2009 Mercedes-benz E Class Owners Manual

settings: RSeat position RMulticontour seat: previously saved setting

Memory button

1, 2, 3 Memory position button

Storing positions into memory X Adjust the seats. X On the driver’s side, additionally adjust the

steering wheel and exterior rear view mirrors to the desired positions.

X Press memory button M. X Release memory button M and press

memory position button 1, 2 or 3 within 3 seconds. When the settings are stored to the selected position, an acknowledgement signal sounds.

Controls in detail

Memory function

Recalling positions from memory X Press and hold desired memory position

button 1, 2 or 3 until the seat has completely moved to the stored position. On the driver’s side, also wait for the steering wheel and exterior rear view mirrors to move to the stored position. i Releasing the memory position button stops movement to the stored positions immediately.

Storing exterior rear view mirror parking position For easier parking, you can adjust the passenger-side exterior rear view mirror so that you can see the right rear wheel as soon as you engage reverse gear R. For information on activating the parking position, see (Y page 108).

109

X Press memory button M 4. X Within 3 seconds, press bottom of

adjustment button 3. The parking position is stored if the mirror does not move.

i If the mirror does move, repeat the above steps. After the setting is stored, you can move the mirror again.

Lighting Notes i If you drive in countries where vehicles

drive on the other side of the road than the country where the vehicle is registered, you must have the headlamps modified for symmetrical low beams. Relevant information can be obtained at any authorized Mercedes-Benz Center.

i Vehicles equipped with active Bi-Xenon

headlamps: The active Bi-Xenon headlamps monitor the vehicle’s steering angle and speed, then automatically shift their beams to either side to better follow the curvature of the road ahead, increasing usable illumination over conventional headlamps.

Controls in detail

Lighting

1 Driver’s side exterior rear view mirror

button

2 Passenger side exterior rear view mirror

button

3 Adjustment button 4 Memory button M X Stop the vehicle. X Switch on the ignition. X Press button 2.

The passenger-side exterior rear view mirror is selected.

X Adjust the passenger-side exterior rear

view mirror with adjustment button 3 so that you see the rear wheel and the road curb.

110

Exterior lamp switch

$ a Standing lamps, left % g Standing lamps, right & M Off

Daytime running lamp mode ( U Automatic headlamp mode Daytime running lamp mode

) C Parking lamps (also tail lamps,

license plate lamps, side marker lamps and instrument panel lamps) * B Low-beam headlamps or high-beam

headlamps

, ¥ Front fog lamps . † Rear fog lamp

i The exterior lamps go out automatically when you remove the SmartKey from the

starter switch or open the driver’s door with the ignition switched off. When the parking lamps or the rear fog lamp are switched on and you remove the SmartKey from the starter switch and open the driver’s door, an acoustic signal sounds. In addition the message Switch Off Lights appears in the multifunction display. Switch off the parking lamps or the rear fog lamp manually.

! Failure to switch off the parking lamps when leaving the vehicle may result in a discharged battery.

Low-beam headlamps The low-beam headlamps can be switched on and off with the exterior lamp switch. X Switch on the ignition. X Switching on: Turn the exterior lamp

switch to position B. The following lamps come on: RLow-beam headlamps RTail lamps RParking lamps

Controls in detail

Lighting

RLicense plate lamps RSide marker lamps RInstrument panel lamps RGreen indicator lamp B in the

instrument cluster

X Switching off: Turn the exterior lamp

switch to position M.

Automatic headlamp mode The following lamps come on and go out automatically depending on the brightness of the ambient light: RLow-beam headlamps RTail lamps RParking lamps RLicense plate lamps RSide marker lamps G Warning! If the exterior lamp switch is set to U, the headlamps will not automatically come on under foggy conditions. To minimize risk to you and to others, activate headlamps by turning exterior lamp switch to B when driving or when

111

Controls in detail

Lighting traffic and/or ambient lighting conditions require you to do so. In low ambient lighting conditions, only switch from position U to B with the vehicle at a standstill in a safe location. Switching from U to B will briefly switch off the headlamps. Doing so while driving in low ambient lighting conditions may result in an accident. The automatic headlamp feature is only an aid to the driver. The driver is responsible for the operation of the vehicle’s lights at all times.

X Switching on: Turn the exterior lamp

switch to position U. With the SmartKey in starter switch position 1 or the KEYLESS-GO start/stop button pressed once, the tail and parking lamps, the license plate lamps and the side marker lamps will come on and go out depending on the brightness of the ambient light. When the engine is running the low-beam headlamps, the tail and parking lamps, the license plate lamps and the side marker lamps will come on and go out depending on the brightness of the ambient light.

112

Canada only: High-beam headlamps are only available with the exterior lamp switch in position B.

Daytime running lamp mode In Canada, the daytime running lamp mode is mandatory and therefore in a constant mode. In the USA, the daytime running lamp mode is deactivated by default. Activate the daytime running lamp mode using the control system, see “Setting daytime running lamp mode (USA only)” (Y page 153). X Turn the exterior lamp switch to position

M or U. When the engine is running, the low-beam headlamps come on. In low ambient lighting conditions, the following lamps will come on additionally: RTail lamps RParking lamps RLicense plate lamps RSide marker lamps

With the daytime running lamp mode activated and the engine running, you cannot switch off the low-beam headlamps manually.

Canada only With the exterior lamp switch in position M or U, you cannot switch on the high- beam headlamps. The high-beam flasher is available at all times. For nighttime driving turn the exterior lamp switch to position B to permit activation of the high-beam headlamps. When the engine is running, and you Rshift from a driving position to park position P with the vehicle at a standstill, the low- beam headlamps will go out with a delay of 3 minutes

Rturn the exterior lamp switch to position C, the low-beam headlamps, the tail and parking lamps, the license plate lamps and the side marker lamps come on

Rturn the exterior lamp switch to position

B, the manual headlamp mode has priority over the daytime running lamp mode The corresponding exterior lamps come on (Y page 111).

USA only You can only switch on the high-beam headlamps in low ambient lighting conditions. The high-beam flasher is available at all times.

When the engine is running, and you turn the exterior lamp switch to position C or B, the manual headlamp mode has priority over the daytime running lamp mode. The corresponding exterior lamps come on (Y page 111).

Fog lamps Fog lamps cannot be switched on with the exterior lamp switch in position U. To switch on the fog lamps, turn the exterior lamp switch to position B first. G Warning! In low ambient lighting or foggy conditions, only switch from position U to B with the vehicle at a standstill in a safe location. Switching from U to B will briefly switch off the headlamps. Doing so while driving in low ambient lighting conditions may result in an accident. Fog lamps will operate with the parking lamps and/or the low-beam headlamps on. Fog lamps should only be used in conjunction with low-beam headlamps. Consult your State or Province Motor Vehicle Regulations regarding permissible lamp operation.

X Turn the exterior lamp switch to position

C or B (Y page 111).

X Switching on front fog lamps: Pull out the

exterior lamp switch to first stop. The green indicator lamp ¥ in the exterior lamp switch comes on.

X Switching on rear fog lamp: Pull out the

exterior lamp switch to second stop. The rear fog lamp, the front fog lamps and the yellow indicator lamp † in the exterior lamp switch come on.

X Switching off front fog lamps/rear fog lamp: Push in the exterior lamp switch to its stop.

Locator lighting and night security illumination Locator lighting and night security illumination are described in the “Control system” section, see “Setting locator lighting” (Y page 154) and “Setting night security illumination (Headlamps delayed shut-off feature)” (Y page 154).

Controls in detail

Lighting

Combination switch

1 High beam 2 High-beam flasher

High beam X Turn the exterior lamp switch to position

B (Y page 111).

X Switching on: Push the combination

switch in direction of arrow 1. The high-beam headlamp indicator lamp A in the instrument cluster comes on. X Switching off: Pull the combination switch

in direction of arrow 2 to its original position.

113

Controls in detail

Lighting High-beam flasher X Switching on: Pull the combination switch

briefly in direction of arrow 2.

Turn signals

switch only to point of resistance and release. The corresponding turn signal lamps will flash three times.

Hazard warning flasher The hazard warning flasher can be switched on at all times, even with the SmartKey removed from the starter switch. The hazard warning flasher comes on automatically when an air bag deploys.

1 Turn signals, right 2 Turn signals, left X Press the combination switch in direction

of arrow 1 or 2. The corresponding turn signal indicator lamp L or K in the instrument cluster flashes.

The combination switch resets automatically after major steering wheel movements. i To signal minor directional changes such

as changing lanes, press combination

114

1 Hazard warning flasher switch X Switching on: Press hazard warning

flasher switch 1. All turn signal lamps are flashing.

i With the hazard warning flasher activated and the combination switch set for either

left or right turn, only the respective left or right turn signals will operate when the ignition is switched on.

X Switching off: Press hazard warning

flasher switch 1 again.

i If the hazard warning flasher has been

activated automatically, press hazard warning flasher switch 1 once to switch off.

Headlamp cleaning system The headlamps will be cleaned with a high- pressure water jet automatically when the engine is running and you have Rswitched on the headlamps

and

Rthe windshield wipers have wiped the windshield with washer fluid five times

The counter resets when you switch off the ignition. For information on filling up the washer reservoir, see “Washer system and headlamp cleaning system” (Y page 246).

Corner-illuminating front fog lamps The corner-illuminating front fog lamps improve illumination of the area in the direction into which you are turning. The corner-illuminating front fog lamps will only operate Rin low ambient lighting conditions Rat vehicle speeds below 25 mph

(40 km/h)

Rwith the front fog lamps switched off Rwith the engine is running

Switching on X Turn the exterior lamp switch to position

B or U.

or X Activate the daytime running lamp mode

(Y page 112).

X Switch on the left or right turn signal,

depending on whether you are turning left or right. The respective front fog lamp comes on. If you have switched on the turn signal for one side but turn the steering wheel in the other direction, the corner-illuminating

Controls in detail

Lighting

Switching off X Switch off the left or right turn signal. or X Steer straight ahead. i There may be a brief delay before the

corner-illuminating front fog lamps go out.

front fog lamp comes on on the side of the turn signal.

or X Turn steering wheel in the desired

direction. Driving forward: The front fog lamp on the side of your steering direction comes on. Driving in reverse: The front fog lamp opposite to your steering direction comes on.

The corner-illuminating front fog lamps will come on automatically depending on the steering angle, even if you did not switch on either turn signal. If the corner-illuminating front fog lamps came on automatically, they will also go out automatically depending on the steering angle and vehicle speed. The corner-illuminating front fog lamps temporarily come on on both sides of the vehicle if you turn the steering wheel in one direction and then again in the other direction shortly thereafter. The corner-illuminating front fog lamp remains lit for a maximum of 3 minutes. Afterward, it goes out even if the turn signal is still switched on.

115

Controls in detail

Lighting Interior lighting in the front

1 X Left front reading lamp on/off 2 ò Rear interior lighting on/off 3 ¡ Automatic control on/off 4 ð Front interior lighting on/off 5 X Right front reading lamp on/off 6 Interior lighting 7 Ambient lighting 8 Front reading lamps

116

X Switching on/off front interior

lighting: Press switch ð.

X Switching on/off rear interior lighting:

Press switch ò.

X Switching on/off front reading lamps:

Press respective switch X.

Ambient lighting The brightness of the ambient lighting 7 is adjusted via the “Control system” (Y page 154).

Interior lighting in the rear ! An interior lamp switched on manually

does not go out automatically. Leaving an interior lamp switch in the ON position for extended periods of time with the engine turned off could result in a discharged battery.

Automatic control X Activating: Press switch ¡.

The interior lighting comes on in darkness, when you: Runlock the vehicle Rremove the SmartKey from the starter

switch

Ropen a door Ropen the tailgate (wagon)

X Deactivating: Press switch ¡. The interior lighting goes out after a preset time (Y page 155). i If a door remains open, the interior lamps

go out automatically after approximately 5 minutes when the SmartKey is removed or in starter switch position 0.

Manual control ! An interior lamp switched on manually

does not go out automatically. Leaving an interior lamp switch in the ON position for extended periods of time with the engine turned off could result in a discharged battery.

Vehicles with power tilt/sliding sunroof The overhead control panel is located above the rear seat bench.

Sedan: Vehicles with panorama roof

Controls in detail

Lighting ambient lighting 1 and 6 has reached the desired intensity.

You can switch the ambient lighting on and off, using the “Control system” (Y page 154).

1 X Left rear reading lamp on/off 2 Left rear reading lamp 3 Right rear reading lamp 4 X Right rear reading lamp on/off 5 Right rear interior lamp 6 Left rear interior lamp X Switching on/off rear reading lamps:

Press respective reading lamp switch X.

1 Left ambient lighting 2 Left rear interior lamp 3 Ambient lighting switch, to brighten 4 Ambient lighting switch, to dim 5 Right rear interior lamp 6 Right ambient lighting 7 Right rear reading lamp 8 X Right rear reading lamp on/off 9 X Left rear reading lamp on/off a Left rear reading lamp X Switching on/off rear reading lamps:

Press respective reading lamp switch X.

X Dim or brighten rear ambient lighting: Press ambient lighting switch 3 or 4 until

117

Controls in detail

Wipers Wipers Notes ! Do not operate the wipers when the

windshield/rear window is dry. Dust that accumulates on a windshield/rear window might scratch the glass and/or damage the wiper blades when wiping occurs on a dry windshield/rear window. If it is necessary to operate the wipers in dry weather conditions, always operate the wipers with washer fluid.

Combination switch 1 Switching on windshield wipers 2 Single wipe

Wiping with washer fluid

118

X Switch on the ignition.

Windshield wipers Switching on/off

M Windshield wipers off U Slow intermittent wiping

Rain sensor operation with low sensitivity.

V Fast intermittent wiping

Rain sensor operation with high sensitivity.

u Slow continuous wiping t Fast continuous wiping

X Turn the combination switch in direction of

arrow 1 to the desired position, depending on the intensity of the rain.

Intermittent wiping Only switch on intermittent wiping under wet weather conditions or in the presence of precipitation. When you select intermittent wiping, the rain sensor is activated. The rain sensor sets a

suitable wiping interval depending on the wetness of the sensor surface automatically. ! Do not leave windshield wipers on an intermittent setting when the vehicle is taken to an automatic car wash or during windshield cleaning. Windshield wipers will operate in the presence of water sprayed on the windshield, and windshield wipers may be damaged as a result.

! If you have set intermittent wiping, dirt on

the surface of the rain sensor or optical effects may cause the windshield wipers to wipe in an undesired fashion. This could then damage the windshield wiper blades or scratch the windshield. You should therefore switch off the windshield wipers when weather conditions are dry.

X Turn the combination switch to position

U or V. After the initial wipe, pauses between wipes are controlled by the rain sensor automatically.

Intermittent wiping is interrupted when the vehicle is at a standstill and a front door is opened. This protects persons getting into or out of the vehicle from being sprayed. Intermittent wiping will be continued when all doors are closed and

Rthe automatic transmission is in drive

position D or reverse gear R or

Rthe wiper setting is changed using the

combination switch

Single wipe X Press the combination switch briefly in direction of arrow 2 to the resistance point. The windshield wipers wipe one time without washer fluid.

Wiping with washer fluid X Press the combination switch in direction

of arrow 2 past the resistance point. The windshield wipers operate with washer fluid.

i To prevent smears on the windshield or noisy/chattering wiper blades, wipe with washer fluid every now and then even when it is raining.

For information on filling up the washer reservoir, see “Washer system and headlamp cleaning system” (Y page 246).

For information on cleaning the headlamps with washer fluid, see “Headlamp cleaning system” (Y page 114).

Rear window wiper/washer

Combination switch 1 Rear window wiper switch % Wiping rear window with washer fluid & Intermittent wiping ( Rear window wiper off ) Wiping rear window with washer fluid X Switch on the ignition. The rear window wiper engages automatically when the automatic transmission is shifted into reverse gear R with the windshield wipers switched on.

Controls in detail

Wipers X Activating intermittent wiping: Turn rear

window wiper switch 1 to position &. X Deactivating intermittent wiping: Turn rear window wiper switch 1 to position (.

X Wiping with washer fluid: Turn and hold

rear window wiper switch 1 in position % or ) until the rear window is clean.

For information on filling up the washer reservoir, see “Washer system and headlamp cleaning system” (Y page 246).

Problems with wipers ! If anything blocks the windshield wipers

(leaves, snow, etc.), switch them off immediately. For safety reasons, stop the vehicle in a safe location, and R-

remove the SmartKey from the starter switch or turn off the engine by pressing the KEYLESS-GO start/stop button and open the driver’s door (with the driver’s door open, starter switch is in

119

Controls in detail

Power windows

position 0, same as with SmartKey removed from starter switch)

- engage the parking brake before attempting to remove any blockage.

RRemove blockage. RTurn the windshield wipers on again. If the windshield wipers fail to function at all with the combination switch in position U or V, Rset the combination switch to the next

higher wiper speed

Rhave the windshield wipers checked at the nearest authorized Mercedes-Benz Center

120

Power windows Opening and closing The door windows are opened and closed electrically. The switches for all door windows are located on the driver’s door control panel. The switches for the respective door windows are located on the front passenger door and on the rear doors. i Operating the rear door windows from the rear is not possible when you activate the override switch (Y page 69).

Vehicles equipped with the PRE-SAFE® system: If the vehicle is in a critical dynamic driving situation, the door windows close until only a small gap remains. G Warning! When opening or closing the door windows, make sure there is no danger of anyone being harmed by the opening/closing procedure. The door windows are equipped with the express operation and automatic reversal function. If in express operation mode a door window encounters an obstruction that blocks its path, the automatic reversal

function will stop the door window and open it slightly. The door windows operate differently when the switch is pressed and held. See the “Closing when a door window is blocked” section in this chapter for details. The closing of the door windows can be immediately halted by releasing the switch or, if the switch was pulled past the resistance point and released, by either pressing or pulling the respective switch. If a door window encounters an obstruction that blocks its path in a circumstance where you are closing the door windows by pressing and holding button j on the SmartKey or by pressing and holding the lock button (vehicles with KEYLESS-GO) on an outside door handle, the automatic reversal function will not operate. Activate the override switch when children are riding in the back seats of the vehicle. The children may otherwise injure themselves, e.g. by becoming trapped in the door window opening.

G Observe Safety notes, see page 62. G Warning! Do not keep any part of your body up against the window pane when opening a window. The downward motion of the pane may pull that part of your body down between the window pane and the door frame and trap it there. If there is a risk of entrapment, release the switch and pull it to close the window.

i You can also open or close the door

windows using the SmartKey, see “Summer opening feature” (Y page 122) and “Convenience closing feature” (Y page 123).

i After switching off the ignition or

removing the SmartKey from the starter switch, you can operate the door windows until you open the driver’s or front passenger door. If no door was opened you can operate the door windows for up to 5 minutes.

Controls in detail

Power windows X Express operation: Press or pull switch

1 to 4 past the resistance point and release. The corresponding door window opens or closes completely.

X Stopping during express operation:

Press or pull the respective switch again.

1 Left front door window 2 Right front door window 3 Right rear door window 4 Left rear door window X Switch on the ignition. X Opening/Closing: Press or pull and hold switch 1 to 4 to the resistance point. The corresponding door window will move downwards or upwards until you release the switch.

Closing when a door window is blocked G Warning! Make sure that nobody can become trapped and be seriously or even fatally injured when closing a door window with greater force or without automatic reversal function.

If the upward movement of a door window is blocked during the closing procedure, the door window will stop and open slightly. However, the door window will exert greater force before reversing than when the door window is closed in express operation. Please exercise caution! X Immediately after the door window has

stopped because it was blocked, pull the respective switch upwards until the door window is fully closed.

121

Controls in detail

Power windows If the door window is blocked again and opens slightly: X Immediately after the door window was

blocked, pull the respective switch upwards until the door window is fully closed. G Warning! Pressing and holding the switch to close the door window immediately after it had been blocked two times will cause the door window to close without any reversal function for as long as you hold the switch.

Synchronizing door windows The door windows must be synchronized after the battery has been disconnected or if the door windows cannot be fully closed (express operation). Each door window must be synchronized separately. X Close all doors. X Switch on the ignition. X Pull and hold switch 1, 2, 3 or 4
(Y page 121) until the respective door window is closed. The door window opens again slightly.

122

X Pull and hold the respective switch once

more immediately until the door window is completely closed.

X Hold the respective switch for

approximately 1 second. The door window is synchronized.

Summer opening feature If the weather is warm, you can ventilate the vehicle before driving off by simultaneously: Ropening the door windows Ropening the tilt/sliding sunroof Ropening the panorama roof and roller

sunblinds

Rswitching on the seat ventilation for the

driver’s seat

The summer opening feature can only be activated via the remote control of the SmartKey. The SmartKey must be in close proximity to the driver’s outside door handle. X Aim transmitter eye of the SmartKey at the

driver’s outside door handle.

Vehicles with tilt/sliding sunroof X Press and hold button k on the

SmartKey until the door windows and the tilt/sliding sunroof have reached the desired position. The vehicle unlocks.

X Release button k on the SmartKey to

interrupt the opening procedure.

Vehicles with panorama roof (sedan) When roller sunblinds are extended: X Press and hold button k on the

SmartKey. The vehicle unlocks. The door windows open and the roller sunblinds begin to retract after approximately 1 second.

X With the door windows opened and the

roller sunblinds fully retracted, press and hold button k on the SmartKey again. The tilt/sliding panel opens.

X Release button k on the SmartKey to

interrupt the opening procedure. When roller sunblinds are retracted: X Press and hold button k on the

SmartKey. The vehicle unlocks.

The door windows and the tilt/sliding panel opens after approximately 1 second.

X Release button k on the SmartKey to

interrupt the opening procedure.

Convenience closing feature When locking the vehicle, you can simultaneously close Rthe door windows Rthe tilt/sliding sunroof Rthe panorama roof Afterward, you can extend the roller sunblinds of the panorama roof. G Warning! When closing the door windows and the tilt/sliding sunroof or panorama roof, make sure there is no danger of anyone being harmed by the closing procedure. If potential danger exists, proceed as follows: RRelease button j to stop the closing

procedure. To open, press and hold button k. To continue the closing procedure after making sure that there is no danger of anyone being harmed by the

closing procedure, press and hold button j.

Vehicles with KEYLESS-GO: RRelease the lock button on the outside

door handle to stop the closing procedure.

RImmediately pull on the same outside door handle and hold firmly. The door windows and the tilt/sliding sunroof or panorama roof will open for as long as the door handle is held but the door not opened.

With SmartKey The SmartKey must be in close proximity to the driver’s outside door handle. X Aim transmitter eye of the SmartKey at the

driver’s outside door handle.

X Press and hold button j on the

SmartKey until the door windows and the tilt/sliding sunroof or panorama roof are completely closed.

X Release button j on the SmartKey to

interrupt the closing procedure.

Controls in detail

Power windows X Vehicles with panorama roof (sedan):

Press and hold button j on the SmartKey once more. The roller sunblinds extend.

X Release button j on the SmartKey to

interrupt the extending procedure.

With KEYLESS-GO The SmartKey with KEYLESS-GO must be located outside the vehicle within approximately 3 ft (1 m) of a door. X Close all doors. X Press and hold the lock button on an

outside door handle (Y page 83) until the door windows and the tilt/sliding sunroof or panorama roof are completely closed.

X Release the lock button on the outside door handle to interrupt the closing procedure. X Vehicles with panorama roof (sedan):

Press and hold the lock button on an outside door handle once more. The roller sunblinds extend.

X Release the sensor surface to interrupt the

extending procedure.

123

Controls in detail

Driving and parking Driving and parking Safety notes G Warning! Make sure absolutely no objects are obstructing the pedals’ range of movement. Keep the driver’s footwell clear of all obstacles. If there are any floormats or carpets in the footwell, make sure the pedals still have sufficient clearance. During sudden driving or braking maneuvers the objects could get caught between the pedals. You could then no longer brake or accelerate. This could lead to accidents and injury. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

124

Starting the engine G Warning! Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death. Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one window fully open at all times.

Automatic transmission

Gearshift pattern for automatic transmission Á Park position with gear selector lever lock  Reverse gear À Neutral position ¿ Drive position For more information, see “Automatic transmission” (Y page 130). X Make sure the automatic transmission is in

park position P.

With SmartKey X Do not depress the accelerator pedal.

X Gasoline engine: Turn the SmartKey in the starter switch to position 3 (Y page 94) and release it. The engine starts automatically.

X Diesel engine: Turn the SmartKey in the starter switch to position 2 (Y page 94). Preglow indicator lamp q in the instrument cluster comes on.

X As soon as preglow indicator lamp q goes out, turn the SmartKey in the starter switch to position 3 and release it. The engine starts automatically.

i If the engine is at operating temperature, preglow indicator lamp q may not stay on and you can start the engine without preglowing.

With KEYLESS-GO G Warning! As long as the SmartKey is in your vehicle, the vehicle can be started. Therefore, never leave children unattended in the vehicle, as they could otherwise accidentally start the engine. When leaving the vehicle, always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the

vehicle, or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could result in an accident and/or serious personal injury. You can start your vehicle without the SmartKey in the starter switch using the KEYLESS-GO start/stop button on the gear selector lever. The SmartKey must be located in the vehicle.

KEYLESS-GO start/stop button 1 USA only 2 Canada only X Depress the brake pedal during the starting

procedure.

X Do not depress the accelerator pedal.

Controls in detail

Driving and parking X Gasoline engine: Press the KEYLESS-GO

start/stop button once. The engine starts automatically.

X Diesel engine: Press the KEYLESS-GO

start/stop button once. The engine preglows and starts automatically.

i If the engine is at operating temperature,

the time the engine needs to preglow is reduced.

Starting difficulties ! Remember that extended starting

attempts can drain the battery.

If the SmartKey is left in starter switch position 0 for an extended period of time, it can no longer be turned in the starter switch. In this case, the steering is locked. X To unlock, remove the SmartKey from the

starter switch and reinsert.

The engine does not start. You can hear the starter. There could be a malfunction in the engine electronics or in the fuel supply system.

125

Controls in detail

Driving and parking Carry out the following steps: X If you are starting the engine with the

SmartKey: Turn the SmartKey in the starter switch to position 0 and repeat the starting procedure.

X If you are starting the engine with KEYLESS- GO: Close any doors that may be open to allow for better detection of the SmartKey.

or X Start the engine with the SmartKey as radio

signals from another source may be interfering with the KEYLESS-GO function.

X Repeat the starting procedure. If the engine does not start after several starting attempts: X Contact an authorized Mercedes-Benz

Center or call Roadside Assistance.

The engine does not start. You cannot hear the starter. The battery may not be sufficiently charged. X Get a jump start (Y page 369). If the engine will not start despite a jump start: X Contact an authorized Mercedes-Benz

Center or call Roadside Assistance.

126

The starter has been exposed to excessive temperatures. X Let the starter cool for about 2 minutes. X Repeat the starting procedure. If the engine does not start after several starting attempts: X Contact an authorized Mercedes-Benz

Center or call Roadside Assistance.

Driving off G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.

! Do not run cold engine at high engine speeds. Running a cold engine at high engine speeds may shorten the service life of the engine. This is not covered by the Mercedes-Benz Limited Warranty. E 63 AMG: At engine temperatures below 68‡ (20†), the engine’s maximum speed is restricted in order to protect it from damage. Avoid driving your vehicle at full speed when the engine is cold to prevent

premature engine wear and/or diminished comfort.

! If an acoustic warning sounds and the

message Release Parking Brake appears in the multifunction display when driving off, you have forgotten to release the parking brake. Release the parking brake.

! Avoid spinning of a drive wheel. This may

cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

! Simultaneously depressing the

accelerator pedal and applying the brakes reduces engine performance and causes premature brake and drivetrain wear which is not covered by the Mercedes-Benz Limited Warranty.

i Once the vehicle is in motion, the

automatic central locking system engages and the locking knobs in the doors move down. The automatic door lock feature can be deactivated (Y page 155).

Controls in detail

Driving and parking

Automatic transmission G Warning! It is dangerous to shift the automatic transmission out of park position P or neutral position N if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.

! Only shift the automatic transmission into reverse gear R or park position P when the vehicle is stopped. Otherwise the automatic transmission could be damaged.

X Depress the brake pedal.

The gear selector lever lock is released.

X Wait for the gear selection process to complete before setting the vehicle in motion.

X Release the brake pedal. X If engaged, release the parking brake. X Carefully depress the accelerator pedal. After a cold start, the automatic transmission shifts at a higher engine revolution. This allows the catalytic converter (gasoline engine) or the oxidation catalyst (diesel engine) to reach its operating temperature earlier. For more information on driving, see “Driving instructions” (Y page 274).

X Give very little gas. X Have the problem checked at an authorized Mercedes-Benz Center as soon as possible.

The coolant temperature is above 248‡ (120†) The coolant is too hot and is no longer cooling the engine. X Stop the vehicle in a safe location as soon

as possible.

X Turn off the engine immediately. X Allow the engine and coolant to cool off. X Check the coolant level and add coolant if

necessary (Y page 245).

Problems while driving The engine runs erratically and misfires RGasoline engine: An ignition cable may

be damaged.

In case of accident If the vehicle is leaking fuel: X Do not start the engine under any

circumstances.

X Shift the automatic transmission into drive

position D or reverse gear R.

RThe engine electronics may not be

operating properly.

i Shifting the automatic transmission out of

park position P is only possible with the brake pedal depressed. Only depressing the brake pedal releases the gear selector lever lock.

RGasoline engine: Unburned gasoline may have entered the catalytic converter and damaged it.

X Exit the vehicle at a safe distance from the

roadway.

X Notify local fire and/or police authorities. If the extent of the damage cannot be determined: X Contact an authorized Mercedes-Benz

Center or call Roadside Assistance.

127

Controls in detail

Driving and parking If no damage on major assemblies, fuel system, and engine mount can be determined: X Start the engine in the usual manner.

Parking G Warning! Do not park this vehicle in areas where combustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire. To reduce the risk of serious personal injury, or damage to the vehicle or the vehicle drivetrain, as a result of vehicle movement, always do the following before turning off the engine and leaving the vehicle: RKeep right foot on the brake pedal. REngage the parking brake. RShift the automatic transmission into

park position P.

RSlowly release the brake pedal. RWhen parked on an incline, always turn the front wheels towards the road curb.

128

RTurn the SmartKey in the starter switch to position 0 and remove the SmartKey from the starter switch, or press the KEYLESS-GO start/stop button.

RTake the SmartKey with you and lock the

vehicle when leaving. G Warning! Vehicles with AIRMATIC: If you have selected the Comfort suspension tuning, the vehicle lowers slightly when you lock it within approximately 60 seconds after turning off the engine. You should therefore make sure that no one is standing near the wheel arches or lying underneath the vehicle when it is being locked. Otherwise, personal injury could result. Also, make sure your vehicle cannot come into contact with objects, such as a road curb, while lowering. Your vehicle could otherwise be damaged.

Parking brake G Warning! Engaging the parking brake while the vehicle is in motion can cause the rear wheels to lock up. You could lose control of

the vehicle and cause an accident. In addition, the vehicle’s brake lights do not light up when the parking brake is engaged. G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could release the parking brake and/or shift the automatic transmission out of park position P, either of which could result in an accident and/or serious personal injury.

1 Release handle 2 Parking brake pedal

X Releasing: Pull on release handle 1. When the ignition is switched on or the engine is running, the brake warning lamp ; (USA only) or 3 (Canada only) in the instrument cluster goes out. X Engaging: Step firmly on parking brake

pedal 2. When the engine is running, the brake warning lamp ; (USA only) or 3
(Canada only) in the instrument cluster comes on.

Turning off the engine G Warning! Do not turn off the engine before the vehicle has come to a complete stop. With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.

X Shift the automatic transmission into park

position P.

X Engage the parking brake.

i Always engage the parking brake in

addition to shifting the automatic transmission into park position P. When parked on an incline, also turn the front wheels towards the road curb.

With SmartKey X Turn the SmartKey in the starter switch to

position 0.

X Remove the SmartKey from the starter

switch. The immobilizer is activated.

The SmartKey can only be removed from the starter switch with the automatic transmission in park position P.

With KEYLESS-GO X Press the KEYLESS-GO start/stop button. With the driver’s door closed, the starter switch is now in position 1. With the driver’s door opened, the starter switch is set to position 0, same as the SmartKey removed from the starter switch (Y page 94).

If an acoustic warning sounds, you have tried to turn off the engine with the KEYLESS-GO start/stop button while the automatic transmission was not in park position P.

Controls in detail

Driving and parking Read and observe messages that may appear in the multifunction display (Y page 307).

129

Controls in detail

Automatic transmission Automatic transmission Introduction For information on driving with an automatic transmission, see “Driving and parking” (Y page 124). G Warning! Make sure absolutely no objects are obstructing the pedals’ range of movement. Keep the driver’s footwell clear of all obstacles. If there are any floormats or carpets in the footwell, make sure the pedals still have sufficient clearance. During sudden driving or braking maneuvers the objects could get caught between the pedals. You could then no longer brake or accelerate. This could lead to accidents and injury.

! Allow engine to warm up under low load use. Do not place full load on the engine until the operating temperature has been reached. Avoid spinning of a drive wheel for an extended period when driving off on slippery road surfaces. This may cause serious damage to the engine and the drivetrain which is not

130

covered by the Mercedes-Benz Limited Warranty.

i During the brief warm-up, transmission

upshifting is delayed. This allows the catalytic converter (gasoline engine) or oxidation catalyst (diesel engine) to heat up more quickly to operating temperature.

Gear selector lever

Gearshift pattern for automatic transmission Á Park position with gear selector lever lock  Reverse gear À Neutral position ¿ Drive position

G Warning! It is dangerous to shift the automatic transmission out of park position P or neutral position N if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.

! Only shift the automatic transmission into reverse gear R or park position P when the vehicle is stopped. Otherwise the automatic transmission could be damaged.

i Shifting the automatic transmission out of

park position P is only possible with the brake pedal depressed. Only depressing the brake pedal releases the gear selector lever lock.

i The current gear selector lever position corresponds with the current transmission position.

With drive position D selected, you can influence transmission shifting by: Rlimiting the gear range Rextending the gear range Rchanging the gears manually (E 63 AMG

only)

Transmission positions The current transmission position appears in the multifunction display.

1 Transmission position indicator

The current transmission position P, R, N, or D appears in the multifunction display (Y page 131).

There are additional indicators on the cover of the shifting gate showing the current gear selector lever position. The indicators come on when you insert the SmartKey into the starter switch, and go out when you remove the SmartKey from the starter switch.

Shifting procedure The automatic transmission selects individual gears automatically, depending on: Rthe selected gear range (Y page 133) Rthe selected program mode:

C/S (Y page 133) or M (E 63 AMG only) (Y page 135)

Rthe position of the accelerator pedal Rthe vehicle speed

Controls in detail

Automatic transmission

Effect

ì Park position

Shift the automatic transmission into park position P only when the vehicle is stopped. The park position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always engage the parking brake in addition to shifting the automatic transmission into park position P to secure the vehicle. The SmartKey can only be removed from the starter switch with the gear selector lever in park position P. With the SmartKey removed from the starter switch, the gear selector lever is locked in park position P. If the vehicle’s electrical system is malfunctioning, the gear selector lever could remain locked in park position P. To unlock the gear selector lever manually, see “Manually unlocking the gear selector lever” (Y page 345).

í Reverse gear

131

Controls in detail

Automatic transmission

Effect Shift the automatic transmission into reverse gear R only when the vehicle is stopped.

132

Effect

ë Neutral position

No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). To avoid damage to the transmission, never shift the automatic transmission into neutral position N while driving. Exception: If the ESP® is deactivated or malfunctioning, shift the automatic transmission into neutral position N if the vehicle is in danger of skidding. ! Coasting the vehicle, or

driving for any other reason with the automatic transmission in neutral position N can result in transmission damage that is not covered by the Mercedes-Benz Limited Warranty.

ê Drive position

Effect The automatic transmission shifts automatically. All forward gears are available.

Driving tips Kickdown Use the kickdown when you want maximum acceleration. X Depress the accelerator pedal past the

point of resistance. Depending on the engine speed the automatic transmission shifts into a lower gear.

Working on the vehicle G Warning! When working on the vehicle, engage the parking brake and shift the automatic transmission into park position P. Otherwise the vehicle could roll away which could result in an accident and/or serious personal injury.

Gear ranges With the automatic transmission in drive position D and driving in automatic program mode C or S, you can limit or extend the gear range, see “One-touch gearshifting” (Y page 134). The current gear range appears in the multifunction display.

1 Gear range indicator

Controls in detail

Automatic transmission

Effect

è With this selection you can use the

braking effect of the engine.

C Comfort S Sport

For comfort driving For standard driving

ç Allows the use of engine’s braking

power when driving Ron steep downgrades Rin mountainous regions Runder extreme operating

conditions

æ For maximum use of engine’s braking effect on very steep or lengthy downgrades.

Automatic shift program

Program mode selector switch on E 63 AMG C Comfort S Sport M Manual

For standard driving For sporty driving For manual gearshifting (Y page 135)

Program mode selector switch

133

lower revolutions and the wheels are less likely to spin.

Selecting program mode S means that upshifts occur later.

One-touch gearshifting With the automatic transmission in drive position D and driving in automatic program mode C or S, you can limit or extend the gear range using the gear selector lever or the steering wheel gearshift contol. E 63 AMG: For information on using the gear selector lever or the steering wheel gearshift control in manual program mode M, see “Manual shift program” (Y page 135).

Controls in detail

Automatic transmission The current program mode appears in the multifunction display.

1 Program mode indicator You should only change the program mode when the automatic transmission is in park position P. i The last selected automatic program mode (C or S) is switched on when the engine is restarted.

X Press the program mode selector switch repeatedly until the letter of the desired program mode appears in the multifunction display.

Selecting program mode C means: RThe vehicle starts out more gentle, both forward and reverse, except when driving off with full throttle.

RTraction and driving stability are improved

on icy roads.

RUpshifts occur earlier even when you give

more gas. The engine then operates at

134

Steering wheel gearshift control (example illustration) 1 Limiting gear range

Downshift (in manual program mode M)

2 Extending gear range

Upshift (in manual program mode M)

i You cannot shift with the steering wheel

gearshift control when the automatic transmission is in park position P, neutral position N, or reverse gear R.

Limiting gear range G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced

vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.

X Briefly press the gear selector lever to the

left in the D- direction.

or X Briefly pull left gearshift control 1.

The automatic transmission will shift into the next lower gear as permitted by the shift program. This action simultaneously limits the gear range of the automatic transmission.

i To avoid overrevving the engine when

downshifting, the automatic transmission will not shift into a lower gear if the engine’s maximum speed would be exceeded.

Extending gear range X Briefly press the gear selector lever to the

right in the D+ direction.

or X Briefly pull right gearshift control 2.

The automatic transmission will shift into the next higher gear as permitted by the shift program. This action simultaneously extends the gear range of the automatic transmission.

i If you press on the accelerator pedal

when the engine has reached the revolution limit of the current gear range, the automatic transmission will upshift beyond any gear range limit selected.

Canceling gear range limit X Press and hold the gear selector lever to

the right in the D+ direction until D reappears in the multifunction display.

or X Pull and hold right gearshift control 2 until

D reappears in the multifunction display. The automatic transmission will shift from the current gear range directly into drive position D.

Shifting into optimal gear range X Press and hold the gear selector lever to

the left in the D- direction.

or X Pull and hold left gearshift control 1.

The automatic transmission will select the gear range suited for optimal acceleration and deceleration automatically. This will involve shifting down one or more gears.

Controls in detail

Automatic transmission

Manual shift program The manual shift program is available on E 63 AMG only. Manual program mode M differs with regard to spontaneity, response time, and shifting smoothness from automatic program mode S. In manual program mode M, system- controlled automatic gearshifting is switched off. You need to change the gears by manually upshifting or downshifting using the gear selector lever or the steering wheel gearshift control.

Program mode selector switch

135

Controls in detail

Automatic transmission C Comfort S Sport M Manual

For standard driving For sporty driving For manual gearshifting

The current program mode appears in the multifunction display (Y page 134). For information on automatic program mode (C or S), see “Automatic shift program” (Y page 133) and “One-touch gearshifting” (Y page 134).

Activating manual shift program X Press the program mode selector switch

repeatedly until M appears in the multifunction display. The automatic transmission switches to manual program mode M. Automatic shifting is switched off. The gear range is not limited.

You can change the gears manually with drive position D selected. You can upshift or downshift through the gears in succession. i Manual program mode M will not be

stored. When the engine is turned off with manual program mode M selected, the automatic transmission will go to

136

automatic program mode (C or S) when the engine is restarted.

Upshift indicator

Upshifting ! In manual program mode M, the

automatic transmission will not upshift, even if the engine has reached its overrevving range. Shift up into the next gear before the engine has reached its overrevving range. Make absolutely certain that the engine speed does not reach the red marking on the tachometer. Otherwise the engine could be damaged which is not covered by the Mercedes-Benz Limited Warranty.

X Briefly press the gear selector lever to the

right in the D+ direction.

or X Briefly pull right gearshift control 2

(Y page 134). The automatic transmission shifts into the next higher gear.

1 Current gear 2 Upshift indicator In manual program mode M, upshift indicator 2 in the multifunction display advises you to upshift before the engine reaches the overspeed range. In addition, symbol ^ may appear instead of manual program mode symbol M in the multifunction display. Thus you can drive at the maximum engine speed for each gear without overrevving the engine. X Shift the automatic transmission from

current gear 1 into the next higher gear. The fuel supply will otherwise be interrupted to prevent the engine from overrevving.

Downshifting G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.

X Briefly press the gear selector lever to the

left in the D- direction.

or X Briefly pull left gearshift control 1

(Y page 134). The automatic transmission shifts into the next lower gear.

i For maximum acceleration, press and

hold the gear selector lever to the left in the D- direction or pull and hold the left gearshift control. Depending on the engine speed the automatic transmission selects the optimal gear for maximum acceleration.

i When you brake or stop, the automatic transmission shifts down into a gear from which you can easily accelerate or take off.

Kickdown Using the kickdown when driving in manual program mode M is not possible.

Controls in detail

Automatic transmission X Shift the automatic transmission into drive position D (for second gear) or reverse gear R.

X Have the automatic transmission checked at an authorized Mercedes-Benz Center as soon as possible.

Deactivating manual shift program X Press the program mode selector switch

repeatedly until C or S appears in the multifunction display.

or X Restart the engine.

The automatic transmission will go to automatic program mode (C or S).

Manual program mode M is not stored.

Emergency operation (limp-home mode) If vehicle acceleration becomes less responsive or sluggish or the automatic transmission no longer shifts, the automatic transmission is most likely operating in limp- home (emergency operation) mode. In this mode only second gear and reverse gear R can be selected. X Stop the vehicle in a safe location. X Shift the automatic transmission into park

position P.

X Turn off the engine. X Wait at least 10 seconds before restarting. X Restart the engine.

137

Controls in detail

Instrument cluster Instrument cluster Introduction For a full view illustration of the instrument cluster, see “Instrument cluster” (Y page 30). G Warning! No messages will be displayed if either the instrument cluster or the multifunction display is inoperative. As a result, you will not be able to see information about your driving conditions, such as speed or outside temperature, warning/indicator lamps, malfunction/ warning messages or the failure of any systems. Driving characteristics may be impaired. If you must continue to drive, please do so with added caution. Contact an authorized Mercedes-Benz Center as soon as possible.

138

1 Reset button For information on changing the instrument cluster settings, e.g. the language, see (Y page 151).

Activating the instrument cluster The instrument cluster is activated when you Ropen a front door Rswitch on the ignition Rpress reset button 1
Rswitch on the exterior lamps

Adjusting the instrument cluster illumination i The instrument cluster illumination is

dimmed or brightened automatically to suit ambient light conditions. The instrument cluster illumination will also be adjusted automatically when you switch on the vehicle’s exterior lamps.

X To brighten illumination: Turn reset

button 1 clockwise until the desired level of illumination is reached.

X To dim illumination: Turn reset button

1 counterclockwise until the desired level of illumination is reached.

Coolant temperature indicator The coolant temperature indicator is located on the right side in the instrument cluster (Y page 30). G Warning! Driving when your engine is overheated can cause some fluids which may have leaked into the engine compartment to catch fire. You could be seriously burned.

Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it. Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down. During severe operating conditions, e.g. stop- and-go traffic, the coolant temperature may rise close to 248‡ (120†). ! Excessive coolant temperature triggers a warning in the multifunction display and the red coolant temperature warning lamp D in the instrument cluster comes on. The engine should not be operated with a coolant temperature above 248‡ (120†). Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.

Resetting trip odometer X Make sure you are viewing the standard display (Y page 143) in the multifunction display.

X Press and hold the reset button in the

instrument cluster (Y page 138) until the trip odometer is reset.

Tachometer The red marking on the tachometer (Y page 30) denotes excessive engine speed. ! Avoid driving at excessive engine speeds, as it may result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty.

To help protect the engine, the fuel supply is interrupted if the engine is operated within the red marking.

Controls in detail

Control system

Control system Introduction The control system is activated as soon as the starter switch is in position 1 (Y page 94). The control system enables you to call up information about your vehicle and to change vehicle settings. For example, you can use the control system to find out when your vehicle is next due for maintenance service, to set the language for messages in the instrument cluster display, and much more. G Warning! A driver’s attention to the road and traffic conditions must always be his/her primary focus when driving. For your safety and the safety of others, selecting features through the multifunction steering wheel should only be done by the driver when traffic and road conditions permit it to be done safely. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximately 14 m) every second.

139

Controls in detail

Control system The control system relays information to the multifunction display.

Multifunction steering wheel The displays in the multifunction display and the settings in the control system are controlled by the buttons on the multifunction steering wheel.

7 Function only available in telephone menu. 8 AMG vehicles only. 140

1 Multifunction display 2 Press button

s to take a call