2011 Nissan Titan Owners Manual

Download PDF Manual
the “Safety — Seats, seat belts and supplemental restraint system” section of this manual. High beam indicator light (blue) This blue light comes on when the headlight high beams are on and goes out when the low beams are selected. The high beam indicator light also comes on when the passing signal is activated. Malfunction Indicator Light (MIL) If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction. The Malfunction Indicator Light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 gallons (11.4 liters) of fuel in the fuel tank. light should After a few driving trips, the turn off if no other potential emission control system malfunction exists. If this indicator light comes on steady for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control sys- tem inspection/maintenance test. See “Readi- ness for inspection/maintenance (I/M) test” in the “Technical and consumer information” section of this manual. Operation The Malfunction Indicator Light will come on in one of two ways: ● Malfunction Indicator Light on steady — An emission control system malfunction has been detected. Check the fuel-filler cap if the LOOSE FUEL CAP warning appears in the vehicle information display. If the fuel- filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. light should turn off after a few The driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. ● Malfunction Indicator Light blinking — An engine misfire has been detected which may damage the emission control system. To re- duce or avoid emission control system dam- age: – do not drive at speeds above 45 MPH (72 km/h). – avoid hard acceleration or deceleration. – avoid steep uphill grades. – if possible, reduce the amount of cargo being hauled or towed. The Malfunction Indicator Light may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. Instruments and controls 2-19 CAUTION Continued vehicle operation without hav- ing the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system. Security indicator light (if so equipped) This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational. For additional tems” later in this section. information, see “Security sys- Slip indicator light This indicator will blink when the VDC system or the traction control system is operating, thus alerting that the vehicle is nearing its traction limits. The road surface may be slippery. Turn signal/hazard indicator lights The appropriate light flashes when the turn signal switch is activated. 2-20 Instruments and controls Both lights flash when the hazard switch is turned on. Vehicle Dynamic Control (VDC) off indicator light This indicator light comes on when the Vehicle Dynamic Control off switch is pushed to OFF, the transfer case is in the 4LO position ( model), or when the Vehicle Dynamic Control system is not functioning properly. This indicates the Vehicle Dynamic Control system is not oper- ating. Push the Vehicle Dynamic Control off switch again or restart the engine and the system will operate normally. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” sec- tion of this manual. The Vehicle Dynamic Control light also comes on when you place the ignition switch in the ON position. The light will turn off after about 2 sec- onds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the Vehicle Dynamic Control system checked by a NISSAN dealer. While the Vehicle Dynamic Control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal. The VDC system will be disabled and the VDC light will illuminate when the electronic locking rear differential (E-lock) system switch (if so equipped) is turned on and the E-lock system is engaged. If the E-lock system disengages or the switch is turned off, the VDC system will be enabled and the VDC light will turn off. AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime A chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch placed in the OFF posi- tion, a chime sounds when the driver’s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leav- ing the vehicle. VEHICLE INFORMATION DISPLAY (if so equipped) WIC1248 The vehicle information display 䊊1 is located to the left of the speedometer. It displays such items as: ● automatic transmission position indicator ● cruise control system information (if so equipped) ● some indicators and warnings WIC1249 HOW TO USE THE VEHICLE INFORMATION DISPLAY Press the vehicle information display INFO but- ton 䊊1 located on the instrument panel to toggle through the following modes. MPG → Range → Warning Rotate the INFO button 䊊2 to highlight the de- sired menu option within the selected mode. Press the INFO button 䊊1 to enter the high- lighted menu. The icons at the bottom of the display screen show the options available: ENTER — Press the INFO button to select a highlighted option. NEXT — Rotate the INFO button to high- light an option. Instruments and controls 2-21 WIC1166 Warning mode (if so equipped) The warning mode can be selected to view any warnings that may be present. Once the screen is selected you have the option of skipping the warning or viewing it in detail. Warnings can be present for issues such as an open door or low fuel. For more information about potential warnings, see “Vehicle information dis- play warnings and indicators” later in this section. 2-22 Instruments and controls Vehicle information display warnings and indicators 1. Door open warning 2. Low fuel warning 3. Low windshield-washer fluid warning 4. Parking brake warning 8. 4WD shift indicator ( model) 5. Cruise main switch indicator (if so equipped) 9. Automatic transmission position indicator 6. Cruise set switch indicator (if so equipped) 10. Loose fuel cap warning 7. Transfer 4LO position indicator ( model) 11. Check tire pressure warning LIC2006 Instruments and controls 2-23 Door open warning This warning illuminates when a door has been opened and the engine is running. Low fuel warning This warning illuminates when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small re- serve of fuel in the tank when the fuel gauge needle reaches E (Empty). Low windshield-washer fluid warning This warning illuminates when the windshield- washer fluid is at a low level. Add windshield- washer fluid as necessary. See “Windshield- washer fluid” in the “Maintenance and do-it- yourself” section of this manual. Parking brake warning This warning illuminates when the parking brake is set and the vehicle is driven. Cruise main switch indicator (if so equipped) This indicator illuminates when the cruise control main switch is pushed. The indicator turns off when the main switch is pushed again. When the cruise main switch indicator the cruise control system is operational. 2-24 Instruments and controls illuminates, Cruise set switch indicator (if so equipped) This indicator illuminates while the vehicle speed is controlled by the cruise control system. If the indicator blinks while the engine is running, it may indicate the cruise control system is not function- ing properly. Have the system checked by a NISSAN dealer. Transfer 4LO position indicator ( model) This indicator illuminates when the 4WD shift switch is set in the 4LO position with the ignition switch placed in the ON position. If the 4WD shift switch is set in the 4LO position and the indicator blinks, stop the vehicle, drive slowly forward and the indicator will turn on. When you shift between 4H and 4LO, stop the vehicle, move the shift selector to the N (Neutral) position, then depress and turn the 4WD shift switch to 4LO or 4H. The transfer case may be damaged if you shift the switch while driving. You cannot move the transfer 4WD shift switch between 4H and 4LO unless you have first stopped the vehicle and moved the shift selector to N (Neutral). Make sure the transfer 4LO posi- tion indicator illuminates when you shift the 4WD shift switch to 4LO. The indicator may blink while shifting from one drive mode to the other. 4WD shift indicator ( model) While the engine is running, the 4WD shift indi- cator will illuminate the position selected by the 4WD shift switch. The 4WD shift indicator may blink while shifting from one drive mode to the other. Automatic transmission position indicator When the ignition switch is placed in the ON position, this indicator shows the shift selector position. See “Driving the vehicle” in the “Starting and driving” section of this manual. Loose fuel cap warning This warning appears when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. See “Fuel-filler cap” in the “Pre-driving checks and adjustments” section. Check tire pressure warning This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected. If this warning appears, stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. See “Low tire pressure warning light” earlier in this section and “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section. SECURITY SYSTEMS (if so equipped) LIC0644 Your vehicle may have two types of security sys- tems: ● Vehicle security system (if so equipped) ● NISSAN Vehicle Immobilizer System (if so equipped) VEHICLE SECURITY SYSTEM (if so equipped) The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs. The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Al- ways secure your vehicle even if parking for a brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible. Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. How to arm the vehicle security system 1. Close all windows. (The system can be armed even if the windows are open.) 2. Remove the from the ignition switch. 3. Close all doors. Lock all doors. The doors can be locked with the key, power door lock switch (if the door is opened, locked and then closed), or with the keyfob. Instruments and controls 2-25 Keyfob operation: ● Push the button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. ● When the button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a re- minder that the doors are already locked. The horn may or may not beep. Refer to “Silencing the horn beep feature” (vehicles without navigation system) in the “Pre- driving checks and adjustments” section or “Vehicle electronic systems” (vehicles with navigation system) in the “Display screen, heater, air conditioner, audio and phone sys- tems” section. 4. Confirm that the indicator light comes on. The light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the ve- hicle security system automatically shifts light begins into the armed phase. The to flash once every 3 seconds. If, during the 30-second pre-arm time period, the door is unlocked by the key or the keyfob, or the ignition switch is placed to ACC or ON, the system will not arm. 2-26 Instruments and controls ● If the key is turned slowly when locking the door, the system may not arm. Fur- thermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is re- moved. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again. ● Even when the driver and/or passengers are in the vehicle, the system will arm with all doors closed and locked with the ignition switch in the OFF position. ● The lockable bedside storage com- partment (if so equipped) is not pro- tected by the vehicle security system. Vehicle security system activation The vehicle security system will give the following alarm: ● The headlights blink and the horn sounds intermittently. ● The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver’s door with the key or by pressing the button on the keyfob. The alarm is activated by: ● opening a door without using the key or keyfob (even if the door is unlocked by using the inside lock knob or the power door lock switch). How to stop an activated alarm The alarm stops only by unlocking the driver’s button door with the key or by pressing the on the keyfob. NISSAN VEHICLE IMMOBILIZER SYSTEM (if so equipped) The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures: 1. Leave the ignition switch in the ON position for approximately 5 seconds. 2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds. 3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key. If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY — IMMOBILIZER, ANT ASSY — IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RE- SPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPER- ATE THE EQUIPMENT. WINDSHIELD WIPER AND WASHER SWITCH LIC0474 LIC0965 Security indicator light The security indicator light blinks whenever the ignition switch is placed in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition switch is placed in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser- vice as soon as possible. Please bring all registered keys that you have when visiting your NISSAN dealer for service. SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position. Push the lever down to operate the wiper at the following speed: 䊊1 Intermittent (INT) — intermittent operation can be adjusted by turning the knob toward 䊊A (Slower) or 䊊B (Faster). Also, the inter- mittent operation speed varies in accor- dance with the vehicle speed. (For example, when the vehicle speed is high, the intermit- tent operation speed will be faster.) Instruments and controls 2-27 NOTE: You can turn on or turn off the driving speed dependent intermittent wiper func- tion for vehicles with navigation system. Refer to “Vehicle electronic systems” in the “Display screen, heater, air conditioner, au- dio and phone systems” section later in this manual. 䊊2 Low (LO) — continuous low speed operation 䊊3 High (HI) — continuous high speed opera- tion Push the lever up 䊊4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you 䊊5 to operate the washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield. CAUTION ● Do not operate the washer continu- ously for more than 30 seconds. ● Do not operate the washer if the reser- voir tank is empty. ● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water. 2-28 Instruments and controls REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH Type A LIC0488 To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster light on the switch comes on. Push the switch again to turn the defroster off. indicator The rear window defroster automatically turns off after approximately 15 minutes. HEADLIGHT AND TURN SIGNAL SWITCH LIC1173 LIC1158 SIC2745 Type B NOTE: If the rear power window (if so equipped) is lowered while the defroster switch is on, the rear window defroster will automati- cally shut off. The heated outside mirrors (if so equipped) will remain on. The rear win- dow defroster will automatically turn on when the rear power window is fully closed if the switch is on. Type C CAUTION When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster. Type A HEADLIGHT CONTROL SWITCH Lighting 䊊1 When turning the switch to the posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊2 When turning the switch to the posi- tion, the headlights come on and all the other lights remain on. Instruments and controls 2-29 WIC1250 SIC3019 Type C Type B CAUTION Use the headlights with the engine run- ning to avoid discharging the vehicle battery. WIC1251 Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: ● Turn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark. ● Turn off all the lights when it is light. ● Keep all the lights on for 45 seconds after you place the ignition switch in the OFF position and all doors are closed. 2-30 Instruments and controls To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi- tion 䊊1 . 2. Place the ignition switch in the ON position. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is placed in the OFF position and a door is opened and left open, the headlights remain ON for 5 minutes. If another door is opened during the 5 minutes, then the 5 minute timer is reset. To turn the autolight system off, turn the switch to the OFF, position. , or LIC0836 Be sure you do not put anything on top of the autolight sensor 䊊1 located on the top side of the instrument panel. The autolight sensor controls the autolight; if it is cov- ered, the autolight sensor reacts as if it is dark out and the headlights will illuminate. If this occurs while parked with the engine off and the ignition switch placed in the ON position, your vehicle’s battery could be- come discharged. WIC1252 Headlight beam select 䊊1 To select the high beam function, push the lever forward. The high beam lights come on and the light illuminates. 䊊2 Pull the lever back to select the low beam. 䊊3 Pulling and releasing the lever flashes the headlight high beams on and off. Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the or 5 minutes. position, the headlights will turn off after Instruments and controls 2-31 If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is placed in the OFF position. WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others. WIC1506 INSTRUMENT BRIGHTNESS CONTROL The instrument brightness control operates when the in or AUTO position (with auto- the lights activated). Turn the control to adjust the brightness of instru- ment panel lights when driving at night. headlight control switch is After the headlights automatically turn off with the position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position position. and then turned to the or or CAUTION Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the position. Turn the OFF position or in the headlight switch to the position for full illumination when driving at night. 2-32 Instruments and controls WIC1253 TURN SIGNAL SWITCH Turn signal 䊊1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically. Lane change signal 䊊2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch. WIC1254 FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the To turn the fog lights on with the headlight switch in the AUTO position (if so equipped), the head- lights must be on, then turn the fog light switch to the To turn the fog lights off, turn the fog light switch to the OFF position. position. position. The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected. Instruments and controls 2-33 HAZARD WARNING FLASHER SWITCH CARGO LAMP SWITCH (if so equipped) The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road. ● Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic. ● Turn signals do not work when the haz- ard warning flasher lights are on. 2-34 Instruments and controls LIC0616 To turn on the cargo lamp, push the switch down to the ON position. The tailgate lights (if so equipped) will also illuminate when the cargo lamp switch is in the ON position. CAUTION Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, otherwise the battery will go dead. HORN HEATED SEAT (if so equipped) LIC0604 To sound the horn, push the center pad area of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury. WIC1441 The front seats are warmed by built-in heaters. 1. Start the engine. 2. Push the LO or HI position of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on. 3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off. CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. ● Any liquid spilled on the heated seat should be removed immediately with a dry cloth. ● When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials. ● If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer. ● The battery could run down if the seat heater is operated while the engine is not running. Instruments and controls 2-35 VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped) WIC0534 The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driv- ing conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn on the system. See “Vehicle Dy- namic Control (VDC) system” in the “Starting and driving” section. 2-36 Instruments and controls indicator will come on. LIC0729 The Electronic Locking Rear Differential (E-Lock) system can help provide added traction if the vehicle is stuck or becoming stuck. To activate the E-Lock system: ● the 4WD switch must be in the 4LO position (4-wheel drive vehicles), ● the vehicle must be stopped or moving at 4 mph (7 km/h) or less, and ● the E-Lock system switch must be turned ON. When the E-Lock switch is turned ON, the indi- cator light will flash until the system engages. However, if all operation conditions listed above are not met or the system becomes disengaged, the indicator light will continue to flash. The Anti-Lock Brake (ABS) system is disabled and the ABS light illuminates when the E-Lock system is ON. Also, the Vehicle Dynamic Control (VDC) system is disabled and the VDC light illuminates when the E-Lock system is ON. See “Electronic locking rear differential (E-Lock) system” in the “Starting and Driving” section for further explanation and system limitations. WARNING ● Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After us- ing the E-Lock system to free the ve- hicle, turn the system OFF. ● Use the E-Lock system only when free- ing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice sur- face. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the ve- hicle during engine braking, accelerat- ing or turning, which may result in an accident and serious personal injury. CAUTION ● After using the E-Lock system, turn the switch OFF to prevent possible damage to driveline components from extended use. ● Do not drive over 12 MPH (20 km/h) when the system is engaged. Doing so could result in possible damage to the driveline. ● Do not turn on the E-lock system while the tires are spinning. Doing so could damage drivetrain components. REAR SONAR SYSTEM OFF SWITCH (if so equipped) LIC0471 WARNING The rear sonar system is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly. The rear sonar system is active when the ignition switch is placed is placed to the ON position and the shift selector is in R (Reverse). When sensors detect obstacles within 5.9 ft (1.8 m) of the rear bumper, a beeping tone is emitted. The rear sonar system can be disabled by push- ing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. Push the switch again to enable the system. The indicator light will go off. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section. Instruments and controls 2-37 TOW MODE SWITCH POWER OUTLET For additional information, refer to “Tow mode” in the “Technical and consumer information” sec- tion later in this manual. Front row WIC1404 LIC0594 Tow mode should be used when pulling a heavy trailer or hauling a heavy load. Driving the vehicle in the tow mode with no trailer/load or light trailer/light load will not cause any damage. How- ever, fuel economy may be reduced, and the transmission/engine driving characteristics may feel unusual. Press the tow mode switch to activate tow mode. The indicator light on the tow mode switch illumi- nates when tow mode is selected. Press the tow mode switch again to turn tow mode OFF. Tow mode is automatically canceled when the ignition switch is placed in the OFF position. 2-38 Instruments and controls 2nd row (if so equipped) WIC0643 LIC0618 Inside center armrest (if so equipped) The power outlets are for powering electrical accessories such as cellular telephones. The power outlets located on the driver’s side of the instrument panel and in the truck box are powered directly by the vehicle’s battery. The power outlets located on the passenger’s side of the instrument panel, inside the center armrest, and in the 2nd row are powered only when the ignition switch is placed in the ACC or ON position. Open the cap to use a power outlet. CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information. ● Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. ● Use power outlets with the engine run- ning to avoid discharging the vehicle battery. ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. ● When not in use, be sure to close the cap. Do not allow water or any other liquid to contact the outlet. Instruments and controls 2-39 STORAGE LIC0617 LIC0565 LIC0566 Center tray (if so equipped) CONSOLE BOX (if so equipped) In truck box (if so equipped) Do not use the outlet located in the truck box with accessories that exceed 12 volt, 120W (15A) power draw . Do not use double adapters or more than one electrical accessory. CAUTION For the power outlet located in the bed of the truck, do not use with accessories that exceed a 12 volt, 120W (15A) power draw. Do not use double adapters or more than one electrical accessory. Side tray INSTRUMENT PANEL STORAGE TRAYS WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop. The rubber mats can be removed for cleaning. 2-40 Instruments and controls Console box storage trays LIC1369 LIC1370 LIC1371 Console box storage Pull up on the lever 䊊1 to open the console box lid 䊊2 . Console box lock Use the master key to lock 䊊1 or unlock 䊊2 the console box. Instruments and controls 2-41 CENTER ARMREST STORAGE (if so equipped) To access the center armrest storage area, lower the center armrest and lift the lid. 2-42 Instruments and controls LIC0621 LIC0578 GLOVE BOX Open the glove box by pulling the handle. Use the master key to lock or unlock the glove box lock (if so equipped). The valet key cannot be used. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC0567 SUNGLASSES HOLDER (if so equipped) To open the sunglasses holder, push and release. WARNING ● Keep the sunglasses holder closed while driving to prevent an accident. MAP POCKETS LIC0589 Instruments and controls 2-43 LIC0575 SEATBACK POCKET (if so equipped) The seatback pocket is located on the back of the driver’s seat. The pocket can be used to store maps. Small bin (if so equipped) OVERHEAD CONSOLE (if so equipped) LIC0568 LIC0569 Medium bin (if so equipped) Storage bins WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Push the button to open a storage bin. Push the lid up to close. 2-44 Instruments and controls LIC1372 LIC0620 LIC1373 Front — Type A Front — Type B CUP HOLDERS CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. Adjustable (if so equipped) Position the arm on the adjustable cup holder so that the cup is held securely. Instruments and controls 2-45 LIC0622 LIC0554 LIC0556 Armrest (if so equipped) 2nd row (rear of front console) (if so equipped) To open the 2nd row cup holders (rear of front console), lower the lid. To close, raise the lid. 2nd row bench (if so equipped) 2-46 Instruments and controls Bottle holder — Type A Bottle holder — Type B LIC0558 LIC0624 CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid containers. LIC0626 GROCERY HOOKS (if so equipped) The grocery hooks allow for standard size plastic grocery bags to hang side by side. To access the grocery hooks, fold up the rear bench seat. See “Folding the rear bench seat” in the “Safety — Seats, seat belts and supplemental restraint system” section earlier in this manual. CAUTION Do not apply a total load of more than 18 lbs (8 kg) to a single grocery hook. Instruments and controls 2-47 WINDOWS CAUTION POWER WINDOWS (if so equipped) ● Do not store a total load of more than 22 storage inside the (10 lbs kg) compartment. ● Do not use the storage compartment or storage compartment lid as a step. Do- ing so may damage them. LIC0625 LOCKABLE BEDSIDE STORAGE COMPARTMENT (if so equipped) To access the bedside storage compartment, hold the key hole cover open and insert the master key. Turn the key clockwise to unlock the lid. The tray inside the bedside storage compartment is adjustable. The bedside storage compartment will automati- cally lock when the lid is closed. You do not need to use the key. 2-48 Instruments and controls WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents. The power windows operate when the ignition switch is placed in the ON position, or for about 45 seconds after the ignition switch is placed in the OFF position. If the driver’s or passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled. Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch. WIC0845 1. Window lock button 2. 3. 4. 5. 6. Power door lock switch Front passenger side automatic switch Right rear passenger window switch Left rear passenger window switch Driver side automatic switch LIC0580 Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window. To open the window, push the switch and hold it down 䊊1 . To close the window, pull the switch up 䊊2 . Instruments and controls 2-49 Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs. WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window. the dealer If the vehicle’s battery is disconnected, replaced, or jump started, the power window auto-reverse function may not operate properly. If this occurs, please contact to re-initialize the power window auto-reverse system. If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately low- ered. LIC0581 LIC0410 Rear power window switch The rear power window switches open or close only the corresponding windows. To open the window, push the switch and hold it down 䊊1 . To close the window, pull the switch up 䊊2 . Locking passengers’ windows When the window lock button is depressed, only the driver’s side window can be opened or closed. Push it again to cancel the window lock function. Automatic operation To fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening. To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held. To stop the window, press the switch down while the window is closing. 2-50 Instruments and controls WIC0263 MANUAL WINDOWS (if so equipped) The side windows can be opened or closed by turning the hand crank on each door. LIC0627 LIC1553 REAR SLIDING WINDOW (if so equipped) Squeeze the handles of the lever 䊊1 , then slide the window open 䊊2 . REAR POWER WINDOW SWITCH (if so equipped) To open the rear power window, push in and hold the switch. To close the rear power window, pull out and hold the switch. To stop the opening or closing function at any time, simply release the switch. Instruments and controls 2-51 MOONROOF (if so equipped) NOTE: If the rear power window (if so equipped) is lowered while the defroster switch is on, the rear window defroster will automati- cally shut off. The heated outside mirrors (if so equipped) will remain on. The rear win- dow defroster will automatically turn on when the rear power window is fully closed if the switch is on. WIC0812 AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position. The auto- matic moonroof is operational for about 45 sec- onds, even if the ignition switch is placed in the ACC or OFF position. If the driver’s door or the front passenger’s door is opened during this period of about 45 seconds, power to the moon- roof is canceled. Sliding the moonroof To fully open the moonroof, push the switch to- ward the open position 䊊3 . 2-52 Instruments and controls To fully close the moonroof, push the switch toward the close position 䊊4 . To open or close the moonroof part way, push the switch in any direction 䊊5 while the moonroof is sliding open or closed to stop it in the desired position. Tilting the moonroof To tilt the moonroof up, push the tilt switch to- ward the up position 䊊1 . To tilt the moonroof down, push the tilt switch toward the down position 䊊2 . Restarting the moonroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electri- cal supply interrupted and/or some abnormality detected. Use the following reset procedure to return moonroof operation to normal. 1. If the moonroof lid is open, push the tilting switch repeatedly toward the down position 䊊2 to fully close the lid. 2. Push and hold the tilting switch for more than 2 seconds toward the down position 䊊2 to reestablish the lid’s home position. The moonroof should now operate normally. Auto-reverse function (when closing or tilting down the moonroof) The auto-reverse function can be activated when the moonroof is closed or tilted down by auto- matic operation when the ignition switch is placed in the ON position or for about 45 sec- onds after the ignition switch is placed in the OFF position. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs. WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof. When closing: If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up. If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof. WARNING ● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints. ● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing. CAUTION ● Remove water drops, snow, ice or sand from the moonroof before opening. ● Do not place heavy objects on the moonroof or surrounding area. Sunshade Open and close the sunshade by sliding it for- ward or backward. If the moonroof does not close Have your NISSAN dealer check and repair the moonroof. Instruments and controls 2-53 INTERIOR LIGHT The interior light has a three-position switch and operates regardless of ignition switch position. When the switch is in the ON position 䊊1 , the interior lights illuminate, regardless of door posi- tion. The lights will go off after about 15 minutes unless the ignition switch is placed in the ON position. When the switch is in the DOOR or normal operation position 䊊2 , the interior lights, puddle lights (if so equipped) and cargo light will stay on for about 30 seconds when: ● The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. ● The driver’s door is opened and then closed while the key is removed from the ignition switch. ● The key is removed from the ignition switch while all doors are closed. The lights will turn off while the 30 second timer is activated when: ● The driver’s door is locked by the keyfob, a key, or the power door lock switch. ● The ignition switch is turned ON. Type A Type B LIC0585 LIC0630 2-54 Instruments and controls When the switch is in the OFF position 䊊3 , the interior lights do not illuminate, regardless of door position. The puddle lights (if so equipped) and cargo light come on when any front or rear pas- senger door is opened. The lights will turn off automatically after 15 min- utes while doors are open to prevent the battery from becoming discharged. NOTE: The footwell and door step lights (if so equipped) illuminate when the driver and passenger doors are open regardless of the interior light switch position. These lights will turn off automatically after about 15 minutes while doors are open to prevent the battery from becoming discharged. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. PERSONAL LIGHTS (if so equipped) LIC0587 CONSOLE LIGHT (if so equipped) The console light 䊊1 will turn on whenever the parking lights or headlights are illuminated. The console light brightness can be adjusted with the illumination brightness control. LIC0623 The personal lights on the overhead console can be swiveled 360 degrees. To turn on the light, press the button. Press the button again to turn off the light. Instruments and controls 2-55 MAP LIGHTS (if so equipped) HOMELINK姞 UNIVERSAL TRANSCEIVER (if so equipped) The HomeLink姞 Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink姞 Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems. ● Is powered by your vehicle’s battery. No separate batteries are required. If the vehi- cle’s battery is discharged or is discon- nected, HomeLink姞 will retain all program- ming. Once the HomeLink姞 Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink姞 Universal Transceiver buttons should be erased for security purposes. For additional information, refer to “Program- ming HomeLink姞” later in this section. the vehicle, WARNING ● Do not use the HomeLink姞 Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death. ● During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming. ● Your vehicle’s engine should be turned off while programming the HomeLink姞 Universal Transceiver. LIC0586 To turn the map lights on, press the switches. To turn them off, press the switches again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. 2-56 Instruments and controls WIC0986 PROGRAMMING HOMELINK姞 1. To begin, press and hold the two outer HomeLink姞 buttons (to clear the memory) until the indicator light 䊊1 blinks (after 20 seconds). Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink姞 surface. WIC0987 3. Using both hands, simultaneously press and hold both the HomeLink姞 button you want to program and the hand-held transmitter but- ton. DO NOT release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLink姞 flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro- 5. grammed device, press and hold the pro- grammed HomeLink姞 button — releasing when the device begins to activate. If the indicator light on the HomeLink姞 blinks rapidly for 2 seconds and then turns solid, HomeLink姞 has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train the HomeLink姞 to complete the programming which may require a ladder and another per- son for convenience. 6. Press and release the “smart” or “learn” pro- gram button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button. NOTE: Once you have pressed and released the program button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step. Instruments and controls 2-57 7. Within 30 seconds of pressing and releas- ing the garage door opener’s program but- ton, quickly and firmly press and release the HomeLink姞 button you’ve just programmed. Press and release the HomeLink姞 button up to 3 times to complete the training. 8. Your HomeLink姞 button should now be pro- grammed. (To program the remaining HomeLink姞 buttons for additional door or gate openers, follow steps 2-4 only.) all previously NOTE: Do not repeat step 1 unless you want to “clear” programmed HomeLink姞 buttons. If you have any questions or are having difficulty programming your HomeLink姞 buttons, refer to the HomeLink姞 web site at: www.homelink.com or call 1-800-355-3515. PROGRAMMING HOMELINK姞 FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLink姞, continue to press and hold the HomeLink姞 button (see steps 2 - 4under “Pro- gramming HomeLink姞”) while you press and re- press (“cycle”) your hand-held transmitters every 2-58 Instruments and controls 2 seconds until the indicator light flashes rapidly (indicating successful programming). NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the “cycling” process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINK姞 UNIVERSAL TRANSCEIVER The HomeLink姞 Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLink姞 Universal Transceiver button. The amber indicator light will illuminate while the signal is being transmitted. PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLink姞 does not quickly learn the hand- held transmitter information: ● replace the hand-held transmitter batteries with new batteries. ● press and hold both the HomeLink姞 and hand-held transmitter buttons without inter- ruption. ● position the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink姞 surface. Hold the transmitter in that position for up to 15 seconds. If HomeLink姞 is not programmed within that time, try holding the transmitter in another position – keeping the indicator light in view at all times. If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). ● position the hand-held transmitter with its from the facing away battery HomeLink姞 surface. area This transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user’s authority to op- erate the equipment. DOC: ISTC 1763K1313 FCC I.D. CV2V67690 REPROGRAMMING A SINGLE HOMELINK姞 BUTTON To reprogram a HomeLink姞 Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLink姞 but- ton. Do not release the button until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3inches (26 - 76 mm) away from the HomeLink姞 surface. 3. Press and hold the hand-held transmitter button. 4. The HomeLink姞 indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons. The HomeLink姞 Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink姞 button that was just programmed. This procedure will not affect any other programmed HomeLink姞 buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink姞. Consult the Owner’s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLink姞 Univer- sal Transceiver with your new transmitter information. FCC Notice: This device complies with FCC rules part 15 and RSS-210 of Industry Canada. Opera- tion is subject to the following two condi- tions: (1) This device may not cause harmful in- terference and (2) This device must accept any interference that may be received, in- cluding interference that may cause undes- ired operation. Instruments and controls 2-59 MEMO 2-60 Instruments and controls 3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN vehicle immobilizer system keys (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4 Locking with power door lock switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Wide Open doors (if so equipped) . . . . . . . . . . . . . . . 3-5 Automatic door locks (if so equipped). . . . . . . . . . . . . 3-6 Child safety rear door lock (Crew Cab models only) . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Remote keyless entry system (if so equipped). . . . . . . . . 3-7 How to use remote keyless entry system . . . . . . . . . . 3-8 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Pedal position adjustment (if so equipped) . . . . . . . . . . 3-14 Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Vanity mirrors (if so equipped). . . . . . . . . . . . . . . . . . . 3-16 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Rearview mirror (if so equipped). . . . . . . . . . . . . . . . . 3-16 Automatic anti-glare rearview mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Automatic drive positioner (if so equipped) . . . . . . . . . . 3-24 Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-24 Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26 System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26 KEYS 1. 2. WPD0128 Two master keys (black) with transpon- der chip (if so equipped) and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip (if so equipped) Key number plate Transponder chip (if so equipped) 3. 4. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. 3-2 Pre-driving checks and adjustments your NISSAN dealer for registration. This is be- cause the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS (if so equipped) You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. The master key can be used for all the locks. The valet key cannot be used for the console box lock, the bedside storage compartment lock, or the glove box lock (if so equipped). To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can dupli- cate your existing key. As many as five NISSAN Vehicle Immobilizer System keys can be used with one vehicle. You should bring all NISSAN Vehicle Immobilizer System keys that you have to DOORS When the doors are locked using one of the following methods, the doors can not be opened using the inside or outside door handles. The doors must be unlocked to open the doors. WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders. ● Before opening any door, always look for and avoid oncoming traffic. ● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents. Driver’s side WPD0311 LOCKING WITH KEY Manual (if so equipped) To lock a door, turn the key toward the front of the vehicle 䊊1 . To unlock, turn the key toward the rear 䊊2 . LPD0240 Power (if so equipped) The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front 䊊1 of the vehicle locks all doors. Turning the key one time toward the rear 䊊2 of the vehicle unlocks that door. From that position, returning the key to neutral 䊊3 (where the key can only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks all doors 䊊4 . Pre-driving checks and adjustments 3-3 Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key toward the front of the vehicle for longer than 1 second after the door is locked. Windows stop when the key cylinder is released. 3-4 Pre-driving checks and adjustments Inside lock LPD0241 LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position 䊊1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position 䊊2 . WPD0381 LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) to the lock position 䊊1 . When locking the door this way, be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver’s or front passenger’s side) to the unlock position 䊊2 . Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the key in the ignition switch and any door open, all doors will lock and then unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle. LPD0278 WIDE OPEN DOORS (if so equipped) LPD0266 2. From the outside, pull the door handle 䊊1 toward you. CAUTION Do not open the Wide Open door to the full open position while the fuel-filler door is open; only open it as far as the first detent. Opening the door to the full open position may damage the fuel-filler door and Wide Open door. The Wide Open doors open nearly 180° to allow access to the rear of the cab. 1. Open the driver’s or passenger’s door. Pre-driving checks and adjustments 3-5 LPD0267 From the inside, pull the inside door handle to- ward you. The door will unlock automatically. 3. Open the door to the desired position. AUTOMATIC DOOR LOCKS (if so equipped) ● All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h). ● All doors unlock automatically when the transmission is placed in the P (Park) posi- tion. The automatic unlock function can be de- activated or activated. To deactivate or acti- vate the automatic door unlock system, perform the following procedure: LPD0265 1. Close all doors. 2. Place the ignition switch in the ON position. 3. Within 20 seconds of performing Step 2, push and hold the power door lock switch to position (UNLOCK) for more than the 5 seconds. 4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once. 5. The ignition switch must be placed in the OFF and ON position again between each setting change. 3-6 Pre-driving checks and adjustments When the automatic door unlock system is deac- tivated, the doors do not unlock when the trans- mission is placed in the P (Park) position. To unlock the door manually, use the inside lock knob or the power door lock switch (driver’s or front passenger’s side). REMOTE KEYLESS ENTRY SYSTEM (if so equipped) WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufac- turer for the possible influences before use. ● The remote keyless entry keyfob trans- mits radio waves when the buttons are pushed. The FAA advises radio waves may affect aircraft navigation and com- munication systems. Do not operate the remote keyless entry keyfob while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored for a flight. It is possible to lock/unlock all doors, turn on the

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2011 Nissan Titan Owners Manual