2013 Jeep Grand Cherokee Owners Manual

Download PDF Manual
“Adaptive Cruise Control Off.” Adaptive Cruise Control Ready – When ACC is activated but the vehicle speed setting has not been selected, the display will read “Adaptive Cruise Control Ready.” ACC SET – When ACC is set, the set speed will display. – The set speed will continue to display in place of the odometer reading when changing the EVIC display while ACC is set. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Example Only The ACC screen will display once again if any ACC activity occurs, which may include any of the following: • Set Speed Change • Distance Setting Change • System Cancel 232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Driver Override • System Off • ACC Proximity Warning • ACC Unavailable Warning • The EVIC will return to the last display selected after five seconds of no ACC display activity. The “Clean Radar Sensor In Front Of Vehicle” message can sometimes be displayed while driving in highly reflective areas (i.e. tunnels with reflective tiles, or ice and snow). The ACC system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path this warning may temporarily occur. Display Warnings And Maintenance “Clean Radar Sensor In Front Of Vehicle” Warning The ACC “Clean Radar Sensor In Front Of Vehicle” warning will display when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such as in snow or heavy rain. The ACC system may also become temporarily blinded due to obstructions, such as mud, dirt or ice. In these cases, the EVIC will display “Clean Radar Sensor In Front Of Vehicle” and the system will deactivate. Clean Radar Sensor Warning NOTE: If the ACC “Clean Radar Sensor In Front Of Vehicle” warning is active Normal (Fixed Speed) Cruise Control is still available. For additional information refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located in the center of the vehicle behind the lower grille. To keep the ACC System operating properly, it is impor- tant to note the following maintenance items: • Always keep the sensor clean. Carefully wipe the sensor lens with a soft cloth. Be cautious not to damage the sensor lens. • Do not remove any screws from the sensor. Doing so could cause an ACC system malfunction or failure and require a sensor realignment. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 authorized dealer for service. • If the sensor is damaged due to a collision, see your • Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an ACC system failure or malfunction. When the condition that deactivated the system is no longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by simply reactivating it. NOTE: • If the “Clean Radar Sensor In Front Of Vehicle” message occurs frequently (e.g. more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at your authorized dealer. 234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Installing a snow plow, front-end protector, an after- market grille or modifying the grille is not recom- mended. Doing so may block the sensor and inhibit ACC operation. Removing ACC Sensor For Off-Roading NOTE: When off-roading, it may be advisable to remove the ACC sensor. The sensor is located behind the front lower grille in the center of the vehicle. After removing the lower fascia, you may remove the lower sensor and bracket assembly. To remove the sensor follow these instructions: 1. Unplug the connector by depressing the two tabs on the connector and pulling it out. Do not pull by the wiring or use any tools to remove the connector. 2. Remove the wiring christmas tree attachment from the back of the bracket. 3. Remove the two M6 fasteners that connect the bracket to the bumper. NOTE: Do not change the adjustment fasteners or pull the sensor off of the bracket. Doing so may misalign the sensor. Store the sensor and bracket assembly in a safe location. The wiring and connector must be stowed properly after the sensor and bracket assembly is removed. A connector plug is stowed on top of the bumper beam. Insert the wiring connector into the connector plug. NOTE: When the sensor is removed, Adaptive Cruise Control, Normal Cruise Control, and Forward Collision Warning will not be available. The cluster will display the warning “ACC/FCW Unavailable - Service Radar Sensor.” To reinstall the sensor and bracket assembly reverse the process above. The fastener torque required to assembly the bracket back to the beam is 6.6 ft lbs (9 N·m). ACC Unavailable Warning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable, Vehicle System Error”, there may be a temporary malfunction that limits ACC functionality. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable. If this occurs, try activating ACC again later, following a key cycle. If the problem persists, see your authorized dealer. Service ACC Warning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable Service Radar Sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. 236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Precautions While Driving With ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Adding A Trailer Hitch The weight of a trailer/hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a trailer/hitch, or if the ACC performance does not return to normal after removing the trailer/hitch see your authorized dealer. Offset Driving ACC may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. Turns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for convenience reasons, with no target vehicle detected. Once the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Using ACC On Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC perfor- mance may be limited. Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the ACC system to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient 238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE distance to the lane-changing vehicle. Always be atten- tive and ready to apply the brakes if necessary. Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. Stationary Objects And Vehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 Normal (Fixed Speed) Cruise Control Mode In addition to Adaptive Cruise Control mode, a normal (fixed speed) Cruise Control mode is available for cruis- ing at fixed speeds. The normal Cruise Control mode is designed to maintain a set cruising speed without requir- ing the driver to operate the accelerator. Cruise Control can only be operated if the vehicle speed is above 20 mph (32 km/h). To change between the different cruise modes, press the MODE button when the system is in either the OFF, READY or SET state. Pressing of the MODE button in any state will result in changing to the new Mode in the OFF state. General Information FCC Requirements For Vehicular Radar Systems Classification Specifications: 47 C.F.R. Part 15 47 C.F.R Part 15.515 240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In the normal Cruise Control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is detected. Be sure to maintain a safe distance between your vehicle and the vehicle ahead. Always be aware which mode is selected. To Set A Desired Speed When the vehicle reaches the speed desired, press the SET - button and release. The EVIC will display the set speed. NOTE: You must observe the display when setting or changing speed, not the speedometer. desired speed and press the SET - button. To Vary The Speed Setting There are two ways to change the set speed: • Use the accelerator pedal to adjust the vehicle to the • Tap the RES + or SET - button to increase or decrease the set speed in 1 mph (1.6 km/h) increments respec- tively. Hold the RES + or SET - button for 5 mph (8 km/h) increments. To Cancel The system will disable normal Cruise Control without erasing the memory if: • You softly tap or depress the brake pedal. • You press the CANCEL button. • The Electronic Stability Control/Traction Control Sys- tem (ESC/TCS) activates. To Resume Press the RES + button and then remove your foot from the accelerator pedal. The EVIC will display the last set speed. To Turn Off The system will turn off and erase the set speed in memory if: • You push the ON/OFF button. • You turn off the ignition. • You engage Four-Wheel Drive Low. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 If the Cruise Control system is turned off and reactivated, the system will return to the last driver setting (ACC or Normal Cruise Control). Forward Collision Warning — If Equipped The Forward Collision Warning (FCW) system provides the driver with audible and visual warnings (within the EVIC) when it detects a potential frontal collision. The warnings are intended to provide the driver with enough time to react and avoid the potential collision. 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FCW monitors the information from the forward looking sensor as well as the Electronic Brake Controller (EBC), wheel speed sensors, i.e., to calculate a probable rear-end collision. When the system determines that a rear-end collision is probable a warning message (both audible and visual) will be displayed on the EVIC. When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. FCW Message NOTE: • The minimum speed for FCW activation is 10 mph • When entering or driving in a curve, the FCW alerts may be triggered on objects other than vehicles such as (16 km/h). guard rails or sign posts based on the course predic- tion. This is expected and is a part of normal FCW activation and functionality. WARNING! Forward Collision Warning (FCW) is not intended to avoid a collision on its own, nor can FCW detect every type of collision. The driver has the responsi- bility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warn- ing could lead to serious injury or death. Changing FCW Status The FCW feature can be set to far, set to near or turned off in the Electronic Vehicle Information Center (EVIC) refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further in- formation. The FCW Status Off, Near or Far will be displayed in the EVIC. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 FCW settings can only be changed when the vehicle is in PARK. The default status of FCW is the “Far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. Example Only 244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Changing the FCW status to the “Near” setting, allows the system to warn you of a possible collision with the vehicle in front of you when you are much closer. This setting provides less reaction time than the “Far” setting, which allows for a more dynamic driving experience. Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. Example Only Example Only NOTE: In the “Off” setting FCW OFF will be displayed in the EVIC. 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 car, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rate of speed. • FCW will be disabled like ACC below with the un- available screens. FCW Unavailable Warning If the system turns off, and the EVIC displays “ACC/FCW Unavailable, Vehicle System Error”, there may be a tempo- rary malfunction that limits FCW functionality. Although the vehicle is still drivable under normal conditions, FCW will be temporarily unavailable. If this occurs, try activat- ing FCW again later, following a key cycle. If the problem persists, see your authorized dealer. Service FCW Warning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable Service Radar Sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. FCW Off Example NOTE: • The system will retain the last setting selected by the • FCW will not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the driver after ignition shut down. 246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE® REAR PARK ASSIST — IF EQUIPPED The ParkSense® Rear Park Assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.g. during a parking maneuver. Refer to ParkSense® System Usage Precautions for limitations of this system and recommendations. ParkSense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the ON/RUN position. ParkSense® can be active only when the shift lever is in REVERSE. If ParkSense® is enabled at this shift lever position, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above. The system will become active again if the vehicle speed is decreased to speeds less than approximately 6 mph (9 km/h). ParkSense® Sensors The four ParkSense® sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 18 in (45 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orienta- tion of the obstacle. ParkSense® Warning Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer- Pro- grammable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- strument Panel” for further information. The ParkSense® Warning Display is located in the Instru- ment cluster’s EVIC display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 ParkSense® Warning Display 248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. Park Assist System ON Park Assist System OFF The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 Slow Tone Fast Tone 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Rear Distance (in/cm) Greater than 79 in (200 cm) Audible Alert Chime Arcs Radio Mute None None No WARNING ALERTS 79-39 in (200-100 cm) Single 1/2 Second Tone 3 Solid (Continuous) Yes 39-25 in (100-65 cm) Slow 3 Slow Flashing Yes 25-12 in (65-30 cm) Fast 2 Slow Flashing Yes Less than 12 in (30 cm) Continuous 1 Slow Flashing Yes NOTE: ParkSense® will MUTE the radio, if on, when the system is sounding an audio tone. Enabling And Disabling ParkSense® ParkSense® can be enabled and disabled with the ParkSense® switch. approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARKSENSE OFF” message for as long as the vehicle is in REVERSE. When the ParkSense switch is pressed to dis- able the system, the instrument cluster will display the “PARKSENSE OFF” message for 252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The ParkSense® system will automatically dis- able when the system detects that a trailer with trailer brakes has been connected to the Integrated Trailer Brake Module. The EVIC will display “PARKSENSE OFF” message for as long as the vehicle is in reverse. The ParkSense® switch LED will be ON when ParkSense® is disabled or defective. The ParkSense® switch LED will be OFF when the system is enabled. Service The ParkSense® Rear Park Assist System When the ParkSense® Rear Park Assist System is mal- functioning, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “CLEAN PARK ASSIST SENSORS” or the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system has detected a faulted condition, the EVIC will display the “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE. Under this condition, ParkSense will not operate. If “CLEAN PARK ASSIST SENSORS” appears in the Electronic Vehicle Information Center (EVIC) make sure the outer surface and the underside of the rear fascia/ bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear, see an authorized dealer. If “SERVICE PARK ASSIST SYSTEM” appears in the EVIC, see an authorized dealer. Cleaning The ParkSense® System Clean the ParkSense® sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. ParkSense® System Usage Precautions affect the performance of ParkSense®. NOTE: • Ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the ParkSense® system oper- ating properly. • Jackhammers, large trucks, and other vibrations could • When you turn ParkSense® off, the instrument cluster will display “PARK ASSIST SYSTEM OFF.” Further- more, once you turn ParkSense® off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense® is turned off, the EVIC will display “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE. sounding a tone. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 • ParkSense®, when on, will MUTE the radio when it is • Clean the ParkSense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The ParkSense® system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/bumper. • Objects such as bicycle carriers, trailer hitches, etc., must not be placed within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the EVIC . 254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • On vehicles equipped with a tailgate, ParkSense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. CAUTION! • ParkSense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. WARNING! • Drivers must be careful when backing up even when using ParkSense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death. • Before using ParkSense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the loudspeaker the sensors sounds the continuous tone. Also, (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again. When displayed, static grid lines will illustrate the width of the vehicle while a dashed center-line will indicate the center of the vehicle to assist with aligning to a hitch/ receiver. The static grid lines will show separate zones that will help indicate the distance to the rear of the vehicle. The following table shows the approximate distances for each zone: WARNING! (Continued) could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen along with a caution note to “check entire sur- roundings” across the top of the screen. After five sec- onds this note will disappear. The ParkView® camera is located on the rear of the vehicle above the rear License plate. 256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Zone Red Yellow Green WARNING! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death. Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) 1 ft - 3 ft (30 cm - 1 m) 3 ft or greater (1 m or greater) CAUTION! • To avoid vehicle damage, ParkView® should only be used as a parking aid. The ParkView® camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/her shoulder when using ParkView®. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 Turning ParkView® On Or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft-key. NOTE: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Turning ParkView® On Or Off — With Navigation/Multimedia Radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Press the “camera setup” soft-key. 4. Enable or disable the rear camera feature by selecting the “enable rear camera in reverse” soft-key. 5. Press the “save” soft-key. 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink®), power liftgate and power sunroof switches may also be included, if equipped. Front Map/Reading Lights Lights are mounted in the overhead console. Each light can be turned on by pressing the switch on either side of the console. These buttons are backlit for night time visibility. Overhead Console Front Map/Reading Lights To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the UNLOCK button on the RKE is pressed. Courtesy Lights The courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press the lens a second time. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Courtesy Lights 260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglasses Bin Door At the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close. GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery. The HomeLink® buttons, located on either the overhead console, headliner or sunvisor, designate the three differ- ent HomeLink® channels. The HomeLink® indicator is located above the center button. Sunglasses Bin Door UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 HomeLink® Buttons/Overhead Consoles HomeLink® Buttons/Sunvisor/Headliner NOTE: HomeLink® is disabled when the Vehicle Secu- rity Alarm is active. 262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink® Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button. 4. Continue to hold both buttons and observe the indi- cator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Re- lease both buttons after the indicator light changes from slow to rapid. 5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Firmly press and release the “LEARN” or “TRAIN- ING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 6. Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the garage door opener/device activates, programming is complete. NOTE: If the garage door opener/device does not acti- vate, press the button a third time (for two seconds) to complete the training. To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Rolling Code” Step 2 and follow all remaining steps. Programming A Non-Rolling Code For programming Garage Door Openers manufactured before 1995. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Program- ming A Non-Rolling Code” Step 2 and follow all remaining steps. 3. Simultaneously press and hold both the HomeLink® button you want to program and the hand-held trans- mitter button. 4. Continue to hold both buttons and observe the indi- cator light. HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Re- lease both buttons after the indicator light changes from slow to rapid. 5. Press and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink® button is pressed. • To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 3. Continue to press and hold the HomeLink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds until HomeLink® has successfully accepted the frequency signal. The indi- cator light will flash slowly and then rapidly when fully trained. 4. Watch for the HomeLink® indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Press and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the HomeLink® button is pressed. • To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming A Single HomeLink® Button To reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button proceed with “Canadian/ Gate Operator Programming” Step 2 and follow all remaining steps. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 and release Using HomeLink® To operate, press the programmed HomeLink® button. Activation will now occur for the programmed device (i.e., garage door opener, gate opera- tor, security system, entry door lock, home/office light- ing, etc.,). The hand-held transmitter of the device may also be used at any time. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink® Universal Transceiver is disabled when the Vehicle Security Alarm is active. 268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips If you are having trouble programming HomeLink®, here are some of the most common solutions: • Replace the battery in the original hand-held transmitter. • Press the LEARN button on the Garage Door Opener • Did you unplug the device for programming and to complete the training for a Rolling Code. remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. WARNING! • Your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause unde- sired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- ber only signifies that Industry Canada technical speci- fications were met. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch 270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or On/Run position, for vehicles equipped with Keyless Enter-N-Go™). Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passen- gers are also properly secured. • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Express Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Sunroof — Express Press the switch forward and release it within one- half second and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Venting Sunroof — Express Press and release the Vent button within one half second and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. 272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition OFF Operation The power sunroof switches remain active for up to approximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. The time is programmable. Refer to “Elec- tronic Vehicle Information Center (EVIC)/Personal Set- tings (Customer-Programmable Features)” in “Under- standing Your Instrument Panel” for further information. COMMANDVIEW® SUNROOF WITH POWER SHADE — IF EQUIPPED The CommandView® sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 WARNING! • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or On/Run position, for vehicles equipped with Keyless Enter-N-Go™). Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passen- gers are also properly secured. • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. CommandView® Sunroof and Power Shade Switches 274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release it within one-half second. The sunroof and sunshade will open automatically from any position. The sunroof and sunshade will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Sunroof — Express Press the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close opera- tion, any movement of the switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Opening Power Shade — Express Press the shade switch rearward and release it within one-half second and the shade will open automatically from any position. The shade will open and stop auto- matically at the half-open position. Press the shade switch rearward again and release it within one-half sec- ond and the shade will open automatically to the full- open position. This is called “Express Open”. During Express Open operation, any movement of the shade switch will stop the shade. Opening Power Shade — Manual Mode To open the shade, press and hold the switch rearward . The shade will open and stop automatically at the half-open position. Press and hold the shade switch rearward again and the shade will open automatically to the full-open position. Any release of the switch will stop the movement and the shade will remain in a partially opened condition until the switch is pushed and held rearward again. Closing Power Shade — Express Press the switch forward and release it within one-half second and the shade will close automatically from any position. The shade will close fully and stop automati- cally. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the shade. NOTE: If the sunroof is open, it will automatically close during the ⬙Sun Shade Express Close⬙ movement. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 Closing Power Shade — Manual Mode To close the shade, press and hold the switch in the forward position. Any release of the switch will stop the movement and the shade will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. 276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition OFF Operation The power sunroof switches can be programmed to remain active for up to approximately ten minutes after the ignition switch has been turned OFF. Refer to “Elec- tronic Vehicle Information Center (EVIC)/Customer- Programmable Features (System Setup)” in “Under- standing Your Instrument Panel” for further information. NOTE: Opening either front door will cancel this fea- ture. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered. Power outlets labeled with a “key” are powered when the ignition switch is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 NOTE: • All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • To ensure proper operation a MOPAR® knob and element must be used. CAUTION! Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty. 278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. Center Console Outlet The rear power outlet is located in the right rear cargo area. Front Power Outlet In addition to the front power outlet, there is also a power outlet located in the storage area of the center console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 Rear Power Outlet Power Outlet Right Rear Quarter Panel Fuse NOTE: The rear power outlet can be switched to “bat- tery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel. 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet Fuse Locations 1 — M7 Fuse 20 A Yellow Power Outlet Right Rear Quarter Panel 2 — M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel 3 — M36 Fuse 20 A Yellow Power Outlet Console Bin WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge suffi- ciently to degrade battery life and/or prevent the engine from starting. (Continued) CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery. POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Play- station3 and XBox360 will exceed this power limit, as will most power tools. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 Power Inverter The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter 282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the Climate Con- trols. To turn on the power outlet, press the switch once. Press the switch a sec- ond time to turn the power outlet off. NOTE: When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUPHOLDERS There are two cupholders for the front seat passengers located in the center console. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Front Cupholders Rear Cupholders There are two cupholders for the rear seat passengers located in the fold-down center armrest. 284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glove Compartment The glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove box door. Glove Compartment Opened Glove Compartment Door Storage Large storage areas are built into the door panels for easy access. Center Console The center console contains both an upper and a lower storage area. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 Door Panel Storage Storage Compartment 286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage Compartment Latches Lower Storage Compartment WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury. CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the left side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Press in on the flashlight to release it. Press And Release 288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Three-Press Switch Cargo Storage Bins There are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Rear Storage Bins Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 Tether Strap Lower Storage Bins 290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place. Rear Cargo Cover WARNING! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle. Rear Cargo Tie-Downs The rear cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 Rear Cargo Tie-Downs 292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: (Continued) WARNING! (Continued) • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as pos- sible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or accident. REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer controls are located on the mul- tifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rear Wiper/Washer Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. Rotating the center portion upward once more will activate the washer pump which will con- tinue to operate as long as the switch is held. Upon release of the switch, the wipers will resume the continu- ous rear wiper operation. When this rotary control is in the OFF position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held. Once the switch is released it will return to the OFF position and the wipers will cycle several times before returning to the parked position. NOTE: As a protective measure, the pump will stop if the switch is held for more than 20 seconds. Once the switch is released the pump will resume normal opera- tion. 294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position. If the flipper glass is open, the rear window wiper/ washer functionality is interrupted and the wiper stops at that “park” position. When the flipper glass is closed, the rear wiper will resume wiper/washer functionality after five seconds. Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: If not equipped with crossbars, your authorized dealer can order and install MOPAR® crossbars built specifically for this roof rack system. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the crossbars, loosen the attachments, located at the upper edge of each crossbar, approximately eight turns using the anti-theft wrench provided with the MOPAR® crossbars. Then, move the crossbar to the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 desired position, keeping the crossbars parallel to the rack frame. Once the crossbar is in the desired position, retighten the with the wrench to lock the crossbar into position. NOTE: • To help control wind noise when the crossbars are not in use, place the front and rear crossbars approxi- mately 24 in (61 cm) apart. Optimal noise reduction can then be achieved by adjusting the front crossbar forward or aft using increments of 1 in (2.5 cm). • If the rear crossbar (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception. For improved satellite radio reception, avoid placing the rear crossbar over the satellite radio antenna. • The grab handles on the back of the vehicle (if equipped) are not to be used as a towing feature. 296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. (Continued) CAUTION! (Continued) • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle. WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . ..301 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . ..302 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . ..303 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) ▫ Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . . . . . . . ..313 Displays . . . . . . . . . . . . . . . . . . . . . . . . . . ..315 ▫ EVIC White Telltale Lights . . . . . . . . . . . . . ..322 ▫ EVIC Amber Telltale Lights . . . . . . . . . . . . ..324 ▫ EVIC Red Telltale Lights . . . . . . . . . . . . . . ..325 ▫ Engine Oil Change Indicator System . . . . . . ..328 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . ..329 ▫ Cruise Control. . . . . . . . . . . . . . . . . . . . . . ..331 ▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . ..332 ▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . .332 ▫ Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 ▫ Vehicle Info (Customer Information Features) . .333 ▫ Tire PSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . .334 ▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . ..335 ▫ Turn Menu OFF. . . . . . . . . . . . . . . . . . . . . ..335 298 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Keyless Enter-N-Go™ Display — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .335 ▫ Compass / Temperature Display . . . . . . . . ..336 ▫ Customer-Programmable Features (System Setup) . . . . . . . . . . . . . . . . . . . . . ..338 䡵 Uconnect® 730N/430/430N CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . ..347 ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . ..347 ▫ Operating Instructions (Uconnect® Phone) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .347 䡵 Uconnect® 130 . . . . . . . . . . . . . . . . . . . . . . . . .347 ▫ Operating Instructions — Radio Mode. . . . . ..348 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play . . . . . . . . . . . . . . ..351 ▫ Notes on Playing MP3 Files . . . . . . . . . . . . ..353 ▫ Operation Instructions - Auxiliary Mode . . . ..356 䡵 Uconnect® 130 WITH SATELLITE RADIO . . . ..356 ▫ Operating Instructions — Radio Mode. . . . . ..356 ▫ Operation Instructions — CD MODE for CD and MP3 Audio Play . . . . . . . . . . . . . . ..362 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . ..364 ▫ LIST Button (CD Mode for MP3 Play) . . . . . ..367 ▫ INFO Button (CD Mode for MP3 Play) . . . . ..367 ▫ Operating Instructions (Uconnect® Phone) — If Equipped . . . . . . . . . . . . . . . . ..368 ▫ Uconnect® Multimedia (Satellite Radio) — If Equipped . . . . . . . . . . . . . . . . ..368 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ Connecting The iPod® Or External USB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ Using This Feature. . . . . . . . . . . . . . . . . . . ..374 ▫ Controlling The iPod® Or External USB Device Using Radio Buttons . . . . . . . . . . . . . . . . . ..375 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . ..375 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . ..376 ▫ Bluetooth Streaming Audio (BTSA) . . . . . . . ..378 䡵 UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES)™ — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . . .380 ▫ Getting Started . . . . . . . . . . . . . . . . . . . . . ..380 ▫ Single Video Screen . . . . . . . . . . . . . . . . . . ..380 UNDERSTANDING YOUR INSTRUMENT PANEL 299 ▫ Play Video Games . . . . . . . . . . . . . . . . . . . ..384 ▫ Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 . . . . . . . . . . ..386 ▫ Important Notes For Single Video Screen System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ Play A DVD Using The Touch-Screen Radio . . .389 ▫ VES Remote Control – If Equipped . . . . . . . ..391 ▫ Remote Control Storage . . . . . . . . . . . . . . . ..393 ▫ Locking The Remote Control . . . . . . . . . . . ..394 ▫ Replacing The Remote Control Batteries. . . . ..394 ▫ Headphones Operation . . . . . . . . . . . . . . . ..395 ▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . ..396 ▫ Replacing The Headphone Batteries. . . . . . . ..397 300 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Unwired® Stereo Headphone Lifetime Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . .397 ▫ System Information . . . . . . . . . . . . . . . . . . ..398 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .415 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .416 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .416 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . ..417 䡵 RADIO OPERATION AND MOBILE PHONES . .417 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . ..418 ▫ Dual-Zone Manual Heating And Air Conditioning . . . . . . . . . . . . . . . . . . . ..418 ▫ Dual-Zone Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . ..422 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . ..429 INSTRUMENT PANEL FEATURES UNDERSTANDING YOUR INSTRUMENT PANEL 301 1 — Air Outlet 2 — Instrument Cluster 3 — Radio 4 — Glove Compartment 5 — Climate Controls 6 — Lower Switch Bank 7 — Hazard Switch 8 — Storage Bin 9 — ESC Button 10 — Ignition Switch 11 — Hood Release 12 — Fuel Door Release 13 — Headlight Switch 14 — Dimmer Control 302 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer Indicates the engine speed in revolutions per minute (RPM x 1000). 2. Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the ON/RUN position. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an autho- rized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. UNDERSTANDING YOUR INSTRUMENT PANEL 303 3. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD II that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. 304 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 4. Electronic Stability Control Malfunction Indicator Light — If Equipped (ESC) Activation/ The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected . NOTE: The “ESC Off Indicator Light” and the “ESC Activation/ Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to ON/RUN. Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation. 5. TOW/HAUL Indicator Light — If Equipped This light will illuminate when the TOW/ HAUL button has been selected. The TOW/ HAUL button is located in the center of the instrument panel (below the climate controls). 6. Turn Signal Indicator The arrows will flash with the exterior turn sig- nals when the turn signal lever is operated. A tone will chime, and an EVIC message will appear if either turn signal is left on for more than 1 mile (1.6 km). UNDERSTANDING YOUR INSTRUMENT PANEL 305 NOTE: If either indicator flashes at a rapid rate, check for a defective outside light bulb. 7. High Beam Indicator Indicates that headlights are on high beam. 8. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on. 9. Hill Descent Control Indicator Light — If Equipped The symbol indicates the status of the Hill Decent Control (HDC) feature. The lamp will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the “4WD Low” position and the vehicle speed is less then 30 mph (48 km/h). If these conditions are not met while attempt- ing to use the HDC feature, the HDC indicator lamp will flash on/off. 306 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Electronic Vehicle Information Center (EVIC) Display/Odometer Display The odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. Refer to “Electronic Vehicle Information Center”. 11. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. UNDERSTANDING YOUR INSTRUMENT PANEL 307 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. 308 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result. 12. Park/Headlight ON Indicator — If Equipped This indicator will illuminate when the park lights or headlights are turned on. 13. Seat Belt Reminder Light When the ignition switch is first turned to the ON/RUN position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Indicator Light will flash or remain on continuously. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 14. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. UNDERSTANDING YOUR INSTRUMENT PANEL 309 NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required . 310 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. 16. 4 LOW This light alerts the driver that the vehicle is in the four-wheel drive LOW mode. The front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped” in “Starting And Operating”. 17. Speedometer Indicates vehicle speed. 18. Fuel Door Reminder The fuel pump symbol points to the side of the vehicle where the fuel door is located. 19. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. UNDERSTANDING YOUR INSTRUMENT PANEL 311 20. Electronic Vehicle Information Center (EVIC) White Telltale Area This area will display the EVIC reconfigurable white telltales. For further information, refer to “Electronic vehicle Information Center (EVIC)”. 21. Electronic Vehicle Information Center (EVIC) Amber Telltale Area This area will display the EVIC reconfigurable amber caution telltales. For further information, refer to “Elec- tronic vehicle Information Center (EVIC)”. 22. Electronic Vehicle Information Center (EVIC) Red Telltale Area This area will display the EVIC reconfigurable red tell- tales. For further information, refer to “Electronic vehicle Information Center (EVIC)” 312 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Con- trol (ESC) is off. 24. Vehicle Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on. 25. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealer for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster. UNDERSTANDING YOUR INSTRUMENT PANEL 313 Electronic Vehicle Information Center (EVIC) Display Electronic Vehicle Information Center (EVIC) Display The EVIC consists of the following: • Fuel Economy • ACC: (If Equipped) • Vehicle Speed The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: 314 UNDERSTANDING YOUR INSTRUMENT PANEL • Trip Info • Terrain: (If Equipped) • Tire PSI: (If Equipped) • Vehicle Info • Messages • UNITS: SETTING • System Setup • Turn Menu Off EVIC Steering Wheel Buttons UNDERSTANDING YOUR INSTRUMENT PANEL 315 UP Button BACK Button Press and release the UP button to scroll up- ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units,

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Jeep Grand Cherokee Owners Manual