2008 Jeep Liberty Owners Manual

within 5 seconds. The EVIC, if equipped, will display which memory position is being set.

128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: † For vehicles equipped with an automatic transmission, memory profiles can be set without the vehicle in “P” (Park), but the vehicle must be in “P” (Park) to recall a memory profile. † For vehicles equipped with a manual transmission, the vehicle speed must be at 0 mph (0 km/h) to recall a memory profile. † The Recall Memory with Remote Key Unlock feature can be turned on and off if equipped. For details, refer to “Personal Settings (Cus- tomer Programmable Features)” under “Electronic Ve- hicle Information Center (EVIC)” in Section 4 of this manual.

through the EVIC,

Linking & Unlinking the Remote Keyless (RKE) Transmitter to the Memory Feature Your Remote Keyless Entry (RKE) transmitters can be programmed to recall one of two pre-programmed memory profiles with a press of the Unlock button on the RKE Transmitter. To program your transmitters, perform the following: 1. Remove the key from ignition. 2. Select the desired memory profile 1 or 2. 3. Press and release the Set (S) button on the memory switch, then press and release the side of the rocker switch labeled 1 or 2 accordingly. 9Memory Profile Set” (1
or 2) will display in the EVIC, if equipped. 4. Press and release the Lock button on the transmitter within 10 seconds.

NOTE: Your transmitters can be unlinked to the memory setting by pressing the Set (S) button followed by the Unlock button on the transmitter in Step 4 above. Memory Position Recall NOTE: † For vehicles equipped with an automatic transmission, the vehicle must be in “P” (Park) to recall memory positions. If a recall is attempted when the vehicle is not in “P” (Park), a message will display in the EVIC, if equipped. † For vehicles equipped with a manual transmission, the vehicle speed must be at 0 mph (0 km/h) to recall memory positions. If a recall is attempted with the vehicle speed above 0 mph (0 km/h), a message will display in the EVIC, if equipped.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129

To recall the memory settings for driver one, press memory button number 1 or the Unlock button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 or the Unlock button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons (S, 1, or 2) during a recall. When a recall is cancelled, the driver seat and side mirrors will stop moving. A delay of one second will occur before another recall can be selected. Easy Entry/Exit Seat (Available with Memory Seat Only) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.

130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. † When you remove the key from the ignition switch, the driver seat will move about 2.4 inches (60 mm) rearward if the driver seat position is greater than or equal to 3.5 inches (90 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. † When you remove the key from the ignition switch, the driver seat will move to a position 1.2 inches (30
mm) forward of the rear stop if the driver seat position is between 2.4 inches and 3.5 inches (60 mm and 90
mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position.

† The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 2.4 inches (60 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry.

Each stored memory setting will have an associated Easy Entry and Easy Exit position. NOTE: The Easy Entry/Easy Exit feature can be turned on or off through the programmable features in the EVIC. For details, refer to “Automatically Move Seat Back on Exit,” under “Personal Settings (Customer Program- mable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.

TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131

Next, locate the safety latch lever between the grille and hood opening (left of center when facing hood). Push the safety latch lever to the right and then raise the hood.

Hood Release

Underhood Safety Latch

132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood.

Hood Prop Rod Hole Location

fully seated into its storage retaining clips.

To prevent possible damage: † Before closing hood, make sure the hood prop rod is † Do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.

LIGHTS

Exterior & Interior Lighting Control

The Multi-Function Control Lever on the left side of the steering column controls the operation of the headlights, parking lights, turn signal lights, instrument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped). Headlights & Parking Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133

Headlight Switch

134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Automatic Headlights — If Equipped This system automatically turns the headlights ON or OFF according to ambient light levels. To turn the system ON, turn the end of the Multi-Function Control Lever to the (A) AUTO position (third detent). When the system is ON, the Headlight Time Delay feature is also ON. This means the headlights will stay ON for up to 90 seconds after you turn the ignition switch to the LOCK position. To turn the Automatic System OFF, turn the end of the Multi-Function Control Lever out of the (A) position. NOTE: The engine must be running before the head- lights will turn ON in the Automatic mode. Headlights with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn ON approximately 10 seconds after the wipers are turned on if the Multi-Function Control Lever is placed in the (A)

AUTO position. In addition, the headlights will turn OFF when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to ”Headlights On with Wipers,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle In- formation Center” in Section 4 of this manual. Headlight Time Delay — If Equipped This feature is particularly useful when exiting your vehicle in an unlit area. It provides the safety of headlight illumination for about 90 seconds after turning the igni- tion switch to the LOCK position. To activate the delay, turn the ignition switch to the LOCK position while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay

interval begins when you turn off the headlights. Only the headlights will illuminate during this time. If you turn the headlights, or parking lights, or ignition switch on again, the system will cancel the delay. If you turn the headlights off before the ignition, they will turn off in the normal manner. The Headlight delay time is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to “Delay Turning Headlights Off,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

Daytime Running Lights (DRL) — If Equipped The high beam headlights will turn on as Daytime Running Lights (DRL) and operate at DRL (lower) inten- sity, whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the selector lever is in any position except “P” (Park). NOTE: The Daytime Running Lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned to the LOCK position, a chime will sound to alert the driver when the driver’s door is opened.

136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Fog Lights — If Equipped

To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out on the end of the Multi-Function Control Lever.

Turn Signals Move the Multi-Function Lever upward or downward and the corresponding turn signal indicator on the in- strument panel will flash to show proper operation of the front and rear turn signal lights.

Front Fog Light Control

NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights.

Turn Signal Control

You can signal a lane change by moving the lever upward or downward partially without moving beyond the de- tent. If either turn signal indicator has a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, see your autho- rized dealer for service. Highbeam/Lowbeam Select Switch Push the Multi-Function Control Lever away from you to switch the headlights to HIGH beam. Pull the Lever toward you, to switch the headlights back to LOW beam.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

Highbeam Functions

Flash to Pass You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.

138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If the Multi-Function Control Lever is held in NOTE: the Flash to Pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds before activating the Flash to Pass function again. Interior Lights

Map/Reading Lights These lights are mounted between the sun visors on the overhead console and above the rear doors by the grab handles. Each light is turned ON by pressing the lens. Press the lens a second time to turn OFF the light. These lights also turn on when a door is opened, or when the Unlock button on the Remote Keyless Entry (RKE) trans- mitter is pressed, or when the Dimmer Control is turned completely upward to the second detent.

Cargo Light The cargo light is mounted in the headliner above the rear cargo area. This light will turn on when you open the liftgate or any door, or if you press the Unlock button on the Remote Keyless Entry (RKE) transmitter, or rotate the Dimmer Control on the Multi-Function Control Lever completely upward to the second detent. Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. Dimmer Control The Dimmer Control is part of the Multi-Function Con- trol Lever. It controls the operation of the interior lights and the brightness of the instrument panel lights.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139

Parade Mode (Daytime Brightness Feature) Rotate the Dimmer Control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light ON Rotate the Dimmer Control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Interior Light Defeat OFF Rotate the Dimmer Control completely downward to the (O) OFF position. The interior lights will remain off when the doors are open.

Dimmer Control

Instrument Panel Dimming With the parking lights or headlights on, rotate the Dimmer Control upward or downward to change the brightness of the instrument panel lights.

140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WINDSHIELD WIPERS AND WASHERS

The Windshield Wiper / Washer Control Lever is located on the right side of the steering column.

Rotate the end of the lever to the first detent past the intermittent settings for Low-speed wiper operation, or to the second detent past the intermittent settings for High-speed wiper operation. NOTE: The wipers will automatically return to the “Park” position if you turn off the ignition switch while they are operating. The wipers will resume operation when you turn the ignition switch to the ON position again.

Windshield Wiper/Washer Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141

Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the Wind- shield Wiper / Washer Control Lever to the first detent, and then turn the end of the lever to select the desired delay interval. There are five delay settings, which allow you to regulate the wipe interval from a minimum of two cycles every second to a maximum of approximately 36
seconds between cycles or from a minimum of one cycle every second to a maximum of approximately 18 seconds between cycles at vehicle speeds greater than 10 mph (16
km/h).

CAUTION!

† Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than OFF. † In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. † Always remove any buildup of snow that prevents the windshield wiper blades from returning to the OFF position. If the windshield wiper control is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur.

142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

Mist Feature Push downward on the Windshield Wiper / Washer Control Lever to activate a single wipe cycle to clear the windshield of road mist or spray from a passing vehicle. The wipers will continue to operate until you release the lever.

Mist Control

Headlights with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn ON approximately 10 seconds after the wipers are turned on if the Multi-Function Control Lever (on the left side of the steering column) is placed in the (A) AUTO position. In addition, the headlights will turn OFF when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to ”Headlights On with Wipers,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle In- formation Center” in Section 4 of this manual.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143

Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or over spray from the windshield washers of the vehicle ahead. Rotate the end of the Windshield Wiper / Washer Control Lever to one of the five intermittent wiper settings to activate this feature. The sensitivity of the system is adjustable from the Windshield Wiper / Washer Control Lever. Wiper delay position 1 is the least sensitive and wiper delay position 5 is the most sensitive. Choose position 3 or 4 for normal rain conditions. Choose position 2 or 1 if you desire less wiper sensitivity. Choose position 5 if you desire more sensitivity. Place the lever in the OFF position when not using the system.

144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

wiper speed is in the LOW or HIGH position.

NOTE: † The rain-sensing feature will not operate when the † The rain-sensing feature may not function properly when ice or dried salt water is present on the wind- shield. † Use of Rain-Xt or products containing wax or silicone † The Rain Sense feature can be turned on and off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.

may reduce rain sensor performance.

The rain sensing system has protective features for the wiper blades and arms. It will not operate under the following conditions:

† Low Temperature Wipe Inhibit — The rain-sensing feature will not operate when the ignition is first switched ON, and the vehicle is stationary, and the outside temperature is below 32° F (0° C), unless the wiper control is moved, or the vehicle speed becomes greater than 0 mph (0 km/h), or the outside tempera- ture rises above freezing. † Neutral Wipe Inhibit — The rain-sensing feature will not operate when the ignition is ON, and the trans- mission selector lever is in the “N” (Neutral) position, and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control is moved or the selector lever is moved out of the “N” (Neutral) position. † Remote Start Wipe Inhibit (Vehicles Equipped with Remote Start System) — The rain-sensing feature will not operate when the vehicle is in remote start mode. This feature will return to normal operation once

remote start mode is exited. Refer to “Remote Start System” in Section 2 of this manual for information on remote start operation.

Windshield Washers To use the washer, pull the Windshield Wiper / Washer Control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the wiper control is in the OFF position, the wipers will operate for two wipe cycles and then turn OFF.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145

Adding Washer Fluid

NOTE: Refer to the “Engine Compartment” diagram in Section 7 for the location of the washer fluid reservoir. The fluid reservoir for the windshield washers is located in the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.

WARNING!

Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.

146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt control handle is located below the steering wheel at the end of the steering column.

To unlock the steering column, push the control handle downward. To tilt the steering column, move the steering wheel upward or downward as desired. To lock the steering column in position, pull the control handle upward until fully engaged.

WARNING!

Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjust- ing the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). Electronic Speed Control Operation The speed control lever is located on the right side of the steering wheel.

Speed Control Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147

To Activate:

Push and release the (“ON/OFF”) button lo- cated on the end of the speed control lever. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push and release the (“ON/OFF”) button a second time. The CRUISE indicator will turn off. Be sure to turn the system OFF when not in use. NOTE: † The Electronic Speed Control System will automati- † The Electronic Speed Control System is designed to shut down if you operate multiple speed control switch-functions simultaneously (i.e. SET and CAN- CEL). If this occurs, push and release the (“ON/OFF”) button to reactivate the system and then reestablish the desired SET speed.

cally turn off when the engine is turned off.

148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.

To Set At A Desired Speed: When the vehicle reaches the speed desired, press down on the lever and release (“SET DECEL”). Release the accelerator and the vehicle will operate at the selected speed. NOTE: † The vehicle must be traveling at least 25 mph (40

km/h) for the speed control to set.

† The vehicle should be traveling at a steady speed and on level ground before pressing the lever (“SET DE- CEL”).

To Deactivate: A soft tap on the brake pedal, or pulling the speed control lever toward you (“CANCEL”), or normal brake or clutch pressure while slowing the vehicle will deactivate the speed control without erasing the set speed from memory. Pressing the (ON/OFF) button or turning off the ignition erases the set speed from memory. NOTE: For vehicles equipped with a manual transmis- sion, depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal.

To Resume Speed: If you deactivated the speed control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever up and release (RESUME ACCEL), and then remove your foot from the accelerator pedal. To Vary The Speed Setting: When the speed control is set, you can increase speed by pushing up and holding the lever (“RESUME ACCEL”). Release the lever when the desired speed is reached, and the new set speed will be established. Tapping (“RESUME ACCEL”) once will result in a 1 mph (2 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 3 mph (5 km/h), etc.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149

To decrease speed while the speed control is set, push down and hold the lever (“SET DECEL”). Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the (“SET DECEL”) button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without speed control.

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Vehicles equipped with a manual transmission may need to be shifted into a lower gear to climb hills without speed loss.

WARNING!

Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

REAR PARK ASSIST SYSTEM — IF EQUIPPED The Rear Park Assist System is a driver aid that senses for obstacles behind the vehicle and provides both visible and audible warnings to indicate the range of the object. System Usage Precautions NOTE: † Ensure that the rear bumper is free of dirt and debris to keep the Rear Park Assist System operating prop- erly. † Jackhammers, large trucks, and other vibrations could affect the performance of the Rear Park Assist System. † When you turn off the Rear Park Assist System, the instrument cluster will display “PARK ASSIST DIS- ABLED.” Furthermore, once you turn off the Rear Park Assist System, it remains off until you turn it on again, even if you cycle the ignition key.

† When you move the shift lever to “R” (Reverse) position and the Rear Park Assist System is turned off, a single chime will sound once per ignition cycle and the instrument cluster will display “PARK ASSIST DISABLED.” † The Rear Park Assist System, when on, will MUTE the † If a Rear Park Assist System malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “SERVICE PARK ASSIST SYS- TEM” and the LED in the Rear Park Assist switch will illuminate. If this occurs, see your authorized dealer for service.

radio when it is sounding a tone.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

CAUTION!

† The Rear Park Assist System is only a parking aid and it is unable to recognize every obstacle, in- cluding small obstacles. Parking curbs might be temporarily detected or not detected at all. Ob- stacles located above or below the sensors will not be detected when they are in close proximity. † The vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using the Rear Park Assist System. † Clean the Rear Park Assist Sensors with water, car wash soap, and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.

152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

† Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up. You are responsible for safety and must continue to pay attention to your surroundings. Fail- ure to do so can result in serious injury or death. † Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning dis- play turns the red LEDs ON. Also, the sensors could detect the ball mount and hitch ball assembly, de- pending on its size and shape, giving a false indica- tion that an obstacle is behind the vehicle.

Enabling & Disabling the System There are times when you may want to disable the Rear Park Assist System, such as when towing a trailer. Vehicles Equipped With the Electronic Vehicle Information Center (EVIC) You can turn the Rear Park Assist System on or off through the EVIC. For details, refer to “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Vehicles Equipped with Rear Park Assist Switch You can turn the Rear Park Assist System on or off by pressing the Rear Park Assist switch located the lower switch bank below the climate controls.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

Rear Park Assist Switch

Rear Park Assist Indicator

System Operation The system uses four sensors located in the rear bumper fascia to scan for obstacles up to 79 inches (200 cm) away from the rear bumper fascia. The warning display located above the rear window provides both visible and audible warnings to indicate the range of the object.

The warning display contains two sets of yellow and red LEDs, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the LEDs either through the rear view mirror or by looking at the display above the rear window.

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

When the ignition is turned to the ON position, and the system is enabled, the warning display will turn ON all of its LEDs for approximately one second. Then, the system dimly illuminates the two outer most yellow LEDs when it is detecting no obstacles.

WARNING DISPLAY DISTANCES

The Rear Park Assist System is active when the ignition is in the ON position, and the system is enabled, and the driver shifts the transmission into the “R” (Reverse) position, and the vehicle speed is less than 11 mph (18
km/h). The following chart shows the warning display operation when the system is detecting an obstacle:

DISPLAY LED

OBSTACLE DISTANCE FROM:

LED COLOR

AUDIBLE SIGNAL

1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED

REAR CORNERS

31.5 in. (80 cm) 25.5 in. (65 cm) 20 in. (50 cm) 16 in. (40 cm) 6 in. (15 cm)

REAR CENTER 79 in. (200 cm) 51 in. (130 cm) 45 in. (115 cm) 39 in. (100 cm) 33.5 in. (85 cm) 28 in. (70 cm) 20 in. (50 cm) 12 in. (30 cm)

Yellow Yellow Yellow Yellow Yellow Yellow Red Red

Sounds for 1⁄2 second

None None None None None

Intermittent Continuous

GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off your vehicle’s battery. NOTE: HomeLinkt is disabled when the Vehicle Secu- rity Alarm is active.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

WARNING!

Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance.

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death.

Programming HomeLinkT

Before You Begin If you have not trained any of the HomeLinkt buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes. It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal.

Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the hand-held transmitter away from the HomeLinkt button you wish to program. Place the hand-held transmitter 1–3 inches (3–8 cm) away from the HomeLinkt button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLinkt button and the hand-held transmitter button until the HomeLinkt indicator changes from a slow to a rapidly blinking light, then release both the HomeLinkt and hand-held transmitter buttons. Watch for the HomeLinkt indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds, or longer in rare cases. The garage door may open & close while you train.

NOTE: † Some gate operators and garage door openers may require you to replace Step #3 with procedures noted in the “Gate Operator/Canadian Programming” sec- tion. † After training a HomeLinkt channel, if the garage door does not operate with HomeLinkt and the ga- rage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.”

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

4. Press and hold the just-trained HomeLinkt button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLinkt button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with program- ming for Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button.

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open & close the door).

1 — Garage Door Opener 2 — Training Button

6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for 2 sec- onds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for 2 seconds) to complete the training. If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLinkt buttons, repeat each step for each remaining button. DO NOT erase the channels.

Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLinkt to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLinkt” Step 3 with the following: 3. Continue to press and hold the HomeLinkt button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLinkt

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLinkt.” earlier in this section. Using HomeLinkT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time.

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

that has been previously

Reprogramming a Single HomeLinkT Button To re-program a channel trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLinkt button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with PRO- GRAMMING HOMELINKt Step #2 and follow all re- maining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased.

The HomeLinkt Universal Transceiver is disabled when the Vehicle Security Alarm is active. Troubleshooting Tips If you are having trouble programming HomeLinkt, here are some of the most common solutions: † Replace the battery in the original transmitter. † Press the Learn Button on the Garage Door Opener to † Did you unplug the device for training, and remember

complete the training for Rolling Code.

to plug it back in?

If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.

General Information This device complies with FCC rules part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received including interference that may cause undesired operation NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console.

Power Sunroof Switch

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

† Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. † In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. † Do not allow small children to operate the sun- roof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.

Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully and stop automatically. This is called Express Open. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called Express Close. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the

sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof - Express Press and release the 9V9 button, and the sunroof will open to the vent position. This is called Express Vent, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize the buffeting or open any window.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time is programmable. For details, refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (Cus- tomer Programmable Features),” under “Electronic Ve- hicle Information Center (EVIC)” in Section 4 of this manual.

SKY SLIDERT FULL LENGTH OPEN ROOF The Sky Slidert is a full-length, soft-top, power-roof that opens front to rear or rear to front. Sky SliderT Usage Precautions NOTE: † The system prohibits Sky Slidert operation when † The system prohibits Sky Slidert operation at vehicle † Opening and closing the Sky Slidert consecutively without the engine running may run the battery down.

ambient temperature is at –4°F (–20°C) or lower.

speeds of 86 mph (138 km/h) or above.

CAUTION!

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

† Never attempt to open or close the Sky Slidert when it is frozen. Wait until the Sky Slidert is thawed before operating. † Opening the Sky Slidert when damp, wet, or dirty can cause stains, mildew, and damage to the soft-top material and the inside of your vehicle. Make sure the Sky Slidert is dry before opening. † Always close the Sky Slidert when leaving your vehicle so as not to leave the interior exposed to potentially damaging outdoor conditions. † Do not leave the Sky Slidert open for several weeks at a time. Close it occasionally to prevent discolora- tion in the folds of the fabric and to allow the creases to smooth out. This is especially important if the Sky Slidert was opened when not completely dry.

Failure to follow these cautions can cause damage to the Sky Slider,t vehicle contents, and the vehicle interior.

of the Sky Slidert can injure a person or animal.

† In an accident, there is a greater risk of being thrown from a vehicle with the Sky Slidert open. Always fasten your seat belt properly and make sure all passengers are properly secured too. † Before operating the Sky Slider,t make sure that no moving parts † Never place any extremities (hands, feet, etc.) near the Sky Slidert † If potential danger exists while opening or closing the Sky Slidert in Automatic Mode, press and release the switch immediately to interrupt the operation. † If potential danger exists while opening or closing the Sky Slidert in Operator Mode, release the switch immediately to interrupt the operation.

components or the roof area while operating the Sky Slider.t

† Do not allow small children to operate the Sky Slider.t † Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the Sky Slidert while operating the Power Top switch. Such entrapment may result in serious injury or death.

Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you.

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Power Top Control The Power Top switch is located between the sun visors on the overhead console.

Power Top Switch

NOTE: The Power Top switch will operate when the ignition switch is turned to the ON or ACC position, and when the accessory delay feature is active.

Opening the Sky SliderT

Using Automatic Mode Press the switch rearward and release it within 1⁄2 second and the Sky Slidert will open from the front and move automatically toward the rear of the vehicle. Press the switch forward and release it within 1⁄2 second and the Sky Slidert will open from the rear and move automatically toward the front of the vehicle. For either operation, the Sky Slidert will open fully and stop automatically unless you interrupt the operation by pressing and releasing the switch again. NOTE: You can press the switch in either direction to interrupt the operation. To resume the operation from a partially open position, press and release the switch once again.

NOTE: The Sky Slidert will not open from the front and the rear at the same time. The Sky Slidert must close fully before opening it from the opposite end. Using Operator Mode Press the switch rearward and hold it and the Sky Slidert will open from the front and move toward the rear of the vehicle. Press the switch forward and hold it and the Sky Slidert will open from the rear and move toward the front of the vehicle. For either operation, the Sky Slidert will open fully and stop automatically unless you interrupt the operation by releasing the switch. To resume the operation from a partially open position, press and hold the switch once again.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

NOTE: The Sky Slidert will not open from the front and the rear at the same time. The Sky Slidert must close fully before opening it from the opposite end. Closing the Sky SliderT

Using Automatic Mode Press and release the button in the center of the switch and the Sky Slidert will close automatically from any position. The Sky Slidert will close fully and stop auto- matically. Using Operator Mode Press the switch rearward and hold it and the Sky Slidert will move forward. Press the switch forward and hold it and the Sky Slidert will move rearward. For either operation, the Sky Slidert will close fully and stop automatically unless you interrupt the operation by releasing the switch.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To resume the operation from a partially closed position, press and hold the switch once again. Manually The Sky Slidert drive motors are mounted to the roof above the cargo lamp. In the event that your vehicle losses battery power, you can close the Sky Slidert by turning the drive gears in the appropriate motor with a 6
mm Allen wrench. To do so, you must first remove the cargo lamp from the headliner. Then, insert the wrench into the “Allen” shaped hole in the appropriate motor and turn the wrench clockwise until the top closes completely. The left motor facing forward will close the top when it is open from the rear of the vehicle. The right motor will close the top when it is open from the front of the vehicle.

Anti-Pinch Protect Feature The Sky Slidert will retract automatically if it detects an obstruction while closing. If this occurs, remove the obstruction and use the switch again to close the Sky Slider.t

WARNING!

There is no anti-pinch protection when the Sky Slidert is almost closed. Be sure to clear all objects from the Sky Slidert before closing.

Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the Sky Slidert in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear

windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the Sky Slidert open, adjust the Sky Slidert opening to minimize the buffeting or open any window. Sky SliderT Maintenance Refer to “Sky Slidert Top Care” under “Maintaining Your Vehicle” in Section 7 of this manual.

ELECTRICAL POWER OUTLET Your vehicle is equipped with a fused 12-volt power outlet. This outlet is located on the instrument panel below the climate controls. It has power available when the ignition switch is in the ON position. It can operate a conventional cigar lighter unit or power accessories designed for use with a standard power outlet adapter.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

Front Power Outlet

If desired, the instrument panel power outlet NOTE: can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Electrical Outlet Use With Engine Off

CAUTION!

† Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. † Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these intermittently and with greater caution. † After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. † Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug.

POWER INVERTER — If EQUIPPED Your vehicle may be equipped with a 115 Volt AC (150
Watt maximum) power outlet located on the back of the center console. This outlet can power small appliances and electronic devices.

115VAC (150W) Power Outlet

A control switch for the outlet is located in the lower switch bank below the climate controls.

115VAC (150W) Power Outlet Control Switch

Press and release the switch once to turn on the power outlet. A status indicator in the switch will illuminate in approximately one second to indicate that power is

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

available at the outlet. Press and release the switch again to turn off the power outlet. The status indicator will also turn off. NOTE: Due to built-in overload protection, the power outlet will shut down if the 115 Volt AC (150 Watt maximum) power rating is exceeded.

WARNING!

To Avoid Serious Injury or Death: † Do not use a 3-Prong Adaptor. † Do not insert any objects into the receptacles. † Do not touch with wet hands. † Close the lid when not in use. † If this outlet is mishandled, it may cause an

electric shock and failure.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CUP HOLDERS Front and rear cup holders are located in the center console.

Front Cup Holders

Rear Cup Holders

STORAGE

Front Storage Compartment The front storage compartment (located on the left side of the instrument panel) can hold cell phones, PDA’s, and other small items.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

Console Storage Compartment To open, press the latch and lift the cover.

Front Storage Compartment

Center Console

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The center console has a removable storage tray, which can hold cell phones, PDA’s, and other small items.

Removable Storage Tray

CARGO AREA FEATURES

Cargo Load Floor The cargo load floor system has a load capacity of 400 lbs (181 kg). The load floor has a built-in storage bin that can hold a variety of items. The underside of the storage bin cover also contains a plastic lined tray. The cover can be installed with either side facing up for added utility. To provide additional storage area, each rear seat can be folded flat. This allows for extended cargo space and still maintains some rear seating room. Refer to “Seats” in this Section for additional information on the 60/40 Split Folding Rear Seat with Fold Flat feature. Accessing the Storage Bin

NOTE: The spring-loaded latches that retain the storage bin cover to the cargo load floor should not be used as cargo tie-downs. 1. Flip the spring-loaded latch pull-loops up.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

NOTE: You can install the cover with either side facing upward. 5. With the cover seated in the floor, pull upward on loops and twist them 1⁄4 turn so that they are no longer parallel to the slots in the cover. 6. Flip the loops down.

WARNING!

A loose storage bin cover thrown forward in a colli- sion or hard stop could endanger the occupants of the vehicle. Always latch the storage bin cover to the cargo load floor with the spring-loaded latches when not accessing the storage bin.

2. Pull the loops upward and twist them 1⁄4 turn so that they are parallel to the slots in the storage bin cover. 3. Lift the cover upward over the loops. 4. When done, reinstall the cover with the handle recess facing toward you.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Cargo Tie-Down Hooks & Loops The tie-downs located on cargo area floor should be used to secure loads safely when the vehicle is moving.

NOTE: The spring-loaded latches that retain the storage bin cover to the cargo load floor should not be used as cargo tie-downs. Cargo tie-down loops are located on the trim panels.

Cargo Tie-Down Hooks

Cargo Tie-Down Loops

WARNING!

† Cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or collision, a tie-down could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. † The weight and position of cargo and passengers can change the vehicle center of gravity and ve- hicle handling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your vehicle:

† Do not carry loads that exceed the load limits de- scribed on the label attached to the left door or left door center pillar.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

† Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. † Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the vehicle to sway. † Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.

WARNING!

To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. The removable retractable cargo area cover mounts in the cargo area behind the top of the rear seats. The cover, when extended, covers the cargo area to keep items out of sight. Notches in the trim panels near the liftgate opening secure the extended cover in place. The cover rolls away neatly inside its housing when not in use. You can also remove the cover from the vehicle to make more room in the cargo area. To install the cover, position it in the vehicle so that the flat side of the housing faces upward. Then, insert either the left or the right spring-loaded post (located on the ends of the cover housing) into either of the left or the right attachment points shown.

Then, insert the spring-loaded post on the opposite end of the cover housing into the attachment point on the opposite side of the vehicle.

Next, grab the cover handle and pull the cover toward you. As the cover nears the liftgate opening, guide the rear attachment posts (on both ends of the cover) into the notches in the trim panels. Then, lower the cover to position the posts into the bottom of the notches and release the handle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

WARNING!

In an accident, a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

REAR WINDOW FEATURES

Rear Window Wiper/Washer — If Equipped

The Rear Window Wiper / Washer Control located on the right side of the steering column.

is

The rotary ring switch on the lever controls rear wiper and washer operation. Rotate the switch upward to the first detent to activate the rear wiper. Rotate the switch upward to the second detent to activate the rear washer. The washer will continue to operate until you release the switch. Once released, the wiper will cycle three times, return to the park position, and then resume normal operation. NOTE: The rear wiper will automatically return to the “Park” position if you turn off the ignition switch while it is operating. The rear wiper will resume operation when you turn the ignition switch to the ON position again.

Rear Window Wiper / Washer Control

CAUTION!

† Turn the rear wiper off when driving through an automatic car wash. Damage to the rear wiper may result if the rear wiper control is left in the ON position. † In cold weather, always turn off the rear wiper switch and allow the rear wiper to return to the park position before turning off the engine. If the rear wiper switch is left on and the rear wiper freezes to the window, damage to the rear wiper motor may occur when the vehicle is restarted. † Always remove any buildup of snow that prevents the rear wiper blade from returning to the PARK position. If the rear wiper control is turned OFF and the blade cannot return to the PARK position, damage to the rear wiper motor may occur.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

Adding Washer Fluid The windshield washer and rear window washer share the same fluid reservoir. The reservoir is located in the front of the engine compartment. Be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. Rear Window Defroster — If Equipped

The electric Rear Window Defroster Control is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illumi- nate when the rear window defroster is ON. The de- froster turns off automatically after approximately 10
minutes of operation for the first push of the button, and will turn off after approximately 5 minutes for the second push of the button.

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

† Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. † Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. † Keep all objects a safe distance from the window. Failure to follow these cautions can cause damage to the heating elements.

ROOF LUGGAGE RACK — IF EQUIPPED The load carried on the roof, when equipped with a luggage rack, must not exceed 150 lbs (68 kg), and it should be uniformly distributed over the cargo area. The tie loops provided in the side rails can be used to help tie down cargo; however, crossbars should always be used whenever cargo is placed on the roof rack. Tie loops should not be used on their own to attach luggage to the roof rack. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars are offered by Mopart accessories. External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity.

CAUTION!

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.

To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads, which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. Place a blanket or other protection between the surface of the roof and the load. Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward loads. This is espe- cially true on large flat loads and may result in damage to the cargo or your vehicle.

INSTRUMENT PANEL AND CONTROLS

CONTENTS

m Instrument Panel Features . . . . . . . . . . . . . . . . . 188
m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 189
m Instrument Cluster Descriptions . . . . . . . . . . . . 190
m Electronic Vehicle Information Center (EVIC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
N Electronic Vehicle Information Center (EVIC)

Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
N Oil Change Required . . . . . . . . . . . . . . . . . . . 209
N Trip Functions . . . . . . . . . . . . . . . . . . . . . . . 210
N Compass Display . . . . . . . . . . . . . . . . . . . . . 212

N Telephone (UConnect™) — If Equipped . . . . . 214
N Personal Settings (Customer Programmable

Features)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 216
m Radio General Information . . . . . . . . . . . . . . . . 221
N Radio Broadcast Signals . . . . . . . . . . . . . . . . . 221
N Two Types Of Signals . . . . . . . . . . . . . . . . . . 221
N Electrical Disturbances . . . . . . . . . . . . . . . . . . 221
N AM Reception . . . . . . . . . . . . . . . . . . . . . . . 221
N FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 221

186 INSTRUMENT PANEL AND CONTROLS

m Sales Code REQ — AM/FM Stereo Radio And

6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
N Operating Instructions - Radio Mode . . . . . . . 223
N Operation Instructions - (Disc Mode For CD

And MP3/WMA Audio Play, DVD-Video) . . . . 231
N Notes On Playing MP3/WMA Files . . . . . . . . 233
N List Button (Disc Mode For MP3/WMA

Play)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

N Info Button (Disc Mode For MP3/WMA

Play)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

m Sales Code RER — Multimedia System —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
N Operating Instructions — Satellite Radio . . . . . 239

N Operating Instructions — Hands-Free

Communication (UConnect™) (If Equipped)

. . 239
N Clock Setting Procedure . . . . . . . . . . . . . . . . . 239

m Sales Code RES — AM/FM Stereo Radio With

CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . . 241
N Operating Instructions - Radio Mode . . . . . . . 242
N Operation Instructions - CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 247
N Notes On Playing MP3 Files . . . . . . . . . . . . . 250
N List Button (CD Mode For MP3 Play) . . . . . . . 252
N Info Button (CD Mode For MP3 Play) . . . . . . . 252

m Satellite Radio (RSC) — If Equipped

(RER/REQ/REN Radios Only) . . . . . . . . . . . . . 254
N System Activation . . . . . . . . . . . . . . . . . . . . . 254

N Electronic Serial Number/Sirius Identification

Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 254
N Selecting Satellite Mode . . . . . . . . . . . . . . . . . 255
N Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 255
N Reception Quality . . . . . . . . . . . . . . . . . . . . . 255
N Operating Instructions - Satellite Mode . . . . . . 255
N Operating Instructions - Hands Free Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . . 258

N Operating Instructions - Video Entertainment

System (VES™) (If Equipped) . . . . . . . . . . . . . 258
m Remote Sound System Controls — If Equipped . . 258
N Right-Hand Switch Functions . . . . . . . . . . . . . 258

INSTRUMENT PANEL AND CONTROLS 187

N Left-Hand Switch Functions For Radio

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 259

N Left-Hand Switch Functions For Media

(i.e. CD) Operation . . . . . . . . . . . . . . . . . . . . 259
m CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 259
m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 260

N Manual Air Conditioning And Heating

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260

N Automatic Temperature Control (ATC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 264
N Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 270

188 INSTRUMENT PANEL AND CONTROLS

INSTRUMENT PANEL FEATURES

1 — Air Outlet 2 — Instrument Cluster 3 — Storage Tray 4 — Center Air Outlet

5 — Radio 6 — Glove Box 7 — Climate Control 8 — Power Outlet

9 — Lower Switch Bank 10 — Storage Bin* * If Equipped

INSTRUMENT CLUSTER

INSTRUMENT PANEL AND CONTROLS 189

190 INSTRUMENT PANEL AND CONTROLS

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge

The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. (See page 359
for more information.)

2. Fuel Cap Indicator

This symbol indicates the side of the vehicle where the fuel cap is located.

3. Low Fuel Warning Light

This indicator lights when the fuel level drops to approximately 1/8 tank. (See page 359 for more information.)

4. Tire Pressure Monitoring Telltale Light — If Equipped

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires are significantly under-inflated. Ac- cordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a

INSTRUMENT PANEL AND CONTROLS 191

When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replace- ment or alternate tires and wheels allow the TPMS to continue to function properly. (See page 346 for more information.)

significantly under-inflated tire causes the tire to over- heat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists.

192 INSTRUMENT PANEL AND CONTROLS

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result. (Refer to “Tire Inflation Pressures” under “Tires — General Information” and to “Tire Pressure Monitor System (TPMS)” in Section 5 of this manual for more information).

5. Electronic Throttle Control (ETC) Warning Light — If Equipped

This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected, the light will turn on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable and not need towing, however see your authorized dealer for service as soon as possible. If the light is flashing when the engine is running, you may experience power loss, an elevated/rough idle, and increased brake pedal effort, and your vehicle may require towing. Immediate service is required. The light will turn on when the ignition switch is first turned ON, and remain on briefly as a bulb check. This is normal. If the light does not turn on during starting, have the system checked by an authorized dealer.

6. Malfunction Indicator Light

This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will turn on when the key is in the ON position before engine start. If the light does not turn on when turning the key from LOCK or ACC to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may turn on the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and it will not require towing. If the Malfunction Indicator Light flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic

INSTRUMENT PANEL AND CONTROLS 193

converter damage. The vehicle should be serviced as soon as possible if this occurs. (See page 399 for more information.)

CAUTION!

Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

7. High Beam Indicator Light

This light shows that the headlights are on high beam. Pull the Multi-Function Control Lever on the left side of the steering column toward you to switch to Low beam. (See page 133 for more information.)

194 INSTRUMENT PANEL AND CONTROLS

8. Front Fog Light Indicator Light — If Equipped

This light shows when the fog lights are ON. (See page 133 for more information.)

9. Speedometer Shows the vehicle speed. 10. Turn Signal Indicator Light

The left or right arrow will flash in unison with the corresponding front and rear turn signal lights when the turn signal switch is operated. (See page 133 for more information.) NOTE: A chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. NOTE: Check for a defective outside light bulb if either indicator flashes at a rapid rate.

11. Electronic Stability Program (ESP) / Traction Control System (TCS) Indicator Light

If this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator. Be sure to adapt your speed and driving to the prevailing road conditions. (See page 314 for more infor- mation.)

12. Charging System Warning Light

This light shows the status of the electrical charg- ing system. The light should turn on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or turns on while driving, turn off some of the vehicle’s electrical devices, such as the Fog Lights or Rear Defroster. If the light remains on, it means that the charging system is experi- encing a problem. See your local authorized dealer to obtain SERVICE IMMEDIATELY.

13. Oil Pressure Warning Light

This light shows low engine oil pressure. The light will turn on and remain on when the ignition switch is turned from the LOCK or ACC position to the ON position. The light will turn off after the engine is started. If the light does not turn on during starting, have the system checked by an authorized dealer. If the light turns on and remains on while driving, safely bring the vehicle to a stop and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. This light does not show the quantity of oil in the engine. The engine oil level must be checked using the proper procedure. (See page 403 for more information.) 14. Anti-Lock Brake Warning Light

This light monitors the Anti-Lock Brake Sys- tem. This light will turn on when the ignition switch is turned to the ON position and it may stay on for approximately 3 seconds.

INSTRUMENT PANEL AND CONTROLS 195

If the light remains on or turns on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally, provided the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The ABS Warning light should be checked frequently to assure that it is operating properly. Turn the ignition switch to the ON position, but do not start the vehicle. The light should turn on. If the light does not turn on, have the system checked by an authorized dealer. (See page 310 for more information.) 15. Tachometer This gauge measures engine revolutions-per-minute (rpm x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage.

196 INSTRUMENT PANEL AND CONTROLS

16. 4 LOW Mode Indicator Light — If Equipped

This light alerts the driver that the vehicle is in the 4WD LOW mode. In this mode, the front driveshaft and rear driveshaft are mechanically locked together forcing the front and rear wheels to rotate at the same speed. (See page 292 for more information.) 17. Hill Descent Control Indicator Light — If Equipped The symbol indicates the status of the Hill Decent Control (HDC) feature. The lamp will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the “4WD Low” position and the vehicle speed is less then 30 mph. If these conditions are not met while attempting to use the HDC feature, the HDC indicator lamp will flash on/off.(See page 314 for more information.)

18. TOW / HAUL Indicator Light — If Equipped

light will

This illuminate when selecting TOW/HAUL. The TOW/HAUL button is lo- cated on the gearshift bezel. (See page 281 for more information.)

19. 4WD Indicator Light — Vehicles Equipped with Command-Tract

This light alerts the driver that the vehicle is in the four-wheel drive mode. In this mode, the front driveshaft and rear driveshaft are me- chanically locked together forcing the front and rear wheels to rotate at the same speed. (See page 292 for more information.) 20. Electronic Stability Program (ESP) / Brake Assist System (BAS) Malfunction Indicator Light – If Equipped

The malfunction indicator lamp for the ESP is combined with the BAS indicator. The yellow “ESP/BAS Warning Lamp” in the instrument

cluster comes on when the ignition switch is turned to the “ON” position. It should go out with the engine running. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light remains on after the several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.(See page 314 for more information.) NOTE: The “ESP/BAS Warning Lamp” comes on mo- mentarily each time the ignition switch is turned ON. NOTE: Each time the ignition switch is turned ON, the ESP System will be ON even if it was turned off previ- ously. NOTE: The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the

INSTRUMENT PANEL AND CONTROLS 197

sound will stop when the ESP becomes inactive following a maneuver that caused the ESP activation. 21. SERV (Service) 4WD Indicator Light — If Equipped The “SERV 4WD Indicator Light” will turn on when the ignition key is turned to the ON position and it will stay on for 2 seconds. If the light stays on or turns on during driving, it means that the 4WD system is not functioning properly and that service is required. 22. Coolant Temperature Warning Light

This light warns of an overheated engine condi- tion. If the light turns on while driving, safely pull over and stop the vehicle. If the air conditioner is on, turn it off. Also, shift the transmission into “N” (Neutral) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immedi- ately and call for service. (See page 384 for more infor- mation.)

198 INSTRUMENT PANEL AND CONTROLS

NOTE: As the coolant temperature gauge approaches 9H,9 this indicator will illuminate and a single chime will sound. Further overheating will cause the temperature gauge to pass 9H.9 In this case, the indicator will flash continuously and a continuous chime will sound, until the engine is allowed to cool.

CAUTION!

Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” and you hear continuous chimes, turn the engine off immediately, and call for service.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.

23. Coolant Temperature Gauge The temperature gauge indicates engine coolant tem- perature. Any reading within the normal range indicates that the cooling system is operating satisfactorily. The gauge pointer will likely indicate a high temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer. If the pointer rises to the “H” mark, safely pull over and stop the vehicle. If

the air conditioner is on, turn it off. Also, shift the transmission into “N” (Neutral) and idle the vehicle. If the needle remains on the “H” mark, turn the engine off immediately and call for service. (See page 384 for more information.) NOTE: The gauge pointer will remain near its last reading when the engine is turned off. It will return to a true reading when the engine is restarted.

CAUTION!

Do not leave your vehicle unattended with the en- gine running, as you would not be able to react to the temperature indicator if the engine overheats.

INSTRUMENT PANEL AND CONTROLS 199

24. Transmission Temperature Warning Light — If Equipped

This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into “N” (Neutral) and run the engine at idle or faster until the light turns off. 25. Trip Odometer Button

Changing the Display Press and release this button once to change the display from odometer to “Trip A.” Press and release it again to change the display from “Trip A” to “Trip B.” On vehicles equipped with a Base Cluster, press and release it once again to display the outside temperature. On vehicles equipped with a Mid Line Cluster, press and release it

200 INSTRUMENT PANEL AND CONTROLS

once again to display the outside temperature and com- pass heading in the screen below the speedometer. Refer to “Vacuum Fluorescent Display” for details Resetting the Trip Odometer Display the trip mileage that you want to reset, “Trip A” or “Trip B.” Then push and hold the button (approxi- mately 2 seconds) until the display resets to 0. The odometer must be in Trip Mode to reset the trip odom- eter. 26. 4WD Indicator Light — Vehicles Equipped with Selec-Tract II

This light alerts the driver that the vehicle is in the full-time four-wheel drive auto mode. In this mode, the system operates with a normal torque split of 42% front axle and 58% rear axle. It can redirect up to 100% of torque to the front or rear axle, if necessary.(See page 292 for more information.)

27. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Trip Odometer Button” for additional information. NOTE: U.S. federal regulations require upon transfer of vehicle ownership, the seller certify the mileage the vehicle has been driven. Therefore, if the odometer reading is changed because of repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. Vehicle Warning Messages When the appropriate conditions exist, messages such as “door” (for door ajar), “gATE” (for liftgate ajar), “gLASS” (for flip-up glass ajar), “gASCAP” (for fuel cap fault), or “CHANgE OIL” will display in the odometer.

If the instrument cluster is equipped with the NOTE: optional Electronic Vehicle Information Center (EVIC), then most warnings will display in the EVIC. (See page 206 for more information.) Fuel Cap Fault Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, the words “gASCAP” will display in the odometer. If this occurs, tighten the fuel filler cap properly and press the odometer reset button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). (See page 399 for more information.)

INSTRUMENT PANEL AND CONTROLS 201

Change Oil Message (Base & Mid Line Clusters Only) Your vehicle is equipped with an engine oil change indicator system. The “CHANgE OIL” message will flash in the instrument cluster odometer for approximately 12
seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following proce- dure:

1. Turn the ignition switch to the ON position (Do not start the engine).

202 INSTRUMENT PANEL AND CONTROLS

2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the LOCK position.

If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. 28. Cruise Indicator Light — If Equipped

This indicator lights when the electronic speed control system is turned on. (See page 147 for more information.)

29. Transmission Range Indicator This display indicator shows automatic transmission gear selection. (See page 281 for more information.) 30. Seat Belt Reminder Light

This light will turn on for several seconds after the ignition is turned ON as a reminder to “buckle

up.” This light will remain on as long as the seat belt remains unbuckled. (See page 48 for more information.) 31. Brake System Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the light turns on, it may indi- cate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system (if equipped). The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.

NOTE: The light may flash momentarily during sharp cornering maneuvers, which can change fluid level con- ditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD).

INSTRUMENT PANEL AND CONTROLS 203

In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the LOCK or ACC position to the ON position. The light should turn on for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not turn on, have the light inspected by an authorized dealer. (See page 310 for more information.) The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.

204 INSTRUMENT PANEL AND CONTROLS

32. Vehicle Security Alarm Indicator Light — If Equipped