2006 Hyundai Tiburon Owners Manual

Download PDF Manual
2006 A010A02A-AAT WARRANTIES FOR YOUR HYUNDAI VEHICLE Please consult your Owner's Handbook & Warranty Information booklet for your vehicle's specific warranty coverage. A020A01A-AAT RESPONSIBILITY FOR MAINTENANCE The maintenance requirements for your new Hyundai are found in Section 5. As the owner, it is your responsibility to see that all maintenance operations specified by the manufacturer are carried out at the appropriate intervals. When the vehicle is used in severe driving conditions, more frequent maintenance is required for some operations. Maintenance requirements for severe operating conditions are also included in Section 5. OWNER'S MANUAL A030A05F-AAT Operation Maintenance Specifications All information in this Owner's Manual is current at the time of publication. However, Hyundai reserves the right to make changes at any time so that our policy of continual product improvement may be carried out. This manual applies to all Hyundai Tiburon models and includes descriptions and explanations of optional as well as standard equipment. As a result, you may find material in this manual that does not apply to your specific vehicle. HGK037 A070A01A-AAT CAUTION: MODIFICATIONS TO YOUR HYUNDAI Your Hyundai should not be modified in any way. Such modifications may adversely affect the performance, safety or durability of your Hyundai and may, in addition, violate conditions of the limited warranties covering the vehicle. Certain modifications may also be in violation of regulations established by the U.S. Department of Transportation and other federal or state agencies. A080A01S-AAT TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION Your vehicle is equipped with electronic fuel injection and other electronic components. It is possible for an improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic systems. For this reason, we recommend that you carefully follow the radio manufacturer's instructions or consult your Hyundai dealer for precautionary measures or special instructions if you choose to install one of these devices. A090A01A-AAT SAFETY AND VEHICLE DAMAGE WARNING This manual includes information titled as WARNING, CAUTION and NOTE. These titles indicate the following: WARNING: CAUTION: This indicates that a condition may result in harm, serious injury or death to you or other persons if the warning is not heeded. Follow the advice provided with the warning. This indicates that a condition may result in damage to your vehicle or its equipment if the caution is not heeded. Follow the advice provided with the caution. NOTE: This indicates that interesting or helpful information is being provided. A110A01A-AAT VEHICLE DATA COLLECTION AND EVENT DATA RECORDERS Your Hyundai vehicle is equipped with many high technology, electronically controlled systems that help to ensure your vehicle operates properly and provides the performance that you expect. These systems utilize computers to monitor the operation of various systems and components and help to control their operation. These computerized system operations are wide-ranging and involve components to reduce emissions, to continuously evaluate the readiness of the airbag and seat belt pretensioner systems, to determine when the airbag and seat belt pre-tensioner systems should be deployed and then to activate the deployment, and if equipped, to operate anti-lock braking, traction control and electrical stability control to assist the driver to control the vehicle in difficult driving situations. These systems electronically store information that is useful to service technicians when they need to diagnose and repair these systems. Additional information is stored only when a crash occurs that results in the deployment of the airbags or seat belt pre-tensioners. This type of data storage is done by devices called event data recorders(EDR). After a crash event, the airbag and seat belt pre-tensioner computer system, known as the Supplemental Restraint System Control Module (SRSCM) or Airbag Control Unit (ACU), may record some information about the condition of the vehicle and how it was being operated. This information consists of data related to seat belt usage and if there was diagnostic information in the airbag or seat belt systems at the time that a crash occurred, and if the ACU sensed that a crash of sufficient severity occurred to require seat belt pre-tensioner or airbag deployment. To retrieve this information, special equipment is needed and access to the vehicle or the device that stores the data is required. Hyundai will not access information about a crash event or share it with others except: o in response to an official request of police or similar government office, or o with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee, or o as part of Hyundai’s defense of litigation, or o as required by law. A040A01A-AAT FOREWORD Thank you for choosing Hyundai. We are pleased to welcome you to the growing number of discriminating people who drive Hyundais. The advanced engineering and high-quality construction of each Hyundai we build is something of which we're very proud. Your Owner's Manual will introduce you to the features and operation of your new Hyundai. It is suggested that you read it carefully because the information it contains can contribute greatly to the satisfaction you receive from your new car. The manufacturer also recommends that all service and maintenance on your car be performed by an authorized Hyundai dealer. Hyundai dealers are prepared to provide high-quality service, maintenance and any other assistance that may be required. A050A04A-AAT HYUNDAI MOTOR COMPANY Note : Because future owners will also need the information included in this manual, if you sell this Hyundai, please leave the manual in the vehicle for their use. Thank you. CAUTION: Severe engine and transaxle damage may result from the use of poor quality fuels and lubricants that do not meet Hyundai specifications. You must always use high quality fuels and lubricants that meet the specifica- tions listed on Page 9-4 in the Vehicle Specifications section of the Owner's Manual and which also appear in the Service Station Information on the back cover of the Owner's Manual. Copyright 2006 Hyundai Motor Company. All rights reserved. No part of this publication may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the prior written permission of Hyundai Motor Company. A100A03A-AAT GUIDE TO HYUNDAI GENUINE PARTS 1. What are Hyundai Genuine Parts? Hyundai Genuine Parts are the same parts used by Hyundai Motor Company to manu- facture vehicles. They are designed and tested for the optimum safety, performance, and reliability to our customers. 2. Why should you use genuine parts? Hyundai Genuine Parts are engineered and built to meet rigid manufacturing require- ments. Using imitation, counterfeit or used salvage parts is not covered under the Hyundai New Vehicle Limited Warranty or any other Hyundai warranty. In addition, any damage to or failure of Genuine Hyundai Parts caused by the installation or failure of an imitation, counterfeit or used salvage part is not covered by any Hyundai Warranty. To find the closest authorized dealer call 1-800-826-CARS 3. How can you tell if you are purchasing Hyundai Genuine Parts? Look for the Hyundai Genuine Parts Logo on the package (see below). Hyundai Genuine Parts exported to the United States are packaged with labels written only in English. Hyundai Genuine Parts are only sold through authorized Hyundai Dealerships. A100A03L A100A01L A100A02L A100A04L TABLE OF CONTENTS FEATURES OF YOUR HYUNDAI DRIVING YOUR HYUNDAI WHAT TO DO IN AN EMERGENCY CORROSION PREVENTION & APPEARANCE CARE VEHICLE MAINTENANCE REQUIREMENTS DO-IT-YOURSELF MAINTENANCE EMISSION CONTROL SYSTEMS CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS VEHICLE SPECIFICATIONS INDEX 10 SECTION INSTRUMENTS AND CONTROLS B250A02GK-AAT B250A01GK-A 1. Electronic Stability Program (ESP) Switch (If installed) 2. Panel Brightness Control Knob (Rheostat Switch) 3. Multi-Function Light Switch 4. Windshield Wiper/Washer Switch 5. Front Fog Light switch (If installed) 6. Hazard Warning Switch 7. Digital Clock 8. Passenger's Air Bag 9. Glove Box 10.Hood Release Lever 11.Fuse Box Relay 12.Steering Wheel Tilt Lever (If installed) 13.Horn and Driver's Airbag 14.Cruise Control Switch (If installed) 15.Heating and Cooling Controls 16.Ashtray 17.Cigarette Lighter 18.Shift Lever 19.Audio System (If installed) 20.Parking Brake Lever 21.Center Console CAUTION: When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor on the instrument panel surface. If there is any leakage from the air freshener onto these areas (Instrument cluster, instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these areas, wash them with water immediately. YOUR VEHICLE AT A GLANCE B255A02GK-AAT INDICATOR SYMBOLS ON THE INSTRUMENT PANEL Turn Signal Indicator Lights Tail Gate Open Warning Light ABS Service Reminder Indicator (SRI) (If installed) SRS (Airbag) Service Reminder Indicator (SRI) High Beam Indicator Light Malfunction Indicator Light Low Oil Pressure Warning Light Seat Belt Reminder Light and Chime Parking Brake/ Low Brake Fluid Level Warning Light CRUISE Indicator Light (If installed) Charging System Warning Light CRUISE SET Indicator Light (If installed) Door Ajar Warning Light and Chime Low Fuel Level Warning Light Electronic Stability Program (ESP) Indicator Lights (If installed) * More detailed explanations of these items will be found beginning on page 1-38. FEATURES OF YOUR HYUNDAI Fuel Recommendations ................................................ 1-2 Breaking in Your New Hyundai ..................................... 1-3 Keys .............................................................................. 1-3 Door (Teft-Alarm System) ...................................... 1-4, 1-6 Power Windows ............................................................ 1-9 Seats ........................................................................... 1-10 Seat Belts.................................................................... 1-16 Child Restraint System ............................................... 1-21 Supplemental Restraint (AIRBAG) System (SRS) ..... 1-28 Instrument Cluster and Indicator Lights ...................... 1-36 Warning and Indicator Lights ...................................... 1-38 Multi-Function Light Switch ......................................... 1-47 Windshield Wiper/Washer Switch ............................... 1-49 Sunroof ....................................................................... 1-55 Mirror ........................................................................... 1-58 Hood Release ............................................................. 1-61 Cruise Control ............................................................. 1-67 Audio Remote Control Switch ..................................... 1-70 Heating and Cooling Control ....................................... 1-71 Stereo Sound System ................................................. 1-88 Audio System .............................................................. 1-90 Antenna ..................................................................... 1-127 1FEATURES OF YOUR HYUNDAI FUEL RECOMMENDATIONS B010A02JM-AAT Use Unleaded Gasoline B010B01A-AAT What About Gasohol? B010D01A-AAT Do Not Use Methanol Fuels containing methanol (wood alcohol) should not be used in your Hyundai. This type of fuel can reduce vehicle performance and damage components of the fuel system. CAUTION: Your Hyundai's New Vehicle Limited War- ranty may not cover damage to the fuel system and any performance problems that are caused by the use of fuels containing methanol or fuels containing MTBE (Methyl Tertiary Butyl Ether) over 15.0% vol. (Oxy- gen Content 2.7% weight.) Gasohol (a mixture of 90% unleaded gasoline and 10% ethanol or grain alcohol) may be used in your Hyundai. However, if your engine devel- ops driveability problems, the use of 100% unleaded gasoline is recommended. Fuels with unspecified quantities of alcohol, or alcohols other than ethanol, should not be used. B010C01A-AAT Use of MTBE Hyundai recommends that fuels containing MTBE (Methyl Tertiary Butyl Ether) over 15.0% vol. (Oxygen Content 2.7% weight) should not be used in your Hyundai. Fuel containing MTBE over 15.0% vol. (Oxygen Content 2.7% weight) may reduce vehicle per- formance and produce vapor lock or hard starting. UNLEADED FUEL ONLY B010A02GK Unleaded gasoline with a Pump Octane Rating of 87 (Research Octane Number 91) or higher must be used in your Hyundai. WARNING: o Do not "top off" after the nozzle auto- matically shuts off when refueling. o Tighten the cap until it clicks, otherwise the " " light will illuminate. o Always check that the fuel cap is in- stalled securely to prevent fuel spillage in the event of an accident. BREAKING IN YOUR NEW HYUNDAI KEYS B010E01A-AAT Gasolines for Cleaner Air B020A01S-AAT During the First 1,200 Miles (2,000 Km) B030A01A-AAT To help contribute to cleaner air, Hyundai rec- ommends that you use gasolines treated with detergent additives, which help prevent deposit formation in the engine. These gasolines will help the engine run cleaner and enhance per- formance of the Emission Control System. No formal "break-in" procedure is required with your new Hyundai. However, you can contrib- ute to the economical operation and durability of your Hyundai by observing the following recom- mendations during the first 1,200 miles (2,000 km). FEATURES OF YOUR HYUNDAI B010F01A-AAT Operation in Foreign Countries If you are going to drive your Hyundai in another country, be sure to: o Observe all regulations regarding registra- tion and insurance. o Determine that acceptable fuel is available. o Don't drive faster than 55 MPH (88 km/h). o While driving, keep your engine speed (rpm, or revolutions per minute) between 2,000 rpm and 4,000 rpm. o Use moderate acceleration. Don't start quickly or depress the accelerator pedal fully. o For the first 200 miles (300 km), try to avoid hard stops. o Don't lug the engine (in other words, don't drive so slowly in too high a gear that the engine "bucks"-shift to a lower gear). o Whether going fast or slow, vary your speed o Don't let the engine idle longer than 3 minutes from time to time. at one time. o Don't tow a trailer during the first 1,200 miles (2,000 km) of operation. B030A01E For greater convenience, the same key oper- ates all the locks in your Hyundai. However, because the doors can be locked without a key, carrying a spare key is recommended in case you accidentally lock one key inside the car. 1FEATURES OF YOUR HYUNDAI B030B01S-AAT Record Your Key Number B030C01Y-AAT ILLUMINATED IGNITION SWITCH (If installed) B030B01E A code number is stamped on the key number plate that came with the keys to your Hyundai. This key number plate should be kept in a safe place, not in the vehicle. The key number should also be recorded in a place where it can be found in an emergency. If you need additional keys, or if you should lose your keys, your authorized Hyundai dealer can make new keys if you can supply the key number. B030C01E-1 Whenever a door is opened, the ignition switch will be illuminated for your convenience, pro- vided the ignition switch is not in the "ON" position. The light will go off approximately 10 seconds after closing the door or when the ignition switch is turned on. DOOR B040A02Y-AAT DOOR LOCKS WARNING: o Unlocked doors can be dangerous. Be- fore you drive away (especially if there are children in the car), be sure that all the doors are securely closed and locked so that the doors cannot be inadvertently opened from the inside. This helps en- sure that the doors will not be opened accidentally. Also, when combined with the proper use of seat belts, locking the doors helps keep occupants from being ejected from the car in case of an acci- dent. o Before opening the door, always look for and avoid oncoming traffic. o In case of accident, the door is unlocked automatically (If installed). B040B01JM-AAT Locking and unlocking front doors with a key UNLOCK LOCK HGK2008 o The door can be locked or unlocked with a key. o Lock the door by turning the key toward the front of the vehicle and unlock it by turning the key toward the rear. NOTE: The driver's door can be unlocked by turn- ing the key once toward the rear. If you wish to unlock all doors, turn the key again toward the rear within 4 seconds. The passenger's side will lock or unlock all doors with just one rotation. B040C01S-AAT Locking From the Outside B040D01S-AAT Locking From the Inside FEATURES OF YOUR HYUNDAI UNLOCK LOCK HGK2010 To lock the doors from the inside, simply close the door and push the lock switch to the "LOCK" position. When this is done, neither the outside nor the inside door handle can be used. NOTE: When the door is locked, the red mark on the switch is not visible. HGK2009 The doors can be locked without a key. To lock the doors first push the inside lock switch to the "LOCK" position so that the red mark on the switch is not visible, then close the door. NOTE: o When locking the door this way, be care- ful not to lock the door with the ignition key left in the vehicle. o To reduce the chance of theft, always remove the ignition key, close all win- dows, and lock all doors when leaving your vehicle unattended. 1FEATURES OF YOUR HYUNDAI B040G02GK-GAT Central Door Lock o If the door is locked/unlocked multiple times in rapid succession with either the vehicle key or door lock switch, the sys- tem may stop operating temporarily in order to protect the circuit and prevent damage to system components. HGK2009 The central door locking is operated by pushing the driver's door lock switch toward the front or rear of the vehicle. If the passenger door is open when the switch is pushed, the door will remain locked when closed. NOTE: o When pushing the switch toward the rear, all doors will unlock. When pushing the switch toward the front, all doors will lock. o When the door is unlocked, the red mark on the switch is visible. o The central door locking is operated by turning the key (driver's door only) to- ward the front or rear of the vehicle. THEFT-ALARM SYSTEM B070A01A-AAT (If Installed) This system is designed to provide protection from unauthorized entry into the car. This sys- tem is operated in three stages: the first is the "Armed" stage, the second is the "Alarm" stage, and the third is the "Disarmed" stage. If trig- gered, the system provides an audible alarm with blinking of the turn signal light. B070B02GK-AAT Armed Stage Park the car and stop the engine. Arm the system as described below. 1) Remove the ignition key from the ignition switch. 2) Make sure that the engine hood and tail gate are closed and latched. 3) Lock the doors using the transmitter of the keyless entry system. After completion of the steps above, the turn signal light will blink once to indicate that the system is armed. NOTE: 1) If any door, tail gate or engine hood remains open, the system will not be armed. 2) If this happens, rearm the system as described above. 3) Once the system is armed, only the tail gate may be unlocked using the key without disarming the system. CAUTION: Do not arm the system until all passengers have left the car. If the system is armed while a passenger(s) remains in the car, the alarm may be activated when the remaining passenger(s) leaves the car. FEATURES OF YOUR HYUNDAI B070C01GK-AAT Alarm Stage B070D04GK-AAT Disarmed Stage The alarm will be activated if any of the following occur while the car is parked and the system is armed. 1) A front door is unlocked and opened without using the transmitter. 2) The tail gate is opened without using the key. 3) The engine hood is opened. The siren will sound and the turn signal lamp will blink continuously for 30 seconds. (This hap- pens 3 times). To turn off the system, unlock the door with the transmitter. CAUTION: Avoid trying to start the engine while the system is armed. LOCK UNLOCK HGK102 The system will be disarmed when either of the following steps are taken: 1) The driver's or passenger's door is un- locked by depressing the "UNLOCK" button on the transmitter. 2) In the middle of alarming or after alarming, it keeps for 30 seconds when the key is turned to the "ON" position. After completing one of steps above, the turn signal light will blink twice to indicate that the system is disarmed. NOTE: If any door, tail gate or engine hood is not opened within 30 seconds, the system will be rearmed. 1FEATURES OF YOUR HYUNDAI B075E01O-AAT Panic Warning PANIC HGK102 1. Push the "PANIC" button on the transmitter. 2. At the same time, the siren will sound and the turn signal lights will blink for 30 seconds. 3. To turn off the system, push the "PANIC" button again on the transmitter. B070F02A-AAT KEYLESS ENTRY SYSTEM (If installed) NOTE: This device complies with Part 15 of the FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion. WARNING: Changes or modifications not expressly approved by the party responsible for com- pliance could void the user's authority to operate the equipment. NOTE: The transmitter will not work if any of fol- lowing occur: - The ignition key is in ignition switch. - You exceed the operating distance limit (10 m). - The battery in the transmitter is weak. - Other vehicles or objects may be block- ing the signal. - The weather is extremely cold. - The transmitter is close to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter. When the transmitter does not work cor- rectly, open and close the door with the ignition key. If you have a problem with the transmitter, contact an authorized Hyundai Dealer. NOTE: Keep the transmitter away from water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manu- facturer vehicle warranty. Locking doors 1. Close all doors. 2. Push the "LOCK" button on the transmitter. 3. At the same time all doors lock, the turn signal lights will blink once to indicate that the system is armed. Unlocking doors 1. Push the "UNLOCK" button on the transmitter. 2. At the same time all doors unlock, the turn signal lights will blink twice to indicate that the system is disarmed. B070E02GK-GAT Replacing the battery When the transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light. Replace the battery as soon as possible. Battery type : CR2016 Replacement instructions: Screwdriver HGK122 1. Carefully separate the case with a blade screwdriver as shown in the illustration. FEATURES OF YOUR HYUNDAI POWER WINDOW B050A01GK-AAT Battery HGK121 (1) 2. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same(+side facing up), then insert it in the transmitter. NOTE: Install a new battery within 30 seconds after removing the old one. If installing a new battery takes more than 30 seconds, take the following steps. 1) Turn the ignition key to the "ACC" posi- tion. 2) Make sure that the turn signal lamps blink once by pushing the "LOCK" or "UNLOCK" button on the transmitter. HGK2015 The power windows operate only when the ignition key is in the "ON" position. The main switches are located on the driver's arm rest and control the front windows on the respective sides of the vehicle. The windows may be opened by depressing the front portion of the switch. To stop at the desired opening, release the switch. The window may be closed by pulling the front portion of the switch. In order to prevent operation of the passenger front window by the passenger, a window lock switch (1) is provided on the arm rest of the driver's door. To disable the passenger's power window, push the win- dow lock switch. To revert to normal operation, push in on the window lock switch again. 1FEATURES OF YOUR HYUNDAI 10 SEATS Auto-Down Window (Driver's Side) (If Installed) B080A02A-AAT ADJUSTABLE FRONT SEATS WARNING: o Never adjust the driver’s seat while the vehicle is moving. Any sudden or unex- pected movement of the seat could cause you to lose control of the vehicle result- ing in an accident. Only adjust the driver’s seat when the vehicle is station- ary. o Do not sit or lean unnecessarily close to the airbag. Position the seat so that you can sit as far back as possible from the airbag and still comfortably reach all controls. B050A02GK The Auto-Down window is moved to its fully open position by pushing the switch. To stop at the desired position push in on the switch again. HGK2016 WARNING: (1)Be careful that someone's head, hands and body are not trapped by a closing window. (2)Never try to operate the main switch on the driver's door and the individual door window switch in opposing directions at the same time. If this is done, the window will stop and cannot be opened or closed. (3)Do not leave children alone in the car. Always remove the ignition key for their safety. FEATURES OF YOUR HYUNDAI 11 B080C02A-AAT Adjusting Seatback Angle B080B03A-AAT Adjusting Seat Forward and Rearward WARNING: After adjusting the seat, always check that it is securely locked into place by attempt- ing to move the seat forward or reverse without using the lock release lever. Sud- den or unexpected movement of the driver's seat could cause you to lose control of the vehicle resulting in an accident. HGK2027 To move the seat toward the front or rear, pull the lock release lever upward. This will release the seat on its track so you can move it forward or rearward to the desired position. When you find the position you want, release the lever and slide the seat forward or rearward on its track until it locks into the desired position and cannot be moved further. HGK2028 To recline the seatback, lean forward to take your weight off it, then pull up on the recliner control lever at the outside edge of the seat. Now lean back until the desired seatback angle is achieved. To lock the seatback into position, release the recliner control lever. 1FEATURES OF YOUR HYUNDAI 12 WARNING: Riding with a reclined seatback increases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work prop- erly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt or the occupant's neck will strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted, and with the seatbacks upright. B080D02JM-AAT Adjustable Headrests WARNING: Lock Knob HGK2032 Headrests are designed to help reduce the risk of neck injuries. To raise the headrest, pull it up. To lower the headrest, push it down while pressing the lock knob. To remove the headrest, raise it as far as it can go then press the lock knob while pulling upward. This should only be done when the seat is not occupied. B080D01JM o For maximum effectiveness in case of an accident the headrest should be ad- justed so the middle of the headrest is at the same height as the top of the occupant's eyes. For this reason, the use of a cushion that holds the body away from the seatback is not recom- mended. o Do not operate vehicle with the head- rests removed as injury to the occupants may occur in the event of an accident. Headrests may provide protection against neck injuries when properly adjusted. o Do not adjust the headrest hejght while the vehicle is in motion. B080E01F-AAT Lumbar Support Control (Driver's seat only) B080F01F-AAT Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed) B129A01F-AAT REAR SEAT POSITIONS FEATURES OF YOUR HYUNDAI 13 SOFT FIRM B129A01GK HGK2030 The driver's seat is equipped with adjustable lumbar support. To increase the amount of lumbar support, pull the lever forward. To decrease it, push the lever toward the rear. HGK2029 To raise or lower the front part of the seat cushion, turn the knob forward or rearward. WARNING: This vehicle contains two rear seating po- sitions only and a seat belt for each seating position. Thus, never permit more than two occupants to ride in the rear seat because an unrestrained occupant could be seri- ously injured or killed in the event of a vehicle crash. 1FEATURES OF YOUR HYUNDAI 14 B130A01GK-AAT REAR SEAT ENTRY (Walk in device) The driver and front passenger's seatbacks should be tilted to enter the rear seat. (1) (1) (2) HGK2036 By pulling up the walk in device lever (1) at the left-upper side of the driver side seatback, the seatback will tilt forward. Then pull the lock release lever (2) up to move the seat forward. HGK2036-1 By pulling up the walk in device lever (1) at the right-upper side of the passenger side seatback, the seatback will tilt forward. Then push the seat forward to allow the occupants to enter. Recliner Memory By pulling up the walk in device lever (1) the seatback is reclined and returned to the original position. WARNING: Don't drive with the passenger side seatback reclined. It is dangerous to move it while driving. Be sure the seatback is caterred firmly before driving. B099A01F-AAT BEFORE FOLDING THE REAR SEATS HGK2034 In order to prevent the shoulder belt from being damaged while folding the rear seat, the shoul- der belt must be passed through the hanger to keep it out of the way. CAUTION: Seat belts must be removed from the hanger when in use. B110A02S-AAT FOLDING REAR SEATBACKS WARNING: The purpose of the fold-down rear seatbacks is to allow you to carry longer objects than could otherwise be accommo- dated. Never allow passengers to sit on top of the folded down seat back while the car is moving as this is not a proper seating position and no seat belts are available for use. This could result in injury in case of an accident or sudden stop. Objects carried on the folded down seatback should not extend higher than the top of the front seats. This could allow cargo to slide for- ward and cause injury or damage during sudden stops. HGK2035 The rear seatbacks may be folded to facilitate carrying long items or to increase the luggage capacity of the vehicle. o To unlock the seatback, push the seatback locking button, then pull forward on the seatback panel. o When you return the seatback to its upright position, always be sure it has locked into position by pulling and pushing on the top of the seatback. FEATURES OF YOUR HYUNDAI 15 B140A01S-AAT REAR SEAT WARNING B140A01GK For the safety of all passengers, luggage or other cargo should not be piled higher than the top of the seatback. In addition, do not place objects on the rear shelf as they may move forward during braking or in an accident and strike vehicle passengers. 1FEATURES OF YOUR HYUNDAI 16 SEAT BELT B150A02S-AAT SEAT BELT PRECAUTIONS B150B04Y-AAT Infant or Small Child WARNING: All occupants of the vehicle must wear their seat belts at all times. Seat belts and child restraints reduce the risk of serious or fatal injuries for all occupants in the event of a collision or sudden stop. Without a seat belt, occupants could be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle. Properly worn seat belts greatly reduce these hazards. Even with advanced airbags, unbelted occupants can be severely in- jured by a deploying airbag. Always follow the precautions about seat belts, airbags and occupant safety contained in this manual. All 50 states have child restraint laws. You should be aware of the specific requirements in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. Information about the use of these restraints begins on page 1-21. WARNING: Every person in your vehicle needs to be properly restrained at all times, including infants and children. Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the interior. Always use a child restraint appropriate for your child's height and weight, see page 1-21. NOTE: Small children are best protected from in- jury in an accident when properly restrained in the rear seat by a child restraint system that meets the requirements of the Federal Motor Vehicle Safety Standards. Before buying any child restraint system, make sure that it has a label certifying that it meets Federal Motor Vehicle Safety Stan- dard 213. The restraint must be appropriate for your child's height and weight. Check the label on the child restraint for this information. See page 1-21. B150C02A-AAT Larger Children Children who are too large for child restraint systems should always occupy the rear seat and use the available lap/shoulder belts. The lap portion should be fastened snug on the hips and as low as possible. Check belt fit periodically. A child's squirming could put the belt out of posi- tion. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. If a larger child (over age 13) must be seated in the front seat, the child should be securely restrained by the available lap/shoulder belt and the seat should be placed in the rearmost position. Children under the age of 13 should be restrained securely in the rear seat. Never place a child under the age of 13 in the front seat. NEVER place a rear facing child seat in the front seat of a vehicle. B150D01A-AAT Pregnant Women B150G02A-AAT Do Not Lie Down The use of a seat belt is recommended for pregnant women to lessen the chance of injury in an accident. When a seat belt is used, the lap belt portion should be placed as low and snugly as possible on the hips, not across the abdo- men. For specific recommendations, consult a physician. To reduce the chance of injuries in the event of an accident and to achieve maximum effective- ness of the restraint system, all passengers should be sitting up and the front seats should be in an upright position when the car is moving. A seat belt cannot provide proper protec-tion if the person is lying down in the rear seat or if the front seat is in a reclined position. B150E01A-AAT Injured Person A seat belt should be used when an injured person is being transported. When this is nec- essary, you should consult a physician for recommendations. B150F01A-AAT One Person Per Belt Two people (including children) should never attempt to use a single seat belt. This could increase the severity of injuries in case of an accident. WARNING: Riding with a reclined seatback increases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work prop- erly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt causing serious internal injuries or the occupant's neck could strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted (see page 1-19), and with the seatbacks upright. FEATURES OF YOUR HYUNDAI 17 B160A02A-AAT CARE OF SEAT BELTS Seat belt systems should never be disassembled or modified. In addition, care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or other abuse. WARNING: When you return the rear seatback to its upright position after the rear seatback was folded down, be careful not to damage the seat belt webbing or buckle. Be sure that the webbing or buckle does not get caught or pinched in the rear seat. A seat belt with damaged webbing or buckle will not be as strong and could possibly fail during a collision or sudden stop, resulting in seri- ous injury. B160B01A-AAT Periodic Inspection It is recommended that all seat belts be in- spected periodically for wear or damage of any kind. Parts of the system that are damaged should be replaced as soon as possible. 1FEATURES OF YOUR HYUNDAI 18 B160C01A-AAT Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not be used because they may damage and weaken the fabric. B160D01A-AAT When to Replace Seat Belts Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an accident. This should be done even if no damage is visible. Additional ques- tions concerning seat belt operation should be directed to your Hyundai Dealer. B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the position. WARNING: o Verify the shoulder belt anchor is locked into position at the appropriate height. Never position the shoulder belt across your neck or face. Improperly posi- tioned seat belts can cause serious inju- ries in an accident. o Failure to replace seat belts after an accident could leave you with damaged seat belts that will not provide protec- tion in the event of another collision leading to personal injury or death. Replace your seat belts after being in an accident as soon as possible. HGK2038 You can adjust the height of the shoulder belt anchor to one of the 4 positions for maximum comfort and safety. If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder nearest the door and not your neck. To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appro- priate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing the height adjuster button. B180A01L-AAT SEAT BELT-Driver's 3-Point System with Emergency Locking Retractor: To Fasten Your Belt NOTE: Seat belt reminder light comes and stays on until the seat belt is fastened when the ignition key is turned "ON" or "START". And, the warning chime will also sound for about 6 seconds. B190A02Y-AAT SEAT BELTS -Front Passenger and Rear Seat 3-Point System with Combination Locking Retractor To Fasten Your Belt Combination retractor type seat belts are in- stalled in the rear seat positions to help accom- modate the installation of child restraint sys- tems. Hyundai strongly recommends that chil- dren always be seated in the rear seat. NEVER place any infant restraint system in the front seat of the vehicle. This type of seat belt combines the features of both an emergency locking retractor seat belt and an automatic locking retractor seat belt. To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle. B180A01L To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle. The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly. Check to make sure that the belt is properly locked and that the belt is not twisted. FEATURES OF YOUR HYUNDAI 19 When not securing a child restraint, the seat belt operates in the same way as the driver's seat belt (Emergency Locking Retractor Type). It automatically adjusts to the proper length only after the lap belt portion of the seat belt is adjusted manually so that it fits snugly around your hips. When the seat belt is fully extended from the retractor to allow the installation of a child restraint system, the seat belt operation changes to allow the belt to retract, but not to extend. (Automatic Locking Retractor Type) see page 1-25. NOTE: Although the combination retractor pro- vides the same level of protection for seated passengers in either emergency or auto- matic locking modes, it is recommended that seated passengers use the emergency locking feature for improved convenience. The automatic locking function is intended to facilitate child restraint installation. To convert from the automatic locking feature to the emergency locking operation mode, allow the unbuckled seat belt to fully re- tract. 1FEATURES OF YOUR HYUNDAI 20 WARNING: o For maximum restraint system protec- tion, seat belts must always be used whenever the car is moving. o Seat belts are most effective when seatbacks are in the upright position. o Children age 12 and younger must al- ways be properly restrained in the rear seat. Never allow children to ride in the front passenger seat. If a child over 13 must be seated in the front seat, he/she must be properly belted and the seat should be moved as far back as possible. o Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt can cause se- rious injuries in a crash. The shoulder belt should be positioned midway over your shoulder across your collarbone. o Avoid wearing twisted seat belts. A twisted belt can't do its job as well. In a collision, it could even cut into you. Be sure the belt webbing is straight and not twisted. o Be careful not to damage the belt web- bing or hardware. If the belt webbing or hardware is damaged, replace it. B200A01A-AAT Adjusting Your Seat Belt B210A01A-AAT To Release the Seat Belt B210A01L The seat belt is released by pressing the re- lease button in the locking buckle. When it is released, the belt should automatically draw back into the retractor. If this does not happen, check the belt to be sure it is not twisted, then try again. B200A01L WARNING: You should place the lap belt portion as low as possible and snugly across your hips, not on your waist. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration. Never wear the seat belt under the arm nearest the door. CHILD RESTRAINT SYSTEM B230A04A-AAT Children riding in the car should sit in the rear seat and must always be properly restrained to minimize the risk of injury in an accident, sudden stop or sudden maneuver. According to acci- dent statistics provided by the National High- way Traffic Safety Administration (NHTSA), children are safer when properly restrained in the rear seats than in the front seat. Larger children not in a child restraint should use one of the seat belts provided. All 50 states have child restraint laws. You should be aware of the specific requirements in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. You must use a commercially available child restraint system that meets the requirements of the Federal Motor Vehicle Safety Standards (FMVSS). Children could be injured or killed in a crash if their restraints are not properly secured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits your car and seat belts, and fits your child. Follow all the instructions provided by the manufacturer when installing the child restraint system. WARNING: o A child restraint system must be placed in the rear seat. Never install a child or infant seat on the front passenger's seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Thus only use a child restraint in the rear seat of your vehicle. o A safety belt or child restraint system can become very hot if it is left in a closed vehicle on a sunny day, even if the out- side temperature does not feel hot. Be sure to check the seat cover and buckles before placing a child there. o When the child restraint system is not in use, store it in the trunk or fasten it with a safety belt so that it will not be thrown forward in the case of a sudden stop or an accident. o Children may be seriously injured or killed by an inflating airbag. All children, even those too large for child restraints, must ride in the rear seat. FEATURES OF YOUR HYUNDAI 21 WARNING: To reduce the chance or serious or fatal injuries: o Children of all ages are safer when re- strained in the rear seat. A child riding in the front passenger seat can be force- fully struck by an inflating airbag result- ing in serious or fatal injuries. o Always follow the instructions for in- stallation and use of the child restraint maker. o Always make sure the child seat is se- cured properly in the car and your child is securely restrained in the child seat. o Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the car’s interior. o Never put a seat belt over yourself and a child. During a crash, the belt could press deep into the child causing seri- ous internal injuries. o Never leave children unattended in a vehicle – not even for a short time. The car can heat up very quickly, resulting in serious injuries to children inside. Even very young children may inadvertently cause the vehicle to move, entangle them- selves in the windows, or lock them- selves or others inside the vehicle. 1FEATURES OF YOUR HYUNDAI 22 WARNING: o Never allow two children, or any two persons, to use the same seat belt. o Children often squirm and reposition themselves improperly. Never let a child ride with the shoulder belt under their arm or behind their back. Always prop- erly position and secure children in rear seat. o Never allow a child to stand-up or kneel on the seat or floorboard of a moving vehicle. During a collision or sudden stop, the child can be violently thrown against the vehicles interior, resulting in serious injury. o Never use an infant carrier or a child safety seat that "hooks" over a seatback, it may not provide adequate security in an accident. o Seat belts can become very hot, espe- cially when the car is parked in direct sunlight. Always check seat belt buck- les before fastening them over a child. o Always store or secure a child seat, even when it is not in use. During a collision or sudden stop, the child seat could be thrown inside the vehicle. B230B02GK-GAT Using a Child Restraint System For small children and babies, the use of a child seat or infant seat is required. This child seat or infant seat should be of appropriate size for the child and should be installed in accordance with the manufacturer's instructions. It is further required that the seat be placed in the vehicle's rear seat since this can make an important contribution to safety. Your vehicle is provided with two child restraint hook holders for insta lling the child seat or infant seat. B230C05F-AAT Installing a Child Restraint Seat with the "Tether Anchorage" System Two child restraint hook holders are located on the luggage compartment floor. To install the child restraint seat Tether Anchor Cover Child Restraint Hook Holder B230E02GK 1. Open the tether anchor cover on the rear luggage compartment floor. 2. Route the child restraint seat strap over the seatback. For vehicles with adjustable headrests, route the tether strap under the headrest and between the headrest posts, otherwise route the tether strap over the top of the seatback. WARNING: o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use. o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death. Rear luggage compartment floor Blanking covers Covering shelf Child Restraint Hook Holders Tether strap hook Front of Vehicle B230E01GK 3. Remove the blanking covers on the cover- ing shelf. 4. Connect the tether strap hook to the child restraint hook holder through the hole on the covering shelf and tighten to secure the seat. FEATURES OF YOUR HYUNDAI 23 B230D03GK-AAT Securing the child Restraint seat with the "ISOFIX" system B230F01GK Some child seat manufacturers make child restraint seats that are labeled as ISOFIX or ISOFIX-compatible child restraint seats. These seats include two rigid or webbing mounted attachments that connect to two ISOFIX an- chors at specific seating positions in your ve- hicle. This type of child restraint seat eliminates the need to use seat belts to attach the child seat for forward-facing child restraint seats. ISOFIX anchors have been provided in your vehicle. The ISOFIX anchors are located in the left and right outboard rear seating positions. Their locations are shown in the illustration. 1FEATURES OF YOUR HYUNDAI 24 WARNING: o There is no center rear seat position. o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use. o Never install a child restraint using the ISOFIX anchors at the center position of the rear seat. In a crash, the ISOFIX anchors may break if a car seat is improp- erly placed in the center position result- ing in serious or fatal injuries. Only place a ISOFIX or ISOFIX-compatible child seat in the left or right out-board rear seating positions (as shown) to the appropriate ISOFIX anchors provided. o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death. o When using the vehicle’s “ISOFIX” sys- tem to install a child restraint system in the rear seat, all unused vehicle rear seat belt metal latch plates or tabs must be latched securely in their seat belt buck- les and the seat belt webbing must be retracted behind the child restraint to prevent the child from reaching and tak- ing hold of unretracted seat belts. Unlatched metal latch plates or tabs may allow the child to reach the unretracted seat belts which may result in strangu- lation and a serious injury or death to the child in the child restraint. ISOFIX Anchor ISOFIX Anchor Position Indicator B230D02GK The ISOFIX anchors are located between the seatback and the seat cushion of the rear seat left and right outboard seating positions. ! WARNING: A child can be seriously injured or killed in a collision if the child restraint is not prop- erly anchored to the car and the child is not properly restrained in the child restraint. Always follow the child seat manufacturer’s instructions for installation and use. HGK261 Follow the child seat manufacturer's instruc- tions to properly install child restraint seats with ISOFIX or ISOFIX-compatible attachments. Once you have installed the ISOFIX child re- straint, assure that the seat is properly attached to the ISOFIX and tether anchors. Also, test the child restraint seat before you place the child in it. Tilt the seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the seat in place. FEATURES OF YOUR HYUNDAI 25 B230G02O-AAT Child Restraint System Installation on outboard Rear Seats On outboard rear seats HGK1010 To install a child restraint system in the outboard rear seats, extend the shoulder/lap belt entirely from its retractor until a "click" is felt. This will engage the seat belt retractor automatic locking feature, which allows the seat belt to retract but not extend. Install the child restraint system, buckle the seat belt and allow the seat belt to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint system and the shoulder portion of the belt is positioned so that it can not interfere with the child's head or neck. Also, double check to be sure that the retractor has engaged the auto- matic locking feature by trying to extend web- bing out of the retractor. 1FEATURES OF YOUR HYUNDAI 26 If the retractor is in the automatic locking mode, the belt will be locked. After installation of the child restraint system, try to move it in all directions to be sure the child restraint system is securely installed. If you need to tighten the belt, pull more webbing toward the retractor. When you unbuckle the seat belt and allow it to retract, the retractor will automatically revert back to its normal seated passenger emer- gency locking usage condition. NOTE: o Before installing the child restraint sys- tem in any seating position, read the instructions supplied by the child re- straint system manufacturer. o If the seat belt does not operate as de- scribed, have the system checked imme- diately by your authorized Hyundai dealer. ! WARNING: o If the retractor is not in the Automatic Locking mode, the child restraint can move when your vehicle turns or stops suddenly. A child can be seriously in- jured or killed if the child restraint is not properly anchored to the car, including setting the retractor to the Automatic Locking mode. o Do not install any child restraint system in the front passenger seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Therefore, only use a child restraint system in the rear seat of your vehicle. B180B04GK-AAT Pre-tensioner Seat Belt (If Installed) Your Hyundai vehicle is equipped with driver's and front passenger's pre-tensioner seat belts. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against the occupant's body in certain frontal collisions. The pre-tensioner seat belts can be activated alone or, where the frontal collision is severe enough, together with the airbags. HXG229 When the vehicle stops suddenly, or if the occupant tries to lean forward too quickly, the seat belt retractor will lock into position. In certain frontal collisions, the pre-tensioner will activate and pull the seat belt into tighter contact against the occupant's body. Driver's airbag Passenger's airbag WARNING: To obtain maximum benefit from a pre- tensioner seat belt: o The seatbelt must be work correctly and adjusted to the proper position (see pages 1-18). Please read and follow all of the important information and precau- tions about your vehicle’s occupant safety features – including seat belts – that are provided in this manual. o Be sure you and your passengers always wear seat belts and wear them properly. B180B01GK The seat belt pre-tensioner system consists mainly of the following components. Their locations are shown in the illustration. 1. SRS airbag warning light 2. Seat belt pre-tensioner assembly 3. SRS control module FEATURES OF YOUR HYUNDAI 27 NOTE: o Both the driver's and front passenger's pre-tensioner seat belts will be activated in certain frontal collisions. The pre- tensioner seat belts can be activated alone or, where the frontal collision is severe enough, together with the airbags. o When the pre-tensioner seat belts are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger com- partment. These are normal operating conditions and are not hazardous. o Although it is harmless, the fine dust may cause skin irritation and should not be breathed for prolonged periods. Wash all exposed skin areas thoroughly after an accident in which the pre-tensioner seat belts were activated. 1FEATURES OF YOUR HYUNDAI 28 CAUTION: AIR BAG o The sensor that activates the SRS airbag is connected with the pre-tensioner seat belts. The SRS airbag warning light on the instrument panel will illuminate for approximately 6 seconds after the igni- tion key has been turned to the "ON" position, and then it should turn off. o If the pre-tensioner seat belt is not work- ing properly, this warning light will illu- minate even if there is no malfunction of the SRS airbag system. If the SRS airbag warning light does not illuminate when the ignition key is turned to "ON" or if it remains illuminated after approximately 6 seconds, or if it illuminates while the vehicle is being driven, please have an authorized Hyundai dealer inspect the pre-tensioner seat belts and SRS airbag system as soon as possible. WARNING: o Pre-tensioners are designed to operate only one time. After activation, pre- tensioner seat belts must be replaced. All seat belts, of any type, should always be replaced after they have been worn during a collision. o The pre-tensioner seat belt assembly mechanisms become hot during activa- tion. Do not touch the pre-tensioner seat belt assemblies for several minutes after they have been activated. o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. This must be done by an authorized Hyundai dealer. o Do not strike the pre-tensioner seat belt assemblies. o Do not attempt to service or repair the pre-tensioner seat belt system in any manner. o Improper handling of the pre-tensioner seat belt assemblies, and failure to heed the warnings to not strike, modify, in- spect, replace, service or repair the pre- tensioner seat belt assemblies may lead to improper operation or inadvertent activation and serious injury. o Always wear seat belts when driving or riding in a motor vehicle. SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS) B240A03GK-AAT Driver's Airbag B240A01GK Your Hyundai is equipped with a Supplemental Restraint (Airbag) System. The indications of the system's presence are the letters "SRS AIR BAG" embossed on the ornament in the steer- ing wheel and the passenger's side front panel pad above the glove box. The Hyundai SRS consists of airbags installed under the pad covers in the center of the steering wheel and the passenger's side front panel above the glove box. The purpose of the SRS is to provide the vehicle's driver and/or the front passenger with additional protection than that offered by the seat belt system alone, in case of a frontal impact of sufficient severity. NOTE: o Be sure to read information about the SRS on the labels provided on the front of the sun visor and in the glove box. o If you are considering modification of your vehicle due to a disability, please contact the Hyundai Customer Assis- tance Center at 1-800-633-5151. WARNING: Always use seat belts and child restraints – every trip, every time, everyone! Airbags inflate with considerable force and in the blink of an eye. Seat belts help keep occu- pants in proper position to obtain maxi- mum benefit from the airbag. Always fol- low the precautions about seat belts, airbags and occupant safety contained in this manual. To reduce the chance of serious or fatal injuries and receive the maximum safety benefit from your restraint system: o Never place a child in any child or booster seat in the front seat (see child restraints 1-21). o ABC – Always Buckle Children in the back seat. It is the safest place for children of any age to ride o Front and side impact airbags can injure occupants improperly positioned in the front seats WARNING: o Move your seat as far back as practical from the front airbags, while still main- taining control of the vehicle. o Never sit or lean unnecessarily close to the front or side airbags o Never lean against the door or center console – always sit in an upright posi- tion o Never place objects over or near any airbag module (front or side impact airbags), because these objects can in- jure passengers in a crash o Never place covers, blankets or after- market seat warmers on the passenger seat as these may interfere with the occupant classification system o Do not tamper or disconnect SRS wiring or other components. Injuries could result from inadvertent deployment or failure of the airbag to deploy in a crash. o If the SRS airbag warning light (see pg 1- 40) remains illuminated while the vehicle is being driven, have an authorized Hyundai dealer inspect the airbag sys- tem as soon as possible. o Airbags can only be used once – have an authorized Hyundai dealer replace the airbag immediately after deployment. FEATURES OF YOUR HYUNDAI 29 WARNING: o The SRS is designed to deploy the airbags only when an impact is suffi- ciently severe and when the impact angle is less than 30° from the forward longi- tudinal axis of the vehicle and will not deploy in side, rear or rollover impacts. Additionally, the airbags will only de- ploy once. Thus, seat belts must be worn at all times. o Front airbags are not intended to deploy in light collisions in which protection can be provided by the seat belt alone. Rear impact Side Impact Rollover B240A02GK 1FEATURES OF YOUR HYUNDAI 30 WARNING: o Front airbags are not intended to deploy in side-impact, rear-impact or rollover crashes. In addition, airbags will not deploy in frontal crashes below the de- ployment threshold speed. o Move your seat as far back as practical from the front airbags, while still main- taining control of the vehicle. You and your passengers should never sit or lean unnecessarily close to the airbags. Im- properly positioned drivers and passen- gers can be severely injured by inflating airbags. o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to deploy. o If the airbags deploy, they must be re- placed by an authorized Hyundai dealer. Deployed airbags WILL NOT inflate again and will provide no protection in subse- quent collisions. o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental firing of the airbags or by rendering the SRS inoperative. WARNING: o Do not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident. o Do not allow children to ride in the front passengrer seat. If older children (teen- agers and older) must ride in the front seat, make sure they are always properly belted and that the seat is moved back as far as possible. o For maximum safety protection in all types of crashes, all occupants includ- ing the driver should always wear their seat belts whether or not an airbag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. Do not sit or lean unnecessarily close to the airbag while the vehicle is in motion. o The SRS airbag system must deploy very rapidly to provide protection in a crash. If an occupant is out of position because of not wearing a seat belt, the airbag may forcefully contact the occupant causing serious or fatal injuries. B240B04GK-AAT SRS Components and Functions The SRS consists of the following components: B240B01L - Driver's Airbag Module - Passenger's Airbag Module - Knee Bolster - SRS Service Reminder Indicator (SRI) - SRS Control Module (SRSCM) The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontal or near-frontal impact is severe enough to require airbag deployment. FEATURES OF YOUR HYUNDAI 31 Passanger's Airbag B240B03L B240B01GK A fully inflated airbag in combination with a properly worn seat belt slows the driver's or the passenger's forward motion, thus reducing the risk of head and chest injury. After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility. CAUTION: Do not install or place any accessories (drink holder, cassette holder, sticker, etc) on the front passenger's panel above the glove box in a vehicle with a passenger's air bag. Such objects may become dangerous projectiles and cause injury if the passenger's air bag inflates. The SRS service reminder indicator (SRI) on the instrument panel will illuminate for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which the SRI should go out. B240B02L The airbag modules are located both in the center of the steering wheel and in the front passenger's panel above the glove box. When the SRSCM detects a considerable impact to the front of the vehicle, it will automatically deploy the airbags.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Hyundai Tiburon Owners Manual