Login- Download PDF Manual
-
J_C208_II.book Seite 256 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Engine compartment
256
Windshield washer/headlamp cleaning system
Warning! Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/antifreeze on hot engine parts, because it may burn. You can be seriously burned.
Windshield and headlamp washer fluid mixing ratio
P82.35-2017-26
1 Windshield washer/headlamp cleaning system fluid
reservoir
Capacity approx. 7.4 US qt (7.0 l).
The reservoir should be refilled with MB Windshield washer concentrate and water (or commercially available premixed windshield washer solvent/ antifreeze, depending on ambient temperatures).
For temperatures above freezing: MB Windshield Washer Concentrate “S” and water. 1 part “S” to 100 parts water (40 ml “S” to 1 gallon water).
For temperature below freezing: MB Windshield Washer Concentrate “S” and commercially available premixed windshield washer solvent/antifreeze. 1 part “S” to 100 parts solvent (40 ml “S” to 1 gallon solvent).
J_C208_II.book Seite 257 Donnerstag, 31. Mai 2001 10:13 10
Spare wheel, vehicle tools, storage compartment
P68.00-2253-26
1 Trunk floor 2 Handle 3 Luggage bowl 4 Vehicle tools
Lift trunk floor and engage handle in upper edge of the trunk.
To remove spare tire: Turn luggage bowl counterclockwise and remove.
To store spare tire: Place spare tire in wheel well and secure it with luggage bowl. Turn luggage bowl clockwise to its stop.
Note: Always lower trunk floor before closing trunk lid.
Spare wheel, vehicle jack
257
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 258 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Spare wheel, vehicle jack
Vehicle jack
P40.10-2027-26
1 Jack arm 2 Jack base See illustration for proper storage of jack.
258
Before storing the jack on the felt in the spare wheel well, the jack arm must be lowered almost to the base of the jack.
Warning! The jack is designed exclusively for jacking up the vehicle at the jack tubes built into either side of the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel change. Never get beneath the vehicle while it is supported by the jack. Keep hands and feet away from the area under the lifted vehicle. Always firmly set parking brake and block wheels before raising vehicle with jack. Do not disengage parking brake while the vehicle is raised. Be certain that the jack is always vertical when in use, especially on hills. Always try to use the jack on level surface. Be sure that the jack arm is fully inserted in the jack tube. Always lower the vehicle onto sufficient capacity jackstands before working under the vehicle.
J_C208_II.book Seite 259 Donnerstag, 31. Mai 2001 10:13 10
Wheels Replace rims or tires with the same designation, manufacturer and type as shown on the original part. See your authorized Mercedes-Benz Center for further information. See your authorized Mercedes-Benz Center for information on tested and recommended rims and tires for summer and winter operation. They can also offer advice concerning tire service and purchase.
Tire replacement Front tires should be replaced in sets. Rims and tires must be of the correct size and type. For dimensions, see “Technical Data”. We recommend that you break in new tires for approx. 60 miles (100 km) at moderate speed.
It is imperative that the wheel mounting bolts be fastened to a tightening torque of 80 ft.lb. (110 Nm) whenever wheels are mounted. For rim and tire specifications, refer to “Technical Data”.
Warning! Worn, old tires can cause accidents. If the tire tread is badly worn, or if the tires have sustained damage, replace them. When replacing rims, use only genuine Mercedes-Benz wheel bolts specified for the particular rim type. Failure to do so can result in the bolts loosening and possibly an accident.
Tires, Wheels
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
259
J_C208_II.book Seite 260 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tires, Wheels
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
260
Rotating wheels Wheel rotation applies only when winter tires are mounted on all four wheels. The wheels can be rotated according to the degree of tire wear while retaining the same direction of travel. Rotating, however, should be carried out as recommended by the tire manufacturer, before the characteristic tire wear pattern (shoulder wear on front wheels and tread center wear on rear wheels) becomes visible, as otherwise the driving properties deteriorate.
Important! Unidirectional tires must always be mounted with arrow on tire sidewall pointing in direction of vehicle forward movement.
Notes: Thoroughly clean the inner side of the wheels any time you rotate the wheels or wash the vehicle underside. The use of retread tires is not recommended. Retread tires may adversely affect the handling characteristics and safety of the vehicle. Dented or bent rims can cause tire pressure loss and damage to the tire beads. For this reason, check rims for damage at regular intervals. The rim flanges must be checked for wear before a tire is mounted. Remove burrs, if any. Check and ensure proper tire inflation pressure after rotating the wheels. For tire inflation pressure see inside of fuel filler flap and also page 267.
J_C208_II.book Seite 261 Donnerstag, 31. Mai 2001 10:13 10
Spare wheel
Important! The spare wheel rim size is 71/2 J x 17 H 2. The spare wheel rim is mounted with a full size tire of the same type as on the vehicle’s front axle, and is fully functional. However, that spare wheel rim is weight optimized and has a limited service life of 12 000 miles (20 000 km) use before a standard wheel rim must replace it. In the case of a rear axle flat tire, you may temporarily use the spare wheel, when observing the following restrictions: • Do not exceed vehicle speed of 50 mph (80 km/h). • Drive to the nearest tire repair facility to have the
flat tire repaired or replaced as appropriate.
• Do not operate vehicle with more than one spare
wheel mounted.
If the arrow on tire side wall does not point in direction of vehicle forward movement when using the spare wheel, observe the following restriction:
Unidirectional tires must always be mounted with arrow on tire sidewall pointing in direction of vehicle forward movement. For rim and tire specifications, refer to “Technical Data”.
Warning! The spare wheel rim is for temporary use only. Use for over a total of 12 000 miles (20 000 km) (aggregate of all uses) may cause wheel rim failure leading to an accident and possible injuries. The dimensions of the spare wheel are different from those of the road wheels of the rear axle. As a result, the vehicle handling characteristics change when driving with a spare wheel mounted on the rear axle. The spare wheel should only be used temporarily, and replaced with a regular road wheel as quick as possible.
Tires, Wheels
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
261
J_C208_II.book Seite 262 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tires, Wheels
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Changing wheels
Warning! The jack is designed exclusively for jacking up the vehicle at the jack tubes built into either side of the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel change. Never get beneath the vehicle while it is supported by the jack. Keep hands and feet away from the area under the lifted vehicle. Always firmly set parking brake and block wheels before raising vehicle with jack. Do not disengage parking brake while the vehicle is raised. Be certain that the jack is always vertical when in use, especially on hills. Always try to use the jack on level surface. Be sure that the jack arm is fully inserted in the jack tube. Always lower the vehicle onto sufficient capacity jackstands before working under the vehicle.
262
Move vehicle to a level area which is a safe distance from the roadway.
1. Set parking brake and turn on hazard warning
flasher.
2. Move selector lever to position “P” and turn off
engine.
3. Prevent vehicle from rolling away by blocking wheels with wheel chocks (not supplied with vehicle) or sizable wood block or stone. When changing a wheel on a hill, place chocks on the downhill side blocking both wheels of the other axle. On a level road, place one chock in front of and one behind the wheel that is diagonally opposite to the wheel being changed.
J_C208_II.book Seite 263 Donnerstag, 31. Mai 2001 10:13 10
4. Using the wrench, loosen but do not yet remove the
wheel bolts.
5. Remove the protective cover from the jack support
tube opening by inserting the screwdriver (supplied in the tool kit) in the opening and prying it out. The tube openings are located directly behind the front wheel housings and in front of the rear wheel housings.
Tires, Wheels
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
263
J_C208_II.book Seite 264 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tires, Wheels
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
264
6. Insert jack arm fully into the tube hole up to the
stop. Place jack on firm ground. Position the jack so that it is always vertical (plumb-line) as seen from the side (see arrow), even if the vehicle is parked on an incline.
7. Jack up the vehicle until the wheel is clear of the ground. Never start engine while vehicle is raised.
8. Unscrew upper-most wheel bolt and install
alignment bolt (1) supplied in the tool kit. Remove the remaining bolts. Keep bolt threads protected from dirt and sand.
9. Remove wheel. Grip wheel from the sides. Keep
hands from beneath the wheels.
J_C208_II.book Seite 265 Donnerstag, 31. Mai 2001 10:13 10
11
10. Clean contact surfaces of wheel and wheel hub.
Install spare wheel on wheel hub. Insert wheel bolts and tighten them slightly. To avoid paint damage, place wheel flat against hub and hold it there while installing first wheel bolt. Unscrew the alignment bolt (1) to install the last wheel bolt.
11. Lower vehicle. Remove jack and insert jack tube
cover.
12. Using the wrench, tighten the five bolts evenly,
following the sequence illustrated, until all bolts are tight. Observe a tightening torque of 80 ft.lb. (110 Nm). Before storing the jack, the jack arm must be lowered almost to the base of the jack. For proper storage of vehicle jack see page 258.
13. Ensure proper tire pressure.
265
Tires, Wheels
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 266 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Tires, Wheels
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Warning! Always replace wheel bolts that are damaged or rusted. Never apply oil or grease to wheel bolts. Damaged wheel hub threads should be repaired immediately. Incorrect mounting bolts or improperly tightened mounting bolts can cause the wheel to come off. This could cause an accident. Be sure to use the correct mounting bolts.
266
Warning! The spare wheel rim is for temporary use only. Use for over a total of 12 000 miles (20 000 km) (aggregate of all uses) may cause wheel rim failure leading to an accident and possible injuries. The dimensions of the spare wheel are different from those of the road wheels of the rear axle. As a result, the vehicle handling characteristics change when driving with a spare wheel mounted on the rear axle. The spare wheel should only be used temporarily, and replaced with a regular road wheel as quick as possible.
J_C208_II.book Seite 267 Donnerstag, 31. Mai 2001 10:13 10
Tire inflation pressure A table (see fuel filler flap) lists the tire inflation pressures specified for Mercedes-Benz recommended tires as well as for the varying operating conditions.
Important! Tire pressure changes by approx. 1.5 psi (0.1 bar) per 18°F (10°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage – especially in the winter. Example: If garage temperature = approx. +68°F (+20°C) and ambient temperature = approx. +32°F (0°C) then the adjusted air pressure = specified air pressure +3 psi (+0.2 bar).
Tire pressures listed for light loads are minimum values offering high driving comfort. Increased inflation pressures for heavy loads produce favorable handling characteristics with lighter loads and are perfectly permissible. The ride of the vehicle, however, will become somewhat harder. Tire temperature and pressure increase with the vehicle speed. Tire pressure should therefore only be checked and corrected on cold tires. Correct tire pressure in warm tires only if pressure has dropped below the pressure listed in the table and the respective operating conditions are taken into consideration. An underinflated tire due to a slow leak (e.g. due to a nail in the tire) may cause damage such as tread separation, bulging etc.. Regular tire pressure checks (including the spare tire) at intervals of no more than 14 days are therefore essential.
Tires, Wheels
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
267
J_C208_II.book Seite 268 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Battery
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
If a tire constantly loses air, it should be inspected for damage. The spare tire should be checked periodically for condition and inflation. Spare tire will age and become worn over time even if never used, and thus should be inspected and replaced when necessary.
Warning! Do not overinflate tires. Overinflating tires can result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc.. Follow recommended inflation pressures. Do not overload the tires by exceeding the specified vehicle capacity weight (as indicated by the label on the driver’s door latch post). Overloading the tires can overheat them, possibly causing a blowout.
268
Battery
Warning! Failure to follow these instructions can result in severe injury or death. Never lean over batteries while connecting, you might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking etc..
Important! Battery replacement information: The maintenance-free battery is located in the trunk under the trunk floor. The service life of the battery is dependent on its condition of charge. The battery should always be kept sufficiently charged, in order to last an optimum length of time.
J_C208_II.book Seite 269 Donnerstag, 31. Mai 2001 10:13 10
Therefore, we strongly recommend that you have the battery charge checked frequently, and corrected if necessary, especially if you use the vehicle less than approximately 200 miles (300 km) per month, mostly for short distance trips, or if it is not used for long periods of time. Only charge a battery with a battery charger after the battery has been disconnected from the vehicle’s electrical circuit. Always disconnect the battery negative lead first and connect last. When removing and connecting the battery, always make sure that all electrical consumers are off and the electronic key is in steering lock position 0. The battery and its filler caps must always be securely installed when the vehicle is in operation. During removal and installation always protect the disconnected battery positive (+) terminal with the cover attached to the battery. While the engine is running the battery terminal clamps must not be loosened or detached, otherwise the generator and other electronic components would be damaged.
Note: After reconnecting the battery also set the clock (see page 108), resynchronize the front seats (see page 49), front seat head restraints (see page 49), the express feature of the power windows (see page 148), the sliding/pop-up roof (see page 150) and the electronic stability program (ESP) (see page 219).
Battery recycling Batteries contain material that can harm the environment with improper disposal. Large 12 Volt storage batteries contain lead. Recycling of batteries is the preferred method of disposal. Many states require sellers of batteries to accept old batteries for recycling.
Battery
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
269
J_C208_II.book Seite 270 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Jump starting
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Jump starting
Warning! Failure to follow these directions will cause damage to the electronic components, and can lead to a battery explosion and severe injury or death. Never lean over batteries while connecting or jump starting, you might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water, and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and very explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking etc.. Read all instructions before proceeding.
270
Important! A discharged battery can freeze at approx. +14°F (–10°C). In that case, it must be thawed out before jumper cables are used. Attempting to jump start a frozen battery can result in it exploding, causing personal injury. Jumper cable specifications: • Minimum cable cross-section of 25 mm2 or approx.
2 AWG
• Maximum length of 11.5 ft. (3.5 m). If the battery is discharged, the engine should be started with jumper cables and the (12 V) battery of another vehicle. Only use 12 V battery to jump start your vehicle. Jump starting with more powerful battery could damage the vehicle’s electrical systems, which will not be covered by the Mercedes-Benz Limited Warranty. The battery is located in the trunk under the trunk floor.
J_C208_II.book Seite 271 Donnerstag, 31. Mai 2001 10:13 10
Proceed as follows:
Important!
1. Position the vehicle with the charged battery so that
the jumper cables will reach, but never let the vehicles touch. Make sure the jumper cables do not have loose or missing insulation.
2. On both vehicles:
• Turn off engine and all lights and accessories, except hazard warning flashers or work lights. • Apply parking brake and shift selector lever to
position “P”.
Important!
3. Clamp one end of the first jumper cable to the
positive (+) under hood terminal of the discharged battery and the other end to the positive (+) terminal of the charged battery. Make sure the cable clamps do not touch any other metal parts.
4. Clamp one end of the second jumper cable to the
grounded negative (–) terminal of the charged battery and the final connection to the negative (–) terminal (2) of the discharged battery.
5. Start engine of the vehicle with the charged battery
and run at high idle. Make sure the cables are not on or near pulleys, fans, or other parts that move when the engine is started. Allow the discharged battery to charge for a few minutes. Start engine of the disabled vehicle in the usual manner.
6. After the engine has started, remove jumper cables
by exactly reversing the above installation sequence, starting with the last connection made first. When removing each clamp, make sure that it does not touch any other metal while the other end is still attached.
Notes: If engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized Mercedes-Benz Center. Excessive unburned fuel may damage the catalytic converter.
Jump starting
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
271
J_C208_II.book Seite 272 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Towing
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
272
Towing the vehicle
Warning! Prior to towing the vehicle with all wheels on the ground, make certain that the electronic key is in steering lock position 2. The maximum towing speed and distance with the vehicle on the ground is 30 mph (50 km/h) and 30 miles (50 km). If the electronic key is left in the steering lock position 0 for an extended period of time, it can no longer be turned in the lock. In this case, the steering is locked. To unlock, remove electronic key from steering lock and reinsert.
Important! When towing the vehicle, please, note the following: With the automatic central locking activated and the electronic key in steering lock position 2, the vehicle doors lock if the left front wheel as well as the right rear wheel are turning at vehicle speeds of approx. 9 mph (15 km/h) or more. To prevent the vehicle door locks from locking, deactivate the automatic central locking, see page 36.
P88.20-2027-26
The rear towing eye is located at the right, below the bumper. The front towing eye is located on the passenger side behind the grille in the bumper panel. Grille removal: Hold left and right end of grille and pull out. Grille installation: Engage left and right end of grille and press in securely.
J_C208_II.book Seite 273 Donnerstag, 31. Mai 2001 10:13 10
We recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. The vehicle may be towed with all wheels on the ground and the selector lever in position “N” for distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h). The electronic key must be in steering lock position 2. To be certain to avoid a possibility of damage to the transmission, however, we recommend the drive shaft be disconnected at the rear axle drive flange for any towing beyond a short tow to a nearby garage. Do not tow with sling-type equipment. Towing with sling-type equipment over bumpy roads will damage radiator and supports. Use wheel lift, dolly, or flat bed equipment, with electronic key in steering lock turned to position 0.
Warning! With the engine not running, there is no power assistance for the braking and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.
Note: To signal turns while being towed with hazard warning flasher in use, turn electronic key in steering lock to position 2 and activate combination switch for left or right turn signal in usual manner – only the selected turn signal will operate. Upon canceling the turn signal, the hazard warning flasher will operate again.
Caution! If the vehicle is towed with the front axle raised, the engine must be shut off (electronic key in steering lock position 0 or 1). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Switch off the tow-away alarm (see page 44) as well as the ESP (see page 220).
Towing
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
273
J_C208_II.book Seite 274 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Towing
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
274
To do so, insert a pin (1), e.g. ball point pen, into the covered opening below the position “D” of the shift pattern. While pushing the pin down, move selector lever from position “P”. After removal of the pin from the opening, the cover will not close fully. Only after moving the selector lever to positions “D+” and “D–” does the cover return to its closed position.
Transmission selector lever, manually unlocking
In the case of power failure the transmission selector lever can be manually unlocked, e.g. to tow the vehicle.
J_C208_II.book Seite 275 Donnerstag, 31. Mai 2001 10:13 10
Exterior lamps
Headlamp adjustment Correct headlamp adjustment is extremely important. Check and readjust headlamps at regular intervals and when a bulb has been replaced. For adjusting headlamp aim see page 280.
Replacing bulbs
Warning! Bulbs and bulb holder can be very hot. Allow the lamp to cool down before changing a bulb. Halogen lamps contain pressurized gas. A bulb can explode if you:
• touch or move it when hot, • drop the bulb, • scratch the bulb.
Wear eye and hand protection.
To prevent a possible electrical short circuit, switch off lamp prior to replacing a bulb. When replacing bulbs, install only 12 volt bulbs with the specified watt rating. When replacing halogen bulbs do not touch glass portion of bulb with bare hands. Use plain paper or a clean cloth.
Warning! Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its components. We recommend that you have such work done by a qualified technician.
Exterior lamps
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
275
J_C208_II.book Seite 276 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Exterior lamps
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
276
Headlamp assembly (Halogen)
Headlamp assembly (Xenon) (optional CLK 430)
P82.10-2394-26
P82.10-2395-26
1 Headlamp vertical adjustment screw 2 Cover for low beam headlamp 3 Cover for high beam headlamp, parking and
standing lamp
4 Bulb socket for turn signal lamp 5 Electrical connector for low beam headlamp bulb 6 Electrical connector for high beam headlamp bulb 7 Bulb socket for parking and standing lamp
J_C208_II.book Seite 277 Donnerstag, 31. Mai 2001 10:13 10
Bulbs for low or high Beam H7 (55 W) Open hood. Rotate cover (2 or 3) counterclockwise and remove. Pull off electrical connector (5 or 6). Unhook clamping ring and remove bulb. Insert new bulb (seating properly in cutouts of bulb socket), mount clamping ring. Reinstall and push electrical connector on securely. Reinstall cover (2 or 3).
Xenon (optional) Bulb for low beam
Warning! Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its components. We recommend that you have such work done by a qualified technician.
Turn signal lamp 1156 NA (26.9/5 W/32/4 cp bulb) Open hood. Twist bulb socket (4) counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket. Reinstall lamp assembly until properly seated.
Parking and standing lamp H 6W (6 W bulb) Open hood. Rotate cover (3) counterclockwise and remove. Twist bulb socket (7) counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket. Reinstall lamp assembly until properly seated. Reinstall cover (3).
Exterior lamps
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
277
J_C208_II.book Seite 278 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Exterior lamps
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
278
Taillamp assemblies
P82.10-2080-26
P82.10-2083-26
Open trunk lid. Swing cover aside (bulbs 1, 2 and 3).
1 Turn signal lamp (21 W/24 cp bulb) 2 Stop, tail, parking, and side marker lamp
(21/4 W bulb)
3 Tail and parking lamp (5 W/4 cp bulb)
4 Driver’s side:
Rear fog lamp (21 W/32 cp bulb) 5 Backup lamp (21 W/32 cp bulb)
Twist bulb socket counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket. Close cover (bulbs 1, 2 and 3).
J_C208_II.book Seite 279 Donnerstag, 31. Mai 2001 10:13 10
Side marker lamp, front (5 W/4 cp bulb)
Carefully slide lamp towards front (arrow), and remove back and first. Twist bulb socket counterclockwise and pull out. Push bulb socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket, push in and twist clockwise. To reinstall lamp, set front end of lamp in bumper and let back end snap into place.
Exterior lamps
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
279
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 280 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Exterior lamps
High mounted stop lamp, Additional turn signals on the exterior mirror The high mounted stop lamp (3rd brake lamp), and the additional turn signals on the exterior mirrors are equipped with LEDs. Have the system checked at an authorized Mercedes-Benz Center if a fault or defect occurs.
280
Adjusting headlamp aim Correct headlamp adjustment is extremely important. To check and readjust a headlamp, follow steps 1 through 5. Please note: • Low beam adjustments simultaneously aim the high
beam.
• Vehicle should have a normal trunk load.
1. Park vehicle on level surface approximately 25 ft. (7.6 m) from a vertical test screen or wall. The centerline of the vehicle must be at a 90° angle to the test screen.
J_C208_II.book Seite 281 Donnerstag, 31. Mai 2001 10:13 10
10
N82.10-2396-26
2. (Low beams on):
3. (Low beams off):
Using a carpenter’s level, align and mark a vertical centerline (8) on the test screen using the vertex of the angle formed in each beam image. As a check, the distance between centerlines should be 49 1/4 inches (1250 mm). If the distance does not check, have the system verified at an authorized Mercedes-Benz Center.
Measure the vertical height from the floor to reference point (10) on high beam lens. Subtract approx. 2 inches (53 mm) from measurement, and mark a horizontal centerline (9) on the test screen at the resulting height from the floor. It must be at a 90° angle to the vertical centerline.
4. Open hood.
Exterior lamps
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
281
J_C208_II.book Seite 282 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Exterior lamps
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
282
5. Vertical headlamp aim (low beams on):
Turn adjusting screw (1) (counterclockwise to adjust headlamp downward, clockwise upward) until the headlamps illuminate the test screen as shown. The vertex of the angle formed in each beam image should align with the vertical and horizontal centerlines (8 and 9). The left and right headlamps must be adjusted individually.
Note: If it is not possible to obtain a proper headlamp adjustment, have the system checked at your authorized Mercedes-Benz Center.
J_C208_II.book Seite 283 Donnerstag, 31. Mai 2001 10:13 10
Changing batteries in the electronic key
P80.20-2201-26
P80.35-2029-26
1 Transmit buttons 2 Lamp for battery check and function control
Changing batteries Move locking tab (3) in direction of right arrow and remove mechanical key (4, left arrow).
Checking batteries If one of the transmit buttons (1) is pressed, the battery check lamp (2) lights up briefly – indicating that the batteries are in order. Change batteries if the battery check lamp (2) does not light up briefly.
Electronic key
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
283
J_C208_II.book Seite 284 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Electronic key
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
284
P80.35-2025-26
Insert mechanical key (4) in side opening (5) to open latch. Press briefly (do not use mechanical key as lever) to release battery compartment. Remove mechanical key from side opening. Carefully remove battery compartment in direction of arrow (6).
P80.35-2027-26
Change batteries (7), inserting new ones under contact spring (8) with plus (+) side facing up. Return battery compartment into housing until locked in place and slide mechanical key back into electronic key.
J_C208_II.book Seite 285 Donnerstag, 31. Mai 2001 10:13 10
Important! Batteries contain materials that can harm the environment if disposed of improperly. Recycling of batteries is the preferred method of disposal. For disposal, please follow manufacturer’s recommendation on battery package. Replacement Battery: Lithium, type CR 2025 or equivalent.
Synchronizing remote control The remote control may have to be resynchronized, if the vehicle cannot be locked or unlocked. To synchronize insert electronic key in steering lock. The remote control should once again be operational.
Electronic key
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
285
J_C208_II.book Seite 286 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Emergency operation of sliding/pop-up roof
286
Emergency operation of sliding/pop-up roof
The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur. The sliding/pop-up roof drive is located behind the lens of the left interior lamp between the sun visors.
To slide the roof closed or to raise the roof at the rear: turn crank clockwise. To slide the roof open or to lower the roof at the rear: turn crank counterclockwise.
1. Pry off lens (1) by using a screw driver. 2. Remove cover (2). 3. Obtain crank (3) (supplied with vehicle) and insert
it through hole.
Note: Push crank upward while turning it, to disengage the electric motor.
J_C208_II.book Seite 287 Donnerstag, 31. Mai 2001 10:13 10
Manual release for fuel filler flap
The manual release knob is located behind the right side trunk panel. In case the central locking system does not release the fuel filler flap, pull the manual release knob while simultaneously opening the fuel filler flap.
Replacing wiper blade insert For safety reasons, remove electronic key from steering lock before replacing the wiper blade, otherwise the motor can suddenly turn on and cause injury.
Notes: Do not open engine hood with wiper arm folded forward. Do not allow the wiper arm to contact the windshield glass without a wiper blade inserted. The glass may be scratched or broken. Make certain that the wiper blade is properly installed. An improperly installed wiper blade may cause windshield damage.
Manual release for fuel filler flap
287
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 288 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Replacing wiper blade insert
288
P82.30-0333-26
Removal: Fold wiper arm forward. Press safety tab down (1), push wiper blade downward (2) and remove. Place wiper blade on firm support. Press down both tabs and slide (direction of arrow) the wiper blade insert out of the retainer claws.
Installation: Slide (direction of arrow) wiper blade insert into retainer claws until tabs are engaged. Insert wiper blade between tabs (3) on the wiper arm, and slide into end of wiper arm. Press safety tab upward until it locks in place.
J_C208_II.book Seite 289 Donnerstag, 31. Mai 2001 10:13 10
Roof rack
Use only those roof racks approved by Mercedes-Benz to avoid damage to the vehicle. Follow manufacturer’s installation instructions. Mount supports only between markings which are visible on the rubber molding.
Note: Please observe that roof rack does not interfere with the operation of the sliding/pop-up sunroof and that there is sufficient clearance between the roof rack and the trunk lid in the full open position.
Roof rack
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
289
J_C208_II.book Seite 290 Donnerstag, 31. Mai 2001 10:13 10
J_C208_II.book Seite 291 Donnerstag, 31. Mai 2001 10:13 10
Vehicle care
Cleaning and care
of the vehicle .............................292
Power washer ..............................293
Tar stains .....................................293
Paintwork, painted body components .................................293
Engine cleaning ..........................294
Vehicle washing .........................294
Ornamental moldings ................294
Headlamps, taillamps, turn signal lenses ......................294Window cleaning ....................... 295
Wiper blade ................................ 295
Light alloy wheels ..................... 295
Instrument cluster ..................... 295
Steering wheel and gear selector lever ..................... 295
Cup holder .................................. 296
Seat belts ..................................... 296
Hard plastic trim items ............. 296
Headliner and shelf below rear window .................... 296
Upholstery .................................. 296
Plastic and rubber parts ........... 296Contents – Vehicle care
291
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 292 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Cleaning and care of the vehicle
292
Cleaning and care of the vehicle
Warning! Many cleaning products can be hazardous. Some are poisonous, others are flammable. Always follow the instructions on the particular container. Always open your vehicle’s doors or windows when cleaning the inside. Never use fluids or solvents that are not designed for cleaning your vehicle.
In operation, your vehicle is subjected to varying external influences which, if gone unchecked, can attack the paintwork as well as the underbody and cause lasting damage. Such damage is caused not only by extreme and varying climatic conditions, but also by air polution, road salt, tar, gravel and stone chipping. Grease and oil, fuel, coolant, brake fluid, bird droppings, insects, tree resins etc. should be removed immediately to avoid paint damage. Frequent washing reduces and/or eliminates the aggressiveness and potency of the above adverse influences.
More frequent washings are necessary to deal with unfavorable conditions; for example, near the ocean, in industrial areas (smoke, exhaust emissions), or during winter operation. You should check your vehicle from time to time for stone chipping or other damage. Any damage should be repaired as soon as possible to prevent the start of corrosion. In doing so, do not neglect the underside of the vehicle. A prerequisite for a thorough check is a washing of the underbody followed by a thorough inspection. Damaged areas need to be reundercoated. Your vehicle has been treated at the factory with a wax- base rustproofing in the body cavities which will last for the lifetime of the vehicle. Post-production treatment is neither necessary nor recommended by Mercedes-Benz because of the possibility of incompatibility between materials used in the production process and others applied later. We have selected car-care products and compiled recommendations which are specially matched to our vehicles and which always reflect the latest technology. You can obtain Mercedes-Benz approved car-care products at your authorized Mercedes-Benz Center.
J_C208_II.book Seite 293 Donnerstag, 31. Mai 2001 10:13 10
Scratches, corrosive deposits, corrosion or damage due to negligent or incorrect care cannot always be removed or repaired with the car-care products recommended here. In such cases it is best to seek aid at your authorized Mercedes-Benz Center. The following topics deal with the cleaning and care of your vehicle and give important “how-to” information as well as references to Mercedes-Benz approved car-care products. Additional information can be found in the booklet titled “Vehicle Care Guide”.
Power washer When using a power washer for cleaning the vehicle always observe manufacturer’s operating instructions.
Caution! Never use a round nozzle to power wash tires. The intense jet of water can result in damage to the tire. Always replace a damaged tire. Always keep the jet of water moving across the surface. Do not aim directly at electrical parts, electrical connectors, seals, or other rubber parts.
Tar stains Quickly remove tar stains before they dry and become more difficult to remove. A tar remover is recommended.
Paintwork, painted body components Mercedes-Benz approved Paint Care should be applied when water drops on the paint surface do not “bead up”, normally in 3 to 5 months, depending on climate and washing detergent used. Mercedes-Benz approved Paint Cleaner should be applied if paint surface shows signs of dirt embedding (i.e. loss of gloss). Do not apply any of these products or wax if your vehicle is parked in the sun or if the hood is still hot. Use the appropriate MB-Touch-Up Stick for quick and provisional repairs of minor paint damage (i.e. chips from stones, vehicle doors etc.).
Cleaning and care of the vehicle
293
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 294 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Cleaning and care of the vehicle
294
Engine cleaning Prior to cleaning the engine compartment make sure to protect electrical components and connectors from the intrusion of water and cleaning agents. Corrosion protection, such as MB Anticorrosion Wax should be applied to the engine compartment after every engine cleaning. Before applying, all control linkage bushings and joints should be lubricated. The poly-V-belt and all pulleys should be protected from any wax.
Vehicle washing Do not use hot water or wash your vehicle in direct sunlight. Use only a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo. Thoroughly spray the vehicle with a diffused jet of water. Direct only a very weak spray towards the ventilation intake. Use plenty of water and rinse the sponge and chamois frequently. Rinse with clear water and thoroughly wipe dry with a chamois. Do not allow cleaning agents to dry on the finish.
In the winter, thoroughly remove all traces of road salt as soon as possible. When washing the underbody, do not forget to clean the inner sides of the wheels.
Ornamental moldings For regular cleaning and care of very dirty chrome- plated parts, use a chrome cleaner.
Headlamps, taillamps, turn signal lenses Use a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo, with plenty of water. To prevent scratches, never apply strong force and use only a soft, non-scratchy cloth when cleaning the lenses. Do not attempt to wipe dirty lenses with a dry cloth or sponge.
J_C208_II.book Seite 295 Donnerstag, 31. Mai 2001 10:13 10
Window cleaning Use a window cleaning solution on all glass surfaces. An automotive glass cleaner is recommended.
Note: For safety reasons, switch off wiper and remove electronic key from steering lock before cleaning the windshield, otherwise the wiper motor can suddenly turn on and cause injury.
Wiper blade Clean the wiper blade rubber with a clean cloth and detergent solution.
Note: For safety reasons, remove electronic key from steering lock before cleaning the wiper blade, otherwise the wiper motor can suddenly turn on and cause injury.
Light alloy wheels Mercedes-Benz approved Wheel Care should be used for regular cleaning of the light alloy wheels. If possible, clean wheels once a week with Mercedes-Benz approved Wheel Care, using a soft bristle brush and a strong spray of water. Follow instructions on container.
Note: Use only acid-free cleaning materials. The acid could lead to corrosion.
Instrument cluster Use a gentle dishwashing detergent or mild detergent for delicate fabrics as a washing solution. Wipe with a cloth moistened in lukewarm solution. Do not use scouring agents.
Steering wheel and gear selector lever Wipe with a damp cloth and dry thoroughly or clean with Mercedes-Benz approved Leather Care.
Cleaning and care of the vehicle
295
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 296 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Cleaning and care of the vehicle
296
Cup holder Use a gentle dishwashing detergent or mild detergent for delicate fabrics as a washing solution. Wipe with a cloth moistened in lukewarm solution. Do not use scouring agents.
Seat belts The webbing must not be treated with chemical cleaning agents. Use only clear, lukewarm water and soap. Do not dry the webbing at temperatures above 176°F (80°C) or in direct sunlight.
Warning! Do not bleach or dye seat belts as this may severely weaken them. In a crash they may not be able to provide adequate protection.
Hard plastic trim items Pour Mercedes-Benz approved Interior Care onto soft lint-free cloth and apply with light pressure.
Headliner and shelf below rear window Clean with soft bristle brush, or use a dry-shampoo cleaner in case of excessive dirt.
Upholstery Using aftermarket seat covers or wearing clothing that have the tendency to give off coloring (e.g. when wet etc.) may cause the upholstery to become permanently discolored. By lining the seats with a proper intermediate cover, contact-discoloration will be prevented. Leather Upholstery Wipe leather upholstery with a damp cloth and dry thoroughly or clean with Mercedes-Benz approved Leather Care. Exercise particular care when cleaning perforated leather as its underside should not become wet. MB Tex Upholstery Pour Mercedes-Benz approved Interior Care onto soft lint-free cloth and apply with light pressure.
Plastic and rubber parts Do not use oil or wax on these parts.
J_C208_II.book Seite 297 Donnerstag, 31. Mai 2001 10:13 10
Technical data
Spare parts service ........................298
Warranty coverage .........................298
Identification labels .......................299
Layout of poly-V-belt drive ............300
Technical data ................................301
Fuels, coolants, lubricants etc. –capacities ...................................305
Engine oils ...................................... 307
Engine oil additives ...................... 307
Air conditioner refrigerant .......... 307
Brake fluid ...................................... 307
Premium unleaded gasoline ........ 308
Fuel requirements ........................ 308
Gasoline additives ......................... 309
Coolants .......................................... 309
Consumer information .................. 311Contents – Technical data
297
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 298 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Technical data
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Spare parts service All authorized Mercedes-Benz Centers maintain a stock of original spare parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different spare parts, for other Mercedes-Benz models, are available. Mercedes-Benz original spare parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Mercedes-Benz original spare parts should be installed.
Important! The use of non-genuine parts and accessories not authorized by Mercedes-Benz could damage the vehicle or compromise its durability or safety.
298
Warranty coverage Your vehicle is covered under the terms of the “warranties” printed in the Service and Warranty Information booklet and your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed on the vehicle in accordance with the terms of the following warranties:
1. New vehicle limited warranty 2. Emission system warranty 3. Emission performance warranty 4. California, Massachusetts, and Vermont emission
control systems warranty
Replacement parts and accessories are covered by the Mercedes-Benz Spare Parts and Accessories warranties, copies of which are available at any Mercedes-Benz Center.
Loss of Service and Warranty Information Booklet Should you lose your Service and Warranty Information booklet, have your authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.
J_C208_II.book Seite 299 Donnerstag, 31. Mai 2001 10:13 10
Identification labels
XXXXXXXXX
1 Certification label
2 Vehicle Identification Number (VIN)
When ordering spare parts, please specify vehicle identification and engine numbers.
Technical data
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
299
J_C208_II.book Seite 300 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Technical data
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
300
Layout of poly-V-belt drive
