if the vehicle is involved in an accident. Switching off: X Press hazard warning flasher switch
(Y page 278).
or X Press switch ~. or X Unlock the vehicle with the SmartKey.
2009-05-15T11:47:50+02:00 - Seite 280
Version: 2.11.8.1
Wipers Notes ! Do not operate the wipers when the
windshield is dry. Dust that accumulates on a windshield might scratch the glass and/ or damage the wiper blades when wiping occurs on a dry windshield. If it is necessary to operate the wipers in dry weather conditions, always operate the wipers with washer fluid.
! If the windshield wipers leave smears on the windshield after the car has been driven through an automatic car wash, then wax or other residue is on the windshield. Shortly after washing the car in an automatic car wash, clean the windshield with washer fluid.
Windshield wipers X Observe notes on page (Y page 280).
Switching on/off
Combination switch
1 $ Windshield wipers off
2 Ä Slow intermittent wiping31
3 Å Fast intermittent wiping32
4 ° Slow continuous wiping
31 Rain sensor operation with low sensitivity. 32 Rain sensor operation with high sensitivity.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 281
Version: 2.11.8.1
5 ¯ Fast continuous wiping B í Single wipe/ î Wiping with
washer fluid
X Switch on the ignition. X Turn the combination switch to the desired position, depending on the intensity of the rain.
i When the windshield wipers are switched
on and you stop the vehicle, the wipers operate more slowly.
Intermittent wiping Only switch on intermittent wiping under wet weather conditions or in the presence of precipitation. When you select intermittent wiping, the rain sensor is activated. The rain sensor sets a suitable wiping interval depending on the wetness of the sensor surface automatically. ! Do not leave windshield wipers on an intermittent setting when the vehicle is taken to an automatic car wash or during windshield cleaning. Windshield wipers will operate in the presence of water sprayed on the windshield, and windshield wipers may be damaged as a result.
! If you have set intermittent wiping, dirt on
the surface of the rain sensor or optical effects may cause the windshield wipers to wipe in an undesired fashion. This could then damage the windshield wiper blades or scratch the windshield. You should therefore switch off the windshield wipers when weather conditions are dry.
X Turn the combination switch to position
Ä or Å. After the initial wipe, pauses between wipes are controlled by the rain sensor automatically.
Intermittent wiping is interrupted when the vehicle is at a standstill and a door is opened. This protects persons getting into or out of the vehicle from being sprayed.
Wipers
281
Intermittent wiping will be continued when all doors are closed and Rthe automatic transmission is in drive
position D or reverse gear R or
Rthe wiper setting is changed using the
combination switch
Single wipe X Press the combination switch briefly in direction of arrow B to the resistance point. The windshield wipers wipe one time without washer fluid.
Wiping with washer fluid X Press the combination switch in direction
of arrow B past the resistance point. The windshield wipers operate with washer fluid.
i To prevent smears on the windshield or noisy/chattering wiper blades, wipe with washer fluid every now and then even when it is raining.
For information on filling up the washer reservoir, see “Washer system and headlamp cleaning system” (Y page 372). For information on cleaning the headlamps with washer fluid, see “Headlamp cleaning system” (Y page 278).
Problems with wipers ! If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediately. For safety reasons, do the following before attempting to remove any blockage: RStop the vehicle in a safe location. RRemove the SmartKey from the starter
switch. or
2009-05-15T11:47:50+02:00 - Seite 282
Version: 2.11.8.1
The windows operate differently when the switch is pulled and held. See the “Closing when a window is blocked” section in this chapter for details. The closing of the door windows can be immediately halted by releasing the switch or, if the switch was pulled past the resistance point and released, by either pressing or pulling the respective switch. The closing of the rear side windows can be immediately halted by releasing the switch. Activate the override switch when children are riding in the back seats of the vehicle. The children may otherwise injure themselves, e.g. by becoming trapped in the window opening. G Warning! Do not keep any part of your body up against the window pane when opening a window. The downward motion of the pane may pull that part of your body down between the window pane and the door frame and trap it there. If there is a risk of entrapment, release the switch and pull it to close the window.
i You can also open or close the windows using the SmartKey, see “Summer opening feature” (Y page 283) and “Convenience closing feature” (Y page 284).
i After switching off the ignition or
removing the SmartKey from the starter switch, you can operate the windows until you open a door. If no door was opened you can operate the windows for up to 5 minutes.
216_AKB; 3; 90, en-US d2ureepe,
282 Power windows
RTurn off the engine by pressing the KEYLESS-GO start/stop button and open the driver’s door (with the driver’s door open, starter switch is in position 0, same as with SmartKey removed from starter switch).
REngage the parking brake. RRemove blockage. RTurn the windshield wipers on again. If the windshield wipers fail to function at all with the combination switch in position Ä or Å, Rset the combination switch to the next
higher wiper speed
Rhave the windshield wipers checked at the nearest authorized Mercedes-Benz Center
Power windows Opening and closing The windows are opened and closed electrically. The switches for all windows are located on the driver’s door. The switches for the respective windows are located on the passenger door and the rear side trim panels. i Operating the rear side windows from the rear is not possible when you activate the override switch (Y page 55). G Observe Safety notes, see page 51. G Warning! When opening or closing the windows, make sure there is no danger of anyone being harmed by the opening/closing procedure. The door windows are equipped with the express operation and automatic reversal function. If in express operation mode a door window encounters an obstruction that blocks its path, the automatic reversal function will stop the door window and open it slightly.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 283
Version: 2.11.8.1
Power windows
283
If the window is blocked again and opens slightly: X Immediately after the window was blocked, pull and hold the respective switch upward until the window is fully closed. The window closes without automatic reversal function. G Warning! Pulling and holding the switch to close the window immediately after it had been blocked two times will cause the window to close without any reversal function for as long as you hold the switch.
Synchronizing power windows The windows must be synchronized if they cannot be fully closed. Each window must be synchronized separately. X Close all doors. X Switch on the ignition. X Pull and hold switch :, ;, = or ?
(Y page 283) until the respective window is closed. The window opens again slightly.
X Pull and hold the respective switch once
more immediately until the window is closed completely.
X Hold the respective switch for
approximately 1 second. The window is synchronized.
Summer opening feature When the weather is warm, you can ventilate the vehicle before driving off by simultaneously Ropening the windows Ropening the tilt/sliding sunroof Rswitching on the seat ventilation for the
driver’s seat
X Switch on the ignition. X Opening/closing: Press or pull and hold switch : to ? to the resistance point. The corresponding window moves downward or upward until you release the switch.
X Express operation: Press or pull
switch : or ; past the resistance point and release. The corresponding door window opens or closes completely.
X Express opening of rear side windows: Press switch = or ? past the resistance point and release. The corresponding rear side window opens completely.
X Stopping during express operation:
Press or pull the respective switch again.
Closing when a window is blocked G Warning! Make sure that nobody can become trapped and be seriously or even fatally injured when closing a window with greater force or without automatic reversal function.
If the upward movement of a window is blocked during the closing procedure, the window will stop and open slightly. X Immediately after the window has stopped because it was blocked, pull and hold the respective switch upward until the window is fully closed. The window closes with greater force.
216_AKB; 3; 90, en-US d2ureepe,
284 Power windows
2009-05-15T11:47:50+02:00 - Seite 284
Version: 2.11.8.1
The summer opening feature can only be activated via the remote control of the SmartKey. The SmartKey must be in close proximity to the driver’s outside door handle. X Aim the transmitter eye of the SmartKey at
the driver’s outside door handle.
X Press and hold button % on the
SmartKey until the windows and the tilt/ sliding sunroof have reached the desired position. The vehicle unlocks.
X Release button % on the SmartKey to
interrupt the opening procedure.
With SmartKey The SmartKey must be in close proximity to the driver’s outside door handle. X Aim transmitter eye of the SmartKey at the
driver’s outside door handle.
X Press and hold button & on the
SmartKey until the windows and the tilt/ sliding sunroof are closed completely. The vehicle locks.
X Release button & on the SmartKey to
interrupt the closing procedure.
With KEYLESS-GO
Convenience closing feature When locking the vehicle, you can simultaneously close the windows and the tilt/sliding sunroof. G Warning! When closing the windows and the tilt/sliding sunroof, make sure there is no danger of anyone being harmed by the closing procedure. If potential danger exists, proceed as follows: RRelease button & to stop the closing
procedure. To open, press and hold button %. To continue the closing procedure after making sure that there is no danger of anyone being harmed by the closing procedure, press and hold button &.
Vehicles with KEYLESS-GO: RRelease the sensor surface on the outside door handle to stop the closing procedure. RImmediately pull on the same outside door
handle and hold firmly. The windows and the tilt/sliding sunroof will open for as long as the door handle is held but the door not opened.
The SmartKey with KEYLESS-GO must be located outside the vehicle within approximately 3 ft (1 m) of a door. X Close all doors. X Touch and hold sensor surface : on an
outside door handle until the windows and the tilt/sliding sunroof are closed completely.
i Make sure you are only touching sensor
surface :.
X Release sensor surface : to interrupt the
closing procedure.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 285
Version: 2.11.8.1
Driving and parking Safety notes G Warning! Make sure absolutely no objects are obstructing the pedals’ range of movement. Keep the driver’s footwell clear of all obstacles. If there are any floormats or carpets in the footwell, make sure the pedals still have sufficient clearance. During sudden driving or braking maneuvers the objects could get caught between or under the pedals. You could then no longer brake or accelerate. This could lead to accidents and injury. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.
Starting the engine G Warning! Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death. Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one window fully open at all times.
Driving and parking 285
Automatic transmission
Gearshift pattern for automatic transmission : Button for selecting park position P j Park position k Reverse gear i Neutral position h Drive position For more information on how to operate the gear selector lever, see “Automatic transmission” (Y page 291). X Make sure the automatic transmission is in
park position P. The transmission position indicator in the multifunction display should be on P (Y page 294).
With SmartKey X Do not depress the accelerator pedal. X Turn the SmartKey in the starter switch to
position 3 (Y page 262) and release it. The engine starts automatically.
With KEYLESS-GO G Warning! As long as the SmartKey is in your vehicle, the vehicle can be started. Therefore, never leave children unattended in the vehicle, as they could otherwise accidentally start the engine. When leaving the vehicle, always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle,
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 286
Version: 2.11.8.1
286 Driving and parking
or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could result in an accident and/or serious personal injury. You can start your vehicle without the SmartKey in the starter switch using the KEYLESS-GO start/stop button. The SmartKey must be located in the vehicle.
KEYLESS-GO start/stop button : USA only ; Canada only X Make sure the KEYLESS-GO start/stop button is inserted in the starter switch (Y page 262).
i To start the engine with the SmartKey
instead of the KEYLESS-GO function, remove the KEYLESS-GO start/stop button from the starter switch. Proceed as described in “With SmartKey” (Y page 285).
X Depress the brake pedal during the starting
procedure.
X Do not depress the accelerator pedal. X Press the KEYLESS-GO start/stop button
once. The engine starts automatically.
Starting difficulties ! Remember that extended starting
attempts can drain the battery.
The engine does not start. You can hear the starter. There could be a malfunction in the engine electronics or in the fuel supply system. Carry out the following steps: X If you are starting the engine with the
SmartKey: Turn the SmartKey in the starter switch to position 0 and repeat the starting procedure.
X If you are starting the engine with KEYLESS- GO: Close any doors that may be open to allow for better detection of the SmartKey.
or X Remove the KEYLESS-GO start/stop
button from the starter switch.
X Start the engine with the SmartKey as radio
signals from another source may be interfering with the KEYLESS-GO function.
X Repeat the starting procedure. If the engine does not start after several starting attempts: X Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
The engine does not start. You cannot hear the starter. The battery may not be charged sufficiently. X Get a jump start (Y page 471). If the engine will not start despite a jump start: X Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
The starter has been exposed to excessive temperatures. X Let the starter cool for about 2 minutes. X Repeat the starting procedure. If the engine does not start after several starting attempts: X Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 287
Version: 2.11.8.1
Driving off G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.
! Do not run a cold engine at high engine
speeds. Running a cold engine at high engine speeds may shorten the service life of the engine. This is not covered by the Mercedes-Benz Limited Warranty. CL 63 AMG: At engine temperatures below 68‡ (20†), the engine’s maximum speed is restricted in order to protect it from damage. Avoid driving your vehicle at full speed when the engine is cold to prevent premature engine wear and/or diminished comfort.
! You have forgotten to release the
electronic parking brake when driving off if Ran acoustic warning sounds Rthe message Please Release Parking Brake appears in the multifunction display
Rthe red indicator lamp for the electronic parking brake F (USA only) or ! (Canada only) in the instrument cluster flashes
Release the electronic parking brake.
! Avoid spinning of a drive wheel. This may
cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.
! Simultaneously depressing the
accelerator pedal and applying the brakes reduces engine performance and causes premature brake and drivetrain wear which is not covered by the Mercedes-Benz Limited Warranty.
Driving and parking 287
i Once the vehicle is in motion, the doors
and the trunk look automatically. The locking knobs in the doors move down. The automatic door lock feature can be deactivated (Y page 193).
Automatic transmission G Warning! It is dangerous to shift the automatic transmission out of park position P or neutral position N if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
! Only shift the automatic transmission into reverse gear R or park position P when the vehicle is stopped. Otherwise the automatic transmission could be damaged.
X Depress the brake pedal.
The gear selector lever can now be used. X Shift the automatic transmission into drive
position D or reverse gear R.
i Shifting the automatic transmission out of
park position P is only possible with the brake pedal depressed. Without the brake pedal depressed, the gear selector lever can be moved up or down. However, the parking pawl remains engaged, not allowing shifting to occur.
X Wait for the gear selection process to complete before setting the vehicle in motion.
X Release the brake pedal. X Carefully depress the accelerator pedal.
The electronic parking brake releases automatically.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 288
Version: 2.11.8.1
288 Driving and parking
The red indicator lamp F (USA only) or ! (Canada only) in the instrument cluster goes out.
After a cold start, the automatic transmission shifts at a higher engine speed. This allows the catalytic converter to reach its operating temperature earlier. For more information on driving, see “Driving instructions” (Y page 397).
If the extent of the damage cannot be determined: X Contact an authorized Mercedes-Benz
Center or call Roadside Assistance. If no damage on major assemblies, fuel system, and engine mount can be determined: X Start the engine in the usual manner.
Problems while driving The engine runs erratically and misfires RAn ignition cable may be damaged. RThe engine electronics may not be
operating properly.
RUnburned gasoline may have entered the
catalytic converter and damaged it.
X Give very little gas. X Have the problem checked at an authorized Mercedes-Benz Center as soon as possible.
The coolant temperature is above 248‡ (120†) The coolant is too hot and is no longer cooling the engine. X Stop the vehicle in a safe location as soon
as possible.
X Turn off the engine immediately. X Allow the engine and coolant to cool off. X Check the coolant level and add coolant if
necessary (Y page 372).
In case of accident If the vehicle is leaking fuel: X Do not start the engine under any
circumstances.
X Exit the vehicle at a safe distance from the
roadway.
X Notify local fire and/or police authorities.
Parking G Warning! Do not park in areas where the hot exhaust system could come into contact with combustible materials. Combustible materials such as grass, hay or leaves could be ignited and cause a vehicle fire. Unintended vehicle movement could cause serious personal injury or damage to the vehicle or the vehicle drivetrain. To reduce such risks, always do the following before turning off the engine and leaving the vehicle: RKeep right foot on the brake pedal. REngage the electronic parking brake. RShift the automatic transmission into park
position P.
RSlowly release the brake pedal. RWhen parked on an incline, always turn the
front wheels towards the road curb.
RTurn the SmartKey in the starter switch to position 0 and remove the SmartKey from the starter switch, or press the KEYLESS- GO start/stop button.
RTake the SmartKey with you and lock the
vehicle when leaving.
Electronic parking brake G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch, take it with you, and lock the vehicle. Do not leave
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 289
Version: 2.11.8.1
children unattended in the vehicle, or with access to an unlocked vehicle. Children could release the electronic parking brake and/or shift the automatic transmission out of park position P, either of which could result in an accident and/or serious personal injury.
Releasing electronic parking brake manually X Switch on the ignition. X Pull handle :.
The red indicator lamp F (USA only) or ! (Canada only) in the instrument cluster goes out.
Releasing electronic parking brake automatically The electronic parking brake releases automatically when all of the following conditions are fulfilled: RThe engine is running. RThe automatic transmission is in drive position D or reverse gear R. With the automatic transmission in reverse gear R the trunk lid must be closed.
RThe hood is closed. RYou have fastened your seat belt. RYou depress on the accelerator pedal.
Driving and parking 289
i If you have not fastened your seat belt, the following conditions must be met in order for the electronic parking brake to release automatically: RThe driver’s door is closed and you shift the automatic transmission out of park position P. or
RThe driver’s door is closed and you drive
faster than 2 mph (3 km/h).
Engaging electronic parking brake manually X Press handle :.
The red indicator lamp F (USA only) or ! (Canada only) in the instrument cluster comes on.
i You can engage the electronic parking
brake even when the SmartKey is removed from the starter switch.
Engaging electronic parking brake automatically The electronic parking brake engages automatically when the HOLD function (Y page 316) or DISTRONIC PLUS (Y page 304) brings your vehicle to a standstill. In addition, at least one of the following conditions must be met: RThe engine is turned off. RThe driver’s door is opened and the seat
belt is not inserted in the seat belt buckle.
RThe hood lock is released. RThe trunk lid is opened while the automatic
transmission is in reverse gear R.
RThe vehicle is stationary for an extended
period of time.
The red indicator lamp F (USA only) or ! (Canada only) in the instrument cluster comes on. i In addition to engaging the electronic
parking brake, the automatic transmission may shift into park position P automatically.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 290
Version: 2.11.8.1
290 Driving and parking
Emergency braking with electronic parking brake In an emergency situation, you can also brake your vehicle by using the electronic parking brake. X While driving, press handle :.
All four wheels of the vehicle will be braked for as long as you press and hold the handle for the electronic parking brake. The longer you keep the handle pressed, the stronger your vehicle will be braked. During the braking procedure Ran acoustic warning sounds Rthe message Please Release Parking Brake appears in the multifunction display Rthe red indicator lamp for the electronic parking brake F (USA only) or ! (Canada only) in the instrument cluster flashes
Once the vehicle comes to a complete stop, the electronic parking brake will engage automatically.
Turning off the engine G Warning! Do not turn off the engine before the vehicle has come to a complete stop. With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.
i If the engine cannot be turned off as
described, see “Emergency engine shutdown” (Y page 478).
X Shift the automatic transmission into park
position P.
i Observe instructions if you want the automatic transmission to remain in
neutral position N, see “Remaining in neutral position N” (Y page 292).
With SmartKey X Turn the SmartKey in the starter switch to
position 0.
X Remove the SmartKey from the starter
switch.
When you turn off the engine using the SmartKey, and remove the SmartKey from the starter switch or open a front door, the automatic transmission will shift into park position P automatically. G Warning! Keep in mind that turning off the engine alone only will shift the automatic transmission into neutral position N automatically. Always shift the automatic transmission into park position P before turning off the engine. Otherwise the vehicle could roll away which could result in an accident and/or serious personal injury.
With KEYLESS-GO X Press the KEYLESS-GO start/stop button. With the driver’s door closed, the starter switch is now in position 1. With the driver’s door opened, the starter switch is set to position 0, same as the SmartKey removed from the starter switch (Y page 262). When you turn off the engine using the KEYLESS-GO start/stop button and open a front door, the automatic transmission will shift into park position P automatically. G Warning! Keep in mind that turning off the engine alone only will shift the automatic transmission into neutral position N automatically. Always shift the automatic transmission into park position P before turning off the engine.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 291
Version: 2.11.8.1
Automatic transmission 291
Otherwise the vehicle could roll away which could result in an accident and/or serious personal injury.
i In an emergency you can turn off the
engine while driving by pressing and holding the KEYLESS-GO start/stop button for approximately 3 seconds.
If you have started the engine with the KEYLESS-GO start/stop button and cannot turn it off as described above: X Remove the KEYLESS-GO start/stop
button from the starter switch.
X Insert the SmartKey into the starter switch. The engine turns off. The starter switch is in position 0 (Y page 262).
Automatic transmission Introduction For information on driving with an automatic transmission, see “Driving and parking” (Y page 285). G Warning! Make sure absolutely no objects are obstructing the pedals’ range of movement. Keep the driver’s footwell clear of all obstacles. If there are any floormats or carpets in the footwell, make sure the pedals still have sufficient clearance. During sudden driving or braking maneuvers the objects could get caught between or under the pedals. You could then no longer brake or accelerate. This could lead to accidents and injury.
! Allow the engine to warm up under low
load use. Do not place full load on the engine until the operating temperature has been reached. Avoid spinning of a drive wheel for an extended period when driving off on slippery road surfaces.
This may cause serious damage to the engine and the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.
i During the brief warm-up, transmission
upshifting is delayed. This allows the catalytic converter to heat up more quickly to operating temperature.
Gear selector lever
Gearshift pattern for automatic transmission : Button for selecting park position P j Park position k Reverse gear i Neutral position h Drive position G Warning! It is dangerous to shift the automatic transmission out of park position P or neutral position N if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
! Only shift the automatic transmission into reverse gear R or park position P when the vehicle is stopped. Otherwise the automatic transmission could be damaged.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 292
Version: 2.11.8.1
292 Automatic transmission
! The vehicle must be stopped when you
shift the automatic transmission Rdirectly between drive position D and
reverse gear R
Rdirectly between reverse gear R and
drive position D
Rdirectly into park position P Otherwise the automatic transmission could be damaged.
When trying to free a vehicle stuck in mud or snow, see “Rocking the vehicle” (Y page 295). i Shifting the automatic transmission out of
park position P is only possible with the brake pedal depressed. Without the brake pedal depressed, the gear selector lever can be moved up or down, but the parking pawl remains engaged, not allowing shifting to occur.
i The gear selector lever always returns to
its original position. The current transmission position P, R, N, or D appears in the multifunction display (Y page 294).
Shifting into park position P X With the vehicle at a standstill, press button : on the gear selector lever.
SmartKey: When you turn off the engine using the SmartKey, and remove the SmartKey from the starter switch or open a front door, the automatic transmission will shift into park position P automatically. KEYLESS-GO: When you turn off the engine using the KEYLESS-GO start/stop button and open a front door, the automatic transmission will shift into park position P automatically. G Warning! Keep in mind that turning off the engine alone only will shift the automatic transmission into neutral position N automatically.
Always shift the automatic transmission into park position P before turning off the engine. Otherwise the vehicle could roll away which could result in an accident and/or serious personal injury.
i Moving the gear selector lever up or down
shifts the automatic transmission out of park position P.
HOLD function or DISTRONIC PLUS: The automatic transmission will shift into park position P automatically when HOLD function or DISTRONIC PLUS brings your vehicle to standstill. In addition, at least one of the following conditions must be met: RThe engine is turned off. RThe driver’s door is opened and the seat
belt is not inserted in the seat belt buckle. In addition to shifting into park position P, the electronic parking brake will engage automatically.
Shifting into neutral position N X With the vehicle at a standstill, depress the
brake pedal.
X Move the gear selector lever up or down to
the resistance point to select neutral position N.
When you turn off the engine, the automatic transmission will shift into neutral position N automatically. SmartKey: Removing the SmartKey from the starter switch or opening a front door after turning off the engine will shift the automatic transmission into park position P automatically. KEYLESS-GO: Opening a front door after turning off the engine will shift the automatic transmission into park position P automatically. Remaining in neutral position N If you want the automatic transmission to remain in neutral position N, e.g. when taking
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 293
Version: 2.11.8.1
the vehicle through an automatic conveyor- type car wash, observe the following instructions. G Warning! When leaving the SmartKey in the starter switch, do not leave children unattended in the vehicle. It is possible for children to switch on the ignition which could result in unsupervised use of vehicle equipment. Unsupervised use of vehicle equipment could result in an accident and/or serious personal injury.
With SmartKey: X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the
brake pedal and keep it pressed.
X Shift the automatic transmission into
neutral position N.
X Release the brake pedal. X If engaged release the electronic parking
brake manually.
X Switch off the ignition and leave the
SmartKey in the starter switch.
With KEYLESS-GO: X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the
brake pedal and keep it pressed.
X Shift the automatic transmission into park
position P.
X Release the brake pedal. X Remove the KEYLESS-GO start/stop
button from the starter switch.
X Insert the SmartKey into the starter switch. X Switch on the ignition. X Depress the brake pedal and keep it
pressed.
X Shift the automatic transmission into
neutral position N.
X Release the brake pedal.
Automatic transmission 293
X If engaged release the electronic parking
brake manually.
X Switch off the ignition and leave the
SmartKey in the starter switch.
Shifting into reverse gear R X With the vehicle at a standstill, depress the
brake pedal.
X Move the gear selector lever up past the
resistance point.
Shifting into drive position D X With the vehicle at a standstill, depress the
brake pedal.
X Move the gear selector lever down past the
resistance point.
Shifting procedure The automatic transmission selects individual gears automatically, depending on Rthe selected gear range (Y page 295) Rthe selected program mode:
C/S (Y page 296) or M (AMG vehicles only) (Y page 298) Rthe position of the accelerator pedal Rthe vehicle speed With drive position D selected, you can influence transmission shifting by Rlimiting the gear range Rextending the gear range Rchanging the gears manually (AMG vehicles
only)
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 294
Version: 2.11.8.1
294 Automatic transmission
Transmission positions The current transmission position appears in the multifunction display.
: Transmission position indicator If the current transmission position does not appear in the multifunction display due to a malfunction, for example, make sure that the automatic transmission is in the desired position. X Shift the automatic transmission into drive
position D.
X Select automatic program mode S. X Do not limit the gear range. X Drive off carefully.
Effect
B Park position
Shift the automatic transmission into park position P only when the vehicle is stopped. The park position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always engage the electronic parking brake in addition to shifting the automatic transmission into park position P to secure the vehicle. If the vehicle’s electrical system is malfunctioning, the automatic transmission could remain locked in park position P. X Have the vehicle’s electrical
system checked at an authorized Mercedes-Benz Center as soon as possible.
C Reverse gear
Shift the automatic transmission into reverse gear R only when the vehicle is stopped.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 295
Version: 2.11.8.1
Effect
A Neutral position
No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). To avoid damage to the transmission, never shift the automatic transmission into neutral position N while driving. Exception: If the ESC is switched off or malfunctioning, shift the automatic transmission into neutral position N if the vehicle is in danger of skidding. ! Coasting the vehicle, or driving
for any other reason with the automatic transmission in neutral position N can result in transmission damage that is not covered by the Mercedes-Benz Limited Warranty.
7 Drive position
The automatic transmission shifts automatically. All forward gears are available.
Driving tips Kickdown Use the kickdown when you want maximum acceleration. X U.S. vehicles except AMG vehicles:
Fully depress the accelerator pedal. Depending on the engine speed the automatic transmission shifts into a lower gear.
X Canada vehicles and AMG vehicles: Depress the accelerator pedal past the point of resistance. Depending on the engine speed the automatic transmission shifts into a lower gear.
Automatic transmission 295
Rocking the vehicle Rocking the vehicle by shifting the automatic transmission directly between drive position D and reverse gear R can help free a vehicle stuck in mud or snow. The engine control system of this vehicle electronically limits directly shifting the automatic transmission between drive position D and reverse gear R to very low speeds, i.e. approximately 5 mph (9 km/h). To shift the automatic transmission directly between drive position D and reverse gear R, move the gear selector lever up or down past the resistance point.
Working on the vehicle G Warning! When working on the vehicle, engage the electronic parking brake and shift the automatic transmission into park position P. Otherwise the vehicle could roll away which could result in an accident and/or serious personal injury.
Gear ranges With the automatic transmission in drive position D and driving in automatic program mode C or S, you can limit or extend the gear range, see “One-touch gearshifting” (Y page 297). The current gear range appears in the multifunction display.
: Gear range indicator
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 296
Version: 2.11.8.1
296 Automatic transmission
Effect
= With this selection you can use the
braking effect of the engine.
5 Allows the use of the engine’s
braking effect when driving Ron steep downgrades Rin mountainous regions Runder extreme operating
conditions
4 For maximum use of the engine’s
braking effect on very steep or lengthy downgrades.
Automatic shift program The program mode selector switch is used to adjust Rthe shift program Rthe suspension tuning of the AIRMATIC or
the ABC system
Rthe engine control
Program mode selector switch on AMG vehicles C Comfort S Sport M Manual
For standard driving For sporty driving For manual gearshifting
The current program mode appears in the multifunction display.
: Program mode indicator You should only change the program mode when the automatic transmission is in park position P. The last selected automatic program mode (C or S) is active when the engine is restarted. X Press the program mode selector switch repeatedly until the letter of the desired program mode appears in the multifunction display.
Program mode selector switch C Comfort S Sport
For comfort driving For sporty driving
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 297
Version: 2.11.8.1
Selecting program mode C means: RThe vehicle starts out more gentle, both forward and reverse, except when driving off with full throttle.
RTraction and driving stability are improved
on icy roads.
RUpshifts occur earlier even when you give
more gas. The engine then operates at lower revolutions and the wheels are less likely to spin.
Selecting program mode S means that upshifts occur later.
One-touch gearshifting With the automatic transmission in drive position D and driving in automatic program mode C or S, you can limit or extend the gear range using the steering wheel gearshift control. AMG vehicles: For information on using the steering wheel gearshift control in manual program mode M, see “Manual shift program” (Y page 298).
Steering wheel gearshift control (example illustration)
i You cannot shift with the steering wheel
gearshift control when the automatic transmission is in park position P, neutral position N, or reverse gear R.
Automatic transmission 297
Limiting gear range G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.
X Briefly pull left gearshift control :.
The automatic transmission will shift into the next lower gear as permitted by the shift program. This action simultaneously limits the gear range of the automatic transmission.
i To avoid overrevving the engine when
downshifting, the automatic transmission will not shift into a lower gear if the engine’s maximum speed would be exceeded.
Extending gear range X Briefly pull right gearshift control ;.
The automatic transmission will shift into the next higher gear as permitted by the shift program. This action simultaneously extends the gear range of the automatic transmission.
i If you press on the accelerator pedal
when the engine has reached the revolution limit of the current gear range, the automatic transmission will upshift beyond any gear range limit selected.
Canceling gear range limit X Pull and hold right gearshift control ; until the gear range indicator disappears from the multifunction display. The automatic transmission will shift from the current gear range directly into drive position D.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 298
Version: 2.11.8.1
298 Automatic transmission
Shifting into optimal gear range X Pull and hold left gearshift control :.
The automatic transmission will select the gear range suited for optimal acceleration and deceleration automatically. This will involve shifting down one or more gears.
Manual shift program The manual shift program is available on AMG vehicles only. Manual program mode M differs with regard to spontaneity, response time, and shifting smoothness from automatic program mode S. In manual program mode M, system- controlled automatic gearshifting is switched off. You need to change the gears by manually upshifting or downshifting using the steering wheel gearshift control.
Program mode selector switch on AMG vehicle C Comfort S Sport M Manual
For standard driving For sporty driving For manual gearshifting
The current program mode appears in the multifunction display (Y page 296). For information on automatic program mode (C or S), see “Automatic shift program” (Y page 296) and “One-touch gearshifting” (Y page 297).
Activating manual shift program X Press the program mode selector switch repeatedly until M appears in the multifunction display. The automatic transmission switches to manual program mode M. Automatic shifting is switched off. The gear range is not limited.
You can change the gears manually with drive position D selected. You can upshift or downshift through the gears in succession. i Manual program mode M will not be
stored. When the engine is turned off with manual program mode M selected, the automatic transmission will go to automatic program mode (C or S) when the engine is restarted.
Upshifting ! In manual program mode M, the
automatic transmission will not upshift, even if the engine has reached its overrevving range. Shift up into the next gear before the engine has reached its overrevving range. Make absolutely certain that the engine speed does not reach the red marking on the tachometer. Otherwise the engine could be damaged which is not covered by the Mercedes-Benz Limited Warranty.
X Briefly pull right gearshift control ;
(Y page 297). The automatic transmission shifts into the next higher gear.
Upshift indicator
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 299
Version: 2.11.8.1
In manual program mode M, upshift indicator ; in the multifunction display advises you to upshift before the engine reaches the overspeed range. Thus you can drive at the maximum engine speed for each gear without overrevving the engine. X Shift the automatic transmission from
current gear : into the next higher gear. The fuel supply will otherwise be interrupted to prevent the engine from overrevving.
Downshifting G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.
X Briefly pull left gearshift control :
(Y page 297). The automatic transmission shifts into the next lower gear.
i For maximum acceleration, pull and hold the left gearshift control. Depending on the engine speed the automatic transmission selects the optimal gear for maximum acceleration.
i When you brake or stop, the automatic transmission shifts down into a gear from which you can easily accelerate or take off.
Kickdown Using the kickdown while driving in manual program mode M is not possible.
Transfer case 299
Deactivating manual shift program X Press the program mode selector switch repeatedly until C or S appears in the multifunction display.
or X Restart the engine.
The automatic transmission will go to automatic program mode C.
Manual program mode M is not stored.
Emergency operation (limp-home mode) If vehicle acceleration becomes less responsive or sluggish or the automatic transmission no longer shifts, the automatic transmission is most likely operating in limp- home (emergency operation) mode. In this mode only second gear and reverse gear R can be selected. X Stop the vehicle in a safe location. X Shift the automatic transmission into park
position P.
X Turn off the engine. X Wait at least 10 seconds before restarting. X Restart the engine. X Shift the automatic transmission into drive position D (for second gear) or reverse gear R.
X Have the automatic transmission checked at an authorized Mercedes-Benz Center as soon as possible.
Transfer case
This section applies to vehicles equipped with all-wheel drive (4MATIC) only. Both the front and rear axles are powered at all times when the vehicle is being operated. ! Only conduct operational or performance tests on a two-axle dynamometer. If such tests are necessary, contact an authorized Mercedes-Benz Center. You could
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 300
Version: 2.11.8.1
300
Instrument cluster
otherwise seriously damage the brake system or the transfer case which is not covered by the Mercedes-Benz Limited Warranty.
! Because the ESC operates automatically,
the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the electronic parking brake is being tested on a brake test dynamometer or when the vehicle is being towed with one axle raised. Active braking action through the ESC may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.
Instrument cluster Introduction For a full view illustration of the instrument cluster, see “Instrument cluster” (Y page 29). G Warning! No messages will be displayed if either the instrument cluster or the multifunction display is inoperative. As a result, you will not be able to see information about your driving conditions, such as Rspeed Routside temperature Rwarning/indicator lamps Rmalfunction/warning messages Rfailure of any systems Driving characteristics may be impaired. If you must continue to drive, do so with added caution. Contact an authorized Mercedes- Benz Center as soon as possible. The language setting for the multifunction display can be changed via COMAND (Y page 81).
Activating the instrument cluster The instrument cluster is activated when you Ropen a door Rswitch on the ignition Rswitch on the exterior lamps
Adjusting the instrument cluster illumination
X To brighten illumination: Turn knob :
clockwise.
X To dim illumination: Turn knob :
counterclockwise.
i The instrument cluster illumination is
dimmed or brightened automatically to suit ambient light conditions. The instrument cluster illumination will also be adjusted automatically when you switch on the vehicle’s exterior lamps.
Coolant temperature gauge The coolant temperature gauge is located on the left side in the instrument cluster (Y page 29). G Warning! Driving when your engine is overheated can cause some fluids which may have leaked into the engine compartment to catch fire. You could be seriously burned.
216_AKB; 3; 90, en-US d2ureepe,
2009-05-15T11:47:50+02:00 - Seite 301
Version: 2.11.8.1
Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it. Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down. During severe operating conditions, e.g. stop- and-go traffic, the coolant temperature may rise close to 248‡ (120†), i.e close to the red zone of the temperature gauge. ! Excessive coolant temperature triggers a
warning in the multifunction display. The engine should not be operated with a coolant temperature above 248‡ (120†), i.e. in the red zone of the coolant temperature gauge. Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.
Tachometer The red marking on the tachometer (Y page 29) denotes excessive engine speed. ! Avoid driving at excessive engine speeds, as it may result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty.
To help protect the engine, the fuel supply is interrupted if the engine is operated within the red marking.
Outside temperature indicator The outside temperature indicator is on the bottom left-hand side of the instrument cluster (Y page 29). G Warning! The outside temperature indicator is not designed to serve as an ice-warning device and is therefore unsuitable for that purpose.
Driving systems
301
Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. The road may still be icy, especially in wooded areas or on bridges.
Fuel gauge The fuel gauge is on the left-hand side of the instrument cluster (Y page 29). Once the fuel level has fallen below the reserve mark, the yellow segment indicator for the fuel reserve comes on.
Driving systems Introduction This section describes the following driving systems of your vehicle: RCruise control RDISTRONIC PLUS RHill-start assist system RHOLD function RAIRMATIC RActive Body Control (ABC) RAll-wheel drive (4MATIC) RParktronic system RPark Assist RAdvanced Parking Guidance RRear view camera RNight View Assist RBlind Spot Assist The driving safety systems ABS, Adaptive Brake, Adaptive Brake Lights, BAS, BAS PLUS, EBP, ESC and PRE-SAFE® Brake are described in the “Safety and security” section (Y page 56).
216_AKB; 3; 90, en-US d2ureepe,
302 Driving systems