2010 Jeep Liberty Owners Manual

R-134a air conditioning refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental

MAINTAINING YOUR VEHICLE 437
Protection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by an authorized dealer or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compres- sor Oil, and Refrigerants. A/C Air Filter – If Equipped Refer to “Maintenance Schedule” for further information.

WARNING!

Do not remove the A/C Air Filter while the blower is operating or personal injury may result.

Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate,

438 MAINTAINING YOUR VEHICLE tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease, such as MOPAR威 Spray White Lube or equivalent, to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as MOPAR威 Lock Cylinder Lubricant or equivalent, directly into the lock cylinder.

Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner or use the washer solvent. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any condition is

present please proceed to clean wiper blades with humid cloth removing any debris that may be affecting its function. Adding Washer Fluid The windshield and rear window washers share the same fluid reservoir. The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or

MAINTAINING YOUR VEHICLE 439
exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.

WARNING!

Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.

Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system or if the exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged,

440 MAINTAINING YOUR VEHICLE have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required.

WARNING!

Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further informa- tion.

CAUTION!

The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine.

Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.

MAINTAINING YOUR VEHICLE 441

CAUTION!

WARNING!

Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.

NOTE: systems can result against you.

Intentional tampering with emissions control in civil penalties being assessed

A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.

In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, safely bring the vehicle to a complete stop, turn off the engine, and allow it to cool. Service, including a tune up to manufacturer’s specifications, should be obtained imme- diately.

442 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any ignition coil connec- • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating condi- tions.

tors disconnected for prolonged periods.

vehicle.

• Do not allow vehicle to run out of fuel.

Cooling System

WARNING!

• You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.

Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser (if equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently

spraying water from a garden hose vertically down the face of the A/C condenser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.

MAINTAINING YOUR VEHICLE 443

Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to “Maintenance Schedule” for further information. Selection of Engine Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts” in “Maintaining Your Vehicle” for further information.

444 MAINTAINING YOUR VEHICLE

CAUTION!

• Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator.

(Continued)

CAUTION! (Continued)

• This vehicle has not been designed for use with Propylene Glycol based engine coolant (anti- freeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended.

Adding Engine Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).

When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Anti- freeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.

Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.

MAINTAINING YOUR VEHICLE 445
NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to ensure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.

446 MAINTAINING YOUR VEHICLE

WARNING!

• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.

Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal

rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing engine coolant (anti- freeze). Advise your service attendant of this. As long as

the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant bottle.

MAINTAINING YOUR VEHICLE 447

• Check coolant freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • Make sure that the radiator and coolant recovery • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean.

bottle hoses are not kinked or obstructed.

448 MAINTAINING YOUR VEHICLE

• Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions.

Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” for further information.

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.

Brake Master Cylinder The fluid in the master cylinder should be checked when performing under hood services or immediately if the “Brake Warning Light” is illuminated. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.

WARNING!

• Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further informa- tion. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir. • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.

(Continued)

MAINTAINING YOUR VEHICLE 449

WARNING! (Continued)

• Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces. • Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident.

Automatic Transmission

Fluid Level Check Your vehicle is equipped with a capped transmission oil fill tube that is sealed and it should not be tampered with. Your authorized dealer has the proper tools to ensure that the fluid level is set properly.

450 MAINTAINING YOUR VEHICLE

CAUTION!

Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.

Fluid and Filter Changes Refer to “Maintenance Schedule” for further information. In addition, change the fluid and filter if the transmission is disassembled for any reason.

Special Additives The manufacturer strongly recommends against the ad- dition of any additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission sealers should be avoided as they may adversely affect seals.

CAUTION!

Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Vehicle Limited Warranty.

Transfer Case

Fluid Level Check The fluid level should be to the bottom edge of the fill hole (1) when the vehicle is in a level position.

MAINTAINING YOUR VEHICLE 451

Draining Fluid First remove the fill plug (1), then the drain plug (2). Recommended tightening torque for the drain and fill plugs is 15–25 ft lbs (20–34 N·m).

CAUTION!

Do not over-tighten the plugs. You could damage them and cause a leak.

Lubricant Selection Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.

1 — Fill Plug 2 — Drain Plug Adding Fluid Fluid should be added only to fill hole until fluid begins to run out of the hole.

452 MAINTAINING YOUR VEHICLE Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the fluid becomes contaminated with water. Change the fluid immediately if contaminated with water. Front/Rear Axle Fluid

Fluid Level Check The lubricant level should be at bottom edge of the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above. Lubricant Selection Use only manufacturer’s recommended lubricant. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintain- ing Your Vehicle” for further information.

Frequency of Fluid Change Under normal operating conditions, the lubricant in- stalled at the factory will give satisfactory lubrication for the life of the vehicle. Lubricant changes are not neces- sary unless the lubricant becomes contaminated with water. Change the lubricant immediately if contaminated with water. Sky Slider™ Top Care Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleaning easier. Do not subject the top to excessive heat. Frequently vacuum the top and tracks. Periodically wipe dust and dirt from the top and inside of the tracks by hand with an alcohol dampened cloth. Washing Hand washing or an automatic car wash with a soft cloth system is preferred.

CAUTION!

Avoid pointing a high-pressure hand held spray wand directly at the sides of the top, as this can damage the seal and force water past the weather strips.

General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles. If hand washing: • Wash in partial shade instead of direct sun. • Wet the entire vehicle before washing the top. • Wash the top with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dish washing soap. Do not use detergent.

MAINTAINING YOUR VEHICLE 453

square feet at a time. Avoid heavy scrubbing.

• Scrub in all directions, covering an area of about two • Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces. • Allow the top to dry before opening. Vacuuming the top with a wet/dry shop vacuum will decrease the tops drying time, ensure removal of all dirt, and delete streaks in the material. • Multiple cleanings may be necessary to remove stub- born stains. If stains persist, contact your local autho- rized dealership for further suggestions.

454 MAINTAINING YOUR VEHICLE

CAUTION!

Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum distillates, or plasticizers. Always wait until the top is thoroughly dry before opening it.

Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply MOPAR威 Convertible Cloth Top Cleaner or equivalent to the complete stain, extending 2 in (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy scrubbing. Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure. When the stain is no longer showing, rinse the complete top with warm water. Let the top dry before opening it.

Protection For appearance purposes, you may wish to protect the acrylic (cloth) top periodically. A fabric protectant such as Scotchguard威 is suggested. The top should be clean and dry before application of the protectant.

CAUTION!

Avoid getting Scotchguard威 on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur.

Weather Strip Care Lubricate the weather strips periodically with MOPAR威 Weather Strip Lubricant or equivalent, to keep them soft and pliable.

Appearance Care and Protection from Corrosion

Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.

MAINTAINING YOUR VEHICLE 455

The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove.

456 MAINTAINING YOUR VEHICLE

• Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax or equivalent, to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

• Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and tailgate must be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner.

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.

mud or stone shields behind each wheel.

Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent, or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 cleaners or equivalent are recommended. Do not use oven cleaner.

MAINTAINING YOUR VEHICLE 457
Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Stain Repel Fabric Cleaning Procedure – If Equipped Stain Repel seats may be cleaned in the following man- ner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.

with a clean, dry towel.

458 MAINTAINING YOUR VEHICLE

• For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of

protectants on Stain Repel products.

Interior Care

Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface.

Cleaning Interior Trim Clean interior trim with a damp cloth and MOPAR威 Total Clean or equivalent, and if necessary, follow with MO- PAR威 Spot & Stain Remover or equivalent. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery. Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recom- mended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean

leather upholstery. Application of a leather conditioner is not required to maintain the original condition.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.

Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.

MAINTAINING YOUR VEHICLE 459
Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments, which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.

460 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat Belt Maintenance Do not bleach, dye, or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.

If the seat belts need cleaning, use a mild soap solution or lukewarm water. Dry with a soft cloth. Do not remove the seat belts from the car to wash them. Replace the seat belts if they appear frayed or worn or if the buckles do not work properly.

FUSES

Totally Integrated Power Module (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. This center contains cartridge fuses, mini-fuses and relays. A label that identifies each component is printed on the inside of the cover.

J3

J4

J5

J6

J7

J8

J9

Totally Integrated Power Module (TIPM)

Cavity Cartridge

Fuse

Mini- Fuse

J1
J2

— 30 Amp Pink

— —

Description

— Transfer Case Module – If Equipped

Cavity Cartridge

MAINTAINING YOUR VEHICLE 461

Mini- Fuse

Description

—

—

—

—

—

—

—

Rear Door Modules

Driver Door Node

Passenger Door Node

Anti-Lock Brake System (ABS) Pump/ ESP – If Equipped Anti-Lock Brake System (ABS) Valve/ ESP – If Equipped Power Seats – If Equipped PZEV/Flex Fuel – If Equipped

Fuse 30 Amp Pink 25 Amp Natural 25 Amp Natural 40 Amp Green

30 Amp Pink

40 Amp Green 40 Amp Green

462 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Mini- Fuse

Description

Cavity Cartridge

J10

J11

J13

J14

J15

Fuse 30 Amp Pink

30 Amp Pink

60 Amp Yellow 40 Amp Green

30 Amp Pink

—

—

—

—

—

Headlamp Wash Relay – If Equipped/ Man Tuning Valve – If Equipped Sway Bar – If Equipped/Thatchm Lk-Ulk – If Equipped/Pwr Sld Dr Mod – If Equipped Ignition Off Draw (IOD) EBL (Rear Window Defogger) – If Equipped Rear Blower – If Equipped

J17

J18

J19

J20

J21

J22

M1

Fuse 40 Amp Green 20 Amp Blue

60 Amp Yellow 30 Amp Pink 20 Amp Blue 25 Amp Natural —

Mini- Fuse

—

—

—

—

—

—

15 Amp Blue

Description

Starter Solenoid

Powertrain Control Module (PCM) Transmission Relay Radiator Fan

Front Wiper

Front Washer/Rear Washer – If Equipped Sunroof Module – If Equipped Stop Light Switch Feed — Center High Mounted Stop Light (CHMSL)

Cavity Cartridge

Fuse

M2

M3

M4

M5

M6

M7

M8

—

—

—

—

—

—

—

Mini- Fuse 20 Amp Yellow 20 Amp Yellow 10 Amp Red 25 Amp Natural 20 Amp Yellow

20 Amp Yellow 20 Amp Yellow

Description

Cavity Cartridge

Fuse

M9

M10

M11

M12

—

—

—

—

Trailer Lighting – If Equipped Frt/Rr Axle Lockers – If Equipped Trailer Tow – If Equipped Power Inverter – If Equipped Power Outlet #1
(Cigar Lighter)/Rain Sensor – If Equipped/ Trailer Tow – If Equipped Power Outlet #2
(BATT/ACC SELECT) Front Heated Seats – If Equipped

MAINTAINING YOUR VEHICLE 463

Mini- Fuse 20 Amp Yellow 15 Amp Blue

10 Amp Red

30 Amp Green

Description

Rr Heated Seat – If Equipped Hands-Free Module (HFM) – If Equipped/ Universal Garage Door Opener (UGDO) – If Equipped/Vanity Light Automatic Tempera- ture Control (ATC) – If Equipped Radio/Amplifier – If Equipped

464 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse

M13

—

Mini- Fuse 20 Amp Yellow

M14

—

20 Amp Yellow

Description

Cabin Compartment Node (CCN)/Wireless Control Module (WCM)/ Multifunction Control Switch Trailer Tow (BUX) – If Equipped

Cavity Cartridge

Fuse

M15

—

Mini- Fuse 20 Amp Yellow

M16

—

10 Amp Red

Description

Multifunction Control Switch/Cabin Compartment Node (CCN)/Steering Col- umn Control Module (SCM)/Rear View Mirror/Tire Pressure Monitor (TPM) – If Equipped/IR Sensor – If Equipped/Transfer Case Module – If Equipped Occupant Restraint Controller (ORC)

Cavity Cartridge

Fuse

M17

—

M18

—

M19

—

Mini- Fuse 15 Amp Blue

15 Amp Blue

25 Amp Natural

Description

Exterior Lighting – Left Front Park and Side Marker, Left Tail and Running, License Lights Exterior Lighting – Right Front Park and Side Marker, Right Tail and Running Lights Auto Shut Down (ASD) #1 and #2

MAINTAINING YOUR VEHICLE 465

Cavity Cartridge

Fuse

M20

—

Mini- Fuse 15 Amp Blue

M21

M22

M23

M24

—

—

—

—

20 Amp Yellow 10 Amp Red 10 Amp Red 25 Amp Natural

Description

Interior Lighting/ Steering Wheel Switches – If Equipped/Switch Bank/Electronic Vehicle Information Center (EVIC) – If Equipped Auto Shut Down (ASD) #3
Right Horn (Hi/Low)

Left Horn (Hi/Low)

Rear Wiper – If Equipped

466 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse

M25

M26

M27

M28

M29

M30

—

—

—

—

—

—

Mini- Fuse 20 Amp Yellow 10 Amp Red

10 Amp Red

10 Amp Red 10 Amp Red 15 Amp Blue

Description

Fuel Pump

Power Mirror Switch/ Driver Window Switch Ignition Switch/ Wireless Control Module (WCM)/ Steering Column Lock – If Equipped Powertrain Control Module (PCM) Occupant Classifica- tion Module (OCM) Rear Wiper Module – If Equipped/ Diagnostic Link

Cavity Cartridge

Fuse

M31

M32

M33

M34

M35

M36

—

—

—

—

—

—

Mini- Fuse 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red

10 Amp Red 20 Amp Yellow

Description

Back-Up Lights

Occupant Restraint Controller (ORC) Powertrain Control Module (PCM) Park Assist Module – If Equipped/Heating, Ventilation, and Air Conditioning (HVAC) Module – If Equipped/Compass Module – If Equipped Heated Mirrors – If Equipped Power Outlet #3
(BATT)

MAINTAINING YOUR VEHICLE 467

Cavity Cartridge

Fuse

M37

—

M38

—

Mini- Fuse 10 Amp Red

25 Amp Natural

Description

Anti-Lock Brake Sys- tem (ABS)/Electronic Stability Program (ESP) Module/Stop Light Switch Door and Liftgate Lock/Unlock Motors

CAUTION! (Continued)

• When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.

CAUTION!

• When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in an electrical system failure.

(Continued)

REPLACEMENT BULBS

LIGHT BULBS – Interior Bulb No. Cargo Lamp. . . . . . . . . . . . . . . . . . . . . . . . . TL212–2
Overhead Console Lamp . . . . . . . . . . . . . PLW214–2A Reading Lamp . . . . . . . . . . . . . . . . . . . . . . WL212–2

468 MAINTAINING YOUR VEHICLE

LIGHT BULBS – Exterior Bulb No. Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 9008 H13
Front Park/Turn Signal Lamp. . . . . . . . . . . . . 3757AK Front Side Marker Lamp . . . . . . . . . . . . . . . . . . . 168
Back-Up Lamp . . . . . . . . . . . . . . . . . . . . . . . . 3157K Center High Mounted Stop Lamp (CHMSL) . . . . . . LED (serviced at an authorized dealer) Fog Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . H10 9145
License Plate Lamp . . . . . . . . . . . . . . . . . . . . . . . 168
Rear Tail/Stop. . . . . . . . . . . . . . . . . . . . . . . . . 3157K Rear Turn Signal Lamp . . . . . . . . . . . . . . . . . 3757AK

BULB REPLACEMENT

Headlamp

1. Open the hood. 2. Reach behind the headlamp housing to access the headlamp bulb lock ring.

3. Firmly grasp the lock ring and rotate it counterclock- wise to unlock it. 4. Remove the bulb and connector assembly from the headlamp housing. 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb.

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

6. Install the bulb and connector assembly into the headlamp housing and rotate the lock ring clockwise to lock it in place. 7. Close the hood.

Front Turn Signal and Front Side Marker Lamp

Front Fog Lamp

MAINTAINING YOUR VEHICLE 469

1. Turn the steering wheel all the way to the right to access the left front turn signal or side marker. Turn the steering wheel all the way to the left to access the right front turn signal or side marker. 2. Remove three push-pins from the wheel-well liner. 3. Gently flex the wheel-well liner forward to access the bulb. 4. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the housing. 5. Pull the bulb out of the socket and insert the replace- ment bulb. 6. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 7. Reposition the wheel-well liner and install push-pins.

the

1. Open the hood. 2. Reach behind the headlamp housing to access the bulb. 3. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the fog lamp housing. 4. Pull the bulb out of the socket and insert the replace- ment bulb.

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

470 MAINTAINING YOUR VEHICLE 5. Install the bulb and socket assembly into the into the fog lamp housing, and rotate the connector clockwise to lock it in place. 6. Close the hood. Rear Tail/Stop, Turn Signal, and Back-Up Lamp

1. Open the liftgate. 2. Remove the screws that fasten the taillamp housing to the vehicle. 3. Pull the taillamp housing straight back to separate it from the vehicle. 4. Disconnect the electrical connector.

5. Remove the two screws that fasten the back plate to the taillamp housing. 6. Separate the back plate from the taillamp housing. 7. Pull the appropriate bulb(s) out of the back plate and insert the replacement bulb(s). 8. Install the back plate and screws into the taillamp housing. 9. Connect the electrical connector. 10. Install the taillamp housing and screws. 11. Close the liftgate.

FLUID CAPACITIES

Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) Cooling System * 3.7 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5
Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.

MAINTAINING YOUR VEHICLE 471

U.S.

19.5 Gallons

5 Quarts

14 Quarts

Metric

73.8 Liters

4.7 Liters

13.3 Liters

472 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS

Engine Component Engine Coolant

Engine Oil

Engine Oil Filter Spark Plugs Fuel Selection

Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. MOPAR威 Engine Oil Filter or equivalent. ZFR6F-11G (Gap 0.043 in [1.09 mm]) 87 Octane

Chassis Component Automatic Transmission

Transfer Case

Front Axle Rear Axle Brake Master Cylinder

Power Steering Reservoir

MAINTAINING YOUR VEHICLE 473

Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. SAE 80W-90 Multi-Purpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent. MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only rec- ommended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic Trans- mission Fluid or equivalent licensed ATF+4威 product.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emissions Control System Maintenance . . . . . . 476
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 476
▫ Required Maintenance Intervals . . . . . . . . . . 478

M

476 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.

Information Center

MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions the oil change indicator message will illuminate, this means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first.

vehicle off-road for an extended period of time.

Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by

MAINTENANCE SCHEDULES 477
referring to the steps described under “Electronic Vehicle Information Center (EVIC)/Oil Change Required” in “Understanding Your Instrument Panel” or under “In- strument Cluster Description/Odometer/Trip Odom- eter” in “Understanding Your Instrument Panel” for further information. At Each Stop for Fuel • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if

required.

M

damage.

478 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of the coolant reservoir and • Check all lights and other electrical items for correct

brake master cylinder, and add as needed.

as required.

operation.

At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.

CAUTION!

may result in damage to the vehicle.

• Failure to perform the required maintenance items • Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumfer- ence on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedule should be followed to balance tire wear.

Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 479

12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

480 MAINTENANCE SCHEDULES

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Inspect the front and rear axle fluid;

change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 481

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (3.7L Engine). ❏ Adjust parking brake on vehicles

equipped with four-wheel disc brakes.

❏ Inspect the transfer case fluid.

36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet,

off-road or frequent trailer towing.

❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

482 MAINTENANCE SCHEDULES

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Inspect the front and rear axle fluid;

change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 483

M

484 MAINTENANCE SCHEDULES

60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏ Replace the spark plugs (3.7L Engine). ❏ Inspect the brake linings; replace if necessary. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing. ❏ Change the transfer case fluid if using your vehicle for any of the following: police, taxi, fleet, off-road or frequent trailer towing. ❏ Flush and replace the engine coolant at 60 months if not done at 102,000 miles (170 000 km). ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;

replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 485

72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet,

off-road or frequent trailer towing.

❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

486 MAINTENANCE SCHEDULES

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the