2009 Jeep Patriot Owners Manual

Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” in the Safety Tips section of this manual.

The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.

MAINTAINING YOUR VEHICLE 377

Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.

CAUTION!

Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.

378 MAINTAINING YOUR VEHICLE

WARNING!

A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.

In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to manufacturers specifica- tions, should be obtained immediately.

To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires

vehicle.

disconnected for a prolonged period.

Cooling System

WARNING!

• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.

(Continued)

WARNING! (Continued)

• You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.

Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.

MAINTAINING YOUR VEHICLE 379

Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. Cooling System — Drain, Flush And Refill Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (antifreeze). Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

380 MAINTAINING YOUR VEHICLE

CAUTION!

• Mixing of engine coolant (antifreeze) other than specified Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion pro- tection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emer- gency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator.

(Continued)

CAUTION! (Continued)

• This vehicle has not been designed for use with (anti- Propylene Glycol based engine coolant freeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended.

Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).

When adding engine coolant (antifreeze), a minimum solution of 50% recommended MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology), or equivalent, in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are antici- pated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes.

MAINTAINING YOUR VEHICLE 381

Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze) and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.

WARNING!

• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pres- sure cap while the system is hot or under pressure. (Continued)

382 MAINTAINING YOUR VEHICLE

WARNING! (Continued)

• Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.

Disposal Of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.

Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the “ADD” and “FULL” lines shown on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for the coolant freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.

Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check the coolant freeze point in the radiator and in the coolant recovery bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant recovery bottle must also be protected against freez- ing.

MAINTAINING YOUR VEHICLE 383

• If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.

384 MAINTAINING YOUR VEHICLE

Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.

Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on.

Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. The brake fluid level should be checked when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. If your vehicle is equipped with a manual NOTE: transaxle , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transaxle clutch release system should not require fluid replacement during the life of the vehicle. If the brake fluid reservoir is low and the brake system does not indicate any leaks or other problems, it may be a result of a leak in the hydraulic clutch release system. See your local authorized dealer for service.

Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

WARNING!

• Use of a brake fluid that may have a lower initial boiling point or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.

MAINTAINING YOUR VEHICLE 385

CAUTION!

Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transaxle.

Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. NOTE: Do not allow petroleum-based fluid to contami- nate the brake fluid as seal damage will result!

386 MAINTAINING YOUR VEHICLE

Automatic Transaxle (CVT)

Selection Of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance. Use only the manufacturer’s recommended transmission fluid which has been formulated with special metal to metal friction coefficient additives to provide the proper steel belt traction on the drive and driven pulleys. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

CAUTION!

Using a transmission fluid other than the manufac- turer’s recommended fluid will cause belt slip and result in a complete transmission failure! Refer to “Fluids, Lubricants, and Genuine Parts” in this sec- tion for the correct fluid type.

Fluid Level Check The fluid level in the automatic transaxle should be checked only by a trained technician. Fluid And Filter Changes Refer to the “Maintenance Schedule” in Section 8 for the correct maintenance interval. Special Additives Do not add any materials (other than leak detection dyes) to Continuously Variable Transaxle (CVT) Fluid (CVTF+4). CVTF+4 is an engineered product and its performance may be impaired by supplemental additives. Manual Transaxle

Lubricant Selection Use only the manufacturers recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16 in (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubri- cant has become contaminated with water. NOTE: changed immediately.

If contaminated with water, the fluid should be

MAINTAINING YOUR VEHICLE 387

Rear Drive Assembly (RDA) – AWD/4WD Models Only

Lubricant Selection Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Fluid Level Check Visually inspect the unit at each oil change for leakage. If leakage is detected, check the fluid level by removing the fill plug. The fluid level should be maintained between the bottom of the fill hole to 1/8 in (4 mm) below the fill hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Refer to the “Maintenance Schedule” in Section 8 for the correct maintenance interval.

388 MAINTAINING YOUR VEHICLE

Power Transfer Unit (PTU) – AWD/4WD Models Only

Lubricant Selection Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Fluid Level Check Visually inspected the unit at each oil change for leakage. If leakage is detected, Check the fluid level by removing the fill plug. The fluid level should be maintained be- tween the bottom of the fill hole to 1/8 in (4 mm) below the fill hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Refer to the “Maintenance Schedule” in Section 8 for the correct maintenance interval.

Appearance Care And Protection From Corrosion

Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.

What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes of corrosion are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea coast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water.

MAINTAINING YOUR VEHICLE 389

• If insects, tar or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.

390 MAINTAINING YOUR VEHICLE

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner.

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.

mud or stone shields behind each wheel.

Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use MOPAR威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only MOPAR威 cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.

with a clean, dry towel.

YES Essentials威 Fabric Cleaning Procedure – If Equipped YES Essentials威 seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essen-

tials威 products.

MAINTAINING YOUR VEHICLE 391

Interior Care Use MOPAR威 Total Clean to clean fabric upholstery and carpeting. Use MOPAR威 Total Clean to clean vinyl upholstery. MOPAR威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp, soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition.

392 MAINTAINING YOUR VEHICLE

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm.

Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and, therefore, different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.

Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products which may cause undesir- able reflections. Use soap and warm water to restore the low glare surface.

MAINTAINING YOUR VEHICLE 393

Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the seat belts from the car to wash them. Replace the seat belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft cloth.

Instrument Panel Bezels

CAUTION!

When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface.

Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean, damp rag. 2. Dry with a soft cloth.

394 MAINTAINING YOUR VEHICLE

FUSES

Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “Engine Compartment” in this section of the Owner’s Manual for the underhood location of the IPM. Cavity Cartridge

Description

Mini- Fuse

Fuse Empty

15 Amp Lt Blue 10 Amp Red 10 Amp Red

Empty AWD/4WD ECU Feed CHMSL Brake Switch Feed Ignition Switch Feed/ OCM

Cavity Cartridge

Fuse

10

11

12

40 Amp Green

Mini- Fuse 20 Amp Yellow 10 Amp Red

30 Amp Green 30 Amp Green

20 Amp Yellow 15 Amp Lt Blue 20 Amp Yellow

Description

Trailer Tow

IOD Sw/Pwr Mir/ Steering Cntrl Sdar/ Hands-Free Phone IOD Sense1

IOD Sense2

Power Seats

CCN Power Locks/ Interior Lighting Power Outlet

Ign Run/Acc Inverter

Cavity Cartridge

Fuse

13

14

15

16

17

18

19

40 Amp Green

40 Amp Green

Mini- Fuse 20 Amp Yellow 10 Amp Red

15 Amp Lt Blue

10 Amp Red

20 Amp Yellow

Description

Pwr Run/Acc Outlet RR/Dome Lamp IOD CCN

RAD Fan Relay Bat- tery Feed IGN Run/Acc Dome Lamp/Sunroof/Rear Wiper Motor/ACC Inverter IOD Feed Mod-Wcm

ASD Relay Contact PWR Feed PWR Amp 1 & Amp 2 Feed

Cavity Cartridge

Fuse

20

21

22

23

24

25

26

27

MAINTAINING YOUR VEHICLE 395

Mini- Fuse 15 Amp Lt Blue 10 Amp Red

10 Amp Red 15 Amp Lt Blue 15 Amp Lt Blue 10 Amp Red 15 Amp Lt Blue 10 Amp Red

Description

IOD Feed Radio

IOD Feed Intrus Mod/Siren (If Equipped) IGN RUN Heat/AC/ Compass Sensor ENG ASD Relay Feed Power Sunroof Feed

Heated Mirror (If Equipped) ENG ASD Relay Feed IGN RUN Only ORC Feed

396 MAINTAINING YOUR VEHICLE

Mini- Fuse 10 Amp Red

20 Amp Yellow 10 Amp Red

10 Amp Red

Cavity Cartridge

Fuse

28

29

30

31

32

33

34

35

30 Amp Pink

30 Amp Pink 40 Amp Green

Description

Cavity Cartridge

IGN RUN ORC/OCM Feed Hot Car (No Fuse Re- quired) Heated Seats

36

37

Fuse 30 Amp Pink

Mini- Fuse

Description

Headlamp/Washer Control/Smart Glass (If Equipped) Diesel Fuel Heater — If Equipped

25 Amp Natural

Headlamp Washer Relay Control (If Equipped) ENG ASD Control Feed 1
ABS MOD/J1962
Conn/PCM ABS Valve Feed

ABS Pump Feed

CAUTION!

• When installing the IPM cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the IPM, and possibly result in an electrical system failure.

(Continued)

CAUTION! (Continued)

• When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.

VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • Disengage the mini-fuse in the Power Distribution • Disconnect the negative cable from the battery.

Center labeled IOD (Ignition Off-Draw).

MAINTAINING YOUR VEHICLE 397

REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.

LIGHT BULBS — Interior Bulb Number Front Header Lamp . . . . . . . . . . . . . . . . . . . . . . T578
Center Dome Lamp . . . . . . . . . . . . . . . . . . . . . . T578
Rear Cargo/Flashlight . . . . . . . . . . . . . . . . . 8–A35LF

LIGHTS BULBS — Exterior Bulb No. Low Beam/High Beam Headlight . . . . . . . . . . . . H13
Front Park/Turn Signal/Side Marker Light . . . . . . . . . . . . . . . . . . . . . . . 3157AK or 3157A Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . 9145
Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . LED Assembly Rear Tail/Turn/Stop . . . . . . . . . . . . . . . . . . . . . 3157
Backup Light . . . . . . . . . . . . . . . . . . . . . W16W (921) License Light . . . . . . . . . . . . . . . . . . . . . . . . . . W5W Off-Road Light. . . . . . . . . . . . . . . . . . . . . . . . . . . H3

398 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT

Headlamps

1. Raise the hood and locate the connector behind the headlight.

2. Reach into engine compartment and pull red lock out at connector.

3. Remove the green connector from the back of the bulb by pulling straight back.

4. Twist the bulb to the left.

MAINTAINING YOUR VEHICLE 399

400 MAINTAINING YOUR VEHICLE

5. Pull bulb outward from assembly.

Fog Lights See your authorized dealer for replacement. Tail Lights, Rear Turn Signals And Backup Lights

1. Remove the two push-pins from the tail light housing. 2. Grasp the tail light and pull firmly to disengage the light from the aperture panel. 3. Twist and remove socket from the light. 4. Remove bulb from socket and replace.

NOTE: These are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life.

License Lights

2. Rotate the socket 1/4 turn counterclockwise.

MAINTAINING YOUR VEHICLE 401

1. Use a screw driver to gently pry against the side of the snap tab to remove the light from the liftgate.

402 MAINTAINING YOUR VEHICLE

3. Pull the bulb from the socket.

Auxiliary Off-Road Light

1. Remove the three screws attaching the lens to the housing.

Center High-Mounted Stoplight Light is an LED assembly. See your authorized dealer for replacement.

2. Unlatch the wire clasp securing the bulb into the housing and rotate it into the position shown.

3. Disconnect the bulb from the light harness to replace the bulb.

MAINTAINING YOUR VEHICLE 403

404 MAINTAINING YOUR VEHICLE

FLUIDS AND CAPACITIES

Fuel (Approximate) Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, API Certified) Cooling System * 2.0L and 2.4L Engine (MOPAR威 Engine Coolant/Antifreeze 5
Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level.

U.S.

13.6 Gallons

4.5 Quarts

7.2 Quarts

Metric

51.5 Liters

4.26 Liters

6.8 Liters

FLUIDS, LUBRICANTS, AND GENUINE PARTS

MAINTAINING YOUR VEHICLE 405

Engine Component Engine Coolant

Engine Oil

Engine Oil Filter Spark Plugs Fuel Selection

Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. MOPAR威 Oil Filter (P/N 04884900AB) or equivalent ZFR5F-11 (Gap 0.043 in [1.1 mm]) 87 Octane

406 MAINTAINING YOUR VEHICLE

Chassis Component Automatic Transaxle (CVT) Manual Transaxle Rear Drive Assembly (RDA)

Power Transfer Unit (PTU)

Brake Master Cylinder

Power Steering Reservoir

Fluid, Lubricant, or Genuine Part MOPAR威 CVTF + 4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non- synthetic product. MOPAR威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non- synthetic product. MOPAR威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent. MOPAR威 Power Steering Fluid +4 or ATF+4 Automatic Transmission Fluid.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emissions Control System Maintenance . . . . . . 408
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 408

▫ Required Maintenance Intervals . . . . . . . . . . 410

M

408 MAINTENANCE SCHEDULES

EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.

Information Center

MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles, “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles, “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation condition, the oil change indicator message will illuminate; this means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change and even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first.

vehicle off-road for an extended period of time.

Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If this scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Oil Change Required” in “Use Factory Settings” of the EVIC section

MAINTENANCE SCHEDULES 409

in this manual or under “Odometer/Trip Odometer” in the Instrument Cluster Descriptions section of this manual. At Each Stop for Fuel • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if

required.

410 MAINTENANCE SCHEDULES

damage.

Once a Month • Check the tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • Check all lights and other electrical items for correct

as required.

operation.

At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Check the manual transmission fluid level.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 411

12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Inspect exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or 12 months.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ M

412 MAINTENANCE SCHEDULES

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter.

Replace the spark plugs (except 2.4L PZEV).

❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes.

MAINTENANCE SCHEDULES 413

36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

filter.

❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Odometer Reading

Date

Odometer Reading

Date

Odometer Reading

Repair Order #

Dealer Code

Repair Order #

Dealer Code

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ M

414 MAINTENANCE SCHEDULES

48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

❏ Change the manual transmission fluid if using your vehicle for any of the following: trailer

towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained speeds during hot weather, above 90°F (32°C).

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.

Inspect the brake linings; replace if necessary.

❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes. ❏ Replace the air conditioning filter.

Replace the spark plugs (except 2.4L PZEV).

❏ Replace rear drive assembly (RDA) fluid. ❏ Replace power transfer unit (PTU) fluid. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the

following: police, taxi, fleet, or frequent trailer towing. Flush and replace the engine coolant at 60 months if not done at 102,000 miles (170 000 km).

MAINTENANCE SCHEDULES 415

66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ M

416 MAINTENANCE SCHEDULES

72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter.

Replace the spark plugs (except 2.4L PZEV). Inspect and replace PCV valve if necessary. †

❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes.

Odometer Reading

Date

Odometer Reading

Repair Order #

Dealer Code

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 417

❏ ❏ ❏ ❏ M

418 MAINTENANCE SCHEDULES

96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

❏ Change the manual transmission fluid if using your vehicle for any of the following: trailer

towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained speeds during hot weather, above 90°F (32°C).

102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Flush and replace the engine coolant. Replace the spark plugs (2.4L PZEV). Flush and replace the engine coolant if not done at 60 months.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

filter.

❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Odometer Reading

Date

Odometer Reading

Repair Order #

Dealer Code

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 419

❏ ❏ M

420 MAINTENANCE SCHEDULES

120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter.

Inspect the brake linings; replace if necessary.

❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes. ❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary. Replace the spark plugs (except 2.4L PZEV).

❏ Replace rear drive assembly (RDA) fluid. ❏ Replace power transfer unit (PTU) fluid. ❏ Change the automatic transmission fluid and filter. ❏ Replace the accessory drive belt(s).

126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

filter.

❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Odometer Reading

Date

Odometer Reading

Repair Order #

Dealer Code

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 421

❏ ❏ M

422 MAINTENANCE SCHEDULES

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.

If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.

❏ Replace the air conditioning filter.

Inspect the CV joints. Inspect exhaust system. Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

❏ Change the manual transmission fluid if using your vehicle for any of the following: trailer

towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained speeds during hot weather, above 90°F (32°C).

150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter.

Replace the spark plugs (except 2.4L PZEV).

❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

❏ ❏ ❏ ❏ ❏ ❏ † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty.

MAINTENANCE SCHEDULES 423

WARNING!

You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.

IF YOU NEED CONSUMER ASSISTANCE

CONTENTS

䡵 Suggestions For Obtaining Service For Your

Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
▫ Prepare For The Appointment . . . . . . . . . . . . 427
▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . 427
▫ Be Reasonable With Requests . . . . . . . . . . . . 427
䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . 427
▫ Chrysler LLC Customer Center . . . . . . . . . . . 428
▫ Chrysler Canada Inc. Customer Center . . . . . 428
▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . 428

▫ Customer Assistance For The Hearing Or

▫ Service Contract

Speech Impaired (TDD/TTY) . . . . . . . . . . . . 429
. . . . . . . . . . . . . . . . . . . . . 429
䡵 Warranty Information (U.S. Vehicles Only) . . . . 430
䡵 MOPAR威 Parts . . . . . . . . . . . . . . . . . . . . . . . 430
䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 430

▫ In The 50 United States And Washington,

D.C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 431

426 IF YOU NEED CONSUMER ASSISTANCE

䡵 Publication Order Forms . . . . . . . . . . . . . . . . . 431
䡵 Department Of Transportation Uniform Tire

Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 432
▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 433

▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 433
▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 434

SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE

Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem. Prepare A List Make a written list of your vehicle’s problems or the specific work you want done. If you’ve had an accident or work done that is not on your maintenance log, let the service advisor know. Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with

IF YOU NEED CONSUMER ASSISTANCE 427

the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.

IF YOU NEED ASSISTANCE The manufacturer and its authorized dealers are vitally interested in your satisfaction. We want you to be happy with our products and services. Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know you and the vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.

428 IF YOU NEED CONSUMER ASSISTANCE

This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.

Any communication to the manufacturer’s customer cen- ter should include the following information: • Owner’s name and address • Owner’s telephone number (home and office) • Authorized dealership name • Vehicle Identification Number (VIN)

• Vehicle delivery date and mileage Chrysler LLC Customer Center P.O. Box 21–8004