Phone command to hear the names of the phones currently paired. If no phones are paired, “No paired phones to list.” The system then ends the VR session.


the system announces,


Display screen, heater, air conditioner, audio and phone systems 4-77


“Select phone” 䊊C Use the Select Phone command to select a phone of lesser priority when two or more phones paired with Bluetooth姞 Hands-Free Phone Sys- tem are in the vehicle at the same time. The system asks you to name the phone and confirm the selection. Once the selection is confirmed, the selected phone remains active until the ignition switch is placed in the OFF position or you select a new phone. “Change priority” 䊊D Use the Change Priority command to change the priority level of the active phone. The priority level determines which phone is ac- tive when more than one paired Bluetooth姞 phone is in the vehicle. The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5). If the new priority level is already being used for another phone, the two phones will swap priority levels.


For example, if the current priority levels are:


Priority Level 1 = Phone A Priority Level 2 = Phone B Priority Level 3 = Phone C


and you change the priority level of Phone C to Level 1, then:


Priority Level 1 = Phone C Priority Level 2 = Phone B Priority Level 3 = Phone A


“Delete phone” 䊊E Use the Delete Phone command to delete a specific phone or all phones from the Bluetooth姞 Hands-Free Phone System. The system announces the names of the phones already paired with the system and their priority level. The system then gives you the option to delete a specific phone, all phones or listen to the list again. Once you choose to delete a phone or all phones, the system asks you to confirm this action.


NOTE: When you delete a phone, the associated phone book for that phone will also be deleted.


“Select ringtone” 䊊F Use the Select Ringtone command to select the tone heard in the vehicle when an incoming call is received. The system announces the name of the active phone and asks you to choose from the following commands: ● “Ringtone” — The system plays a ringtone and asks if you would like to select that tone. If you say “No”, the system plays the next ringtone available and continues to cycle through the ringtones until you select one or quit.


● “Silent” — The system asks you to confirm


your wish to disable the ringtone.


“Bluetooth off” 䊊G Use the Bluetooth Off command to turn off the Bluetooth姞 Hands-Free Phone System. When the Bluetooth姞 Hands-Free Phone Sys- tem is off, you will not be able to make or receive calls using NISSAN Voice Recognition. Also, you will not have access to the Phone Book. You can still use the Memo Pad and access Setup.


4-78 Display screen, heater, air conditioner, audio and phone systems


SPEAKER ADAPTATION (SA) MODE Speaker Adaptation allows up to two out-of- dialect users to train the system to improve rec- ognition accuracy. By repeating a number of commands, the users can create a voice model of their own voice that is stored in the system. The system is capable of storing a different speaker adaptation model for memory A and memory B.


If memory A is available, the system will use memory A to store the model. If memory A is in use and memory B is available, the system will use memory B to store the model. If both of the memory locations are in use, the system will ask the user to select which memory location should be overwritten. Training procedure The procedure for training a voice is as follows. 1. Position the vehicle in a reasonably quiet


outdoor location.


2. Sit in the driver’s seat with the engine run- ning, the parking brake on, and the transmis- sion in P (Park).


3. Press and hold the


than 5 seconds.


button for more


4. The


system announces:


PHONE/SEND (


“Press ) button for


hands-free phone system to enter the speaker adaptation mode or press the ) button to select a dif- PHONE/END ( ferent language.”


5. Press the


button.


For information on selecting a different lan- guage, see “Choosing a language” earlier in this section.


6. Voice memory A or memory B is selected automatically. If both memory locations are already in use, the system will prompt you to overwrite one. Follow the instructions pro- vided by the system.


7. When preparation is complete and you are


ready to begin, press the


button.


8. The SA mode will be explained. Follow the


instructions provided by the system.


9. When training is finished, the system will tell you an adequate number of phrases have been recorded.


10. The system will ask you to say your name. Follow the instructions to register your name.


The SA mode will stop if:


● The


button is pressed for more than 5


seconds in SA mode.


● The vehicle begins moving during SA mode. ● The ignition switch is placed in the OFF or


LOCK position. Training phrases During the SA mode, the system instructs the trainer to say the following phrases. (The system will prompt you for each phrase.) ● phone book new entry ● dial three oh four two nine ● delete call back number ● setup pair phone ● memo pad play ● eight pause nine three two pause seven ● delete all entries ● call seven two four zero nine ● phone book delete entry ● memo pad record ● dial star two one seven oh ● Yes


the the


11. The system will announce that speaker ad- aptation has been completed and the sys- tem is ready.


Display screen, heater, air conditioner, audio and phone systems 4-79


● setup main menu ● Delete ● dial nine seven two six six ● memo pad delete ● call seven six three oh one ● go back ● call five six two eight zero ● dial six six four three seven


● No ● select ring tone ● dial eight five six nine two ● Bluetooth on ● setup change priority ● call three one nine oh two ● nine seven pause pause three oh eight ● Cancel ● call back number ● call star two zero nine five ● delete phone ● dial eight three zero five one ● Home ● four three pause two nine pause zero ● delete redial number ● phone book list names ● call eight oh five four one ● Correction ● setup change ring tone ● dial seven four oh one eight 4-80 Display screen, heater, air conditioner, audio and phone systems


TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are en- countered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.


Symptom


System fails to interpret the command correctly.


The system consistently selects the wrong entry from the phone book.


Solution 1. Ensure that the command is valid. See “List of voice commands” in this section. 2. Ensure that the command is spoken after the tone. 3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle. 4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster on). NOTE: If it is too noisy to use the phone, it is likely that the voice commands will not be recognized. 5. If more than one command was said at a time, try saying the commands separately. 6. If the system consistently fails to recognize commands, the voice training procedure should be carried out to im- prove the recognition response for the speaker. See “Speaker Adaptation (SA) mode” in this section. 1. Ensure that the phone book entry name requested matches what was originally stored. This can be confirmed by using the “List Names” command. See “Phone book” in this section. 2. Replace one of the names being confused with a new name.


Display screen, heater, air conditioner, audio and phone systems 4-81


5 Starting and driving


Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2
Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2
Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3
Avoiding collision and rollover. . . . . . . . . . . . . . . . . . . . 5-6
Off-road recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Rapid air pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Drinking alcohol/drugs and driving. . . . . . . . . . . . . . . . 5-7
Driving safety precautions . . . . . . . . . . . . . . . . . . . . . . . 5-7
Ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Automatic transmission. . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Key positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
NISSAN Vehicle Immobilizer System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Before starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Driving the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Engine protection mode . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Automatic transmission. . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Cruise control (if so equipped) . . . . . . . . . . . . . . . . . . . . . 5-20


Precautions on cruise control . . . . . . . . . . . . . . . . . . . 5-20
Cruise control operations. . . . . . . . . . . . . . . . . . . . . . . 5-21
Break-in schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
Increasing fuel economy. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22


Using four wheel drive (4WD)


(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Transfer case shifting procedures . . . . . . . . . . . . . . . 5-24


Electronic locking rear differential (E-Lock) system (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Parking/parking on hills. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Brake precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31
Anti-lock Braking System (ABS). . . . . . . . . . . . . . . . . 5-32
Active brake limited slip (ABLS) system . . . . . . . . . . . . . 5-33
Vehicle Dynamic Control (VDC) system . . . . . . . . . . . . . 5-34
Rear sonar system (if so equipped) . . . . . . . . . . . . . . . . . 5-36
Cold weather driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Freeing a frozen door lock . . . . . . . . . . . . . . . . . . . . . . 5-37
Anti-freeze. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37
Draining of coolant water . . . . . . . . . . . . . . . . . . . . . . . 5-37
Tire equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37


Special winter equipment. . . . . . . . . . . . . . . . . . . . . . . 5-37
Driving on snow or ice . . . . . . . . . . . . . . . . . . . . . . . . . 5-37


Engine block heater (if so equipped) . . . . . . . . . . . . . 5-38


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.


● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.


EXHAUST GAS (carbon monoxide)


WARNING


● Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon monoxide is danger- ous. It can cause unconsciousness or death.


5-2 Starting and driving


● If you suspect that exhaust fumes are entering the vehicle, drive with all win- dows fully open, and have the vehicle inspected immediately.


● Do not run the engine in closed spaces


such as a garage.


● Do not park the vehicle with the engine running for any extended length of time. ● Keep the rear vent windows, lift gates, doors and trunk lids (if so equipped) closed while driving, otherwise exhaust gases could be drawn into the passen- ger compartment. If you must drive with one of follow these precautions: 1. Open all the windows.


these open,


2. Set the


air recirculation but- ton to off and the fan control dial to high to circulate the air.


● If electrical wiring or other cable con- nections must pass to a trailer through the seal on the lift gate or the body, follow the manufacturer’s recommen- dation to prevent carbon monoxide en- try into the vehicle.


● The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service. b. You suspect that exhaust fumes are passenger


into


the


entering compartment.


c. You notice a change in the sound of


the exhaust system.


d. You have had an accident involving damage to the exhaust system, un- derbody, or rear of the vehicle.


THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.


WARNING


● The exhaust gas and the exhaust sys- tem are very hot. Keep people, animals or flammable materials away from the exhaust system components.


● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


CAUTION


● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants.


● Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driv- ing if the engine misfires, or if notice- able loss of performance or other un- usual are detected. Have the vehicle inspected promptly by a NISSAN dealer.


conditions


operating


● Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the three-way catalyst.


● Do not race the engine while warming it


up.


● Do not push or tow your vehicle to start


the engine.


ON-PAVEMENT AND OFF-ROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles. They have higher ground clearance than passen- ger cars to make them capable of performing in a variety of on-pavement and off-road applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to per- form satisfactorily under off-road conditions. If at all possible, avoid sharp turns at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Be sure to read the driving safety precautions later in this section.


TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and in- flated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a signifi- cantly under-inflated tire causes the tire to over- heat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.


Starting and driving 5-3


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS mal- function indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approxi- mately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the mal- function exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alter- nate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replac- ing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.


5-4 Starting and driving


Additional information:


● The TPMS does not monitor the tire


pressure of the spare tire.


● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25
km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving).


● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After your tires are inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.


● The CHECK TIRE PRESSURE warning ap- pears in the vehicle information display when the low tire pressure warning light is illumi- nated and low tire pressure is detected. The CHECK TIRE PRESSURE warning turns off when the low tire pressure warning light turns off.


● The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction.


● Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illumi- nate. If the warning light illuminates in low ambient temperature, check the tire pres- sure for all four tires.


● You can also check the pressure of all tires (except the spare tire) on the display screen. The order of the tire pressure figures dis- played on the screen does not correspond with the actual order of the tire position. See “Tire pressure information” in the “Display screen, heater, air conditioner, audio and phone systems” section.


● The Tire and Loading Information label (also referred to as the vehicle placard or tire inflation pressure label) is located in the driver’s door opening.


For additional information, see “Low tire pressure warning light” in the “Instruments and controls” section, “Tire Pressure Monitoring System (TPMS)” in the “In case of emergency” section.


WARNING


● If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under- inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an acci- dent and could result in serious per- sonal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Informa- tion label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible. (See “Flat tire” in the “In case of emergency” section for changing a flat tire.)


● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.


● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.


● Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.


CAUTION


Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor reception of the signals from the tire pressure sensors, and the TPMS will not function properly.


Some devices and transmitters may temporarily interfere with the operation of the TPMS and cause the low tire pressure warning light to illu- minate.


Some examples are: – Facilities or electric devices using similar radio


frequencies are near the vehicle.


– If a transmitter set to similar frequencies is


being used in or near the vehicle.


– If a computer (or similar equipment) or a DC/AC converter is being used in or near the vehicle.


FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: 1. This device may not cause harmful in-


terference, and


2. This device must accept any interfer- ence received, including interference that may cause undesired operation. Note: Changes or modification not ex- pressly approved by the party respon- sible for compliance could void the us- er’s the equipment.


authority


operate


to


Starting and driving 5-5


For Canada:


This device complies with RSS-210 of In- dustry Canada. Operation is subject to the following two conditions:


1. This device may not cause interfer-


ence, and


2. This device must accept any interfer- ence, include interference that may cause undesired operation of the de- vice.


AVOIDING COLLISION AND ROLLOVER


WARNING


Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.


Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering ma- neuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and 5-6 Starting and driving


avoid driving when tired. Never drive when under the influence of alcohol or drugs (including pre- scription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual, and also instruct your passengers to do so.


Seat belts help reduce the risk of injury in colli- sions and rollovers. In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt. OFF-ROAD RECOVERY If the right side or left side wheels unintentionally leave the road surface, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic.


1. Remain calm and do not overreact.


2. Do not apply the brakes.


3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.


5.


4. When appropriate , slowly release the accel-


erator pedal to gradually slow the vehicle. If there is nothing in the way, steer the ve- hicle to follow the road while vehicle speed is reduced. Do not attempt to drive the ve- hicle back onto the road surface until vehicle speed is reduced.


6. When it is safe to do so, gradually turn the steering wheel until both tires return to the road surface. When all tires are on the road surface, steer the vehicle to stay in the ap- propriate driving lane.


● If you decide that it is not safe to return the vehicle to the road surface based on vehicle, road or traffic conditions, gradually slow the vehicle to a stop in a safe place off the road.


RAPID AIR PRESSURE LOSS Rapid air pressure loss or a “blow-out” can occur if the tire is punctured or is damaged due to hitting a curb or pothole. Rapid air pressure loss can also be caused by driving on under-inflated tires. Rapid air pressure loss can affect the handling and stability of the vehicle, especially at highway speeds.


Help prevent rapid air pressure loss by maintain- ing the correct air pressure and visually inspect the tires for wear and damage. See “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. If a tire rapidly loses air pressure or “blows-out” while driving, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the ve- hicle, road and traffic.


WARNING


The following actions can increase the chance of losing control of the vehicle if there is a sudden loss of tire air pressure. Losing control of the vehicle may cause a collision and result in personal injury. ● The vehicle generally moves or pulls in


the direction of the flat tire.


● Do not rapidly apply the brakes. ● Do not rapidly release the accelerator


pedal.


● Do not rapidly turn the steering wheel.


1. Remain calm and do not over react.


2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.


3. When appropriate, slowly release the accel-


erator pedal to gradually slow the vehicle.


4. Gradually steer the vehicle to a safe location off the road and away from traffic if possible.


5. Lightly apply the brake pedal to gradually


stop the vehicle.


6. Turn on the hazard warning flashers and either contact a roadside emergency service to change the tire or see “Changing a flat tire” in the “In case of emergency” section of this manual.


DRINKING ALCOHOL/DRUGS AND DRIVING


WARNING


Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.


NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Al- though the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that is true for drugs, too (over-the-counter, pre- scription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alco- hol, drugs, or some other physical condition. DRIVING SAFETY PRECAUTIONS Your NISSAN is designed for both normal and off-road use. However, avoid driving in deep wa- ter or mud as your NISSAN is mainly designed for leisure use, unlike a conventional off-road ve- hicle. Remember that two-wheel drive models are less capable than four-wheel drive models for rough road driving and extrication when stuck in deep snow or mud, or the like.


Starting and driving 5-7


Please observe the following precautions:


WARNING


● Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain.


● Do not drive across steep slopes. In- stead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.


● Many hills are too steep for any vehicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.


● Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle.


● Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.


5-8 Starting and driving


● If your engine stalls or you cannot make it to the top of a steep hill, never at- tempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear and apply brakes to control your speed.


● Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an acci- dent. Apply brakes lightly and use a low gear to control your speed.


● Unsecured cargo can be thrown around when driving over rough terrain. Prop- erly secure all cargo so it will not be thrown forward and cause injury to you or your passengers.


● Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than specified in this manual. This could cause your vehicle to roll over


● Do not grip the inside or spokes of the steering wheel when driving off-road. The steering wheel could move sud- denly and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim.


● Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.


● Lower your speed when encountering strong crosswinds. With a higher center of gravity, your NISSAN is more af- fected by strong side winds. Slower speeds ensure better vehicle control.


● Do not drive beyond the performance capability of the tires, even with 4WD engaged.


to raise two wheels off


● For 4WD equipped vehicles, do not at- tempt the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or unexpected ve- hicle movement which could result in serious vehicle damage or personal injury.


● Do not attempt to test a 4WD equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for emissions testing), or similar equipment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with 4WD before it is placed on a dynamometer. Using the wrong test equipment may result in drivetrain damage or unex- pected vehicle movement which could result in serious vehicle damage or per- sonal injury.


● Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.


● If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your NISSAN four-wheel drive vehicle has a higher center of gravity than a passenger car. The vehicle is not de- signed for cornering at the same speeds as passenger cars. Failure to operate this vehicle correctly could re- sult in loss of control and/or a rollover accident.


● Always use tires of the same type, size, brand, construction (bias, bias-belted, or radial), and tread pattern on all four wheels. Install tire chains on the rear wheels when driving on slippery roads and drive carefully.


● Be sure to check the brakes immedi- ately after driving in mud or water. See “Brake system” later in this section for “Wet brakes”.


● Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or sideways, you could be injured.


● Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See “Periodic mainte- nance” in the “NISSAN Service and Maintenance Guide.”


IGNITION SWITCH


WARNING


● Never remove the ignition key or place the ignition switch in the LOCK position while driving. The steering wheel will lock (for models without NISSAN ve- hicle immobilizer system). This may cause the driver to lose control of the vehicle and could result in serious ve- hicle damage or personal injury.


Starting and driving 5-9


To remove the key from the ignition switch:


1. Shift the shift selector to the P (Park) posi- tion with the ignition switch in the ON posi- tion.


2. Place the ignition switch in the LOCK posi-


tion.


3. Remove the key from the ignition switch.


If the shift selector is shifted to the P (Park) position after the ignition switch is placed in the OFF position or when the ignition switch cannot be placed in the LOCK position, proceed as follows to remove the key.


1. Move the shift selector into the P (Park)


position.


2. Place the ignition switch slightly toward the


ON position.


3. Place the ignition switch in the LOCK posi-


tion.


4. Remove the key.


The shift selector is designed so it cannot move out of P (Park) and into any of the other gear positions if the ignition switch is placed in the OFF position or if the key is removed from the switch.


The shift selector can be moved if the igni- tion switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ON positions. The OFF position is indicated by a “1” on the ignition switch. For models without NISSAN vehicle immo- bilizer system: when the ignition switch is in the OFF position, the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. To lock the steering wheel, turn the ignition to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left. If the key will not turn from the LOCK posi- tion, turn the steering wheel to the left or right while turning the key to unlock the key cylinder.


WSD0041


AUTOMATIC TRANSMISSION The ignition lock is designed so the ignition switch cannot be placed in the LOCK position and the key cannot be removed until the shift selector is moved to the P (Park) position. When removing the key from the ignition switch, make sure the shift selector is in the P (Park) position. If the shift selector is not returned to P (Park) position, the ignition switch cannot be placed in the LOCK position.


5-10 Starting and driving


1. Leave the ignition switch in the ON position


for approximately 5 seconds.


2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds.


3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.


If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices.


KEY POSITIONS LOCK: Normal parking position (0)


OFF: (Not used) (1)


ACC: (Accessories) (2)


This position activates electrical accessories such as the radio when the engine is not running.


ON: Normal operating position (3)


This position turns on the ignition system and the electrical accessories.


START: (4)


This position starts the engine. As soon as the engine has started, release the key. It automati- cally returns to the ON position. NISSAN VEHICLE IMMOBILIZER SYSTEM (if so equipped) The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.


If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures:


BEFORE STARTING THE ENGINE


● Make sure the area around the vehicle is


clear.


● Check fluid levels such as engine oil, cool- ant, brake fluid, and windshield-washer fluid as frequently as possible, or at least when- ever you refuel.


● Check that all windows and lights are clean. ● Visually inspect tires for their appearance and condition. Also check tires for proper inflation.


● Check that all doors are closed. ● Position seat and adjust head restraints. ● Adjust inside and outside mirrors. ● Fasten seat belts and ask all passengers to


do likewise.


● Check the operation of warning lights when the ignition switch is placed in the ON posi- tion. See “Warning/indicator lights and au- dible reminders” in the “Instruments and controls” section of this manual.


Starting and driving 5-11


STARTING THE ENGINE


DRIVING THE VEHICLE


1. Apply the parking brake.


2. Move the shift selector to P (Park) or N


(Neutral). P (Park) is recommended. The shift selector cannot be moved out of P (Park) and into any of the other gear positions if the ignition switch is turned to the OFF position or if the key is removed from the ignition switch. The starter is designed not to operate if the shift selector is in any of the driving positions.


3. Crank the engine with your foot off the accelerator pedal by placing the ignition switch in the START position. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. ● If the engine is very hard to start in ex- tremely cold weather or when restarting, depress the accelerator pedal a little (ap- proximately 1/3 to the floor) and hold it and then crank the engine. Release the key and the accelerator pedal when the engine starts.


● If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5 to 6 seconds. After


5-12 Starting and driving


cranking the engine, release the accel- erator pedal. Crank the engine with your foot off the accelerator pedal by turn- ing the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.


CAUTION


Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, otherwise the starter could be damaged.


4. Allow the engine to idle for at least 30 sec- onds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2–3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start.


ENGINE PROTECTION MODE The engine has an engine protection mode to reduce the chance of damage if the coolant tem- perature becomes too high (for example, when climbing steep grades in high temperature with heavy loads, such as when towing a trailer). When the engine temperature reaches a certain level: ● The engine coolant temperature gauge will


move toward the H position.


● Engine power may be reduced. ● The air conditioning cooling function may be automatically turned OFF for a short time (the blower will continue to operate).


Engine power and, under some conditions, ve- hicle speed will decrease. Vehicle speed can be controlled with the accelerator pedal, but the vehicle may not accelerate at the desired speed. The transmission will downshift or upshift as it reaches prescribed shift points. You can also shift manually. As driving conditions change and engine coolant temperature is reduced, vehicle speed can be increased using the accelerator pedal, and air conditioning cooling function will automatically be turned back ON.


If:


1. The engine coolant temperature is not re-


duced.


2. The air conditioning cooling function does


not turn back ON.


3. The engine oil pressure low/engine coolant illumi- temperature high warning light nates, this may indicate a malfunction. Move the vehicle off the road in a safe area and allow the engine to cool. If after checking the remains on, do not oil and coolant, the continue to drive and call a NISSAN dealer.


The malfunction indicator light (MIL) may also come ON. If only it remains on, you do not need to have your vehicle towed, but have it inspected soon by a NISSAN dealer. See “Malfunction in- dicator light (MIL)” in the “Instruments and con- trols ” section of this manual.


WARNING


AUTOMATIC TRANSMISSION


Overheating can result in reduced engine power and vehicle speed. The reduced speed may be lower than other traffic, which could increase the chance of a col- lision. Be especially careful when driving. If the vehicle cannot maintain a safe driv- ing speed, pull to the side of the road in a safe area. Allow the engine to cool and return to normal operation. See “If your vehicle overheats” in the “In case of emer- gency” section of this manual.


CAUTION


Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.


WARNING


● Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse), or L (Low). Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.


● Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.


● Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.


● Except in an emergency, do not shift to the N (Neutral) position while driving. Doing so can cause a loss of engine braking which may result in a collision, serious personal injury or death. In ad- dition, coasting with the transmission in the N (Neutral) position may cause serious damage to the transmission.


Starting and driving 5-13


The automatic transmission is designed so the foot brake pedal MUST be depressed before shifting from P (Park) to any drive position while the ignition switch is in the ON position. The shift selector cannot be moved out of the P (Park) position and into any of the other gear positions if the ignition switch is placed in the LOCK or OFF position.


CAUTION


● When stopping the vehicle on an uphill grade, do not hold the vehicle by de- pressing the accelerator pedal. The foot brake should be used for this purpose. ● Do not downshift abruptly on slippery roads. This may cause a loss of control.


The automatic transmission in your vehicle is electronically controlled to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the shift selector out of the P (Park) position.


2. Keep the foot brake pedal depressed and


move the shift selector into a driving gear.


3. Release the foot brake, then gradually start


the vehicle in motion.


5-14 Starting and driving


WSD0187


To move the shift selector:


: Shift while depressing the brake pedal


: Shift without depressing brake pedal


Shifting – console After starting the engine, fully depress the brake pedal and move the shift selector out of the P (Park) position.


WARNING


R (Reverse):


Apply the parking brake if the shift selec- tor is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage


If the key is turned to the OFF position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the key cannot be turned to the LOCK position and be removed from the ignition switch. Move the shift selector to the P (Park) position, then the key can be turned to LOCK. P (Park):


CAUTION


To prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.


Use the P (Park) shift selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal should be depressed to move the shift selector from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the shift selector into the P (Park) position.


CAUTION


To prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.


Use the R (Reverse) position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the shift selector from P (Park), N (Neutral) or any drive position to R (Reverse).


N (Neutral):


Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal forward driving. 4 (Fourth gear): Use this position for driving up and down long slopes where engine braking would be advanta- geous. Do not downshift into the 4 position at speeds over the following and do not exceed the follow- ing speeds in the 4 position.


4H: 62 MPH (100 km/h) 4LO: 31 MPH (50 km/h)


3 (Third gear): Use this position for driving up and down long slopes where engine braking would be advanta- geous. 2 (Second gear): Use this position for hill climbing or engine brak- ing on downhill grades. Do not downshift into the 2 position at speeds over the following and do not exceed the follow- ing speeds in the 2 position.


2WD and AUTO: 71 MPH (115 km/h) w/o tow mode 62 MPH (100 km/h) w/tow mode 4H: 62 MPH (100 km/h) w/o tow mode 62 MPH (100 km/h) w/tow mode


Starting and driving 5-15


4LO: 31 MPH (50 km/h) w/o tow mode 27 MPH (44 km/h) w/tow mode


1 (Low gear): Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. Do not downshift into the 1 position at speeds over the following and do not exceed the follow- ing speeds in the 1 position.


2WD and AUTO: 43 MPH (70 km/h) w/o tow mode 37 MPH (60 km/h) w/tow mode 4H: 43 MPH (70 km/h) w/o tow mode 37 MPH (60 km/h) w/tow mode 4LO: 19 MPH (30 km/h) w/o tow mode 16 MPH (27 km/h) w/tow mode


5-16 Starting and driving


WARNING


Apply the parking brake if the shift selec- tor is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.


If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the key cannot be turned to the LOCK position and be removed from the ignition switch. Move the shift selector to the P (Park) position, then the key can be turned to LOCK. P (Park):


To move the shift selector:


LSD0099


: Shift while depressing the brake pedal


CAUTION


: Shift without depressing brake pedal


Shifting – column After starting the engine, fully depress the brake pedal and move the shift selector out of the P (Park) position.


To prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.


Use the P (Park) shift selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal should be depressed to move the shift selector from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the shift selector into the P (Park) position.


R (Reverse):


CAUTION


To prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.


Use the R (Reverse) position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the shift selector from P (Park), N (Neutral) or any drive position to R (Reverse). N (Neutral): Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal forward driving.


M4 (Fourth):


For driving up or down long slopes where engine braking would be advantageous.


Shift ranges up or down one by one as follows: M1 ←→ M2 ←→ M3 ←→ M4
M4 will be displayed on the position indicator in the meter. M3 (Third):


Use for hill climbing or engine braking on downhill grades.


Shift ranges up or down one by one as follows: M1 ←→ M2 ←→ M3
M3 will be displayed on the position indicator in the meter. M2 (Second):


Use for hill climbing or engine braking on downhill grades.


Shift ranges up or down one by one as follows: M1 ←→ M2
M2 will be displayed on the position indicator in the meter.


Starting and driving 5-17


WSD0188


Manual shift mode When the manual shift mode button 䊊A is pressed while driving, the transmission enters the manual shift mode. Shift ranges can be selected manually.


In the manual shift mode, the shift range is dis- played on the position indicator in the meter. After pressing the manual shift mode button, the posi- tion indicator first displays M4 (Fourth)


Shift ranges up or down one by one as follows: M1←→ M2 ←→ M3 ←→ M4←→D


When canceling the manual shift mode: Press the manual shift mode button 䊊A to return the transmission to the normal driving mode. ● In the manual shift mode, the transmis- sion may not shift to the selected gear immediately because of vehicle speed. The transmission will up or down shift when vehicle speed matches the pro- grammed transmission shift points. This helps maintain driving perfor- mance and reduces the chance of ve- hicle damage or loss of control.


● In the manual shift mode, the transmis- sion will not up shift to a higher gear than is manually selected. When the vehicle speed decreases, the transmis- sion automatically shifts down and shifts to 1st gear before the vehicle comes to a stop.


M1 (First): Use this position when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. M1 will be displayed on the position indicator on the meter. ● Remember not to drive at high speeds for extended periods of time in lower than M4
range. This reduces fuel economy.


When shifting up: Move the shift selector to the + (up) side. (Shifts to higher range.) When shifting down: Move the shift selector to the ⫺ (down) side. (Shifts to lower range.) ● The transmission will automatically down- shift the gears. (For example, if you select the 3rd range, the transmission will shift down between the 3rd and 1st gears.)


● Moving the shift selector rapidly to the same side twice will shift the ranges in succession.


5-18 Starting and driving


LSD0090


Console shift


Shift lock release If the battery is discharged, the shift selector may not be moved from the P (Park) position even with the brake pedal depressed. To move the shift selector, release the shift lock. The shift selector can be moved to N (Neutral). However, for models without the NISSAN vehicle immobilizer system, the steering wheel will be locked unless the ignition switch is turned to the ON position. This allows the vehicle to be moved if the battery is discharged.


5. Use a protective cloth on the end of a small screwdriver before inserting it in the shift lock release slot and pushing down.


6. Move the shift selector to the N (Neutral) position while holding down the shift lock release.


7. For models without the NISSAN vehicle im- mobilizer system, turn the key to the ON position to unlock the steering wheel.


8. Now the vehicle may be moved to the de-


sired location.


If the shift selector cannot be moved out of P (Park), have a NISSAN dealer check the auto- matic transmission system as soon as possible.


WARNING


If the shift selector cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work. Malfunction- ing stop lights could cause an accident injuring yourself and others.


Accelerator downshift — in D position — For passing or hill climbing, depress the accel- erator pedal to the floor. This shifts the transmis- sion down into a lower gear, depending on the vehicle speed. Fail-safe When the fail-safe operation occurs, please note that the transmission will be locked in any of the forward gears according to the condition. If the vehicle is driven under extreme con- ditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition switch OFF and wait for 3 seconds. Then turn the ignition switch back to the ON position. The vehicle should return to its normal operating condition. If it does not return to its normal operating condition, have a NISSAN dealer check the transmis- sion and repair it if necessary.


Starting and driving 5-19


Column shift


LSD0101


To push the shift lock release, complete the fol- lowing procedure:


1. Turn the ignition key to the LOCK position


and remove the key


2. Apply the parking brake.


3. On vehicles equipped with a column shifter, tilt the steering wheel down to the lowest position.


4. Remove the shift


lock release cover as


shown.


PARKING BRAKE


CRUISE CONTROL (if so equipped)


WARNING


● Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident.


● Do not release the parking brake from


outside the vehicle.


● Do not use the shift selector in place of the parking brake. When parking, be sure the parking brake is fully engaged. ● Do not leave children unattended in a vehicle. They could release the parking brake and cause an accident.


5-20 Starting and driving


LSD0158
To engage: Firmly depress the parking brake. To release: 1. Firmly apply the foot brake. 2. Move the shift selector to the P (Park) posi-


tion.


3. Firmly depress the parking brake pedal and it


will release.


4. Before driving, be sure the brake warning


light goes out.


LSD0159


1. ACCEL/RES switch 2. COAST/SET switch 3. CANCEL switch 4. ON·OFF switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the vehicle information display then blinks to warn the driver, see “Vehicle infor- mation display” in the “Instruments and con- trols” section.


● If the SET indicator light blinks, push the cruise control ON·OFF switch off and have the system checked by a NISSAN dealer.


● The SET indicator light may blink when the cruise control ON·OFF switch is pushed ON while ACCEL/RES, COAST/SET, or CANCEL switch. To prop- erly set the cruise control system, use the following procedures.


pushing


the


WARNING


Do not use the cruise control when driving under the following conditions: ● When it is not possible to keep the


vehicle at a set speed.


● In heavy traffic or in traffic that varies in


speed.


● On winding or hilly roads. ● On slippery roads (rain, snow, ice, etc.). ● In very windy areas. Doing so could cause a loss of vehicle control and result in an accident.


CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed be- tween 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the ON·OFF switch on. The CRUISE indicator light in the vehicle information display will illuminate. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the vehicle information display will illuminate. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. ● To pass another vehicle, depress the ac- celerator pedal. When you release the pedal, the vehicle returns to the previously set speed.


● The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control.


To cancel the preset speed, use one of the following three methods. ● Push the CANCEL button; the SET indicator light in the vehicle information display goes out.


● Tap the brake pedal; the SET indicator light


goes out.


● Push the ON·OFF switch off. Both the CRUISE indicator light and SET indicator light in the vehicle information display go out. The cruise control is automatically canceled and the SET light in the vehicle information display goes out if: ● you depress the brake pedal while pushing the ACCEL/RES or SET/COAST switch. The preset speed is deleted from memory. ● the vehicle slows down more than 8 MPH


(13 km/h) below the set speed.


● you move the shift selector to N (Neutral). To reset at a faster cruising speed, use one of the following three methods. ● Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.


● Push and hold the ACCEL/RES switch. When the vehicle attains the speed you de- sire, release the switch.

Loading...
x