Download PDF Manual

airborne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the (cid:147)War- ranty Information and Maintenance Booklet(cid:148) for change intervals. If replacement is required, see your NISSAN dealer.


WINDSHIELD WIPER BLADES


CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.


CAUTION


Worn windshield wiper blades can dam- age the windshield and impair driver vision.


Maintenance and do-it-yourself 8-19


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


CAUTION


c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.


c Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.


WDI0594


REPLACING Replace the wiper blades if they are worn.


1. Lift the wiper arm away from the windshield. s2 Push the release tab, then move the wiper


blade down the wiper arm to remove.


s3 Remove the wiper blade. 4.


Insert the new wiper blade onto the wiper arm until it clicks into place.


5. Rotate wiper blade so the dimple is in the


groove.


8-20 Maintenance and do-it-yourself


WDI0570
If you wax the surface of the hood, be careful not to let wax get into the washer nozzle sA . This may cause clogging or improper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin sB .


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


BRAKES


FUSES


If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Your vehicle is equipped with self-adjusting brakes.


The front and rear disc-type brakes self-adjust every time the brake pedal is applied.


WARNING


See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal.


BRAKE PAD WEAR INDICATORS The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard.


Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system.


Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148).


LDI0455
Two types of fuses are used. Type A is used in the fuse boxes in the engine compartment. Type B is used in the passenger compartment fuse box. Type A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type A fuses can be installed in the engine com- partment and passenger compartment fuse boxes.


Maintenance and do-it-yourself 8-21


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


3. Remove the fuse box cover by pushing the


tab and lifting the cover up.


4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.


LDI0457
If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. Type B fuses cannot be installed in the under- hood fuse boxes. Only use type A fuses in the underhood fuse boxes.


LDI0560


ENGINE COMPARTMENT


CAUTION


Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.


If any electrical equipment does not come on, check for an open fuse.


1. Be sure the ignition switch and the headlight


switch are OFF.


2. Open the engine hood.


8-22 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WDI0402


5.


6.


WDI0452
If the fuse is open sA , replace it with a new fuse sB . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.


Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.


PASSENGER COMPARTMENT


CAUTION


Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.


If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight


switch are OFF.


2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller.


Maintenance and do-it-yourself 8-23


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


BATTERY REPLACEMENT


CAUTION


Be careful not to allow children to swallow the battery and removed parts.


WDI0452


LDI0456


4.


Type A


If the fuse is open sA , replace it with an equivalent good fuse sB .


5. Push the fuse box cover to install. 6.


If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.


Type B


8-24 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


INTELLIGENT KEY BATTERY Replace the battery in the Intelligent Key as fol- lows: 1. Remove the mechanical key from the Intelli-


2.


gent Key. Insert a small screwdriver sA into the slit sB of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing.


3. Replace the battery with a new one.


Recommended battery: CR2032 or equiva- lent. c Do not touch the internal circuit and elec- tric terminals as doing so could cause a malfunction.


c Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity.


c Make sure that the + side faces the bot-


tom of the case.


WDI0567


WDI0568
4. Close the lid securely as illustrated sC sD . 5. Operate the buttons to check the operation.


See a NISSAN dealer if you need assistance for replacement. FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment.


This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.


Maintenance and do-it-yourself 8-25


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.


LIGHTS


HEADLIGHTS Replacing the xenon headlight bulb (if so equipped)


WARNING


cHIGH VOLTAGE


When xenon headlights are on, they pro- duce a high voltage. To prevent an electric shock, never attempt to modify or disas- semble. Always have your xenon head- lights replaced at a NISSAN dealer. For additional information, see (cid:147)Headlight and turn signal switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section. Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Be- cause the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.


CAUTION


c Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.


c Do not leave the headlight assembly open without a bulb installed for a long period of time. Dust, moisture, smoke, etc. entering the headlight body may affect bulb performance. Remove the bulb from the headlight assembly just before a replacement bulb is installed. c Only touch the base when handling the bulb. Never touch the glass envelope. Touching the glass could significantly affect bulb life and/or headlight performance.


c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.


c Use the same number and wattage as


originally installed: Low beam:


Wattage: 55
Bulb no.: H11*


High beam:


Wattage: 65
Bulb no.: H9*


*: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.


8-26 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


EXTERIOR AND INTERIOR LIGHTS


Item


Wattage (W)


Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer. FRONT PARK/TURN/SIDEMARKER LIGHT Bulb replacement requires the removal of the headlight assembly. If replacement is required, see your NISSAN dealer.


Headlight assembly *2
Low (Halogen) Low (Xenon) High Park Turn Sidemarker


Sedan Coupe


Front fog light (if so equipped) *2
Step light Rear combination light


Tail/Stop Turn


Backup (reversing)


Sedan Coupe


License plate light *2
High-mounted stop light *2


Inside (coupe) Inside (sedan) Spoiler (if so equipped)


55
35
65
27


55
(cid:151)


8/27
27


18
13


(cid:151) 18
(cid:151) 3.4
3.4


Bulb No.*1


H11
D2R H9
168


3457NAK


168
W5W H11
194


3157K 3156


921
912
W5W


LED 921
LED B5Y B5Y 158
658


Map light Interior light Trunk light Glove box light *2
*1 Always check with the Parts Department at a NISSAN dealer for the latest parts information. *2 See a NISSAN dealer for assistance.


Maintenance and do-it-yourself 8-27


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Interior light


Coupe 1. Mirror-mounted turn signal light 2. 3. Map light 4. Headlamp assembly 5. 6. 7. High-mount stoplight 8. 9. 10. Rear combination light


Fog light (if so equipped) Step light


Trunk light License plate light


8-28 Maintenance and do-it-yourself


WDI0626


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Rear map light Front map light Step light


Sedan 1. 2. 3. 4. Headlamp assembly 5. 6. High-mount stoplight (if so equipped) 7. 8.


Fog light (if so equipped)


Trunk light Spoiler mounted stoplight (if so equipped) Rear combination light


9. 10. License plate light


WDI0573


Maintenance and do-it-yourself 8-29


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Indicates bulb installation


Use a cloth s1 to protect the housing.


Step light


LDI0341


WDI0306


Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.


first remove the lens,


Indicates bulb removal


8-30 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Use a cloth s1 to protect the housing.


Map light


Use a cloth s1 to protect the housing.


Dome light


LDI0571


WDI0632


Maintenance and do-it-yourself 8-31


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Rear combination light To access the bulbs in the rear combination light: s1 Remove the fasteners. Carefully push back


the carpet.


s2 Remove the 2 nuts and pull out the rear


combination light.


s3 Rotate the bulb(s) counterclockwise and


pull out to remove: sA Turn signal light sB Sidemarker light sC Tail/stop light sD Backup light


8-32 Maintenance and do-it-yourself


WDI0635


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Trunk light


WDI0343


WHEELS AND TIRES


If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not de- tect a sudden drop in tire pressure (for example a flat tire while driving). For more details, refer to (cid:147)Low tire pres- sure warning light(cid:148) in the (cid:147)Instruments and controls(cid:148) section, (cid:147)Tire Pressure Monitor- ing System (TPMS)(cid:148) in the (cid:147)Starting and driving(cid:148) section, and (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section.


Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long dis- tance trips. The recommended tire pres- sure specifications are shown on the F.M.V.S.S./C.M.V.S.S. certification label or the Tire and Loading Information label under the (cid:147)Cold Tire Pressure(cid:148) heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.


The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds.


Maintenance and do-it-yourself 8-33


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.


WARNING


is


located on


c Improperly inflated tires can fail suddenly and cause an accident. c The Gross Vehicle Weight Rating (GVWR) the F.M.V.S.S./C.M.V.S.S. certifica- tion label. The vehicle weight ca- pacity is indicated on the Tire and Loading Information label (if so equipped). Do not load your ve- hicle beyond this capacity. Over- loading your vehicle may result in reduced tire life, unsafe operat- ing conditions due to premature tire failure, or unfavorable han- dling characteristics and could also lead to a serious accident. Loading beyond the specified ca- pacity may also result in failure of other vehicle components.


c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.


c Do not drive your vehicle over 85
MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire fail- ure, loss of control and possible injury.


c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


8-34 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


s6 Spare tire size (if so equipped).


Tire and loading information label s1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle.


s2 Vehicle load limit: See loading infor- mation in the (cid:147)Technical and con- sumer information(cid:148) section.


s3 Original tire size: The size of the tires originally installed on the vehicle at the factory.


LDI0549
s4 Cold tire pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicle(cid:146)s GVWR.


s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later


in this section.


Maintenance and do-it-yourself 8-35


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


4. Read the tire pressure on the gauge stem and compare to the specifica- tion shown on the Tire and Loading Information label.


5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.


6. 7. Check the pressure of all other tires,


including the spare.


LDI0393


Checking tire pressure 1. Remove the valve stem cap from the


tire.


2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.


3. Remove the gauge. 8-36 Maintenance and do-it-yourself


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Front Original Tire


Rear Original Tire


Spare Tire


Size


P215/60/R16
P215/55R17
P215/60R16
P215/55R17
T135/70R16
T135/90R16


Cold Tire Inflation Pres- sure 220 kPa, 32 PSI 230 kPa, 33 PSI 220 kPa, 32 PSI 230 kPa, 33 PSI


420 kPa, 60 PSI


Example


WDI0394


TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.


Maintenance and do-it-yourself 8-37


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating.


WDI0395


Example


s1 Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is de- signed for passenger vehicles (not all tires have this information).


2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge.


3. Two-digit number (65): This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width.


8-38 Maintenance and do-it-yourself


4. R: The 9R9 stands for radial. 5. Two-digit number (15): This number is the wheel or rim diameter in inches. 6. Two- or three-digit number (95): This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WDI0396


Example


s2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Depart- ment Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Num- ber.


2. Two-digit


code: Manufacturer(cid:146)s


identification mark


3. Two-digit code: Tire size


4. Three-digit code: Tire type code


(Optional)


5. Three-digit code: Date of Manufac-


ture


6. Four numbers represent the week and year the tire was built. For ex- ample, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.


s3 Tire ply composition and material


The number of layers or plies of rubber- coated fabric in the tire. Tire manufactur- ers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. s4 Maximum permissible inflation pres- sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible in- flation pressure. s5 Maximum load rating This number indicates the maximum load in kilograms and pounds that can be car- ried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory in- stalled tire. s6 Term of (cid:147)tubeless(cid:148) or (cid:147)tube type(cid:148) Indicates whether the tire requires an in- ner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). s7 The word (cid:147)radial(cid:148)


Maintenance and do-it-yourself 8-39


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


The word (cid:147)radial(cid:148) is shown if the tire has radial structure. s8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the out- ward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle.


8-40 Maintenance and do-it-yourself


TYPES OF TIRES


WARNING


c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.


c Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.


c For additional


information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.


All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ- ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas.


Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.


If you do not,


If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS


CAUTION


Only certain SAE class (cid:147)S(cid:148) tire chains can be used on this vehicle. Using the wrong Class (cid:147)S(cid:148) chains on this vehicle will cause damage to the vehicle. If you plan to use tire chains/cables, you should use a tire chain that meets the minimum clearances for your vehicle.


A tire chain that provides the specified amount of space will provide the necessary clearance be- tween the tire and the closest vehicle suspension or body component. The minimum clearances are determined using the factory-equipped tires. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action dam- age to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be ad- versely affected. Tire chains must be installed only on the front wheels and not on the rear wheels. Never install tire chains on a TEMPORARY USE ONLY spare tire. Do not use tire chains on dry roads. Driving with tire chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress.


Maintenance and do-it-yourself 8-41


LDI0574
Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use a tire chain that is designed to provide the specified space sA between the installed tire chain s1 and where the tire meets the rim s2 as shown on the chart.


Wheel size


Minimum space required


16 in


17 in


.7 in (17 mm)


.2 in (4 mm)


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WDI0258


CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emer- gency(cid:148) section of this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.


8-42 Maintenance and do-it-yourself


Wheel nut tightening torque:


83 ft-lb (112 N•m)


The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval.


WARNING


c After rotating the tires, check and


adjust the tire pressure.


c Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).


c Do not include the spare tire in


the tire rotation. c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


WDI0259


1. Wear indicator 2. Location mark Tire wear and damage


WARNING


c Tires should be periodically in- spected for wear, cracking, bulg- ing or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


c The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.


c Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified because some tire damage may not be ob- vious. Replace the tires as neces- sary to prevent tire failure and possible personal injury.


technician


c Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact a NISSAN dealer.


c For additional


information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.


Safety


Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.


WARNING


c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.


c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.


this manual


with


the


c When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.


c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.


Maintenance and do-it-yourself 8-43


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


c Do not install a damaged or deformed wheel or tire even if it has been re- paired. Such wheels or tires could have structural damage and could fail with- out warning. c The use of recommended. c For additional


information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.


retread tires


is not


Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage. c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .


8-44 Maintenance and do-it-yourself


Care of wheels c Wash the wheels when washing the vehicle


to maintain their appearance.


c Clean the inner side of the wheels when the is changed or the underside of the


wheel vehicle is washed.


c Do not use abrasive cleaners when washing


the wheels.


c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.


c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.


Spare tire (TEMPORARY USE ONLY spare tire) Observe the following precautions if the TEM- PORARY USE ONLY spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident:


WARNING


c The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid possible tire or differen- tial damage.


c Drive carefully while the TEMPORARY USE ONLY spare tire is installed. Avoid sharp turns and abrupt braking while driving.


c Periodically check spare tire inflation pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar).


c With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 MPH (80 km/h). c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires.


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


c Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear.


c Do not use the spare tire on other


vehicles.


c Do not use more than one spare tire at


the same time.


c Do not tow a trailer when the TEMPO- RARY USE ONLY spare tire is installed.


CAUTION


c Do not use tire chains on a TEMPO- RARY USE ONLY spare tire. Tire chains will not fit properly and may cause dam- age to the vehicle.


c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught.


Maintenance and do-it-yourself 8-45


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


MEMO


8-46 Maintenance and do-it-yourself


9 Technical and consumer information


Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendations . . . . . . . . . . 9-5
Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8


When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification number (VIN) plate . . . . . . . . . . 9-9
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . 9-10
Emission control information label . . . . . . . . . . . . . . . 9-11
Tire and loading information label. . . . . . . . . . . . . . . . 9-11


Air conditioner specification label. . . . . . . . . . . . . . . . 9-11
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . 9-15
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Towing load/specification. . . . . . . . . . . . . . . . . . . . . . . 9-19
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-23
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-24
Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-25
Readiness for inspection/maintenance (I/M) test . . . . . 9-25
Event data recorders (EDR). . . . . . . . . . . . . . . . . . . . . . . . 9-26
Owner(cid:146)s Manual/Service Manual order information . . . 9-27
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-27


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS


The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the (cid:147)Maintenance and do-it-yourself(cid:148) section to determine the proper refill capacity.


Fuel Engine oil *7


Drain and Refill


With oil filter change QR25DE VQ35DE QR25DE VQ35DE


Without oil filter change


Cooling system


With reservoir


Manual transmission gear oil


QR25DE VQ35DE


Continuously Variable Transmission (CVT) fluid Power steering fluid (PSF) Brake and clutch fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system oil Windshield washer fluid


Capacity (Approximate) US measure 20 gal


Imp measure 16-5/8 gal


Liter 75.6


Recommended Fluids and Lubricants


See (cid:147)Fuel recommendation(cid:148) later in this section


4-7/8 qt 4-7/8 qt 4-1/2 qt 4-1/2 qt


2 gal 2-1/8 gal 1-3/4 qt


(cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151)


4 qt 4 qt 3-3/4 qt 3-3/4 qt


1-5/8 gal 1-3/4 gal 1-1/2 qt


(cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151)


4.6
4.6
4.3
4.3


7.6
8.2
1.7


(cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151) (cid:151)


(cid:149) Engine oil with API Certification Mark *2
(cid:149) Viscosity SAE 5W-30 *2


50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85
Genuine NISSAN CVT Fluid NS-2 *3
Genuine NISSAN PSF or equivalent.*4
Genuine NISSAN Super Heavy Duty Brake Fluid *5 or equivalent DOT 3
NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a) *6
NISSAN A/C System Oil Type S or equivalent *6
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze fluid or equivalent


*1: For further details, see (cid:147)Engine oil and oil filter recommendations.(cid:148) *2: Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT transmission, which is not


covered by the NISSAN new vehicle limited warranty.


*3: DEXRON(cid:153) VI type ATF can be used. *4: Available in mainland USA through your NISSAN dealer. *5: For further details, see (cid:147)Air conditioner system refrigerant and oil recommendations.(cid:148) *6: For further details, see (cid:147)Engine Oil(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.


9-2 Technical and consumer information


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


FUEL RECOMMENDATION For 2.5L engine


Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).


For 3.5L engine


NISSAN recommends the use of premium un- leaded gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96). If unleaded premium gaso- line is not available, you may use unleaded regular gasoline with an octane rating of at least 87 AKI number (Research octane number 91), but you may notice a decrease in performance.


CAUTION


c Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.


c Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.


c Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN new vehicle lim- ited warranty.


Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter (WWFC) specifi- cations where it is available. Many of the automo- bile manufacturers developed this specification to improve emission control system and vehicle performance. Ask your service station manager if the gasoline meets the WWFC specifications. Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com-


patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.


If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)


c If an oxygenate-blend other


c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.


Technical and consumer information 9-3


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


fuels,


oxygenate-blend


If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. E(cid:150)85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S. government regulations require fuel ethanol dispensing pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine.


Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy (cid:147)spark knock.(cid:148) ((cid:147)Spark knock(cid:148) is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible.


ignition timing may result


in spark Incorrect knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.


CAUTION


c Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.


c E-85 is a mixture of approximately 85% 15% unleaded


ethanol


and


fuel gasoline.


c U.S. government


regulations require ethanol dispensing pumps to be identi- fied by a small, square, orange and black label with the common abbrevia- tion or the appropriate percentage for that region.


9-4 Technical and consumer information


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See 9Capacities and recommended fuel/lubricants9 earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.


Select only engine oils that meet the American Petroleum Institute (API) certification or Interna- tional Lubricant Standardization and Approval


WTI0183
Committee (ILSAC) certification and SAE vis- cosity standard. These oils have the API certifica- tion mark on the front of the container. Oils which do not have the specified quality label should not be used as they could cause engine damage. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.


Oil which may contain foreign matter or has been previously used should not be used.


Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in (cid:147)Change intervals(cid:148). Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle limited war- ranty.


Technical and consumer information 9-5


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


CAUTION


The use of any other refrigerant or oil will cause severe damage to the air condition- ing system and will require the replace- ment of all air conditioner system components.


The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth(cid:146)s ozone layer. Although this refrigerant does not affect the earth(cid:146)s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.


Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle.


Operation under the following conditions may require more frequent oil and filter changes: c repeated short distance driving at cold out-


side temperatures


c driving in dusty conditions c extensive idling c towing a trailer c stop and go commuting Refer to the (cid:147)NISSAN Service and Maintenance Guide(cid:148) for the maintenance schedule. AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the oil, NISSAN A/C system oil Type S or the exact equiva- lents.


9-6 Technical and consumer information


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


SPECIFICATIONS


ENGINE


Model


Type Cylinder arrangement Bore x Stroke Displacement Firing order


Idle speed M/T CVT (in (cid:147)N(cid:148) position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle


Spark plug


Spark plug gap (Nominal)


QR25DE


VQ35DE


Gasoline, 4-cycle, DOHC 4-cylinder in-line


in (mm) 3.5 x 3.9 (89.0 x 100.0)


cu in (cm3) 151.82 (2,488)


1(cid:150)3(cid:150)4(cid:150)2


Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60(cid:176) 3.760 x 3.205 (95.5 x 81.4) 213.45 (3,498) 1(cid:150)2(cid:150)3(cid:150)4(cid:150)5(cid:150)6


No adjustment is necessary.


DILKAR6A-11


in (mm) 0.043 (1.1)


FXE20HR-11


0.043 (1.1)


Camshaft operation The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.


Timing chain


Timing chain


Technical and consumer information 9-7


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WHEELS AND TIRES


Size 16 x 7JJ 17 x 7 1/2JJ 16 x 4T


Wheel type


Aluminum/Steel Aluminum/Steel T type (Spare)


Tire size


Spare tire


DIMENSIONS AND WEIGHTS


Overall length Overall width Overall height Front track Rear track Wheelbase Gross vehicle weight rating Gross axle weight rating


Front Rear


Offset in (mm) 1.77 (45) 1.77 (45) 1.77 (45)


P215/60R16
P215/55R17
T135/70R16
T135/90R16


in (mm) in (mm) in (mm) in (mm) in (mm) in (mm) lb (kg)


lb (kg) lb (kg)


9-8 Technical and consumer information


Coupe 182.5 (4,636) 70.7 (1,795) 55.3 (1,405) 61.0 (1,549) 60.8 (1,544) 105.3 (2,675)


Sedan 189.8 (4,820) 70.7 (1,795) 57.9 (1,471) 61.0 (1,549) 61.0 (1,549) 109.3 (2,776)


See the (cid:147)F.M.V.S.S./C.M.V.S.S. certification label(cid:148) on the center pillar between the driver(cid:146)s side front and rear doors.


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle(cid:146)s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.


VEHICLE IDENTIFICATION


LTI0025
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.


WTI0037
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.


Technical and consumer information 9-9


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WTI0096


WTI0049


LTI0197


QR25DE


VQ35DE


ENGINE SERIAL NUMBER The number is stamped on the engine as shown.


F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.


9-10 Technical and consumer information


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


WTI0173


EMISSION CONTROL INFORMATION LABEL The emission control tached to the underside of the hood as shown.


information label


is at-


WTI0174
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown.


WTI0178
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed to the underside of the hood as shown.


Technical and consumer information 9-11


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


INSTALLING FRONT LICENSE PLATE


VEHICLE LOADING INFORMATION


Use the following steps to mount the front license plate: s1 Make a shallow hole in each plastic finisher at the location mark (small dimple) using a 0.31 in (8 mm) drill. To avoid damaging the threads behind the finisher, apply only light pressure to the drill.


s2 Mount the license plate bracket using two 8


mm slotted hex head screws.


WARNING


c It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed.


c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.


c Be sure everyone in your vehicle is in a seat and using a seat belt properly.


TERMS It is important to familiarize yourself with the following terms before loading your vehicle: c Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and optional equipment, flu- ids, emergency tools, and spare tire assembly. This weight does not in- clude passengers and cargo.


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


9-12 Technical and consumer information


WTI0179


c GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.


c GVWR (Gross Vehicle Weight Rat- ing) - maximum total combined weight of the unloaded vehicle, pas- sengers, trailer tongue load and any other optional equipment. This information is lo- cated on the F.M.V.S.S./C.M.V.S.S. certification label.


luggage,


hitch,


c GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle. This informa- the tion located F.M.V.S.S./C.M.V.S.S. certification label.


on


is


c GCWR (Gross Combined Weight rating) - The maximum total weight rating of the vehicle, passengers, cargo, and trailer.


c Vehicle Capacity Weight, Load limit, Total load capacity - maximum total weight the load (passengers and cargo) for the ve-


limit specified of


hicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be in- cluded as part of the cargo load. This information is located on the Tire and Loading Information label (if so equipped).


c Cargo capacity - permissible weight of cargo, the subtracted weight of occupants from the load limit.


VEHICLE LOAD CAPACITY Do not exceed the load limit of your ve- hicle shown as (cid:147)The combined weight of occupants and cargo(cid:148) on the Tire and Loading Information label. Do not exceed the number of occupants shown as (cid:147)Seating Capacity(cid:148) on the Tire and Load- ing Information label. To get (cid:147)the combined weight of occu- pants and cargo(cid:148), add the weight of all occupants, then add the total luggage weight. Examples are shown in the follow- ing illustration.


Technical and consumer information 9-13


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


Steps for determining correct load limit 1. Locate the statement (cid:147)The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs(cid:148) on your vehicle(cid:146)s placard.


2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.


3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.


4. The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400-750 (5 X 150) = 650 lbs) or (640-340 (5 X 70) = 300 kg.)


9-14 Technical and consumer information


Example


LTI0152


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the available cargo and lug- gage load capacity of your vehicle.


6.


Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See (cid:147)Measurement of Weights(cid:148) later in this section. Also check tires for proper inflation pres- sures. See the Tire and Loading Informa- tion label.


LOADING TIPS c The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification label.


c Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.


WARNING


c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or colli- sion, unsecured cargo could cause personal injury.


c Do not


load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could oc- cur, or it can change the way your vehicle handles. This could result in loss of control and cause per- sonal injury.


c Overloading not only can shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and longer brak- ing distances. This may cause a premature tire failure which could result in a serious accident and personal injury. Failures caused by overloading are not covered vehicle(cid:146)s warranty.


the


by


MEASUREMENT OF WEIGHTS Secure loose items to prevent weight shifts that could affect the balance of your vehicle. When the vehicle is loaded, drive to a scale and weigh the front and the rear wheels separately to determine axle loads. Individual axle loads should not ex- ceed either of the gross axle weight rat- ings (GAWR). The total of the axle loads should not exceed the gross vehicle weight rating (GVWR). These ratings are given on the vehicle certification label. If weight ratings are exceeded, move or re- move items to bring all weights below the ratings.


Technical and consumer information 9-15


Z REVIEW COPY—2008 Altima (alt) Owners Manual—USA_English (nna) 10/03/07—debbie X


TOWING A TRAILER


WARNING


Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents.


Loading...
x