2011 Nissan Frontier Owners Manual

dent and personal injury.

● If the wheels are changed for any reason, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade vehicle handling char- acteristics, affect the VDC system and/or interference with the brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Refer to “Wheels and tires” in the “Technical and consumer in- formation” section of this manual for wheel off-set dimensions.

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indi- cated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

● Do not install a damaged or deformed wheel or tire even if it has been re- paired. Such wheels or tires could have structural damage and could fail with- out warning.

retread tires

is not

● The use of

recommended. ● For additional

information regarding tires, refer to “Important Tire Safety In- formation” (US) or “Tire Safety Informa- tion” (Canada) in the Warranty Informa- tion Booklet.

Four-wheel drive models

CAUTION

Always use tires of the same type, size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires on the front and rear axles which will cause excessive tire wear and may dam- age the transmission, transfer case and differential gears.

If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer.

Maintenance and do-it-yourself 8-41

Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.

● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Infor- mation” (Canada) in the Warranty In- formation Booklet.

Care of wheels ● Wash the wheels when washing the vehicle

to maintain their appearance.

● Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

● Do not use abrasive cleaners when washing

the wheels.

● Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

8-42 Maintenance and do-it-yourself

● NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

Spare tire (FULL SIZE TEMPORARY USE ONLY spare tire) Your vehicle may be equipped with a full size spare that is a different size or brand than the tires originally installed on the vehicle. This full size spare tire is intended for temporary use only and should be replaced at the first opportunity.

Observe the following precautions if the full size temporary use only spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident:

WARNING

● The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid possible tire or differen- tial damage.

● Drive carefully while the spare tire is installed. Avoid sharp turns and abrupt braking while driving. The vehicle driv- ing performance may be affected when driving on wet or snow covered roads.

● When the temporary full size spare is installed, the following systems may not work correctly: – Tire Pressure Monitoring System

(TPMS).

– Vehicle Dynamic Control (VDC) System. ● Periodically check spare tire inflation pressure. Always keep the spare tire inflated to the pressure specification shown on the tire and loading informa- tion label.

● With the spare tire installed do not drive the vehicle at speeds faster than 50
MPH (80 km/h).

● When driving on roads covered with snow or ice, the temporary spare tire should be used on the front wheels and the original tire used on the rear wheels. Use tire chains only on the drive wheels. ● Do not use the spare tire on other vehicles. ● Do not use more than one spare tire at

the same time.

CAUTION

● Do not use tire chains on a spare tire. Tire chains will not fit properly and may cause damage to the vehicle.

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Engine oil and oil filter recommendations . . . . . . . . . . 9-6
Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-9

When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Vehicle identification number (VIN) plate . . . . . . . . . 9-10
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . 9-11
Emission control information label . . . . . . . . . . . . . . . 9-12
Tire and loading information label. . . . . . . . . . . . . . . . 9-12
Air conditioner specification label. . . . . . . . . . . . . . . . 9-12
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Installing front license plate with grommets . . . . . . . 9-13
Installing front license plate without grommets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-13

Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Securing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Utili-track™ channel system (if so equipped) . . . . . . 9-17
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Truck-camper loading information . . . . . . . . . . . . . . . . . . 9-23
Crew Cab Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
King Cab models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Special Body vehicles. . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Location for center of gravity . . . . . . . . . . . . . . . . . . . . 9-23
Vehicle load weight capacity . . . . . . . . . . . . . . . . . . . . 9-24
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . 9-24
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Towing load/specification. . . . . . . . . . . . . . . . . . . . . . . 9-28
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-29
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-35
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-36
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-36
Reporting safety defects . . . . . . . . . . . . . . . . . . . . . . . . . . 9-37
Readiness for inspection/maintenance (I/M) test . . . . . 9-38
Event Data Recorders (EDR). . . . . . . . . . . . . . . . . . . . . . . 9-38
Owner’s Manual/Service Manual order information . . . 9-39
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-39

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.

Fuel Engine oil *7

Drain and Refill

With oil filter change Without oil filter change With oil filter change Without oil filter change

Cooling system

With reservoir

Manual transmission gear oil

Automatic transmission fluid Power steering fluid (PSF) Brake and clutch fluid

QR25DE

VQ40DE

QR25DE VQ40DE 5M/T 6 M/T 4X2
6 M/T 4X4

Capacity (Approximate) US measure 21 1/8gal

Imp measure 17-5/8 gal

4-7/8 qt 4-1/2 qt

5-3/8 qt 5-1/8 qt

4 qt 3-3/4 qt

4-1/2 qt 4-1/4 qt

Liter 80

4.6
4.3

5.1
4.8

Recommended Fluids and Lubricants

See “Fuel recommendation” later in this section.

(cid:129) Engine oil with API Certification Mark *1
(cid:129) Viscosity SAE 5W-30

2-1/8 gal 2-1/4 gal 2-1/2 qt 3-1/2 qt 3-3/4 qt

2-1/2 gal 2-3/4 gal 3-1/8 qt 4-1/4 qt 4-1/2 qt Refill to the proper level according to the instruc- tions in the “Maintenance and do-it-yourself” section.

9.4
10.2
2.9
4.0
4.2

Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent

Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85

Genuine NISSAN Matic S ATF *2
Genuine NISSAN PSF or equivalent.*3
Genuine NISSAN Super Heavy Duty Brake Fluid *4 or equivalent DOT 3
NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a) *5

Multi-purpose grease Air conditioning system refrigerant

— —

— —

— —

9-2 Technical and consumer information

Air conditioning system oil Transfer fluid Front final drive oil

Capacity (Approximate) US measure — 2-1/8 qt 1-3/4 pt

Imp measure — 4-1/2 qt 1-1/2 pt

Rear final drive oil (except 6 speed M/T and O/R vehicles)

3-3/8 pt

Rear final drive oil 6 speed M/T and O/R vehicles only

4-1/4 pt

2-7/8 pt

3-1/2 pt

Windshield-washer fluid

1-1/4 gal

1 gal

Liter — 2.0
0.85

1.6

2.0

4.5

Recommended Fluids and Lubricants

Genuine NISSAN A/C System Oil Type R or equivalent *5
Genuine NISSAN Matic D ATF recommended *6
Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5 SAE 80W-90 *8
Genuine NISSAN differential oil synthetic 75W-90 or API GL-5 syn- thetic gear oil, Viscosity SAE 75W-90 *9
Genuine NISSAN differential oil synthetic 75W-140 or API GL-5
synthetic gear oil, Viscosity SAE 75W-140 *9
Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti- freeze or equivalent

*1: For further details, see “Engine oil and oil filter recommendations” in this section. *2: If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission fluid other than Genuine NISSAN Matic S ATF or

Genuine NISSAN Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty.

*3: DEXRON™ VI type ATF may also be used. *4: Available in mainland USA through a NISSAN dealer. *5: For further details, see “Air conditioner specification label” in this section. *6: Using fluid other than Genuine NISSAN Matic D ATF will cause deterioration in driveability and transfer durability, and may damage the transfer, which is not covered by the NISSAN

new vehicle limited warranty.

*7: For further details, see “Changing engine oil” in the “Maintenance and do-it-yourself” section. *8: For hot climates, Viscosity SAE 90 is suitable for ambient temperatures above 0° (32°F) *9: See a NISSAN dealer for service for synthetic oil.

Technical and consumer information 9-3

FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).

CAUTION

● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

● Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.

● Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN new vehicle lim- ited warranty.

Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter (WWFC) specifi- cations where it is available. Many of the automo- bile manufacturers developed this specification to improve emission control system and vehicle performance. Ask your service station manager if the gasoline meets the WWFC specifications. 9-4 Technical and consumer information

Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.

If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. ● The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline.

● If an oxygenate-blend other

than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.

fuels,

oxygenate-blend

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage.

E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S. government regulations require fuel ethanol dispensing pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy “spark knock.” (“Spark knock” is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level

● U.S. government

regulations require ethanol dispensing pumps to be identi- fied by a small, square, orange and black label with the common abbrevia- tion or the appropriate percentage for that region.

roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible.

ignition timing may result

Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

CAUTION

● Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.

● E-85 is a mixture of approximately 85% 15% unleaded

ethanol

and

fuel gasoline.

Technical and consumer information 9-5

Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in “Change intervals.” Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle limited war- ranty.

ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.

Select only engine oils that meet the American Petroleum Institute (API) certification or Interna- tional Lubricant Standardization and Approval 9-6 Technical and consumer information

WTI0183
Committee (ILSAC) certification and SAE vis- cosity standard. These oils have the API certifica- tion mark on the front of the container. Oils which do not have the specified quality label should not be used as they could cause engine damage. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used.

CAUTION

The use of any other refrigerant or oil will cause severe damage to the air condition- ing system and will require the replace- ment of all air conditioner system components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.

Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle.

Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance driving at cold out-

side temperatures

● driving in dusty conditions ● extensive idling ● towing a trailer ● stop and go commuting Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule. AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the oil, NISSAN A/C system oil Type R or the exact equiva- lents.

Technical and consumer information 9-7

SPECIFICATIONS

ENGINE

Model

Type Cylinder arrangement Bore x Stroke Displacement Firing order

Idle speed M/T A/T (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle

Spark plug

Spark plug gap (Nominal)

Camshaft operation This spark ignition system complies with the Canadian standard ICES-002.

Timing chain

9-8 Technical and consumer information

QR25DE

Gasoline, 4-cycle, DOHC 4-cylinder in-line

in (mm) 3.5 x 3.9 (89.0 x 100.0)

cu in (cm3) 151.82 (2,488)

1–3–4–2

VQ40DE

Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60° 3.760 x 3.622 (95.5 x 92) 241.30 (3,954) 1–2–3–4–5–6

See the “Emission control information label” on the underside of the hood.

Standard PLZKAR6A-11

in (mm) 0.043 (1.1)

DILFR5A11

0.043 (1.1)

Timing chain

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Wheels

Tires

Spare tire

15 x 7.0J 16 x 7.0J 18 x 7.5J

P235/75R15
P265/70R16
P265/75R16
P265/60R18
Full size

Overall length

Short wheel base Long wheel base

Overall width Overall height

With roof rack Without roof rack

S and SV I-4 King cab models

(4x2)

SV and Pro-4X King cab models

(4x2 and 4x4) Crew cab models

Front Track Rear Track Wheelbase

Short wheel base Long wheel base

Gross vehicle weight rating Gross axle weight rating

Front Rear

in (mm) in (mm) in (mm)

in (mm)

in (mm)

in (mm)

in (mm) in (mm) in (mm)

205.5 (5,220) 219.4 (5,574) 72.8 (1,850)

73.9 (1,878)

68.7 (1,745)

69.7 (1,770)

70.1 (1,780) 61.8 (1,570) 61.8 (1,570)

in (mm) in (mm) lb (kg) See the “F.M.V.S.S./C.M.V.

125.9 (3,199) 139.9 (3,554)

S.S. certification label” on the center pillar between the driver’s side front and rear doors.

lb (kg) lb (kg)

Technical and consumer information 9-9

VEHICLE IDENTIFICATION

LTI0085
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

LTI0086
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

9-10 Technical and consumer information

LTI0130

LTI0127

QR25DE engine ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

VQ40DE engine

LTI0136

F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.

Technical and consumer information 9-11

LTI0133

EMISSION CONTROL INFORMATION LABEL The emission control tached to the underside of the hood as shown.

information label

is at-

LTI0135
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown.

LTI0206
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed to the underside of the hood as shown.

9-12 Technical and consumer information

INSTALLING FRONT LICENSE PLATE

VEHICLE LOADING INFORMATION

License plate bolt tightening torque:

3.8 - 4.7 ft-lb (5.10 - 6.37 N·m)

INSTALLING FRONT LICENSE PLATE WITHOUT GROMMETS Use the following steps to mount the front license plate without grommets: 1. Make a shallow hole in each plastic finisher at the location mark (small dimple) using a 0.31 in (8 mm) drill. To avoid damaging the threads behind the finisher, apply only light pressure to the drill.

LTI0137

2. Mount the license plate bracket using two 8

mm slotted hex head screws.

INSTALLING FRONT LICENSE PLATE WITH GROMMETS Use the following steps to mount the front license plate with grommets:

1. Make holes on the plastic finisher at the location mark (small dimple) using a 0.37 in (9.5 mm) drill. Apply light pressure to the drill. Insert two plastic grommets provided. Install the license plate holder using the two bolts (and washers) provided.

2. Mount the license plate using two M6-14

mm bolts.

WARNING

● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed.

● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

● Be sure everyone in your vehicle is in a seat and using a seat belt properly.

TERMS It is important to familiarize yourself with the following terms before loading your vehicle: ● Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and optional equipment, flu- ids, emergency tools, and spare tire assembly. This weight does not in- clude passengers and cargo.

Technical and consumer information 9-13

● GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

● GVWR (Gross Vehicle Weight Rat- ing) - maximum total combined weight of the unloaded vehicle, pas- sengers, trailer tongue load and any other optional equipment. This information is lo- cated on the F.M.V.S.S./C.M.V.S.S. certification label.

luggage,

hitch,

● GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle. This informa- tion the located F.M.V.S.S./C.M.V.S.S. certification label.

on

is

● GCWR (Gross Combined Weight rating) - The maximum total weight rating of the vehicle, passengers, cargo, and trailer.

9-14 Technical and consumer information

(if

label

Information

Do not exceed the load limit of your ve- hicle shown as “The combined weight of occupants and cargo” on the Tire and Loading so equipped). Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Information label (if so equipped). To get “the combined weight of occu- pants and cargo”, add the weight of all occupants, then add the total luggage weight. Examples are shown in the follow- ing illustration.

limit specified of

● Vehicle Capacity Weight, Load limit, Total load capacity - maximum total weight the load (passengers and cargo) for the ve- hicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be in- cluded as part of the cargo load. This information is located on the Tire and Loading Information label (if so equipped).

● Cargo capacity - permissible weight of cargo, the subtracted weight of occupants from the load limit.

VEHICLE LOAD CAPACITY Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. Both the GVWR and GAWR are located on the F.M.V.S.S./C.M.V.S.S. certification label. See “Measurement of weights” later in this section.

Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard.

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.

4. The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400-750 (5 X 150) = 650 lbs) or (640-340 (5 X 70) = 300 kg.)

Example

LTI0152

Technical and consumer information 9-15

WARNING

● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.

● Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

LTI0102

SECURING THE LOAD For your convenience, tie down hooks (if so equipped) are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box.

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the available cargo and lug- gage load capacity of your vehicle.

6.

Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See “Measurement of weights” later in this section. Also check tires for proper inflation pres- sures. See the Tire and Loading Informa- tion label.

9-16 Technical and consumer information

LTI0107

Side channels

1. 2. Header channel 3. Channel sections 4. UTILI-TRACK™ CHANNEL SYSTEM (if so equipped)

Floor channels

Check the tightness of the tie-down cleat peri- odically during a trip to make sure the center bolt has not become loose. Install the tie-down cleat as follows: 1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors.

2. Loosen the center bolt completely.

WARNING

● Properly install and tighten the tie- down cleats into the Utili-track™ chan- nel system. Also, do not attach any rope or straps directly to the channel. Failure to properly install the tie-down cleats or attaching ropes or straps directly to the channel can cause the cargo to become unsecured. In a sudden stop or colli- sion, unsecured cargo could cause per- sonal injury.

● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

The Utili-track™ channel system allows you to move tie-down clamps in the bed to the best location to secure a load.

The tie-down cleats must be installed so the clamp is properly seated in the notches in the rail. If the tie-down cleat is not seated in the notches, it will not be flush with the rail and cannot be properly tightened. The bolt in the center of the cleat must be tightened hand tight (20 – 40 inch pounds)

Technical and consumer information 9-17

3.

LTI0103
Insert the cleat into the channel perpendicu- lar to the channel as shown. Then rotate the cleat clockwise 90° and slide it to the de- sired location.

9-18 Technical and consumer information

LTI0104
4. Position the cleat so the nubs on the bottom

fully seat into the channel detents.

5. There should be no gap between the bottom of the cleat and the top of the channel. Tighten the center bolt hand tight (20-40
inch pounds).

WTI0124

Technical and consumer information 9-19

LTI0106

CAUTION

● Install only one cleat per section of

channel.

● Applying loads at angles to the cleats greater then 45° or loads greater than 150 lbs. (header and floor channels) or 200 lbs. (side channels) may cause damage to the channel or bed.

9-20 Technical and consumer information

1 correct installation, 2 incorrect installation

WARNING

Do not install accessories over the gap between the front and rear side channels. Doing this could affect the rear structure in certain rear impacts, which could result in serious injury.

LTI0123

WTI0119

CAUTION

Properly secure all cargo with ropes or straps to prevent it from sliding or shifting. Use the channel end stoppers to help se- cure items in the channels from sliding off the end of the truck bed.

Channel end stoppers (if so equipped) The channel end stoppers should be used to help prevent accessories installed in the channels from sliding or shifting off the end of the truck bed. They must be installed so they are properly seated in the detents in the channel.

Technical and consumer information 9-21

● Overloading not only can shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and longer brak- ing distances. This may cause a premature tire failure which could result in a serious accident and personal injury. Failures caused by overloading are not covered vehicle’s warranty.

the

by

WARNING

● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or colli- sion, unsecured cargo could cause personal injury.

● Do not

load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could oc- cur, or it can change the way your vehicle handles. This could result in loss of control and cause per- sonal injury.

Install the channels end stoppers as follows:

1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors.

2. Loosen the bolt on the center of the end stopper with the provided wrench and insert it into the channel.

3. Position the end stopper to the desired lo- cation on the channel so the nubs on the bottom of the end stopper fully seat into the channel detents.

4. Tighten the bolt on the center of the end

stopper with the provided wrench.

LOADING TIPS ● The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification label.

● Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.

9-22 Technical and consumer information

TRUCK-CAMPER LOADING INFORMATION

CREW CAB MODELS Crew Cab short wheel base models should not be used to carry a slide-in camper. KING CAB MODELS This information is provided for you to properly install a slide-in camper and is based on the National Highway Traffic Safety Administration regulations. It is recommended that, before in- stalling the camper, you carefully read the follow- ing information and ensure that the camper meets the specifications. This information may not apply to some Canada model vehicles. SPECIAL BODY VEHICLES Some vehicles are equipped with commercial or camper bodies. However, this Owner’s Manual does not cover these options. For further infor- mation, please refer to the body manufacturer’s instruction manual.

LTI0128

LOCATION FOR CENTER OF GRAVITY The illustration indicates the recommended cargo center of gravity location. King Cab: L1 = 41.5 in (1,054 mm)

WARNING

Improper loading may be dangerous. If a load is too far back, it can affect handling characteristics. If a load is too far forward, the front axle may be overloaded.

LTI0129
When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the camper manufacturer’s weight figure, plus: ● the weight of installed additional camper included in the camper

equipment not manufacturer’s weight figure, ● the weight of camper cargo, ● and the weight of occupants in the camper. The total cargo load should not exceed the truck’s pay load weight rating and the camper’s center of gravity should fall within the truck’s recommended center of gravity location when installed.

Technical and consumer information 9-23

loads. Individual axle loads should not ex- ceed either of the gross axle weight rat- ings (GAWR). The total of the axle loads should not exceed the gross vehicle weight rating (GVWR). These ratings are given on the vehicle certification label. If weight ratings are exceeded, move or re- move items to bring all weights below the ratings.

WARNING

Overloading or improper loading can ad- versely affect vehicle handling, braking and performance and may lead to accidents. VEHICLE LOAD WEIGHT CAPACITY The vehicle payload weight capacity shown on the Tire and Loading Information label, see “Tire and Loading Information label” in this section, indicates the maximum total weight of passen- gers, optional equipment (air conditioning, trailer hitch, etc) and cargo that your vehicle is designed to carry. Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See ’’Vehicle Loading Information’’ earlier in this section for details. Also check tires for proper inflation pressures. See the Tire and Loading Information label. MEASUREMENT OF WEIGHTS Secure loose items to prevent weight shifts that could affect the balance of your vehicle. When the vehicle is loaded, drive to a scale and weigh the front and the rear wheels separately to determine axle 9-24 Technical and consumer information

TOWING A TRAILER

WARNING

Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents.

CAUTION

● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km). Your engine, axle or other parts could be damaged.

● For the first 500 miles (800 km) that you tow a trailer, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of your vehicle wear in at the heavier loads.

Your new vehicle was designed to be used pri- marily to carry passengers and cargo. Remember that towing a trailer places additional loads on your vehicle’s engine, drive train, steering, brak- ing and other systems. A NISSAN Towing Guide (U.S. only) is available on the website at www.nissanusa.com. This guide includes information on trailer towing ca- pability and the special equipment required for proper towing.

specified

MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value “Towing Load/Specification” chart found later in this sec- tion. The total trailer load equals trailer weight plus its cargo weight. ● When towing a trailer load of 3,500 lbs. (1587 kg) or more, trailers with a brake system MUST be used.

the

in

The maximum Gross Combined Weight Rating (GCWR) should not exceed the value specified in the following “Towing Load/Specification” chart.

LTI0161
The GCWR equals the combined weight of the towing vehicle (including passengers and cargo) plus the total trailer load. Towing loads greater than these or using improper towing equipment could adversely affect vehicle handling, braking and performance. The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads, but also the places you plan to tow. Tow weights appro- priate for level highway driving may have to be reduced for low traction situations (for example, on slippery boat ramps).

Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.

WARNING

Overheating can result in reduced engine power and vehicle speed. The reduced speed may be lower than other traffic, which could increase the chance of a col- lision. Be especially careful when driving. If the vehicle cannot maintain a safe driv- ing speed, pull to the side of the road in a safe area. Allow the engine to cool and return to normal operation. See “If your vehicle overheats” in the “In case of emer- gency” section of this manual.

CAUTION

Vehicle damage resulting from improper towing procedures is not covered by NISSAN warranties.

Technical and consumer information 9-25

Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity. All vehicle and trailer weights can be measured using platform type scales commonly found at truck stops, highway weigh stations, building supply centers or salvage yards. To determine the available payload capacity for tongue load, use the following procedure. 1. Locate

GVWR

the

the

on

F.M.V.S.S./C.M.V.S.S. certification label.

2. Weigh your vehicle on the scale with all of the passengers and cargo that are normally in the vehicle when towing a trailer.

3. Subtract the actual vehicle weight from the GVWR. The remaining amount is the avail- able maximum tongue load.

WTI0160

CA0036

Tongue load When using a weight carrying or a weight distrib- uting hitch, keep the tongue load between 10 - 15 percent of the total trailer load or use the trailer tongue load specified by the trailer manu- facturer. The tongue load must be within the maximum tongue load limits shown in the follow- ing “Towing Load/Specification” chart. the tongue load becomes excessive, rearrange cargo to allow for proper tongue load.

If

Maximum Gross Vehicle Weight (GVW)/maximum Gross Axle Weight (GAW) The GVW of the towing vehicle must not exceed the Gross Vehicle Weight Rating (GVWR) shown on the F.M.V.S.S./C.M.V.S.S. certification label. The GVW equals the combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. In addition, front or rear GAW must not exceed the Gross Axle Weight Rating (GAWR) shown on the F.M.V.S.S./C.M.V.S.S. certification label.

9-26 Technical and consumer information

To determine the available towing capacity, use the following procedure. 1. Find the GCWR for your vehicle on the found

⬙Towing Load/Specification⬙ chart later in this section.

2. Subtract the actual vehicle weight from the GCWR. The remaining amount is the avail- able maximum towing capacity.

To determine the Gross Trailer Weight, weigh your trailer on a scale with all equipment and cargo, that are normally in the trailer when it is towed. Make sure the Gross Trailer Weight is not more than the Gross Trailer Weight Rating shown on the trailer and is not more than the calculated available maximum towing capacity. Also weigh the front and rear axles on the scale to make sure the Front Gross Axle Weight and Rear Gross Axle Weight are not more than Front Gross Axle Weight and Rear Gross Axle Weight on the F.M.V.S.S./C.M.V.S.S. label. The cargo in the trailer and vehicle may need to be moved or removed to meet the specified ratings. Example: ● Gross Vehicle Weight (GVW) as weighed on a scale- including passengers, cargo and hitch - 5,185 lb. (2352 kg).

certification

● Gross Vehicle Weight Rating (GVWR) from F.M.V.S.S./C.M.V.S.S. certification label - 5,815 lb. (2638 kg).

● Gross Combined Weight Rating (GCWR) from “Towing Load/Specification⬙ chart - 11,133 lb. (5050 kg).

● Maximum Trailer towing capacity from “Tow- ing Load/Specification⬙ chart - 6,100 lb. (2767 kg).

5,815 lb. (2638 kg) – 5,185 lb. (2352 kg)

GVWR GVW

= 630 lb. (286 kg)

Available for tongue

11,133 lb. (5050 kg) – 5,185 lb. (2352 kg)

weight

GCWR GVW

= 5,948 lb. (2698 kg) Capacity available for

towing

630 lb. (286 kg) Available tongue weight

/ 5,948 lb. (2698 kg)

Available capacity

10 % tongue weight

The available towing capacity may be less than the maximum towing capacity due to the passen- ger and cargo load in the vehicle. Remember to keep trailer tongue weight be- tween 10 - 15% of the trailer weight or within the trailer tongue load specification recommended

by the trailer manufacturer. If the tongue load becomes excessive, rearrange the cargo to ob- tain the proper tongue load. Do not exceed the maximum tongue weight specification shown in the “Towing load/specification” chart even if the calculated available tongue weight is greater than 15%. If the calculated tongue weight is less than 10% , reduce the total trailer weight to match the available tongue weight. Always verify that available capacities are within the required ratings. Trailer frontal area

CAUTION

Exceeding the maximum trailer frontal area specification may exceed the towing capac- ity of the vehicle. This may affect the towing performance and lead to vehicle damage.

The trailer frontal area affects the towing load of a trailer. The frontal area is the total area of the vehicle and trailer that is affected by air resis- tance while towing. Do not exceed the maximum trailer frontal area specification shown in the ⬙Towing Load/Specification” chart. The frontal area can be determined by multiplying the width of the trailer by the height of the trailer. For example, a trailer that is 8 feet wide by 6 feet tall has a trailer frontal area of 48 square feet.

Technical and consumer information 9-27

TOWING LOAD/SPECIFICATION

Maximum Towing Capacity*1, *2, *3
Maximum Tongue Load*2, *3
Maximum Gross Combined Weight Rating Maximum trailer frontal area

King Cab 2WD (4 cyl) 3,500 lb. (1,588 kg) 350 lb. (158 kg)

King Cab 2WD (6 cyl) 6,505 lb. (2,949 kg) 650 lb. (295 kg)

King Cab 4WD (6 cyl) 6,300 lb. (2,858 kg) 630 lb. (285 kg)

Crew Cab 2WD 6,300 lb. (2,858 kg) 630 lb. (285 kg)

Crew Cab 4WD 6,100 lb. (2,767 kg) 610 lb. (276 kg)

7,940 lb. (3,600 kg)

11,135 lb. (5,050 kg)

11,135 lb. (5,050 kg)

11,135 lb. (5,050 kg)

11,135 lb. (5,050 kg)

60 sq feet (5.52 sq meters)

*1: ● The towing capacity values are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers,

cargo and/or optional equipment will add weight to the vehicle and reduce your vehicle’s maximum towing capacity.

● All towing above 1,000 lb (454 kg) requires the use of trailer brakes. NISSAN recommends the use of a tandem axle trailer whenever towing above

3,000 lb (1,361 kg).

*2: The maximum towing capacity when using the genuine NISSAN step bumper as a ball mount is 3,500 lb. (1,588 kg) and 350 lb. (158 kg) tongue load. *3: Use of a weight-distributing hitch system is recommended when towing over 5,000 lbs.

9-28 Technical and consumer information

● The threaded shank of the hitch ball must be long enough to be properly secured to the ball mount. There should be at least 2
threads showing beyond the lock washer and nut. Ball mount The hitch ball is attached to the ball mount and the ball mount is inserted into the hitch receiver. Choose a proper class ball mount based on the trailer weight. Additionally, the ball mount should be chosen to keep the trailer tongue level with the ground.

TOWING SAFETY Trailer hitch Your vehicle may be equipped with an optional trailer tow package. The trailer tow package in- cludes a receiver-type frame mounted hitch. This hitch is rated for the maximum towing capacity of this vehicle when the proper towing equipment is used. Choose a proper ball mount and hitch ball that is rated for the trailer to be towed. Genuine NISSAN ball mounts and hitch balls are available from your NISSAN dealer.

If your vehicle is not equipped with the optional trailer tow package, check the towing capacity of your bumper hitch or receiver-type frame mounted hitch. Choose a proper hitch for your vehicle and trailer. A genuine NISSAN trailer hitch is available from your NISSAN dealer. Make sure the trailer hitch is securely attached to the vehicle to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks.

WARNING

Trailer hitch components have specific weight ratings. Your vehicle may be ca- pable of towing a trailer heavier than the weight rating of the hitch components. Never exceed the weight rating of the hitch components. Doing so can cause serious personal injury or property damage.

Hitch ball Choose a hitch ball of the proper size and weight rating for your trailer: ● The required hitch ball size is stamped on most trailer couplers. Most hitch balls also have the size printed on the top of the ball. ● Choose the proper class hitch ball based on

the trailer weight.

● The diameter of the threaded shank of the hitch ball must be matched to the ball mount hole diameter. The hitch ball shank should be no more than 1/16” smaller than the hole in the ball mount.

Technical and consumer information 9-29

Weight distribution hitch This type of hitch is also called a “load-leveling” or “equalizing” hitch. A set of bars attach to the ball mount and to the trailer to distribute the tongue weight (hitch weight) of your trailer. Many ve- hicles can’t carry the full tongue weight of a given trailer, and need some of the tongue weight transferred through the frame and pushing down on the front wheels. This gives stability to the tow vehicle.

A weight-distributing hitch system (Class IV) is recommended if you plan to tow trailers with a maximum weight over 5,000 lbs. Check with the trailer and towing equipment manufacturers to determine if they recommend the use of a weight- distributing hitch system.

NOTE:

A weight-distributing hitch system may af- fect the operation of trailer surge brakes. If you are considering use of a weight- distributing hitch system with a surge brake-equipped trailer, check with the surge brake, hitch or trailer manufacturer to determine if and how this can be done. Follow the instructions provided by the manufac- turer installing and using the weight- distributing hitch system.

for

General set-up instructions are as follows:

1. Park unloaded vehicle on a level surface. With the ignition on and the doors closed, allow the vehicle to stand for several minutes so that it can level.

2. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle.

3. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0 - .5inches (0 – 13 mm) of the reference height measured in step 2. The rear bumper should be no higher than the reference height measured in step 2.

WARNING

Properly adjust the weight distributing hitch so the rear of the bumper is no higher than the measured reference height when the trailer is attached. If the rear bumper is higher than the measured reference height when loaded, the vehicle may handle unpredictably which could cause a loss of vehicle control and cause serious personal injury or property damage.

LTI0132

Bumper towing The genuine NISSAN step bumper has provi- sions to install a trailer hitch ball and is designed to tow trailers of a maximum weight of 3,500 lb (1,588 kg).

To install a trailer hitch ball cut out the circle in the center of the step bumper 䊊A , then remove it to install the trailer hitch ball. Weight carrying hitches A weight carrying or “dead weight” ball mount is one that is designed to carry the whole amount of tongue weight and gross weight directly on the ball mount and on the receiver. 9-30 Technical and consumer information

Sway control device Sudden maneuvers, wind gusts, and buffeting caused by other vehicles can affect trailer han- dling. Sway control devices may be used to help control these affects. If you choose to use one, contact a reputable trailer hitch supplier to make sure the sway control device will work with the vehicle, hitch, trailer and the trailer’s brake sys- tem. Follow the instructions provided by the manufacturer for installing and using the sway control device. Class I hitch Class I trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 2,000 lb (909 kg). Class II hitch Class II trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 3,500 lb (1,510 kg).

The genuine NISSAN step bumper is considered a Class II ball mount. Class III hitch Class III trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 5,000 lb (2,272 kg).

Class IV hitch Class IV trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 10,000 lb (4,545 kg). A weight distributing hitch should be used to tow trailers that weigh over 5,000 lb (2,272 kg).

Your vehicle may be equipped with Class IV trailer hitch equipment that has a 10,000 lb (4,545 kg) maximum weight rating, but your ve- hicle is only capable of towing the maximum trailer weights “Towing Load/Specification” chart earlier in this section.

shown

the

in

CAUTION

● Special hitches which include frame re- inforcements are required for towing above 2,000 lb (907 kg). Suitable genu- ine NISSAN hitches, ball mounts and hitch balls for pickup trucks and sport utility vehicles are available at a NISSAN dealer.

● The hitch should not be attached to or the impact-

the operation of

affect absorbing bumper.

● Do not use axle-mounted hitches.

● Do not modify the vehicle exhaust sys- tem, brake system, etc. to install a trailer hitch.

● To reduce the possibility of additional damage if your vehicle is struck from the rear, where practical, remove the receiver when not in use.

● Regularly check that all trailer hitch mounting bolts are securely mounted.

Tire pressures ● When towing a trailer, inflate the ve- hicle tires to the recommended cold tire pressure indicated on the Tire and Loading Information label.

● Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer’s specifications.

Safety chains Always use suitable safety chains between your vehicle and the trailer. The safety chains should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. The safety chains can be attached to the bumper if the hitch

Technical and consumer information 9-31

ball is mounted to the bumper. Be sure to leave enough slack in the chains to permit turning corners. Trailer lights

CAUTION

When splicing into the vehicle electrical system, a commercially available power- type module/converter must be used to provide power for all trailer lighting. This unit uses the vehicle battery as a direct power source for all trailer lights while using the vehicle tail light, stoplight and turn signal circuits as a signal source. The module/converter must draw no more that 15 milliamps from the stop and tail lamp circuits. Using a module/converter that exceeds these power requirements may damage the vehicle’s electrical sys- tem. See a reputable trailer dealer to ob- tain the proper equipment and to have it installed.

Trailer lights should comply with federal and/or local regulations. For assistance in hooking up trailer lights, contact a NISSAN dealer or repu- table trailer dealer. Vehicles equipped with the optional trailer tow package are equipped with a 7-pin trailer harness connector. A flat 4–pin har- ness is available from your dealer for vehicles 9-32 Technical and consumer information

without a tow package. If your trailer is equipped with a flat 4-pin connector, an adapter will be needed to connect the trailer lights to the vehicle. Adapters are available at auto parts stores and hitch retailers. Trailer brakes If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed. Vehicles equipped with a 7–pin trailer harness connector are pre-wired for a trailer brake con- troller. See a NISSAN dealer for a trailer brake adapter harness.

WARNING

Never connect a trailer brake system di- rectly to the vehicle brake system.

When towing a trailer load of 3,500 lbs. (1587 kg) or more, trailers with a brake system MUST be used. However, most states require a separate braking system on trailers with a loaded weight above a specific amount. Make sure the trailer meets the local regulations and the regulations where you plan to tow. Several types of braking systems are available. Surge Brakes - The surge brake actuator is mounted on the trailer tongue with a hydraulic line

running to each trailer wheel. Surge brakes are activated by the trailer pushing against the hitch ball when the tow vehicle is braking. Hydraulic surge brakes are common on rental trailers and some boat trailers. In this type of system, there is no hydraulic or electric connection for brake op- eration between the tow vehicle and the trailer. Electric Trailer Brakes - Electric braking sys- tems are activated by an electronic signal sent from a trailer brake controller (special brake- sensing module). If electric trailer brakes are used, see ⬙Electric trailer brake controller⬙ in this section.

Have a professional supplier of towing equip- ment make sure the trailer brakes are properly installed and demonstrate proper brake function testing. Electric trailer brake controller Trailers equipped with electric brakes may re- quire the installation of an aftermarket trailer brake controller. A Genuine NISSAN jumper harness is available that is specifically designed to be used when installing an aftermarket brake controller. Install the aftermarket electric trailer brake con- troller according to the manufacturer’s instruc- tions.

Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition.

● Always secure items in the trailer to prevent

load shift while driving.

● Keep the cargo load as low as possible in the trailer to keep the trailer center of gravity low. ● Load the trailer so approximately 60% of the trailer load is in the front half and 40% is in the back half. Also make sure the load is balanced side to side.

● Check your hitch, trailer tire pressure, ve- hicle tire pressure, trailer light operation, and trailer wheel lug nuts every time you attach a trailer to the vehicle.

● Be certain your rearview mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle.

● Determine the overall height of the vehicle and trailer so the required clearance is known.

Trailer towing tips In order to gain skill and an understanding of the vehicle’s behavior, you should practice turning, stopping and backing up in an area which is free from traffic. Steering stability and braking perfor- mance will be somewhat different than under normal driving conditions. ● Always secure items in the trailer to prevent

load shift while driving.

● Lock the trailer hitch coupler with a pin or lock to prevent the coupler from inadvert- ently becoming unlatched.

● Avoid abrupt starts, acceleration or stops. ● Avoid sharp turns or lane changes. ● Always drive your vehicle at a moderate

speed.

● When backing up, hold the bottom of the steering wheel with one hand. Move your hand in the direction in which you want the trailer to go. Make small corrections and back up slowly. If possible, have someone guide you when you are backing up.

Always block the wheels on both vehicle and trailer when parking. Parking on a slope is not recommended; however, if you must do so:

CAUTION

If you move the shift selector to the P (Park) position before blocking the wheels and applying the parking brake, transmission damage could occur.

1. Apply and hold the brake pedal.

2. Have someone place blocks on the downhill

side of the vehicle and trailer wheels.

3. After the wheel blocks are in place, slowly release the brake pedal until the blocks ab- sorb the vehicle load.

4. Apply the parking brake.

5. Shift the transmission into P (Park).

6. Make sure the

indicator light (if so equipped) indicates the transfer case is in 4H, 4L, or 2H and that the ATP light is off. If indicator light is flashing, or the the ATP light is ON, make sure the transmission is in P (Park) (A/T) and turn the 4WD switch to 2WD or 4H. See “Automatic transmission park warning light” in the “Instruments and controls” section and “Using four wheel drive (4WD)” in the “Starting and driving” section.

7. Turn off the engine.

Technical and consumer information 9-33

To drive away:

1. Start the vehicle.

2. Apply and hold the brake pedal.

3. Shift the transmission into gear. 4. Release the parking brake. 5. Drive slowly until the vehicle and trailer are

clear from the blocks.

the weight of

6. Apply and hold the brake pedal. 7. Have someone retrieve and store the blocks. ● While going downhill, the trailer pushing on the tow vehicle may de- crease overall stability. Therefore, to main- tain adequate control, reduce your speed and shift to a lower gear. Avoid long or repeated use of the brakes when descend- ing a hill, as this reduces their effectiveness and could cause overheating. Shifting to a lower gear instead provides “engine brak- ing” and reduces the need to brake as fre- quently.

● If the engine coolant temperature rises to a high temperature, refer to “If your vehicle overheats” in the “In case of emergency” section of this owner’s manual.

● Trailer towing requires more fuel than normal

circumstances.

9-34 Technical and consumer information

● Avoid towing a trailer for your vehicle’s first

500 miles (805 km).

● For the first 500 miles (805 km) that you do

tow, do not drive over 50 MPH (80 km/h).

● Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the “NISSAN Ser- vice and Maintenance Guide”.

● When making a turn, your trailer wheels will be closer to the inside of the turn than your vehicle wheels. To compensate for this, make a larger than normal turning radius during the turn.

● Crosswinds and rough roads will adversely affect vehicle/trailer handling, possibly caus- ing vehicle sway. When being passed by larger vehicles, be prepared for possible changes in crosswinds that could affect ve- hicle handling.

Do the following if the trailer begins to sway: 1. Take your foot off the accelerator pedal to allow the vehicle to coast and steer as straight ahead as the road conditions allow. This combination will help stabilize the ve- hicle – Do not correct trailer sway by steering or

applying the brakes.

2. When the trailer sway stops, gently apply the brakes and pull to the side of the road in a safe area.

3. Try to rearrange the trailer load so it is bal-

anced as described earlier in this section.

● Be careful when passing other vehicles. Passing while towing a trailer requires con- siderably more distance than normal pass- ing. Remember, the length of the trailer must also pass the other vehicle before you can safely change lanes.

● Downshift the transmission to a lower gear for engine braking when driving down steep or long hills. This will help slow the vehicle without applying the brakes.

● Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced braking efficiency.

● Increase your following distance to allow for greater stopping distances while towing a trailer. Anticipate stops and brake gradually. ● NISSAN recommends that the cruise con-

trol not be used while towing a trailer.

● After towing 500 miles (805 km), start and idle the engine with the transmission in Neu- tral for two minutes. Failure to idle the engine after every 500 miles (805 km) of towing may cause damage to internal transmission parts.

Automatic Transmission (if so equipped) To tow a vehicle equipped with an automatic transmission, an appropriate vehicle dolly MUST be placed under the towed vehicle’s drive wheels. Always follow the dolly manufacturer’s recommendations when using their product.

● Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers. Obey the local speed limits.

● Check your hitch, trailer wiring harness con- nections, and trailer wheel lug nuts after 50
miles (80 km) of travel and at every break.

● When launching a boat, don’t allow the wa- ter level to go over the exhaust tail pipe or rear bumper.

● Make sure you disconnect the trailer lights before backing the trailer into the water or the trailer lights may burn out.

When towing a trailer, final drive gear oil should be replaced and transmission oil/fluid should be changed more fre- quently. For additional information, see the “Maintenance and do-it-yourself” section earlier in this manual. FLAT TOWING Towing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home.

CAUTION

● Failure to follow these guidelines can result in severe transmission damage. ● Whenever flat towing your vehicle, al-

ways tow forward, never backward.

● DO NOT tow any automatic transmis- sion vehicle with all four wheels on the ground (flat towing). Doing so WILL DAMAGE internal transmission parts due to lack of transmission lubrication. ● For emergency towing procedures refer to “Towing recommended by NISSAN” in the “In case of emergency” section of this manual.

Manual Transmission (if so equipped) ● Always tow with the manual transmission in

Neutral.