2009 Mercedes-benz E Class Owners Manual

Otherwise, the wiper motor could suddenly turn on and cause injury. G Warning! Wiper blades are components that are subject to wear and tear. Replace the wiper blades twice a year, preferably in the spring and fall. Otherwise the windows will not be properly wiped. As a result, you may not be able to observe surrounding traffic conditions and could cause an accident.

! To avoid damage to the hood the front wiper arms should only be folded forward when in the vertical position.

! Never open the hood when a front wiper

arm is folded forward. Hold on to the wiper when folding a wiper arm back. If released, the force of the

impact from the tensioning spring could crack the windshield or the rear window (wagon only). Do not allow a wiper arm to contact the windshield glass or the rear window (wagon only) without a wiper blade inserted. For your convenience, we recommend that you have this work carried out at an authorized Mercedes-Benz Center.

Placing wiper arms in vertical position

Wiper arms in vertical position X Make sure the hood is fully closed.

Vehicles with SmartKey X Turn the SmartKey in the starter switch to

position 1.

X Turn combination switch to wiper setting

u.

X With wiper arms in vertical position, turn

the SmartKey in the starter switch to position 0.

X Remove the SmartKey from the starter

switch.

Vehicles with KEYLESS-GO X Turn off the engine.

With the driver’s door closed, the starter switch is now in position 1.

X Turn combination switch to wiper setting

u.

X With wiper arms in vertical position, open

the driver’s door. The starter switch is set to position 0, same as the SmartKey removed from the starter switch.

X Turn combination switch to wiper setting

M.

Removing wiper blades Front wiper blades ! Do not pull on the wiper blade inserts.

They could tear.

X Fold the wiper arms forward until they

engage.

X Turn the wiper blade at a right angle to the

wiper arm.

X Slide the wiper blade sideways out of the

retainer.

Rear wiper blade (wagon) ! Do not pull on the wiper blade insert. It

could tear.

Practical hints

Replacing wiper blades

1 Wiper blade 2 Tab 3 Attachment 4 Removing X Fold the wiper arm away from the rear

window until it engages.

X Turn wiper blade 1 at a right angle to wiper

arm.

X Press tab 2 down and push wiper blade

1 downward in direction of arrow 4.

X Remove wiper blade 1.

353

Practical hints

Replacing wiper blades Installing wiper blades Front wiper blades X Slide the wiper blade onto wiper arm until

it locks in place.

X Rotate the wiper blade into position parallel

to the wiper arm.

X Fold the wiper arm backward to rest on the

windshield. Make sure you hold on to the wiper when folding the wiper arm back.

! Make sure the wiper blades are properly installed. Improperly installed wiper blades may cause windshield damage.

354

Rear wiper blade (wagon)

! Make sure the wiper blade is properly installed. An improperly installed wiper blade may cause rear window damage.

1 Wiper blade 2 Tab 3 Attachment 4 Installing X Slide wiper blade 1 into attachment 3 in

direction of arrow 4.

X Let tab 2 latch into attachment 3 until it

locks in place.

X Check whether the wiper blade is securely

fastened.

X Fold the wiper arm to rest on the rear

window. Make sure to hold on to the wiper when folding the wiper arm back.

Flat tire Safety notes Your vehicle may be equipped with: Ra TIREFIT kit (your vehicle does not have a

spare wheel)

Ra Minispare wheel Ra spare wheel with collapsible tire For information on your vehicle’s equipment, see “Rims and tires” (Y page 384). G Warning! The dimensions of the spare wheel are different from those of the road wheels. As a result, the vehicle handling characteristics change when driving with a spare wheel mounted. Adapt your driving style accordingly. The spare wheel is for temporary use only. When driving with spare wheel mounted, ensure proper tire inflation pressure and do not exceed a vehicle speed of 50 mph (80 km/h). Contact the nearest authorized Mercedes- Benz Center as soon as possible to have the spare wheel replaced with a regular road wheel.

Never operate the vehicle with more than one spare wheel mounted. Do not switch off the ESP® when a spare wheel is mounted.

Preparing the vehicle X Vehicles with AIRMATIC DC:

Make sure the vehicle level is set to normal level (Y page 172).

X Park the vehicle in a safe distance from

moving traffic on a hard, flat surface when possible.

X Turn on the hazard warning flasher. X Turn the steering wheel so that the front wheels are in a straight-ahead position.

X Engage the parking brake. X Shift the automatic transmission into park

position P.

X Turn off the engine. X Remove the SmartKey from the starter

switch.

or X Vehicles with KEYLESS-GO: Open the

driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door can then be closed again.

Practical hints

Flat tire Open doors only when conditions are safe to do so.

X Have any passenger exit the vehicle at a

safe distance from the roadway. Open doors only when conditions are safe to do so.

Sealing tires with TIREFIT This section applies to E 63 AMG (wagon) with third-row seat only. Small tire punctures, particularly those in the tread, can be sealed with TIREFIT. TIREFIT can be used in ambient temperatures down to -4‡ (-20†). G Warning! TIREFIT is a limited repair device. TIREFIT cannot be used for cuts or punctures larger than approximately 0.16 in (4 mm) and tire damage caused by driving with extremely low tire inflation pressure, or on a flat tire, or a damaged wheel. Do not drive the vehicle under such circumstances. Contact the nearest authorized Mercedes- Benz Center for assistance or call Roadside Assistance.

355

Practical hints

Flat tire X Foreign objects (e.g. screws or nails) should not be removed from the tire.

X Take the TIREFIT kit, the sticker, and the

electric air pump out of the cargo compartment (Y page 290).

Two-part sticker 1 Sticker for instrument cluster 2 Sticker for wheel X Attach sticker part 1 where it will be easily

seen by the driver on the instrument cluster.

X Attach sticker part 2 to the damaged tire

(close to the tire valve). G Warning! Take care not to allow the contents of TIREFIT to come in contact with hair, eyes

356

or clothing. TIREFIT is harmful if inhaled, swallowed or absorbed through the skin - causes skin, eye and respiratory irritation. Any contact with eyes or skin should be flushed immediately with plenty of water. If clothing comes in contact with TIREFIT, change clothing as soon as possible. In case of allergic reaction or rash, consult a physician immediately. G Warning! Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. Keep away from open flame or heat source.

i If sealant has leaked out, let it dry. You

can then peel it off. If clothing has come in contact with TIREFIT, have it dry-cleaned with perchloroethylene as soon as possible. G Warning! Observe safety instructions on air pump label.

Your vehicle may be equipped with either of two versions of the electric air pump: RVersion 1: The air hose with pressure

gauge and the electrical plug are located behind a flap.

RVersion 2: The pressure gauge is located

in the pump housing. The air hose and electrical plug are located at the bottom of the pump housing.

The following description applies to both versions. Differences in usage are expressly declared.

Version 1
1 TIREFIT container 2 Notch 3 Electric air pump switch 4 Electrical plug

5 Air hose 6 Flange 7 Flap

X Stick TIREFIT container 1 upside down into notch 2 of the electric air pump.

Practical hints

Flat tire

8 Filler hose 9 Tire valve X Unscrew the valve cap of the damaged tire

from tire valve 9.

Version 2
1 TIREFIT container 2 Notch 3 Electric air pump switch 4 Electrical plug 5 Air hose 6 Flange X Version 1 only: Open flap 7 on the

electric air pump.

X Pull plug 4 and air hose 5 out of the pump

housing.

X Screw the air pump’s air hose 5 onto

flange 6 of TIREFIT container 1.

Version 1
a Vent screw b Pressure gauge X Version 1 only: Close vent screw a on

pressure gauge b.

X Screw filler hose 8 onto tire valve 9. X Insert electrical plug 4 into the cigarette

lighter socket (Y page 223) or a power outlet (Y page 224).

X Turn the SmartKey in the starter switch to

position 1.

or X Vehicles with KEYLESS-GO: Press the

KEYLESS-GO start/stop button once. Do not depress the brake pedal.

357

Practical hints

Flat tire X Press I on electric air pump switch 3.

The electric air pump is switched on and inflates the tire.

i First, the sealing is pumped into the tire. The pressure may briefly rise to up to 73 psi (5 bar). This is normal and not an indication of a malfunction. Do not switch off the electric air pump.

X Let the electric air pump inflate the tire for

approximately 5 minutes. The pressure gauge must display at least 26 psi (1.8 bar). G Warning! The air hose can become hot during inflation. Please exercise appropriate caution.

! Do not operate the electric air pump

longer than 8 minutes without interruption. Otherwise it may overheat. You may operate the air pump again after it has cooled off.

X If the tire inflation pressure of at least

26 psi (1.8 bar) is not attained, turn off the electric air pump by pressing 0 on electric air pump switch 3.

X Detach filler hose 8 from tire valve 9.

358

X Drive vehicle back or forth very slowly

approximately 30 ft (10 m). This serves to better distribute the TIREFIT sealant material inside the tire.

X Unscrew the air pump’s air hose 5 from

flange 6 of TIREFIT container 1.

X Screw air hose 5 onto tire valve 9. X Inflate the tire again. G Warning! If a tire inflation pressure of 26 psi (1.8 bar) is not attained, the tire is too severely damaged for TIREFIT to provide a reliable tire repair. In this case, TIREFIT cannot properly seal the tire. Do not drive the vehicle. Contact the nearest Mercedes-Benz Center or call Roadside Assistance.

X After attaining a tire inflation pressure of at least 26 psi (1.8 bar), press 0 on electric air pump switch 3. The electric air pump is switched off.

X Turn the SmartKey in the starter switch to

position 0.

or X Vehicles with KEYLESS-GO: Press the

KEYLESS-GO start/stop button twice. Do not depress brake pedal.

X Detach the electric air pump. G Warning! The air hose may still be hot. Exercise proper caution to avoid burning yourself when detaching the electric air pump.

X Place the electric air pump back in the

cargo compartment.

X Close the cargo compartment. X Drive off immediately.

The TIREFIT sealant will distribute itself evenly inside the tire. G Warning! Do not exceed a vehicle speed of 50 mph (80 km/h). A TIREFIT repair is not designed to operate at higher speeds.

The sticker must be attached on the instrument cluster where it will be easily seen by the driver. Vehicle handling characteristics of a TIREFIT repaired tire may change. Adapt your driving accordingly.

X After driving the vehicle for an initial 10 minutes, check the tire inflation pressure using pressure gauge on the air pump. G Warning! If tire inflation pressure has fallen below 20 psi (1.3 bar) do not continue to drive the vehicle. Park your vehicle safely away from the roadway and contact the nearest authorized Mercedes-Benz Center or Roadside Assistance. Have the damaged tire replaced.

If the tire inflation pressure is at least 20 psi (1.3 bar), inflate or deflate the tire to the correct tire inflation pressure (see Tire and Loading Information placard on the driver’s door B-pillar):

Version 2
a Deflate button b Pressure gauge X To increase tire inflation pressure: Switch

on the electric air pump.

X Version 1: To decrease tire inflation

pressure, open vent screw a on pressure gauge b (Y page 357).

or X Version 2: To decrease tire inflation

pressure, press yellow deflate button a

Practical hints

Flat tire

located in air pump housing next to pressure gauge b. G Warning! Follow recommend inflation pressures. Do not overinflate tires. Overinflating tires can result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes, etc. Do not underinflate tires. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Do not overload the tires by exceeding the specified vehicle capacity weight (as indicated by the label on the pillar in the driver’s door opening). Overloading the tires can overheat them, possibly causing a blowout.

X Drive to the nearest qualified workshop,

e.g. an authorized Mercedes-Benz Center, to have the damaged tire replaced. X Recommended duration of use: A

maximum of 300 miles (500 km) at 50 mph (80 km/h) or below with the recommended tire inflation pressure.

359

Practical hints

Flat tire X Contact an authorized Mercedes-Benz

Center as soon as possible to obtain a new TIREFIT kit.

X Bring used TIREFIT materials to an

authorized Mercedes-Benz Center for proper disposal.

X Replace your TIREFIT container every 4 years. Replacement containers are available at any authorized Mercedes-Benz Center.

Mounting the spare wheel Introduction X Prepare the vehicle as described

(Y page 355).

X Take the following out of the vehicle:

Rspare wheel Rjack Rwheel wrench Rcollapsible wheel chock Ralignment bolt Relectric air pump (required for vehicles

with spare wheel with collapsible tire only)

360

For information on where to find the respective items, see “Where will I find ...?” (Y page 290) and (Y page 293).

Lifting the vehicle G Warning! When jacking up the vehicle, only use the jack which has been specifically approved by Mercedes-Benz for your vehicle. The jack is designed exclusively for jacking up the vehicle at the jack take-up brackets built into both sides of the vehicle. Make sure the jack arm is fully seated in the jack take-up bracket. The jack must always be vertical when in use, especially on inclines or declines. The jack is intended only for lifting the vehicle briefly for wheel changes. It is not suited for performing maintenance work under the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel change. Never get beneath the vehicle while it is supported by the jack. Keep hands and feet away from the area under the lifted vehicle. Always lower the vehicle onto sufficient capacity jackstands before working under the vehicle.

Always firmly set the parking brake and block the wheels with wheel chocks or other sizeable objects before raising the vehicle with the jack. Do not disengage the parking brake while the vehicle is raised. Make sure that the ground on which the vehicle is standing and where you place the jack is solid, level and not slippery. If necessary, use a large underlay. On slippery surfaces, such as tiled floors, you should use a non-slip underlay, for example a rubber mat. Do not use wooden blocks or similar objects to support the jack. Otherwise the jack may not be able to achieve its load- bearing capacity if it is not at its full height. Never start the engine when the vehicle is raised. Also observe the notes on the jack.

X Prevent the vehicle from rolling away by

blocking wheels with wheel chocks or other sizeable objects. One wheel chock is included with the vehicle tool kit (Y page 290). For information on setting up the collapsible wheel chock, see (Y page 292).

When changing wheel on a level surface: X Place the wheel chock in front of and another wheel chock or other sizeable object behind the wheel that is diagonally opposite to the wheel being changed.

Always try lifting the vehicle using the jack on a level surface. However, should circumstances require you to do so on a hill, place the wheel chock and another sizeable object as follows: X Place wheel chocks or other sizeable

objects on the downhill side blocking both wheels of the axle not being worked on. G Warning! Only jack up the vehicle on level ground or on slight inclines/declines. Otherwise, the vehicle could fall off the jack and injure you or others.

Practical hints

Flat tire ! Do not position the jack on the body of the vehicle, as this may cause damage to the vehicle.

1 Wheel wrench X On wheel to be changed, loosen but do not yet remove the wheel bolts (approximately one full turn with wrench 1).

The jack take-up brackets are located directly behind the front wheel housings and in front of the rear wheel housings. G Warning! The jack is designed exclusively for jacking up the vehicle at the jack take-up brackets. Make sure the jack arm is fully seated in the jack take-up bracket. If you do not position the jack correctly in the jack take-up bracket, the vehicle can fall off the jack and seriously or fatally injure you or others.

2 Take-up bracket 3 Jack 4 Crank X Place jack 3 on firm ground. X Position jack 3 under take-up bracket

2 so that it is always vertical as seen from the side, even if the vehicle is parked on an incline.

361

Practical hints

Flat tire

Removing the wheel

X Turn crank 4 clockwise until jack 3 is

fully seated in take-up bracket 2 and the jack base evenly meets the ground.

X Jack up the vehicle until the wheel is a

maximum of 1.2 in (3 cm) from the ground.

1 Alignment bolt X Unscrew uppermost wheel bolt and remove

it.

X Replace this wheel bolt with alignment bolt

1 supplied with the vehicle tool kit.

X Remove the remaining bolts. ! Do not place wheel bolts in sand or dirt. This could result in damage to the wheel bolts and wheel hub threads.

X Remove the wheel.

362

Attaching the spare wheel G Warning! Vehicles with spare wheel with collapsible tire only: Inflate collapsible tire only after the wheel is properly attached. Inflate the collapsible tire using the electric air pump before lowering the vehicle. G Warning! Always replace wheel bolts that are damaged or rusted. Never apply oil or grease to wheel bolts. Damaged wheel hub threads should be repaired immediately. Do not continue to drive under these circumstances! Contact an authorized Mercedes-Benz Center or call Roadside Assistance. Incorrect wheel bolts or improperly tightened wheel bolts can cause the wheel to come off. This could cause an accident. Be sure to use the correct wheel bolts. G Warning! Only use genuine Mercedes-Benz wheel bolts. Other wheel bolts may come loose. Do not tighten the wheel bolts when the vehicle is raised. Otherwise the vehicle could fall off the jack.

X Clean contact surfaces of wheel and wheel

hub.

! To avoid paint damage, place wheel flat

against hub and hold it there while installing first wheel bolt.

X Guide the spare wheel onto the alignment

bolt and push it on.

X Insert the wheel bolts and tighten them

slightly.

X Unscrew the alignment bolt. X Install last wheel bolt and tighten it slightly. X Vehicles with spare wheel with

collapsible tire: Continue the procedure by following the instructions under “Inflating the collapsible

tire” (Y page 363) and then “Lowering the vehicle” (Y page 365).

or X Vehicles with Minispare wheel: Continue the procedure by following the instructions under “Lowering the vehicle” (Y page 365).

Inflating the collapsible tire G Warning! Inflate collapsible tire only after the wheel is properly attached. Inflate the collapsible tire using the electric air pump before lowering the vehicle. G Warning! Observe safety instructions on air pump label.

! Do not lower the vehicle before inflating the collapsible tire. Otherwise the rim may be damaged.

Practical hints

Flat tire Your vehicle may be equipped with either of two versions of the electric air pump: RVersion 1: The air hose with pressure

gauge and the electrical plug are located behind a flap.

RVersion 2: The pressure gauge is located

in the pump housing. The air hose and electrical plug are located at the bottom of the pump housing.

The following description applies to both versions. Differences in usage are expressly declared.

Version 1
1 Flap 2 Air pump switch 3 Electrical plug

363

Practical hints

Flat tire 4 Air hose with pressure gauge and vent

screw

5 Union nut

X Version 1 only: Close vent screw on air

hose 4.

X Remove the valve cap from the collapsible

tire valve.

X Screw union nut 5 onto the collapsible tire

valve.

X Make sure air pump switch 2 is set to 0. X Insert electrical plug 3 into the cigarette

lighter socket (Y page 223) or a power outlet (Y page 224).

X Turn the SmartKey in the starter switch to

position 1.

or X Vehicles with KEYLESS-GO: Press the

KEYLESS-GO start/stop button on the gear selector lever once. Do not depress the brake pedal.

X Press I on electric air pump switch 2. The electric air pump switches on and inflates the collapsible tire.

X Inflate the collapsible tire to the

recommended tire inflation pressure as specified for your vehicle (Y page 389). This should take approximately 5 minutes. G Warning! The air hose and the union nut can become hot during inflation. Exercise proper

Version 2
2 Air pump switch 3 Electrical plug 4 Pressure gauge 5 Union nut 6 Deflate button X Version 1 only: Open flap 1 on electric

air pump.

X Version 1 only: Pull out electrical plug 3 and air hose with pressure gauge 4.

X Version 2 only: Pull electrical plug 3 and

the air hose out of the pump housing bottom.

364

caution to avoid burning yourself when using the equipment.

! Do not operate the electric air pump

longer than 8 minutes without interruption. Otherwise it may overheat. You may operate the air pump again after it has cooled off.

! Compare the recommended tire inflation

pressure for your vehicle with the tire inflation pressure on the yellow label located on the spare wheel rim. If the tire inflation pressure on the yellow label on the spare wheel rim differs from the values given in this Operator’s Manual, inflate the tire to the recommended tire inflation pressure given on the yellow label on the spare wheel rim.

X Press 0 on electric air pump switch 2. X Turn the SmartKey in the starter switch to

position 0.

or X Vehicles with KEYLESS-GO: Press the

KEYLESS-GO start/stop button on the gear selector lever twice. Do not depress the brake pedal.

X Version 2 only: Store electrical plug 3

and the air hose back into the pump housing bottom.

X Place the electric air pump back in its

designated storage space.

X Lower the vehicle.

Lowering the vehicle G Warning! Vehicles with spare wheel with collapsible tire only: Inflate collapsible tire only after the wheel is properly attached. Inflate the collapsible tire using the electric air pump before lowering the vehicle.

X Lower the vehicle by turning crank

counterclockwise until the vehicle is resting fully on its own weight.

X Remove the jack.

X Version 1 only: If the tire inflation pressure

is above the recommended tire inflation pressure as specified for your vehicle (Y page 389), decrease tire pressure using the vent screw on air hose 4.

X Version 2 only: If the tire inflation pressure

is above the recommended tire inflation pressure as specified for your vehicle (Y page 389), decrease tire pressure using deflate button 6. G Warning! Follow recommend inflation pressures. Do not overinflate tires. Overinflating tires can result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes, etc. Do not underinflate tires. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

X Detach the electric air pump. X Reinstall collapsible tire valve cap. X Version 1 only: Store electrical plug 3
and air hose 4 behind flap 1 and place the electric air pump back in its designated storage space.

Practical hints

Flat tire

1 – 5 Wheel bolts X Tighten the five wheel bolts evenly,

following the diagonal sequence illustrated (1 to 5), until all bolts are tight. Observe a tightening torque of 96 lb-ft (130 Nm). G Warning! Have the tightening torque checked after changing a wheel. The wheels could come loose if they are not tightened to a torque of 96 lb-ft (130 Nm).

X Fully collapse the jack, with handle folded

in (storage position), see (Y page 292).

X Store the jack and the other vehicle tools

in the designated storage space.

For information on storing the spare wheel after it has been replaced by a regular road wheel, see (Y page 293).

365

If the engine still does not start, do not make any further attempts to start the engine. Contact an authorized Mercedes-Benz Center or call Roadside Assistance (Y page 226). i When the malfunction indicator lamp

ú (USA only) or ± (Canada only) in the instrument cluster has been illuminated for the above condition, it will remain illuminated until the engine was cycled on and off four times in a row.

Practical hints

Bleeding the fuel system (diesel engine only) i Vehicles with spare wheel:

Some tire sizes do not allow the damaged road wheel to be stored in the spare wheel well in the trunk/cargo compartment. It should then be transported in the trunk/ cargo compartment wrapped in the protective film/bag that comes with the spare wheel.

i Vehicles with TPMS or Advanced TPMS: Do not restart the tire inflation pressure monitor until a full size wheel/tire with functioning sensor has been placed back into service on the vehicle.

366

Bleeding the fuel system (diesel engine only)

Driving the vehicle until the fuel tank is empty is not recommended. Otherwise, air may be sucked into the fuel system. If this happens, the malfunction indicator lamp ú (USA only) or ± (Canada only) comes on and the engine may not start immediately after refueling the vehicle. After refueling: X Make sure the automatic transmission is in

park position P.

X Do not depress the accelerator. X Turn the SmartKey in the starter switch to

position 2 for at least 10 seconds.

X Return the SmartKey in the starter switch

to position 0.

X Turn the SmartKey in the starter switch to position 3 and hold it there for a maximum of 40 seconds or until the engine runs surge-free.

If the engine does not start: X Wait for approximately 2 minutes. X Turn the SmartKey in the starter switch to position 3 and hold it there for a maximum of 40 seconds or until the engine runs surge-free.

Battery Safety notes A battery should always be sufficiently charged in order to achieve its rated service life. Refer to Maintenance Booklet for battery maintenance intervals. If you use your vehicle mostly for short- distance trips, you will need to have the battery charge checked more frequently. When replacing a battery, always use a battery approved by Mercedes-Benz. If you do not intend to operate your vehicle for an extended period of time, contact an authorized Mercedes-Benz Center about steps you need to observe. G Warning! Observe all safety instructions and precautions when handling automotive batteries.

Risk of explosion.

Fire, open flames and smoking are prohibited when handling batteries. Avoid creating sparks.

Battery acid is caustic. Do not allow it to come into contact with skin, eyes or clothing. Wear suitable protective clothing, especially gloves, apron and faceguard. Wear eye protection. Rinse any acid spills immediately with clear water. Contact a physician if necessary. Keep children away.

Follow the instructions in this Operator’s Manual.

Batteries contain materials that can harm the environment if disposed of improperly. Large 12-volt storage batteries contain lead. Recycling of batteries is the preferred method of disposal. Many states (USA only) or provinces (Canada only) require sellers of batteries to accept old batteries for recycling.

Practical hints

Battery

G Warning! Failure to follow these instructions can result in severe injury or death. Never lean over batteries while connecting. You might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking etc. G Warning! Do not place metal objects on the battery as this could result in a short circuit. Use leak-proof batteries only to avoid the risk of acid burns in the event of an accident. Take care that you do not become statically charged, e.g. by wearing synthetic clothing or rubbing against textiles. For this reason, you also should not pull or push the battery over carpets or other synthetic materials.

367

Practical hints

Battery Never touch the battery first. First touch the outside body of the vehicle in order to release any possible electrostatic charges. Do not rub the battery with rags or cloths. The battery could explode if touched due to electrostatic charge or due to spark formation.

! The battery is a Valve-Regulated Lead Acid (VRLA) battery, also referred to as “fleece” battery. Such batteries do not require topping-up of the electrolyte level. VRLA batteries therefore do not have cell caps and the battery cover is non-removable. Do not attempt to open the battery as otherwise the battery will be damaged. Even though VRLA batteries do not require topping-up of the electrolyte level and cannot be opened to check the electrolyte level, the battery condition must be checked periodically by performing a battery conductance test. Refer to Maintenance Booklet for battery condition testing intervals. The factory-equipped VRLA battery is leak- proofed. Only use a battery as replacement that has the same security features and is

368

of identical size, voltage, and capacity as the factory-equipped battery.

authorized Mercedes-Benz Center for further information.

! As with any other battery, have the

battery disconnect at a qualified workshop or an authorized Mercedes-Benz Center if you do not intend to operate your vehicle for an extended period of time to prevent battery discharge. You may also connect an accessory battery charge unit expressly approved by Mercedes-Benz for your vehicle model to maintain the battery charge. Contact an authorized Mercedes- Benz Center for further information. The battery, the battery ventilation hose and the lateral plug must always be securely installed when the vehicle is in operation.

! Never loosen or detach battery terminal clamps while the engine is running or the SmartKey is in the starter switch or KEYLESS-GO button is in position 1. Otherwise the alternator and other electronic components could be severely damaged. Have the battery checked regularly at an authorized Mercedes-Benz Center. Refer to Maintenance Booklet for maintenance intervals or contact an

i After battery power was interrupted, do

the following: RSynchronize the power windows

(Y page 122).

RSynchronize the tilt/sliding sunroof (Y page 196) or the tilt/sliding panel (Y page 199).

Charging the battery G Warning! Never charge a battery while still installed in the vehicle unless the accessory battery charge unit approved by Mercedes-Benz is being used. Gases may escape during charging and cause explosions that may result in paint damage, corrosion or personal injury. An accessory battery charge unit specially adapted for Mercedes-Benz vehicles and tested and approved by Mercedes-Benz is available, permitting the charging of the battery in its installed position. Contact an authorized Mercedes-Benz Center for information and availability.

Charge battery in accordance with the separate instructions for the accessory battery charger. Have batteries charged at an authorized Mercedes-Benz Center. If you charge the batteries yourself, follow the operating instructions for your charging device. Only use a battery charge unit with a maximum charging voltage of 14.8 V. X Charge battery in accordance with the

instructions of the battery charger manufacturer.

Practical hints

Jump starting transmission which is not covered by the Mercedes-Benz Limited Warranty.

! Jump starting should only be performed using the jump-start terminals located in the engine compartment (wagon). Avoid repeated and lengthy starting attempts. Do not attempt to start the engine using a battery quick-charge unit. If the engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized Mercedes-Benz Center. Excessive unburned fuel generated by repeated failed starting attempts may damage the catalytic converter21 and may present a fire risk. Make sure the jumper cables do not have loose or missing insulation. Make sure the cable clamps do not touch any other metal part while the other end is still attached to a battery.

Jump starting

G Warning! Failure to follow these directions will cause damage to the electronic components, and can lead to a battery explosion and severe injury or death. Never lean over batteries while connecting or jump starting. You might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water, and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking, etc. Attempting to jump start a frozen battery can result in it exploding, causing personal injury. Read all instructions before proceeding.

! Do not tow-start the vehicle. You could

otherwise seriously damage the automatic

21 Vehicles with gasoline engine only.

369

that move when an engine is started or running.

RShould the battery be drained completely, let the donating power source charge the vehicle for several minutes before reattempting the starting process.

X Make sure the two vehicles do not touch. X Switch off all electrical consumers. X Engage the parking brake. X Make sure the automatic transmission is in

park position P.

Sedan The battery is located in the trunk underneath the luggage box (Y page 294). X Open the trunk.

Practical hints

Jump starting If the battery is discharged, the engine can be started with jumper cables and the fully charged battery of another vehicle or an equivalent starter pack. Observe the following: RAccess to the battery is not possible on all vehicles. If you cannot access the battery in your vehicle provide jump start power by an external battery or starter pack.

RJump starting should only be performed

when the engine and catalytic converter22
are cold.

RDo not start the engine if the battery is

frozen. Let the battery thaw out first.

ROnly jump start from batteries with the

same voltage rating (12 V). Jump starting with a more powerful battery could damage the vehicle’s electrical system, which will not be covered by the Mercedes-Benz Limited Warranty.

ROnly use jumper cables with sufficient

cross-section and insulated terminal clamps.

RAlways make sure the jumper cables are not on or near pulleys, fans or other parts

22 Vehicles with gasoline engine only. 370

1 Positive terminal of discharged battery 2 Negative terminal of discharged battery 3 Positive terminal of charged battery 4 Negative terminal of charged battery

! Never invert the terminal connections! X Connect positive terminals 1 and 3 of the batteries with a jumper cable. Clamp the cable to positive terminal 3 of the charged battery first.

X Start engine of the vehicle with the charged

battery and run at idle speed.

X Connect negative terminals 4 and 2 of the batteries with a jumper cable. Clamp the cable to negative terminal 4 of the charged battery first.

X Start engine of the vehicle with the

discharged battery and run at idle speed. You can now turn on the electrical consumers. Do not switch on the headlamps under any circumstances. X Remove the jumper cables first from

negative terminals 2 and 4 and then from positive terminals 1 and 3. You can now switch on the headlamps. X Have the battery checked at the nearest

authorized Mercedes-Benz Center.

Wagon The jump-start terminals are located in the engine compartment on the right hand side. X Open the hood.

1 Negative terminal 2 Cover of positive terminal

! Never invert the terminal connections! X Open cover of the positive terminal 2. X Connect positive terminal of the charged battery with positive terminal 2 with a jumper cable. Clamp the cable to positive terminal of the charged battery first.

X Start engine of the vehicle with the charged

battery and run at idle speed.

X Connect negative terminal of the charged battery with negative terminal 1 with a jumper cable. Clamp the cable to negative terminal 1 of the charged battery first.

Practical hints

Jump starting

X Start engine of the vehicle with the

discharged battery and run at idle speed. You can now turn on the electrical consumers. Do not switch on the headlamps under any circumstances. X Remove the jumper cables first from

negative terminals and then from positive terminals. You can now switch on the headlamps. X Have the battery checked at the nearest

authorized Mercedes-Benz Center.

371

Installing towing eye bolt Depending on whether you are towing a vehicle or you are being towed, the towing eye bolt can be screwed into threaded holes which are located behind covers on each bumper. The towing eye bolt is supplied with the vehicle tool kit, located in the storage compartment underneath the trunk/cargo compartment floor (Y page 290). X Take the vehicle tool kit out of the trunk/

cargo compartment.

Removing cover in front bumper

Practical hints

Towing the vehicle Towing the vehicle Safety notes Mercedes-Benz recommends that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. This method is preferable to other types of towing. ! To prevent damage during transport, do

not tie down vehicle by its chassis or suspension parts.

covered by the Mercedes-Benz Limited Warranty.

RDo not tow with sling-type equipment. Towing with sling-type equipment over bumpy roads will damage radiator and supports.

RTowing of the vehicle should only be

done using the properly installed towing eye bolt. Never attach a tow cable, tow rope or tow rod to the vehicle chassis, frame or suspension parts.

If circumstances do not permit the recommended towing methods, the vehicle may be towed with all wheels on the ground or front axle raised (except vehicles with 4MATIC) only so far as necessary to have the vehicle moved to a safe location where the recommended towing methods can be employed. ! Before towing the vehicle observe the

following instructions: RDo not tow-start the vehicle. You could

otherwise seriously damage the automatic transmission which is not

372

i If the battery is disconnected or

discharged Rthe SmartKey will not turn in the starter

switch

Rthe automatic transmission will remain in

park position P

RFor more information see

“Battery” (Y page 367) or “Jump starting” (Y page 369).

RFor information on manually unlocking

the gear selector lever, see (Y page 345)

1 Cover

X Press mark on cover 1 as indicated by the

arrow.

X Press on cover 1 as indicated by the

arrow.

X Lift cover 1 off to reveal the threaded hole

for the towing eye bolt.

X Fold cover 1 down to reveal the threaded

hole for the towing eye bolt.

Fixing towing eye bolt

Removing cover in rear bumper G Warning! In order to avoid possible serious burns or injury, use extreme caution when removing the rear cover, because the rear exhaust pipe is extremely hot.

1 Cover

Example illustration front bumper 1 Towing eye bolt X Take the towing eye bolt and the wheel

wrench from the vehicle tool kit.

X Screw towing eye bolt 1 clockwise into

threaded hole to its stop.

X Insert wheel wrench into towing eye and tighten towing eye bolt 1 by turning it clockwise.

Practical hints

Towing the vehicle

Removing towing eye bolt X Loosen towing eye bolt 1

counterclockwise with wheel wrench.

X Unscrew towing eye bolt 1. X Reinstalling cover: Fit cover 1

(Y page 372) and snap it into place.

X Store the towing eye bolt and wheel wrench

back into the vehicle tool kit.

Towing with all wheels on the ground G Warning! If circumstances require towing the vehicle with all wheels on the ground, always tow with a tow bar if: Rthe engine will not run Rthere is a malfunction in the brake

system

Rthere is a malfunction in the power supply or in the vehicle’s electrical system

This is necessary to adequately control the towed vehicle.

373

Practical hints

Towing the vehicle Prior to towing the vehicle with all wheels on the ground, make sure the SmartKey is in starter switch position 2. If the SmartKey is left in the starter switch position 0 for an extended period of time, it can no longer be turned in the switch. In this case, the steering is locked. To unlock, remove SmartKey from starter switch and reinsert. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the

brake pedal and keep it pressed.

X Shift the automatic transmission into

neutral position N.

X Release the brake pedal. X If engaged, release the parking brake. X Switch on the hazard warning flasher

(Y page 114).

374

! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

i To signal turns while being towed with the

hazard warning flasher in use you can activate the combination switch for the left or right turn signal in the usual manner – only the selected turn signal will operate. Upon canceling the turn signal, the hazard warning flasher will operate again.

Towing with front axle raised ! Vehicles with 4MATIC: Do not tow with

the front axle raised. Doing so could damage the transfer case, which is not covered by the Mercedes-Benz Limited Warranty. All wheels must be on or off the ground. Observe instructions for towing the vehicle with all wheels on the ground.

When towing the vehicle with the front axle raised, the wheels on the ground have to move freely. X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the

brake pedal and keep it pressed.

X Shift the automatic transmission into

neutral position N.

X Release the brake pedal. X If engaged, release the parking brake. X Switch off the automatic central locking

(Y page 155).

X Switch off the ignition and leave the

SmartKey in the starter switch.

X Switch on the hazard warning flasher

(Y page 114).

! Vehicles without 4MATIC:

Because the ESP® operates automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the vehicle is being towed with the front axle raised. Active braking action through the ESP® may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.

! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

If a newly inserted fuse blows again, have the cause determined and rectified by an authorized Mercedes-Benz Center. A fuse chart is located in the fuse box in the passenger compartment. The fuse chart explains the fuse allocation and fuse amperages.

Before replacing fuses X Engage the parking brake. X Make sure the automatic transmission is in

park position P.

X Switch off all electrical consumers. X Turn off the engine. X Remove the SmartKey from the starter

switch.

X Vehicles with KEYLESS-GO: Open the

driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door then can be closed again.

Fuses Introduction The electrical fuses in your vehicle serve to switch off malfunctioning power circuits. If a fuse is blown, the components and systems secured by that fuse will stop operating. G Warning! Only use fuses approved by Mercedes-Benz with the specified amperage for the system in question and do not attempt to repair or bridge a blown fuse. Using other than approved fuses or using repaired or bridged fuses may cause an overload leading to a fire, and/or cause damage to electrical components and/or systems. Have the cause determined and remedied by an authorized Mercedes-Benz Center. A blown fuse must be replaced by an appropriate spare fuse (recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. i In case of a blown fuse contact Roadside

Assistance or an authorized Mercedes- Benz Center.

Practical hints

Fuses Fuse box in passenger compartment ! Do not use sharp objects such as a

screwdriver to open the fuse box cover in the dashboard. You could damage the fuse box cover or the dashboard.

1 Fuse box cover 2 Recess in the cover X Open the driver’s door. X Insert flat, blunt object as a lever in recess

2 on the edge of cover 1.

X Loosen cover 1 from the dashboard using

the lever.

X Using your hands, pull cover 1 in direction

of arrow and remove it.

375

Opening cover (with turn catches) X Turn catches 1 counterclockwise and

remove cover 2.

Closing cover (with turn catches) X Install cover 2. X Turn catches 1 clockwise.

Opening cover (without turn catches) X Hold cover 2 at recess, press cover 2

slightly together to release tabs from behind trim panel and then pull off cover 2.

Closing cover (without turn catches) X Install cover 2 with tabs on one side of trim panel, then press cover 2 slightly together to install cover 2 on other side of trim panel.

Fuse box in cargo compartment

1 Button for unlocking trim panel 2 Trim panel X Opening: Open the cargo compartment. X Press button 1. X Fold down trim panel 2. X Closing: Fold up trim panel 2.

Practical hints

Fuses X Closing: Hook cover 1 into the opening at

the front.

X Press cover 1 back on until it engages. ! The fuse box cover must be properly

positioned as described to prevent moisture or dirt from entering the fuse box and possibly impairing fuse operation.

Fuse box in trunk (sedan) Fuse box cover design may vary depending on vehicle equipment.

Cover with turn catches shown 1 Catches 2 Cover X Open the trunk.

376

Technical data

Vehicle equipment ............................ 378
Parts service ..................................... 378
Warranty coverage ........................... 378
Identification labels .......................... 379
Engine ................................................ 381
Rims and tires ................................... 384
Electrical system .............................. 390
Main dimensions ............................... 391
Weights .............................................. 393
Fuels, coolants, lubricants etc. ....... 394

377

Technical data

Warranty coverage Vehicle equipment

i This Operator’s Manual describes all

features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.

23 Applicable to vehicles with gasoline engine only. 378

Parts service

Warranty coverage

All authorized Mercedes-Benz Centers maintain a stock of Genuine Mercedes-Benz Parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different parts for Mercedes-Benz models are available. Genuine Mercedes-Benz Parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Genuine Mercedes-Benz Parts should be installed. ! Do not use non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz. Doing so could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty. Also, it could compromise the vehicle’s durability or safety.

Your vehicle is covered under the terms of the warranties printed in the Service and Warranty Information booklet. Your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed in the vehicle in accordance with the terms of the following warranties: RNew Car Limited Warranty REmission System Warranty REmission Performance Warranty RCalifornia, Connecticut, Maine,

Massachusetts, New York, Pennsylvania, Rhode Island, and Vermont Emission Control Systems Warranty23

RState Warranty Enforcement Laws (Lemon

Laws)

Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center.

Loss of Service and Warranty Information booklet Should you lose your Service and Warranty Information booklet, have an authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.

Identification labels

Technical data

Identification labels

Example certification label (U.S. vehicles) 2 VIN 3 Paintwork code

1 Certification label (on driver’s door

B-pillar)

The Vehicle Identification Number (VIN) can be found in the following locations: Ron the certification label Rembossed underneath a cover in the front

passenger footwell (Y page 380)

Ron the lower edge of the windshield

(Y page 380)

Example certification label (Canada vehicles) 2 VIN 3 Paintwork code

379

Technical data

Identification labels i Data shown on certification label are for illustration purposes only. These data are specific to each vehicle and may vary from data shown in the illustration. Refer to certification label on vehicle for actual data specific to your vehicle.

4 Cover 5 VIN X Move the front passenger seat backward

as far as possible (Y page 96).

X Fold cover 4 backward.

VIN 5 is now visible.

6 Emission control information label, includes both federal and California certification exhaust emission standards

7 VIN (on lower edge of windshield) 8 Engine number (engraved on engine)

i When ordering parts, please specify

vehicle identification and engine number.

380

Technical data

Engine

Engine

Model

Engine Mode of operation No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 1349
Maximum torque acc. to SAE J 1349
Maximum engine speed

E 320 BlueTEC (211.022)24

E 300 4MATIC (211.092)24,25

642
Diesel 4-stroke engine 3.27 in (83.00 mm) 3.62 in (92.00 mm) 182.3 cu in (2 987 cm3)

272
4-stroke engine, gasoline injection 3.46 in (88.00 mm) 3.23 in (82.10 mm) 182.9 cu in (2 996 cm3)

E 350 (211.056)24,26
E 350 4MATIC (211.087, 211.287)24
272
4-stroke engine, gasoline injection 3.66 in (92.90 mm) 3.39 in (86.00 mm) 213.5 cu in (3 498 cm3)

16.5:1
209 hp/3 400 rpm (156 kW/3 400 rpm) 400 lb-ft/1 600 rpm - 2 400 rpm (543 Nm/1 600 rpm - 2 400 rpm) 4 500 rpm

11.3:1
228 hp/6 000 rpm (170 kW/6 000 rpm)27
221 lb-ft/2 500 rpm - 5 000 rpm (300 Nm/2 500 rpm - 5 000 rpm) 6 500 rpm

10.7:1
268 hp/6 000 rpm (200 kW/6 000 rpm)27
258 lb-ft/2 400 rpm - 5 000 rpm (350 Nm/2 400 rpm - 5 000 rpm) 6 500 rpm

24 The quoted data apply only to the standard vehicle. Contact an authorized Mercedes-Benz Center for the corresponding data of all special bodies and special equipment. 25 Canada only. 26 USA only. 27 Premium fuel required. Performance may vary with fuel octane rating.

381

Technical data

Engine Model

E 320 BlueTEC (211.022)24

E 300 4MATIC (211.092)24,25

Firing order Poly-V-belt

1-4-2-5-3-6
2 035 mm

1-4-3-6-2-5
2 404 mm

E 350 (211.056)24,26
E 350 4MATIC (211.087, 211.287)24
1-4-3-6-2-5
2 404 mm

382

Technical data

Engine

Model

Engine Mode of operation No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 1349
Maximum torque acc. to SAE J 1349

Maximum engine speed Firing order Poly-V-belt

E 550 (211.072)28,29
E 550 4MATIC (211.090)28
273
4-stroke engine, gasoline injection 3.86 in (98.00 mm) 3.56 in (90.50 mm) 333.3 cu in (5 461 cm3) 10.7:1
382 hp/6 000 rpm (285 kW/6 000 rpm)30
391 lb-ft/2 800 rpm - 4 800 rpm (530 Nm/2 800 rpm - 4 800 rpm) 6 500 rpm 1-5-4-2-6-3-7-8
2 404 mm

E 63 AMG (211.077, 211.27729)28

156
4-stroke engine, gasoline injection 4.02 in (102.20 mm) 3.72 in (94.60 mm) 378.8 cu in (6 208 cm3) 11.3:1
507 hp/6 800 rpm (378 kW/6 800 rpm)30
465 lb-ft/5 200 rpm (630 Nm/5 200 rpm)

7 200 rpm 1-5-4-2-6-3-7-8
2 360 mm

28 The quoted data apply only to the standard vehicle. Contact an authorized Mercedes-Benz Center for the corresponding data of all special bodies and special equipment. 29 USA only. 30 Premium fuel required. Performance may vary with fuel octane rating.

383

Technical data

Rims and tires Rims and tires Notes ! Only use tires which have been tested and

approved by Mercedes-Benz. Tires approved by Mercedes-Benz are developed to provide best possible performance in conjunction with the driving safety systems on your vehicle such as the ABS or the ESP®. Tires specially developed for your vehicle and tested and approved by Mercedes-Benz can be identified by finding the following on the tire’s sidewall: RMO = Mercedes-Benz Original

equipment tires

Using tires other than those approved by Mercedes-Benz may result in damage that is not covered by the Mercedes-Benz Limited Warranty.

! Using tires other than those approved by

Mercedes-Benz can have detrimental effects, such as Rpoor handling characteristics Rincreased noise Rincreased fuel consumption Moreover, tires and rims not approved by Mercedes-Benz may, under load, exhibit

384

not available as standard or optional factory equipment, but can be purchased from an authorized Mercedes-Benz Center. Equipping your vehicle with winter tires approved for your vehicle model may require the purchase of two or four wheel rims of the recommended size for use with these winter tires. This depends on vehicle model and the standard or optional factory- equipped wheel rim/tire configuration on your vehicle. For more information contact an authorized Mercedes-Benz Center.

dimensional variations and different tire deformation characteristics that could cause them to come into contact with the vehicle body or axle parts. Damage to the tires or the vehicle may be the result.

i Further information on tires and rims is

available at any authorized Mercedes-Benz Center. A placard with the recommended tire inflation pressures is located on the driver’s door B-pillar. Some vehicles may have supplemental tire inflation pressure information for driving at high speeds or for vehicle loads less than the maximum loaded vehicle condition. If such information is provided, it can be found on the placard located on the inside of the fuel filler flap. The tire inflation pressure should be checked regularly and should only be adjusted on cold tires. Follow tire manufacturer’s maintenance recommendation included with the vehicle.

For information on recommended tire inflation pressure and supplemental tire inflation pressure information for special driving situations, see (Y page 253). i The following pages also list the approved wheel rim and tire sizes for equipping your vehicles with winter tires. Winter tires are

Same size tires Sedan Model

Rims (light alloy) Wheel offset All season tires33
Winter tires33,34

E 320 BlueTEC

E 35031
E 350 4MATIC31
8.5 J x 17 H2
1.5 in (38 mm) 245/45 R17 95H M+S

8 J x 16 H2
1.42 in (36 mm) 225/55 R16 95H M+S 225/55 R16 95H M+S. 245/45 R17 99V XL (Extra Load)

M+S.

Technical data

Rims and tires

E 300 4MATIC32

8.5 J x 18 H2
1.5 in (38 mm) 245/40 R18 93V M+S 245/40 R18 97V XL (Extra Load) M+S.

31 USA only. 32 Canada only. 33 Radial-ply tires. 34 Not available as factory equipment.

385

E 350 4MATIC36
E 350 4MATIC (AMG Sport Package)35
E 550 4MATIC

E 350 (AMG Sport Package)35
E 55035
E 63 AMG E 63 AMG (Performance Package) 8.5 J x 18 H2
1.5 in (38 mm) — 245/40 R18 97V XL (Extra Load) M+S. 245/40 R18 97V XL (Extra Load) M+S.

8.5 J x 18 H2
1.5 in (38 mm) 245/40 R18 93V M+S

Technical data

Rims and tires Model

AMG rims (light alloy) Wheel offset All-season tires37
Winter tires37,38

35 USA only. 36 Canada only. 37 Radial-ply tires. 38 Not available as factory equipment. 386

Technical data

Rims and tires

Wagon

Model Rims (light alloy) AMG rims (light alloy) Wheel offset All-season tires40
Winter tires40,41

E 350 4MATIC 8 J x 17 H2
— 1.5 in (38 mm) 245/45 R17 95H M+S 245/45 R17 99V XL (Extra Load) M+S. 245/40 R18 97V XL (Extra Load) M+S.42

E 63 AMG39
— 8.5 J x 18 H2
1.5 in (38 mm) —

39 USA only. 40 Radial-ply tires. 41 Not available as factory equipment. 42 Permissible vehicle speed of max. 137 mph (220 km/h).

387

E 350 (AMG Sport Package)43
E 55043
8.5 J x 18 H2
1.5 in (38 mm) — 245/40 R18 93V M+S 9 J x 18 H2