2005 Mercedes-benz E Class Wagon Owners Manual

왘 Pull storage box to the rear and remove

it from cargo compartment.

왘 Fold rear seat backrest to the rear

(컄 page 248).

Cargo net

Warning!

The cargo net cannot hold back heavy loads. The transported load should therefore al- ways be tied down.

Objects which are insufficiently secured could otherwise injure you if they are thrown around in the event of an accident, during hard braking or steering maneuvers.

Cargo compartment cover The cargo compartment cover unlocks automatically while the tailgate is open- ing/closing and is automatically raised/ lowered.

When loading the vehicle, make sure not to load the cargo compartment over the lower edge of the side win- dows. The twin roller blind could otherwise be damaged when the tailgate is being closed.

It is therefore unnecessary to roll up the cargo compartment cover before loading and unloading.

1 Cargo net 2 Mountings for cargo net 왘 Pull cargo net 1 up and hook it onto

mountings 2.

You can use the cargo net even when the rear seat backrest is folded for- ward. The cargo net should then be hooked onto the front mountings.

Controls in detail Loading

1 Cargo compartment cover

Rolling up the cargo compartment cover 왘 Unhook cargo compartment cover from its anchorages on the left and right sides.

왘 Slowly guide cargo compartment cover

back until it stops.

257

Controls in detail Loading

Removing the twin roller blind 왘 Roll up cargo net and cargo compart-

ment cover.

왘 Fold both rear seat cushions forward

(컄 page 247).

왘 Push twin roller blind to the left out of its anchorage on the rear seat backrest and remove it.

258

왔 Useful features Storage compartments

Warning!

To help avoid personal injury during a colli- sion or sudden maneuver, exercise care when stowing objects in the vehicle. Put lug- gage or cargo in the cargo compartment if possible. Do not pile luggage or cargo higher than the seat backs.

Luggage nets cannot secure hard or heavy objects.

Keep compartment lids closed. This will help to prevent stored objects from being thrown around and injuring vehicle occupants dur- ing an accident.

Controls in detail Useful features

Parcel net in front passenger footwell

Glove box

A small convenience parcel net is located in the front passenger footwell. It is for small and light items, such as road maps, mail, etc.

1 Glove box lid release 2 Compartment for mobile

phone/glasses

Warning!

Opening the glove box 왘 Push lid release 1.

The parcel net is intended for storing light-weight items only.

Heavy objects, objects with sharp edges or fragile objects may not be transported in the parcel net.

The parcel net cannot protect transported goods in the event of an accident.

The glove box lid opens downward.

Closing the glove box 왘 Push lid up to close.

259

Controls in detail Useful features

Prior to closing the glove box, close the compartment for glasses first.

Storage compartment in the center console (no CD changer* installed)

1 Opening/closing button

260

Storage space under center armrest (Vehicles with cup holder in the center console)

왘 Press button 1 to open.

The control panel swings out upward and the storage compartment extends out.

Never place any medications in the storage compartment. If there is a pow- er failure, the storage compartment cannot be opened.

왘 Press button 1 to close.

1 Storage compartment 2 Storage tray

Opening storage tray 왘 Pull handle 2.

Opening storage compartment 왘 Pull handle 1.

Storage compartment in the rear cen- ter console

Ruffled storage bags

Storage compartment in the rear arm- rest

Controls in detail Useful features

왘 Press the handle upward and fold the

armrest up.

왘 Briefly press the top of the compart-

ment. It extends automatically.

Ruffled storage bags are located on the back of the front seats.

Warning!

The ruffled storage bag is intended for stor- ing light-weight items only.

Heavy objects, objects with sharp edges or fragile objects may not be transported in the ruffled storage bag.

The ruffled storage bag cannot protect transported goods in the event of an acci- dent.

261

Controls in detail Useful features

Cup holders

Depending on production date, your vehi- cle is equipped with cup holders in either the center console (컄 page 262) or in the center armrest (컄 page 263).

Warning!

In order to help prevent spilling liquids on vehicle occupants, only use containers that fit into the cup holder. Use lids on open con- tainers and do not fill containers to a height where the contents, especially hot liquids, could spill during braking, vehicle maneu- vers, or in an accident.

When not in use, keep the cup holder closed. An open cup holder may cause injury to you or others when contacted during braking, vehicle maneuvers, or in an acci- dent.

262

Keep in mind that objects placed in the cup holder may come loose during braking, vehi- cle maneuvers, or in an accident and be thrown around in the vehicle interior. Ob- jects thrown around in the vehicle interior may cause an accident and/or serious per- sonal injury.

Cup holder in the center console

왘 Briefly press the marking in the back of

the cover. The cover opens.

왘 Briefly press marking on the cup hold-

er. The cup holder extends automatically.

The cup holder can be removed for cleaning. Clean the cup holder only with clear, lukewarm water. Make sure to insert the cup holder in the guides when reinstalling it.

Storage compartment with cup holder in the center armrest The storage compartment in the center armrest contains a removable dual cup holder.

Opening storage compartment

1 Left cup holder 2 Right cup holder

Removing cup holder 왘 Take out the cup holder.

Using two fingers in the horizontal slot at the upper rear side of the cup holder, lift cup holder upwards to remove.

1 Cover 왘 Slide cover 1 in direction of arrow 2.

Controls in detail Useful features

Cup holder in the center armrest 3 Dual cup holder 4 Telephone* compartment

Closing storage compartment 왘 Slide cover 1 back.

The cup holder can be removed to in- crease storage space and for cleaning. Clean the cup holder only with clear, lukewarm water. Make sure to insert the cup holder in the guides when reinstalling it (컄 page 264).

263

Controls in detail Useful features

Removing cup holder

Reinstalling cup holder

Rear cup holder

1 Cup holder 2 Locking pins 왘 Move both locking pins 2 in direction

of arrow.

왘 Take cup holder out upward.

3 Locking pins 왘 Insert cup holder. 왘 Move both locking pins 3 in direction

of arrow.

왘 Briefly press the front of the armrest. The cup holder extends automatically.

264

Ashtrays

Removing ashtray insert

Center console ashtray

Warning!

Reinstalling ashtray insert 왘 Install insert by pushing it back into

frame until it engages again.

Controls in detail Useful features

Remove front ashtray only with vehicle standing still. Set the parking brake to se- cure vehicle from movement. Move gear se- lector lever to position N. With gear selector lever in position N, turn off the engine.

왘 Secure vehicle from movement by set- ting the parking brake. Move the gear selector lever to position N. Now you have more room to take out the insert.

왘 Push sliding button 2 to the right and

hold.

Rear seat ashtray

Opening rear seat ashtray 왘 Briefly press the top of the ashtray.

왘 Grip and remove insert from ashtray

The cover opens automatically.

frame.

Opening ashtray 왘 Briefly press the marking on the bot-

tom of cover 1. The cover opens automatically.

265

Controls in detail Useful features

Cigarette lighter

The cigarette lighter is located in the center console compartment in front of the center armrest (컄 page 28).

1 Cigarette lighter 왘 Switch on the ignition. 왘 Push in cigarette lighter 1.

The lighter will pop out automatically when hot.

266

Warning!

12-V socket*

Never touch the heating element or sides of the lighter; they are extremely hot. Hold the knob only.

When leaving the vehicle, always remove the SmartKey or the SmartKey with KEYLESS-GO* from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsu- pervised use of vehicle equipment may cause an accident and/or serious personal injury.

The lighter socket can be used to ac- commodate electrical accessories up to a maximum 85 W.

The socket is located in the rear of the cen- ter console storage compartment. The socket can be used for accessories up to a maximum of 180 W.

An additional socket is located on the left side in the cargo compartment.

Heated steering wheel*

The steering wheel heating warms up the leather area of the steering wheel. The stalk with the heated steering wheel switch is on the lower left-hand side of the steering wheel.

Switching on 왘 Switch on the ignition (컄 page 34). 왘 Turn switch at the tip of stalk in the di-

rection of arrow 3. The steering wheel is heated. Indicator lamp 1 comes on.

Switching off 왘 Turn switch at the tip of stalk in the di-

rection of arrow 2. The heated steering wheel is turned off. Indicator lamp 1 goes out.

1 Indicator lamp 2 Switching off 3 Switching on

Controls in detail Useful features

The steering wheel heating switches off automatically while indicator lamp 1 remains on when 앫 the temperature of the vehicle inte-

rior is above 86°F (30°C)

앫 the temperature of the steering

wheel is above 82°F (28°C)

Indicator lamp 1 flashes or switches off 앫 in case of power surge or undervolt-

age

앫 in case of a steering wheel heating

malfunction

For information on steering wheel, see “Multifunction steering wheel” (컄 page 154).

267

Controls in detail Useful features

Floormats

1 Retainer pin 2 Eyelet

To install or remove the floormat more easily, move the driver’s seat or front passenger seat as far to the rear as possible (컄 page 39).

268

Warning!

Telephone*

Whenever you are using floormats, make sure there is enough clearance and that the floormats are securely fastened.

Floormats should always be securely fas- tened using eyelets 2 and retainer pins 1. Before driving off, check that the floormats are securely in place and adjust them if nec- essary. A loose floormat could slip and hinder proper functioning of the pedals.

Removing 왘 Pull floormat off of retainer pins 1. 왘 Remove the floormat.

Installing 왘 Lay down the floormat. 왘 Press the floormat eyelets 2 onto re-

tainer pins 1.

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or serious personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit, should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. The external antenna must be approved by Mercedes-Benz. Please contact an autho- rized Mercedes-Benz Center for informa- tion on the installation of an approved external antenna. Refer to the radio trans- mitter operation instructions regarding use of an external antenna.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

You can take and place telephone calls us- ing the s and t buttons on the steering wheel. To carry out other tele- phone functions, use the control system (컄 page 179). See separate operating manual for instruc- tions on how to use the telephone.

Controls in detail Useful features

Tele Aid*

The initial activation of the Tele Aid sys- tem may only be performed by com- pleting the subscriber agreement and placing an acquaintance call using the ¡ button. Failure to complete either of these steps will result in a sys- tem that is not activated. If you have any questions regarding ac- tivation, please call the Response Cen- ter at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada).

Warning!

Please do not forget that your primary re- sponsibility is to drive the vehicle. A driver’s attention to the road must always be his /her primary focus when driving. For your safety and the safety of others, we rec- ommend that you pull over to a safe location and stop before placing or taking a tele- phone call. If you choose to use the telephone1 while driving, please use the hands-free device and only use the telephone when road, weather and traffic conditions permit. Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle.

Only operate the COMAND (Cockpit Man- agement and Data System) if road, weather and traffic conditions permit.

1 Observe all legal requirements.

269

Controls in detail Useful features

The Tele Aid system (Telematic Alarm Identification on De- mand) The Tele Aid system consists of three types of response: 앫 automatic and manual emergency 앫 Roadside Assistance and 앫 information The Tele Aid system is operational provid- ing that the vehicle’s battery is charged, properly connected, not damaged and cel- lular and GPS coverage is available. The speaker volume of a Tele Aid call can be adjusted when using the volume control on the multifunction steering wheel. To raise, press button æ and to lower, press button çor use the volume knob on your COMAND headunit.

왘 To activate, press the SOS button, the

Roadside Assistance button • or the Information button ¡, depend- ing on the type of response required.

The SOS button is located above the in- terior rear view mirror. The Roadside Assistance button • and the Information button ¡ are located below the center armrest cov- er.

Shortly after the completion of your ac- quaintance call, you will receive a user ID and password via first call mail. By visiting www.mbusa.com and selecting “Tele Aid” (USA only), you will have access to account information, remote door unlock and more.

The Tele Aid system utilizes the cellular network for communication and the GPS (Global Positioning System) satel- lites for vehicle location. If either of these signals are unavailable, the Tele Aid system may not function and if this occurs, assistance must be sum- moned by other means.

System self-check Initially, after switching on ignition, mal- functions are detected and indicated (the indicator lamps in the SOS button, the Roadside Assistance button • and the Information button ¡ stay on longer than ten seconds or do not come on). The message TELE AID malfunction – Drive to workshop appears for approximately ten seconds in the multifunction display.

270

Warning!

If the indicator lamps in the SOS button, in the Roadside Assistance button and/or in the Information button remain illuminated constantly in red and/or the message TELE AID malfunction – Drive to workshop is displayed in the multifunction display after the system self-check, a mal- function in the system has been detected.

If a malfunction is indicated as outlined above, the system may not operate as ex- pected. Have the system checked at the nearest Mercedes-Benz Center as soon as possible.

Emergency calls An emergency call is initiated automatical- ly following an accident in which the emer- gency tensioning devices (ETDs) or air bags deploy. An emergency call can also be initiated manually by opening the cover next to the interior rear view mirror labeled SOS, then briefly pressing the button located under the cover. See (컄 page 272) for instruc- tions on initiating an emergency call man- ually. Once the emergency call is in progress, the indicator lamp in the SOS button will begin to flash. The message Connecting call appears in the multifunction display. When the connection is established, the mes- sage Call connected appears in the multi- function display. All information relevant to the emergency, such as the location of the vehicle (determined by the GPS satellite lo- cation system), vehicle model, identifica- tion number and color are generated.

Controls in detail Useful features

A voice connection between the Response Center and the occupants of the vehicle will be established automatically soon af- ter the emergency call has been initiated. The Response Center will attempt to deter- mine more precisely the nature of the acci- dent provided they can speak to an occupant of the vehicle.

271

Controls in detail Useful features

The Tele Aid system is available if: 앫 it has been activated and is operation- al. Activation requires a subscription for monitoring services, connection and cellular air time

앫 the relevant cellular phone network

and GPS signals are available and pass the information on to the Response Center

Location of the vehicle on a map is only possible if the vehicle is able to receive signals from the GPS satellite network and pass the information on to the Response Center.

Warning!

If the indicator lamp in the SOS button is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an emergency call (e.g. the rele- vant cellular phone network is not available). The message Call failed appears in the multifunction display for approximately ten seconds.

Should this occur, assistance must be sum- moned by other means.

272

Initiating an emergency call manually

1 Cover 2 SOS button 왘 Briefly press on cover 1.

The cover will open.

왘 Press SOS button 2 briefly.

The indicator lamp in SOS button 2 will flash until the emergency call is concluded.

왘 Wait for a voice connection to the Re-

sponse Center.

왘 Close cover after the emergency call is

concluded.

Warning!

If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, ve- hicle in a dangerous road location), please do not wait for voice contact after you have pressed the emergency button. Carefully leave the vehicle and move to a safe loca- tion. The Response Center will automatically contact local emergency officials with the vehicle’s approximate location if they re- ceive an automatic SOS signal and cannot make voice contact with the vehicle occu- pants.

Controls in detail Useful features

Roadside Assistance button • Located below the center armrest cover is the Roadside Assistance button •. 왘 Press and hold the button (for longer

than two seconds). A call to a Mercedes-Benz Roadside As- sistance dispatcher will be initiated. The button will flash while the call is in progress. The message Connecting call will appear in the multifunction display and the audio system is muted.

When the connection is established, the message Call connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and lo- cation (subject to availability of cellular and GPS signals).

A voice connection between the Roadside Assistance dispatcher and the occupants of the vehicle will be established. 왘 Describe the nature of the need for

assistance.

The Mercedes-Benz Roadside Assistance dispatcher will either dispatch a qualified Mercedes-Benz technician or arrange to tow your vehicle to the nearest authorized Mercedes-Benz Center. For services such as labor and/or towing, charges may ap- ply. Refer to the Roadside Assistance man- ual for more information. These programs are only available in the USA: 앫 Sign and Drive services: Services such as a jump start, a few gallons of fuel or the replacement of a flat tire with the vehicle spare tire are obtainable.

273

Controls in detail Useful features

The indicator lamp on the Roadside As- sistance button • remains illumi- nated in red for approximately ten seconds during the system self-check after switching on ignition (together with the SOS button and the Information button ¡). See system self-check (컄 page 270) when the indicator lamp does not come on in red or stays on longer than ap- proximately ten seconds. If the indicator lamp on the Roadside Assistance button • is flashing con- tinuously and there was no voice con- nection to the Response Center established, then the Tele Aid system could not initiate a Roadside Assis- tance call (e.g. the relevant cellular phone network is not available). The message Call failed appears in the multifunction display.

Roadside Assistance calls can be ter- minated using the t button on the multifunction steering wheel or the re- spective button for ending a telephone call on the COMAND headunit.

Information button ¡ The Information button ¡ is located be- low the center armrest cover. 왘 Press and hold button (for longer than

two seconds). A call to the Customer Assistance Cen- ter will be initiated. The button will flash while the call is in progress. The message Connecting call will appear in the multifunction display and the audio system is muted.

When the connection is established, the message Call connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and lo- cation (subject to availability of cellular and GPS signals).

A voice connection between the Customer Assistance Center representative and the occupants of the vehicle will be estab- lished. When a voice connection is estab- lished. Information regarding the operation of your vehicle, the nearest authorized Mercedes-Benz Center or Mercedes-Benz USA products and services is available to you. For more details concerning the Tele Aid system, please visit www.mbusa.com and use your ID and password (sent to you sep- arately) to learn more (USA only).

The indicator lamp on the Information button ¡ remains illuminated in red for approximately ten seconds during the system self-check after switching on ignition (together with the SOS but- ton and the Roadside Assistance button •).

274

! If the indicator lamps do not start flash- ing after pressing one of the buttons or remain illuminated (in red) at any time, the Tele Aid system has detected a fault or the service is not currently ac- tive, and may not initiate a call. Visit your authorized Mercedes-Benz Center and have the system checked or con- tact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada) as soon as possible.

See system self-check (컄 page 270) when the indicator lamp does not come on in red or stays on longer than ap- proximately ten seconds. If the indicator lamp on the Information button ¡ is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an Information call (e.g. the relevant cellular phone network is not avail- able). The message Call failed ap- pears in the multifunction display. Information calls can be terminated us- ing the t button on the multifunc- tion steering wheel or the respective button for ending a telephone call on the COMAND headunit.

Controls in detail Useful features

Upgrade scenario An emergency call is possible even if other services are active.

The indicator lamp in the respective button flashes until the call is conclud- ed. Calls can only be terminated by a Response Center or Customer Assis- tance Center representative except Roadside Assistance and Information calls, which can also be terminated by pressing button t on the multifunc- tion steering wheel or the respective button for ending a telephone call on the COMAND headunit.

275

Controls in detail Useful features

If the indicator lamp continues to flash or the system does not reset, contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada), or Mercedes-Benz Customer Assistance at 1-800-FOR-MERCedes (1-800-367-6372) in the USA or Cus- tomer Service at 1-800-387-0100 in Canada.

276

When a Tele Aid call has been initiated, the COMAND system audio is muted and the selected mode (radio or CD) pauses. The optional cellular phone (if installed) switches off. If you must use this phone, the vehicle must be parked. Disconnect the coiled cord and place the call. The COMAND navigation* system (if engaged) will continue to run. The display in the instrument clus- ter is available for use, and spoken commands are only available by press- ing the RPT button on the COMAND unit. A pop-up window will appear in the COMAND display to indicate that a Tele Aid call is in progress.

Remote door unlock In case you have locked your vehicle unin- tentionally (e.g. SmartKey inside vehicle), and the reserve SmartKey is not handy: 왘 Contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your pass- word which you provided when you completed the subscriber agreement. 왘 Then return to your vehicle and pull the tailgate recessed handle for a minimum of 20 seconds until the SOS button is flashing. The message Call connected appears in the multifunction display.

As an alternative, you may unlock the vehi- cle via Internet using the ID and password sent to you shortly after the completion of your acquaintance call. The Response Center will then unlock your vehicle with the remote door unlocking feature.

i The remote door unlock feature is avail- able if the relevant cellular phone net- work is available. The SOS button will flash and the mes- sage Call connected will appear in the multifunction display to indicate re- ceipt of the door unlock command. Once the vehicle is unlocked, a Re- sponse Center specialist will attempt to establish voice contact with the ve- hicle occupants. If the tailgate recessed handle was pulled for more than 20 seconds be- fore door unlock authorization was re- ceived by the Response Center, you must wait 15 minutes before pulling the tailgate recessed handle again.

Stolen Vehicle Recovery services In the event your vehicle was stolen: 왘 Report the incident to the police.

The police will issue a numbered inci- dent report.

왘 Pass this number on to the

Mercedes-Benz Response Center along with your password issued to you when you subscribed to the service. The Response Center will then attempt to covertly contact the vehicle’s Tele Aid system. Once the vehicle is lo- cated, the Response Center will con- tact the local law enforcement and you. The vehicle’s location will only be pro- vided to law enforcement.

When the anti-theft alarm or the tow-away alarm stays on for more than 30 seconds, call is initiated automati- cally to the Response Center. See an- ti-theft alarm system (컄 page 98) and tow-away alarm (컄 page 99).

Controls in detail Useful features

Garage door opener

The built-in remote control is capable of operating up to three separately controlled devices, for example garage door openers, gate openers, or other devices compatible with HomeLink® or some other systems. You can program the signal transmitter buttons.

123 Signal transmitter button

Indicator lamp Hand-held transmitter button Hand-held remote control trans- mitter (not part of the vehicle equipment)

277

i Certain types of garage door openers are incompatible with the integrated opener. If you should experience diffi- culties with programming the transmit- ter, contact an authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Center (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.

USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and

(2) this device must accept any inter-

ference received, including interfer- ence that may cause undesired operation.

Any unauthorized modification to this device could void the user’s authority to operate the equipment.

Controls in detail Useful features

Warning!

Before programming the integrated remote control to a garage door opener or gate op- erator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When program- ming a garage door opener, the door moves up or down. When programming a gate oper- ator, the gate opens or closes.

Do not use the integrated remote control with any garage door opener that lacks safe- ty stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufac- tured before April 1, 1982). A garage door that cannot detect an object - signaling the door to stop and reverse - does not meet current U.S. federal safety standards.

278

i Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer-

ence, and

(2) this device must accept any inter-

ference received, including interfer- ence that may cause undesired operation of the device.

Any unauthorized modification to this device could void the user’s authority to operate the equipment.

Programming or reprogramming the in- tegrated remote control Step 1: 왘 Switch on the ignition (컄 page 34). Step 2: 왘 If you have previously programmed an

integrated signal transmitter button and wish to retain its programming, proceed to step 3. Otherwise, press and hold the two outer signal transmit- ter buttons 1 and 3 and release them only when the indicator lamp 4 begins to flash after approximately 20 seconds (do not hold the button for longer than 30 seconds). This proce- dure erases any previous settings for all three channels and initializes the memory. If you later wish to program a second and/or third hand-held trans- mitter to the remaining two signal transmitter buttons, do not repeat this step and begin directly with step 3.

Controls in detail Useful features

Step 3: 왘 Hold the end of the hand-held remote

control transmitter 6 of the device you wish to train approximately 2 to 5 in (5 to12 cm) away from the surface of the integrated remote control locat- ed on the interior rear view mirror, keeping the indicator lamp 4 in view.

Step 4: 왘 Using both hands, simultaneously

press the hand-held transmitter button 5 and the desired integrated signal transmitter button (1, 2 or 3). Do not release the buttons until completing step 5. The indicator lamp 4 on the integrat- ed remote control will flash, first slowly and then rapidly.

컄컄

279

Controls in detail Useful features

컄컄

The indicator lamp 4 flashes the first time the signal transmitter button is programmed. If this button has already been programmed, the indicator lamp will only start flashing after 20 sec- onds.

If the indicator lamp 4 blinks rapidly for about two seconds and then turns to a constant light, continue with pro- gramming steps 8 through 12 as your garage door opener may be equipped with the “rolling code” feature.

Step 7: 왘 To program the remaining two buttons,

repeat the steps above starting with step 3.

Step 5: 왘 When the indicator lamp 4 flashes

rapidly, release both buttons.

Step 6: 왘 Press and hold the just-trained inte- grated signal transmitter button and observe the indicator lamp 4. If the indicator lamp 4 stays on con- stantly, programming is complete and your device should activate when the integrated signal transmitter button is pressed and released.

280

Rolling code programming To train a garage door opener (or other roll- ing code devices) with the rolling code fea- ture, follow these instructions after completing the “Programming” portion (steps 1 through 6) of this text. (A second person may make the following training procedures quicker and easier.) Step 8: 왘 Locate “training” button on the garage

door opener motor head unit. Exact location and color of the button may vary by garage door opener brand. Depending on manufacturer, the “train- ing” button may also be referred to as “learn”or “smart” button. If there is dif- ficulty locating the transmitting button, refer to the garage door opener opera- tor’s manual.

Step 9: 왘 Press “training” button on the garage

door opener motor head unit. The “training light” is activated.

You have 30 seconds to initiate the follow- ing step. Step 10: 왘 Firmly press, hold for two seconds and

release the programmed integrated signal transmitter button (1, 2 or 3).

Step 11: 왘 Press, hold for two seconds and re- lease same button a second time to complete the training process.

Some garage door openers (or other rolling code equipped devices) may require you to perform this procedure a third time to complete the training.

Step 12: 왘 Confirm the garage door operation by pressing the programmed integrated signal transmitter button (1, 2 or 3).

Step 13: 왘 To program the remaining two buttons,

repeat the steps above starting with step 3.

Gate operator/Canadian programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission which may not be long enough for the inte- grated signal transmitter to pick up the sig- nal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.

Controls in detail Useful features

If you live in Canada or if you are having dif- ficulties programming a gate operator (re- gardless of where you live) by using the programming procedures, replace step 4 with the following: Step 4: 왘 Continue to press and hold the inte- grated signal transmitter button (1, 2 or 3) while you press and re-press (“cycle”) your hand-held remote con- trol transmitter 6 every two seconds until the frequency signal has been learned. Upon successful training, the indicator lamp 4 will flash slowly and then rapidly after several seconds.

왘 Proceed with programming step 5 and

step 6 to complete.

281

Controls in detail Useful features

Operation of integrated remote control 왘 Switch on the ignition (컄 page 34). 왘 Select and press the appropriate inte- grated signal transmitter button (1, 2 or 3) to activate the remote con- trolled device. The integrated remote control trans- mitter continues to send the signal as long as the button is pressed – up to 20 seconds.

Erasing the integrated remote control memory 왘 Switch on the ignition (컄 page 34). 왘 Simultaneously hold down the signal transmitter buttons 1 and 3, for ap- proximately 20 seconds, until the indi- cator lamp 4 blinks rapidly. Do not hold for longer than 30 seconds. The codes of all three channels are erased.

282

If you sell your vehicle, erase the codes of all three channels.

Reprogramming a single integrated signal transmitter button To program a device using a signal trans- mitter button previously trained, follow these steps: 왘 Press and hold the desired signal trans- mitter button (1, 2 or 3). Do not re- lease the button.

왘 The indicator lamp will begin to flash af- ter 20 seconds. Without releasing the integrated signal transmitter button, proceed with programming starting with step 3.

Operation The first 1000 miles (1500 km)

Driving instructions

At the gas station

Engine compartment

Tires and wheels

Winter driving

Maintenance

Vehicle care

283

Operation The first 1000 miles (1500 km)

In the “Operation” section you will find de- tailed information on operating, maintain- ing and caring for your vehicle.

284

The more cautiously you treat your vehicle during the break-in period, the more satis- fied you will be with its performance later on. 앫 Drive your vehicle during the first

1000 miles (1500 km) at varying but moderate vehicle and engine speeds. 앫 During this period, avoid heavy loads (full throttle driving) and excessive en- gine speeds (no more than 2/3 of max- imum rpm in each gear).

앫 Avoid accelerating by kick-down. 앫 Do not attempt to slow the vehicle

down by shifting to a lower gear using the selector lever.

앫 Select positions 3, 2 or 1 only when driving at moderate speeds (for hill driving).

앫 Select C as the preferred shift program

(컄 page 188) for the first 1000 miles (1500 km).

After 1000 miles (1500 km) you may gradually increase vehicle and engine speeds to the permissible maximum.

Additional instructions for AMG vehi- cles: 앫 During the first 1000 miles

(1500 km), do not exceed a speed of 85 mph (140 km/h).

앫 During this period, avoid engine speeds above 4500 rpm in each gear.

All of the above, as may apply to your vehi- cle type, also apply when driving the first 1000 miles (1500 km) after the engine or the rear differential has been replaced.

Always obey applicable speed limits.

Operation Driving instructions

Drinking and driving

Pedals

Warning!

Warning!

Keep driver’s foot area clear at all times. Ob- jects stored in this area may impair pedal movement.

Drinking and driving and/or taking drugs and driving are very dangerous combina- tions. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgement.

The possibility of a serious or even fatal ac- cident are greatly increased when you drink or take drugs and drive.

Do not drink or take drugs and drive or allow anyone to drive who has been drinking or taking drugs.

왔 Driving instructions Drive sensibly – save fuel

Fuel consumption, to a great extent, de- pends on driving habits and operating con- ditions. To save fuel you should: 앫 Keep tires at the recommended infla-

tion pressures.

앫 Remove unnecessary loads. 앫 Remove roof rack when not in use. 앫 Allow engine to warm up under low

load use.

앫 Avoid frequent acceleration and decel-

eration.

앫 Have all maintenance work performed

at the intervals specified in the Maintenance Booklet and as required by the Maintenance System. Contact an authorized Mercedes-Benz Center.

Fuel consumption is also increased by driving in cold weather, in stop-and-go traffic, on short trips and in hilly area.

285

Operation Driving instructions

Power assistance

Warning!

The brake system requires electrical energy for operation.

A malfunction in the vehicle’s power supply or electrical system may impair brake sys- tem operation and switch it into its emer- gency operation mode. In such a case, the red brake warning lamp (컄 page 354) and warning messages in the instrument cluster (컄 page 362) come on while driving. To brake, the driver must then apply signifi- cantly greater brake pedal pressure and de- press the pedal much further to obtain the expected braking effect. If necessary, apply full pressure to the brake pedal. Brakes may only be applied to the front wheels. Stop- ping distance is increased!

286

If there is a malfunction in the SBC brake system, we recommend that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. A tow bar must be used if cir- cumstances do not permit the use of the recommended towing methods and the ve- hicle requires towing with all four wheels on the ground. Towing the vehicle with all four wheels on the ground is only permissible for distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h). For more information, refer to “Towing the vehi- cle” (컄 page 430). For more information, see “SBC brake system” (컄 page 92). With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the ve- hicle.

Brakes

Warning!

After driving in heavy rain for some time without applying the brakes or through wa- ter deep enough to wet brake components, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain expected braking ef- fect. Maintain a safe distance from vehicles in front.

Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads.

It can also result in the brakes overheating, thereby significantly reducing their effec- tiveness. It may not be possible to stop the vehicle in sufficient time to avoid an acci- dent.

To help prevent brake disk corrosion after driving on wet road surfaces (particularly salted roads), it is advisable to brake the vehicle with considerable force prior to parking. The heat generated serves to dry the brakes. If your brake system is normally only sub- jected to moderate loads, you should occa- sionally test the effectiveness of the brakes by applying above-normal braking pressure at higher speeds. This will also enhance the grip of the brake pads.

Be very careful not to endanger other road users when you apply the brakes. Refer to the description of the Brake Assist System (BAS) (컄 page 89).

If the parking brake is released and the brake warning lamp in the instrument clus- ter stays on, there is a malfunction in the SBC brake system (컄 page 92) or the brake fluid level in the reservoir is too low. Brake pad wear or a leak in the system may be the reason for low brake fluid in the res- ervoir. Have the brake system inspected by quali- fied technicians immediately. Contact an authorized Mercedes-Benz Center. All checks and service work on the brake system should be carried out by qualified technicians only. Contact an authorized Mercedes-Benz Center. Only install brake pads and brake fluid recommended by Mercedes-Benz.

Operation Driving instructions

Warning!

If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired. This could result in an accident.

Be certain to read and observe the warning notices on brake pad replacement (컄 page 375).

When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps pre- vent overheating of the brakes and re- duces brake pad wear.

After hard braking, it is advisable to drive on for some time, rather than immediately parking, so that the air stream will cool down the brakes faster.

287

Operation Driving instructions

Driving off

Parking

Apply the brakes to test them briefly after driving off. Perform this procedure only when the road is clear of other traffic. Warm up the engine smoothly. Do not place full load on the engine until the oper- ating temperature has been reached. When starting off on a slippery surface, do not allow a drive wheel to spin for an ex- tended period with the ESP switched off. Doing so may cause serious damage to the drive train which is not covered by the Mercedes-Benz Limited Warranty.

Simultaneously depressing the acceler- ator pedal and applying the brake re- duces engine performance and causes premature brake and drivetrain wear.

288

Set the parking brake whenever park- ing or leaving the vehicle. In addition, move gear selector lever to position P. When parking on hills, always set the parking brake and turn front wheel against road curb.

앫 Slowly release brake pedal. 앫 When parked on an incline, turn front

wheel towards the road curb.

앫 Turn the SmartKey to starter switch

position 0 and remove, or press KEYLESS-GO* start/stop button (vehi- cles with KEYLESS-GO*).

앫 Take the SmartKey or the SmartKey with KEYLESS-GO* with you and lock vehicle when leaving.

Warning!

Tires

Do not park this vehicle in areas where com- bustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

To reduce the risk of personal injury as a re- sult of vehicle movement, before turning off the engine and leaving the vehicle always: 앫 Keep right foot on brake pedal. 앫 Firmly depress parking brake pedal. 앫 Move the selector lever to position P.

Warning!

If you feel a sudden significant vibration or ride disturbance, or you suspect that possi- ble damage to your vehicle has occurred, you should turn on the hazard warning flash- ers, carefully slow down, and drive with cau- tion to an area which is a safe distance from the road.

Operation Driving instructions

Inspect the tires and the vehicle underbody for possible damage. If the vehicle or tires appear unsafe, have it towed to the nearest Mercedes-Benz Center or tire dealer for re- pairs.

Treadwear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and be- come visible at a tread depth of approxi- mately 1/16 in (1.6 mm), at which point the tire is considered worn and should be re- placed. The treadwear indicator appears as a solid band across the tread.

Warning!

Warning!

Although the applicable federal motor vehi- cle safety laws consider a tire to be worn when the treadwear indicators (TWI) be- come visible at approximately 1/16 in (1.6 mm), we recommend that you do not al- low your tires to wear down to that level. As tread depth approaches 1/8 in (3 mm), the adhesion properties on a wet road are sharply reduced.

Depending upon the weather and/or road surface (conditions), the tire traction varies widely.

Specified tire inflation pressures must be maintained. This applies particularly if the tires are subjected to high loads (e.g. high speeds, heavy loads, high ambient temper- atures).

Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build-up and possibly a fire.

Hydroplaning

Depending on the depth of the water layer on the road, hydroplaning may occur, even at low speeds and with new tires. Reduce vehicle speed, avoid track grooves in the road and apply brakes cautiously in the rain.

289

Mercedes-Benz recommends M+S rated radial-ply tires with a minimum tread depth of approximately 1/6 in (4 mm) on all four wheels for the winter season to make sure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance compared to summer tires. Stopping distance, however, is still considerably greater than when the road is not covered with snow or ice. Exercise ap- propriate caution.

Avoid spinning of a drive wheel. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

Tire speed rating

Regardless of the tire speed rating, local speed limits should be obeyed. Use pru- dent driving speeds appropriate to prevail- ing conditions.

Warning!

Even when permitted by law, never operate a vehicle at speeds greater than the maxi- mum speed rating of the tires.

Exceeding the maximum speed for which tires are rated can lead to sudden tire fail- ure, causing loss of vehicle control and pos- sibly resulting in an accident and/or personal injury and possible death, for you and for others.

Operation Driving instructions

Tire traction

The safe speed on a wet, snow covered or icy road is always lower than on a dry road. You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point.

Warning!

If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution.

290

E 320, E 320 4MATIC, E 5001, E 500 4MATIC, E 320 (Appearance Package*) E 320 4MATIC (Appearance Package*) E 500 (Appearance Package*) E 500 4MATIC (Appearance Package*) Your vehicle is factory equipped with “H”-rated tires, which have a speed rating of 130 mph (210 km/h).

E 320 4MATIC (Sport Package*), E 500 4MATIC (Sport Package*) Your vehicle is factory equipped with “Y”-rated tires, which have a speed rating of 186 mph (300 km/h). An electronic speed limiter prevents your vehicle from exceeding a speed of 130 mph (210 km/h).

1 Not available in the U.S.

Operation Driving instructions

E 320 (Sport Package*) E 5001 (Sport Package*) Your vehicle is factory equipped with “Z”-rated tires, which have a speed rating of above 149 mph (240 km/h). An electronic speed limiter prevents your vehicle from exceeding a speed of 130 mph (210 km/h).

For information on speed ratings for winter tires, see “Winter driving” (컄 page 337). For additional general information on tire speed markings on tire sidewall, see “Tire speed rating” (컄 page 335).

Winter driving instructions

The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move gear selector lever to position N. Try to keep the vehicle under control by cor- rective steering action.

For more information on driving with snow chains, see “Snow chains” (컄 page 338).

Warning!

On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehi- cle control. Your vehicle’s ABS will not pre- vent this type of control loss.

291

Operation Driving instructions

Road salts and chemicals can adversely af- fect braking efficiency. Increased pedal force may become necessary to produce the normal braking effect. Depressing the brake pedal periodically when traveling at length on salt-strewn roads can bring road-salt-impaired braking efficiency back to normal. If the vehicle is parked after being driven on salt-treated roads, the braking efficien- cy should be tested as soon as possible af- ter driving is resumed.

Warning!

Standing water

If the vehicle becomes stuck in snow, make sure that snow is kept clear of the exhaust pipe and from around the vehicle with the engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle in- terior resulting in unconsciousness and death.

To assure sufficient fresh air ventilation, open a window slightly on the side of the ve- hicle not facing the wind.

Warning!

Warning!

Make sure not to endanger any other road users when carrying out these braking ma- neuvers.

292

The outside temperature indicator is not de- signed to serve as an ice-warning device and is therefore unsuitable for that purpose. In- dicated temperatures just above the freez- ing point do not guarantee that the road surface is free of ice.

For more information, see “Winter driving” (컄 page 337).

Do not drive through flooded areas or water of unknown depth. Before driving through water, determine its depth. Never accelerate before driving into water. The bow wave could force water into the engine and auxiliary equip- ment, thus damaging them. If you must drive through standing wa- ter, drive slowly to prevent water from entering the passenger compartment or the engine compartment. Water in these areas could cause damage to electrical components or wiring of the engine or transmission, or could result in water being ingested by the engine through the air intake causing severe internal engine damage. Any such dam- age is not covered by the Mercedes-Benz Limited Warranty.

Operation Driving instructions

Passenger compartment

Control and operation of radio trans- mitter

Telephones and two-way radios

Warning!

Always fasten items being carried as secure- ly as possible.

In an accident, during hard braking or sud- den maneuvers, loose items will be thrown around inside the vehicle, and cause injury to vehicle occupants unless the items are securely fastened in the vehicle.

The cargo compartment is the preferred place to carry objects.

Driving abroad

Abroad, there is an extensive Mercedes-Benz service network at your disposal. If you plan to drive into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from your authorized Mercedes-Benz Center.

COMAND, radio and telephone*

Warning!

Please do not forget that your primary re- sponsibility is to drive the vehicle safely. Only operate the COMAND (Cockpit Man- agement and Data System), radio or tele- phone1 if road, weather and traffic conditions permit.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

1 Observe all legal requirements

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. Refer to the radio transmitter operation in- structions regarding use of an external an- tenna.

293

Warning!

Emission control

As with any vehicle, do not idle, park or op- erate this vehicle in areas where combusti- ble materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law. These systems, of course, will function properly only when maintained strictly ac- cording to factory specifications. Any ad- justments on the engine should, therefore, be carried out only by qualified Mercedes-Benz Center authorized techni- cians. Engine adjustments should not be altered in any way. Moreover, the specified service jobs must be carried out regularly according to Mercedes-Benz servicing re- quirements. For details refer to the Maintenance Booklet.

Operation Driving instructions

Catalytic converter

Your vehicle is equipped with monolith- ic-type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions. Keep your vehicle in proper operating con- dition by following our recommended maintenance instructions as outlined in your Maintenance Booklet.

To prevent damage to the catalytic con- verters, use only premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, excessive unburned fuel may reach the catalytic converter, causing it to overheat and potentially start a fire.

294

Warning!

Coolant temperature

Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide, and inhaling it can cause uncon- sciousness and lead to death.

Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one win- dow fully open at all times.

During severe operating conditions and stop-and-go city traffic, the coolant tem- perature may rise close to approximately 248°F (120°C). The engine should not be operated with the coolant temperature over 248°F (120°C). Doing so may cause serious en- gine damage which is not covered by the Mercedes-Benz Limited Warranty.

Operation Driving instructions

Warning!

앫 Driving when your engine is badly over-

heated can cause some fluids, which may have leaked into the engine com- partment, to catch fire. You could be se- riously burned.

앫 Steam from an overheated engine can cause serious burns and can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it.

Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.

295

Operation At the gas station

Refueling

Warning!

Gasoline is highly flammable and poisonous. It burns violently and can cause serious injury. Whenever you are around gasoline, avoid inhaling fumes and skin contact, extin- guish all smoking materials. Never allow sparks, flame or smoking materials near gasoline!

The fuel filler flap is located on the right-hand side of the vehicle towards the rear. Locking/unlocking the vehicle with the remote control automatically locks/unlocks the fuel filler flap.

296

왘 Open the fuel filler flap by pushing at

the point indicated by the arrow. The fuel filler flap springs open.

왘 Turn the fuel cap to the left and hold on to it until possible pressure is released. 왘 Take off the cap and set it in the recess

on the fuel filler flap. To prevent fuel vapors from escaping into open air, fully insert filler nozzle unit.

왘 Only fill your tank until the filler nozzle unit cuts out – do not top up or over- fill.

Warning!

Overfilling of the fuel tank may create pres- sure in the system which could cause a gas discharge. This could cause the gas to spray back out when removing the fuel pump noz- zle, which could cause personal injury.

왘 Turn the engine off

앫 by turning the SmartKey to

position 0.

앫 by pressing the KEYLESS-GO*

start/stop button. Open the driv- er’s door (with the driver’s door open, starter switch is now in position 0, same as SmartKey re- moved from starter switch).

왘 Remove the SmartKey from the starter

switch.

i Only use premium unleaded gasoline with a minimum Posted Octane Rating of 91 (average of 96 RON/86 MON). Information on gasoline quality can normally be found on the fuel pump. More information on gasoline can be found in the Factory Approved Service Products pamphlet.

왘 Replace the fuel cap by turning it to the

right. You will hear when the fuel cap is tight- ened.

왘 Close the fuel filler flap.

Leaving the engine running and the fuel cap open can cause the yellow fuel tank reserve warning lamp to flash and the ? malfunction indicator lamp (USA only) or the ± malfunction in- dicator lamp (Canada only) to illumi- nate. For more information, see “Practical hints” (컄 page 357).

Operation At the gas station

Check regularly and before a long trip

1 Windshield washer and headlamp

cleaning system*

2 Brake fluid 3 Coolant level

Opening the hood, see (컄 page 299).

297

Operation At the gas station

Windshield washer system and headlamp cleaning system* For information on refilling the reservoir, see “Windshield washer system and head- lamp cleaning system*” (컄 page 306).

Brake fluid

Coolant For normal replenishing, use water (pota- ble water quality). For more information on coolant, see “Coolant level” (컄 page 303) and see “Fuels, coolants, lubricants etc.” (컄 page 450).

Vehicle lighting Check function and cleanliness. For more information on replacing light bulbs, see “Replacing bulbs” (컄 page 410). For more information, see “Exterior lamp switch” (컄 page 141).

Engine oil level For more information on engine oil level, see (컄 page 300).

Tire inflation pressure For more information on tire inflation pres- sure, see “Checking tire inflation pressure” (컄 page 318).

If you find that the brake fluid in the brake fluid reservoir has fallen to the minimum mark or below, have the brake system checked for brake pad thickness and leaks immediately. Noti- fy an authorized Mercedes-Benz Center immediately. Do not add brake fluid as this will not solve the problem. For more information, see “Practical hints” (컄 page 354).

For information on brake fluid, see “Fuels, coolants, lubricants, etc.” (컄 page 453).

298