2011 Nissan Armada Owners Manual

play just before the ignition switch is placed in the OFF position may con- tinue to be displayed.

● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display.

Average fuel economy (MPG or L/100 km) The Average Fuel Economy is calculated based on fuel consumption since the last reset. The display is updated every 30 seconds and 1/3 mi (500 m). After a reset or connecting the battery cables, the display might show (**.*). Resetting fuel economy The average fuel economy calculation can be reset to 0. Press the INFO button and select the “Fuel Economy” key, then select the “Reset” key using the NISSAN controller.

LHA0915

LHA0921

HOW TO USE THE INFO BUTTON Press the INFO button. The display screen shows vehicle information for your convenience. The information shown on the screen should be a guide to determine the condition of the vehicle. See the following for details.

Fuel economy Press the INFO button, then select the “Fuel Economy” key using the NISSAN controller and press the ENTER button to display Average Fuel Economy, Distance to Empty and Fuel Economy Record. Distance to empty (MI or km) The Distance to Empty (DTE) mode provides you with an estimation of the distance that can be driven before refueling. The DTE is constantly calculated based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. When the fuel level is low, the DTE display will change to (*).

Monitor, climate, audio, phone and voice recognition systems 4-5

Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of low tire pressure, a message is dis- played on the screen: LOW PRESSURE — Check All Tires.

WARNING

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the Tire Pressure Monitoring System (TPMS) will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

LHA0922

LHA0923

Fuel economy record Press the INFO button, then select the “Fuel Economy” key, then select the “View” key using the NISSAN controller. The average fuel consumption history will be displayed in a graph form along with the average fuel for the previous reset-to-reset period.

Tire pressure information (if so equipped) To display tire pressure information, press the INFO button, then select the “Tire Pressure” key using the NISSAN controller and press the EN- TER button.

Pressure indication in ** psi on the screen indi- cates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.

4-6 Monitor, climate, audio, phone and voice recognition systems

Resetting the trip computer Each item in the trip computer can be reset to 0. Select the “Reset” key on the item that needs to be reset using the NISSAN controller and press the ENTER button. To reset all of the items in the trip computer select the “Reset ALL” key and press the ENTER button. A confirmation screen will appear. Select the “Yes” key and press the ENTER button.

LHA0924

Trip computer Press the INFO button, then select the “Trip Computer” key using the NISSAN controller and press the ENTER button. The trip computer will display the following items: ● Elapsed Time – Journey time since the last reset up to a maximum of 99 hours and 59
minutes.

● Driving Distance – Distance driven (mile or

km) since the last reset.

● Average Speed – Average speed driven

(MPH or km/h) since the last reset.

LHA0925

Maintenance items Press the INFO button and select the “Mainte- nance” key using the NISSAN controller; the maintenance information will be displayed on the screen.

Monitor, climate, audio, phone and voice recognition systems 4-7

Resetting the maintenance interval To reset the reminder schedule (distance) to 0 mi (km), select the “Reset Distance” key using the NISSAN controller.

LHA0926

Changing the maintenance interval

Select one of the “Reminder (1 – 4)” keys using the NISSAN controller and press the ENTER button to display the screen to change the main- tenance interval.

Select the “Interval” key using the NISSAN con- troller and press the ENTER button. Use the NISSAN controller to change the maintenance interval. To accept the changes, press the BACK button.

4-8 Monitor, climate, audio, phone and voice recognition systems

LHA0839

Displaying the maintenance notice re- minder Select the “Interval Reminder ON” key to display the MAINTENANCE INFORMATION automati- cally at the set maintenance interval. The indica- tor light will illuminate when it is ON. The MAINTENANCE NOTICE screen will be au- tomatically displayed as shown when both of the following conditions are met: ● The vehicle is driven the set distance and the ignition switch is placed in the OFF position. ● The ignition switch is placed in the ON po- sition the next time the vehicle will be driven.

To return to the previous display after the MAIN- TENANCE NOTICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: ● The “Reset” key is selected. ● The “Interval Reminder ON” key is set to

OFF (indicator light not illuminated). ● The maintenance interval is set again.

LHA0927

WHA0937

Type A

HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the SET- TINGS screen will appear on the display. You can select and/or adjust several functions, features and modes that are available for your vehicle. Use the NISSAN controller to select each item to be set and press the ENTER button.

Type B

Monitor, climate, audio, phone and voice recognition systems 4-9

LHA0929

LHA0930

WHA0823

Display settings Select the “Display” key. The Display settings screen will appear.

Brightness/contrast: Select the “Brightness” key or the “Contrast” key to adjust the brightness or contrast of the map background. Use the NISSAN controller to adjust the brightness to darker or brighter and the con- trast to lower or higher. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.

Display off: Select the “Display ON” key. The amber indicator next to “Display ON” turns off and the message above will be displayed briefly. When the audio, HVAC (Heater and air conditioner), or any mode button on the control panel is operated, the dis- play turns on for that operation. If one of the control panel buttons is pressed, the display will not automatically turn off until that operation is finished. Otherwise, the screen turns off auto- matically after 5 seconds.

4-10 Monitor, climate, audio, phone and voice recognition systems

To turn the screen on: ● Press the SETTING button, select the “Dis- play” key and then select the “Display ON” key. Then set the screen to on by pressing the ENTER button, or

● Hold the

OFF button for approxi- mately 2 seconds and the message “resum- ing display” will appear and the “Display ON” key will be automatically turned on (no am- ber indicator).

Background color: Select the “Background Color” key; the display color changes between day and night. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.

LHA0931

LHA0932

Beeps settings Select the “Beeps” key and press the ENTER button. The Beeps settings screen will appear. With this option on (indicator light illuminated), a beep will sound if any control panel button is pressed.

Clock The following display will appear after pressing the SETTING button, then selecting the “Clock” key using the NISSAN controller and pressing the ENTER button. On-screen Clock:

When this item is enabled (indicator light illumi- nated), a clock is always displayed in the upper right corner of the screen. Clock Format:

Choose either the 12h (12–hour) clock display or the 24h (24–hour) clock display.

Monitor, climate, audio, phone and voice recognition systems 4-11

Daylight Savings Time: When this item is enabled (indicator light illumi- nated), daylight savings time is on. To turn off the daylight savings time, touch the “ON” key; the amber indicator light will disappear.

● Atlantic ● Newfoundland ● Aleutian ● Hawaii ● Alaska

LHA0933

Time Zone:

the “Time Zone” key;

Select screen will appear.

the Time Zone

Select one of the following zones, depending on the current location, by selecting the correct time zone key and pressing the ENTER button to enable that time zone (indicator light will illumi- nate for that location). ● Pacific ● Mountain ● Central ● Eastern

4-12 Monitor, climate, audio, phone and voice recognition systems

● OK:

Select to accept the changes made and return to the clock setting display.

After selection/settings, press the BACK button or any other mode button to accept the changes.

LHA0943

Clock Adjust:

Adjust the time by manually inputting the correct time. ● 0 – 9:

Select to change the number in the display.

● Modify:

Select to change the number at the cursor position.

● >:

Select to move the cursor position to the right.

● <:

Select to move the cursor position to the left.

LHA0938
Comfort & Convenience settings (if so equipped) Select the “Comfort & Conv.” key by using the NISSAN controller and pressing the ENTER but- ton. The comfort and convenience option screen will be displayed. You can set the following operating conditions by selecting the desired item using the NISSAN controller, then pressing the ENTER button. The indicator light (box at the right of the selected item) alternately turns on and off each time the ENTER button is pressed. Indicator light is illuminated — ON Indicator light is not illuminated — OFF

Monitor, climate, audio, phone and voice recognition systems 4-13

NOTE:

If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Auto Re-Lock Time: Select to set the length of time before doors automatically re-lock. Selective Door Unlock: When this item is turned on, only the driver’s door is unlocked first after the door unlock operation. When the door handle request switch on the driver’s or front passenger’s side door is pushed to be unlocked, only the corresponding door is unlocked first. All the doors can be unlocked if the door unlock operation is performed again within 1 minute.

When this item is turned to off, all the doors will be unlocked after the door unlock operation is performed once. Intelligent Key Lock / Unlock: Select to turn on or turn off the door lock/unlock function by pushing the door handle request switch. Intelligent Key Lock Reply: Select to change the sound of the Intelligent Key mode used when a door handle request switch is pushed to lock.

LHA0939
Auto Interior Illumination: Select to turn on or turn off the illumination of the interior lights when any door is unlocked. Auto Headlights Sensitivity: Select to adjust the sensitivity of the automatic headlights higher (right) or lower (left). Auto Headlights Off Delay: Select to change the duration of the automatic headlight off timer from 0-, 30-, 45-, 60-, 90-, 120-, 150- and 180-second periods. Speed Sensing Wiper Interval: Select to turn on or turn off the wiper interval adjusted automati- cally according to the vehicle speed.

LHA0940
Remote Key Response Horn: Select to turn on or turn off the horn beep mode used when the LOCK button on the keyfob is pressed.

NOTE:

If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Remote Key Response Lights: Select to turn on or turn off the hazard indicator flash mode used when the LOCK or UNLOCK button on the keyfob is pressed.

4-14 Monitor, climate, audio, phone and voice recognition systems

Select to turn off all sounds made when a door handle request switch is pushed, by selecting the “OFF” key. Intelligent Key Unlock Reply: Select to change the sound of the Intelligent Key mode used when a door handle request switch is pushed to unlock. Select to turn off all sounds made when a door handle request switch is pushed, by selecting the “OFF” key. Slide Driver Seat Back on Exit: Select to turn on or turn off the driver’s seat moving backward for easy exit when the ignition switch is in the OFF position and the driver’s door is opened. After getting into the vehicle and pushing the ignition switch to the ACC position, the driver’s seat moves to the previous position. Return All Settings to Default: Select to change all the comfort and convenience systems to their default settings.

LHA0934

LHA0935

Language / Units Use the NISSAN controller to select the “Lan- guage / Units” key. Select which setting you want to change using the NISSAN controller.

Select Language: Select the “English” key, the “Français” key or the “Español” key to change the language shown on the display.

Monitor, climate, audio, phone and voice recognition systems 4-15

OFF BUTTON

To change the display brightness, press OFF button. Pressing the button again the or the will change the display to the day display. The brightness can then be night adjusted using the NISSAN controller.

The display brightness can also be adjusted us- ing the + (brighter) button or the ⫺ (dimmer) button.

If no operation is done within 10 seconds, the display will return to the previous display.

OFF button for more Press and hold the than 2 seconds to turn the display off. Press the button again to turn the display on.

LHA0936

Select Units: Select the “US” (mi, °F, MPG) key or the “Metric” (km, °C, L/100 km) key to change the units shown on the display. Audio settings For audio settings, refer to “Audio System” in this section.

4-16 Monitor, climate, audio, phone and voice recognition systems

CONTROL PANEL BUTTONS — COLOR SCREEN WITH NAVIGATION SYSTEM (if so equipped)

1. STATUS button (P. 4-20)

2. DEST button*

3. NISSAN controller (P. 4-18)

4. PHONE button**

5.

LHA0880
OFF brightness control button

(P. 4-32)

6.

INFO button (P. 4-21)

7. SETTING button (P. 4-26)

8. VOICE button*

9. BACK (previous) button (P. 4-18) 10. ROUTE button* 11. ZOOM IN button* 12. MAP button* 13. ZOOM OUT button* *For Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. **For information on the PHONE button, see “Bluetooth姞 Hands-Free Phone System with Navigation System” later in this section. When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will discharge the battery, and the engine will not start. Reference symbols: ENTER button — This is a button on the control panel. “Display” key — This is a select key on the screen. By selecting this key, you can proceed to the next function.

Monitor, climate, audio, phone and voice recognition systems 4-17

If you press the BACK button 䊊4 during setup, the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. In some screens, pressing the BACK button 䊊4
accepts the changes made during setup. For the VOICE button 䊊5 functions, refer to the separate Navigation System Owner’s Manual. HOW TO USE THE TOUCH SCREEN

LHA0882

CAUTION

HOW TO USE THE NISSAN CONTROLLER Use the NISSAN controller to choose an item on the display screen. Highlight an item on the dis- play using the main directional buttons 䊊2 (cer- tain Navigation System functions use the addi- tional directional buttons 䊊6 ) or the center dial 䊊3 . Then press the ENTER button 䊊1 to select the item or perform the action. The BACK button 䊊4 has two functions: ● Go back to the previous display (cancel).

● The glass screen on the liquid crystal display may break if it is hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.

● To clean the display, never use a rough cloth, alcohol, benzine, thinner or any kind of solvent or paper towel with a chemical cleaning agent. They will scratch or deteriorate the panel.

4-18 Monitor, climate, audio, phone and voice recognition systems

● Do not splash any liquid such as water or car fragrance on the display. Contact with liquid will cause the system to malfunction.

To help ensure safe driving, some functions can- not be operated while driving. The on-screen functions that are not available while driving will be “grayed out” or muted. Park the vehicle in a safe location and then oper- ate the navigation system.

WARNING

● ALWAYS give your full attention to

driving.

● Avoid using vehicle features that could distract you. If distracted, you could lose control of your vehicle and cause an accident.

WHA0885

WHA0887

WHA0889

Touch screen operation With this system, the same operations as those for the NISSAN controller are possible using the touch screen operation. Selecting the item: Touch an item to select. To select the “Audio” key, touch the “Audio” key 䊊1 on the screen. Touch the “BACK” key 䊊2 to return to the previous screen.

Adjusting the item: Touch the “+” key 䊊1 or the “⫺” key 䊊2 to adjust the settings. Touch the “UP” key 䊊3 to scroll up to the previous page, or touch the “DOWN” key 䊊4
to scroll down to next page.

Inputting characters: Touch the letter or number key 䊊1 . There are some options available when inputting characters. ● Uppercase:

Shows uppercase characters.

● Lowercase:

Shows lowercase characters.

● Space:

Inserts a space.

Monitor, climate, audio, phone and voice recognition systems 4-19

● Symbols:

Shows symbols such as the question mark (?).

● Delete:

Deletes the last inputted character with one touch. Touch and hold the “Delete” key to delete all of the characters.

● OK:

Completes the character input.

Touch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or de- tergent. Dampen the cloth first, and then wipe the screen. START-UP SCREEN When you place the ignition switch in the ACC or ON position, the SYSTEM START-UP warning is displayed on the screen. When you read and agree with the warning, press the ENTER button. If you do not push the ENTER button, you will not be able to use the navigation system. To proceed to the next step, refer to the separate Navigation System Owner’s Manual.

menu screen (for example, Auto Interior Illu- mination, etc.).

3. UP/DOWN Movement Indicator:

Shows that the NISSAN controller may be used to move UP/DOWN on the screen and select more options.

4. Screen Count:

Shows the number of menu selections avail- able for that screen (for example, 1/14).

5. Footer/Information Line:

Provides more information (if available) about the menu selection currently high- lighted (for example, Cabin lighting when unlocking doors).

HOW TO USE THE STATUS BUTTON To display the status of the audio, climate control system, fuel consumption and navigation system, press the STATUS button. The following information will appear when the STATUS button is pressed: Audio → Audio and climate control system → Audio, climate control temperature settings, av- erage fuel economy and distance to empty → Audio, climate control temperature settings and Navigation System → Audio

LHA0890
HOW TO SELECT MENUS ON THE SCREEN Vehicle functions are viewed on the center dis- play screen in menus. Whenever a menu selec- tion is made or menu item is highlighted, different areas on the screen provide you with important information. See the following for details. 1. Header:

Shows the path used to get to the current screen (for example, press the SETTING button > then select the “Comfort & Conv.” key).

2. Menu Selections:

Shows the options to choose within that

4-20 Monitor, climate, audio, phone and voice recognition systems

NOTE:

● If the amount of fuel added while the ignition switch is OFF is small, the dis- play just before the ignition switch is placed in the OFF position may con- tinue to be displayed.

● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display.

Average fuel economy (MPG or L/100 km) The Average Fuel Economy is calculated based on fuel consumption since the last reset. The display is updated every 30 seconds and 1/3 mi (500 m). After a reset or connecting the battery cables, the display might show (**.*). Resetting fuel economy The average fuel economy calculation can be reset to 0. Press the INFO button and select the “Fuel Economy” key, then select the “Reset” key using the NISSAN controller and press the EN- TER button.

LHA0892

LHA0893

HOW TO USE THE INFO BUTTON Press the INFO button; the display screen shows vehicle and navigation information for your con- venience. The information shown on the screen should be a guide to determine the condition of the vehicle. See the following for details.

Fuel economy Press the INFO button, then select the “Fuel Economy” key using the NISSAN controller and press the ENTER button to display Average Fuel Economy, Distance to Empty and Fuel Economy Record. Distance to empty (MI or km) The Distance to Empty (DTE) mode provides you with an estimation of the distance that can be driven before refueling. The DTE is constantly calculated based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. When the fuel level is low, the DTE display will change to (*).

Monitor, climate, audio, phone and voice recognition systems 4-21

Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of low tire pressure, a message is dis- played on the screen: LOW PRESSURE — Check All Tires.

WARNING

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the Tire Pressure Monitoring System (TPMS) will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

LHA0894

LHA0895

Fuel economy record Press the INFO button, then select the “Fuel Economy” key, then select the “View” key using the NISSAN controller and press the ENTER button. The average fuel consumption history will be displayed in a graph form along with the average fuel for the previous Reset-to-Reset period.

Tire pressure information To display tire pressure information, press the INFO button, then select the “Tire Pressure” key using the NISSAN controller and press the EN- TER button.

Pressure indication in ** psi on the screen indi- cates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.

4-22 Monitor, climate, audio, phone and voice recognition systems

Resetting the trip computer Each item in the trip computer can be reset to 0. Select the “Reset” key on the item that needs to be reset using the NISSAN controller and press the ENTER button. To reset all of the items in the trip computer select the “Reset ALL” key and press the ENTER button. A confirmation screen will appear; select the “Yes” key and press the ENTER button.

LHA0896

Trip computer Press the INFO button, then select the “Trip Computer” key using the NISSAN controller and press the ENTER button. The trip computer will display the following items: ● Elapsed Time – Journey time since the last reset up to a maximum of 99 hours and 59
minutes.

● Driving Distance – Distance driven (miles or

km) since the last reset.

● Average Speed – Average speed driven

(MPH or km/h) since the last reset.

LHA0897

Maintenance items Press the INFO button and select the “Mainte- nance” key using the NISSAN controller; the maintenance information will be displayed on the screen.

Monitor, climate, audio, phone and voice recognition systems 4-23

Resetting the maintenance interval To reset the reminder schedule (distance) to 0 mi (km), select the “Reset Distance” key using the NISSAN controller.

LHA0898

Changing the maintenance interval

Select one of the “Reminder (1 – 4)” keys using the NISSAN controller and press the ENTER button to display the screen to change the main- tenance interval.

Select the “Interval” key using the NISSAN con- troller and press the ENTER button. Use the NISSAN controller to change the maintenance interval. To accept the changes, press the BACK button.

4-24 Monitor, climate, audio, phone and voice recognition systems

LHA0839

Displaying the maintenance notice re- minder Select the “Interval Reminder ON” key to display the MAINTENANCE INFORMATION automati- cally at the set maintenance interval. The indica- tor light will illuminate when it is ON. The MAINTENANCE NOTICE screen will be au- tomatically displayed as shown when both of the following conditions are met: ● The vehicle is driven the set distance and the ignition switch is placed in the OFF position. ● The ignition switch is placed in the ON po- sition the next time the vehicle will be driven.

To return to the previous display after the MAIN- TENANCE NOTICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: ● The “Reset” key is selected. ● The “Interval Reminder ON” key is set to

OFF (indicator light not illuminated). ● The maintenance interval is set again.

Traffic Info Refer to the separate Navigation System Own- er’s Manual for information regarding this item. Where am I? Refer to the separate Navigation System Own- er’s Manual for information regarding this item. GPS Satellite Info. Refer to the separate Navigation System Own- er’s Manual for information regarding this item.

LHA0908

Other items Press the INFO button and select the “Others” key using the NISSAN controller and press the ENTER button to view information on the naviga- tion and voice recognition systems. Voice Recognition

For Voice Recognition settings, refer to “NISSAN Voice Recognition system” in this section. Navigation version

Refer to the separate Navigation System Own- er’s Manual for information regarding this item.

Monitor, climate, audio, phone and voice recognition systems 4-25

LHA0884

LHA0901

LHA0902

HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the Set- tings screen will appear on the display. You can select and/or adjust several functions, features and modes that are available for your vehicle. Use the NISSAN controller to select each item to be set.

Display settings Select the “Display” key and press the ENTER button. The Display settings screen will appear.

Brightness/contrast: Select the “Brightness” key or the “Contrast” key to adjust the brightness or contrast of the display background. Use the NISSAN controller to adjust the brightness to darker or brighter and the con- trast to lower or higher. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.

4-26 Monitor, climate, audio, phone and voice recognition systems

To turn the screen on: ● Press the SETTING button and select the “Display” key and then select the “Display ON” key. Then set the screen to on by press- ing the ENTER button, or

● Hold the

OFF button for approxi- mately two seconds and the message “re- suming display” will appear and the “Display ON” key will be automatically turned on (no amber indicator). Background color: Select the “Background Color” key; the display color changes between day and night. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.

WHA0823

Display off: Select the “Display ON” key. The indicator of the “Display ON” turns amber and the message above will be displayed briefly. When the audio, HVAC (Heater and air conditioner), or any mode button on the control panel is operated, the dis- play turns on for that operation. If one of the control panel buttons is pressed, the display will not automatically turn off until that operation is finished. Otherwise, the screen turns off auto- matically after five seconds.

LHA0904

Clock The following display will appear after pressing the SETTING button, then selecting the “Clock” key using the NISSAN controller and pressing the ENTER button. On-screen Clock: When this item is enabled (indicator light illumi- nated), a clock is always displayed in the upper right corner of the screen. This clock will indicate the time almost exactly because it is always adjusted by the GPS system.

Monitor, climate, audio, phone and voice recognition systems 4-27

● Atlantic ● Newfoundland ● Hawaii ● Alaska After selection/settings, press the BACK button or any other mode button to accept the changes.

Clock Format: Choose either the 12h (12–hour) clock display or the 24h (24–hour) clock display. Offset Adjust: Adjust the time by increasing or decreasing per minute. Daylight Saving Time: When this item is enabled (indicator light illumi- nated), daylight saving time is on. To turn off the daylight saving time, touch the “ON” key; the amber indicator light will disappear.

LHA0905

Time Zone:

the “Time Zone” key;

Select screen will appear.

the Time Zone

Select one of the following zones, depending on the current location, by selecting the correct time zone key and pressing the ENTER button to enable that time zone (indicator light will illumi- nate for that location). ● Pacific ● Mountain ● Central ● Eastern

4-28 Monitor, climate, audio, phone and voice recognition systems

WHA1203

Comfort & Convenience settings Select the “Comfort & Conv.” key by using the NISSAN controller and pressing the ENTER but- ton. The comfort and convenience option screen will be displayed.

You can set the following operating conditions by selecting the desired item using the NISSAN controller, then pressing the ENTER button. The indicator light (box at the right of the selected item) alternately turns on and off each time the ENTER button is pressed.

Indicator light is illuminated — ON Indicator light is not illuminated — OFF

WHA1204
Auto Interior Illumination: Select to turn on or turn off the illumination of the interior lights when any door is unlocked. Auto Headlights Sensitivity: Select to adjust the sensitivity of the automatic headlights higher (right) or lower (left). Auto Headlights Off Delay: Select to change the duration of the automatic headlight off timer from 0, 30, 45, 60, 90, 120, 150 and 180 second periods. Speed Sensing Wiper Interval: Select to turn on or turn off the wiper interval adjusted automati- cally according to the vehicle speed.

WHA1205
Remote Key Response Horn: Select to turn on or turn off the horn chirp mode used when the LOCK button on the keyfob is pressed.

NOTE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Monitor, climate, audio, phone and voice recognition systems 4-29

Remote Key Response Lights: Select to turn on or turn off the hazard indicator flash mode used when the LOCK or UNLOCK button on the keyfob is pressed.

NOTE:

If you change the horn beep or the light flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Auto Re-Lock Time: Select to set the length of time before doors automatically re-lock. Selective Door Unlock: When this item is turned on, only the driver’s door is unlocked first after the door unlock operation. When the door handle request switch on the driver’s or front passenger’s side door is pushed to be unlocked, only the corresponding door is unlocked first. All the doors can be unlocked if the door unlock operation is performed again within one minute.

When this item is turned to off, all the doors will be unlocked after the door unlock operation is performed once. Intelligent Key Lock / Unlock: Select to turn on or turn off the door lock/unlock function by pushing the door handle request switch.

Intelligent Key Lock Reply: Select to change the sound of the Intelligent Key mode used when a door handle request switch is pushed to lock. Select to turn off all sounds made when a door handle request switch is pushed, by selecting the “OFF” key. Intelligent Key Unlock Reply: Select to change the sound of the Intelligent Key mode used when a door handle request switch is pushed to unlock. Select to turn off all sounds made when a door handle request switch is pushed, by selecting the “OFF” key. Slide Driver Seat Back on Exit: Select to turn on or turn off the driver’s seat moving backward for easy exit when the ignition switch is in the OFF position and the driver’s door is opened. After getting into the vehicle and placing the ignition switch in the ACC position, the driver’s seat moves to the previous position. Return All Settings to Default: Select to change all the comfort and convenience systems to their default settings.

4-30 Monitor, climate, audio, phone and voice recognition systems

LHA0909

Others settings Select the “Others” key using the NISSAN con- troller. Voice recognition, language and units set- ting screen will be displayed. Voice Recognition: For Voice Recognition settings, refer to “NISSAN Voice Recognition system” later in this section.

LHA0911

LHA0912

LHA0913

Language / Units: Use the NISSAN controller to select the “Lan- guage / Units” key and press the ENTER button. Select which setting you want to change using the NISSAN controller and selecting either the “Select Language” key or the “Select Units” key by pressing the ENTER button.

Select Language: Select the “English” key or the “Français” key to change the language shown on the display. If you select the “Français” key, French language will be displayed so please use the French Own- er’s Manual. To obtain a French Owner’s Manual, please see “Owner’s Manual/Service Manual Or- der Information” in the “Technical and consumer information” section.

Select Units:

Select the “US” (mi, °F, MPG) key or the “Metric” (km, °C, L/100 km) key to change the units shown on the display. Audio settings For audio settings, refer to “Audio System” in this section. Navigation settings Refer to the separate Navigation System Own- er’s Manual for information regarding these set- tings.

Monitor, climate, audio, phone and voice recognition systems 4-31

Volume and beeps settings Navigation volume For navigation volume settings refer to the sepa- rate Navigation System Owner’s Manual for infor- mation regarding these settings. Phone volume For phone volume settings refer to “Bluetooth姞 Hands-Free Phone System With Navigation Sys- tem” later in this section.

OFF BUTTON

To change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display. The brightness can then be adjusted using the NISSAN controller. If no operation is performed within 10 seconds, the display will return to the previous display.

OFF button for more Press and hold the than two seconds to turn the display off. Press the button again to turn the display on.

WHA0903

Beep setting With this option on (indicator light illuminated), a beep will sound if any control panel button is pressed. Phone settings For phone settings refer to “Bluetooth姞 Hands- Free Phone System With Navigation System” later in this section.

4-32 Monitor, climate, audio, phone and voice recognition systems

REARVIEW MONITOR (if so equipped)

When the shift selector is shifted into the R (Reverse) position, the monitor display shows the view directly to the rear of the vehicle.

WARNING

● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground.

● The RearView Monitor is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly.

● Objects viewed in the RearView Moni- tor differ from actual distance because a wide-angle lens is used.

● Make sure that the lift gate is securely

closed when backing up.

● Do not put anything on the rearview camera. The rearview camera is in- stalled beside the lift gate handle.

● When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, water may enter the camera unit causing wa- ter condensation on the lens, a mal- function, fire or an electric shock.

● Do not strike the camera. It is a preci- sion instrument. Otherwise, it may mal- function or cause damage resulting in a fire or an electric shock.

CAUTION

There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from the cover. HOW TO READ THE DISPLAYED LINES Lines which indicate the vehicle clearance and distances to objects with reference to the bumper line 䊊A are displayed on the monitor.

LHA0437
They are indicated as reference distances to objects. The lines and colors in the display indi- cate distances from the back bumper line 䊊A in the illustration. 䊊1 1.5 ft (0.5 m) red 䊊2 3 ft (1 m) yellow 䊊3 7 ft (2 m) green 䊊4 10 ft (3 m) green The vehicle clearance lines are wider than the actual clearance.

Monitor, climate, audio, phone and voice recognition systems 4-33

OPERATING TIPS ● When the shift selector is shifted to R (Re- verse), the monitor screen automatically changes to the RearView Monitor mode. However, the radio can be heard.

● It may take some time until the RearView Monitor is displayed after the shift selector has been shifted to R (Reverse). Objects may be distorted momentarily until the Rear- View Monitor screen is displayed com- pletely. When the shift selector is returned to a position other than R (Reverse), it may take some time until the screen changes. Objects on the screen may be distorted until they are completely displayed.

● When the temperature is extremely high or low, the screen may not clearly display ob- jects. This is not a malfunction.

● When strong light directly enters the cam-

era, objects may not be displayed clearly.

● Vertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction. ● The screen may flicker under fluorescent

light. This is not a malfunction.

● The colors of objects on the RearView Moni- tor may differ somewhat from those of the actual object.

● When the contrast of objects is low at night, pressing the SETTING button may not change the brightness.

● Objects on the monitor may not be clear in a

dark place or at night.

● If dirt, rain or snow attaches to the camera, the RearView Monitor may not display ob- jects. Clean the camera.

● Do not use alcohol, benzine or thinner to clean the camera. This will cause discolora- tion. To clean the camera, wipe with a cloth dampened with a diluted mild cleaning agent and then wipe with a dry cloth.

● Do not damage the camera as the monitor

screen may be adversely affected.

● Do not use body wax on the camera window. If body wax does get on the camera window, wipe off the wax with a clean cloth damp- ened with mild detergent diluted with water.

LHA1021

ADJUSTING THE SCREEN To adjust the quality of the screen, press the SETTING button. ● To adjust the Display ON/OFF, Brightness, Tint, Color, Contrast, and Black Level of the RearView Monitor, press the SETTING but- ton with the RearView Monitor on, then touch one of the adjustment keys. Press the “–” or “+” key on the item and adjust the level.

● Do not adjust the Brightness, Contrast, Tint and Color of the RearView Monitor while the vehicle is moving.

4-34 Monitor, climate, audio, phone and voice recognition systems

VENTS

Adjust air flow direction for the driver’s and pas- senger’s side vents 䊊1 , center vents 䊊2 , and rear passengers’ vents 䊊3 and 䊊4 by moving the vent slide and/or vent assemblies. For the driver’s and passenger’s side vents䊊1 , open or close by using the dial. Move the dial position to open the vents or toward the toward the position to close them.

LHA1030

Monitor, climate, audio, phone and voice recognition systems 4-35

HEATER AND AIR CONDITIONER (automatic)

1.

Driver’s temperature control dial/AUTO button A/C ON/OFF button Fan speed control (increase) Front window defroster button

2. 3. 4. 5. MODE button 6.

Passenger’s temperature control dial/ DUAL button System OFF Fan speed control (decrease) Rear window defroster button

7. 8. 9. 10. Air recirculation button

● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION Cooling or heating (auto) This mode may be normally used all year round as the system automatically works to keep a con- stant temperature. Air flow distribution and fan speed are also controlled automatically.

1. Press the AUTO button on. (AUTO will be

displayed.)

2. Turn the driver’s side temperature control dial to the left or right to set the desired temperature. Driver and passenger tem- peratures can be set independently. Press DUAL to activate dual climate control func- tions. Turn the passenger’s side temperature control dial to the left or right to set the desired passenger’s temperature.

● Adjust the temperature dial to about 75°F

(24°C) for normal operation.

LHA0859

WARNING

● The air conditioner cooling function op- erates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

4-36 Monitor, climate, audio, phone and voice recognition systems

● The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically.

● A visible mist may be seen coming from the vents in hot, humid conditions as the air is cooled rapidly. This does not indicate a mal- function.

Dehumidified defrosting or defogging

1. Press the defroster control button

to turn the system on. The display will show the defrost icon.

2. Turn the temperature dial to the left or right

to set the desired temperature.

● To quickly remove ice from the outside of the windows, press the fan control speed button until it reaches the maximum speed ● As soon as possible after the windshield is clean, press the AUTO button to return to the auto mode.

● When the defroster control button

is activated, the air conditioner will automati- cally be turned on at outside temperatures above 36°F (2°C). If in defrost mode for more than one minute, the air conditioning system will continue to operate until the fan control is turned OFF, the vehicle is shut off, or the A/C button is pressed even if the air flow MODE control button is used to select a position. This position other than the dehumidifies the air which helps defog the windshield. The air recirculation mode auto- matically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

MANUAL OPERATION Fan speed control buttons

Press the fan speed control buttons to manually control the fan speed.

+ / –

Press OFF to turn the system off.

Press the AUTO button to return to automatic control of the fan speed.

Air recirculation mode automatically turns off, allowing The outside air to be drawn into the passenger com- partment to prevent fogging in defrost, floor or def/floor modes.

to recir- Push the air recirculation button culate interior air inside the vehicle. Push the AUTO button to return to automatic mode. Air flow control Pressing the MODE button manually controls air flow and selects the air outlet:

— Air flows from center and side

vents.

— Air flows from center and side

vents and foot outlets.

— Air flows mainly from foot outlets. — Air flows from defroster and foot

outlets.

— Air flows from defroster outlets.

To turn system off Press the OFF button.

Monitor, climate, audio, phone and voice recognition systems 4-37

REAR SEAT AIR CONDITIONER

OPERATING TIPS ● When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant tempera- ture warms up, air flow from the foot outlets will operate normally.

LIC0836
The sunload sensor 䊊1 , located on the top center of the instrument panel, helps the system main- tain a constant temperature. Do not put anything on or around this sensor.

LHA0863
Rear seat temperature and fan speed can be controlled from both the front seat overhead con- sole controls 䊊A or the rear seat overhead con- sole controls 䊊B . Press the REAR CTRL button to transfer control of the rear climate functions to the rear passen- gers. To operate the rear air conditioner, the engine must be running. If the rear seat fan control dial is set to (0), the air conditioner is turned off. If it is set to any of the fan speed positions, air is discharged from the rear vents at the corresponding speed.

4-38 Monitor, climate, audio, phone and voice recognition systems

SERVICING AIR CONDITIONER

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See “Air conditioner system refrigerant and oil recommendations” in the “Technical and consumer information” section of this manual. A NISSAN dealer is able to service your “environ- mentally friendly” air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

1. 2. 3.

Rear fan speed control dial Rear airflow mode buttons Rear temperature control dial

LHA0861

WHA1129

CONTROLS Fan control dial The fan control dial turns the rear vent fan on and off and controls fan speed. Airflow mode buttons The airflow mode buttons select where the air flow is directed from. Temperature control dial The temperature control dial allows rear passen- gers to adjust the temperature of the outlet air.

Monitor, climate, audio, phone and voice recognition systems 4-39

AUDIO SYSTEM

RADIO Place the ignition switch in the ACC or ON position and press the VOL (volume)/ON·OFF (power) knob to turn the radio on. If you listen to the radio with the engine not running, the ignition switch should be placed in the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However, there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the de- vice in a different location may reduce or elimi- nate the noise. FM RADIO RECEPTION Range: FM range is normally limited to 25 – 30 mi (40 – 48 km), with monaural (single channel) FM having slightly more range than stereo FM. Exter- nal influences may sometimes interfere with FM station reception even if the FM station is within 25 mi (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line- of-sight path, exhibiting many of the same char- acteristics as light. For example, they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter), static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.

4-40 Monitor, climate, audio, phone and voice recognition systems

SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is used for the first time or the battery has been replaced, the satellite radio may not work properly. This is not a mal- function. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. The satellite radio mode will be skipped unless an optional satellite receiver and antenna are in- stalled and an XM姞* satellite radio service sub- scription is active. Satellite radio is not available in Alaska, Hawaii and Guam. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. A build up of ice on the satellite radio antenna can affect satellite radio performance. Remove the ice to restore satellite radio reception. * XM姞 is a registered trademark of XM Satellite Radio, Inc.

Compact disc (CD) player

CAUTION

● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

● Trying to load a CD with the CD door closed could damage the CD and/or CD changer.

● Only one CD can be loaded into the CD

player at a time.

● Only use high quality 4.7 in (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging.

● During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

● The player may skip while driving on

rough roads.

LHA0099
AUDIO OPERATION PRECAUTIONS

● The CD player sometimes cannot func- tion when the compartment tempera- ture low. Decrease/increase the temperature before use.

extremely high or

is

Monitor, climate, audio, phone and voice recognition systems 4-41

● Do not expose the CD to direct sun-

light.

● CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

● The following CDs may not work prop-

erly: ● Copy control compact discs (CCCD) ● Recordable compact discs (CD-R) ● Rewritable compact discs (CD-RW) ● Do not use the following CDs as they may cause the CD player to malfunc- tion: ● 3.1 in (8 cm) discs with an adapter ● CDs that are not round ● CDs with a paper label ● CDs that are warped, scratched, or

have abnormal edges

● This audio system can only play pre- recorded CDs. It has no capability to record or burn CDs.

● If the CD cannot be played, one of the following messages will be displayed.

CHECK DISC:

● Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).

● Confirm that the CD is not bent or

warped and it is free of scratches.

PRESS EJECT:

This is an error due to excessive tem- perature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal.

UNPLAYABLE:

The file is unplayable in this audio sys- tem (only MP3 or WMA (if so equipped) CD).

CompactFlash姞 (CF) player (if so equipped) ● Do not force a CF card into the slot. This

could damage the CF card and/or player.

● During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CF card and dehumidify or ventilate the player completely.

● The CF player sometimes cannot function when the passenger compartment tempera- ture is extremely high. Decrease the tem- perature before use.

● Do not expose a CF card to direct sunlight. ● Confirm that a CF card is inserted correctly. Compact Disc (CD)/CompactFlash姞 (CF) with MP3 or WMA (if so equipped) Terms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD/CF can reduce the file size by approximately 10:1 ratio (Sampling: 44.1 kHz, Bit rate: 128 kbps) with virtually no perceptible loss in quality. MP3 compres- sion removes the redundant and irrelevant parts of a sound signal that the human ear doesn’t hear.

4-42 Monitor, climate, audio, phone and voice recognition systems

● WMA — Windows Media Audio (WMA)* is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.

● Bit rate — Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.

● Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second.

● Multisession — Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.

● ID3/WMA Tag — The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, album title, encoding bit rate, track time duration, etc. ID3 tag information is displayed on the Album/Artist/Track title line on the display.

* Windows姞 and Windows Media姞 are regis- tered trademarks and trademarks of the Mi- crosoft Corporation in the United States of America and/or other countries. CompactFlash姞 is a registered trademark of the SanDisk姞 Corporation in the United States of America and/or other countries.

WHA1078

Playback order chart

Playback order: Music playback order of a CD/CF with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or

WMA files are not shown in the display.

Monitor, climate, audio, phone and voice recognition systems 4-43

● If there is a file in the top level of the disc,

“Root Folder” is displayed.

● The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

4-44 Monitor, climate, audio, phone and voice recognition systems

Specification chart:

Supported media

Supported file systems

Supported versions*1

MP3

WMA*2

Tag information

Folder levels

Version Sampling frequency Bit rate Version Sampling frequency Bit rate

Text character number limitation

Displayable character codes*3

CD, CD-R, CD-RW, CF CD, CD-R, CD-RW: ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. CompactFlash card: FAT12, FAT16, FAT32
MPEG1, MPEG2, MPEG2.5
8 kHz - 48 kHz 8 kbps - 320 kbps, VBR*4
WMA7, WMA8, WMA9
32 kHz - 48 kHz 32 kbps - 192 kbps, VBR*4
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER 2.4 (MP3 only) WMA tag (WMA only) With navigation system: Folder levels: 8, Folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder) Without navigation system: Folder levels: 8, Folders and files: 999 (Max. 255 files for one folder) With navigation system: 128 characters Without navigation system: 64 characters 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.

*2 Protected WMA files (DRM) cannot be played.

*3 Available codes depend on what kind of media, versions and information are going to be displayed.

*4 When VBR files are played, the playback time may not be displayed correctly.

Monitor, climate, audio, phone and voice recognition systems 4-45

Troubleshooting guide:

Symptom

Cannot play

Poor sound quality It takes a relatively long time before the music starts playing.

Music cuts off or skips

Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order

Cause and Countermeasure

Check if the CD/CF was inserted correctly. Check if the CD/CF is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the player will play correctly after it returns to the normal temperature. If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played. Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number of characters for folder names and file names should be in compliance with the specifications. Check if the disc or the file is generated in an irregular format. This may occur depending on the variation or the setting of MP3/WMA writing applica- tions or other text editing applications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the CD/CF is protected by copyright. Check if the CD/CF is scratched or dirty. If there are many folders or file levels on the MP3/WMA CD/CF, or if it is a multisession disc, some time may be required before the music starts playing.

The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data.

When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, .“mp3”or “.wma”, or when play is prohibited by copyright protection, the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

4-46 Monitor, climate, audio, phone and voice recognition systems

1. 2. 3. 4. 5. 6.

RADIO AM·FM button* PRESET A·B·C button RPT button

speaker control button

RDM button PAUSE·MUTE button

REAR CTRL button SCAN button TRACK button

7. 8. 9. 10. SEEK/CAT button 11. TUNE/FLDR and AUDIO control knob 12.

CD load button

LHA0944

13. Station and CD select (1 - 6) buttons 14. 15. VOL/ON·OFF control knob 16. DISC·AUX button

CD eject button

Monitor, climate, audio, phone and voice recognition systems 4-47

*When the RADIO AM·FM button is pressed, the satellite radio mode will be skipped unless an optional satellite re- ceiver and antenna are installed and an XM姞 satellite radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam.

Turn the VOL/ON·OFF control knob to adjust the volume. This vehicle has Speed Sensitive Volume (SSV) for audio. The audio volume changes as the driv- ing speed changes. AUDIO control knob (Bass, Treble, Bal- ance and Fade): Push the AUDIO control knob to change the mode as follows: Bass → Treble → Balance → Fade To adjust Bass, Treble, Balance and Fade, push the AUDIO control knob until the desired mode appears in the display. Turn the tuning knob to adjust Bass and Treble to the desired level. You can also use the tuning knob to adjust Fade and Balance modes. Fade adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. Once you have adjusted the sound quality to the desired level, push the AUDIO control knob re- peatedly until the radio or CD display reappears. Otherwise, the radio or CD display will automati- cally reappear after about 10 seconds.

FM/AM/SAT RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) For all operation precautions, see “Audio opera- tion precautions” earlier in this section. The satellite radio mode will be skipped unless an optional satellite receiver and antenna are in- stalled and an XM姞 satellite radio service sub- scription is active. Satellite radio is not available in Alaska, Hawaii and Guam. Audio main operation VOL/ON·OFF control: Place the ignition switch in the ACC or ON position and then push the VOL/ON·OFF control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. To turn the system off, press the VOL/ON·OFF control knob. 4-48 Monitor, climate, audio, phone and voice recognition systems

LHA0927

Speed Sensitive Volume (SSV):

To change the SSV mode from OFF to 5, press the SETTING button. Then select the “Audio” key using the NISSAN controller, then press the EN- TER button. The audio settings screen will be displayed. Select the “–” key or “+” key, then press the ENTER button to change the SSV.

While in this screen you can also adjust the other audio settings by selecting the corresponding key.

Once you have adjusted the sound quality to the desired level, press the BACK button.

While in this screen, you can also adjust the other audio settings by selecting the corresponding key. Once you have adjusted the sound quality to the desired level, press the BACK button. For information on how to use the NISSAN con- troller, see “How to use the NISSAN controller” earlier in this section. Clock set: For setting the clock, see “Clock” under the “Control panel buttons – color screen without navigation system” heading earlier in this section.

WHA0941
For information on how to use the NISSAN con- troller, see “How to use the NISSAN controller” earlier in this section.

WHA0928

Precision phased audio (if so equipped):

To turn on or off the precision phased audio, press the SETTING button. Select the “Audio” key using the NISSAN controller, then press the ENTER button, the audio settings screen will be displayed. Select the “Precision Phased Audio” key, then press the ENTER button. If the amber indicator light is displayed, the precision phased audio is enabled. Pressing the ENTER button again will turn off the precision phased audio, the indicator light will disappear.

When this item is turned on, super high pitch sound and super low pitch sound are empha- sized and midrange sound is played naturally.

Monitor, climate, audio, phone and voice recognition systems 4-49

PAUSE·MUTE button:

To mute or pause the audio sound, press the PAUSE·MUTE button.

Press the PAUSE·MUTE button again to resume the audio sound. FM/AM/SAT radio operation FM/AM/SAT band select:

Pressing the RADIO AM·FM button will change the band as follows: AM ←→ FM or SAT* (satellite, if so equipped) When the RADIO AM·FM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played.

The last station played will also come on when the VOL/ON·OFF control knob is pressed ON.

*When the RADIO AM·FM button is pressed, the satellite radio mode will be skipped unless an optional satellite receiver and antenna are in- stalled and an XM姞 satellite radio service sub- scription is active. Satellite radio is not available in Alaska, Hawaii and Guam. If a compact disc is playing when the RADIO AM·FM button is pressed, the compact disc will automatically be turned off and the last radio station played will come on.

WHA0946

WHA0947
● Song displays the ID3 encoded tag of the

CD/MP3 display mode

While listening to a CD or an MP3/WMA CD certain text might be able to be displayed (when CD encoded with text is being used).

Depending on how the CD or MP3/WMA CD is encoded the following text might be able to be displayed by selecting the “Text” key using the NISSAN controller and pressing the ENTER but- ton: ● Folder displays the name of

the current

folder being accessed.

● File displays the name of the file currently

playing.

song name.

● Album displays the ID3 encoded tag of the

album name.

● Artist displays the ID3 encoded tag of the

artist’s name.

● Disc displays the disc name of the CD cur-

rently playing.

● Track displays the name of the song on the

CD currently playing.

Some of this text or modes might not display while playing a regular CD. Press the BACK button to exit the CD text display screen.

4-50 Monitor, climate, audio, phone and voice recognition systems

The FM stereo indicator ST will illuminate during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. TUNE/FLDR (Tuning) knob:

To manually tune the radio, turn the TUNE/FLDR knob to the right or left.

SEEK/CAT and TRACK tuning buttons:

button or

Press the SEEK/CAT the button for less than 1.5 seconds TRACK to tune from high to low or low to high frequen- cies and stop at the next broadcasting station. SCAN tuning:

Press the SCAN button to stop at each broad- casting station for 5 seconds. Pressing the SCAN button again during this 5 second period will stop scan tuning and the radio will remain tuned to that station. If the SCAN button is not pressed within 5 seconds, scan tuning moves to the next station.

PRESET A·B·C (Station memory opera- tions):

18 stations can be set for the FM, AM and SAT (satellite, if so equipped) radio to the A, B and C preset button in any combination of FM, AM or SAT stations.

1. Choose preset bank A, B or C using the

PRESET A·B·C select button.

2. Select the desired FM, AM or SAT station

band.

3. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 – 6) until a beep sound is heard.

4. The channel indicator will then come on and the sound will resume. Programming is now complete.

5. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected, or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band). Cur-

rently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: ● Station call sign, such as “WHFR 98.3”. ● Station name, such as “The Groove”. ● Music or programming type such as “Clas-

sical”, “Country”, or “Rock”. ● Artist and song information. If the station broadcasts RDS information, the RDS icon is displayed. Compact disc (CD) changer operation Place the ignition switch in the ACC or ON button, then press position and press the one of the CD insert (1–6) slots. Insert the com- pact disc into the slot with the label side facing up. The compact disc will be guided automati- cally into the slot and start playing.

If the radio is already operating, it will automati- cally turn off and the compact disc will play.

disc was

If the system has been turned off while the com- pact the VOL/ON·OFF control knob will start the compact