2007 Mercedes-benz CL Class Owners Manual

Problem (USA only)

(Canada only)

The red brake warning lamp comes on while the engine is running and an acoustic warning sounds.

Warning!

Driving with the brake warning lamp illumi- nated can result in an accident. Have your brake system checked immediately if the brake warning lamp stays on. Do not add brake fluid before checking the brake system. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot en- gine parts and the brake fluid catching fire. You can be seriously burned.

569

Possible cause/consequence There is a malfunction in: 앫 The fuel management system 앫 The ignition system 앫 The emission control system 앫 Systems which affect emissions Such malfunctions may result in excessive emissions values and may switch the en- gine to its limp-home (emergency opera- tion) mode.

Suggested solution 왘 Have the vehicle checked as soon as

possible by an authorized Mercedes-Benz Center. An on-board diagnostic connector is used by the service station to link the vehicle to the shop diagnostics system. It allows the accurate identification of system malfunctions through the read- out of diagnostic trouble codes. It is lo- cated in the front left area of the footwell.

Practical hints What to do if …?

Problem ± The yellow engine malfunc- tion indicator lamp comes on while driving.

i Some states may by law require you to visit a workshop as soon as the engine malfunction indicator lamp comes on. Check local require- ments.

570

Problem ± The yellow engine malfunc- tion indicator lamp comes on while driving.

Possible cause/consequence A loss of pressure has been detected in the fuel system. The fuel cap may not be closed properly or the fuel system may be leaky.

Your fuel tank is empty.

Practical hints What to do if …?

Suggested solution 왘 Check the fuel cap. If it is not closed properly: 왘 Close the fuel cap. If it is closed properly: 왘 Have the fuel system checked by an au-

thorized Mercedes-Benz Center.

왘 After refueling, start, turn off, and re- start the engine three or four times in succession.

The limp-home mode is canceled. You do not need to have your vehicle checked.

571

Practical hints What to do if …?

Problem l PRE-SAFE® Brake*: The red dis- tance warning lamp comes on while driving.

l DISTRONIC Plus* or PRE-SAFE® Brake*: The red distance warn- ing lamp comes on while driving and an acoustic warning sounds.

v The yellow ESP® warning lamp

flashes while driving.

572

Possible cause/consequence You are too close to the vehicle in front of you to maintain selected speed.

Suggested solution 왘 Apply the brakes immediately to in-

crease the following distance.

You are gaining too rapidly on the vehicle ahead of you. DISTRONIC Plus* or PRE-SAFE® Brake* has recognized a stationary obstacle on your probable line of travel.

The ESP® or electronic traction system has come into operation because of detected traction loss in at least one tire. Cruise control and DISTRONIC Plus* are de- activated.

왘 Apply the brakes immediately.

왘 Apply the brakes immediately. 왘 Carefully observe the traffic situation. You may need to brake or maneuver to avoid hitting an obstacle.

왘 When driving off, apply as little throttle

as possible.

왘 While driving, ease up on the accelera-

tor.

왘 Adapt your speed and driving to the pre-

vailing road and weather conditions.

왘 Do not deactivate the ESP®. Exceptions:

(컄 page 71).

Failure to follow these instructions increas- es the risk of an accident.

Problem v The yellow ESP® warning lamp comes on while the engine is running.

Possible cause/consequence The ESP® is deactivated. Risk of accident! Adapt your speed and driving to the prevail- ing road, weather, and traffic conditions.

ESP® is switched off due to a malfunction. Risk of accident! Adapt your speed and driving to the prevail- ing road, weather, and traffic conditions.

The yellow fuel tank reserve warning lamp in the fuel gauge comes on while driving. < The red seat belt telltale comes on for a maximum of 6 seconds after starting the engine.

The fuel level has gone below the reserve mark. The seat belt telltale reminds you and your passengers to fasten your seat belts before driving off.

Practical hints What to do if …?

Suggested solution 왘 Switch the ESP® back on (컄 page 69).

Exceptions: (컄 page 71).

If the ESP® cannot be switched back on: 왘 Have the system checked at an autho- rized Mercedes-Benz Center as soon as possible.

왘 Continue driving with added caution. 왘 Read and observe messages in the mul-

tifunction display (컄 page 580).

왘 Have the system checked at an autho- rized Mercedes-Benz Center as soon as possible.

왘 Refuel at the next gas station

(컄 page 509).

왘 Fasten your seat belts.

Regardless of whether the seat belts are fastened or not, the seat belt telltale al- ways comes on and remains lit for 6 seconds after starting the engine.

573

Practical hints What to do if …?

Problem < You hear a warning chime for a

maximum of 6 seconds after starting the engine.

< The red seat belt telltale comes on while the vehicle is standing still and the engine is running or during driving.

< During driving the red seat belt telltale flashes and you addition- ally hear an intermittent warning chime with increasing intensity.

i After 60 seconds with an unfastened seat belt the warning chime stops sounding and the seat belt telltale illuminates continuously.

574

Possible cause/consequence You have forgotten to fasten your seat belt. 왘 Fasten your seat belt.

Suggested solution

You and/or your front passenger have for- gotten to fasten your seat belts.

There are items placed on the front passen- ger seat and therefore the system senses the front passenger seat as being occupied.

The vehicle’s speed once exceeded 15 mph (25 km/h) and you and/or your front pas- senger have forgotten to fasten your seat belts. There are items placed on the front passen- ger seat and therefore the system senses the front passenger seat as being occupied.

The warning chime stops sounding.

왘 Fasten your seat belts.

The seat belt telltale goes out.

왘 Remove the items from the front pas-

senger seat and put them in a safe place. The seat belt telltale goes out.

왘 Fasten your seat belts.

The seat belt telltale goes out and the warning chime stops sounding.

왘 Remove the items from the front pas-

senger seat and put them in a safe place. The seat belt telltale goes out and the warning chime stops sounding.

The seat belt telltale will only go out if both, the driver and front passenger’s, seat belt are

fastened, or the vehicle is standing still and a front door is opened.

Practical hints What to do if …?

Problem = The red SRS indicator lamp

comes on while the engine is running.

Possible cause/consequence There is a malfunction in the supplemental restraint systems. The air bags or emergen- cy tensioning devices (ETDs) could deploy unexpectedly or fail to deploy in an accident.

Suggested solution 왘 Drive with added caution to the nearest

authorized Mercedes-Benz Center.

Warning!

In the event that a malfunction of the SRS is indicated as outlined above, the SRS may not be operational. For your safety, we strongly recommend that you contact an au- thorized Mercedes-Benz Center immediate- ly to have the system checked; otherwise the SRS may not be deployed when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpect- edly and unnecessarily which could result in an accident and/or injury to you or to others.

575

Practical hints What to do if …?

Problem H Combination low tire pres-

sure/TPMS malfunction telltale for the Advanced TPMS illumi- nates continuously.

Possible cause/consequence The Advanced TPMS detects a loss of pres- sure in at least one tire.

H Combination low tire pres-

sure/TPMS malfunction telltale for the Advanced TPMS flashes for 60 seconds and then stays il- luminated.

There is a malfunction in the Advanced TPMS.

Suggested solution 왘 Carefully bring the vehicle to a halt, avoiding abrupt steering and braking maneuvers. Observe the traffic situation around you.

왘 Read and observe messages in the mul-

tifunction display (컄 page 580).

If the tire inflation pressure in the respec- tive tire(s) has (have) been corrected, the combination low tire pressure/TPMS mal- function telltale goes out after few minutes driving. 왘 Read and observe messages in the mul-

tifunction display (컄 page 580).

왘 Have the Advanced TPMS checked by an authorized Mercedes-Benz Center. After the malfunction has been remedied the combination low tire pressure/TPMS malfunction telltale goes out after few minutes driving.

576

Warning!

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- mended by the vehicle manufacturer on the vehicle placard or the tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or the tire inflation pressure label, you should determine the proper tire infla- tion pressure for those tires). As an added safety feature, your vehicle has been equipped with a Advanced Tire Pres- sure Monitoring System (Advanced TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significant- ly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possi- ble, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.

Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehi- cle’s handling and stopping ability. Please note that the Advanced TPMS is not a sub- stitute for proper tire maintenance, and it is the driver’s responsibility to maintain cor- rect tire pressure, even if under-inflation has not reached the level to trigger illumination of the Advanced TPMS low tire pressure telltale.

Your vehicle has also been equipped with a Advanced TPMS malfunction indicator to in- dicate when the system is not operating properly. The Advanced TPMS malfunction indicator is combined with the low tire pres- sure telltale. When the system detects a malfunction, the telltale will flash for approx- imately 1 minute and then remain continu- ously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended.

Practical hints What to do if …?

Advanced TPMS malfunctions may occur for a variety of reasons, including the installa- tion of replacement or alternate tires or wheels on the vehicle that prevent the Ad- vanced TPMS from functioning properly. Al- ways check the Advanced TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to en- sure that the replacement or alternate tires and wheels allow the Advanced TPMS to continue to function properly.

577

Practical hints What to do if …?

Air bag off indicator lamp

Problem 59
The front passenger front air bag off indicator lamp illuminates and remains il- luminated with the weight of a typical adult or some- one larger than a small in- dividual on the front passenger seat.

Possible cause/consequence Suggested solution The system is malfunctioning.

왘 Have the system checked as soon as possible by an authorized

Mercedes-Benz Center.

왘 Also read and observe any messages in the multifunction display

and follow corrective steps (컄 page 580).

Warning!

If the 59 indicator lamp illuminates and remains illuminated with the weight of a typical adult or someone larger than a small individual on the front passen- ger seat, do not have any passenger use the front passenger seat until the system has been repaired.

578

Problem 59
The front passenger front air bag off indicator lamp does not illuminate and/or does not remain illuminat- ed with the weight of a typ- ical 12-month-old child in a standard child restraint or less on the front passen- ger seat.

Possible cause/consequence Suggested solution The system is malfunctioning.

왘 Make sure there is nothing between seat cushion and child seat and

Practical hints What to do if …?

check installation of the child seat.

왘 Make sure no objects applying supplemental weight onto the seat

are present.

왘 Make sure no objects which apply forces to the seat are present

(e.g. objects such as books, briefcases etc. lodged behind or around the seat, head restraints pushing against roof etc.). The system may recognize such forces as supplemental weight.

왘 If the front passenger front air bag off indicator lamp remains out,

have the system checked as soon as possible by an authorized Mercedes-Benz Center. Do not transport a child on the front pas- senger seat until the system has been repaired.

왘 Also read and observe any messages in the multifunction display

and follow corrective steps (컄 page 580).

Warning!

If the 59 indicator lamp does not illuminate or remains out with the weight of a typical 12-month-old child in a standard child restraint or less on the front

passenger seat, do not transport a child on the front passenger seat until the system has been repaired.

579

Practical hints What to do if …?

Vehicle status messages in the multi- function display

Warning and malfunction messages ap- pear in the multifunction display located in the instrument cluster. Certain warning and malfunction messag- es are accompanied by an audible signal. High-priority messages are shown in red on the multifunction display. Messages of lower priority are also shown in yellow or white. Address these messages accordingly and follow the additional instructions given in this Operator’s Manual.

Certain messages of high priority cannot be cleared from the multifunction display using # or L on the multifunction steering wheel (컄 page 257). Other messages of high priority and mes- sages of less immediate priority can be cleared from the multifunction display using # or L. They are then stored in the vehicle status message memory (컄 page 270). Remember that clearing a message will only make the message dis- appear. Clearing a message will not cor- rect the condition that caused the message to appear.

Warning!

No messages will be displayed if either the instrument cluster or the multifunction dis- play is inoperative.

As a result, you will not be able to see infor- mation about your driving conditions, such as speed or outside temperature, warn- ing/indicator lamps, malfunction/warning messages or the failure of any systems. Driving characteristics may be impaired.

If you must continue to drive, please do so with added caution. Contact an authorized Mercedes-Benz Center as soon as possible.

580

On the pages that follow, you will find a compilation of the most important warning and malfunction messages that may ap- pear in the malfunction display. For your convenience the messages are di- vided into two sections: 앫 Text messages (컄 page 582) 앫 Symbol messages (컄 page 593)

Warning!

All categories of messages contain impor- tant information which should be taken note of and, where a malfunction is indicated, ad- dressed as soon as possible at an autho- rized Mercedes-Benz Center.

Failure to repair condition noted may cause damage not covered by the Mercedes-Benz Limited Warranty, or result in property dam- age or personal injury.

i Switching on the ignition causes all instru- ment cluster lamps (except high beam headlamp indicator lamp and turn signal indicator lamps unless activated) as well as the multifunction dis- play to come on. Make sure the lamps and multi- function display are in working order before starting your journey.

Practical hints What to do if …?

581

Possible cause/consequence You have tried to shift the automatic trans- mission to D, R or N without stepping on the brake. You have tried to switch on cruise control below a speed of 20 mph (30 km/h).

ESP® is switched off. The automatic transmission is in position P, R or N. The system is overheated. The vehicle is secured in place by the elec- tronic parking brake. Cruise control is malfunctioning.

Possible solution 왘 Step on brake.

왘 Drive faster than 20 mph (30 km/h) and save the speed.

왘 Switch on ESP® (컄 page 72). 왘 Shift the automatic transmission to D (컄 page 389).

왘 Wait until the system cools down. 왘 Release electronic parking brake (컄 page 384).

왘 Have cruise control checked by an authorized Mercedes-Benz

Center.

Practical hints What to do if …?

Text messages

Display Apply brake to shift from 'P' Cruise control - - - mph (USA only) Cruise control - - - km/h (Canada only)

Cruise control inoperative

582

Practical hints What to do if …?

Possible solution 왘 Clean the DISTRONIC Plus* cover in the radiator grille

(컄 page 558).

왘 Restart the vehicle. 왘 Try activating DISTRONIC Plus* again later. 왘 Wait until the system cools down or the battery recovers. DISTRONIC Plus* will be operational again without you needing to restart the engine if: 앫 the dirt (e.g. slush) loosens while you are driving 앫 the system detects that the sensors* are fully available again 앫 the message in the multifunction display disappears

왘 Wait until the message in the multifunction display disappears.

Display DISTRONIC PLUS currently unavailable See Oper. Manual

Possible cause/consequence DISTRONIC Plus* is switched off and is temporarily unavailable. DISTRONIC Plus* is deactivated if: 앫 the DISTRONIC Plus* cover in the radia-

tor grille is dirty

앫 the radar sensors* do not sense any

other vehicles or objects, i.e. road sign or similar to this, for a long time

앫 the system is overheated 앫 its function is impaired as a result of

heavy precipitation or fog

앫 the battery voltage is insufficient DISTRONIC Plus* is switched off because the radar sensor system* is temporarily in- operative due to electromagnetic interfer- ence near television and radio transmitter stations, toll stations, speed measuring sys- tems, etc.

583

Practical hints What to do if …?

Display DISTRONIC PLUS inoperative

DISTRONIC PLUS override

DISTRONIC PLUS - - - mph (USA only) DISTRONIC PLUS - - - km/h (Canada only)

584

Possible cause/consequence DISTRONIC Plus* is malfunctioning. BAS Plus* and PRE-SAFE® Brake* are also not available. You have depressed the accelerator pedal, DISTRONIC Plus* is no longer controlling the speed of the vehicle. You have attempted to activate DISTRONIC Plus* at a speed below 20 mph (30 km/h) without the vehicle in front being displayed in the multifunction display (컄 page 411).

Possible solution 왘 Contact an authorized Mercedes-Benz Center as soon as pos-

sible.

왘 Release the accelerator pedal.

왘 Drive faster than 20 mph (30 km/h) and activate DISTRONIC

Plus* again.

ESP® is switched off. The automatic transmission is in position P, R or N. The system is overheated. The vehicle is secured in place by the elec- tronic parking brake. The driver’s door is open and the drivers seat belt is unbuckled. The hood is open.

왘 Switch on ESP® (컄 page 69). 왘 Shift the automatic transmission to D (컄 page 389).

왘 Wait until the system cools down. 왘 Release electronic parking brake (컄 page 384).

왘 Close the driver’s door and fasten your seat belt.

왘 Close the hood (컄 page 513).

Practical hints What to do if …?

Display Door Open Vehicle not in Park

Front pass. airbag disabled See Oper. Manual

Possible cause/consequence Possible solution You have opened the driver’s door and the automatic trans- mission is still in position D, R or N. Front passenger front air bag is deactivated while driving even though an adult or someone larger than a small individual is occupying the front passenger seat. Forces acting on the seat may make the system sense a decrease in weight.

왘 Before you leave the vehicle, make sure that the automatic transmission is shift to position P (컄 page 389) and that the electronic parking brake is engaged (컄 page 384).

Stop the vehicle in a safe location as soon as possible and check the front passenger seat for the following: 왘 Switch off the ignition (컄 page 336). 왘 Have the front passenger vacate the seat and exit the vehicle. 왘 Adjust the seat in a height position (컄 page 339). 왘 Make sure that no objects which apply forces to the seat are present (e.g.

objects such as books, briefcases etc. lodged underneath, behind or around the seat). Such forces may cause the system to sense that an oc- cupant of a lesser weight than actually present is on the front passenger seat.

왘 Keep the seat unoccupied, close the passenger door and switch on the ig-

nition (컄 page 336).

Monitor the 59 indicator lamp right of the instrument cluster (컄 page 50) and the multifunction display in the instrument cluster (컄 page 256) for the following: (Continued on next page)

585

Practical hints What to do if …?

Display Front pass. airbag disabled See Oper. Manual

Possible cause/consequence Possible solution

With the seat unoccupied and the ignition switched on (컄 page 336), 앫 the 59 indicator lamp right of the instrument cluster should

illuminate and remain illuminated, indicating that the OCS (컄 page 47) has deactivated the air bag.

앫 the message “Front passenger airbag enabled See Oper. Manual” or the message “Front passenger airbag disabled See Oper. Manual” should not appear in the multifunction display at any time the seat is unoccupied. Wait at least 60 seconds for the system to complete the necessary check cycles and to make sure neither message appears in the multifunction dis- play.

If above conditions are met, you can occupy the front passenger seat again. Depending on the front passenger classification sensed by the OCS (컄 page 47), the 59 indicator lamp will remain illuminated or go out. If above conditions are not met, the system is not working properly. Have the system checked as soon as possible by an authorized Mercedes-Benz Center.

Warning!

If the 59 indicator lamp re- mains illuminated with an adult occupant on the front passenger seat even after

performing the above corrective steps, do not have any passenger use the front pas- senger seat until the system has been re- paired.

586

Practical hints What to do if …?

Display Front pass. airbag enabled See Oper. Manual

Possible cause/consequence Possible solution Front passenger front air bag is activated while driving even though a child, small individual, or object below the system’s weight threshold is on the front passenger seat, or the front pas- senger seat is empty. Objects on the seat or forces acting on the seat may make the system sense supplemental weight.

Stop the vehicle in a safe location as soon as possible and check the front passenger seat for the following: 왘 Switch off the ignition (컄 page 336). 왘 Remove child and child restraint from front passenger seat and properly

secure the child in rear seat employing the child restraint if necessary.

왘 Remove any other items from on and around the front passenger seat and make sure the storage bag on the back of the front passenger seat is emp- ty.

왘 Make sure that no objects which apply forces to the seat are present (e.g. objects such as books, briefcases etc. lodged behind or around the seat, head restraints pushing against roof etc.). The system may recognize such forces as supplemental weight and sense that an occupant on the front passenger seat is of a greater weight than actually present.

왘 Keep the seat unoccupied, close the passenger door and switch on the ig-

nition (컄 page 336).

Monitor the 59 indicator lamp right of the instrument cluster (컄 page 50) and the multifunction display in the instrument cluster (컄 page 256) for the following: (Continued on next page)

587

Practical hints What to do if …?

Display Front pass. airbag enabled See Oper. Manual

Possible cause/consequence Possible solution

With the seat unoccupied and the ignition switched on (컄 page 336), 앫 the 59 indicator lamp right of the instrument cluster should

illuminate and remain illuminated, indicating that the OCS (컄 page 47) has deactivated the air bag.

앫 the message “Front passenger airbag enabled See Oper. Manual” or the message “Front passenger airbag disabled See Oper. Manual” should not appear in the multifunction display at any time the seat is unoccupied. Wait at last 60 seconds for the system to complete the necessary check cycles and to make sure neither message appears in the multifunction dis- play.

If above conditions are met, you can occupy the front passenger seat again. Depending on the front passenger classification sensed by the OCS (컄 page 47), the 59 indicator lamp will remain illuminated or go out. If above conditions are not met, the system is not working properly. Have the system checked as soon as possible by an authorized Mercedes-Benz Center.

Warning!

If the 59 indicator lamp re- mains illuminated with an adult occupant on the front passenger seat even after

performing the above corrective steps, do not have any passenger use the front pas- senger seat until the system has been re- paired.

588

Practical hints What to do if …?

Display Next Service X due in ... days due in ... mls (km) Only shift to position 'P' when vehicle is stationary Park Assist currently unavailable See Oper. Manual

Park Assist inoperative PRE-SAFE inoperative See Oper. Manual

Possible cause/consequence Service X must be carried out in ... days or after ... miles (kilometers) (컄 page 551).

Possible solution 왘 Have the maintenance service carried out by an authorized

Mercedes-Benz Center.

You have tried to Shift the automatic trans- mission to P using the gear selector lever al- though the vehicle is still in motion. Park Assist* is deactivated because the area around the sensors* in the front or the rear bumper (컄 page 559) is dirty. Park Assist* is deactivated because the battery voltage is insufficient. Park Assist* is switched off because the ra- dar sensor system* is temporarily inopera- tive due to electromagnetic interference near television and radio transmitter sta- tions, toll stations, speed measuring sys- tems, etc. Park Assist* is unavailable due to a mal- function. PRE-SAFE® itself has failed. All other occu- pant safety systems, such as the air bags, are still available.

왘 Stop the vehicle.

왘 Clean the front and rear bumper (컄 page 559).

왘 Have the battery checked by an authorized Mercedes-Benz

Center.

왘 Wait until the message in the multifunction display disappears.

왘 Contact an authorized Mercedes-Benz Center as soon as

possible.

왘 Contact an authorized Mercedes-Benz Center as soon as

possible.

589

Practical hints What to do if …?

Display Radar sensor deactivated See Oper. Manual

Service X due Service X exceeded by X days by XXX mls (km)

Possible cause/consequence You attempt to activate DISTRONIC Plus*, Park Assist* or PRE-SAFE® Brake* even though you have switched off the radar sen- sors* on the vehicle. Your vehicle is due for maintenance service (컄 page 551). Service X must be carried within the next ... or before you have driven ... miles (kilome- ters) .

Possible solution 왘 Check if the radar sensors* may be switched on (컄 page 272). 왘 Switch on the radar sensors* using the instrument cluster

control system.

왘 Have the maintenance service carried out by an authorized

Mercedes-Benz Center.

왘 Have the maintenance service carried out by an authorized

Mercedes-Benz Center as soon as possible.

! Failure to have the vehicle maintained in ac- cordance with the Maintenance Booklet and maintenance service indicator at the designated times/mileage will result in vehicle damage not covered by the Mercedes-Benz Limited Warranty. For more information, see “Mainte- nance” (컄 page 551).

590

Practical hints What to do if …?

Display Shift to P or N to start engine

Tire pressure monitor inoperative Tire pressure monitor inoperative No wheel sensors

Possible cause/consequence You have attempted to start the engine while the automatic transmission was set to position R or D. The Advanced TPMS or a wheel sensor is malfunctioning. The Advanced TPMS is deactivated because wheels without proper sensors were in- stalled.

Tire pressure monitor currently unavailable

The Advanced TPMS is unable to monitor the tire inflation pressure due to: 앫 a nearby radio interference source 앫 the on-board voltage is too low 앫 excessive wheel sensor temperatures

Possible solution 왘 Shift the automatic transmission to P or N (컄 page 389).

왘 Have the Advanced TPMS checked by an authorized

Mercedes-Benz Center.

왘 Have the wheel sensors installed by an authorized

Mercedes-Benz Center. As soon as all wheels with sensors have been mounted, the Advanced TPMS is switched back on after driving for several minutes.

As soon as the causes for the malfunction are no longer present, the Advanced TPMS automatically becomes active again after a few minutes driving.

Warning!

Continued driving with a flat tire will cause excessive heat build-up and possibly a fire.

Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle.

591

Possible cause/consequence The tire inflation pressure is being checked. 왘 Drive the vehicle for a few minutes.

Possible solution

The automatic transmission cannot be shift- ed out of the set position because of a malfunction.

If the automatic transmission is shift to position D (컄 page 389): 왘 Without changing the automatic transmission from

position D, drive to an authorized Mercedes-Benz Center.

If the automatic transmission is shift to position N, R or P: 왘 Do not drive. 왘 Consult an authorized Mercedes-Benz Center.

Practical hints What to do if …?

Display Tire pressures displayed after driving a few minutes Visit workshop without shifting gears

592

Symbol messages

Display

Malfunction Stop Vehicle!

Practical hints What to do if …?

Possible cause/consequence You have started driving although the vehi- cle level is still too low. The vehicle is raised. The ABC message goes out after a few seconds.

The vehicle is losing oil. The ABC message is continuously shown.

ABC is malfunctioning. The ABC message is continuously shown.

Possible solution 왘 Stop your vehicle as soon as it is safe to do

so.

왘 Wait until the message disappears from the

multifunction display. You may then drive off.

왘 Stop your vehicle as soon as it is safe to do

so.

왘 Call Roadside Assistance. 왘 Notify an authorized Mercedes-Benz Center. 왘 Do not turn steering wheel too far to avoid

damaging the front fenders.

왘 Listen for scraping noises. 왘 Do not exceed a speed of 50 mph (80 km/h). 왘 Contact an authorized Mercedes-Benz Cen-

ter as soon as possible.

593

Practical hints What to do if …?

Display

Malfunction

Possible cause/consequence The capability of the ABC system is restrict- ed. This can impair the handling.

Vehicle rising Please wait a moment

The vehicle’s level is too low while at a standstill. The vehicle will be raised.

Possible solution 왘 Do not exceed a speed of 50 mph (80 km/h). 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

왘 Do not drive off. 왘 Wait until the message disappears from the

multifunction display. You may then drive off.

ABS and ESP inoperative See Oper. Manual

ABS, ESP® as well as PRE-SAFE® are switched off due to a malfunction. BAS is also switched off. The brake system is still functioning nor- mally but without the ABS available. BAS Plus* and PRE-SAFE® Brake* are also not available.

왘 Continue driving with added caution. Wheels may lock during hard braking, reducing steer- ing capability.

왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions increases the risk of an accident.

594

Display

ABS and ESP currently unavailable See Oper. Manual

Practical hints What to do if …?

Possible solution 왘 Drive a short distance with gentle turns

above a speed of 12 mph (20 km/h). The message disappears when ABS and ESP® are again available.

When the voltage is above this value again, the ABS, ESP® and PRE-SAFE® are operational again and the message in the multifunction display should disappear. If the message in the multifunction display does not disappear: 왘 Have the generator (alternator) and the bat-

tery checked.

Possible cause/consequence ABS, ESP® as well as PRE-SAFE® are not available due to a malfunction. BAS is also switched off. It is possible that the self-diag- nostics have not yet been completed. The brake system still functions normally. BAS Plus* and PRE-SAFE® Brake* are also not available. The ABS, ESP® as well as PRE-SAFE® were deactivated because of insufficient power supply. The charging voltage has fallen be- low 10 volts. The brake system still functions normally but without the ABS, ESP® and PRE-SAFE® available. BAS Plus* and PRE-SAFE® Brake* are also not available.

595

Check brake fluid level

Possible cause/consequence There is insufficient brake fluid in the reser- voir.

Possible solution Risk of accident! 왘 Carefully stop the vehicle in a safe location or

as soon as it is safe to do so.

왘 Engage the electronic parking brake

(컄 page 637).

왘 Contact an authorized Mercedes-Benz Cen-

ter.

왘 Do not add brake fluid! This will not solve the

problem.

! If you find that the brake fluid in the brake fluid reservoir has fallen to the minimum mark or below, have the brake system checked for brake pad thickness and leaks.

Practical hints What to do if …?

Display

(USA only)

(Canada only)

Warning!

Driving with the message “Check brake fluid level ” displayed can result in an accident. Have your brake system checked immedi- ately. Do not add brake fluid before check- ing the brake system. Overfilling the brake fluid reservoir can result in spilling brake flu- id on hot engine parts and the brake fluid catching fire. You can be seriously burned.

596

Brake immediately

Possible cause/consequence A malfunction has occurred while DISTRONIC Plus* was switched on.

Practical hints What to do if …?

Possible solution 왘 While observing surrounding traffic condi- tions and when it is safe, immediately de- press the brake pedal firmly until the warning message disappears.

왘 Secure vehicle from rolling away before get-

ting out of it (컄 page 384).

EBV, ABS, ESP inoperative See Oper. Manual

ESP®, EBP and ABS are switched off due to a malfunction. BAS is also switched off. As a result, PRE-SAFE® is also inoperative. BAS Plus* and PRE-SAFE® Brake* are also not available.

왘 Continue driving with added caution. 왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions increases the risk of an accident.

Display

(USA only)

(Canada only)

(USA only)

(Canada only)

597

Practical hints What to do if …?

Service See Oper. Manual

Possible cause/consequence CL 600: The brake system sensors are malfunction- ing. The brake system continues to function normally with full brake force boost.

Possible solution 왘 Continue driving with added caution. 왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible.

Display

(USA only)

(Canada only)

Brake wear

The brake pads have reached their wear limit.

왘 Have the brake pads replaced as soon as

possible.

! Brake pad thickness must be visually checked by a qualified technician at the intervals specified in the Maintenance Booklet.

598

Parking brake See Oper. Manual

Possible cause/consequence The red indicator lamp for the electronic parking brake is either on or off and the yel- low warning lamp for the electronic parking brake comes on. The electronic parking brake is malfunctioning.

Display

(USA only)

(Canada only)

Practical hints What to do if …?

Possible solution To release: 왘 Pull handle of electronic parking brake

(컄 page 384).

or 왘 Drive off carefully (컄 page 384). 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

or 왘 Release electronic parking brake mechani-

cally (컄 page 637).

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

To engage: 왘 Switch off ignition and press handle for elec- tronic parking brake until the warning mes- sage on the multifunction display disappears.

599

Practical hints What to do if …?

Display

(USA only)

(Canada only)

Parking brake See Oper. Manual

Possible cause/consequence The red indicator lamp for the electronic parking brake flashes. The power supply for the electronic parking brake was malfunctioning or the electronic parking brake was previously mechanically released.

Possible solution 왘 Pull handle for electronic parking brake

(컄 page 384).

or 왘 Carefully drive off (컄 page 384). or 왘 Press handle for electronic parking brake un- til the warning message disappears from the multifunction display.

600

Parking brake See Oper. Manual

Possible cause/consequence The red indicator lamp for the electronic parking brake flashes and the yellow warn- ing lamp for the electronic parking brake comes on. The electronic parking brake is malfunctioning.

Display

(USA only)

(Canada only)

Practical hints What to do if …?

Possible solution 왘 Switch ignition off and back on again, and en-

gage or release electronic parking brake (컄 page 384).

or 왘 Carefully drive off (컄 page 384). 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

or 왘 Release electronic parking brake mechani-

cally (컄 page 637).

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

601

Practical hints What to do if …?

Parking brake See Oper. Manual

Display

(USA only)

(Canada only)

Possible cause/consequence When you engage or release the electronic parking brake, the red indicator lamp for the electronic parking brake flashes for approx.10 seconds. Afterward, it goes out or comes on continuously. The yellow warn- ing lamp for the electronic parking brake comes on. The electronic parking brake is malfunction- ing or overheated for example due to over- or undervoltage.

Possible solution 왘 Carefully drive off (컄 page 384). 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

In the event of overvoltage or undervoltage: 왘 Remove the cause of the overvoltage or und- ervoltage, e.g. charge the battery or restart the engine.

왘 Switch ignition off and back on again, and en-

gage or release electronic parking brake (컄 page 384).

If the electronic parking brake still cannot be re- leased: 왘 Release electronic parking brake mechani-

cally (컄 page 637).

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

(Continued on next page)

602

Display

Possible cause/consequence

Parking brake See Oper. Manual

(USA only)

(Canada only) Parking brake

inoperative

When you engage or release the electronic parking brake, the red indicator lamp for the electronic parking brake flashes and goes out after approx. 10 seconds. The yel- low warning lamp for the electronic parking brake comes on. The electronic parking brake is malfunctioning.

Practical hints What to do if …?

Possible solution If overheated: 왘 Let vehicle cool down, and do not engage electronic parking brake during this time.

or 왘 Switch ignition off and back on again, and en-

gage or release electronic parking brake.

왘 Switch ignition off and back on again, and en- gage electronic parking brake (컄 page 384).

If the electronic parking brake cannot be en- gaged: 왘 Shift the automatic transmission to P

(컄 page 389).

왘 Protect vehicle from rolling away while

parked by using a chock from the vehicle tool kit (컄 page 634).

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

603

Practical hints What to do if …?

Display

(USA only)

Please release parking brake

(Canada only) Please release parking brake

604

Possible cause/consequence The red indicator lamp for the electronic parking brake flashes and you also hear a warning signal. You are driving with the electronic parking brake activated, or you are carrying out an emergency brake application with the elec- tronic parking brake (컄 page 384).

Possible solution 왘 Release electronic parking brake. or 왘 Carefully drive off (컄 page 384). or 왘 Release the handle for electronic parking

brake.

The red indicator lamp for the electronic parking brake flashes and the yellow warn- ing lamp for the electronic parking brake comes on. You also hear a warning tone. The electronic parking brake is malfunction- ing; braking action is restricted.

While driving: 왘 Release the handle for electronic parking

brake.

While at a standstill: 왘 Switch off ignition and press handle for elec-

tronic parking brake until the warning mes- sage disappears from the multifunction display.

Practical hints What to do if …?

Display

(USA only)

Turn on the ignition to release the parking brake

Possible cause/consequence The yellow indicator lamp for the electronic parking brake comes on. You have tried to release the electronic parking brake, but the ignition was not switched on.

Possible solution 왘 Switch on the ignition (컄 page 336).

(Canada only)

Inoperative See Oper. Manual

ESP® as well as PRE-SAFE® are switched off due to a malfunction. In addition, the v warning lamp in the instrument cluster comes on. The ABS may not be operational.

왘 Continue driving with added caution. 왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions increases the risk of an accident.

605

Possible solution 왘 Continue driving with added caution. 왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions increases the risk of an accident.

Possible cause/consequence CL 600 only: ESP® as well as PRE-SAFE® are switched off due to a malfunction. In addition, the v and ; (USA only) or 3(Canada only) warning lamps come on in the instrument cluster. Brake force assistance is impaired and is sustained through an electric substitute function as long as the engine is running. The brake system continues to function normally. You will feel a pulsating effect at the brake pedal while braking. BAS Plus* and PRE-SAFE® Brake* are also not available.

Practical hints What to do if …?

Display

Inoperative See Oper. Manual

606

Display

Currently unavailable See Oper. Manual

Currently unavailable See Oper. Manual

Currently unavailable See Oper. Manual

Practical hints What to do if …?

Possible cause/consequence ESP® and PRE-SAFE® are temporarily un- available. It is possible that the self-diag- nostics have not yet completed. In addition, the yellow ESP® warning lamp v comes on. The brake system functions normally. BAS Plus* and PRE-SAFE® Brake* are also not available. ESP® and PRE-SAFE® are switched off due to undervoltage. It is possible that the bat- tery is not charged. The brake system functions normally. BAS Plus* and PRE-SAFE® Brake* are also not available. If the yellow ESP® warning lamp v flash- es while driving and this message appears, the electronic traction system has switched off to prevent overheating of the drive wheel brakes. BAS Plus* and PRE-SAFE® Brake* are also not available.

Possible solution Synchronize the ESP®: 왘 Drive a short distance with gentle turns at a

speed above 12 mph (20 km/h). The message disappears when ESP® is again available.

왘 Continue driving with added caution. 왘 Have the system checked at an authorized Mercedes-Benz Center as soon as possible. Failure to follow these instructions increases the risk of an accident.

As soon as the brakes have cooled off, the elec- tronic traction system switches on again. The message in the multifunction display disap- pears and the ESP® warning lamp v goes out.

607

Possible cause/consequence The battery is no longer charging. Possible causes: 앫 alternator malfunctioning 앫 broken poly-V-belt

Possible solution 왘 Stop the vehicle immediately in a safe loca-

tion and check the poly-V-belt.

If it is broken: 왘 Do not continue to drive. Otherwise the en-

gine will overheat due to an inoperative water pump which may result in damage to the en- gine.

왘 Notify an authorized Mercedes-Benz Center. If it is intact: 왘 Drive immediately to the nearest authorized

Mercedes-Benz Center.

There is a malfunction in the electronic system.

왘 Have the system checked by an authorized Mercedes-Benz Center as soon as possible.

Practical hints What to do if …?

Display

608

Practical hints What to do if …?

Display

Coolant, please refill See Oper. Manual

Possible cause/consequence The coolant level is too low.

Possible solution 왘 Add coolant (컄 page 518). 왘 If you have to add coolant frequently, have

the cooling system checked by an authorized Mercedes-Benz Center.

Warning!

Do not spill antifreeze on hot engine parts. Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts. You could be seriously burned.

! Do not ignore the low engine coolant level warning. Extended driving with the message and symbol displayed may cause serious engine damage not covered by the Mercedes-Benz Lim- ited Warranty. Do not drive without a sufficient amount of cool- ant in the cooling system. The engine will over- heat, causing major engine damage.

609

Practical hints What to do if …?

Display

Coolant level Stop vehicle! Switch engine off

Possible cause/consequence The coolant is too hot.

Possible solution 왘 Stop the vehicle in a safe location or as soon as it is safe to do so and immediately turn off the engine.

왘 Only start the engine again after the message disappears. You could otherwise damage the engine.

왘 Observe the coolant temperature gauge in

the instrument cluster (컄 page 30).

Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.

! The engine should not be operated with the coolant temperature above 248°F (120°C). Do- ing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.

During severe operating conditions, e.g. stop-and-go traffic, the coolant tem- perature may rise close to 248°F (120°C).

Warning!

앫 Driving when your engine is overheated can cause some fluids which may have leaked into the engine compartment to catch fire. You could be seriously burned.

앫 Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it.

610

Display

Coolant level Stop vehicle! Switch engine off

Possible cause/consequence The poly-V-belt could be broken.

Practical hints What to do if …?

Possible solution 왘 Stop the vehicle in a safe location or as soon as it is safe to do so and immediately turn off the engine.

왘 Check the poly-V-belt. If it is broken: 왘 Do not continue to drive. Otherwise the en-

gine will overheat due to an inoperative water pump which may result in damage to the en- gine.

왘 Notify an authorized Mercedes-Benz Center. If it is intact: 왘 Do not continue to drive the vehicle with this message displayed. Doing so could result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty.

왘 Observe the coolant temperature gauge in

the instrument cluster (컄 page 30).

(Continued on next page)

611

Practical hints What to do if …?

Display

Possible cause/consequence

Coolant level Stop vehicle! Switch engine off

Possible solution 왘 Restart the engine.

If this message disappears from the multi- function display: 왘 Drive immediately to the nearest autho-

rized Mercedes-Benz Center.

If this message does not disappear from the multifunction display: 왘 Call Roadside Assistance.

The cooling fan for the coolant is malfunc- tioning.

왘 Observe the coolant temperature gauge in

the instrument cluster (컄 page 30).

왘 Have the fan replaced as soon as possible.

왘 Close the doors.

You are driving with one or both doors open. The display symbol shows you which doors are open.

612

Display

Gas cap open

Possible cause/consequence A loss of pressure has been detected in the fuel system. The fuel cap may not be closed properly or the fuel system may be leaky.

Practical hints What to do if …?

Possible solution 왘 Check the fuel cap (컄 page 509). If it is not closed properly: 왘 Close the fuel cap. If it is closed properly: 왘 Have the fuel system checked by an autho-

rized Mercedes-Benz Center.

You are driving with the hood open.

왘 Stop your vehicle as soon as it is safe to do

so.

왘 Close the hood (컄 page 513). There is otherwise danger of an accident.

613

Practical hints What to do if …?

Display

Key not recognized

614

Possible cause/consequence The SmartKey with KEYLESS-GO* is not recognized while the engine is running be- cause the SmartKey with KEYLESS-GO* is not in the vehicle.

The SmartKey with KEYLESS-GO* is not recognized while the engine is running be- cause there is strong radio-frequency inter- ference.

The SmartKey with KEYLESS-GO* is mo- mentarily not recognized.

Possible solution 왘 Stop the vehicle in a safe location or as soon

as it is safe to do.

왘 Search for the SmartKey.

Otherwise the vehicle cannot be centrally locked nor can the engine be started again after the engine is stopped.

왘 Stop the vehicle in a safe location or as soon

as it is safe to do.

왘 Remove KEYLESS-GO* button from over

starter switch (컄 page 337).

왘 Operate the vehicle with the SmartKey in the

starter switch.

왘 Change the position of the SmartKey in the

vehicle.

왘 If necessary, operate vehicle using SmartKey

with KEYLESS-GO* in starter switch under KEYLESS-GO* button (컄 page 337).

Practical hints What to do if …?

Display

Close doors to lock them

Do not forget key

Please remove key Change key batteries

Key still in vehicle

Possible cause/consequence You wanted to lock the vehicle but the doors were not closed.

Possible solution 왘 Close doors and lock vehicle again.

This display appears (for a maximum of 60 seconds) if the driver’s door is opened with the engine turned off and no SmartKey in the starter switch. This message is only a reminder. You have forgotten to remove the SmartKey. The batteries in the SmartKey with KEYLESS-GO* are discharged.

왘 Take the SmartKey or SmartKey with

KEYLESS-GO* with you when leaving the vehicle.

왘 Remove the SmartKey from the starter

switch.

왘 Replace the batteries (컄 page 639).

A SmartKey with KEYLESS-GO* left in the vehicle was recognized while locking the ve- hicle from the outside.

왘 Take the SmartKey with KEYLESS-GO* out of

the vehicle.

615

Practical hints What to do if …?

Display

Key not recognized

Possible cause/consequence The SmartKey with KEYLESS-GO* is momentarily not recognized.

Possible solution 왘 Change the position of the SmartKey with

KEYLESS-GO* in the vehicle.

Key being initialized… Please wait Remove starting button, then insert key

Replace key

The SmartKey with KEYLESS-GO* is being initialized in the vehicle.

The KEYLESS-GO* system is malfunctioning.

왘 If necessary, operate vehicle using SmartKey

with KEYLESS-GO* in starter switch under KEYLESS-GO* button (컄 page 337).

왘 Wait until the message disappears from the

multifunction display.

왘 Remove KEYLESS-GO* button from the

starter switch (컄 page 337).

왘 Operate the vehicle with the SmartKey with

KEYLESS-GO* in the starter switch.

The SmartKey with KEYLESS-GO* must be replaced.

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

616

Display

Third brake lamp

Corner. lamp, Left Corner. lamp, Right Low beam, Left Low beam, Right Active headlamps inoperative AUTO lamps inoperative

Practical hints What to do if …?

Possible solution 왘 Contact an authorized Mercedes-Benz

Possible cause/consequence The high mounted brake lamp is malfunc- tioning. This message will only appear if all light emitting diodes have stopped working. The left-hand corner-illuminating lamp is malfunctioning. The right-hand corner-illuminating lamp is malfunctioning. The left low beam lamp is malfunctioning. 왘 Contact an authorized Mercedes-Benz

왘 Replace the bulb as soon as possible

왘 Replace the bulb as soon as possible

Center as soon as possible.

(컄 page 641).

(컄 page 641).

Center as soon as possible.

The right low beam lamp is malfunctioning. 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

The active headlamps are malfunctioning. 왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

The light sensor is malfunctioning. Daytime driving lamps are switched on.

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

To switch off the headlamps (U.S. vehicles only): 왘 In the instrument cluster control system, set

lamp operation to manual mode (컄 page 271).

왘 Switch off the headlamps using the exterior

lamp switch (컄 page 363).

617

Practical hints What to do if …?

Display

Turn signal, Rear Left Turn signal, Rear Right Turn signal, Left mirror

Turn signal, Right mirror

Turn signal, Front Left Turn signal, Front Right High beam, Left

High beam, Right

618

왘 Have the LEDs replaced as soon as possible.

Center as soon as possible.

Center as soon as possible.

왘 Contact an authorized Mercedes-Benz

Possible solution 왘 Contact an authorized Mercedes-Benz

Possible cause/consequence The left rear turn signal lamp is malfunction- ing. A substitute bulb is being used. The right rear turn signal lamp is malfunc- tioning. A substitute bulb is being used. The turn signal in the left exterior rear view mirror is malfunctioning. This message will only appear if all light emitting diodes have stopped working. The turn signal in the right exterior rear view mirror is malfunctioning. This message will only appear if all light emitting diodes have stopped working. The left front turn signal lamp is malfunc- tioning. The right front turn signal lamp is malfunc- tioning. The left high beam lamp is malfunctioning. 왘 Replace the bulb as soon as possible

왘 Contact an authorized Mercedes-Benz

왘 Contact an authorized Mercedes-Benz

Center as soon as possible.

Center as soon as possible.

왘 Have the LEDs replaced as soon as possible.

(컄 page 641).

The right high beam lamp is malfunctioning. 왘 Replace the bulb as soon as possible

(컄 page 641).

Practical hints What to do if …?

Display

License plate lamp, Left License plate lamp,