2011 Nissan Titan Owners Manual

the RSS is not turned off, it may indicate a mal- function in the RSS. Keep the RSS sensors (located on the rear bumper fascia) free from snow, ice and large accumulations of dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the RSS.

● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground.

● If your vehicle sustains damage to the rear bumper leaving it mis- aligned or bent, the sensing zone may be altered causing inaccurate measure- ment of obstacles or false alarms.

fascia,

The Rear Sonar System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the shift selector is in R (Reverse). The system may not detect objects at speeds above 3
mph (5 km/h) and may not detect certain angular or moving objects.

The RSS detects obstacles up to 5.9 feet (1.8 m) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the RSS detects a station- ary or receding object further than 10 inches (25.0 cm) from the side of the vehicle, the tone

COLD WEATHER DRIVING

FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply de- icer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole or use the remote keyless entry keyfob (if so equipped). ANTI-FREEZE In the winter when it is anticipated that the tem- perature will drop below 32°F (0°C), check the anti-freeze to assure proper winter protection. For details, see “Engine cooling system” in the “Maintenance and do-it-yourself” section of this manual. BATTERY If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maxi- mum efficiency, the battery should be checked regularly. For details, see “Battery” in the “Main- tenance and do-it-yourself” section of this manual.

DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pave- ment. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your ve- hicle on snowy or icy roads, NISSAN recom- mends the use of MUD & SNOW or ALL SEASON TIRES on all four wheels. Please consult a NISSAN dealer for the tire type, size, speed rating and availability informa- tion.

2. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.

Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. 3. Tire chains may be used. For details see “Tire chains” in the “Maintenance and do-it- yourself” section of this manual.

Starting and driving 5-37

SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: ● A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.

● A sturdy, flat board to be placed under the

jack to give it firm support.

● A shovel to dig the vehicle out of snowdrifts. ● Extra washer fluid to refill the windshield-

washer fluid reservoir.

DRIVING ON SNOW OR ICE

WARNING

● Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet the road is salted or sanded.

ice until

● Whatever the condition, drive with cau- tion. Accelerate and slow down with care. If accelerating or downshifting too fast, the drive wheels will lose even more traction.

5-38 Starting and driving

● Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement.

● Allow greater following distances on

slippery roads.

● Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reach- ing it. Try not to brake while on the ice, and avoid steering maneuvers.

sudden

any

● Do not use the cruise control on slip-

pery roads.

● Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.

ENGINE BLOCK HEATER (if so equipped)

WARNING

● Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. You can be se- riously injured by an electrical shock if you use an ungrounded connection.

● Disconnect and properly store the en- gine block heater cord before starting the engine. Damage to the cord could result in an electrical shock and can cause serious injury.

● Use a heavy-duty 3-wire, 3-pronged ex- tension cord rated for at least 10 A. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110-VAC outlet. Failure to use the proper extension cord or a grounded outlet can result in a fire or electrical shock and cause serious personal injury.

Engine block heaters are available through NISSAN dealers to assist in cold temperature starting. The engine block heater should be used when the outside temperature is 20° F (-7° C) or lower.

To use the engine block heater:

1. Turn the engine off.

2. Open the hood and unwrap the engine block

heater cord.

3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord.

4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110- volt AC (VAC) outlet.

5. The engine block heater must be plugged in for at least 2 - 4hours, depending on outside temperatures, to properly warm the engine coolant. Use an appropriate timer to turn the engine block heater on.

6. Before starting the engine, unplug and prop- erly store the cord to keep it away from moving parts.

Starting and driving 5-39

MEMO

5-40 Starting and driving

6 In case of emergency

Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-2
Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Towing your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Towing recommended by NISSAN . . . . . . . . . . . . . . 6-12
Vehicle recovery (freeing a stuck vehicle) . . . . . . . . . 6-13

FLAT TIRE

TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, and the CHECK TIRE PRESSURE warning appears in the vehicle information display, one or more of your tires is significantly under-inflated. If equipped, the sys- tem also displays pressure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. If the vehicle is being driven with low tire pressure, the TPMS will activate and warn you of it by the low tire pressure warning light. This system will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). For more details, refer to “Warning/indicator lights and audible reminders” in the “Instruments and controls” section, “Tire pressure information” in the “Display screen, heater, air conditioner, audio and phone systems” section and “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section.

6-2 In case of emergency

WARNING

● If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under- inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an acci- dent and could result in serious per- sonal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Informa- tion label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible.

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

● Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.

CHANGING A FLAT TIRE If you have a flat tire, follow the instructions be- low: Stopping the vehicle 1. Safely move the vehicle off the road and

away from traffic.

2. Turn on the hazard warning flashers.

3. Park on a level surface and apply the parking

brake. Move the shift selector to P (Park).

4. Turn off the engine.

5. Raise the hood to warn other traffic and to signal professional road assistance person- nel that you need assistance.

6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.

WARNING

● Make sure the parking brake is securely applied and the automatic transmission is shifted into P (Park).

● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.

● Never change tires if oncoming traffic is close to your vehicle. Wait for profes- sional road assistance.

Getting the spare tire and tools 1. Fold up the rear bench seat. Refer to “Fold- ing the rear bench seat” in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual.

WCE0044

Blocking wheels Place suitable blocks 䊊1 at both the front and back of the wheel diagonally opposite the flat tire 䊊2 to prevent the vehicle from moving when it is jacked up.

WARNING

Be sure to block the wheel as the vehicle may move and result in personal injury.

In case of emergency 6-3

LCE0093
2. Unscrew and remove the jack and tool kit.

WCE0150
3. Assemble the two pieces of the jack rod. Find the oval-shaped opening above the middle of the license plate. Pass the T-shaped end of the jack rod through the opening and direct it toward the spare tire winch, located directly above the spare tire.

CAUTION

Do not insert the jack rod straight as it is designed to be inserted at an angle as shown.

WCE0151
4. Fit the square end of the jack rod into the square hole of the wheel nut wrench to form a handle.

5. Seat the T-shaped end of the jack rod into the T-shaped opening of the tire winch. Ap- ply pressure to keep the jack rod engaged in the spare tire winch and turn the jack rod counterclockwise to lower the spare tire.

6. Once the spare tire is completely lowered, reach under the vehicle, remove the retainer chain, and carefully slide the tire from under the rear of the vehicle.

6-4 In case of emergency

CAUTION

Be sure to center the spare tire suspend- ing plate on the wheel and then lift the spare tire.

Jacking up vehicle and removing the damaged tire

WARNING

● Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands.

● Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change. ● Use the correct jack-up points. Never use any other part of the vehicle for jack support.

● Never jack up the vehicle more than

necessary.

● Never use blocks on or under the jack.

● Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for slip differentials.

vehicles

limited

with

● Do not allow passengers to stay in the

vehicle while it is on the jack.

● Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move.

Always refer to the illustration for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.

In case of emergency 6-5

2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. The jack-up points are indicated by stamped ar- rows on the side of the frame.

6-6 In case of emergency

WCE0152
The jack should be used on firm and level ground.

3.

LCE0087
Install the assembled jack rod into the jack as shown.

4. To lift the vehicle, securely hold the jack lever and rod. Carefully raise the vehicle until the tire clears the ground.

5. Remove the wheel nuts and then remove the

tire.

4. Lower

the vehicle slowly until

the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated. Lower the ve- hicle completely.

WARNING ● Incorrect wheel nuts or

improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.

● Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.

● Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque:

98 ft-lb (133 N·m)

WCE0063

Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading “Wheels and tires” in the “Mainte- nance and do-it-yourself” section of this manual.

1. Clean any mud or dirt from the surface be-

tween the wheel and hub.

2. Carefully put the spare tire on and tighten

the wheel nuts finger tight.

3. With the wheel nut wrench, tighten wheel nuts alternately and evenly as illustrated until they are tight.

The wheel nuts must be kept tightened to specification at all is recom- mended that wheel nuts be tightened to specifications at each lubrication interval.

times.

It

Adjust tire pressure to the COLD pressure.

COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km).

COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar.

After adjusting tire pressure to the COLD tire pressure, the display (if so equipped) of the tire pressure information may show higher pressure than the COLD tire pres- sure after the vehicle has been driven more than 1 mile (1.6 km). This is because the tire pressure increases as the tire temperature rises. This does not indicate a system mal- function.

5. Securely store the flat tire and jacking equip-

ment in the vehicle.

In case of emergency 6-7

● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.

● Do not attempt to jump start a frozen battery. It could explode and cause se- rious injury.

JUMP STARTING

To start your engine with a booster battery, the instructions and precautions below must be fol- lowed.

WARNING

● If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.

● Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.

● Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a cor- rosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with anything, imme- diately flush the contacted area with water.

● Keep battery out of

children.

the reach of

● The booster battery must be rated at 12
volts. Use of an improperly rated battery can damage your vehicle.

WARNING

● Always make sure that the spare tire and jacking equipment are properly se- cured after use. Such items can become dangerous projectiles in an accident or sudden stop.

● The spare tire is designed for emer- gency use. See specific instructions un- der the heading “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual.

6-8 In case of emergency

WARNING

Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury.

1.

If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other. Do not allow the two vehicles to touch.

2. Apply the parking brake. Move the shift se- lector to P (Park). Switch off all unnecessary electrical systems (lights, heater, air condi- tioner, etc.).

WCE0054
3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.

4. Connect jumper cables in the sequence il-

lustrated (䊊A , 䊊B , 䊊C , 䊊D ).

CAUTION

● Always connect positive (⫹) to positive (⫹) and negative (⫺) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery.

● Make sure the jumper cables do not touch moving parts in the engine com- partment and that the cable clamps do not contact any other metal.

5. Start the engine of the booster vehicle and

let it run for a few minutes.

6. Keep the engine speed of the booster ve- hicle at about 2,000 rpm, and start the en- gine of the vehicle being jump started.

CAUTION

Do not keep the starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.

7. After starting the engine, carefully discon- nect the negative cable and then the positive cable.

8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.

In case of emergency 6-9

PUSH STARTING

IF YOUR VEHICLE OVERHEATS

WARNING

WARNING

Do not push start this vehicle. The three- way catalyst may be damaged.

CAUTION

Automatic transmission models cannot be push-started or tow-started. Attempt- ing to do so may cause transmission damage.

6-10 In case of emergency

● Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire.

● To avoid the danger of being scalded, never remove the radiator or coolant reservoir cap while the engine is still hot. When the radiator or coolant reser- voir cap is removed, pressurized hot water will spurt out, possibly causing serious injury.

● Do not open the hood if steam is com-

ing out.

If your vehicle is overheating (indicated by an extremely high temperature gauge reading and the illumination of the engine oil pressure/engine coolant temperature high indicator light), or if you feel a lack of engine power, detect abnormal noise, etc. take the following steps. 1. Move the vehicle safely off the road, apply the parking brake and move the shift selector to P (Park). Do not stop the engine.

2. Turn off the air conditioner. Open all the windows, move the heater or air conditioner temperature control to maximum hot and fan control to high speed.

3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or cool- ant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen.

4. Open the engine hood.

WARNING

If steam or water is coming from the en- gine, stand clear to prevent getting burned.

5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running. The radiator hoses and radiator should not leak water. If coolant is leaking, the water pump belt is missing or loose, or the cooling fan does not run, stop the en- gine.

WARNING

Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or get caught in, engine belts or the engine cooling fan. The engine cooling fan can start at any time.

6. After the engine cools down, check the cool- ant level in the engine coolant reservoir tank with the engine running. Add coolant to the engine coolant reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer.

TOWING YOUR VEHICLE

When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could dam- age your vehicle. Towing instructions are avail- able from a NISSAN dealer. Local service opera- tors are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions:

WARNING

● Never ride in a vehicle that is being

towed.

● Never get under your vehicle after it has

been lifted by a tow truck.

CAUTION

● When towing, make sure that the trans- mission, axles, steering system and powertrain are in working condition. If any of these conditions apply, dollies or a flatbed tow truck must be used.

● Always attach safety chains before

towing.

For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” sec- tion of this manual.

In case of emergency 6-11

If the speed or distance must necessarily be greater, remove the propeller shaft before towing to prevent damage to the transmission.

Two-wheel drive models NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground or place the vehicle on a flat bed truck as illustrated.

CAUTION

● Never

tow automatic transmission models with the rear wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the front wheels raised always use towing dollies under the rear wheels.

● When towing automatic transmission models with the front wheels on the ground or on towing dollies: – Place the ignition switch in the OFF position and secure the steering wheel in a straight-ahead position with a rope or similar device. Never secure the steering wheel by placing the ignition switch in the LOCK posi- tion. This may cause damage to the lock mechanism (if so equipped).

TOWING RECOMMENDED BY NISSAN

ACE1019

6-12 In case of emergency

Four-wheel drive models NISSAN recommends that towing dollies be used when towing your vehicle or place the ve- hicle on a flat bed truck as illustrated.

CAUTION

Never tow 4WD models with any of the wheels on the ground as this may cause serious and expensive damage to the transfer case and transmission.

WCE0161

LCE0083
VEHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle

WARNING

To avoid vehicle damage, serious per- sonal injury or death when recovering a stuck vehicle: ● Contact a professional towing service to recover the vehicle if you have any questions recovery procedure.

regarding

the

In case of emergency 6-13

5. Slowly rock the vehicle forward and back-

ward. ● Shift back and forth between R (Reverse)

and D (Drive).

● Apply the accelerator as little as possible

to maintain the rocking motion.

● Release the accelerator pedal before

shifting between R and D.

● Do not spin the tires above 35 mph (55
km/h) or above 12 mph (20 km/h) if the E–Lock System is engaged.

6.

If the vehicle cannot be freed after a few tries, contact a professional towing service to remove the vehicle.

● Attach recovery devices only to main structural members of the vehicle or the recovery hooks.

● Do not use the vehicle tie-downs to tow

or free a stuck vehicle.

● Only use devices specifically designed for vehicle recovery and follow the manufacturer’s instructions.

● Always pull the recovery device straight out from the front of the vehicle. Never pull at an angle.

● Route recovery devices so they do not touch any part of the vehicle except the attachment point.

If your vehicle is stuck in sand, snow, mud, etc., use a tow strap or other device designed specifi- cally for vehicle recovery. Always follow the manufacturer’s instructions for the recovery de- vice. Do not use the tie-down hooks for towing or vehicle recovery.

Rocking a stuck vehicle

WARNING

● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.

If your vehicle is stuck in sand, snow, mud, etc., use the following procedure: 1. Turn off the Vehicle Dynamic Control (VDC)

system.

2. Activate the Electronic Locking Rear Differ-

ential (E-Lock) System (if so equipped).

3. Make sure the area in front and behind the

vehicle is clear of obstructions.

4. Turn the steering wheel right and left to clear

an area around the front tires.

6-14 In case of emergency

7 Appearance and care

Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Aluminum alloy wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Chrome parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Tire dressings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Cleaning interior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Air fresheners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Floor mats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Corrosion protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Most common factors contributing to vehicle corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Environmental factors influence the rate of corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
To protect your vehicle from corrosion . . . . . . . . . . . . 7-6

CLEANING EXTERIOR

In order to maintain the appearance of your ve- hicle, it is important to take proper care of it.

To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage

from acid rain.

● after driving on coastal roads. ● when contaminants such as soot, bird drop- pings, tree sap, metal particles or bugs get on the paint surface.

● when dust or mud builds up on the surface. Whenever possible, store or park your vehicle inside a garage or in a covered area.

When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water. 7-2 Appearance and care

CAUTION

● Do not use car washes that use acid in the detergent. Some car washes, espe- cially brushless ones, use some acid for cleaning. The acid may react with some plastic vehicle components, causing them to crack. This could affect their appearance, and also could cause them not to function properly. Always check with your car wash to confirm that acid is not used.

● Do not wash the vehicle with strong household soap, strong chemical deter- gents, gasoline or solvents.

● Avoid using tight-napped or

● Do not wash the vehicle in direct sun- light or while the vehicle body is hot, as the surface may become water-spotted. rough cloths, such as washing mitts. Care must removing caked-on dirt or other foreign sub- stances so the paint surface is not scratched or damaged.

taken when

be

Rinse the vehicle thoroughly with plenty of clean water.

Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to

the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. Polishing is recommended to remove built-up wax residue and to avoid a weathered appearance before re-applying wax. A NISSAN dealer can assist you in choosing the proper product. ● Wax your vehicle only after a thorough wash- ing. Follow the instructions supplied with the wax.

● Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.

Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks.

REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. UNDERBODY In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the un- derbody and suspension. Before the winter pe- riod and again in the spring, the underseal must be checked and, if necessary, retreated. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.

CAUTION

When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electri- cal conductors, radio antenna elements or rear window defroster elements.

ALUMINUM ALLOY WHEELS Wash the wheels regularly with a sponge damp- ened in a mild soap solution, especially during winter months in areas where road salt is used. If not removed, road salt can discolor the wheels.

CAUTION

Follow the directions below to avoid staining or discoloring the wheels: ● Do not use a cleaner that uses strong acid or alkali contents to clean the wheels.

● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as am- bient temperature.

● Rinse the wheel to completely remove the cleaner within 15 minutes after the cleaner is applied.

CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish. TIRE DRESSINGS NISSAN does not recommend the use of tire dressings. Tire manufacturers apply a coating to the tires to help reduce discoloration of the rub- ber. If a tire dressing is applied to the tires, it may react with the coating and form a compound. This compound may come off the tire while driving and stain the vehicle paint. If you choose to use a tire dressing, take the following precautions: ● Use a water-based tire dressing. The coat- ing on the tire dissolves more easily than with an oil-based tire dressing.

● Apply a light coat of tire dressing to help prevent tire tread/grooves (where it would be difficult to remove).

from entering

the

it

● Wipe off excess tire dressing using a dry towel. Make sure the tire dressing is com- pletely removed from the tire tread/grooves. ● Allow the tire dressing to dry as recom- mended by the tire dressing manufacturer.

Appearance and care 7-3

CLEANING INTERIOR

Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth damp- ened in mild soap solution, then wipe clean with a dry, soft cloth. Regular care and cleaning is required in order to maintain the appearance of the leather. Before using any fabric protector, read the manu- facturer’s recommendations. Some fabric pro- tectors contain chemicals that may stain or bleach the seat material. Use a cloth dampened only with water to clean the meter and gauge lens.

WARNING

Do not use water or acidic cleaners (hot steam cleaners) on the seat. This can damage the seat or occupant classifica- tion sensor. This can also affect the opera- tion of the air bag system and result in serious personal injury.

7-4 Appearance and care

CAUTION

● Never use benzine, thinner or any simi-

lar material.

● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, polishes, oils, cleaning fluids, solvents, deter- gents or ammonia-based cleaners as they may damage the leather’s natural finish.

● Never use fabric protectors unless rec-

ommended by the manufacturer.

● Do not use glass or plastic cleaner on meter or gauge lens covers. It may dam- age the lens cover.

AIR FRESHENERS Most air fresheners use a solvent that could affect the vehicle interior. If you use an air freshener, take the following precautions: ● Hanging-type air fresheners can cause per- manent discoloration when they contact ve- hicle interior surfaces. Place the air fresh- ener in a location that allows it to hang free and not contact an interior surface.

● Liquid-type air fresheners typically clip on the vents. These products can cause imme- diate damage and discoloration when spilled on interior surfaces.

Carefully read and follow the manufacturer’s in- structions before using the air fresheners. FLOOR MATS

WARNING

To avoid potential pedal interference that may result in a collision or injury: ● NEVER place a floor mat on top of an- front

in the driver

floor mat

other position.

● Use only genuine NISSAN floor mats specifically designed for use in your ve- hicle model. See your NISSAN dealer for more information.

● Properly position the mats in the floor- well using the floor mat positioning aid. See ⴖFloor mat positioning aidⴖ in this section.

The use of genuine NISSAN floor mats can ex- tend the life of your vehicle carpet and make it easier to clean the interior. Mats should be main- tained with regular cleaning and replaced if they become excessively worn.

SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual.

WARNING

Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these materials may severely weaken the seat belt webbing.

CORROSION PROTECTION

MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION ● The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.

● Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.

ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand, dirt and water on the ve- hicle body underside can accelerate corrosion. Wet floor coverings will not dry completely inside the vehicle and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated in areas of high relative humidity, especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used.

Appearance and care 7-5

LAI0009

Floor mat positioning aid This vehicle includes two driver’s side front floor mat brackets and one passenger’s side front floor mat bracket to help keep your floor mats in place. Genuine NISSAN floor mats have been specially designed for your vehicle model. The driver’s side floor mat has two grommet holes incorporated in it and the passenger’s side has one grommet hole. Position each mat by placing the floor mat bracket hook through the floor mat grommet holes while centering the mat in the floorwell. Periodically check to make certain the mats are properly positioned.

Temperature High temperatures accelerate the rate of corro- sion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use acceler- ates the corrosion process. Road salt also accel- erates the disintegration of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION ● Wash and wax your vehicle often to keep the

vehicle clean.

● Always check for minor damage to the paint

and repair it as soon as possible.

● Keep drain holes at the bottom of the doors

open to avoid water accumulation.

● Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible.

CAUTION

● NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.

● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them.

Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, the underbody must be cleaned periodically. For additional protection against rust and corro- sion, which may be required in some areas, con- sult a NISSAN dealer.

7-6 Appearance and care

8 Maintenance and do-it-yourself

Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Explanation of general maintenance items . . . . . . . . . 8-2
Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Engine compartment check locations . . . . . . . . . . . . . . . . 8-6
Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Checking engine coolant level . . . . . . . . . . . . . . . . . . . 8-8
Changing engine coolant . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Engine oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Checking engine oil level . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Changing engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Changing engine oil filter . . . . . . . . . . . . . . . . . . . . . . . 8-11
5-speed automatic transmission fluid . . . . . . . . . . . . . . . 8-11
Power steering fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Windshield-washer fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Windshield-washer fluid reservoir . . . . . . . . . . . . . . . 8-13
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Variable voltage control system. . . . . . . . . . . . . . . . . . . . . 8-15
Drive belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
Spark plugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Replacing spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
In-cabin microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Windshield wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22
Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . 8-23
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Keyfob (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 8-25
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26
Fog lights (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 8-26
Exterior and interior lights. . . . . . . . . . . . . . . . . . . . . . . 8-28
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31
Tire pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32
Tire labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36
Types of tires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38
Tire chains. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39
Changing wheels and tires . . . . . . . . . . . . . . . . . . . . . 8-39

MAINTENANCE REQUIREMENTS

GENERAL MAINTENANCE

Your NISSAN has been designed to have mini- mum maintenance requirements with long ser- vice intervals to save you both time and money. However, some day-to-day and regular mainte- nance is essential to maintain your NISSAN’s good mechanical condition, as well as its emis- sions and engine performance.

It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.

As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the mainte- nance chain. Scheduled maintenance

For your convenience, both required and optional scheduled maintenance items are described and listed in your “NISSAN Service and Maintenance Guide”. You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance

General maintenance includes those items which should be checked during normal day-to-day op- eration. They are essential for proper vehicle op- eration. It is your responsibility to perform these maintenance procedures regularly as prescribed. 8-2 Maintenance and do-it-yourself

Performing general maintenance checks requires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by you, a qualified technician, or, if you prefer, a NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and corrected by a NISSAN dealer. NISSAN technicians are well-trained specialists who are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN ve- hicles before they work on your vehicle, rather than after they have worked on it. You can be confident that a NISSAN dealer’s service department performs the best job to meet the maintenance requirements on your vehicle — in a reliable and economical way.

During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have a NISSAN dealer do it promptly. In addition, you should notify a NISSAN dealer if you think that repairs are required.

When performing any checks or maintenance work, closely observe the “Maintenance precau- tions” later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with “ * ” isfound later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood Check that the doors and engine hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, latch pins, rollers and links as necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released.

When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Tires* Check the pressure with a gauge often and always prior to long distance trips. If neces- sary, adjust the pressure in all tires, including the spare, to the pressure specified. Check carefully for damage, cuts or excessive wear. Tire Pressure Monitoring System (TPMS) transmitter components Replace the TPMS transmitter grommet seal, valve core and cap when the tires are replaced due to wear or age. Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel

alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. ● For additional

information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.

Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other damage. Have a dam- aged windshield repaired by a qualified repair facility. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when per- forming periodic maintenance, cleaning the ve- hicle, etc. Additional information on the following items with an “*” is found later in this sec- tion.

Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not bind or require uneven effort. Keep the floor mat away from the pedal.

Automatic transmission P (Park) position mechanism On a fairly steep hill check that your vehicle is held securely with the shift selector in the P (Park) position without applying any brakes. Brake pedal Check the pedal for smooth opera- tion. If the brake pedal suddenly goes down fur- ther than normal, the pedal feels spongy or the vehicle seems to take longer to stop, see a NISSAN dealer immediately. Keep the floor mat away from the pedal. Brakes Check that the brakes do not pull the vehicle to one side when applied. Parking brake Check the parking brake opera- tion regularly. The vehicle should be securely held on a fairly steep hill with only the parking brake applied. If the parking brake needs adjustment, see a NISSAN dealer. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched positions. Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt web- bing for cuts, fraying, wear or damage.

Maintenance and do-it-yourself 8-3

etc., that may have accumulated. Make sure the hoses have no cracks, deformation, rot or loose connections. Underbody The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thor- oughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the “Appearance and care” section of this manual. Windshield-washer fluid* Check that there is adequate fluid in the reservoir.

Steering wheel Check for changes in the steer- ing system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Under the hood and vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). Battery* Check the fluid level It should be between the MAX and MIN lines. Ve- hicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Brake fluid level* Make sure that the brake fluid level is between the MIN and MAX lines on the reservoir. Engine coolant level* Check the coolant level when the engine is cold. 8-4 Maintenance and do-it-yourself

in each cell.

Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait more than 10 minutes for the oil to drain back into the oil pan. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by a NISSAN dealer. See the carbon monoxide warning in the “Starting and driving” section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected imme- diately. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves,

MAINTENANCE PRECAUTIONS

When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed.

WARNING

● Park the vehicle on a level surface, ap- ply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector to P (Park)

● Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.

● If you must work with the engine run- ning, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.

● It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle.

● Always wear eye protection whenever

you work on your vehicle.

● If you must run the engine in an en- closed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.

● Never get under the vehicle while it is supported only by a jack. If it is neces- sary to work under the vehicle, support it with safety stands.

● Keep smoking materials,

flame and sparks away from the fuel tank and battery.

● On gasoline engine models, the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.

CAUTION

● Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.

● Avoid contact with used engine oil and coolant. Improperly disposed engine oil, engine coolant and/or other vehicle fluids can damage the environment. Al- ways conform to local regulations for disposal of vehicle fluid.

● Never leave the engine or automatic transmission related component har- nesses disconnected while the ignition switch is in the ON position.

● Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position.

This “Maintenance and do-it-yourself” section gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN service manual is also avail- able. See “Owner’s Manual/Service Manual or- der information” in the “Technical and consumer information” section of this manual. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer.

Maintenance and do-it-yourself 8-5

ENGINE COMPARTMENT CHECK LOCATIONS

8-6 Maintenance and do-it-yourself

WDI0630

Battery Fuse/fusible link box Transmission dipstick Engine oil filler cap Brake fluid reservoir

1. 2. 3. 4. 5. 6. Windshield-washer fluid reservoir 7. 8. 9. 10. Power steering fluid reservoir 11. Engine oil dipstick 12. Engine coolant reservoir NOTE: Engine cover removed for clarity.

Air cleaner Drive belt location Radiator cap

ENGINE COOLING SYSTEM

The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The antifreeze solution con- tains rust and corrosion inhibitors. Additional en- gine cooling system additives are not necessary.

WARNING

● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down. Serious burns could be caused by high pressure fluid escaping from the radiator. See precautions in “If your vehicle overheats” found in the “In case of emergency” section of this manual. ● The radiator is equipped with a pres- sure type radiator cap. To prevent en- gine damage, use only a genuine NISSAN radiator cap.

CAUTION

(blue)

● When adding or replacing coolant, be sure to use only Genuine NISSAN Long Life Antifreeze/Coolant or equivalent. Genuine NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to provide antifreeze protection to -34° F (-37° C). If additional freeze protec- tion is needed due to weather where you operate your vehicle, add Genuine NISSAN Long Life Antifreeze/Coolant (blue) concentrate following the direc- tions on the container. If an equivalent coolant other than Genuine NISSAN Long Life Antifreeze/Coolant (blue) is used, follow the coolant manufacturer’s instructions to maintain minimum anti- freeze protection to -34° F (-37° C). The use of other types of coolant solutions other than Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent may damage the engine cooling system.

● The life expectancy of the factory-fill coolant is 105,000 miles (168,000 km) or 7 years. Mixing any other type of cool- ant other than Genuine NISSAN Long Life Antifreeze/Coolant (blue), includ- ing Genuine NISSAN Long Life Antifreeze/Coolant (green), or the use of non-distilled water will reduce the life expectancy of the factory-fill cool- ant. Refer to the Nissan Service and Maintenance Guide for more details.

Maintenance and do-it-yourself 8-7

● Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

● Keep coolant out of the reach of chil-

dren and pets.

Engine coolant must be disposed of properly. Check your local regulations.

the use of non-distilled water will reduce the life expectancy of the factory-fill coolant. Refer to the NISSAN Service and Maintenance Guide for more details. The engine coolant reservoir is a pressur- ized tank. When installing the cap, tighten it until a clicking sound is heard. If the cooling system frequently requires coolant, have it checked by a NISSAN dealer. CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing.

WARNING

● To avoid the danger of being scalded, never change the coolant when the en- gine is hot.

● Never remove the radiator or engine coolant reservoir cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

LDI0369

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir up to the MAX level. This vehicle contains Genuine NISSAN Long Life Antifreeze/Coolant (blue). The life expectancy of the factory-fill coolant is 105,000 miles (168,000
km) or 7 years. Mixing any other type of coolant or 8-8 Maintenance and do-it-yourself

ENGINE OIL

CAUTION

Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty.

LDI0370

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature.

3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil pan.

4. Remove the dipstick and wipe it clean. Re-

insert it all the way.

LDI0371
5. Remove the dipstick again and check the oil level. It should be between the H (High) and L (Low) marks 䊊B . This is the normal oper- ating oil level range. If the oil level is below the L (Low) mark 䊊A , remove the oil filler cap and pour recommended oil through the opening. Do not overfill 䊊C .

6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.

Maintenance and do-it-yourself 8-9

If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” in this section.

● Waste oil must be disposed of prop-

erly.

● Check your local regulations.

WARNING

● Prolonged and repeated contact with used engine oil may cause skin cancer. ● Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

● Keep used engine oil out of reach of

children.

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force.

WDI0504

CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature, then turn it off.

3. Remove the oil filler cap 䊊A by turning it

counterclockwise.

4. Place a large drain pan under the drain plug

䊊B .

5. Remove the drain plug 䊊B with a wrench by turning it counterclockwise and completely drain the oil.

8-10 Maintenance and do-it-yourself

Drain plug tightening torque: 22 - 29 ft-lb (29 - 39 N·m)

and

“Capacities

7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. See recommended fuel/lubricants” in the “Technical and con- sumer information” section of this manual for drain and refill capacity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.

8. Start the engine. Check for leakage around the drain plug and oil filter. Correct as re- quired.

9. Turn the engine off and wait more than 10
minutes. Check the oil level with the dipstick. Add engine oil if necessary.

5-SPEED AUTOMATIC TRANSMISSION FLUID

5. Wipe the engine oil filter sealing surface with

a clean rag.

When checking or replacement is required, we recommend your NISSAN dealer for servicing.

CAUTION

CAUTION

Be sure to remove any old gasket material remaining on the sealing surface of the engine. Failure to do so could lead to an oil leak and engine damage.

6. Coat the gasket on the new filter with clean

engine oil.

7. Screw on the oil filter until a slight resistance

is felt, then tighten an additional 2/3 turn.

8. Start

the engine and check for leakage

around the oil filter. Correct as required.

9. Turn the engine off and wait more than 10
minutes. Check the oil level. Add engine oil if necessary.

● Use Genuine NISSAN Matic S ATF. If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used.

● Using automatic transmission fluid other than Genuine NISSAN Matic S ATF or Matic J ATF will cause deteriora- tion in driveability and automatic trans- mission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle lim- ited warranty.

The specified automatic transmission fluid is also described on caution labels located in the engine compartment.

Maintenance and do-it-yourself 8-11

WDI0505

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply

the parking brake.

2. Turn the engine off. 3. Place a large drain pan under the oil filter 䊊A . filter 4. Loosen the oil wrench by turning it counterclockwise. Then remove the oil filter by turning it by hand.

filter 䊊A with an oil

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

POWER STEERING FLUID

BRAKE FLUID

CAUTION

● DO NOT OVERFILL. ● Recommended

is NISSAN PSF or equivalent.

fluid

Genuine

WDI0256
The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122° - 176°F (50° - 80°C) or using the COLD MAX range on the power steering fluid reservoir at fluid tempera- tures of 32° - 86°F (0° - 30°C). If the fluid is at or below the MIN line, add Genu- ine NISSAN PSF to HOT MAX or COLD MAX depending on system fluid temperature. Remove the cap and fill through the opening.

8-12 Maintenance and do-it-yourself

to

For further brake fluid specification information, refer recommended fuel/lubricants” in the “Technical and consumer information” section of this manual.

“Capacities

and

WARNING

● Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehi- cle’s stopping ability.

● Clean the filler cap before removing. ● Brake fluid is poisonous and should be stored carefully in marked containers out of reach of children.

CAUTION

Do not spill the fluid on any painted sur- faces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

WINDSHIELD-WASHER FLUID

LDI0374

WDI0405

BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer.

WINDSHIELD-WASHER FLUID RESERVOIR Fill the windshield-washer fluid reservoir periodi- cally. Add windshield-washer fluid when the low windshield-washer fluid warning light comes on (if so equipped).

To fill the windshield-washer fluid reservoir, lift the cap off the reservoir and pour the windshield- washer fluid into the reservoir opening.

Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield- washer antifreeze. Follow the manufacturer’s in- structions for the mixture ratio.

Refill the reservoir more frequently when driving conditions require an increased amount of windshield-washer fluid. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.

CAUTION

for windshield-washer

● Do not substitute engine anti-freeze coolant fluid. This may result in damage to the paint. ● Do not fill the windshield-washer fluid reservoir with washer fluid concen- trates at full strength. Some methyl al- cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield- washer fluid reservoir.

● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the windshield-washer fluid reser- voir. Do not use the windshield-washer fluid reservoir to mix the washer fluid concentrate and water.

Maintenance and do-it-yourself 8-13

● Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion.

● When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.

● Battery posts, terminals and related ac- cessories contain lead and lead com- pounds. Wash hands after handling.

● Keep battery out of

children.

the reach of

● Do not tip the battery. Keep the vent

caps tight and the battery level.

WDI0224
1. Remove the vent caps with a screwdriver as shown. Use a cloth to protect the battery case.

BATTERY

● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water.

● Make certain the terminal connections are

clean and securely tightened.

● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.

WARNING

● Do not expose the battery to flames, an electrical spark or a cigarette. Hydro- gen gas generated by the battery is ex- plosive. Explosive gases can cause blindness or injury. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. Sulfuric acid can cause blindness or injury. After touch- ing a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.

8-14 Maintenance and do-it-yourself

VARIABLE VOLTAGE CONTROL SYSTEM

Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.

WDI0566

CAUTION

● Do not ground accessories directly to the battery terminal. Doing so will by- pass the variable voltage control sys- tem and the vehicle battery may not charge completely.

● Use electrical accessories with the en- gine running to avoid discharging the vehicle battery.

Your vehicle is equipped with a variable voltage control system. This system measures the amount of electrical discharge from the battery and controls voltage generated by the generator.

Maintenance and do-it-yourself 8-15

2. Check the fluid level

in each cell.

WDI0529
If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill. Reinstall the vent caps.

DRIVE BELT

The current sensor 䊊A is located near the battery along the negative battery cable. If you add elec- trical accessories to your vehicle, be sure to ground them to a suitable body ground such as the frame or engine block area.

WARNING

Be sure the ignition switch is in the OFF or LOCK position before servicing drive belt. The engine could rotate unexpectedly.

1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer.

2. Have the belt checked regularly for condi- tion and tension in accordance with the maintenance the “NISSAN Service and Maintenance Guide”.

schedule

found