2011 Nissan Armada Owners Manual

Download PDF Manual
The high beam indicator light also comes on when the passing signal is activated. Malfunction Indicator Light (MIL) If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction. The Malfunction Indicator Light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 gallons (11.4 liters) of fuel in the fuel tank. light should After a few driving trips, the turn off if no other potential emission control system malfunction exists. If this indicator light comes on steady for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control sys- tem inspection/maintenance test. See “Readi- ness for inspection/maintenance (I/M) test” in the “Technical and consumer information” section of this manual. Operation The Malfunction Indicator Light will come on in one of two ways: ● Malfunction Indicator Light on steady — An emission control system malfunction has been detected. Check the fuel-filler cap if the LOOSE FUEL CAP warning appears in the vehicle information display, and the fuel- filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. light should turn off after a few The driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. ● Malfunction Indicator Light blinking — An engine misfire has been detected which may damage the emission control system. To re- duce or avoid emission control system dam- age: – do not drive at speeds above 45 MPH (72 km/h). – avoid hard acceleration or deceleration. – avoid steep uphill grades. – if possible, reduce the amount of cargo being hauled or towed. Instruments and controls 2-19 The Malfunction Indicator Light may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. CAUTION Continued vehicle operation without hav- ing the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system. Security indicator light This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational. For additional tems” later in this section. information, see “Security sys- Slip indicator light This indicator will blink when the VDC system or the traction control system is operating, thus alerting that the vehicle is nearing its traction limits. The road surface may be slippery. 2-20 Instruments and controls Turn signal/hazard indicator lights The appropriate light flashes when the turn signal switch is activated. Both lights flash when the hazard switch is turned on. Vehicle Dynamic Control (VDC) OFF indicator light This indicator light comes on when the Vehicle Dynamic Control off switch is pushed to OFF, the transfer case is in the 4LO position ( model), or when the Vehicle Dynamic Control system is not functioning properly. This indicates the Vehicle Dynamic Control system is not oper- ating. Push the Vehicle Dynamic Control OFF switch again or restart the engine and the system will operate normally. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” sec- tion of this manual. The Vehicle Dynamic Control OFF light also comes on when you place the ignition switch in the ON position. The light will turn off after about 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indica- tor light while you are driving, have the Vehicle Dynamic Control system checked by a NISSAN dealer. While the Vehicle Dynamic Control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal. AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime A chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch placed in the OFF posi- tion, a chime sounds when the driver’s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leav- ing the vehicle. VEHICLE INFORMATION DISPLAY The icons at the bottom of the display screen show the options available: ENTER — Press the INFO button to select a highlighted option. NEXT — Rotate the INFO button to high- light an option. WIC1248 The vehicle information display 䊊1 is located to the left of the speedometer. It displays such items as: ● automatic transmission position indicator ● cruise control system information ● Intelligent Key operation information (if so equipped) ● some indicators and warnings ● other information For details about the Intelligent Key, see “NISSAN Intelligent Key™” in the “Pre-driving checks and adjustments” section. WIC1249 HOW TO USE THE VEHICLE INFORMATION DISPLAY Press the vehicle information display INFO but- ton 䊊1 located on the instrument panel to toggle through the following modes. MPG → Range → Warning Rotate the INFO button 䊊2 to highlight the de- sired menu option within the selected mode. Press the INFO button 䊊1 to enter the high- lighted menu. Instruments and controls 2-21 WIC1166 Warning mode The warning mode can be selected to view any warnings that may be present. Once the screen is selected you have the option of skipping the warning or viewing it in detail. Warnings can be present for issues such as an open door or low fuel. For more information about potential warnings see “Vehicle information dis- play warnings and indicators” later in this section. 2-22 Instruments and controls Vehicle information display warnings and indicators 1. Door and liftgate open warning 2. Lock warning (NISSAN Intelligent Key™ model) 3. Low fuel warning 4. Low windshield-washer fluid warning 5. No key warning (NISSAN Intelligent Key™ model) 6. Parking brake warning LIC2005 7. Shift P warning (NISSAN Intelligent Key™ model) 8. Cruise main switch indicator 9. Cruise set switch indicator Instruments and controls 2-23 10. NISSAN Intelligent Key™ battery discharge indicator (NISSAN Intelligent Key™ model) 11. Transfer 4LO position indicator ( model) 12. 4WD shift indicator ( model) 13. Shift selector position indicator 14. Loose fuel cap warning 15. Check tire pressure waning Door and liftgate open warning This warning illuminates when a door, the liftgate or the liftgate glass has been opened when the ignition switch is placed in the ON position. Lock warning (NISSAN Intelligent Key™ model) This warning illuminates and a chime sounds if the ignition switch has been in the ACC or ON position and then placed in the OFF position. Place the ignition switch in the LOCK position and the warning and chime will turn off. Refer to “Shift P warning” in this section for additional information. Low fuel warning This warning illuminates when the fuel level in the fuel tank is getting low. Refuel as soon as it is 2-24 Instruments and controls convenient, preferably before the fuel gauge reaches E (Empty). There will be a small re- serve of fuel in the tank when the fuel gauge needle reaches E (Empty). Low windshield-washer fluid warning This warning illuminates when the windshield- washer fluid is at a low level. Add windshield- washer fluid as necessary. See “Windshield- washer fluid” in the “Maintenance and do-it- yourself” section of this manual. No key warning (NISSAN Intelligent Key™ model) This warning illuminates following two condi- tions: 1. When the ignition switch is pushed and the Intelligent Key cannot be recognized by the system. If this warning illuminates, you can- not start the engine. Check for the following causes and perform the assigned remedies: – The battery of the Intelligent Key carried with you is discharged completely. Re- place the battery with a new one. – The Intelligent Key carried with you is not registered to the system. Use the regis- tered Intelligent Key. – You do not have an Intelligent Key with you. Carry an Intelligent Key with you. 2. When the door is closed with the Intelligent Key left outside the vehicle and the ignition switch is in the ACC or ON position. A chime will also sound. Parking brake warning This warning illuminates when the parking brake is set and the vehicle is driven. SHIFT P warning (NISSAN Intelligent Key™ model) This warning illuminates when the ignition switch is in the ACC or OFF position and the shift selector is in any position other than (Park) posi- tion. Also, a chime sounds when the ignition switch is in the OFF position. If this warning illuminates, move the shift selector to the P (Park) position or start the engine. If the shift selector is moved to the P (Park) position, the lock warning will appear. Refer to “Lock warning” in this section. For additional information about Intelligent Key, see “NISSAN Intelligent Key™” in the “Pre-driving checks and adjustments” section. Cruise main switch indicator This indicator illuminates when the cruise control main switch is pushed. The indicator turns off when the main switch is pushed again. When the cruise main switch indicator the cruise control system is operational. Cruise set switch indicator light illuminates, The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning prop- erly. Have the system checked by a NISSAN dealer. NISSAN Intelligent Key™ battery dis- charge indicator (NISSAN Intelligent Key™ model) This indicator illuminates when the Intelligent Key battery is running out of power. If this indicator illuminates, replace the battery with a new one. See “Battery replacement” in the “Maintenance and do-it-yourself” section. Transfer 4LO position indicator ( model) This indicator illuminates when the 4WD shift switch is set in the 4LO position with the ignition switch placed in the ON position. If the 4WD shift switch is set in the 4LO position and the indicator blinks, stop the vehicle, drive slowly forward and the indicator will turn on. When you shift between 4H and 4LO, stop the vehicle, move the shift selector to the N (Neutral) position, then depress and turn the 4WD shift switch to 4LO or 4H. The transfer case may be damaged if you shift the switch while driving. You cannot move the transfer 4WD shift switch between 4H and 4LO unless you have first stopped the vehicle and moved the shift selector to N (Neutral). Make sure the transfer 4LO posi- tion indicator illuminates when you shift the 4WD shift switch to 4LO. The indicator may blink while shifting from one drive mode to the other. 4WD shift indicator ( model) While the engine is running, the 4WD shift indi- cator will illuminate the position selected by the 4WD shift switch. The 4WD shift indicator may blink while shifting from one drive mode to the other. Automatic transmission position indicator When the ignition switch is placed in the ON position, this indicator shows the shift selector position. See “Driving the vehicle” in the “Starting and driving” section of this manual. Loose fuel cap warning This warning appears when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. See “Fuel-filler cap” in the “Pre-driving checks and adjustments” section. Check tire pressure warning This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected. If this warning appears, stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. See “Low tire pressure warning light” earlier in this section and “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section. Instruments and controls 2-25 SECURITY SYSTEMS LIC0559 Your vehicle has two types of security systems: ● Vehicle security system ● NISSAN Vehicle Immobilizer System VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs. The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Al- ways secure your vehicle even if parking for a 2-26 Instruments and controls brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible. Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. How to arm the vehicle security system 1. Close all windows. (The system can be armed even if the windows are open.) 2. Place the ignition switch in the LOCK posi- tion and remove the key. 3. Close all doors. Lock all doors. The doors can be locked with: ● the power door lock switch (if the door is opened, locked and then closed). ● the key — master or mechanical (NISSAN Intelligent Key™ models). ● any request switch (NISSAN Intelligent Key™ models). ● the keyfob or NISSAN Intelligent Key™. Keyfob and NISSAN Intelligent Key™ opera- tion: ● Push the button. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. ● When the button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a re- minder that the doors are already locked. The horn may or may not beep. Refer to “Silencing the horn beep feature” in the Pre- driving checks and adjustments” section or “Comfort & Convenience settings” in the “Monitor, climate, audio, phone and voice recognition systems” section. 4. Confirm that the indicator light comes on. The light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the ve- hicle security system automatically shifts light begins into the armed phase. The to flash once every 3 seconds. If, during the 30-second pre-arm time period, the driver’s door is unlocked by the key, a request switch, the keyfob or Intelligent Key, or if the ignition switch is placed in the ACC or ON position, the system will not arm. ● If the key is turned slowly when locking the driver’s door, the system may not arm. Furthermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again. ● Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition switch placed in the OFF position. Vehicle security system activation The vehicle security system will give the following alarm: ● The headlights blink and the horn sounds intermittently. ● The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver’s door with the key, a request button on switch or by pressing the the keyfob or Intelligent Key. The alarm is activated by: ● opening a door without using the key, a request switch, keyfob or Intelligent Key (even if the door is unlocked by using the inside lock knob or the power door lock switch). How to stop an activated alarm The alarm stops only by unlocking the driver’s door button on the with the key, pressing the keyfob or Intelligent Key, or by unlocking all doors with any request switch (Intelligent Key models). NISSAN VEHICLE IMMOBILIZER SYSTEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following procedures: 1. Leave the ignition switch placed in the ON position for approximately 5 seconds. 2. Place the ignition switch in the OFF or LOCK position and wait approximately 10 seconds. 3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key. If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY — IMMOBILIZER, ANT ASSY — IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RE- SPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPER- ATE THE EQUIPMENT. Instruments and controls 2-27 WINDSHIELD WIPER AND WASHER SWITCH LIC0474 LIC0965 Security indicator light The security indicator light blinks whenever the ignition switch is placed in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition switch is placed in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser- vice as soon as possible. Please bring all registered keys that you have when visiting your NISSAN dealer for service. 2-28 Instruments and controls SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position. Push the lever down to operate the wiper at the following speed: 䊊1 Intermittent (INT) — intermittent operation can be adjusted by turning the knob toward 䊊A (Slower) or 䊊B (Faster). Also, the inter- mittent operation speed varies in accor- dance with the vehicle speed. (For example, when the vehicle speed is high, the intermit- tent operation speed will be faster.) NOTE: You can turn on or turn off the driving speed dependent intermittent wiper func- tion. Refer to “Comfort & convenience set- tings” in the “Monitor, climate, audio, phone and voice recognition systems” sec- tion later in this manual. 䊊2 Low (LO) — continuous low speed operation 䊊3 High (HI) — continuous high speed opera- tion Push the lever up 䊊4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you 䊊5 to operate the washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield. REAR WINDOW WIPER AND WASHER SWITCH CAUTION ● Do not operate the washer continu- ously for more than 30 seconds. ● Do not operate the washer if the windshield-washer reservoir is empty. ● Do not fill the windshield-washer reser- voir with washer fluid concentrates at full strength. So methyl alcohol based windshield-washer fluid concentrates may permanently stain the grille if spilled with filling the windshield- washer fluid reservoir. ● Pre-mix windshield-washer fluid con- centrates with water to the manufactur- er’s recommended levels before pour- ing the fluid into the windshield-washer reservoir. Do not use the windshield- washer reservoir to mix the windshield- washer fluid concentrate and water. LIC0966 The rear window wiper and washer operate when the ignition switch is placed in the ON position. Turn the switch clockwise from the OFF position to operate the wiper. 䊊1 Intermittent (INT) – intermittent operation (not adjustable) 䊊2 ON – continuous low speed operation Push the switch forward 䊊3 to operate the washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solu- tion may freeze on the window and ob- scure your vision. Warm the rear window with the defroster before you wash the rear window. CAUTION ● Do not operate the washer continu- ously for more than 30 seconds. ● Do not operate the washer if fluid reservoir the is windshield-washer empty. ● Do not fill the windshield-washer fluid reservoir with washer fluid concen- trates at full strength. Some methyl al- cohol based washer fluid concentrates may permanently stain the grille if spilled while filling the windshield- washer fluid reservoir. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the windshield-washer fluid reser- voir. Do not use the windshield-washer fluid reservoir to mix the washer fluid concentrate and water. Instruments and controls 2-29 REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH LIC1173 To defrost the rear window glass and outside mirrors: Start the engine and push the rear window de- froster switch. The rear window defroster indica- tor light on the display screen comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes. CAUTION When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster. 2-30 Instruments and controls WIC1250 WIC1186 Type A HEADLIGHT CONTROL SWITCH Lighting 䊊1 When turning the switch to the posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊2 When turning the switch to the posi- tion, the headlights come on and all the other lights remain on. Type B CAUTION Use the headlights with the engine run- ning to avoid discharging the vehicle battery. NOTE: Autolight activation sensitivity and the time delay for autolight shutoff can be ad- justed. See “Comfort & convenience set- tings” in the “Monitor, climate, audio, phone and voice recognition systemsⴖsec- tion later in this manual. To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi- tion 䊊1 . 2. Turn the ignition switch to ON. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain ON for 5 minutes. If another door is opened during the 5 minutes, then the 5 minute timer is reset. To turn the autolight system off, turn the switch to the OFF, position. , or Instruments and controls 2-31 Type C SIC3019 WIC1251 Autolight system The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: ● Turn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark. ● Turn off all the lights when it is light. ● Keep all the lights on for up to 180 seconds after you place the ignition switch in the OFF position and all doors are closed. After the headlights automatically turn off with the position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position position. and then turned to the or or LIC0836 Be sure you do not put anything on top of the autolight sensor 䊊1 located in the top side of the instrument panel. The autolight sensor controls the autolight; if it is cov- ered, the autolight sensor reacts as if it is dark out and the headlights will illuminate. If this occurs while parked with the engine off and the ignition switch placed in the ON position, your vehicle’s battery could be- come discharged. 2-32 Instruments and controls WIC1252 Headlight beam select 䊊1 To select the high beam function, push the lever forward. The high beam lights come on and the light illuminates. 䊊2 Pull the lever back to select the low beam. 䊊3 Pulling and releasing the lever flashes the headlight high beams on and off. Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the or 5 minutes. position, the headlights will turn off after CAUTION Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the position. Turn the OFF position or in the position for full headlight switch to the illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is placed in the OFF position. WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others. WIC1506 WIC1253 INSTRUMENT BRIGHTNESS CONTROL The instrument brightness control operates when the in or AUTO position (with auto- the lights activated). Turn the control to adjust the brightness of instru- ment panel lights when driving at night. headlight control switch is TURN SIGNAL SWITCH Turn signal 䊊1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically. Lane change signal 䊊2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch. Instruments and controls 2-33 HAZARD WARNING FLASHER SWITCH The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road. ● Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic. ● Turn signals do not work when the haz- ard warning flasher lights are on. position. WIC1254 FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch position, then turn the fog light to the switch to the To turn the fog lights on with the headlight switch in the AUTO position, the headlights must be on, then turn the fog light switch to the To turn the fog lights off, turn the fog light switch to the OFF position. The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected. 2-34 Instruments and controls position. HORN HEATED SEAT (if so equipped) LIC0604 To sound the horn, push the center pad area of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury. WIC1441 The front seats are warmed by built-in heaters. 1. Start the engine. 2. Push the LO or HI position of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on. 3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off. CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. ● Any liquid spilled on the heated seat should be removed immediately with a dry cloth. ● When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials. ● If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer. ● The battery could run down if the seat heater is operated while the engine is not running. Instruments and controls 2-35 HEATED STEERING WHEEL (if so equipped) VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH NOTE: The heated steering wheel switch is equipped with a 30 minute timer. After the switch has been activate for 30 minutes, the system will automatically turn off.If the surface temperature of the steering wheel is above 68°F (20°C) when the switch is turned on, the system will not heat the steering wheel. This is not a malfunction. LIC0421 The heated steering wheel system is designed to operate only when the surface temperature of the steering wheel is below approximately 68°F (20°C). Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light will come on. If the surface temperature of the steering wheel is below 68°F (20°C), the system will heat the steering wheel to approximately 86°F (30°C), then turn off automatically. Push the switch again to turn the heated steering wheel off manually. The indicator light will go off. 2-36 Instruments and controls WIC0534 The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driv- ing conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn on the system. See “Vehicle Dy- namic Control (VDC) system” in the “Starting and driving” section. indicator will come on. REAR SONAR SYSTEM OFF SWITCH (if so equipped) FRONT AND REAR SONAR SYSTEM OFF SWITCH (if so equipped) The rear sonar system can be disabled by push- ing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. The system will automatically reset the next time the ignition switch is placed in the ON position. See “Rear sonar system” in the “Starting and driving” section. LIC0471 WARNING The rear sonar system is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly. The rear sonar system is active when the ignition switch is placed in the ON position and the shift selector is in R (Reverse). When sensors detect obstacles within 5.9 ft (1.8 m) of the rear bumper, a beeping tone is emitted. LIC1182 WARNING ● The front sonar system is a convenience but it is not a substitute for proper driving. ● The rear sonar system is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly. Instruments and controls 2-37 The front sonar system: ● is active when the ignition is in the ON position and the shift selector is in a forward gear position. ● a beeping tone is emitted when the sensors detect obstacles within 3 ft (1.0 m) of the front bumper. The rear sonar system: ● is active when the ignition is in the ON position and the shift selector is in R (Re- verse). ● a beeping tone is emitted when the sensors detect obstacles within 5.9 ft (1.8 m) of the rear bumper. The front and rear sonar system can be disabled by pushing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. Push the switch again to enable the system. The indicator light will go off. The system will automatically reset the next time the ignition switch is placed in the ON position. See “Front sonar system” in the “Starting and driving” section. 2-38 Instruments and controls TOW MODE SWITCH For additional information, refer to “Tow mode” in the “Technical and consumer information” sec- tion later in this manual. LIC0594 Tow mode should be used when pulling a heavy trailer or hauling a heavy load. Driving the vehicle in the tow mode with no trailer/load or light trailer/light load will not cause any damage. How- ever, fuel economy may be reduced, and the transmission/engine driving characteristics may feel unusual. Press the tow mode switch to activate tow mode. The indicator light on the tow mode switch illumi- nates when tow mode is selected. Press the tow mode switch again to turn tow mode OFF. Tow mode is automatically canceled when the ignition switch is placed in the OFF position. POWER OUTLET Front row 2nd row Luggage area LIC1193 LIC0550 LIC0551 The power outlets are for powering electrical accessories such as cellular telephones. The power outlets located on the driver’s side of the instrument panel and in the luggage area are powered directly by the vehicle’s battery. The power outlets located on the passenger’s side of the instrument panel and in the 2nd row are powered only when the ignition switch is in the ACC or ON position. Open the cap to use a power outlet. Instruments and controls 2-39 STORAGE CONSOLE BOX Center stack storage INSTRUMENT PANEL STORAGE TRAYS LIC1183 WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop. CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information. ● Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. ● Use power outlets with the engine run- ning to avoid discharging the vehicle battery. ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. ● When not in use, be sure to close the cap. Do not allow water or any other liquids to contact the outlet. 2-40 Instruments and controls Console box storage trays LIC1369 LIC1370 LIC1371 Console box storage Pull up on the lever 䊊1 to open the console box lid 䊊2 . Console box lock Use the master key to lock 䊊1 or unlock 䊊2 the console box. Instruments and controls 2-41 CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC1176 WIC0673 GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking 䊊1 or unlocking 䊊2 the glove box. SUNGLASSES HOLDER To open the sunglasses holder, push and release. Only store one pair of sunglasses in the holder. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. WARNING Keep the sunglasses holder closed while driving to prevent an accident. 2-42 Instruments and controls MAP POCKETS LIC1195 LIC0575 LIC0568 SEATBACK POCKET The seatback pocket is located on the back of the driver seat. The pocket can be used to store maps. Small bin OVERHEAD CONSOLE Instruments and controls 2-43 LIC0569 LIC0570 WIC1507 Medium bin (if so equipped) Large bin Storage bins WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Push the button to open a storage bin. Push the lid up to close. 2-44 Instruments and controls CUP HOLDERS Front CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. Adjustable 2nd row (rear of front console) LIC1373 LIC0554 LIC0555 2nd row center console (if so equipped) Position the arm on the adjustable cup holder so that the cup is held securely. To open the 2nd row cup holders (rear of the front console), lower the lid. To close, raise the lid. Instruments and controls 2-45 LIC0556 LIC0557 WIC1197 2nd row bench (if so equipped) 3rd row Bottle holder CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid containers. 2-46 Instruments and controls To reinstall the 2nd row center console box: 1. Slide the console box over the base toward the rear of the vehicle. 2. Push down to lock the console box in place. 3. Replace the cup holder tray. LIC0576 2ND ROW CENTER CONSOLE (if so equipped) Pull up on the lever to open the console box lid. LIC0577 Removing the 2nd row center console box To remove the 2nd row center console box: 䊊1 䊊2 Pull up on the handle to tilt the console box Lift out the cup holder tray. up. 䊊3 Move the console box toward the front of the vehicle and lift it out. Instruments and controls 2-47 LIC0571 LIC2014 CARGO AREA STORAGE BIN To open the cargo area storage bin, pull down on the tab and pull the lid off. CAUTION Placing additional items in the area speci- fied for the jack may dent body panel or damage power back door assembly (if so equipped). LIC0572 To access the floor storage area, push down 䊊1 to raise the handle, then pull up on the handle 䊊2 to lift the luggage board. LUGGAGE HOOKS The luggage hooks can be used to secure cargo with ropes or other types of straps. 2-48 Instruments and controls WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury. ● Use suitable ropes and hooks to secure cargo. ● Never allow anyone to ride in the lug- gage area. It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. ● The child restraint top tether strap may be damaged by contact with items in the cargo area. Secure any items in the cargo area. Your child could be seri- ously injured or killed in a collision if the top tether strap is damaged. ● Be sure everyone in your vehicle is in a seat and using a seat belt properly. LTI0089 LTI0090 Side finisher When hooking on ropes, do not apply a load of more than 55 lb (245 N) to a single 䊊A hook or 44 lb (196 N) to a single 䊊B hook. Floor hooks Do not apply a load of more than 110 lb (490 N) to a single hook. Instruments and controls 2-49 WARNING ● Drive extra carefully when the vehicle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack. ● Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sudden or abnor- mal handling maneuvers. ● Roof rack load should be evenly distributed. ● Do not exceed maximum roof rack load weight capacity. ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury. LIC1177 CAUTION Use care when placing or removing items from the roof rack. If you cannot comfort- ably lift the items onto the roof rack from the ground, use a ladder or stool. ROOF RACK 2-50 Instruments and controls Always distribute the luggage evenly on the roof rack. Do not load more than 200 lbs (91 kg) on entire roof rack. Be sure load is evenly distributed across both crossbars. Be careful that your ve- hicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, refer to “Vehicle loading information” in the “Technical and con- sumer information” section later in this manual. WINDOWS POWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents. The power windows operate when the ignition switch is placed in the ON position, or for about 45 seconds after the ignition switch is placed in the OFF position. If the driver’s or passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled. Instruments and controls 2-51 LIC1200 The crossbars can be adjusted forward and backward. Loosen the thumbwheel 䊊1 and ad- just the crossbar to the desired position. Tighten the thumbwheel. Place your luggage on the bars and secure the luggage with rope to the utility loops 䊊2 . Do not place luggage on the side rails or tie rope directly to the side rails. Always be sure the thumbwheels are fully tightened to keep the crossbar in place. Do not use utility loops for any purpose other than securing luggage. Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch. WIC1237 Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window. To open the window, push the switch and hold it down 䊊1 . To close the window, pull the switch up 䊊2 . LIC1181 1. Window lock button 2. 3. 4. 5. 6. Power door lock switch Front passenger side automatic switch Right rear passenger window switch Left rear passenger window switch Driver side automatic switch 2-52 Instruments and controls WIC1255 LIC0410 Rear power window switch The rear power window switches open or close only the corresponding windows. To open the window, push the switch and hold it down 䊊1 . To close the window, pull the switch up 䊊2 . Locking passengers’ windows When the window lock button is depressed, only the driver’s side window can be opened or closed. Push it again to cancel the window lock function. Automatic operation To fully open a window equipped with automatic operation, press the window switch down (only driver’s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening. To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held. To stop the window, press the switch down while the window is closing. Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs. WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window. the dealer If the vehicle’s battery is disconnected, replaced, or jump started, the power window auto-reverse function may not operate properly. If this occurs, please contact to re-initialize the power window auto-reverse system. If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately low- ered. Instruments and controls 2-53 The power vent windows operate when the igni- tion switch is placed in the ON position, or for about 45 seconds after the ignition switch is placed in the OFF position. If the driver’s or passenger’s door is opened during this 45 sec- ond period, power to the vent windows is can- celled. LIC1417 POWER VENT WINDOWS (if so equipped) Use the vent window switch located on the driv- er’s side of the instrument panel to open and close the power vent windows. The windows cannot be operated separately. To open the power vent windows press and hold the switch. To close the windows pull up and hold the switch. 2-54 Instruments and controls LIC0524 MANUAL VENT WINDOWS (if so equipped) To open a manual vent window, pull the latch handle toward you until it releases. To lock the window in the open position, push the latch handle rearward until it locks. To close a manual vent window, pull the latch handle toward you and push the rear portion of the latch toward the rear of the vehicle until it locks. MOONROOF (if so equipped) WIC0812 AUTOMATIC MOONROOF The moonroof will only operate when the ignition switch is placed in the ON position. The auto- matic moonroof is operational for about 45 sec- onds, even if the ignition switch is placed in the ACC or OFF position. If the driver’s door or the front passenger’s door is opened during this period of about 45 seconds, power to the moon- roof is canceled. Sliding the moonroof To fully open the moonroof, push the switch to- ward the open position 䊊3 . To fully close the moonroof, push the switch toward the close position 䊊4 . To open or close the moonroof part way, push the switch in any direction 䊊5 while the moonroof is sliding open or closed to stop it in the desired position. Tilting the moonroof To tilt the moonroof up, push the tilt switch to- ward the up position 䊊1 . When the moonroof is open, it will automatically close and then tilt up. To tilt the moonroof down, push the tilt switch toward the down position 䊊2 . Restarting the moonroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electri- cal supply interrupted and/or some abnormality detected. Use the following reset procedure to return moonroof operation to normal. 1. If the moonroof lid is open, push the tilting switch repeatedly toward the down position 䊊2 to fully close the lid. 2. Push and hold the tilting switch for more than 2 seconds toward the down position 䊊2 to reestablish the lid’s home position. The moonroof should now operate normally. Auto-reverse function (when closing or tilting down the moonroof) The auto-reverse function can be activated when the moonroof is closed or tilted down by auto- matic operation when the ignition switch is placed in the ON position or for about 45 sec- onds after the ignition switch is placed in the OFF position. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs. WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof. When closing: If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward. Instruments and controls 2-55 When tilting down: If the control unit detects something caught in the moonroof as it tilts down, the moonroof will im- mediately tilt up. If the auto-reverse function malfunctions and re- peats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof. WARNING ● In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints. ● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing. CAUTION ● Remove water drops, snow, ice or sand from the moonroof before opening. ● Do not place heavy objects on the moonroof or surrounding area. 2-56 Instruments and controls INTERIOR LIGHT Sunshade Open and close the sunshade by sliding it for- ward or backward. If the moonroof does not close Have your NISSAN dealer check and repair the moonroof. LIC0585 The interior light has a three-position switch and operates regardless of ignition switch position. When the switch is in the ON position 䊊1 , the interior lights illuminate, regardless of door posi- tion. The lights will go off after about 15 minutes unless the ignition switch is in the ON position. When the switch is in the DOOR position 䊊2 , the interior lights and puddle lights (if so equipped) will stay on for about 30 seconds when: ● The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position. NOTE: The footwell lights (if so equipped) and door step lights illuminate when the driver and passenger doors are open regardless of the interior light switch position. These lights will turn off automatically after about 15 minutes while doors are open to prevent the battery from becoming discharged. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. ● The driver’s door is opened and then closed while the key is removed from the ignition switch. ● The key is removed from the ignition switch while all doors are closed. The lights will turn off while the 30 second timer is activated when: ● The driver’s door is locked by the keyfob, a key, or the power door lock switch. ● The ignition switch is placed in the ON po- sition. When the switch is in the OFF position 䊊3 , the interior lights do not illuminate, regardless of door position. The puddle lights (if so equipped) come on when any front or rear passenger door is opened. The lights will turn off automatically after 15 min- utes while doors are open to prevent the battery from becoming discharged. LIC0587 CONSOLE LIGHT The console light 䊊1 will turn on whenever the parking lights or headlights are illuminated. The console light brightness can be adjusted with the illumination brightness control. Instruments and controls 2-57 PERSONAL LIGHTS MAP LIGHTS CARGO LIGHT LIC0588 The personal lights on the overhead console can be swiveled 360 degrees. To turn on the light, press the button. Press the button again to turn off the light. LIC0586 To turn the map lights on, press the switches. To turn them off, press the switches again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. LIC0590 The cargo light on the overhead trim has a three- position switch. To operate, push the switch to the desired position. ON: The light is illuminated. Normal (center) position: The light illuminates when the lift gate or glass hatch is opened. The light turns off when the lift gate or glass hatch is closed. OFF: The light does not illuminate regardless of lift gate position or lock status. 2-58 Instruments and controls HOMELINK姞 UNIVERSAL TRANSCEIVER (if so equipped) The HomeLink姞 Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink姞 Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems. ● Is powered by your vehicle’s battery. No separate batteries are required. If the vehi- cle’s battery is discharged or is discon- nected, HomeLink姞 will retain all program- ming. Once the HomeLink姞 Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink姞 Universal Transceiver buttons should be erased for security purposes. For additional information, refer to “Program- ming HomeLink姞” later in this section. the vehicle, WARNING ● Do not use the HomeLink姞 Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death. ● During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming. ● Your vehicle’s engine should be turned off while programming the HomeLink姞 Universal Transceiver. WIC0986 PROGRAMMING HOMELINK姞 1. To begin, press and hold the two outer HomeLink姞 buttons (to clear the memory) until the indicator light 䊊1 blinks (after 20 seconds). Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink姞 surface. Instruments and controls 2-59 5. grammed device, press and hold the pro- grammed HomeLink姞 button — releasing when the device begins to activate. If the indicator light on the HomeLink姞 blinks rapidly for 2 seconds and then turns solid, HomeLink姞 has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train the HomeLink姞 to complete the programming which may require a ladder and another per- son for convenience. 6. Press and release the “smart” or “learn” pro- gram button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button. NOTE: Once you have pressed and released the program button on the garage door open- er’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step. 7. Within 30 seconds of pressing and releas- ing the garage door opener’s program but- WIC0987 3. Using both hands, simultaneously press and hold both the HomeLink姞 button you want to program and the hand-held transmitter but- ton. DO NOT release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLink姞 flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro- 2-60 Instruments and controls ton, quickly and firmly press and release the HomeLink姞 button you’ve just programmed. Press and release the HomeLink姞 button up to 3 times to complete the training. 8. Your HomeLink姞 button should now be pro- grammed. (To program the remaining HomeLink姞 buttons for additional door or gate openers, follow steps 2-4 only.) all previously NOTE: Do not repeat step 1 unless you want to “clear” programmed HomeLink姞 buttons. If you have any questions or are having difficulty programming your HomeLink姞 buttons, refer to the HomeLink姞 web site at: www.homelink.com or call 1-800-355-3515. PROGRAMMING HOMELINK姞 FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLink姞, continue to press and hold the HomeLink姞 button (see steps 2 - 4under “Pro- gramming HomeLink姞”) while you press and re- press (“cycle”) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming). NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the “cycling” process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINK姞 UNIVERSAL TRANSCEIVER The HomeLink姞 Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLink姞 Universal Transceiver button. The amber indicator light will illuminate while the signal is being transmitted. PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLink姞 does not quickly learn the hand- held transmitter information: ● replace the hand-held transmitter batteries with new batteries. ● position the hand-held transmitter with its from the facing away battery HomeLink姞 surface. area ● press and hold both the HomeLink姞 and hand-held transmitter buttons without inter- ruption. ● position the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLink姞 surface. Hold the transmitter in that position for up to 15 seconds. If HomeLink姞 is not programmed within that time, try holding the transmitter in another position – keeping the indicator light in view at all times. If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). REPROGRAMMING A SINGLE HOMELINK姞 BUTTON To reprogram a HomeLink姞 Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLink姞 but- ton. Do not release the button until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3inches (26 - 76 mm) away from the HomeLink姞 surface. 3. Press and hold the hand-held transmitter button. 4. The HomeLink姞 indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons. The HomeLink姞 Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink姞 button that was just programmed. This procedure will not affect any other programmed HomeLink姞 buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink姞. Consult the Owner’s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLink姞 Univer- sal Transceiver with your new transmitter information. Instruments and controls 2-61 FCC Notice: This device complies with FCC rules part 15 and RSS-210 of Industry Canada. Opera- tion is subject to the following two condi- tions: (1) This device may not cause harmful in- terference and (2) This device must accept any interference that may be received, in- cluding interference that may cause undes- ired operation. This transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user’s authority to op- erate the equipment. DOC: ISTC 1763K1313 FCC I.D. CV2V67690 2-62 Instruments and controls 3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN Intelligent Key™ (if so equipped) . . . . . . . . . 3-2 NISSAN Vehicle Immobilizer System keys . . . . . . . . . 3-4 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-6 Locking with power door lock switch . . . . . . . . . . . . . 3-6 Automatic door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Child safety rear door lock. . . . . . . . . . . . . . . . . . . . . . . 3-7 Remote keyless entry system (if so equipped). . . . . . . . . 3-7 How to use remote keyless entry system . . . . . . . . . . 3-8 NISSAN Intelligent Key™ (if so equipped) . . . . . . . . . . . 3-12 Operating range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Door locks/unlocks precaution . . . . . . . . . . . . . . . . . . 3-14 NISSAN Intelligent Key™ Operation. . . . . . . . . . . . . . 3-15 How to use the remote keyless entry function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21 Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 Operating the manual lift gate (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Operating the power lift gate (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Cancel switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26 Lift gate release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27 Glass hatch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 Pedal position adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 3-31 Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31 Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Rearview mirror (if so equipped). . . . . . . . . . . . . . . . . 3-32 Automatic anti-glare rearview mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33 Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35 Automatic drive positioner (if so equipped) . . . . . . . . . . 3-37 Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-37 Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38 System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39 KEYS A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. 1. WPD0128 Two master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip Key number plate Transponder chip 2. 3. 4. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. 3-2 Pre-driving checks and adjustments WPD0427 Two Intelligent Keys 1. 2. Mechanical keys (inside Intelligent Keys) Key number plate 3. NISSAN INTELLIGENT KEY™ (if so equipped) Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intel- ligent Key components and NISSAN Vehicle Im- mobilizer System components. ● Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, im- mediately wipe until it is completely dry. ● Do not place the Intelligent Key for an extended period in an area where tem- peratures exceed 140°F (60°C). ● Do not attach the Intelligent Key with a key holder that contains a magnet. ● Do not place the Intelligent Key near equipment that produces a magnetic field, such as a TV, audio equipment and personal computers. If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelligent Key from the vehicle.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2011 Nissan Armada Owners Manual