2002 Mercedes-benz C Class Coupe Owners Manual

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

64

Warning! Never let more people ride in the vehicle than there are seat belts available. Be sure everyone riding in the vehicle is correctly restrained with a separate seat belt.

Warning! Failure to wear and properly fasten and position your seat belt greatly increases your risk of injuries and their likely severity in an accident. You and your passengers should always wear seat belts. If you are ever in an accident, your injuries can be considerably more severe without your seat belt properly buckled. Without your seat belt buckled, you are much more likely to hit the interior of the vehicle or be ejected from it. You can be seriously injured or killed. In the same crash, the possibility of injury or death is lessened if you are wearing your seat belt.

Fastening seat belts

1 Latch plate 2 Buckle 3 Release button

Push latch plate (1) into buckle (2) until it clicks. Do not twist the belt. A twisted seat belt may cause injury.

The lap belt should be positioned as low as possible on your hips and not across the abdomen.

Warning! Always fasten your seat belt before driving off. Always make sure your passengers are properly restrained – even those sitting in the rear.

Tighten the lap portion to a snug fit by pulling shoulder portion up. The shoulder portion of the seat belt must be pulled snug and checked for snugness immediately after engaging it. Adjust seat belt so that shoulder portion is located as close as possible to the middle of your shoulder (it should not touch the neck). For this purpose, you can adjust the height of the belt outlet.

Restraint systems

65

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

66

P91.40-2284-26

4 Button for belt outlet height adjustment

To raise, slide belt outlet upward. To lower, press button (4) and slide belt outlet downward.

Operation of seat belts The inertia reel stops the belt from unwinding during sudden stops or when quickly pulling on the belt. The locking function of the reel may be checked by quickly pulling out the belt. Adjust seat belt so that shoulder portion is located as close as possible to the middle of your shoulder (it should not touch the neck).

Caution! For safety reasons, avoid adjusting the seat or seat back into positions which could affect the correct seat belt positioning.

Unfastening of seat belts Press release button (3) in the belt buckle (2). Allow the retractor to completely rewind the seat belt by guiding the latch plate (1).

Warning! USE SEAT BELTS PROPERLY.

• Seat belts can only work when used properly. Never wear seat belts in any other way than as described in this section, as that could result in serious injuries in case of an accident.

• Each occupant should wear their seat belt at all

times, because seat belts help reduce the likelihood of and potential severity of injuries in accidents, including rollovers. The integrated restraint system includes “SRS” (driver airbag, front passenger airbag, side impact airbags, head protection window curtain airbags for side windows), “ETR” (seat belt emergency tensioning retractors), and front seat knee bolsters. The system is designed to enhance the protection offered to properly belted occupants in certain frontal (front airbags) and side (side impact and window curtain airbags) impacts which exceed preset deployment thresholds.

• Never wear the shoulder belt under your arm,

against your neck or off your shoulder. In a crash, your body would move too far forward. That would increase the chance of head and neck injuries. The belt would also apply too much force to the ribs or abdomen, which could severely injure internal organs such as your liver or spleen.

• Never wear belts over rigid or breakable

objects in or on your clothing, such as eyeglasses, pens, keys etc., as these might cause injuries.

• Position the lap belt as low as possible on your hips and not across the abdomen. If the belt is positioned across your abdomen, it could cause serious injuries in a crash.

• Each seat belt should never be used for more

than one person at a time. Do not fasten a seat belt around a person and another person or other objects.

• Belts should not be worn twisted. In a crash, you wouldn’t have the full width of the belt to manage impact forces. The twisted belt against your body could cause injuries.

Restraint systems

67

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

68

• Pregnant women should also use a lap-

shoulder belt. The lap belt portion should be positioned as low as possible on the hips to avoid any possible pressure on the abdomen.

• Never place your feet on the instrument panel

or on the seat. Always keep both feet on the floor in front of the seat.

Warning! USE CHILD RESTRAINTS PROPERLY. Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deactivate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal injury will result.

According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. Infants and small children must ride in the back seats and be seated in an appropriate infant or child restraint system, which is properly secured with the vehicle’s seat belt, fully in accordance with the child seat manufacturer’s instructions. A child’s risk of serious or fatal injuries is significantly increased if the child restraints are not properly secured in the vehicle and the child is not properly secured in the child restraint. Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning.

BabySmartTM airbag deactivation system Special BabySmartTM compatible child seats, designed for use with the Mercedes-Benz system and available at any authorized Mercedes-Benz Center are required for use with the BabySmartTM airbag deactivation system. With the special child seat properly installed, the passenger front airbag will not deploy. The ü indicator lamp located in the center console will be illuminated, except with electronic key removed or in starter switch position 0. The system does not deactivate the door mounted side impact airbag.

Self-test BabySmartTM without special child seat installed After turning electronic key in starter switch to position 1 or 2, the ü indicator lamp located in the center console comes on for approximately 6 seconds and then extinguishes. If the indicator lamp should not come on or is continuously lit, the system is not functioning. You must see an authorized Mercedes-Benz Center before seating any child on the front passenger seat. See page 289 for notes on the ü indicator lamp.

Warning! The BabySmartTM airbag deactivation system will ONLY work with a special child seat designed to operate with it. It will not work with child seats which are not BabySmartTM compatible. Never place anything between seat cushion and child seat (e.g. pillow), since it reduces the effectiveness of the deactivation system. The bottom of the child seat must make full contact with the passenger seat cushion. An incorrectly mounted child seat could cause injuries to the child in case of an accident instead of protecting the child. Follow the manufacturer’s instructions for installation of special child seats. The passenger front airbag will not deploy only if the ü indicator lamp remains illuminated. Please be sure to check the indicator every time you use the special system child seat. Should the light go out while the restraint is installed, please check installation. If the light remains out, do not use the BabySmartTM restraint to transport children on the front passenger seat until the system has been repaired.

BabySmartTM is a trademark of Siemens Automotive Corp.

Restraint systems

69

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

70

Supplemental Restraint System (SRS) Airbags are intended as a supplement to seat belts. Airbags alone cannot protect as well as airbags plus seat belts in impacts for which the airbags were designed to operate, and do not afford any protection whatsoever in crashes for which the airbags are not designed to deploy. The SRS uses two crash severity levels (thresholds) to activate either the emergency tensioning retractor (ETR) or front airbag or both. Activation depends on the direction and severity of the impact exceeding the preset thresholds and whether the seat belt is fastened.

Seat belt fastened • first threshold exceeded: ETR activates • second threshold exceeded: airbag also activates

Seat belt not fastened Front seats: • first threshold exceeded: airbag activates, not ETR Rear seats: • first threshold exceeded: ETR activates Driver and front passenger and rear seat systems operate independently of each other.

Emergency tensioning retractor (ETR) The seat belts for the front and rear seats are equipped with emergency tensioning retractors. These tensioning retractors are located in each belt’s inertia reel and become operationally ready with the electronic key in starter switch position 1 or 2. The emergency tensioning retractors are designed to activate only when the seat belts are fastened during frontal impacts exceeding the first threshold of the SRS They remove slack from the belts in such a way that the seat belts fit more snugly against the body restricting its forward movement as much as possible.

In cases of other frontal impacts, angled impacts, roll- overs, certain side impacts, or other accidents without sufficient frontal or rear impact forces, the emergency tensioning retractors will not be activated. The driver and passengers will then be protected by the fastened seat belts and inertia reel in the usual manner.

Note: The front passenger ETR activates only if the front passenger seat is occupied. Heavy objects on the front passenger seat can appear to the “SRS” to indicate the presence of an occupant in that seat which causes the passenger front airbag to deploy and the ETR to activate in a crash exceeding the appropriate threshold.

Restraint systems

71

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

72

Airbags Front airbags

The most effective occupant restraint system yet developed for use in production vehicles is the seat belt. In some cases, however, the protective effect of a seat belt can be further enhanced by an airbag. In conjunction with wearing the seat belts, the driver and front passenger airbags can provide increased protection for the driver and front passenger in certain frontal impacts exceeding preset thresholds. Side impact and head protection window curtain airbags can provide increased protection to belted occupants on the impacted side of the vehicle in side impacts exceeding its preset threshold.

1 Driver airbag 2 Front passenger airbag

Warning! In the event a malfunction of the “SRS” is indicated as outlined above, the “SRS” may not be operational. For your safety, we strongly recommend that you visit an authorized Mercedes-Benz Center immediately to have the system checked; otherwise the “SRS” may not be activated when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.

Note: See page 285 for information on the supplemental restraint system (SRS) indicator lamp.

The operational readiness of the airbag system is verified by the indicator lamp “SRS” in the instrument cluster when turning the electronic key in starter switch to position 1. When turning the electronic key in starter switch to position 2 the indicator lamp “SRS” in the instrument cluster comes on. If no fault is detected, the lamp will go out when the engine is running. After the lamp goes out, the system continues to monitor the components and circuitry of the airbag system and will indicate a malfunction by coming on again. If the lamp does not come on at all or if it fails to extinguish or if it comes on thereafter, a malfunction in the system has been detected. The following system components are monitored or undergo a self-check: crash-sensor(s), airbag ignition circuits, front seat belt buckles, emergency tensioning retractors, seat sensor. Have the system checked at your authorized Mercedes-Benz Center immediately. In the operational mode, after the indicator lamp has gone out following the initial check, interruptions or short circuits in the airbag ignition circuit and in the driver and front passenger seat belt buckle harnesses, and low voltage in the entire system are detected and indicated.

Restraint systems

73

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

74

The driver and passenger front airbags are designed to activate only in certain frontal impacts exceeding a preset threshold. The front passenger airbag deploys only if the front passenger seat is occupied and the ü indicator lamp in the center console is not illuminated.

Note: Heavy objects on the front passenger seat can appear to the “SRS” to indicate the presence of an occupant in that seat which causes the passenger front airbag to deploy in a crash exceeding the appropriate threshold.

Side impact airbags, window curtain airbags

3 Side impact airbags 4 Window curtain airbags

Side impact airbags The side impact airbags are designed to activate only in certain side impacts exceeding a preset threshold. Only the side impact airbags on the impacted side of the vehicle deploy. The side impact airbag for the front passenger deploys only if the front passenger seat is occupied. The side impact airbag for the right rear passenger deploys only if a preset threshold is exceeded. The side impact airbag for the left rear passenger deploys together with the side impact airbag for the driver. Side impact airbags operate best in conjunction with a properly positioned and fastened seat belt.

Note: Heavy objects on front passenger seat can cause the front passenger side impact airbag to deploy in a crash.

Restraint systems

75

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

76

Window curtain airbag The head protection window curtain airbags afford greater protection against injuries to the head and upper body. They fill up in the area between the A and C pillars (see arrows) between the side windows and an occupant’s head. The window curtain airbags are designed to activate only in certain side impacts exceeding a preset threshold. Only the head protection window curtain airbag on the impacted side of the vehicle deploys.

Important! Airbags are designed to activate only in certain frontal (front airbags) impacts, or side (side impact and head protection window curtain airbags) impacts which exceed preset thresholds. Only during these types of impacts, if of sufficient severity to meet the deployment thresholds, will they provide their supplemental protection. The driver and passenger should always wear their seat belts, otherwise it is not possible for the airbags to provide their supplemental protection. In cases of other frontal impacts, angled impacts, roll-overs, other side impacts, rear collisions, or other accidents, the airbags will not be activated. The driver and passengers will then be protected by the fastened seat belts. We caution you not to rely on the presence of the airbags in order to avoid wearing your seat belt.

Warning! Airbags are designed to reduce the potential of injury in certain frontal (front airbags) impacts, or side (side impact and head protection window curtain airbags) impacts which may cause significant injuries, however, no system available today can totally eliminate injuries and fatalities. The activation of the “SRS” temporarily releases a small amount of dust from the airbags. This dust, however, is neither injurious to your health, nor does it indicate a fire in the vehicle. The dust might cause some temporary breathing difficulty for people with asthma or other breathing trouble. To avoid this, you may wish to get out of the vehicle as soon as it is safe to do so. If you have any breathing difficulty but cannot get out of the vehicle after the airbag inflates, then get fresh air by opening a window or door.

Your vehicle was originally equipped with airbags which are designed to activate in certain impacts exceeding a preset threshold to reduce the potential and severity of injury. It is important to your safety and that of your passenger that you replace deployed airbags and repair any malfunctioning airbags to ensure the vehicle will continue to provide crash protection for occupants.

Warning! To reduce the risk of injury when the front airbags inflate, it is very important for the driver and front passenger to always be in a properly seated position and to wear your seat belt. For maximum protection in the event of a collision always be in normal seated position with your back against the backrest. Fasten your seat belt and ensure that it is properly positioned on your body. Since the airbag inflates with considerable speed and force, a proper seating and hands on steering wheel position will help to keep you at a safe distance from the airbag. Occupants who are unbelted, out of position or too close to the airbag can be seriously injured by an airbag as it inflates with great force in the blink of an eye:

Restraint systems

77

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

78

• Sit properly belted in an upright position with

your back against the backrest.

• Adjust the driver seat as far as possible

rearward, still permitting proper operation of vehicle controls. The distance from the center of the driver’s breastbone to the center of the airbag cover on the steering wheel must be at least ten inches (25 cm) or more. You should be able to accomplish this by a combination of adjustments to the seat and steering wheel. If you have any problems, please see your authorized Mercedes-Benz Center.

• Do not lean with your head or chest close to the

steering wheel or dashboard.

• Keep hands on the outside of steering wheel rim. Placing hands and arms inside the rim can increase the risk and potential severity of hand/arm injury when driver front airbag inflates.

• Adjust the front passenger seat as far as

possible rearward from the dashboard when the seat is occupied.

• Occupants, especially children, should never lean their heads in the area of the door where the side airbag inflates. This could result in serious injuries or death should the airbag be triggered.

• Children 12 years old and under must never

ride in the front seat, except in a Mercedes-Benz authorized Baby SmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deactivate the passenger side front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal injury can result.

Failure to follow these instructions can result in severe injuries to you or other occupants.

Warning! Accident research shows that the safest place for children in an automobile is in the rear seat. Should you choose to place a child 12 years old or under in the front passenger seat of your vehicle, you must properly use a BabySmartTM child restraint which will turn off the passenger side front airbag. BabySmartTM will not, however, turn off the vehicle’s side impact airbag. It should be noted that with respect to both front and rear side impact airbags there is a possibility for a side airbag related injury if occupants, especially children, are not properly seated or restrained when next to a side airbag which needs to deploy rapidly in a side impact in order to do its job.

Warning! To help avoid the possibility of injury, please follow these guidelines: (1) occupants, especially children, should never place their bodies or lean their heads in the area of the door or rear quarter trim panels where the side airbag inflates. This could result in serious injuries or death should the side airbag be activated; (2) always sit upright, properly use the seat belts and use an appropriately sized infant or child restraint system for all children 12 years old or under; and (3) always wear seat belts properly.

Restraint systems

79

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

80

Warning! If you believe that, even with the use of these guidelines, it would be safer for your rear seat occupants to have both rear door mounted side airbags deactivated, then deactivation can be accomplished upon your written election to do so at your authorized Mercedes-Benz Center at an additional cost. Please contact your local authorized Mercedes-Benz Center or call our Customer Assistance Center at 1-800-FOR- MERCedes (1-800-367-6372) for details.

Safety guidelines for the seat belt, emergency tensioning retractor and airbag

Warning!

• Damaged seat belts or belts that were highly stressed in an accident must be replaced and their anchoring points must also be checked. Use only belts installed or supplied by an authorized Mercedes-Benz Center.

• Airbags and “ETR’s” are designed to function

on a one-time-only basis. An airbag or emergency tensioning retractor (ETR) that was activated must be replaced.

• No modifications of any kind may be made to any components or wiring of the “SRS”. This includes changing or removing any component or part of the “SRS”, the installation of additional trim material, badges etc. over the steering wheel hub, front passenger airbag cover, door trim panels, or door frame trims, and installation of additional electrical/ electronic equipment on or near “SRS” components and wiring. Keep area between airbags and occupants free from objects (e.g. packages, purses, umbrellas, etc).

• Do not pass belts over sharp edges. • Do not make any modification that could

change the effectiveness of the belts.

• Do not hang items such as coat hangers from

the coat hooks or handles over the door. These items may turn into projectiles and cause head and other injuries when curtain airbag is deployed.

• An airbag system component within the

steering wheel gets hot after the airbag has inflated. Do not touch.

• Improper work on the system, including

incorrect installation and removal, can lead to possible injury through an unintended activation of the “SRS”.

• In addition, through improper work there is a

risk of rendering the “SRS” inoperative or causing unintended airbag deployment. Work on the “SRS” must therefore only be performed by an authorized Mercedes-Benz Center.

• For your protection and the protection of others, when scrapping the airbag unit or emergency tensioning retractor, our safety instructions must be followed. These instructions are available from your authorized Mercedes-Benz Center.

• Given the considerable deployment speed and the textile structure of the airbags, there is the possibility of abrasions or other injuries resulting from airbag deployment.

When you sell your vehicle we strongly urge you to give notice to the subsequent owner that it is equipped with an “SRS” by alerting them to the applicable section in the Operator’s Manual.

Restraint systems

81

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

82

Infant and child restraint systems We recommend all infants and children be properly restrained at all times while the vehicle is in motion. All lap-shoulder belts except the driver seat belt have special seat belt retractors for secure fastening of child restraints. To activate, pull shoulder belt out completely and let it retract. During the seat belt retraction a ratcheting sound can be heard to indicate that the special seat belt retractor is activated. The belt is now locked. To deactivate, release seat belt buckle and let seat belt retract completely. The seat belt can again be used in the usual manner.

Note: For child seats with mounting fittings for tether anchorages refer to page 84 (installation of infant and child restraint systems).

Warning! Never release the seat belt buckle while vehicle is in motion, since the special seat belt retractor will be deactivated.

Important! The use of infant or child restraints is required by law in all 50 states and all Canadian provinces. Infants and small children should be seated in an appropriate infant or child restraint system properly secured by a lap-shoulder belt, and that complies with U.S. Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213. A statement by the child restraint manufacturer of compliance with this standard can be found on the instruction label on the restraint and in the instruction manual provided with the restraint. When using any infant or child restraint system, be sure to carefully read and follow all manufacturer’s instructions for installation and use. Please read and observe warning labels affixed to the inside of the vehicle and to infant or child restraints.

Warning! Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deactivate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal injury can result. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. Infants and small children must ride in back seats and be seated in an appropriate infant or child restraint system, which is properly secured with the vehicle’s seat belt, fully in accordance with the child seat manufacturer’s instructions.

Infants and small children should never share a seat belt with another occupant. During an accident, they could be crushed between the occupant and seat belt. Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning for children from 41 lbs. to the point where a lap/shoulder belt fits properly without one. When the child restraint is not in use, remove it from the vehicle or secure it with the seat belt to prevent the child restraint from becoming a projectile in the event of an accident. Do not leave children unattended in the vehicle; even if the children are secured in a child restraint system. Unsupervised children in a child restraint system may use vehicle equipment and may cause serious personal injury.

Restraint systems

83

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

84

Installation of infant and child restraint systems

Prior to installing a tether strap, fold backrest forward (page 215), guide tether strap through head restraints and rear shelf. Be carefully that the tether strap is not twisted. Fold backrest back until it locks in place.

Warning! Always lock backrest in its upright position when rear seat bench is occupied by passengers, or the extended cargo area is not in use. Check for secure locking by pushing and pulling on the backrest.

P91.22-2077-26

Fold up the anchorage rings (2).

The anchorage rings (1) are located on the back side of rear backrests.

Child seat mounts – “LATCH” type

To secure a tether strap to the anchorage, securely fasten the hook (3), which is part of the tether strap, to the anchorage ring (2). For safety, please make sure that the hook has attached to the ring beyond the safety catch, as illustrated.

This vehicle is provided with two “LATCH” (LOWER Anchors and Tethers for CHildren) type mounts (at each of the rear seats) for the installation of a “LATCH” child seat having the matching mounting fittings. The mounts can be folded back between the seat cushion and the backrest.

Restraint systems

85

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Restraint systems

86

To install a “LATCH” type child seat, the mounts (1) must be folded forward until they lock in place. To do so, grip inner side of mounts and fold forward. Install child seat according to the manufacturer’s instructions. The child seat must be firmly attached in the right and left side mounting fittings (1). To fold mounts (1) back, press down button (2) on each mount and return mount into its catch. Non-“LATCH” type child seats may also be used and are capable of being installed using the vehicle’s seat belt system. Install child seat according to the manufacturer’s instructions.

Warning! The “LATCH” mounting fittings are intended for children up to 22 kg (50 lbs) in weight. Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning for children from 41 lbs. to the point where a lap/shoulder belt fits properly without one. Before installing the child seat, make sure the mounting fittings (1) are folded out and locked in place. Install child seat according to manufacturer’s instructions. The child seat must be firmly attached in the right and left side mounting fittings (1). An incorrectly mounted child seat may come loose during an accident. Damaged or impact damaged child seats or child seat mounting fittings must be replaced. Do not leave children unattended in the vehicle, even if the children are secured in a child restraint system.

Steering wheel adjustment (manual)

P46.15-2062-26

Warning! Do not adjust the steering wheel while driving. Adjusting the steering wheel while driving, or driving without the adjustment locked could cause the driver to lose control of the vehicle.

Unlocking: Pull handle (1) out to its stop. Adjusting: Move steering wheel to the desired position. Locking: Push handle (1) in until it engages.

Important! Do not drive the vehicle until you have properly locked the steering column.

See “STEERING WHEEL ADJUST” on page 308 for malfunction and warning messages in the multifunction display.

Restraint systems

87

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Steering wheel adjustment

88

Steering wheel adjustment (electrical) (optional)

Warning! Do not adjust the steering wheel while driving. Adjusting the steering wheel while driving could cause the driver to lose the control of the vehicle. When leaving the vehicle always remove the electronic key from the starter switch and lock your vehicle. The steering wheel adjustment feature can also be operated with the driver’s door open. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.

The switch is located on the driver’s door.

1 Steering column, lengthen or shorten column

To adjust the steering wheel position, turn the electronic key in starter switch to position 1 or 2. With the driver’s door open, the steering wheel can also be operated with the electronic key removed or in starter switch position 0.

Move the switch to the front or rear.

2 Steering column, height

Move the switch up or down.

Note: The steering wheel adjustment can be stored together with the seat and exterior mirror adjustment. See page 93 for notes on the memory function.

Rear view mirrors

Inside rear view mirror Manually adjust the mirror.

Inside rear view mirror, automatic antiglare With the electronic key in starter switch position 2, the mirror reflection brightness responds to changes in light sensitivity. With the gear selector lever in position “R”, or with the interior light switched on, the mirror brightness does not respond to changes in light sensitivity.

Note: The automatic antiglare function does not react, if incoming light is not aimed directly at sensors in the mirror.

Warning! In the case of an accident liquid electrolyte may escape the mirror housing when the mirror glass breaks. Electrolyte has an irritating effect. Do not allow the liquid come into contact with eyes, skin, clothing, or respiratory system. In cases it does, immediately flush affected area with water, and seek medical help if necessary.

Rear view mirrors

89

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Rear view mirrors

90

Exterior rear view mirrors

The buttons are located above the exterior lamp switch. The memory button (4) is located on the driver’s door.

P88.70-2113-26

Warning! Exercise care when using the passenger side exterior mirror. The mirror surface is convex (outwardly curved surface for a wider field of view). Objects in mirror are closer than they appear. Check your inside rear view mirror or glance over your shoulder before changing lanes.

Exterior rear view mirror adjustment Turn the electronic key in starter switch to position 1 or 2. Push button to select mirror to be adjusted: Driver’s side – Push button (1). Passenger side – Push button (2). Push the adjustment button (3) up, down, left or right according to the setting desired.

Notes: The exterior rear view mirrors have electrically heated glass. The heater switches on automatically, depending on outside temperature. If an exterior mirror housing is forcibly pivoted from its normal position, it must be repositioned by applying firm pressure until it snaps into place.

Storing rear view mirror positions in memory (only vehicles with memory function) The exterior rear view mirror positions are stored in memory with the seat/steering wheel adjustment and can be recalled when necessary. See page 93 for notes on the memory function.

Parking position exterior mirror (only vehicles with memory function) The passenger side exterior mirror can be adjusted and programmed to assist the driver during parking maneuvers (e.g. to observe the curb or other objects close to the vehicle). With the electronic key in starter switch position 2, and the exterior rear view mirror switch in the passenger side position, the passenger side mirror will be turned downward when placing the gear selector lever in “R” reverse.

Note: For activating the mirror adjustment, see under individual setting menu “CONVENIENCE” – “MIRROR SETTING WHEN PARKING”, on page 134. The passenger side mirror will return to its previous position: • immediately at speeds above approx. 6 mph

(10 km/h) – independent of the engaged gear,

• after 10 seconds when shifting gear selector lever

from “R” Reverse,

• by pressing the driver’s side mirror button %.

To store passenger mirror parking position:

1. The vehicle must be stationary.

Turn the electronic key in starter switch to position 1 or 2.

2. Select passenger side mirror & and adjust the

mirror to view the curb.

3. Push the memory button “M” (4). 4. Within 3 seconds push bottom of adjustment

button (3). The mirror should not move. Repeat the memory procedure if the mirror moves.

Note: One stored parking position is available for each of the two electronic keys. This is only possible if you select “ON” in the menu, “SETTINGS KEY-DEPENDENT”, see under individual setting menu “CONVENIENCE” – “SETTINGS KEY- DEPENDENT”, see page 134.

Rear view mirrors

91

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Rear view mirrors

92

Driver’s side exterior rear view mirror, antiglare mode With the electronic key in starter switch position 2, the mirror reflection brightness responds to changes in light sensitivity. With the gear selector lever in position “R”, or with the interior light switched on, the mirror brightness does not respond to changes in light sensitivity.

Note: The automatic antiglare function does not react, if incoming light is not aimed directly at sensors in the inside rear view mirror.

Warning! In the case of an accident liquid electrolyte may escape the mirror housing when the mirror glass breaks. Electrolyte has an irritating effect. Do not allow the liquid come into contact with eyes, skin, clothing, or respiratory system. In cases it does, immediately flush affected area with water, and seek medical help if necessary.

Important! Electrolyte drops coming into contact with the vehicle paint finish can only be completely removed while in their liquid state, by applying plenty of water.

Memory function (optional)

The memory and stored position buttons are located on the doors.

1 Memory button, used to store selected positions

which can be retrieved by pressing

2 Stored position button

Turn to position “1”, “2”, or “3”

Warning! Do not activate the memory function while driving. Activating the memory function while driving could cause the driver to lose control of the vehicle.

Together with the driver’s seat position you can store the positions for steering wheel and exterior rear view mirrors. For the front passenger you can store the seat position. Three stored positions for the driver’s seat are available for each of the two electronic keys. This is only possible if you select “ON” in the menu, “SETTINGS KEY-DEPENDENT”, see under individual setting menu “CONVENIENCE” – “SETTINGS KEY- DEPENDENT”, see page 134.

Memory function

93

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Memory function

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

94

Storing positions into memory: With the electronic key in starter switch position 1 or 2 or with the relevant door open and the electronic key inserted in the starter switch. Adjust the seat to the desired position. Driver’s seat: You can also adjust the steering wheel and the exterior mirrors electrically for the driver’s seat. See page 90 for exterior rear view mirror adjustment and page 88 for steering wheel adjustment. Turn button (2) to selected memory position. Push memory button (1), release and push the position button (2) within 3 seconds.

Recalling positions from memory: To recall a seat /steering wheel/exterior rear view mirror position, turn button (2) to selected memory position and press to recall. The seat/ steering wheel/exterior rear view mirror movement stops when the button is released.

Caution! Do not operate the power seats using the memory button if the backrest is in an excessively reclined position. Doing so could cause damage to front or rear seats. First move backrest to an upright position.

Important! Prior to operating the vehicle, the driver should check and adjust if necessary the seat height, seat position fore and aft, and backrest angle to insure adequate control, reach and comfort. The head restraint should also be adjusted for proper height. See also airbag section for proper seat positioning. In addition, also adjust the steering wheel to ensure adequate control, reach, operation and comfort. Both the inside and outside rear view mirrors should be adjusted for adequate rearward vision. Fasten seat belts. Infants and small children should be seated in a properly secured restraint system that complies with U.S. Federal Motor Vehicle Safety Standard 213 and Canadian Motor Vehicle Safety Standard 213. All seat, head restraint, steering wheel, and rear view mirror adjustments as well as fastening of seat belts should be done before the vehicle is put into motion.

Warning! Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deactivate the passenger side front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal injury can result. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. Infants and small children must ride in back seats and be seated in an appropriate infant or child restraint system, which is properly secured with the vehicle’s seat belt, fully in accordance with the child seat manufacturer’s instructions. A child’s risk of serious or fatal injuries is significantly increased if the child restraints are not properly secured in the vehicle and the child is not properly secured in the child restraint.

Memory function

95

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instrument cluster

Instrument cluster

96

12

13

11

15

14

16

P54.30-5433-29

1 Knob for instrument cluster illumination,

see page 99
Reset knob for trip odometer, see page 101 and individual settings, see page 121

2 Tachometer 3 Speedometer 4 Left turn signal indicator lamp, see combination

switch on page 148

5 Electronic stability program (ESP) warning lamp,

see page 288

6 Indicator lamp without function. It illuminates with

the electronic key in starter switch position 2. It should go out when the engine is running.

7 Right turn signal indicator lamp, see combination

switch on page 148

8 Indicator lamp without function. It illuminates with

the electronic key in starter switch position 2. It should go out when the engine is running.

9 Multifunction display, see page 102

Malfunction and warning messages in the multifunction display, see page 290
10 Trip odometer, see page 101 and 106
11 Main odometer, see page 106
12 Display for program mode and gear range

indicators, page 249

13 Malfunction/warning message memory,

see page 119

14 Outside temperature indicator, see page 100
15 Digital clock

To set the time, see individual settings on page 121
16 Fuel gauge with reserve warning lamp, see page 286

Instrument cluster

97

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instrument cluster

98

Indicator lamps in the instrument cluster

High beam, see page 148

ABS malfunction, see page 287

ABS

Brake fluid low (except Canada). Parking brake engaged, see page 284
ESP. Adjust driving to road condition, see page 288
Fasten seat belts, see page 288

SRS malfunction, see page 285

Engine malfunction indicator lamp. If the malfunction indicator lamp comes on when the engine is running, it indicates a malfunction of the fuel management system, emission control system, systems which impact emissions, or the fuel cap is not closed tight. In all cases, we recommend that you have the malfunction checked as soon as possible, see page 283

Display illumination, changing basic settings for driving at dusk or in darkness: Rotate adjusting knob (1) clockwise – instrument lamp intensity increases. Rotate adjusting knob (1) counterclockwise – instrument lamp intensity decreases.

Note: It is not possible to select a basic brightness setting in daylight – the intensity is adjusted automatically.

Activating instrument cluster display The instrument cluster is activated by: • Opening the door1. • Pressing button (1) on the instrument cluster1. • Turning the electronic key in starter switch to

position 1 or 2.

• Switching on the exterior lamps.

Instrument cluster illumination The instrument cluster illumination is dimmed or brightened automatically to suit daylight lighting conditions. The instrument cluster illumination will also be adjusted when the vehicle’s exterior lamps are switched on.

1 The instrument cluster is activated for approximately 30 seconds.

Instrument cluster

99

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instrument cluster

100

Outside temperature indicator (14)

Warning! The outside temperature indicator is not designed to serve as an Ice-Warning Device and is therefore unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice.

The temperature sensor is located in the front bumper area. Due to its location, the sensor can be affected by road or engine heat during idling or slow driving. This means that the accuracy of the displayed temperature can only be verified by comparison to a thermometer placed next to the sensor, not by comparison to external displays (e.g. bank signs etc.).

Adaption to ambient temperature takes place in steps and depends on the prevailing driving conditions (stop- and-go or moderate, constant driving) and amount of temperature change.

Note: The unit for the temperature indicator display can be set in the individual setting menu “INSTRUMENT CLUSTER” – “TEMP. INDICATOR” on page 121.

Trip odometer (10) To reset to “0” miles/km: Activate the instrument cluster if it is not already activated, see page 99. Press button è or ÿ on the multifunction steering wheel repeatedly until the trip odometer appears if it is not displayed. See page 106. Press and hold button (1) on the instrument cluster, see page 99.

Tachometer (2) The red marking on the tachometer denotes excessive engine speed. Avoid this engine speed, as it may result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty. To help protect the engine, the fuel supply is interrupted if the engine is operated within the red marking.

Instrument cluster

101

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

102

Multifunction steering wheel, multifunction display

P54.30-4452-29

Depending on your vehicle’s equipment, you may use the buttons on the multifunction steering wheel to call up, control and set the following systems in the multifunction display:

1 Trip odometer and main odometer, see page 101 and

page 106
Flexible service system (FSS), see page 138
Vehicle speed, see page 106
Coolant temperature gauge, see page 137
Engine oil level indicator, see page 141

3 Navigation system, see page 116
4 Malfunction message memory, see page 119
5 Individual settings, see page 121
6 Trip computer, see page 117

After start After reset Fuel tank content

7 Telephone, see page 111

2 Audio systems, see page 108

Radio, see page 108
CD player, see page 109
Cassette player, see page 110

Press the è or ÿ button repeatedly until the required system is displayed. The display advances by one system each time the button is pressed. You may call up additional displays within some of these categories by pressing the j or k button.

Multifunction steering wheel, multifunction display

103

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

104

Warning! A driver’s attention to the road must always be his/ her primary focus when driving. For your safety and the safety of others, selecting features through the multifunction steering wheel should only be done by the driver when traffic and road conditions permit it to be done safely. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 50 feet (approximately 14 m) every second.

Note: The displays in the multifunction display can be set to German, English, French, Italian or Spanish language. See the individual setting menu “INSTRUMENT CLUSTER” – “TEXT” on page 121 for instructions on changing the language setting. The displays for the audio systems (radio, CD player, cassette player) will appear in English, regardless of the language selected.

Press button:

3 è for next system 4 ÿ for previous system 5 j for next display in system 6 k for previous display in system 7 æ to increase the volume, see page 136
8 ç to decrease the volume, see page 136
9 í to dial a telephone number, see page 111
10 ì to end a call

See page 111 for telephone and page 115 for instructions on answering an incoming call.

11 Horn pad

Press the è or ÿ button repeatedly until the required system is displayed. The display advances by one system each time the button is pressed. You may call up additional displays in some systems by pressing the j or k button.

1 Multifunction display 2 Multifunction steering wheel Turn the electronic key in starter switch to position 1 or 2.

Multifunction steering wheel, multifunction display

105

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

106

Trip and main odometer and sub menu

P54.30-4453-29

Press è or ÿ button repeatedly until the trip odometer and main odometer display (1) appears. Press the j or k button repeatedly until the required display (2, 3, 4, 5, 1) appears. Pressing the è or ÿ button displays the next or previous system.

1 Trip odometer and main odometer

See page 101 for instructions on resetting the trip odometer.

2 Coolant temperature gauge, see page 137
3 Vehicle speed if “SPEED DISP.” is selected in the

individual setting menu “INSTRUMENT CLUSTER” - “SELECT DISPLAY”, refer to page 124
Outside temperature if “OUTSIDE TEMPERATURE” is selected in the individual setting menu “INSTRUMENT CLUSTER” - “SELECT DISPLAY”, see page 124

4 FSS (Flexible service system), see page 138
5 Engine oil level indicator, see page 141

Multifunction steering wheel, multifunction display

107

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

108

Audio systems Radio

P54.30-3634-27

1 Audio system is switched off. 2 The radio is switched on. 3 Wave band setting and memory location number,

where appropriate.

4 Station name setting or station frequency. 5 This only appears when “MEMORY” rather than

“STATION SEARCH” has been selected in the setting menu “VEHICLE” – “PRESS BUTTON IN AUDIO MODE”, page 132.

The radio must be switched on. Press the è or ÿ button repeatedly until display (2) appears. Press button j or k repeatedly until the required station or frequency is displayed. Use the j of k button to select a stored station or station frequency. This depends on the selection made in the setting menu “PRESS BUTTON IN AUDIO MODE”. See individual settings, page 132.