Download PDF Manual


! WARNING:


Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances. Continued driving on low pressure tires will cause the tires to overheat and fail.


TPMS (Tire Pressure Monitor- ing System) malfunction indi- cator


TPMS malfunction indicator comes on for 3
seconds after the ignition key is turned to the "ON" position. If the warning light does not come on, or continuously remains on after coming on for about 3 seconds when you turned the ignition key to the "ON" position, the Tire Pressure Monitoring System is not working properly. If this occurs, have your vehicle checked by an authorized Hyundai dealer as soon as possible. The warning light also comes on and stays on when there is a problem with the Tire Pressure Monitoring System. If this happens, the system may not monitor the tire pressure. Have the system checked by an authorized Hyundai dealer as soon as possible.


WARNING:


o The TPMS cannot alert you to severe and sudden tire damage caused by external factors.


o If you feel any vehicle instability, imme- diately take your foot off the accelerator and slowly move to a safe position off the road.


gkflhma-1a.p65


48


9/12/2006, 3:16 PM


B260J01A-AAT


B260B01JM-AAT


B260E02L-AAT


FEATURES OF YOUR HYUNDAI


49


Charging System Warning Light


SRS (Airbag) Warning Light


The charging system warning light should come on when the ignition is turned on, then go out when the engine is running. If the light stays on while the engine is running, there is a malfunc- tion in the electrical charging system. If the light comes on while you are driving, stop, turn off the engine and check under the hood. First, make certain the generator drive belt is in place. If it is, check the tension of the belt. Do this as shown on page 6-19 by pushing down on the center of the belt. Have the system checked by your Hyundai dealer as soon as possible.


The SRS service reminder indicator (SRI) comes on for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which it will go out.


This light also comes on when the SRS is not working properly. If the SRI does not come on, or continuously remains on after coming on for about 6 seconds when you turned the ignition key to the "ON" position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai Dealer.


Seat Belt Reminder Light And Chime


Seat belt reminder light comes and stays on until the seat belt is fastened when the ignition key is turned to "ON" or "START". And, the warning chime will also sound for about 6 seconds.


B260F01A-AAT


High Beam Indicator Light


The high beam indicator light comes on when- ever the headlights are switched to the high beam or flash position.


gkflhma-1a.p65


49


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 50


B260G01A-AAT


B260N02A-AAT


B260H02GK-AAT


Low Oil Pressure Warning Light


Malfunction Indicator Light


Parking Brake/Low Brake Fluid Level Warning Light


CAUTION:


If the oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pressure warn- ing light comes on whenever there is insuf- ficient oil pressure. In normal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there is a serious malfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off imme- diately. In any instance where the oil light stays on when the engine is running, the engine should be checked by a Hyundai dealer before the car is driven again.


This light illuminates when there is a malfunction of an exhaust gas related component, and the system is not functioning properly so that the exhaust gas regulation values are not satisfied. This light will also illuminate when the ignition key is turned to the "ON" position, and then it will go out in a few seconds after the engine is started. If it illuminates while driving, or does not illumi- nate when the ignition key is turned to the "ON" position, take your car to your nearest autho- rized Hyundai dealer and have the system checked.


B260M01A-AAT


Low Fuel Level Warning Light


The low fuel level warning light comes on when the fuel tank is approaching empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below "E" can cause the engine to misfire and damage the catalytic converter.


CAUITON:


If you suspect brake trouble, have your brakes checked by a Hyundai dealer as soon as possible. Driving your car with a problem in either the brake electrical sys- tem or brake hydraulic system is danger- ous, and could result in a serious injury or death.


Warning Light Operation


The parking brake/low brake fluid level warning light should come on when the parking brake is applied and the ignition switch is turned to "ON" or "START". After the engine is started, the light should go out when the parking brake is re- leased. If the parking brake is not applied, the warning light should come on when the ignition switch is turned to "ON" or "START", then go out in three seconds. If the light comes on at any other time, you should slow the vehicle and bring it to a complete stop in a safe location off the roadway.


gkflhma-1a.p65


50


9/12/2006, 3:16 PM


The brake fluid level warning light indicates that the brake fluid level in the brake master cylinder is low and hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications should be added. After adding fluid, if no other trouble is found, the car should be immediately and care- fully driven to a Hyundai dealer for inspection. If further trouble is experienced, the vehicle should not be driven at all but taken to a dealer by a professional towing service. Your Hyundai is equipped with dual-diagonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only half of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.


FEATURES OF YOUR HYUNDAI


51


B260Q01E-GAT


B260K01F-AAT


Tail Gate Open Warning Light


This light remains on unless the tail gate is completely closed and latched.


CRUISE Indicator Light (If Installed)


The cruise indicator light in the instrument clus- ter is illuminated when the cruise control main switch on the end of the barrel is pushed. The indicator light does not illuminate when the cruise control main switch is pushed a second time. Information about the use of cruise control is beginning on page 1-80.


B260R01E-GAT


B260L02HP-GAT


CRUISE SET Indicator Light (If installed)


Door Ajar Warning Light and Chime


The set indicator light in the instrument cluster is illuminated when the cruise control switch is pushed downward to "SET (COAST)". The set indicator light does not illuminate when the control switch is in the "CANCEL" position.


The door ajar warning light warns you that a door is not completely closed and the chime warns you that the key is in the ignition switch. NOTE : The warning chime only sounds whenever the key is in the ignition switch and the driver's side front door is open simulta- neously. The chime sounds until the key is removed from the ignition switch or the driver's side front door is closed.


gkflhma-1a.p65


51


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 52


B260P02Y-GAT


ABS Service Reminder Indica- tor (SRI)


When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on and then go off in a few seconds. If the ABS SRI remains on, comes on while driving, or does not come on when the key is turned to the "ON" position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by your Hyundai dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.


WARNING:


If the both ABS SRI and Parking Brake/ Brake fluid level warning lights remain "ON" or come on while driving, there may be a problem with E.B.D (Electronic Brake Force Distribution). If this occurs, avoid sudden stops and have your vehicle checked by your Hyundai dealer as soon as possible.


INSTRUMENT CLUSTER


B270A01A-AAT Brake Pad Wear Warning Sound


B280A01TG-AAT Fuel Gauge


The front disc brake pads have wear indicators that should make a high-pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Excessive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.


OGK016259


The needle on the gauge indicates the approxi- mate fuel level in the fuel tank. The fuel capacity is given in Section 9.


NOTE: The " is placed on the left side of the vehicle.


" symbol means the fuel filler lid


gkflhma-1a.p65


52


9/12/2006, 3:16 PM


B290A02A-AAT Engine Coolant Temperature Gauge


B300A01A-AAT Speedometer


The needle on the engine coolant temperature gauge should stay in the normal range. If it moves across the dial to "H" (Hot), pull over and stop as soon as possible and turn off the engine. Then open the hood and after the engine has cooled, check the coolant level and the water pump drive belt. If you suspect cooling system trouble, have your cooling system checked by a Hyundai dealer as soon as possible.


FEATURES OF YOUR HYUNDAI


53


OGK016261


OGK016264
Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilome- ters per hour (on the inner scale).


WARNING:


Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before removing the radiator cap.


gkflhma-1a.p65


53


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 54


B330A03E-AAT Tachometer


The tachometer registers the speed of your engine in revolutions per minute (rpm).


OGK016265


CAUTION:


The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.


B310B02GK-AAT Odometer/Trip odometer Type A


Type A


Type B


Type B


HGK2061-1


HGK028B Function of digital odometer/trip odom- eter Pushing in the reset switch on the right side of the speedometer when the ignition switch is turned "ON" will display the following sequence:


HGK055C


gkflhma-1a.p65


54


9/12/2006, 3:16 PM


1. Odometer


The odometer records the total driving distance in miles, and is useful for keeping a record for maintenance intervals.


NOTE: Any alteration of the odometer may void your warranty coverage.


2,3 Trip odometer


Records the distance of 2 trips in miles. TRIP A: Distance you have traveled from your origination point to a first destination. TRIP B: Distance from the first destination to the final destination.


To shift from TRIP A to TRIP B, press the reset switch. When pressed for 1 second, it will reset to 0.


TRIP COMPUTER


B400B04GK-AAT (If installed)


Type A


Type B


OGK016400N


The trip computer is a microcomputer-con- trolled driver information gauge that displays information related to driving, such as estimated distance to empty, average speed and drive time on the LCD.


FEATURES OF YOUR HYUNDAI


55


Reset Switch


o The reset switch is used to zero the multi-


functional display mode.


o Pushing in the reset switch on the left side of the tachometer changes the display as follows;


DISTANCE TO EMPTY


AVERAGE SPEED


DRIVE TIME


gkflhma-1a.p65


55


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 56


Type A


Type B


OGK016401N


1. Distance to Empty o This mode provides the estimated distance to empty from the current fuel level in the fuel tank.


o The trip computer may not register additional fuel if less than 1.36 gallons (6 liters) of fuel are added to the vehicle.


o When the battery has been reinstalled after being discharged or disconnected, drive more than 20 miles (32km) for an accurate distance to empty.


Type A


Type B


2. Average Speed


Type A


Type B


OGK046033N


o When the distance to empty is less than 31
miles (50 km), the symbol will always come on and the distance to empty digits will indicate "---" with flash until more fuel is added.


NOTE: o The distance to empty can differ from the actual tripmeter according to driving conditions.


o The distance to empty can vary accord- ing to the driving conditions, driving pattern or vehicle speed.


OGK016402N


o This mode indicates the average speed travelled since the last average speed reset. o To reset the average speed to zero, press and hold the reset switch for more than 1
second while the average speed is being displayed.


gkflhma-1a.p65


56


9/12/2006, 3:16 PM


3. Drive Time


Type A


Type B


OGK016403N


o This mode indicates the drive time travelled


since the last drive time reset.


o To reset the drive time to zero, press and hold the reset switch for more than 1 second while the drive time is being displayed.


MULTI GAUGE


B330C02GK-GAT (If installed)


The multi gauge consists of a torque gauge, instantaneous fuel consumption gauge, and volt meter.


FEATURES OF YOUR HYUNDAI


57


B330C04GK


Instantaneous fuel Consumption gauge


It shows instantaneous fuel consumption ac- cording to driving conditions. The more indi- cated figure is low, the more it indicates efficient driving situation.


B330C01GK


Torque gauge


It shows instantaneous change of the torque by rpm.


gkflhma-1a.p65


57


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 58


B330C03GK


Volt gauge


It shows moment volt change and makes for diver correspond to low volt situation.


MULTI-FUNCTION LIGHT SWITCH


B340A01A-AAT Combination Turn Signal, Headlight and High-beam Switch Turn signal operation


Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned- out fuse or bulb or see your Hyundai dealer.


B340B01A-AAT Lane Change Signal


HGK2079


To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.


gkflhma-1a.p65


58


9/12/2006, 3:16 PM


B340C03E-AAT Headlight Switch


HGK2074


To operate the headlights, turn the barrel on the end of the multi-function switch. The first posi- tion turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights.


NOTE: The ignition must be in the "ON" position to turn on the headlight.


Parking light auto cut


o The purpose of this feature is to prevent the battery from being discharged. The system automatically turns off the parking light when the driver removes the ignition key and opens the driver- side door.


o With this feature, the parking light will be turned off automatically if the driver parks on the side of road at night.


If necessary, to keep the lights on when the ignition key is removed, perform the following : 1) Open the driver-side door. 2) Turn the parking light OFF and ON again using the light switch on the steering column.


B340D01A-AAT High-beam Switch


To turn on the headlight high beams, push the lever forward (away from you). The high beam indicator light will come on at the same time. For low beams, pull the lever back toward you.


FEATURES OF YOUR HYUNDAI


59


B340G02LZ-GAT Auto Light (If installed)


OGK026223N


To operate the automatic light feature, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automati- cally on or off according to external illumination.


NOTE: Switch on head light manually in foggy, cloudy and rainy conditions.


gkflhma-1a.p65


59


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 60


B340E01A-AAT Headlight Flasher


WINDSHIELD WIPER AND WASHER SWITCH


B350A01A-AAT


Auto Light Sensor


OGK026223C


NOTE: o Never place anything over the sensor located on the instrument panel, to en- sure better auto light system control.


o Don't clean the sensor using a window


cleaner.


o If your vehicle has window tint or other types of coating on the front windshield, the AUTO light system may not work properly.


HGK2077


To flash the headlights, pull the switch lever toward you, then release it. The headlights can be flashed even though the headlight switch is in the "OFF" position.


The windshield wiper switch has three posi- tions:


OGK047046N


(1) Intermittent wiper operation (2) Low-speed operation (3) High-speed operation


NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accumula- tions of snow or ice. Accumulated snow and ice should be removed manually. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper.


gkflhma-1a.p65


60


9/12/2006, 3:16 PM


B350B01O-AAT Windshield Washer Operation


Mist Wiper Operation


B350C01S-AAT Adjustable Intermittent Wiper Operation


FEATURES OF YOUR HYUNDAI


61


OGK047048N To use the windshield washer, pull the wiper/ washer lever toward the steering wheel. When the washer lever is operated, the wipers auto- matically make two passes across the wind- shield. The washer continues to operate until the lever is released.


OGK047049N If a single wipe is desired in mist, move the windshield wiper and washer control lever up.


OGK047050N


To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval between wipes can be varied from 2 to 10 seconds by turning the interval adjuster barrel.


NOTE: o Do not operate the washer more than 15
seconds at a time or when the fluid reservoir is empty.


o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers.


o In areas where water freezes in winter,


use windshield washer antifreeze.


gkflhma-1a.p65


61


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI 62


B390A01E-AAT Rear Window Wiper And Washer Switch


FRONT FOG LIGHT SWITCH


B360A04A-AAT


Do not operate the washer continuously for more than 15 seconds or when the fluid reser- voir is empty; this could damage the system. Do not operate the wiper when the window is dry; this can result in scratching as well as prema- ture wiper blade wear. For the reason stated above,do not operate the washer when the washer fluid reservoir is empty.


1.


5.


OGK047051N : The rear window wiper starts to oper- ate three times after the washer fluid sprays onto the rear window.


2.OFF 3.INT : The interval between wipes operates


every 5 seconds intermittently.


4.ON : The rear window wiper starts to oper-


ate continuously.


: The washer fluid will be sprayed onto the rear window and the wiper operates while the rear window wiper barrel is placed in this position.


OGK046052
To turn on the front fog lights, push the switch. They will light when the headlight switch is in the second position and the ignition key is in the "ON" position.


NOTE: If you turn on the headlight high beams, the front fog lights will be turned off.


gkflhma-1a.p65


62


9/12/2006, 3:16 PM


HAZARD WARNING SYSTEM


B370A01A-AAT


REAR WINDOW DEFROSTER SWITCH


B380A02A-AAT


Type A


FEATURES OF YOUR HYUNDAI


63


CAUTION:


Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster elements.


OGK066001
The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push the switch a second time.


Type B


NOTE: The engine must be running for the rear window defroster to operate.


OGK046054-1N


The rear window defroster and heated outside rearview mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window defroster automatically turns itself off after about 20 min- utes. To restart the defroster cycle, push in the switch again after it has turned itself off.


gkflhma-1a.p65


63


9/12/2006, 3:16 PM


1FEATURES OF YOUR HYUNDAI DIGITAL CLOCK 64


INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)


CIGARETTE LIGHTER


B400A01A-AAT


B410A01A-AAT


B420A02A-AAT


OGK046056


OGK046029


The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob.


There are three control buttons for the digital clock. Their functions are: H - Push "H" to advance the hour indicated. M - Push "M" to advance the minute indicated. R - Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done: Pressing "R" between 11 : 01 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 11 : 59
changes the readout to 12 : 00. Push the "R" button for 3 seconds to display a 12 or 24-hour clock.


OGK046078
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.


CAUTION:


Do not use electric accessories or equip- ment other than the Hyundai genuine parts in the socket.


gkflhma-1a.p65


64


9/12/2006, 3:17 PM


ASHTRAY


DRINK HOLDER


B430A01GK-AAT


B450A02GK-AAT


FEATURES OF YOUR HYUNDAI


65


WARNING:


o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electrical components.


o Do not place objects other than cups or cans in the drink holder. Such objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.


OGK046077
The front ashtray may be opened by pushing and releasing the ashtray door at its top edge. To remove the ashtray in order to clean it, the metal ash receptacle should be lifted out from the ashtray door. Do not attempt to remove the entire ashtray door assembly or damage will result. To reinstall it, place it in the proper position and press it down in the ashtray door. The ashtray lamp will only illuminate when the exterior body lights are switched on.


OGK046079
The drink holder is used for holding cups or cans. To use the passenger's drink holder, push the drink holder.


gkflhma-1a.p65


65


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 66


SUNSHADE


B470A01GK-AAT (If Installed)


SUNROOF


B460A01S-AAT (If Installed)


The sunroof can be operated with the ignition key in the "ON" position.


B460B03GK-GAT Opening the Sunroof System


OGK046019
The sunshade can be opened and closed by sliding it forward or rearward when the sunroof is closed. The sunshade will open automatically when the sunroof is opened, but it must be closed manually.


WARNING:


Never adjust the sunshade while driving. This could result in loss of control and an accident that may cause death, serious injury, or property damage.


OGK046017
The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its fully open position by pushing the " " switch, and to stop at the desired position, push in any switches ( , , Up, Down). To close, press and hold the " " button. Release the button when the sunroof reaches the desired position.


WARNING:


Be careful that someone’s head, hands and body are not trapped by a closing sunroof.


gkflhma-1a.p65


66


9/12/2006, 3:17 PM


FEATURES OF YOUR HYUNDAI


67


B460D03GK-AAT Manual Operation of Sunroof


If the sunroof does not electrically operate:


OGK046020
1. Remove the cap located in the rear roof


panel by using a coin or screw driver.


B460C01GK-AAT Tilting the Sunroof System


WARNING:


o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.


o Do not place your head or arms out of the


sunroof opening at any time.


o While the vehicle is moving, always keep the head, hands and other parts of the body of all occupants away from the roof opening. Otherwise, you could be seri- ously injured if the vehicle stops sud- denly or if the vehicle is involved in an accident.


CAUTION:


o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.


o Periodically remove any dirt that may


have accumulated on the guide rails.


o Do not press any sunroof control button


longer than necessary. Damage to the motor or system compo- nents could occur.


OGK046018
To use the auto tilt feature, press the UP button on the overhead console. The sunroof will tilt all the way open. To stop the sunroof tilting at any point, press any sunroof control button.


To close the sunroof, press the DOWN button on the overhead console and hold it until the sunroof is closed.


NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.


gkflhma-1a.p65


67


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 68


B460E04GK-AAT Resetting the Sunroof System


B480A02GK-GAT Map Light


INTERIOR LIGHT


If the battery has been recharged, discon- nected or the sunroof was been opened manu- ally with the hexagonal head wrench, you may need to reset the sunroof.


To do this; 1. Turn the ignition switch "OFF". 2. While pressing " " "up" button turn the


ignition switch "ON".


The resetting was not occur when the ignition key is turned "OFF" within 1.5
seconds.


3.


If the sunroof is set like this, the sunroof is reset with tilting up/down automatically once for all.


OGK046021


2.


Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle’s trunk or glove box.


3. Push and turn the wrench clockwise to close or counterclockwise to open the sunroof.


CAUTION:


If the sunroof is not reset, it may not operate normally.


OGK046034L-1


(1) Push in the map light switch to turn on the


driver side light.


(2) In the "DOOR" position, the interior cour- tesy light comes on when any door is opened regardless of the ignition key posi- tion. The light goes out gradually 6 seconds after the door is closed.


(3) Push in the map light switch to turn on the


front passenger side light.


gkflhma-1a.p65


68


9/12/2006, 3:17 PM


SUNGLASS HOLDER


GLOVE BOX


B491A02F-AAT


B500A01A-AAT


FEATURES OF YOUR HYUNDAI


69


B500B01NF-GAT Illuminated Glove Box


Opening the glove box will automatically turn on the light when the multi-function switch is turned to the first position.


OGK046076


OGK046075


The sunglass holder is located on the front overhead console. Push the end of the cover to open or close the sunglass holder.


WARNING:


o Do not keep objects except sunglass inside the sunglass holder. Such ob- jects can be thrown from the holder in the event of a sudden stop or an acci- dent, possibly injuring the passengers in the vehicle.


o Do not open the sunglass holder while the vehicle is moving. The rear view mirror of the vehicle can be blocked by an open sunglass holder.


WARNING:


To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.


o To open the glove box, pull on the glove box


release lever.


gkflhma-1a.p65


69


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 70


OUTSIDE REAR VIEW MIRROR


B510B02A-AAT Electric Type


2. Next, adjust the mirror angle by depressing the appropriate perimeter switch as illus- trated.


B510D01HP-AAT Outside Rearview Mirror Heater (If Installed)


OGK046026L The outside rearview mirrors can be adjusted to your preferred rear vision, both directly be- hind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both the right and left outside mirrors.


To adjust the position of either mirror:


1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.


CAUTION:


o Do not operate the switch continuously


for an unnecessary length of time.


o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved deicer.


WARNING:


Be careful when judging the size or dis- tance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.


Type A


Type B


OGK046054-1N


The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 20 minutes.


gkflhma-1a.p65


70


9/12/2006, 3:17 PM


DAY/NIGHT INSIDE REAR VIEW MIRROR


FEATURES OF YOUR HYUNDAI


71


B510C02A-AAT Folding the Outside Rear View Mirrors


B520A01A-AAT Manual Type


B520B02O-GAT Electric type (If installed)


HGK2055


OGK046024


To fold the outside rear view mirrors, push them toward the rear. The outside rear view mirrors can be folded rearward for parking in narrow areas.


Your Hyundai is equipped with a day/night inside rear view mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.


WARNING:


Do not adjust or fold the outside rear view mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause serious injury or death.


OGK046025
The electric type day/night inside rearview mir- ror automatically controls the glare of headlights of the car behind you.


1. Pressing the button turns the auto- dimming function OFF which is indicated by the green Status Indicator LED turning off. 2. Pressing the button again turns the auto- dimming function ON which is indicated by the green Status Indicator LED turning on.


NOTE: The mirror defaults to the "ON" position each time the vehicle is started.


gkflhma-1a.p65


71


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI PARKING BRAKE 72


B530A03A-AAT


CAUTION:


Driving with the parking brake applied will cause excessive brake pad (or lining) and brake rotor wear.


Releasing the parking brake


To release the parking brake, first apply the foot brake and pull up the parking brake lever slightly. Secondly, depress the release button and lower the parking brake lever while holding the button.


WARNING:


Whenever leaving vehicle or parking always set the parking brake as far as possible and fully engage the vehicle's transaxle into the park position. Vehicles not fully engaged in park with the parking brake set are at risk for moving inadvertently and injuring yourself or others.


OGK056005


Always engage the parking brake before leav- ing the car. This also turns on the parking brake indicator light when the key is in the "ON" or "START" position. Before driving away, be sure that the parking brake is fully released and the indicator light is off.


Applying the parking brake


To engage the parking brake, first apply the foot brake and then without pressing the release button in, pull the parking brake lever up as far as possible. In addition it is recommended that when parking the vehicle on a gradient, the shift lever should be positioned in the appropriate low gear on manual transaxle vehicles or in the P (Park) position on automatic transaxle vehicles.


HIGH-MOUNTED REAR STOP LIGHT


B550A01S-GAT


Type A


Type B


Type C


OGK016550L


In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.


gkflhma-1a.p65


72


9/12/2006, 3:17 PM


FRONT DOOR EDGE WARNING LIGHT B620A01S-AAT


HOOD RELEASE


B570A01GK-GAT


FEATURES OF YOUR HYUNDAI


73


B620A01GK


Hood Release Lever


OGK046011L


A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.


1. Pull the release knob to unlatch the hood.


OGK046012L 2. Press the safety hook lever up and lift the


hood.


3. Raise the hood by hand.


gkflhma-1a.p65


73


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 74


REMOTE FUEL-FILLER LID RELEASE


When closing the hood, slowly close the hood and make sure it locks into place.


B560A02MC-AAT


WARNING:


o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.


o Do not move the vehicle with the hood in the raised position, as vision is ob- structed and the hood could fall or be damaged.


OGK046013


The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.


NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved deicer fluid (do not use radiator anti-freeze) or move the ve- hicle to a warm place and allow the ice to melt.


OGK046014


WARNING:


o Gasoline vapors are dangerous. Before refueling, always stop the engine and never smoke or allow sparks and open flames near the filler area.


o Never operate your vehicle without a filler cap properly installed, flammable vapors and gasoline could leak out in dangerous situations such as a collision or rollover. If the filler cap must be replaced, only use genuine Hyundai re- placement parts.


o After refueling, make sure the fuel cap is installed securely to prevent fuel spill- age in the event of an accident.


o Tighten the cap until it clicks, otherwise


the "


"light will illuminate.


gkflhma-1a.p65


74


9/12/2006, 3:17 PM


!


WARNING:


o If you open the fuel filler cap during high ambient temperatures, a slight "pres- sure sound" may be heard. This is nor- mal and not a cause for concern. When- ever you open the fuel filler cap, turn it slowly.


o Do not "top off" after the nozzle auto-


matically shuts off when refueling.


o Automotive fuels are flammable/explo- sive materials. When refueling, please note the following guidelines carefully. Failure to follow these guidelines may result in severe personal injury, severe burns or death by fire or explosion. - Before refueling always note the loca- tion of the Emergency Gasoline Shut- Off, if available, at the gas station facility.


- Before touching the fuel nozzle or fuel filler cap, you should eliminate poten- tially dangerous static electricity dis- charge by touching another metal part of the front of the vehicle, a safe dis- tance away from the fuel filler neck, nozzle, or other gas source.


- Do not get back into a vehicle once you have begun refueling. Do not touch, rub or slide against any item or fabric (polyester, satin, nylon, etc.)


FEATURES OF YOUR HYUNDAI


75


WARNING:


- When refueling always shut the en- gine off. Sparks produced by electri- cal components related to the engine can ignite fuel vapors causing a fire. Always insure that the engine is OFF before and during refueling. Once re- fueling is complete, check to make sure the fuel filler cap and door are securely closed, before starting the engine.


- Do not light any fire around a gas station. DO NOT use matches or a lighter and DO NOT SMOKE or leave a lit cigarette in your vehicle while at a gas station especially during refuel- ing. Automotive fuel is highly flam- mable and can, when ignited, result in explosion by flames. If a fire breaks out during refueling, leave the vicinity of the vehicle, and immediately contact the manager of the gas station or contact the police and local fire department. Follow any safety instructions they provide.


! WARNING:


capable of producing static electric- ity. Static electricity discharge can ignite fuel vapors resulting in explo- sion. If you must re-enter the vehicle, you should once again eliminate poten- tially dangerous static electricity dis- charge by touching a metal part of the vehicle, away from the fuel filler neck, nozzle or other gasoline source.


- When using a portable fuel container be sure to place the container on the ground prior to refueling. Static elec- tricity discharge from the container can ignite fuel vapors causing a fire. Once refueling has begun, contact with the vehicle should be maintained until the filling is complete. Use only portable fuel containers designed to carry and store gasoline.


- Do not use cellular phones around a gas station or while refueling any ve- hicle. Electric current and/or electronic interference from cellular phones can potentially ignite fuel vapors causing a fire. If you must use your cellular phone use it in a place away from the gas station.


gkflhma-1a.p65


75


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 76


TAIL GATE


B540A01F-AAT Remote Tail Gate Release


WARNING:


The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-2.


B540C01F-AAT To Unlock Using the Key


OGK046005
To open the tail gate without using the key, pull up the lid release lever located on the driver's door panel. To close, lower the tail gate, then press down on it until it locks. To be sure the tail gate is securely fastened, always try to pull it up again.


OGK046006
To open the tail gate, insert the key and turn it clockwise to unlock. The tail gate compartment light illuminates when the tail gate is opened.


gkflhma-1a.p65


76


9/12/2006, 3:17 PM


B540D01GK-GAT when you close the tailgate


WARNING:


Do not close an open tailgate (rear hatch) while a person(s) is sitting upright on the rear seat. The tailgate or tailgate glass may contact the head of a person sitting upright on the rear seat. Closing the tailgate onto a person's head may cause serious injuries, including death.


OGK016540


HGK227


FEATURES OF YOUR HYUNDAI


77


SUN VISOR


B580A01GK-AAT


Vanity mirror


HGK2119
Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To reduce glare or to shut out direct rays of the sun, turn the sun visor down. A ticket holder is provided on the back of the sun visor for the driver. Vanity mirrors are provided on the back of the sunvisor for the driver and the front passenger (If Installed). NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the front of each sun visor.


gkflhma-1a.p65


77


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 78


WARNING:


Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.


B580C01JM-AAT Sun Visor Extender (If Installed)


B600A01HP-AAT (If installed)


STEERING WHEEL TILT LEVER


B580C01GK


OGK046022


Your vehicle is equipped with sun visor extend- ers that may be used when the visor is in the side glass position.


To adjust the steering wheel: 1. Pull the lever toward you and hold it to unlock. 2. Raise or lower the steering wheel to the


desired position.


3. After adjustment, release the lever.


WARNING:


Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.


gkflhma-1a.p65


78


9/12/2006, 3:17 PM


HORN


B610A01S-GAT


LUGGAGE NET


B540D02HP-GAT (if installed) Type A


Horn Zone


FEATURES OF YOUR HYUNDAI


79


WARNING:


Avoid eye injury. Do not overstretch. Al- ways keep face and body out of recoil path. Do not use when strap has visible signs of wear or damage.


Type B


Press the pad on the steering wheel to sound the horn.


OGK046023


HGK2126
Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor(If installed) or at the back of the luggage compartment to prevent objects from sliding.


B990A03Y-AAT Floor Mat Anchor


CAUTION:


To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the luggage com- partment.


B570A01N


When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.


gkflhma-1a.p65


79


9/12/2006, 3:17 PM


1FEATURES OF YOUR HYUNDAI 80


WARNING:


o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.


o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.


CRUISE CONTROL


B660A02S-AAT (If Installed)


B660B01GK-AAT To Set the Cruise Speed


OGK016660
The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).


NOTE: Cruise control is not recommended for city driving, winding roads, slippery roads, heavy rain, or other bad weather condi- tions.


OGK016661
1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi- nated. This turns the system on.


2. Accelerate to the desired cruising speed


above 25 mph (40 km/h).


3. Push the control switch downward to "SET


(COAST)" and release it. The "SET" indicator light in the instrument cluster will illuminate.


4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.


gkflhma-1a.p65


80


9/12/2006, 3:17 PM


5. To momently increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.


B660C01GK-AAT To Cancel the Cruise Speed


B660D01E-AAT To Resume the Preset Speed


FEATURES OF YOUR HYUNDAI


81


WARNING:


To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control.


OGK016662
To disengage the cruise control system, pull the control switch toward the steering wheel to "CANCEL" position. Additionally, the following actions will disengage the system :


OGK016663
The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL)" position and release it, providing the vehicle speed is above 25 mph (40 km/h).


o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position (Auto-


matic transaxle).


o Decrease the vehicle speed lower than the


memorized speed by 9 mph (15 km/h).


o Decrease the vehicle speed to less than 25


mph (40 km/h).


o Release the main switch.


gkflhma-1a.p65


81


9/12/2006, 3:17 PM


!


WARNING:


o During normal cruise control operation, when the "SET(COAST)" is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.


1FEATURES OF YOUR HYUNDAI 82


B660E01E-AAT To Reset at a Faster Speed


1. Push the control switch upward to "RE-


SUME (ACCEL)" position and hold it.


2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.


B660F03E-AAT To Reset at a Slower Speed


OGK016661


1. Push the control switch downward to "SET (COAST)" and hold it. The vehicle will decel- erate.


2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.


WARNING:


o Keep the cruise control ON/OFF switch off when not using the cruise control to avoid inadvertently setting a speed.


o Use the cruise control system only when traveling on open highways in good weather.


o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.


o Pay particular attention to the driving conditions whenever using the cruise control system.


o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch. o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deacti- vate. This is an indication of normal system operation.


gkflhma-1a.p65


82


9/12/2006, 3:18 PM


AUDIO REMOTE CONTROL SWITCH B610A02GK-GAT (If installed)


POWER ON/OFF Switch


FEATURES OF YOUR HYUNDAI


83


SEEK (UP / ) Switch


Press the SEEK UP ( ) switch 1 sec. or more.


1. RADIO mode


When the SEEK UP ( ) switch is pressed, the unit will automatically tune to the next higher frequency.


2. TAPE mode


Pressing the SEEK UP ( ) switch will play the beginning of the next music segment.


OGK046086L


3. CD (compact disc)/CDC


(compact disc changer) mode


Press the POWER ON/OFF switch to select Radio, Tape, CD (compact disc) and CDC (compact disc changer).


Press the POWER ON/OFF switch once again to cancel Radio, Tape, CD (compact disc) and CDC (compact disc changer).


Press the SEEK UP ( ) switch once to skip forward to the beginning of the next track.


VOL ( / ) Switch


o Press the VOL ( ) button to increase


o Press the VOL ( ) button to decrease


volume.


volume.


gkflhma-1a.p65


83


9/12/2006, 3:18 PM


1FEATURES OF YOUR HYUNDAI 84


HEATING AND COOLING CONTROL


B710A02GK-GAT


B710B02O-AAT Center Ventilator


The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.


B710C01JM-AAT Side Ventilator


The side ventilators are located on each side of the dash board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.


1. Side Defrost Nozzle 2. Side Ventilator 3. Windshield Defrost Nozzle 4. Center Ventilator


OGK016003


gkflhma-1b.p65


84


9/12/2006, 3:18 PM


HEATING AND VENTILATION


FEATURES OF YOUR HYUNDAI


85


B670A01GK-GAT Rotary Type (If Installed)


B670B01GK-AAT Fan Speed Control (Blower Control)


B670E02A-AAT Temperature Control


1. Temperature control switch 2. Air intake control switch 3. Air flow control switch 4. Air Conditioning switch 5. Fan speed control switch 6. Rear window defroster switch


OGK046038N


OGK046045N


This is used to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions.


Cool


Warm


OGK046043


This control is used to adjust the degree of heating or cooling desired.


gkflhma-1b.p65


85


9/12/2006, 3:18 PM


1FEATURES OF YOUR HYUNDAI 86


B670C02Y-AAT Air Intake Control


B670D04O-AAT Air Flow Control


NOTE: It should be noted that prolonged opera- tion of the heating system in " " mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition prolonged use of the air condi- tioning with the " " mode selected may result in the air within the passenger com- partment becoming excessively dry.


This is used to select fresh outside air or recirculation of inside air.


OGK046044


Fresh Recirculation


With the " " mode selected, air enters the vehicle from outside and is heated or cooled according to the other functions selected. With the " " mode selected, air from within the passenger compartment is drawn through the heating system and heated or cooled ac- cording to the other functions selected.


OGK046039N This is used to turn the blower fan on/off and to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and Defrost air position. The MAX A/C mode is used to cool the inside of the vehicle faster. The "OFF" mode is used to turn the blower fan off.


NOTE: If the blower fan is off, the air intake control is set to the fresh mode automatically.


gkflhma-1b.p65


86


9/12/2006, 3:18 PM


FEATURES OF YOUR HYUNDAI


87


OGK016095


OGK016096


OGK016097


Face-Level


Bi-Level


Floor-Level


Selecting the "Face" mode will cause air to be discharged through the side and center venti- lators.


Air is discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.


Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle and side ventilator. If the "Floor" mode is selected, the "Fresh" mode will be activated.


gkflhma-1b.p65


87


9/12/2006, 3:18 PM


1FEATURES OF YOUR HYUNDAI 88


mode except the defrost mode and the floor-defrost mode. Although the A/C switch indicator is turned off, this is normal operation.


OGK016098

Loading...
x